Products Solutions Services

Explosion Protection
Guidelines and General Principles
Explosion Protection
© Light&Magic - shutterstock.com
© Iris Speth - PantherMedia 2
Explosion protection
 Foreword 3

Foreword

In many industry sectors, combustible and potentially There are three prerequisites for an explosion: a combus-
explosive atmospheres in the form of gases, vapors, mists tible gas or dust, oxygen and a source of ignition. Primary
or dusts are a present concern. The coal mining, chemical explosion prevention can be achieved by, for example,
and petrochemical sectors are of particular concern, but inerting the gas atmosphere. On the other hand, secondary
the food industry, mill operation, wastewater and biogas explosion prevention consists of avoiding sources of
production sectors are also affected. These combustible ignition. Manufacturers of devices and protection systems
substances can form a potentially explosive atmosphere must therefore develop and design their devices and
when mixed with oxygen. The explosions occurring when systems so that they present no source of ignition – neither
this atmosphere is ignited can result in severe personal in normal opperation nor in consideration of foreseeable
injury and/or damage to property. To prevent the risk of faults. Design-based explosion prevention limits the effects
explosion, most industrialized nations have developed of an explosion to a tolerable level.
protective precautions in the form of laws, regulations and
standards so as to achieve a high level of safety. This brochure provides an introduction to and overview
of explosion prevention, focusing on device and protection
Based on the frequency and duration of the occurrence of system requirements for use in potentially explosive
potentially explosive atmosphere, the affected sectors, atmospheres. Note that the legal and normative regulations
plants or plant sections are classified into zones of different are subject to ongoing revisions and adaptations to new
degrees of exposure. The operators of these facilities are technical developments. The information contained in this
required to prevent explosion hazards via protective brochure therefore corresponds to the current status at the
measures in potentially explosive atmospheres. time this document was created.

Table of contents

1. General principles and definitions .................................................................................................................................. 5

2. European Community – guidelines .............................................................................................................................. 10

3. North American region – guidelines ........................................................................................................................... 24

4. IECEx program ................................................................................................................................................................ 28

5. Glossary .......................................................................................................................................................................... 30
4 Explosion protection

1. General principles and definitions

Explosion  A sudden, chemical reaction of a combustible

substance with oxygen while releasing high energy leads to
an explosion. These combustible substances can be gases,
mists, vapors or dusts. Three factors must be simultane-
Explosive
ously present for an explosion to occur: atmosphere

• A combustible substance (in corresponding distribution

and concentration) Combustible
Air / oxygen
• Oxygen (in the air) substance

• A source of ignition (e.g. electrical sparks, hot surfaces)

Explosion
Primary and secondary explosion prevention  The
principle of explosion prevention requires that all explosion
prevention measures have a specified sequence defined.
Primary and secondary protective measures are differenti-
ated in this setting. Ignition source

Primary explosion protection refers to all measures that

prevent a potentially explosive atmosphere from occurring.
Explosion triangle
Secondary explosion prevention is required if the risk of
explosion is not at all or only partially eliminated through
primary explosion prevention measures.

A potentially explosive atmosphere is a mixture of air Regarding the ignition source, there is a wide
and combustible gases, vapors, mists or dusts under variety of potential triggers for an explosion:
atmospheric conditions, in which the combustion process
expands of the overall unconsumed mixture once • Open flames
ignition occurs. • Hot surfaces
• Electrical sparks and arcs
Atmospheric conditions are defined at an absolute pres- • Electrical discharges
sures of 0.8 bar to 1.1 bar and mixture temperatures of • Atmospheric discharges
-20 °C to +60 °C. • Mechanical frictional or impact sparking
• Electrostatic discharge
• Ultrasonic
• Optical radiation
• Chemical reaction

1 Primary explosion protection 2 Secondary explosion prevention 3 Design-related explosion

prevention
Preventing the formation of a Preventing the ignition of a
Limiting the effect of an explosion
hazardous, potentially explosive hazardous, potentially explosive
to a tolerable level
atmosphere atmosphere
 General principles and definitions 5

Classification of flammable gases

To assess technical safety, defined characteristic

quantities of combustible substances are necessary
Substance Lower Upper
designation explosion explosion
Explosion limits  A potentially explosive atmosphere limit limit
forms from combustible substances if they are in a defined [vol. %] [vol. %]
concentration range (see image). If the concentrations are
too low (lean mixture) or too high (rich mixture), then no Acetylene 2.3 78.0
explosion occurs, but rather a slow burning process, if any Ethylene 2.3 32.4
at all. The mixture only reacts explosively when ignited in
the range between the upper and lower explosion limit. Gasoline 0.6 8.0
The explosion limits are dependent upon ambient pressure Benzene 1.2 8.0
and the oxygen content of the air. Depending on the speed Natural gas 4.0 13.0
of the elapsing burning process, it may be designated as
a deflagration, explosion or detonation. An potentially Heating oil/diesel 0.6 6.5
explosive atmosphere exists if ignition presents a danger to Methane 4.4 16.5
persons or property. A potentially explosive atmosphere, Propane 1.7 10.9
even one with low volume, can lead to hazardous explo-
sions in a closed room. Carbon disulfide 0.6 60.0
Coal gas 4.0 30.0
Hydrogen 4.0 77.0

Lower Upper
explosion explosion
limit limit

L U
0 vol% E E 100 vol%
L L
Lean Potentially explosive atmosphere Rich
mixture mixture
6 Explosion protection

Explosion limits of combustible substances  In condi- Temperature classes  The ignition temperature of a
tions other than atmospheric conditions (temperatures: combustible gas or liquid is the lowest temperature of a
-20 to +60 °C, pressures: 0.8 to 1.1 bar), the explosion heated surface at which the gas/air or vapor/air mixture
limits change. The concentration range between the just barely ignites. Consequently, the highest equipment
explosion limits becomes extended, generally from increas- surface temperature must always be lower than the ignition
ing pressure and increasing temperature. temperature of the surrounding atmosphere.

The upper explosion limit is significantly higher with Temperature classes T1 to T6 are introduced for electrical
oxygen than with air mixtures. A potentially explosive equipment. Equipment is assigned to the respective
atmosphere can only occur above a combustible liquid if the temperature class based on its maximum surface tempera-
fluid surface temperature exceeds a minimum level. Under ture. Equipment in a higher temperature class can also
certain conditions, some chemically unstable substances be used for applications with a lower temperature class.
have no upper explosion limits. These substances can Combustible gases and vapors are assigned to the
undergo an exothermic reaction even without the presence respective temperature class according to their ignition
of air/oxygen. temperatures.

Temperature class Permissible surface temperature Ignition temperature range for

for electrical equipment [°C] combustible substances [°C]

T1 450 >450
T2 300 >300 to ≤450
T3 200 >200 to ≤300
T4 135 >135 to ≤200
T5 100 >100 to ≤135
T6 85 >85 to ≤100

Classification of explosion groups  For certain explosion

protection measures, particularly intrinsic safety and Explosion groups
flameproof enclosures, the equipment must be marked with
the explosion group it belongs to. Criteria for classification
Explosion Maximum Minimum
are the maximum safe gaps and the minimum ignition
group safe gap [mm] ignition
current. The maximum safe gap and minimum ignition
current ratio
current are measured for various gases and vapors under
precisely defined testing conditions. IIA >0.9 >0.8
IIB 0.5 to 0.9 0.45 to 0.8
The ignitability of the gases increases from explosion group
IIC <0.5 <0.45
IIA to IIC. The requirements for electrical equipment rise
according to the increaseing explosion group. Electrical
equipment permissible for explosion group/gas group IIC
may also be used for all other explosion groups.
Group IIA IIB IIC
Maximum 160 µJ 80 µJ 20 µJ
permitted
ignition
energy (pro- (ethyl- (hydro-
(ignition gas) pane) ene) gen)
 General principles and definitions 7

Solid substances in crushed form – e.g. in the form of dust Minimum ignition energy  A specific amount of energy
or fibers – are frequently present in industrial sectors, e.g. has to be applied to ignite a potentially explosive atmo-
in chemical plants, the food industry or flour mills. Dust is sphere. The minimum ignition energy is the least possible
a finely dispersed solid below a particle size of approx. amount of converted energy (e.g. discharge of a capacitor)
500 µm. If dust layers with small particle size are dispersed, needed to ignite the corresponding combustible mixture.
a risk of explosion is present. The risk of explosion grows The minimum ignition energy is between approximately
with decreasing particle size. Frequently, explosions result 20 µJ for hydrogen up to a few joules for certain dusts.
from dispersed dust layers that contain their own ignition
source. A dust layer of less than 1 mm distributed uniform-
ly on the ground is sufficient to fill a room with normal
ceiling height with a potentially explosive dust/air mixture
when the dust is uniformly dispersed.

Safety relevant data include parameters for dispersed dusts

such as the minimum ignition energy and the ignition
temperature, whereas the glow temperature is a character-
istic property for dust layers.

Gases, vapors Minimum ignition Minimum ignition energy

and dusts energy in mJ (mJ)

(millijoules) 1000
Welding sparks,
Carbon disulfide 0.009 impact sparks
100
Hydrogen 0.017
Grinding sparks
Acetylene 0.019 (cut-off grinder)
10
Benzene 0.20
Ethanol 0.28
1
Methane 0.29 Electrostatic
discharges,
Wood flour 20 – 60 impact sparks
0.1
Sugar 40
Lignite 80 0.01
Gases Dusts Typical ignition sources
Ammonia 680

Minimum ignition energy for various materials

8 Explosion protection

Classification of flammable dusts

Ignition temperature [Tignition]  The lowest temperature

of a hot surface [Tmax(1)], detected under specified test Maximum permitted surface temperature (1):
conditions, at which the most ignitable mixture of dust with Tmax(1) = 2/3 Tignition
air (dust cloud) ignites.

Glow temperature [Tglow]  The glow temperature is the

lowest temperature of a hot surface, detected under
specified test conditions, at which a dust layer with 5 mm
thickness starts to glow.
Maximum permitted surface temperature (2):
If dust layers thicker than 5 mm can form on equipment, Tmax(2) = Tglow - 75 K
the maximum permitted surface temperature [TMax(2)]
must be reduced accordingly. The maximum permitted
surface temperature can be reduced according to the chart
per EN 60079-0.

Example:

Minimum ignition temperature: 330 °C

Minimum glow temperature: 300 °C
• Maximum permitted surface temperature for
dust clouds Tmax(1) = 2/3 x 330 °C = 220 °C
• Maximum permitted surface temperature for
dust layers (5 mm thickness)
Tmax(2) = 300 °C – 75 K = 225 °C
• Permitted surface temperature = 220 °C

In this case, equipment used must have a max. surface

temperature of < 220 °C in case of error.
© BASF - Press Photo
 General principles and definitions 9

Decrease of the maximum permitted surface

temperature in case of increasing dust layer thickness
(chart per IEC/EN 60079-14)

°C

400

300
Max. permitted equipment
surface temperature

200
Glow temperature at
5 mm layer thickness
400 °C ≤ T₅ mm

100 320 °C ≤ T₅ mm < ₄₀₀ °C

250 °C ≤ T₅ mm < ₃₂₀ °C

0
0 10 20 30 40 50 mm
Layer thickness

Thermal insulation increases for thicker dust layers, with If the layer thickness is greater than 50 mm, or if dust
the result that the dust layer can glow even at low housing completely covers the equipment, the glow temperature
temperatures. Therefore, ensure that the equipment must be measured via laboratory testing. This also applies
surface temperature is reduced. This surface temperature for layer thicknesses >5 mm, if the glow temperature at
has to be determined according to the graph above for dust 5 mm layer thickness is <250 °C. Laboratory tests are also
layers between 5 mm and 50 mm. These curves take a necessary if the device is completely submersed in
typical temperature reduction of 75 K into account. combustible dust.
10 Explosion protection

2. European Community
© BASF - Press Photo

Explosion protection in Europe  In the European Union, Explosion protection document in accordance
explosion protection is regulated per ATEX Directives 94/9/ with BetrSichV and ATEX Directive 1999/92/EC  
EC and 1999/92/EC. Compliance with the essential health An explosion protection document must be created that at
and safety requirements of ATEX Directive 94/9/EC least contains information concerning
regarding explosion-protected equipment must be docu- • the risk assessment
mented in the manufacturer's EC-declaration of conformity • the protective measures taken
for the respective equipment. It is presumed that the basic • the zone classification
safety requirements are fulfilled when applying the relevant • compliance with the minimum requirements according
harmonized EU standards (presumption principle). This to Appendix 4. These are divided into organizational
directive's scope of validity extends to potentially explosive measures (instructing the employees, etc.) and into
gas and dust atmospheres in underground and surface technical measures (explosion protection measures).
mining. For the first time, nonelectrical explosion preven-
tion is also addressed here. Regulations for occupational
safety in potentially explosive atmospheres are set forth in
the second ATEX Directive, 1999/92/EC.

This directive contains only the minimum requirements.

When transposing these into national laws, individual
states can supplement further-reaching regulations. Per
Directive 1999/92/EC, the user has to assess the explosion
risks of a plant, classify the hazardous area into zones and
document all measures taken to ensure employee safety in
the explosion protection document.
 European Community 11

Zone classification

Potentially explosive atmospheres are classified into zones atmosphere occurring. Specifications for zone classification
to facilitate the selection of appropriate equipment and to can be found in IEC EN 60079-10 for areas
design proper electrical installations. The zone classifica- with potentially explosive gas and in IEC EN 61241-10 for
tion reflects the probability of a potentially explosive areas with combustible dust.

Gases, Zone 0 A place in which a potentially explosive atmosphere consisting of a mixture with air of
vapors flammable substances in the form of gas, vapour or mist is present continuously, for long
periods or frequently.
Zone 1 A place in which a potentially explosive atmosphere consisting of a mixture with air of
flammable substances in the form of gas, vapor or mist is likely to occur in normal
operation occasionally.
Zone 2 A place in which a potentially explosive atmosphere consisting of a mixture with air of
flammable substances in the form of gas, vapor or mist is not likely to occur in normal
operation but, if it does occur, will persist for only a short period.
Dusts Zone 20 A place in which a potentially explosive atmosphere in the form of a cloud of combustible
dust in the air is present continuously, for long periods or frequently.
Zone 21 A place in which a potentially explosive atmosphere in the form of a cloud of combustible
dust in the air is likely to occur in normal operation occasionally.
Zone 22 A place in which a potentially explosive atmosphere in the form of a cloud of combustible
dust in the air is not likely to occur in normal operation but, if it does occur, will persist for
only a short period.

Zone 2 Zone 22
Zone 1

Filling hopper

Zone 20
Zone 0
Zone 21

Work level

Conveyor

Zone 0 Area with gas above the fluid surface Zone 20 Filling hopper of a bag-emptying station

Zone 1 Immediate vicinity around the open Zone 21 Immediate vicinity (radius of 1 m) around
vent (3 m) the open feed opening

Zone 2 Area outside of Zone 1 (3 m) Zone 22 Area outside of Zone 21 due to settling dust
12 Explosion protection

Types of protection

The types of explosion protection define constructive and Corresponding protection principles have been defined in
electrical circuit technology measures for equipment for use IEC 60079 et. seq. for electrical equipment in an area
in potentially explosive atmospheres. These measures where gas can explode.
prevent spark formation or hot surfaces from igniting a
surrounding potentially explosive atmosphere.

Electrical equipment for explosive gas atmospheres

Abbreviations IEC EN DIN
General requirements 60079-0
Flameproof encapsulation d 60079-1
Pressurized p 60079-2
Powder filling q 60079-5
Oil-immersion o 60079-6
Increased safety e 60079-7
Intrinsic safety i 60079-11
Explosion protection measures n 60079-15
Encapsulation m 60079-18
Intrinsically safe systems 60079-25
Electrical equipment Category 1G 60079-26
Intrinsically safe fieldbus systems 60079-28

The measures according to IEC or EN apply for dust explosion protection

Electrical equipment for areas with combustible dust

Abbreviations IEC EN DIN
General requirements 60079-0
Protection by enclosure t 60079-31
Pressurized p 60079-2
Intrinsic safety i 60079-11
Encapsulation m 60079-18
 European Community 13

© badahos - Fotolia.com

Type of protection “Intrinsic Safety” (Ex “i” )

Ex „i“
An intrinsically safe circuit is a circuit in which neither a
spark nor a thermal effect can cause a certain potentially
explosive atmosphere to ignite.

Charakteristics of the type of protection  “Intrinsic

Safety” is based on the principle of limiting the current and
voltage in a circuit. The energy of the circuit which could be
capable of igniting a potentially explosive atmosphere is Interconnecting of intrinsically safe circuits  When
limited so that neither sparking nor impermissible heating interconnecting equipment with intrinsically safe circuits,
of the electrical components can ignite the surrounding the user must provide a verification of intrinsic safety
potentially explosive atmosphere. showing that the “intrinsic safety” has not been impaired.
Interconnecting involves the following cases:
“Intrinsic Safety” is applied particularly in measurement • two intrinsically safe pieces of equipment
and control technology, since no high currents, voltages • one intrinsically safe piece of equipment with one
and outputs are required there. associated intrinsically safe piece of equipment
• more than one associated or active piece of equipment
Intrinsically safe electrical equipment  Electrical
equipment in which all circuits are intrinsically safe. The rules for interconnecting are provided in the IEC/
EN 60079-14 installation design rules. According to this,
Associated electrical equipment  Electrical equipment the safety-related characteristic values of the equipment's
that includes both intrinsically safe and non-intrinsically input and output parameters have to be compared in order
safe circuits, and that is constructed so that the non-intrin- to verify whether the interconnection of multiple pieces
sically safe circuits cannot impair the intrinsically safe of equipment with intrinsically safe circuits satisfy the
circuits. requirements of intrinsic safety. Interconnection is permit-
ted only if all necessary conditions have been satisfied.
An essential aspect of “Intrinsic Safety” is fault analysis Cable parameters also have to be taken into account which,
with regard to compliance of the limits on voltage, current together with the equipment parameters, influence the
and output. Intrinsically safe electrical equipment and permitted cable lengths. Here, the planner has to create a
intrinsically safe parts of associated equipment are classi- system description, what is called the “intrinsic safety
fied into protection levels “ia”, “ib” or “ic” with respect to verification”, in which the individual pieces of electrical
this fault analysis. Depending on the approval for the gas equipment are specified with the characteristic values,
Ex area (EPL Gx) or dust Ex area (EPL Dx), equipment with including the characteristic values of the connecting cables.
protection level “ia” can be used in Zone 0 or 20. Protection
level “ib” is for use in Zone 1 or 21, and protection level “ic”
is for Zone 2 or 22.

An important protective measure for intrinsically safe

circuits is the safe isolation of intrinsically safe circuits from
non-intrinsically safe circuits. For use in Zone 0, galvanic
isolation between intrinsically safe and non-intrinsically
safe circuits is recommended.
14 Explosion protection

Intrinsically safe electrical equipment and intrinsically safe (safety levels). The safety levels depend on the safety
parts of associated equipment are classified in categories requirements for designing the equipment.

Category of Description Installation of the

intrinsically safe equipment
equipment
Gas/dust Gas Dust
(EPL Gx) (EPL Dx)
ia Intrinsically safe electrical equipment is not allowed Zone 0 Zone 20
to cause an ignition
• During normal operation
• If a single countable error occurs
• If two countable errors occur in the equipment
ib Intrinsically safe electrical equipment is not allowed Zone 1 Zone 21
to cause an ignition
• During normal operation
• If a single error occurs in the equipment
ic Intrinsically safe electrical equipment is not allowed Zone 2 Zone 22
to cause an ignition during normal operation

Power supplies and isolators between the intrinsically safe the necessary voltage and current limitation for use in
and non-intrinsically safe circuits of the apparatus provide potentially explosive atmospheres.

Type of protection “increased safety” Ex “e” This type of protection applies for Ex “e”
apparatus that does not normally generate sparks or electric arcs, does not take
on hazardous temperatures and for which the power supply voltage does not
exceed 1 kV.

Type of protection “flameproof enclosures” Ex “d” The spread of an explosion

is prevented using the “flameproof encapsulation” explosion protection type. The
degree of protection is based on design engineering measures. Penetration of Ex “d”
gases is not prevented. In case of an ignition within the enclosure, the enclosure
will withstand the explosive pressure and the ignition is not transmitted to the
outside. There are no temperatures higher than permitted values on the housing
surface.

Application and combination of types of protection Ex “d” and Ex “e”

Ex “d/e”
“Flameproof enclosures”, usually together with the type of protection “increased
safety”, is the important explosion protection type for measuring devices with
Ex d
high energy consumption. A connection housing with increased safety can be
provided with a customer-side Ex e cable entry to make the electrical installation Ex e
easier for devices with flameproof encapsulation. The flameproof cable bushing
in the Ex d electronics compartment is already installed at the factory.
Ex “m”
Type of protection “encapsulation” Ex “m”  The principle of encapsulation is
to enclose potential sources of ignition in electrical apparatus using a suitable
sealing compound. This prevents ignition of an explosive atmosphere.
 European Community 15

Type of protection Ex “n”  These explosion protection measures can be used for
Category 3G devices. Multiple measures are possible for this purpose:
• Non-sparking apparatus ........................Ex “nA” marking (replaced by Ex ec in future)
• Apparatus with enclosed break.............Ex “nC” marking
• Limited power apparatus .......................Ex “nL” marking (replaced by Ex ic)
• Restricted breathing apparatus .............Ex “nR” marking
• Simplified pressurized apparatus ..........Ex “nP” marking
These protective measures are suitable for use in Zone 2 hazardous areas.
The Ex nL measure has already been converted to the Ex ic type of explosion protec-
tion and is no longer permitted for placing products into the market in Europe after
May 2013. Ex nA will soon be converted to the Ex ec type of explosion protection.

Non-electrical explosion protection  With the release of principles for electrical equipment have been taken over.
Directive 94/9/EC, the EN 13463 standard series (will be This involved adaptations to take into account the special
EN 80079) in Europe also defined constructional regula- requirements for the non-electrical equipment.
tions for non-electrical equipment. Some protection

Non-electrical equipment for use in potentially explosive atmospheres

Abbreviations EN
Basic method and requirements 13463-1
Protection by flow restricting enclosure fr 13463-2
Protection by flameproof enclosure d 13463-3
Protection by constructional safety c 13463-5
Protection by control of ignition source b 13463-6
Protection by liquid immersion k 13463-8

National implementation of Directive 1999/92/EC The

directive was adopted into German law by the German
Ordinance on Industrial Safety and Health (BetrSichV). Equip- Equipment
The German Ordinance on Industrial Safety and Health ment
(BetrSichV), “Ordinance concerning the protection of safety group
and health in the provision of work equipment and its use I Electrical equipment for mines
at work, concerning safety when operating installations endangered by firedamp
subject to monitoring and concerning the organization of II Electrical equipment for potentially
industrial safety and health at work”, contains detailed explosive gas and/or dust
regulations on the operation of Ex installations. One of the atmospheres
regulations in the BetrSichV is that equipment and protec-
tive systems in potentially explosive atmospheres have to
be selected in accordance with Directive 94/9/EC. They
must be provided with the required equipment marking for In the IEC standards and the related EN standards for the
use in the respective zone. dust Ex area Group III was introduced.
Marking example: II 1D Ex ta IIIC
Two groups of equipment are distinguished based on ATEX
Directive 94/9/EC:
16 Explosion protection

Equipment groups

Equipment groups describe the degree of protection and

range of application for equipment (in accordance with
ATEX Directive 94/9/EC). Equipment that has a potential
source of ignition which can cause an explosion must
undergo an assessment of explosion risks. Based on this,
measures must be undertaken corresponding to the basic
safety requirements in order to exclude an ignition risk
from this equipment. Equipment in Equipment Group I is
classified into two categories and equipment in Equipment
Group II into three categories (Category 1, 2 and 3), each
with a different safety level. The required protective
measures depend on the required safety level in each case.

Equipment for use in areas with potentially explosive dust

atmospheres were classified in Equipment Group III.
Equipment Group III introduced via the IEC standardization
is now a new addition in the marking of dust Ex equipment.

Equipment Group I  Equipment Group I applies to equip-

ment intended for use in underground parts of mines, and
in those parts of surface installations of such mines, liable Equipment categories:
to be endangered by firedamp and/or combustible dust (in
accordance with ATEX Directive 94/9/EC). For electrical Category M1  The equipment of this category is not
equipment in Group I (mining), it is assumed that methane allowed to continue being operated once a potentially
is the only combustible gas to occur, but in conjunction with explosive atmosphere occurs.
coal dust. If it is possible for other combustible substances
to occur in these areas, the further subdivision as in Group Category M2  The equipment of this category must
II has to be used. be able to be switched off if a potentially explosive
atmosphere occurs.
Within this equipment group there is a further subdivision
into categories M1 and M2. Equipment in Category M1 has a very high degree
of safety and may continue to be operated even if a
Equipment Group II  Equipment Group II applies to potentially explosive atmosphere arises; equipment
equipment intended for use in other places liable to be in Category M2 has a high degree of safety, but must
endangered by explosive gas or dust atmospheres. Equip- be switched off if a potentially explosive atmosphere
ment Group II is subdivided into three categories depending occurs.
on the occurrence of a hazardous, potentially explosive
atmosphere in the intended area of use.

Electrical equipment in Group II is further subdivided into Subdivision of Group II (gas group)
gas groups according to the characteristics of the poten- • IIA, typical gas is propane
tially explosive atmosphere for which it is intended. • IIB, typical gas is ethylene
• IIC, typical gas is hydrogen
Equipment Group III  The equipment of this group is
intended for operation where a potentially explosive dust
atmosphere is to be expected. Electrical equipment in
Subdivision of Group III (dust group)
Group III is further subdivided according to the characteris-
• IIIA, combustible flyings
tics of the potentially explosive dusts for which it is
• IIIB, non-conductive dust
intended.
• IIIC, conductive dust
 European Community 17

© Nikolay Zaburdaev - Fotolia.com

Equipment categories  The equipment in Groups II and III

is classified into categories 1, 2 and 3 with different safety Equipment categories:
levels.
Category 1  Equipment and systems feature
Additionally, the equipment is marked with a code indicat- a “very high level” of protection
ing the potentially explosive atmosphere where it can be
used. Protection for an explosive gas atmosphere is marked Category 2  Equipment and systems offer
with “G” and with “D” for a combustible dust atmosphere. a “high level” of protection

Information for an equipment category may also involve a Category 3  Equipment and systems offer
mixture of categories. For example, the marking II 1/2 G or a “normal level” of protection
1/3 G means that part of a piece of equipment (such as a
sensor element) fulfills the requirements of Category 1,
while another part (such as a sensor housing with electron-
ics) fulfills the requirements for Category 2 or 3. This
categorization is frequently found on equipment suitable
for installation
in container walls (= zone partition; for example: interior
Zone 0, exterior Zone 1; or interior Zone 0, exterior
Zone 2). The same marking is used also for marking
applications in combustible dust atmospheres.
18 Explosion protection

New IEC marking

Equipment protection level  The equipment for use The marking consists of two letters. The first indicates the
in combustible dust atmospheres was integrated into potentially explosive atmosphere: G for gas, D for dust. The
IEC EN 60079-0. Thus this standard deals with the general actual protection level is defined by the letters a, b or c. This
requirements for equipment for gas and dust atmospheres. marking has been taken over by the installation regulation
The marking for the equipment has been supplemented for electrical equipment in potentially explosive atmo-
by the equipment protection level (EPL). spheres (EN 60079-14/VDE 0165).

EPL Ma Equipment with a “very high” protection level for installation in mines endangered by firedamp.
The equipment of this category may continue to be operated once a potentially explosive
atmosphere has arisen.
EPL Mb Equipment with a “high” protection level for installation in mines endangered by firedamp.
The equipment of this category must be able to be switched off if a potentially explosive
atmosphere arises.
EPL Ga Equipment with a “very high” protection level for use in explosive gas atmospheres.
EPL Gb Equipment with a “high” protection level for use in explosive gas atmospheres.
EPL Gc Equipment with a “normal” protection level for use in explosive gas atmospheres.
EPL Da Equipment with a “very high” protection level for use in combustible dust atmospheres.
EPL Db Equipment with a “high” protection level for use in combustible dust atmospheres.
EPL Dc Equipment with a “normal” protection level for use in combustible dust atmospheres.

The respective equipment has to be selected based on the of equipment for the various potentially explosive atmo-
requirements for installation in Zones 0, 1 or 2 for explo- spheres. The table provides an equipment category assign-
sive gas atmospheres or Zones 20, 21 or 22 for combustible ment and protection level corresponding to the potentially
dust atmospheres. The marking tells you the suitability explosive atmospheres (zones).

Equipment assignment
Directive 1999/92/ ATEX category IEC/EN 60079-0
EC BetrSichV (Directive 94/9/EC) IEC/EN 60079-14
Zone Equipment Equipment Equipment Protection level
group category group (EPL)
I M1 I Ma
M2 Mb
0 II 1G II Ga
1 2G Gb
2 3G Gc
20 1D III Da
21 2D Db
22 3D Dc
 European Community 19

Information on the protection level may also involve a In the past in Europe the marking used the “EEx” symbol.
mixture. For example, the Ga/Gb marking means that part This referred to the European standards. With the current
of a piece of equipment (such as a sensor element) fulfills standards version this is no longer necessary; now “Ex” is
the requirements of protection level Ga, while another part the symbol for marking new equipment. Furthermore, the
(such as a sensor housing with electronics) fulfills the new standards version permits an alternative marking.
requirements for protection level Gb. This categorization Some types of explosion protection have the protection
is frequently found on equipment suitable for installation level supplemented by the letters a, b or c, which is marked
in container walls (= zone partition; for example: interior by the symbol of the explosion protection. The alternative
Zone 0, exterior Zone 1). marking provides for all types of explosion protection to
add these additional letters.

Type of protection Range of applications Range of applications

with gas atmosphere with dust atmosphere
Zone 0 Zone 1 Zone 2 Zone 20 Zone 21 Zone 22
EPL Ga EPL Gb EPL Gc EPL Da EPL Db EPL Dc
Flameproof da db dc
encapsulation
Increased safety eb ec
Intrinsic safety ia ib ic ia ib ic
Encapsulation ma mb mc ma mb mc
Oil-immersion ob
Powder filling qb
Pressurized pxb, pyb pzc pb pc
Protection by enclosure ta tb tc
Energy-limited nL
Restricted breathing nR
Non-sparking nA
Enclosed break nC
20 Explosion protection

Marking  For associated electrical apparatus with type of safety (protection level ia, ib, ic). The type of explosion
protection intrinsic safety that are to be installed in protection for the device is added to the marking. The EPL
non-hazardous areas, the symbols for this type of protec- marking has to be placed after the type of protection on an
tion have to be placed inside square brackets, e.g. associated electrical apparatus. Example [Ex ia Ga]. If an
[Ex ia] IIC. If the device is to be installed in potentially associated electrical apparatus with an “ia” intrinsically
explosive atmospheres, then it has to be protected by safe circuit is installed in an additional type of protection,
another type of explosion protection. Then only the e.g. flameproof enclosure with increased safety, in order to
marking for intrinsic safety is placed in square brackets, install it in Zone 1, then the marking results in Ex de [ia Ga]
e.g. Ex de [ia] IIC T6. The temperature class also has to IIC T6 Gb.
be specified since the device can be located within poten-
tially explosive atmospheres. The IEC/EN 60079-0 standard permits an alternative
marking in cases where the marking has duplicate informa-
The equipment for use in combustible dust atmospheres tion. For some types of protection, the protection level is
was integrated into EN 60079-0:2007. Hence, this stan- appended by adding the letters a, b or c to the marking for
dard deals with the general requirements for equipment for the type of protection. For instance, flameproof enclosure,
gas and dust atmospheres. This allows the protection level “d” can then be marked with “db”. This avoids duplicate
to be added to the marking. This equipment protection level markings. Different markings can currently be found on
(EPL) consists of two letters. The first letter indicates the devices for this reason.
type of potentially explosive atmosphere: G for gas, D for
dust. The protection level itself is defined by the letters a, b
or c, the same way these are taken into account for intrinsic

European International/European standards

Directive 94/9/EC IEC/EN 60079 and later
II 2G Ex de IIC T4 Gb 1 Category 2G: Suitable for Zone 1
2 Flameproof encapsulation/increased safety:
Suitable for Zone 1
1 2 3 3 Equipment protection level Gb:
Suitable for Zone 1

Examples of the new marking

Old marking New marking Alternative marking

II 1G EEx ia IIC T6 II 1G Ex ia IIC T6 Ga II 1G Ex ia IIC T6
II 2G EEx d [ia] IIC T6 II 2G Ex d [ia Ga] IIC T6 Gb II 2G Ex db [ia] IIC T6
II 2G EEx de IIC T4 II 2G Ex de IIC T6 Gb II 2G Ex db eb IIC T4
II 2D EEx tD A21 IP65 T200 °C II 2D Ex tb IIIC T200 °C Db II 2D Ex tb IIIC T200 °C
II 1/2G EEx ia IIC T6 II 1/2G Ex ia IIC T6 Ga/Gb II 1/2G Ex ia IIC T6
II 3G EEx nA IIC T6 II 3G Ex nA IIC T6 Gc II 3G Ex nAc IIC T6
II (1)2 G EEx d[ia] IIC T6 II (1)2G Ex d [ia Ga] IIC T6 Gb II (1)2G Ex d[ia] IIC T6
II (1) GD [EEx ia] IIC II (1) GD [Ex ia Ga] IIC II (1)G [Ex ia] IIC
[Ex ia Da] III B II (1)D [Ex ia] IIIB
 European Community 21

Erecting and operating electrical installations

in potentially explosive atmospheres
Safety in potentially explosive atmospheres must be He or she must ensure that the installation is properly
guaranteed by all involved: manufacturers, installers, installed and inspected prior to commissioning. The
government agencies, inspection bodies and operators. proper condition of the installation has to be ensured
The operator bears responsibility for the safety of his through regular inspections and maintenance. The in-
or her installation. The operator must assess the risk staller has to observe the installation requirements and
of explosion and classify zones in accordance with correctly select and install the electrical equipment.
IEC EN 60079-10 or national rules and regulations.

Potentially explosive atmosphere (gas and dust)

IEC EN DIN
Electrical installations design, selection and erection 60079-14
Electrical installations inspection and maintenance 60079-17
Equipment repair, overhaul and reclamation 60079-19

Installation  Three installation systems are used for

A manufacturer of explosion-proof equipment has to
electrical installations in potentially explosive atmospheres.
provide for a surveilled quality assurance system during the
manufacturing according to DIN EN IEC 80079-34 and
ensure that each device corresponds to the tested design.

Application and combination of Ex “d” and Ex “e” (dual-compartment housing system) and Ex “d”
(one-compartment housing system) explosion protection types

Indirect cable entry Direct cable entry Conduit systems

(dual-compartment (one-compartment (one-compartment
housing system) housing system) housing system)
The cables and wires enter the The connecting cables enter directly The electrical wires are pulled into
connection compartment of the type into the equipment's electronic the closed metal conduit as
of protection “Increased safety” via housing (Ex d). Only cable glands individual wires. The conduits are
suitable cable glands. The terminals specially approved for this may be connected to the housing via
and cable glands are approved in used. special screw fittings and have to
accordance with Ex “e”. The connection be provided with a conduit seal at
compartment (Ex e) is separated from each entry point.
the electronic housing (Ex d) by an The overall conduit system has a
approved cable bushing (Ex d). flameproof design.
22 Explosion protection

The important type of protection for equipment with a protection. With a “one-compartment housing”, designed
corresponding energy supply includes the “Flameproof according to “Ex d” type of explosion protection, the installer
enclosures,” usually combined with the “Increased safety” has to ensure that the correct Ex d cable gland is used and
type of explosion protection. that it is installed accordingly. The pure Ex d technology is an
Here it is particularly important for the user that he or she installation practice used essentially in the United States
can use a simple installation procedure for a “dual-com- (conduit system) or in the offshore area.
partment housing” with the “Ex de” type of explosion

Obligations of the manufacturer, installer and operator

Manufacturer Installer User

Tasks
Development of electrical equipment Selection and installation of Safe operation of the installation.
suitable for use in potentially explosive electrical equipment in accordance
atmospheres. with its intended use.
Obligations
Compliance with the general and Selection and installation in Responsibility for the system's
particular design requirements and the compliance with the installation safety. Zone classification based
current state-of-the-art. requirements and intended use. on the risks of explosion. Verifica-
Applying for the conformity assess- If the installer and user are not tion that the system is in proper,
ment by an independent authority, if identical, the installer is obligated that is, safe condition:
required by the underlying equipment to present the user with an installa- • Before initial commissioning
category. Forwarding of all Ex-relevant tion certificate if requested by the • At certain time intervals
information (approvals) and manufac- user. This certificate confirms that
turer's declarations to the user. the electrical installations corre- The operator has to create an
Production of all electrical equipment spond to the requirements. If such a explosion protection document in
according to the technical documenta- certificate has been presented, the accordance with the German
tion and test samples. user is no longer required to carry Operational Safety Ordinance
out an additional inspection before (BerSichV). This document
the initial commissioning. describes all precautions for
ensuring explosion protection.
This document must provide
various information, including:
determination of the risk of
explosion, classification of the
explosion hazardous areas into
zones (Ex zone plan), organiza-
tional measures (instruction,
warning devices, escape routes,
etc.), and the selection of suitable
equipment corresponding to the
respective zone (Ex-protected
electrical and non-electrical
equipment).

All involved in the planning and installation of explosion- demonstrate the necessary specialized knowledge
proof plants and equipment, such as “responsible persons,” (DIN EN 60079-14).
“planners,” and “skilled workers,” must have and be able to
 European Community 23

© christian42 - Fotolia.com

Overhaul and maintenance  Regular maintenance is The operator must observe the following important
necessary for maintaining the safety of electrical installa- principles during maintenance and repair:
tions in potentially explosive atmospheres.
• Maintaining the system in proper condition
One of the most important principles is: • Continuous monitoring of the electrical system
Work on electrical installations and equipment under • Immediate implementation of necessary maintenance
voltage is strictly prohibited in potentially explosive measures
atmospheres. As an exception, work is permitted on • Proper operation of the system
intrinsically safe circuits. • Stopping operation if a defect cannot be remedied

Legal regulations and standards  National regulations are implemented. Within the European Union, the harmo-
have to be followed when installing installations in poten- nization process in the area of explosion protection has
tially explosive atmospheres. Here one must distinguish largely been completed. Nevertheless, the standards are
between potentially explosive atmospheres in underground continuously being adjusted today for manufacturers as
and surface mining areas. The particulars related to mining, well as for users. This means that both, manufacturers and
however, will not be addressed further here. users, have to regularly verify the technical standards and
regulations relevant to them and, if necessary, adapt their
Beyond Europe, explosion protection is still regulated by equipment to the new requirements.
national provisions. Country-specific differences in the This means a high amount of effort for everyone.
technical requirements and the required approvals involve
a high amount of development and approval effort for the At the international level, the IEC is trying to approach the
manufacturer. Therefore, a globally active manufacturer goal of having “one test and one certificate worldwide” by
has to develop its equipment so that all safety standards introducing the so called IECEx Scheme.
24 Explosion protection

3. North America

Classification of potentially explosive atmospheres   For installation according to the conduit system, electrical
The basic principles of explosion protection are the same wires are pulled into closed metal pipes as individual wires.
everywhere. Nevertheless, in North America technologies The pipes are connected to the housings via screw fittings
and systems in the area of explosion protection for electri- and have to be provided with a conduit seal at each entry
cal equipment and installations have developed which point. The seal is to prevent explosions that could arise
substantially differ from the IEC standards. The differences inside the housing from propagating into the conduit
compared to explosion protection in Europe and in accor- system.
dance with the IEC concern classification of explosion
hazardous areas, design of equipment, and installation of Certification and labeling  In the USA and Canada,
the electrical equipment. electrical equipment for explosion hazardous areas requires
approval. In the USA and Canada, electrical equipment is
In the USA and countries following USA guidelines, tested and approved by nationally recognized inspection
potentially explosive atmospheres are specified in accor- bodies. For the USA, these are Nationally Recognized
dance with NEC 500 to NEC 506 (NEC = National Electrical Testing Laboratories (NRTL), some of which
Code) and, in Canada, in accordance with the CEC (Cana- are UL (Underwriters Laboratories), FM (Factory Mutual),
dian Electrical Code). Areas are generally classified into and CSA (Canadian Standards Association) (refer also to
three classes (Class I to Class III). http://www.osha.gov/dts/otpca/nrtl). In Canada, all
• Class I: Flammable gases, vapors and mists inspection bodies accredited by the Standards Council of
• Class II: Combustible dust Canada (SCC) are approved, such as CSA, QPS, FM.
• Class III: Ignitable fibers and flyings
The potentially explosive atmospheres are subdivided into Equipment must be marked with general data (e.g.
Division 1 and Division 2 based on the frequency or manufacturer name) and explosion protection related data.
duration of the occurrence of these substances. The specifications for this can be found in the NEC, CEC and
corresponding construction regulations of the inspection
In addition to this existing system in 1996, the USA and bodies.
Canada introduced the IEC Zone-system.
This offers users the option of choosing the system that is Class I, II or III, Division 1 and 2  Approved equipment for
technically and economically ideal for them. As with the Class I, Class II or Class III, Division 1 or 2 are to be labeled
IEC standard, the potentially explosive gases of Class I are such that the following information is included:
further subdivided into groups A, B, C and D, and the • Classes, Division
combustible dusts of Class II into groups E, F and G. • Gas/dust group
• Temperature class
Unlike the IEC standard, groups A and B are the most
ignitable gas groups (corresponding to IEC group IIC).
The maximum surface temperature in accordance with
NEC 505 is specified in agreement with IEC in six tem- Example: Class I Division 1 Group C D T6
perature classes T1 to T6 with an additional subdivision Class I, Zone 0, 1 or 2
into temperature subclasses in the division system.

Installation regulations  The installation methods for the

zone concept in accordance with the NEC largely corre-
spond to those of the conventional class/division system.
In addition to using rigid conduits and mineral-insulated
cables in Class I, Division 1 or Zone 1, the use of approved
metal-armored cables is possible.
 North America 25

In the case of equipment for use in Class I, Zone 0, Zone 1 Zone Equipment:  Equipment corresponding to one or
or Zone 2, a distinction is made between “Division Equip- more explosion protection types in accordance with the
ment” and “Zone Equipment.” NEC and CEC are to be labeled as follows:
• Class
Division Equipment:  Equipment approved for Class I, • Zone
Division 1 and/or Class I, Division 2 can also be provided • AEx (USA) or Ex (Canada) symbol
with the equivalent Zone ID: • Abbreviation of the explosion protection type used
• Class I, Zone 1 or Class I, Zone 2 • Gas group IIA, IIB or IIC
• Gas group IIA, IIB or IIC • Temperature class
• Temperature class

Example: Class I Zone 1 IIC T3 Example: Class I Zone 0 AEx ia IIC T5

Comparison of the classification of potentially explosive atmospheres IEC – NEC – CEC

Gases, vapors and mists Dusts Fibers and flyings
(IEC) Class I Class II Class III
USA regulation NEC 505 NEC 500 NEC 500 NEC 500
Canada regulation CEC 18 CEC 18 CEC 18 CEC 18
Classification Zone 0 Division 1 Division 1 Division 1
Zone 1
Zone 2 Division 2 Division 2 Division 2
Groups NEC 505 NEC 500 NEC 500
CEC 18 CEC 18 CEC 18
Zone 0, 1, 2 Div. 1 and 2 E (metals) Div. 1 and 2
IIA (propane) A (acetylene) F (coal)
IIB (ethylene) B (hydrogen) G (grain)
IIC (hydrogen) C (ethylene)
D (propane)
Temperature classes Zone 0, 1 and 2 Div. 1 and 2 Div. 1 and 2 none
T1 ≤ 450 °C T1 ≤ 450 °C T1 ≤ 450 °C
T2 ≤ 300 °C T2 ≤ 300 °C T2 ≤ 300 °C
T2A ≤ 280 °C T2A ≤ 280 °C
T2B ≤ 260 °C T2B ≤ 260 °C
T2C ≤ 230 °C T2C ≤ 230 °C
T2D ≤ 215 °C T2D ≤ 215 °C
T3 ≤ 200 °C T3 ≤ 200 °C T3 ≤ 200 °C
T3A ≤ 180 °C T3A ≤ 180 °C
T3B ≤ 165 °C T3B ≤ 165 °C
T3C ≤ 160 °C T3C ≤ 160 °C
T4 ≤ 135 °C T4 ≤ 135 °C T4 ≤ 135 °C
T4A ≤ 120 °C T4A ≤ 120 °C
T5 ≤ 100 °C T5 ≤ 100 °C T5 ≤ 100 °C
T6 ≤ 85 °C T6 ≤ 85 °C T6 ≤ 85 °C

Explosion protection in North America: Comparison of zones/divisions

26 Explosion protection

Explosion-proof electrical equipment and location of use

Type of protection Symbol Region Can be used in
Increased safety AEx e USA Class I, Zone 1
Ex e Canada Class I, Zone 1
Ex e IEC Zone 1
Flameproof encapsulation XP USA Class I, Div. 1
XP Canada Class I, Div. 1
AEx d USA Class I, Zone 1
Ex d Canada Class I, Zone 1
Ex d IEC Zone 1
Intrinsic safety IS USA Class I, Div. 1
IS Canada Class I, Div. 1
AEx ia USA Class I, Zone 0
AEx ib USA Class I, Zone 1
Ex ia Canada Class I, Zone 0
Ex ib Canada Class I, Zone 1
Ex ia IEC Zone 0
Ex ib IEC Zone 1
Encapsulation AEx m USA Class I, Zone 1
Ex m Canada Class I, Zone 1
Ex ma IEC Zone 0
Ex mb IEC Zone 1
Ex mc IEC Zone 2
Non-incendive equipment NI USA Class I, Div. 2
NI Canada Class I, Div. 2
AEx nA USA Class I, Zone 2
Ex nA Canada Class I, Zone 2
Ex nA IEC Zone 2
Enclosed break AEx nC USA Class I, Zone 2
Ex nC Canada Class I, Zone 2
Ex nC IEC Zone 2
Energy-limited apparatus AEx nL USA Class I, Zone 2
Ex nL Canada Class I, Zone 2
Ex nL IEC Zone 2
(replaced by Ex ic)
Restricted breathing AEx nR USA Class I, Zone 2
Ex nR Canada Class I, Zone 2
Ex nR IEC Zone 2

Explosion-proof electrical equipment and their location of use

 North America 27

© Light&Magic - shutterstock.com

Degrees of protection for housings  Just as IEC 60529

has specified the IP degrees of protection for housings, in
the USA there is Standard No. 250 from NEMA (National
Electrical Manufacturing Association), which covers the
degree of protection for housings.

Comparison of NEMA assignment with IP degrees of protection

Degree of protection as per NEMA Degree of protection Type of protection
as per IEC
1 IP 20
2 IP 21
3 IP 54
3R IP 24
3S IP 54
4 and 4X IP 55
5 IP 50
6 IP 67
6P IP 68
7 Ex II d
8 Ex II d
9 DIP (StEx)
10 Ex I d
12 and 12K IP 52
Degree of protection USA/Europe
28 Explosion protection

4. IECEx Scheme

International explosion protection (IECEx Scheme)  The combined in the new IEC 60079 standard series. This
International Electrotechnical Commission (IEC) is respon- means that IEC 61241 will expire. As a result, the European
sible for global standardization in the area of electrical standards regarding explosion protection will have to be
engineering. The rules and regulations dealing with the oriented to these rules and regulations. This has already
explosion protection of electrical equipment and systems occurred in some areas. However, national standards can
are provided by Technical Committee TC31. Until recently, deviate from these standards. Therefore it is necessary to
the requirements for an area with potentially explosive gas check the extent to which the IEC standards can be applied.
atmospheres were defined in the IEC 60079 standard series
and those for an area with potentially explosive dust were The IEC also classifies potentially explosive atmospheres
defined in the IEC 61241 standard series. Since many into zones.
requirements for the two areas are identical, both areas are

Explosive gas atmospheres

Zone 0 Area in which a potentially explosive atmosphere consisting of a mixture of air and
combustible substances in the form of gas, vapor or mist is present continuously or for
long periods.
Zone 1 Area in which a potentially explosive atmosphere consisting of a mixture of air and
combustible substances in the form of gas, vapor or mist is expected to occur during
normal operation.
Zone 2 Area in which a potentially explosive atmosphere consisting of a mixture of air and
combustible substances in the form of gas, vapor or mist is not expected to occur during
normal operation, or if it is expected, then only rarely and only for a short time.

Areas with potentially explosive dust

Zone 20 Area in which a potentially explosive atmosphere in the form of a cloud of combustible
dust in air is present continuously, for long periods, or frequently.
Zone 21 Area in which a potentially explosive atmosphere in the form of a cloud of combustible
dust in air is expected to occur occasionally during normal operation.
Zone 22 Area in which a potentially explosive atmosphere in the form of a cloud of combustible
dust in air is not expected to occur during normal operation, but if it does occur, then only
for a short time.

Installation and operation of explosion-proof installations  The IEC has created various standards for the operation and
installation of explosion-proof installations:

IEC 60079-14: Electrical installations design, selection and erection

IEC 60079-17: Electrical installations inspection and maintenance
IEC 60079-19: Equipment repair, overhaul and reclamation
IEC 60079-10-1: Classification of areas – Explosive gas atmospheres
IEC 60079-10-2: Classification of areas – Combustible dust atmospheres
 IECEx Scheme 29

IECEx System  The physical principles of explosion These rules have been published in the following IEC
protection are the same around the world. An obvious next documents:
step, therefore, is to regulate the conditions for the ap-
proval of explosion-proof electrical equipment throughout IECEx 01  IEC Scheme for the Certification to Standards
the world. This would create a nationally neutral regulation for Electrical Equipment for Explosive Atmospheres
for global trade. Therefore, the IEC has established a (IECEx Scheme)
certification system with the goal of standardized certifica- • Basic Rules
tion. The IECEx System.
So far the IECEx System is a voluntary certification system IECEx 02  IEC Scheme for the Certification to Standards
with over 30 member countries, of which two (Australia for Electrical Equipment for Explosive Atmospheres
and New Zealand) currently have recognized the certificate (IECEx Scheme)
in their laws. In the rest of the IECEx member countries, • Rules of Procedure
only the IECEx Test Reports are recognized; national
certificates are usually issued on the basis of these reports. The introduction of an online certificate was also important
Worldwide there is a series of recognized IECEx Certifica- for developing the IECEx certification process. This function
tion Bodies, which are accredited and issue certificates in enables full access, including searching, reading and
accordance with standardized international specifications. printing IECEx certificates of conformity that have been
issued. Consequently, this function makes it possible for
The IECEx System consists of 4 certification systems users to have instant global access.
• IECEx Equipment Certification
• IECEx Service Facility Certification The online certificate area is accessed via the regular IECEx
• IECEx Conformity Mark Licensing website
• IECEx Certified Persons www.iecex.com.

With IECEx, a certificate is issued when the type testing has

been passed. The manufacturer has to document that it has
a corresponding quality management system, as is also
required for the national approvals.

At present there are, nevertheless, individual regional and

national approval procedures throughout the world. There
are national regulations for installation as well. The
national differences are very clearly identifiable in the
labeling of equipment. It remains to be seen how long it
will take for global implementation.
Being able to rely on a basis of standards for assessing
installations and selecting equipment is economically
beneficial for both operators and manufacturers. Common,
standardized rules for an international certification process
that supports free international trade have been developed.
© iurii - shutterstock.com 30
Explosion protection
 Glossary 31

5. Glossary
Bibliography

Directive 94/9/EC of the European Parliament and the ATEX Guidelines

Council of 23 March 1994 on the approximation of the Published by: European Commission
laws of the Member States concerning equipment and
protective systems intended for use in potentially explosive Publication
atmospheres; Official Journal of the European Communi- Basic principles of explosion protection
ties, No. L 100/1. R. STAHL Schaltgeräte GmbH, Waldenburg

Directive 1999/92/EC of the European Parliament and of Publication

the Council of 16 December 1999 on minimum require- Automation systems
ments for improving the safety and health protection of Basic principles of explosion protection
workers potentially at risk from explosive atmospheres; Siemens
Official Journal of the European Communities, No. L 23/57.
Publication
German Ordinance on Industrial Safety and Health Explosion protection in accordance with ATEX
(BetrSichV): Ordinance concerning the protection of safety General principles and terminology
and health in the provision of work equipment and its use Endress+Hauser
at work, concerning safety when operating installations
subject to monitoring and concerning the organization of Publication
industrial safety and health at work. Basic principles of explosion protection
Bartec, Bad Mergentheim
Berufsgenossenschaftliche Vorschriften und Regelwerke
(German Employer's Liability Insurance Association IEC Standards
Regulations); Carl Heymanns Verlag KG, Cologne Explosive atmosphere
www.iec.com
EN/VDE-Normen (EN/VDE standards); Beuth-Verlag,
Berlin

EN 60079-0: 2010 (VDE 0170-1)

Explosive atmospheres – Part 0: Equipment –
General requirements (IEC 60079-0:2007)

EN 60079-14: 2009 (VDE 0165 Part 1)

Explosive atmospheres – Part 14: Electrical installations
design, selection and erection
(IEC 60079-14:2007)

EN 61241-14: 2005 (VDE 0165 Part 2) Electrical appara-

tus for use in the presence of combustible dust – Part 14:
Selection and Installation
32 Explosion protection

Marking examples (gas)

II 1/2 G Ex ia IIC T6 Ga/Gb

Equipment
group Equipment protection level EPL Gb (Zone 1)
Category Equipment protection level EPL Ga (Zone 0)
Gases, vapors Temperature class
Explosion group
Installation in the
Zone 0 / Zone 1 zone Intrinsically safe circuit “i” Protection level “a”
partition; equipment Explosion protection
with intrinsic safety

II 1/2 G Ex d [ia] IIC T6 Ga/Gb

Equipment Equipment protection level EPL Gb
group (Zone 1)

Category Equipment protection level EPL Ga (Zone 0)

Gases, vapors Temperature class

Explosion group

Associated intrinsically safe circuit “i” Protection level “a”

Installation in the
Zone 0 / Zone 1 zone Explosion protection “d”
partition; Equipment with
flameproof encapsulation Explosion protection
and intrinsically safe circuit

II 2 G Ex d [ia Ga] IIC T4 Gb

Equipment
group
Category Equipment protection level EPL Gb (Zone 1)

Gases, vapors Temperature class

Explosion group

Equipment protection level EPL Ga (Zone 0)

Explosion protection “i”, Protection level “a”

Installation in Zone 1;
Equipment with flame- Explosion protection “d”
proof encapsulation and
intrinsically safe circuit Explosion protection
 Glossary 33

Marking examples (dust)

II 1/2 D Ex ia IIIB / Ex tb IIIB IP65 T90°C Da/Db

Equipment Equipment
group protection
level
Category EPL Db
(Zone 21)
Dusts Equipment
protection level
EPL Da (Zone 20)
Max. surface temperature
Degree of protection by enclosures
Explosion group III B, non-conductive dust
Explosion protection “tb” protection by enclosure
Explosion protection
Installation in the Zone 20 / Explosion group III, non-conductive dust
Zone 21 zone partition;
Equipment with protection by Explosion protection, Intrinsic safety “i”, Protection level “a”
enclosure and intrinsically safe Explosion protection
circuits

II 2 D Ex mb T100°Db
Equipment
group
Equipment
Category protection level
EPL Db (Zone 2)
Dusts
Max. surface temperature

Installation in Zone 21; Explosion protection, Encapsulation “m”, Protection level “b”
Equipment with protection
Explosion protection
from encapsulation

II (1) GD [Ex ia Ga/Da] IIC

Equipment
group Explosion group

Category Equipment protection level EPL Da (Zone 20)

Gases, vapors, dusts Equipment protection level EPL Ga (Zone 0)

Explosion protection, Intrinsic safety “i”, Protection level "a"
Explosion protection

Associated electrical equipment, Installation

in a safe area; Intrinsically safe circuit suitable
for Zone 0 and Zone 20
34 Explosion protection

Explosion protection terminology

Explosive atmosphere Mixture with air, under atmo-

spheric conditions, of flammable substances in the form of
gases, vapors, mists or dusts in which after ignition has
occured, combustion spreads to the entire unburned
mixture.

Potentially explosive atmosphere  An atmosphere which

could become explosive due to local and operational
conditions.

Hazardous places (areas)  A place in which an explosive

atmosphere may occur in such quantities as to require
special precautions to protect the health and safety of the
© andrewburgess - Fotolia.com

workers. Hazardous places are classified in terms of Zones

in Europe and at IEC and in divisions in North America.

Intrinsically safe circuit  A circuit in which neither a spark

nor a thermal effect can cause a certain potentially explo-
sive atmosphere to ignite.

Electrical equipment  The whole of components, electrical

circuits or parts of electrical circuits usually found in a
single enclosure.

Intrinsically safe electrical equipment  Equipment in

which all circuits are intrinsically safe.

Associated equipment  Electrical equipment that includes

both intrinsically safe and non-intrinsically safe circuits,
and that is constructed so that the non-intrinsically safe
circuits cannot impair the intrinsically safe circuits.
Note:
This can also be seen from the square brackets and paren-
theses in the marking. Associated equipment has to be
installed outside of the potentially explosive atmosphere
if it does not correspond to another suitable type of
explosion protection.

Simple electrical equipment  Electrical equipment or a

combination of components with a simple design and
exactly specified electrical parameters that does not impair
the intrinsic safety of the circuit in which it is to be used.
Glossary 35
 www.addresses.endress.com
CP00021Z/11/EN/13.13 – 71220056