Scribd
Upload
116 views5 pages

How To Install And/Or Upgrade To Hyland Onbase Unity Client V17 Via Software Center

The document provides instructions for installing or upgrading to Hyland OnBase Unity Client V17 using Microsoft System Center Configuration Manager Software Center. It describes how to access Software Center, search for and install the OnBase Unity Client, and then launch the client to log in with CSUSM credentials. Contact IT support if Software Center is not available or the OnBase client is not found.

Uploaded by

Alberto José Segrera Fernández
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
116 views5 pages

How To Install And/Or Upgrade To Hyland Onbase Unity Client V17 Via Software Center

The document provides instructions for installing or upgrading to Hyland OnBase Unity Client V17 using Microsoft System Center Configuration Manager Software Center. It describes how to access Software Center, search for and install the OnBase Unity Client, and then launch the client to log in with CSUSM credentials. Contact IT support if Software Center is not available or the OnBase client is not found.

Uploaded by

Alberto José Segrera Fernández
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

How to Install and/or Upgrade to

Hyland OnBase Unity Client V17 via Software Center


This document will walk you through installing and/or upgrading the Hyland OnBase Unity Client
software via Microsoft System Center Configuration Manager Software Center (aka. Software Center).

The new Hyland OnBase Unity Client v17 operates the same as the old Hyland OnBase Unity Client v15
and is very similar visually to use. Hyland OnBase Unity Client v17 replaces the older Hyland OnBase
Unity Client v15 that was retired on 5/9/19.

Please Note:
1. The Hyland OnBase Unity Client is available to either On Campus PC Computers with a wired
network connection (i.e. No Mac install) or via CougarApps for Mac, Off Campus or On Campus
Wireless Connections.
2. If you are following the below instructions and are not able to run Software Center and/or do
not see the OnBase Unity Client within Software Center, please stop and contact the
[email protected] or call x4790. They will need to make a HelpSpot ticket to update your
computer and/or access for Software Center.

Access OnBase Unity Client from Software Center


1. Click on the Windows Search icon in the bottom left (next to the Windows Start button)
2. Type ‘software center’
3. Click on the Software Center application
**If you are not able to run Software Center and/or do not see the OnBase Unity Client with Software
Center, please stop and contact the [email protected] or call x4790. They will need to make a
HelpSpot ticket to update your computer and/or access for Software Center.

4. Type ‘onbase’ in the Search box in the top right


5. Click on the Hyland OnBase Unity Client V17 icon

6. The screen will change to the installation screen. Click the ‘Install’ button.
7. Please wait a minute or two for the install to complete.
a. To confirm the installation is complete:
i. Click the ‘Installation status’ tab to the left
ii. Type ‘onbase’ in the search box at the top right
iii. You should see Hyland OnBase Unity Client V17
iv. The right column is ‘Status’ and should say ‘Installed’
v. Close the Software Center window after the Hyland OnBase Unity Client V17 has
been installed.
Starting OnBase Unity Client
1. You can start the OnBase Unity Client a couple of ways:
a. By the OnBase Unity Client shortcut on your desktop

b. By using Windows Search


i. Clicking on the search icon in the bottom left (next to the Windows Start button)
ii. Type ‘unity’
iii. Click the OnBase Unity Client application
c. By scrolling through the Windows Start Menu
i. Clicking on the Windows Start Button
ii. Scroll to the letter ‘H’
iii. Click on ‘Hyland’
iv. Click on ‘OnBase Unity Client’

2. The ‘Unity Client’ login page will appear


a. Enter your CSUSM username and password

You might also like