Scribd
Upload
108 views19 pages

RG-WALL 1600 Next-Generation Firewall Installation and Initialization

The document provides instructions for initializing the RG-WALL 1600 Next-Generation Firewall, including hardware installation, selecting an operating mode of NAT or transparent, configuring interface IPs, default routes, security policies, and upgrading firmware. It emphasizes changing default passwords and limiting management access after setup.

Uploaded by

kareng naw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
108 views19 pages

RG-WALL 1600 Next-Generation Firewall Installation and Initialization

The document provides instructions for initializing the RG-WALL 1600 Next-Generation Firewall, including hardware installation, selecting an operating mode of NAT or transparent, configuring interface IPs, default routes, security policies, and upgrading firmware. It emphasizes changing default passwords and limiting management access after setup.

Uploaded by

kareng naw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

RG-WALL 1600 Next-Generation

Firewall Installation and Initialization

Applicable to V5.2-R5.0
Contents

■ Preface
■ Hardware Installation
■ Initialization Setup
Preface

Audience
Ruijie business partners and customers who are responsible for configuring
and maintaining Ruijie wireless devices.

Revision Record
Release Date Change Contents Reviser

2016.06 Initial publication V1.0 TAC Oversea

Note :
For more detail configuration , see configuration guide for each product . you can download
configuration guide at http://www.ruijienetworks.com
For more technical enquiry , you can visit Ruijie Service portal at
http://case.ruijienetworks.com . You need to sign up before submit a case.

Page 3
Contents

■ Preface
■ Hardware Installation
■ Initialization Setup
Hardware Installation

Device installation in Grounding and


Preparation
specified locations cable connection
A ground bar is provided in the installation environment
(recommended):
① Remove the ground screw from the rear panel of the
device.
② Put the OT terminal of the ground cable delivered with
the device on the ground screw of the chassis.
③ Install the ground screw with the OT terminal to the
ground hole, fasten it with a screwdriver, and connect the
other end of the ground cable to the ground bar of the
equipment room.
A ground bar is not provided in the installation
1 Rear panel of the device
environment:
If the device adopts AC power supply, the PE cable of the 2 Grounding label
AC power supply needs to be grounded. Check whether the 3 Grounding hole
PE cable of the AC power supply is properly grounded in the
4 OT terminal of the
power distribution room or on the AC transformer side.
protective ground cable
5 Protective ground cable
6 Ground screw
Contents

■ Preface
■ Hardware Installation
■ Initialization Setup
Operating Modes

Device login Fast configuration Upgrade

Fast configuration in NAT (routing) mode


Step 1: Select an operating mode. The default is NAT (routing) mode.

NOTE:
The firewall operates either in NAT or transparent mode. The default
is NAT mode. If both modes are adopted, VDOM must be
implemented.
Interface IP Address

Device login Fast configuration Upgrade

Fast configuration in NAT (routing) mode


Step 2: Configure the IP address of the specified interface.

NOTE:
When you configure the IP address of the interface, you can configure its management authority at
the same time. For example, if you select TELNET, you can use the IP address of the interface to
manage the firewall via telnet. If you do not select TELNET, management via telnet is disabled.
Default Route

Device login Fast configuration Upgrade

Fast configuration in NAT (routing) mode


Step 3: Configure the default route.
Security Policy

Device login Fast configuration Upgrade


Fast configuration in NAT (routing) mode
Step 4: Configure a policy for Internet access.

NOTE:
By default, the system has the Internet access policy used to
route traffic from the internal interface to the Wan1 interface.
Security Policy

Device login Fast configuration Upgrade


Fast configuration in NAT (routing) mode
Step 5: Enable the antivirus feature.

NOTE:
Enable the UTM virus
detection feature
and enable antivirus. You
also need to select
protocol options (the
protocol option is
automatically selected).
Security Policy

Device login Fast configuration Upgrade


Fast configuration in NAT (routing) mode
Step 6: Enable trafficcontrol per ip address.
Operating Modes

Device login Fast configuration Upgrade

Fast configuration in transparent mode


Step 1: Select an operating mode. The default is NAT (routing) mode.

NOTE:
The firewall operates either in NAT or transparent mode. The default is NAT
mode. If both modes are adopted, VDOM must be implemented.
Operating Modes

Device login Fast configuration Upgrade

Fast configuration in transparent mode


Step 2: Configure the management IP address and the gateway.

NOTE:
The firewall operates either in NAT or transparent mode. The default is NAT
mode. If both modes are adopted, VDOM must be implemented. If the
transparent mode is adopted, the management IP address must be configured.
Operating Modes

Device login Fast configuration Upgrade

Fast configuration in transparent mode


Step 3: Configure a policy for Internet access.

NOTE:
Disable NAT in transparent mode. By
default, NAT is disabled.
Security Policy

Device login Fast configuration Upgrade


Fast configuration in transparent mode
Step 4: Enable the antivirus feature.

NOTE:
Enable the UTM virus
detection feature
and enable antivirus. You
also need to select
protocol options (the
protocol option is
automatically selected).
Security Policy

Device login Fast configuration Upgrade


Fast configuration in transparent mode
Step 5: Enable trafficcontrol per ip address.
Changing the Administrator Password

Device login Fast configuration Upgrade

Change the administrator account and password, and configure the management host.

NOTE: After device configuration, you are advised to change the


administrator account and password. Only the IP addresses of trusted
hosts can be used to manage the firewall.
Initialization Setup

Device login Fast configuration Upgrade

Version upgrade
To upgrade the system version, do the following:

NOTE: After upgrade, restart the system to make the new version
take effect. Each model corresponds to a version, and the same
version is not applicable to all models.

You might also like