Mi Robot Vacuum-Mop Cleaner

Model : STYTJ02YM
User Manual

Represented by https://fr.aliexpress.com/item/4000095616285.html
Please read this manual carefully before use and keep it properly. The adapter supplied with this product can only be used
at an altitude below 2000m.
Product Introduction.............................................................................................................................................1-3

Installation Instructions........................................................................................................................................4-5

Operation Instructions......................................................................................................................................... 6-7

Routine Maintenance......................................................................................................................... 8-9

Basic Parameters..................................................................................................................................................10

Troubleshooting.................................................................................................................................................... 11

Common Problems............................................................................................................................................... 12

Restrictions on Use.............................................................................................................................................. 13

Warranty Certificate.............................................................................................................................................. 14
Product Introduction
Robot

Intelligent recharging
Short press it to start intelligent recharging

Startup and shutdown/global cleaning

Short press it to start/suspend cleaning

Long press it for 3s to start up or shut down the robot

Blue light remains on: Working normally

Yellow light blinks slowly: Returning for recharging / low battery
Yellow light breathes: Charging
Blue light blinks slowly: Entering the network configuration mode
Blue light breathes: Starting up / Upgrading firmware
Red light blinks fast: Abnormal state

Network configuration
In power-on state, press and hold and
simultaneously for 3s to enter network configuration.

Cover opening
Tip: The dustbin can be removed by opening the top
cover from here.

1
Product Introduction
Robot and Sensor

Laser radar Collision sensor Side brush Left wheel

Top cover Universal wheel Boundary sensor Right wheel

Button Charging electrode Cover for middle motor

Infrared receivingsensor Battery Rolling brush

2
 Product Introduction
Water Tank
Charging Dock

Water inlet Signal

transmitting area Charging indicator
Water tank Charging
electrode Charging electrode

Water tank clip

Cable slot

Dustbin component Duster component

Duster
Dustbin

HEPA
Duster bracket

Sticking
Filter mesh Clip

3
 Installation Instructions
1. Connect the power cord, and collect the redundant cable. 3. Startup and charge.
Long press for 3s; the indicator light on the robot comes
on, connect the robot to the charging dock for charging.

* Please put the redundant cable into the cable slot at the bottom
of the charging dock, otherwise the cable may be dragged and
disconnect power supply to the charging dock.

2. Place the charging sock against a wall, and connect the

power supply.

White light remains on: Startup finished / working normally

WiFi connected / charging finished

Yellow light breathes: Charging

>0.5m
Red light blinks: Abnormal state

>1.5m >0.5m
* In case of low battery, it is possible that the robot cannot start up or shut
down. Please directly connect the robot to the charging dock.
* Please ensure a space of at least 0.5m on both the left and right .
sides of the charging dock, and a space of at least 1.5m in front of it; * The robot will start up automatically after connection to the charging doc k
* Do not expose the charging dock to direct sunlight. * The robot cannot shut down while it is connected to the charging dock.

4
 Installation Instructions
③ Attach the duster into the duster bracket, and stick
4. Install the water tank the duster to the Velcro.
① Open the rubber cover of the water tank;
fill the water tank with water; then close the rubber cover.

④ Manually press the clips on both sides of the duster

bracket, and push the duster bracket to the bottom of
the robot in the indicated direction.

② Install the water tank into the robot in the indicated

direction; confirm that the clip is properly installed.

* Do not use the water tank in the first cleaning;

* Do not use the water tank if the robot is unattended;
* Remove the water tank and duster bracket before charging
the robot or leaving it idle;
* If carpets are used in the house, please set virtual walls
in the App.

5
Operation Instructions
1. Startup/shutdown
The robot will start up automatically while it is being charged on the charging dock.
The robot cannot shut down while it is being charged on the charging dock.
Long press the Power Button; the power indicator light comes on, and the robot enters the power-on state; after startup, a prompt tone will be heard.
When the robot is stationary, long press the Power Button to shut it down; there will be a voice prompt indicating shutdown.

2. Cleaning
1. In power-on state, short press the power button; the voice prompt “Enter global cleaning” will be heard.
2. In power-on state, short press the Recharge Button; the voice prompt “Enter recharge mode” will be heard.
3. Enter the device home page via the App; click the “Start” button to start cleaning. The voice prompt “Enter global cleaning” will be heard.
4. Enter the device home page via the App; click the “Recharge” button to start recharging. The voice prompt “Enter recharge mode” will be heard.
* In case of low battery, the cleaning function cannot be enabled.

3. Recharging
1. When the robot finishes cleaning, the voice prompt “Cleaning is finished. Enter the recharge mode” will be heard. The robot will get recharged
automatically.
2. In case of low battery during cleaning, the robot will get recharged automatically; after it gets fully charged, it continues where it stops previously.
3. The robot shuts down automatically if the battery is exhausted, you can manually put back the robot to the charging dock for charging. Please ensure that
the charging electrodes are in good contact.

4. Network configuration & firmware upgrade

Scan the QR code on the robot to download the App; connect the device according to instructions in the App. You can also refer to video guide in store link.
With the App, you can directly query and update the device firmware. During upgrade, ensure that the device is in charging state and that the battery level is
no less than 60%. For update steps, please see the guide provided in the App.
* After successful download, carry out network configuration according to the prompts in the App. When the robot is connected to the Internet, you can use the
App to remotely start cleaning, schedule cleaning and realize other functions.
* The robot does not support WiFi networks at 5.8G frequency band.
* App unbinding: Press the Recharge Button for 5s and release it when a sound is heard; then press the Recharge Button again for 5s, and the voice prompt
“Initialization starts / Initialization successful” will be heard.

6
 Operation Instructions
In the DND period , the robot will not respond to Resume
Pause Cleaning,
When the robot is in operation, press any button to pause; press Scheduled Cleaning or give voice prompts. The DND mode is
to continue cleaning; press to return to the charging dock enabled during 22:00-07:00 by default, and can be disabled via
and end the current cleaning task. the App on the mobile phone.

Sleep Resume Cleaning mode

If no operation is performed within 5min, the robot will automatically The robot resumes where it left off. If the battery runs out during
enter sleep state. In this state, you can wake up the robot by cleaning, the robot will automatically return to the charging dock to
pressing the button or via the App. charge itself. After it is fully charged, it will resume where it
The robot will not enter sleep state while it is being charged on the previously stops (if cleaning is manually ended during charging,
charging dock. the robot will cancel the resume cleaning task).
The robot will shut down automatically when the sleep time
exceeds 12h. User-defined area
With the App, you can define the areas to be cleaned, and the
Fault state robot will clean these areas.
In case of any abnormality during operation, the red button light will
blink fast and a voice prompt will be heard. For the solution, please Clean designated area
see the “Troubleshooting” section. With the App, you can designate a target position on the map. The
If, in fault state, no operation is performed within 5min, the robot will robot will automatically plan the route to the designated position
enter sleep state automatically. and start cleaning in 2*2 square areas.

Refill the water tank or clean the duster during cleaning Scheduled cleaning
If it is necessary to add water or clean the duster during cleaning, With the App, you can schedule the cleaning. The robot will start
first press any button to pause; then remove the water tank, and add cleaning at the designated time, and automatically return to the
water or clean the duster; after that, put back the water tank and charging dock after cleaning.
duster, and press to continue.
Virtual walls
Cleaning preference With the App, you can set Virtual Walls to prevent the robot from
With the App installed on the mobile phone, you can select a mode entering areas that do not require cleaning.
among ECO, Standard and Strong; the default is Standard mode.
Map memorization
Do Not Disturb (DND) mode If Memorize Map is enabled in the App, the robot will save the
updated map and virtual walls after cleaning and successful
recharging.

7
 Routine Maintenance
Dustbin
3. Use the cleaning brush to clean the dustbin,
1. Open the top cover to take out the dustbin, as shown in the figure.
and put ba.ck the HEPA component

2. Open the HEPA component; take it out and empty it. 4. Reinstall the dustbin, close the top cover.

8
 Routine Maintenance
Side Brush
HEPA Component Remove and clean the side brush regularly.
Follow the figure to remove the HEPA component and clean it.

Rolling Brush Boundary Sensor

1. Turn over the lower clip to remove the cover for the middle motor; Clean the boundary sensor with soft cloth regularly
2. Take out the rolling rush and clean the bearing;
3. Clean the rolling brush;
4. Reinstall the rolling brush and fasten the clip of the cover.
Note: Replace the rolling brush every 6-12 months to ensure the cleaning
effect. Boundary sensor
Cover for middle motor
Clip

Rolling brush
Bearing

■ Replace the HEPA component every three months as it is

notwashable;
■ Clean the HEPA component with cleaning brush regularly
to avoid blockage;
■ Replace the side brush every three months to ensure the
cleaning effect.

9
Basic Parameters
Robot Charging Dock
Name Parameter Over dimensions 153.9mmx74.6mmx99.5mm
Over dimensions Φ350mmx94.5mm Rated power 24W
Product weight Approx. 3.27kg Rated input 20V 1.2A
Rated voltage 14.8V Rated output 20V 1.2A
Rated power 40W Rated frequency 50/60Hz
Battery capacity 3200mAh

Names and Contents of Hazardous Substances in the Product

Hazardous substances
Part name
Pb Hg Cd Cr(VI) Pbb Pbde
Metals X ○ ○ ○ ○ ○
Printed circuit boards ○ ○ ○ ○ ○ ○
Plastics ○ ○ ○ ○ ○ ○
Standard parts (screw,
○ ○ ○ ○ ○ ○
washer, etc.)
Other metal structural parts
○ ○ ○ ○ ○ ○
(motor, decorative part*, etc.)
This table has been prepared in accordance with SJ/T11364-2014
: Indicates that the content of this hazardous substance in all materials of the corresponding part is below the limit specified in GB/T 26572-2011.
X: Indicates that the content of this hazardous substance in at least one homogeneous material of the corresponding part is above the
limit specified in GB/T 26572-2011.
Currently, the part marked “X” , which contains substances or elements that are not environmentally friendly, cannot be completely
replaced by one containing no such substances or elements due to the limited level of global technology and process. Technological Marking for the restriction of the
improvements will be made gradually in the future. use of hazardous substances

*: Indicates some product models contain this part.

All the above symbols are subject to the Measures for the Administration of the Restricted Use of the Hazardous Substances in China and the supporting
standard SJ/T11364. Long-term use of the product will not cause harm to human health, so you may rest assured.

10
 Troubleshooting
Fault prompt Solution
Check or clear foreign objects around the laser radar, or move the robot to a new position
Abnormality 1: Please confirm that the laser radar is not blocked.
and restart it.
Abnormality 2: Please wipe the boundary sensor and move the Wipe the boundary sensor and retry (for the sensor position, please consult the
robot to a new position for restart. Instruction Manual).
Abnormality 3: Intense magnetic field is detected. Please move
Move the robot to a new position and retry.
to a new position and retry.
Abnormality 4: Please check and clear up foreign objects on the
Press the collision strip, clear foreign objects and restart.
collision sensor.
Abnormality 5: Robot temperature is abnormal. Please wait until The robot temperature is too high or too low. Wait until the temperature becomes normal
the temperature becomes normal. before reuse.
Check whether the power adapter used is the one originally supplied with the product, and
Abnormality 6: Charging is abnormal. Please clear up the
whether the charging dock is placed horizontally. Turn off the robot, cut off power supply
charging contact area.
to the charging dock, wipe the metal contacts.

11
Common Problems
Problem Solution
The battery level is too low; connect the robot to the charging dock for charging.
Power-on failure
The ambient temperature is too low (<0℃) or too high (>50℃).
Fail to start cleaning The battery level is too low; connect the robot to the charging dock for charging.
There are too many obstacles near the charging dock; place the charging dock in an area free of
obstacles.
Recharging failure
The robot is too distant from the charging dock; place the robot near the charging dock and
retry.
Abnormal actions Shut down and restart the robot.
The rolling brush, side brush or left/right wheel may be entangled with foreign objects; stop the
Abnormal sound during cleaning
robot and clear them up.
The dustbin is full; clear up the dustbin.
Degradation of cleaning capacity or dust come-off The HEPA component is blocked; clear it up.
The rolling brush is entangled with foreign objects; clear up the main brush.
Wi-Fi signal is weak; ensure that the robot is in an area with good Wi-Fi signal.
Fail to connect to Wi-Fi
Wi-Fi connection is abnormal; reset Wi-Fi and download the latest App, then try again.
Confirm that the robot is not in DND mode since it will not continue cleaning in this mode.
Resume cleaning failure
The robot will not continue cleaning when it is manually brought to the charging dock.
Ensure that there is sufficient space around the charging dock, and that the surfaces of the
Charging failure
electrodes are free from dust and coverage.
Confirm that the device has been connected to the network; otherwise synchronization failure
Fail to do scheduled cleaning
may result and timed cleaning tasks won't be performed.
Confirm that the device has been successfully connected to the network and it is always in the
The robot is always in off-line state
range covered by Wi-Fi signal.
Ensure that the charging dock and the robot are in the area with good Wi-Fi signal; reset Wi-Fi
Fail to pair the mobile phone with the device
according to the steps described in the Instruction Manual; then pair again.

12
 Restrictions on Use
■ This product only applies to cleaning of house floors, and should not be used in outdoor areas (e.g., balcony), areas other than floors (e.g., sofa), or
commercial or industrial environments;
■ Do not use the product in environments (e.g., duplex floor, balcony, top of furniture) that are not equipped with guardrails;
■ Do not use the product in environments where the temperature is above 40℃ or below 0℃ or where any liquid or slime exists on the floor;
■ Put away all cables in the house prior to use, to prevent them from being dragged during running of the robot;
■ Put away all fragile objects and sundries (e.g. vase, plastic bag) on the floor, as the robot may get blocked or gently hit obstacles and damage the
valuables in the house;
■ Never allow any persons with physical, mental or perceptual disorders (including children) to use or operate this product;
■ Never allow children to play with the robot; when the robot is working, keep children and pets away from it;
■ Do not place objects, children or pets on the robot whether it is stationary orrunning;
■ Do not use the product to clean any burning objects (e.g., burning cigarette butt);
■ Do not use the product to clean shag carpets (it is possible that some dark carpets cannot be cleaned);
■ Do not use the product to collect hard or sharp objects (e.g., decoration wastes, glass, iron nails);
■ Do not use the laser radar protective cover as a handle to move the device;
■ Clean or maintain the robot and charging dock in power-off or idle state;
■ Never sprinkle any liquid into the product (the dustbin should be wiped dry before reinstallation);
■ Do not place the robot upside down as it may damage the laser radar;
■ Use the product according to the Instruction Manual or the Quick Guide. Any loss or injury caused by improper use shall be on user’s own account.

■ Do not use any battery, power adapter or charging dock supplied by a third party.
■ Do not use non-rechargeable batteries.
■ Never attempt to remove, repair or modify the battery or charging dock.
■ Do not place the charging dock near heat sources (e.g., heating radiator).
■ Do not use a wet cloth or any liquid to wipe this product.
■ Do not dispose of waste batteries at will. It is suggested to hand them over to a professional organization for treatment.
■ Transport the product in power-off state in the original packaging box.
■ If the product is to be left unused for a long time, please turn off the robot after full charging, and store it in a cool, dry place; recharge it at least once a
month to avoid battery damage.

The laser radar of this product complies with the requirements of IEC 60825-1:2014 on the safety of Class 1 laser products; it will not produce laser radiation
harmful to human health.

13
After-sales warranty ( replacement parts, repair or return) are provided for this product, the services cover the following:

Warranty Period
■ You may choose to return, replace or repair the product in case of any performance failure not caused by man-made reasons within 7
days from the date of purchase;
■ You may choose to replace or repair the product in case of any performance failure not caused by man-made reasons within 15 days from
the date of purchase;
■ We will provide replacement parts or local services free of charge for any performance failure not caused by man-made reasons
within the warranty period.

Non-warranty Regulations
The warranty is valid only when the product is used normally. Any man-made damage and the following situations are not covered by the
warranty:
1. The product gets damaged due to user’s negligence, fault, misuse or disaster (e.g., adherence of food or liquid, water ingress, crack due to
external force, scratches and damage of peripheral components);
2. User has disassembled the device, or repaired or modified the device without authorization by the manufacturer (e.g., damage caused by
change of color, use of additional part, or unauthorized modification);
3. The product gets damaged due to connection with any improper accessory or as a result of transport or other accidents;
4. The Warranty Certificate is absent (expect that user can prove the product is within the warranty period), or the warranty period has
expired;
5. The content indicated in the Warranty Certificate is inconsistent with the actual product or has been altered;
6. The product gets damaged due to force majeure factors.

14
 Warranty Card
(Show This Card before Service)
Warranty Period
Model Items Warranty Period
Warranty Period Robot (DD/MM/YYYY) Robot 1 year
Name Battery 6 months
User Name
Address Charging dock, power adapter 1 months
Name Consumables: side brush,
Store Seal Not covered
Address cleaning tool

Thanks for purchasing our smart cleaning robot! In order to guarantee your rights and interests, Note: 1. This guarantees basic maintenance services.
Customer Service hereby promises you standard services and is always ready to serve you The warranty period for any promotional product is
whenever you need. subject to the actual situation.
1. Please keep your Warranty Card properly;
2. When the product you purchased needs service, please complete the warranty information
table and make sure your handwriting is clear and legible;
3. To enjoy our after-sales services, please present your Warranty Card and relevant purchase
information. If the product is purchased online, please provide your account on the platform
where you purchased the product so that you can enjoy relevant after-sales services;

Warranty Principles
1. If the product has any quality problem other than those due to man-made damage or
unauthorized disassembly or repair, you may have it replaced at the store where you
purchased the product within 7 days from the date of purchase;
2. The product is entitled to free service within the warranty period;
3. The following situations will void the warranty, but we can provide charged services for which
the accessory and labor costs will be on your own account.
A. Man-made damage, including damage caused by use in abnormal operating environments
or without observing the Instruction Manual;
B. User’s unauthorized disassembly, repair or modification of the product, or repair by a
person not from our servicedepartment;
C. Damage caused by force majeure events (e.g., fire, earthquake, lightning stroke);
D. Absence of the Warranty Card or any valid certificate of purchase, and no other means to
verify user’s information;
E. Failure to check and verify the date of purchase.
User Manual for Mi Robot Vacuum-Mop Cleaner