To Be Filled Out by The Processing Officer: Tesda-Op-QSO-02-F07 Rev. No. 00-03/01/17

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 5

TESDA-OP-

QSO-02-F07
Rev. No. 00-03/01/17

Reference No. EPA 1 9 0 9 8 3 1 3 4 0 0


to be filled out by the Processing Officer

SELF-ASSESSMENT GUIDE (PERFORMANCE ASSESSMENT)


ELECTRONICS PRODUCS ASSEMBLY AND
Qualification Title SERVICING NC II

COC 1 Title ASSEMBLE ELECTRONICS PRODUCTS


Instruction
 Read each question in the left-hand column of the chart.
 Mark a check opposite each question to indicate your answer.
Can I? YES NO
 Obtain and clarify work instructions
 Identify, prepare and obtain parts and components needed
 Prepare and check required materials, tools and equipment
 Prepare electronic components for assembly*
 Verify PCB layout in conformity with the schematic diagram
 Prepare/Make printed circuit board modules *
 Clean PCB based on standard procedures
 Test and visually inspect the functionality of the PCB
 Mount and solder electronic components *
 Apply soldering/de-soldering techniques and procedures
 Check soldered products
 Assemble electronic components *
 Integrate modules and accessories
 Perform assembly procedures of electronic products
 Test and inspect assembled electronic products *
 Subject finished products to final visual/sensory inspection
and testing
 Apply safety rules and procedures *

I agree to undertake assessment in the knowledge that information


gathered will only be used for professional development purposes and
can only be accessed by concerned assessment personnel and
manager/supervisor.

Date:
Candidate’s Name &Signature:

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 1
TESDA-OP-QSO-02-F07
Rev. No. 00-03/01/17
Reference No. EPA 1 9 0 9 8 3 1 3 4 0 0
to be filled out by the Processing Officer

SELF-ASSESSMENT GUIDE (PERFORMANCE ASSESSMENT)


ELECTRONICS PRODUCS ASSEMBLY AND
Qualification Title SERVICING
SERVICE CONSUMER ELECTRONICS PRODUCTS AND
COC 2 Title
SYSTEMS
Instruction
 Read each question in the left-hand column of the chart.
 Mark a check opposite each question to indicate your answer.
Can I? YES NO
 Prepare the unit and required materials, tools equipment and
workplace properly for installation and service *
 Acquire manuals and service information required for installation
 Verify repair/maintenance history
 Conduct complete check-up of consumer electronic products and
systems, and identifies, verifies and documents defects against
customer description
 Test devices in accordance with standard procedures
 Install consumer electronic products and systems*
 Undertake final inspection
 Respond to unplanned events or conditions
 Clean and clear work site of all debris
 Prepare report on installation and testing of equipment
 Identify system defects/faults using appropriate tools and
equipment
 Diagnose faults and defects *
 Check and isolate circuits
 Explain identified defects and faults
 Check control settings/adjustments
 Document accurately results of diagnosis and testing
 Advise/inform customers regarding the status and serviceability
of the unit
 Replace defective parts/components with identical or recommended
appropriate equivalent ratings
 Maintain/Repair consumer electronic products *
 Use personal protective equipment
 Perform cleaning of unit

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 2
 Perform repair activity within the required timeframe
 Observe care and extreme precaution in handling the
unit/product
 Re-assemble and test repaired consumer electronic product *
 Subject reassembled units to final testing and cleaning
 Compile service completion procedures and
documentations
 Dispose waste materials
 Apply safety rules and procedures *

I agree to undertake assessment in the knowledge that information


gathered will only be used for professional development purposes and
can only be accessed by concerned assessment personnel and
manager/supervisor.

Date:
Candidate’s Name & Signature:

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 3
TESDA-OP-QSO-02-F07
Rev. No. 00-03/01/17
Reference No. EPA 1 9 0 9 8 3 1 3 4 0 0
to be filled out by the Processing Officer

SELF-ASSESSMENT GUIDE (PERFORMANCE ASSESSMENT)


ELECTRONICS PRODUCS ASSEMBLY AND
Qualification Title SERVICING NC II
SERVICE INDUSTRIAL ELECTRONIC MODULES,
COC 3 Title
PRODUCTS AND SYSTEMS
Instructions:
 Read each question in the left-hand column of the chart.
 Mark a check opposite each question to indicate your answer.

Can I? YES NO
 Prepare unit, tools and workplace for
installation/servicing*
 Acquire manuals and service information required for installation
 Verify repair/maintenance history
 Conduct complete check-up of consumer electronic products and
systems, and identifies, verifies and documents defects against
customer description
 Test devices
 Install industrial electronics systems/products *
 Undertake final inspection
 Respond to unplanned events or conditions
 Clean and clear work site of all debris
 Prepare report on installation and testing of equipment
 Identify system defects/faults using appropriate tools and equipment
 Test devices in accordance with standard procedures
 Diagnose faults of industrial electronics
systems/products*
 Check and isolate circuits
 Explain identified defects and faults
 Check control settings/adjustments
 Document accurately results of diagnosis and testing
 Advise/inform customers regarding the status and serviceability of
the unit
 Replace defective parts/components with identical or recommended
appropriate equivalent ratings
 Maintain/Repair industrial electronics products *
 Use personal protective equipment

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 4
 Perform cleaning of unit
 Perform repair activity within the required timeframe
 Observe care and extreme precaution in handling the unit/product
 Re-assemble and test repaired industrial electronics products *
 Subject reassembled units to final testing and cleaning
 Compile service completion procedures and documentations
 Dispose waste materials
 Apply safety rules and procedures *

I agree to undertake assessment in the knowledge that information


gathered will only be used for professional development purposes and
can only be accessed by concerned assessment personnel and
manager/supervisor.

Date:
Candidate’s Name &Signature:

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 5

You might also like