ICs for Audio Common Use

AN5277
Dual Channel SEPP Power Amplifier

■ Overview Unit : mm
The AN5277 is a monolithic integrated circuit designed 7.7±0.3

12
for 10.0 W (26 V, 8 Ω)output audio power amplifier. It is

(1.3)
a dual channel SEPP IC suitable for stereo operation in
TV application.

(10.0)
φ3.6

(1.27)
29.75±0.30
28.0±0.3
20.0±0.3

29.6±0.3
■ Features

0.6 –0.05 (1.27)

(10.0)
• Few external components :

+0.15
R1.8

• No Boucherot cells(output C, R)

0.6
• No Bootstrap Capacitors

0.25 –0.05 2.54

1

1.45±0.15
• No Negative Feedback Capacitors

+0.10
(12.5)
• Built-in muting circuit

3.5±0.3
1.2±0.1
• Built-in standby circuit

1.80±0.15
(1.2)

• Built-in various protection circuits (Load-short, thermal, 19.1±0.3

21.9±0.3

over-voltage and current)

• High ripple rejection(55 dB) HSIP012-P-0000A
• Compatible with AN5275, AN5276
• Operating voltage range 10 ∼ 32 V(26 V typ.)

■ Applications
• TV

■ Block Diagram

Protection circuit
Temperature
Over voltage
Att. Att. con Over current
Load short
Ripple
filter
10

Standby 11

12
1

GND 4

GND 9
N.C.

ch.1 In.

RF

(Input)

ch.2 In

N.C.

ch.2 Out

Mute

(Output)

VCC

ch.1 Out

1
AN5277 ICs for Audio Common Use

■ Pin Descriptions
Pin No. Description Pin No. Description
1 N.C. 7 ch.2 Output
2 ch.1 Input 8 Mute
3 Ripple Filter 9 Output GND
4 Input GND 10 VCC
5 ch.2 Input 11 Standby
6 N.C. 12 ch.1 Output

■ Absolute Maximum Ratings

Parameter Symbol Ratings Unit
Supply voltage VCC 35.0 V
Supply current ICC 4.0 A
Power dissipation *2 PD 37.5 W
Operating ambient temperature *1 Topr −25 to +75 °C
Storage temperature *1 Tstg −55 to +150 °C
Note) *1 : Ta = 25 °C except operating ambient temperature and storage temperature.
*2 : At Ta = 70 °C.

■ Recommended Operating Range

Parameter Symbol Range Unit
Supply voltage VCC 10.0 to 32.0 V

■ Electrical Caracteristics at VCC = 26 V, RL = 8 Ω, f = 1 kHz, Ta = 25 °C

Parameter Symbol Conditions Min Typ Max Unit
Quiescent current ICQ VIN = 0 mV  40 80 mA
Output end noise voltage *1 VNO No input,RG = 10 k  0.22 0..4 mV
Voltage gain GV VIN = 57 mV 32 34 36 dB
Total harmonic distortion *1 THD VIN = 57 mV  0.2 0.4 %
Maximum output power PO VCC = 26 V,THD = 10 % 8.0 10.0  W
Ripple rejection ratio *1 RR VR = 1 Vrms,fR = 120 Hz, RG = 10 kΩ, 45 55  dB
Channel balance CB VIN = 57 mV −1.0 0 1.0 dB
Muting ratio MR VIN = 57 mV 70 80  dB
Muting control voltage VMUTE VIN = 57 mV, MR≥70 dB 3.0   V
Standby control voltage 'on' VSTDON No input, ICC≤0.1 mA   5.0 V
Standby control voltage 'off' VSTDOFF No input, ICC≥20 mA 8.5   V
Channel crosstalk CT VIN = 57 mV,RG = 10 kΩ 50 60  dB
Note) *1 : For this measurement, use the 20 Hz to 20 kHz(12 dB/OCT) filter.

2
ICs for Audio Common Use AN5277

■ Terminal Equivalent Circuit

Pin No. Equivalent Circuit Description DC Voltage
1  Not connected 
2 ch.1 Input : 0V

Pin2 200 Ω 400 Ω This is the amplifier input pins.

5

30 kΩ

3 Ripple Filter : VCC − 1.5 VBE

10 This is the pin to connect the positive
terminal of a ripple filter capacitor.

30 kΩ
3
20 kΩ

15 kΩ

15.7 kΩ

4  Input GND : 0V
Input ground pin.
5 Refer to Pin2 ch.2 Input : 
This is the amplifier input pins.
6  Not connected 
7 ch.2 Output : VCC/2
10
ch.2 output pin

Driver Cct
Pre-amp.
7

600 Ω 30 kΩ 9

VCC/2

3
AN5277 ICs for Audio Common Use

■ Pin Equivalent Circuit (continued)

Pin No. Equivalent Circuit Description DC Voltage
8 Mute : 
10 Mute input pin.
Mute 'On' = 5 V
Mute 'Off' = 0 V

3 kΩ 3 kΩ

10 kΩ
8
200 Ω

9  Output GND : 0V
ch.1 & ch.2 output ground.
10  VCC : typ. : 26 V
This is the power supply pin.
11 10 Standby : 
This is the standby control pin.

11

5 kΩ
5 kΩ

3 kΩ

12 10 ch.1 Output : VCC/2

ch.1 output pin

Driver Cct 12
Pre-amp.

600 Ω 30 kΩ 9

4
ICs for Audio Common Use AN5277

■ Application Circuit Example

VCC

100 µF

VCC
3 R.F.
1 000 µF

10
VCC
STB Off 11
STB On STB

1 µF
VIN1 2
1 000 µF
12
10 kΩ
SP
8Ω

1 000 µF
7
1 µF
VIN2 5
SP
10 kΩ 8Ω

5V
Mute On 8.2 kΩ Mute 8

Mute Off
10 µF 9
Output GND
1

6
N.C.

N.C.

STB 'Off' VCC

Input
GND

STB 'On' 0V
Mute 'Off' 0V
Mute 'On' 5V

■ Usage Notes
1. External heatsink is needed when used. External heatsink should be fixed to the chassis.
2. Fin of the IC can be connected to GND.
3. Please prevent output to VCC short and output toGND short.
4. Load short protection will only prevent the IC from damaging if operating VCC<30 V
5. The temperature protection circuit will operate at Tj around 150 °C.
However, if temperature decrease, the protection circuit will automatically be deactivated and resume
normal operation.

5
AN5277 ICs for Audio Common Use

■ Technical Information
• PD  Ta Curves of HSIP012-P-0000A
PD  Ta

80

70

Power dissipation PD (W)

62.5 W
60

50
(1)

40

30

20.8 W
20
15.6 W (2)
(3)
10
3.0 W (4)
0
0 25 50 75 100 125 150

Ambient temperature Ta (°C)

1. TC = Ta,62.5 W(θj-c = 2 °C/W)

2. 20.83 W(θf = 4.0 °C/W)
With a 100 cm2 X 3 mm Al heat sink(black
colour coated)or a 200 cm2 X 2 mm Al
heat sink(not lacquered)
3. 15.63 W(θf = 6.0 °C/W)
With a 100 cm2 X 2 mm Al heat sink(not
lacquered)
4. 3.0 W at Ta = 25 °C(θj-a = 42 °C/W)
Without heat sink

6
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.

Please read the following notes before using the datasheets

A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may ap-
pear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.

2001 MAR
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.