SERIES[§

5500

LED TV
user manual

Thank you for purchasing this Samsung product.

To receive more complete service, please register
your product at
www.samsung .com/register
Model _ __ _ _ Serial No. _ __ _ _

"% If you have any questions, please call us at 1-800-SAMSUNG (1 -800-726-7864) for assistance.

Downloaded from www.Manualslib.com manuals search engine

 Important Safety Instructions

This symbol indicates that high voltage is

present inside. It is dangerous to make any kind
of contact with any internal part of this product
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). THERE ARE NO USER This symbol indicates that important literature
concerning operation and maintenance has
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
been included with this product
QUALIFIED PERSONNEL.

• The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of this
apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered.
- Do not place this apparatus in a confined space. such as a bookcase, or built-in cabinet, unless proper ventilation is provided.
- Do not place this apparatus near or over a radiator or heat register, or where it is exposed to direct sunlight
- Do not place vessels (vases etc.) containing water on this apparatus, as this can result in a fire or electric shock.
• Do not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or
near a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately.
• This apparatus uses batteries. In your community, there might be environmental regulations that require you to dispose of these batteries
properly. Please contact your local authorities for disposal or recycling information.
• Do not overload wall outlets, extension cords or adaptors beyond the1r capacity, since this can result in fire or electric shock.
• Power-supply cords should be placed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords at the plug end, at wall outlets, and the point where they exit from the appliance.
• To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the
local electrical supply.
• Never insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock.
• To avoid electnc shock, never touch the 1nside of this apparatus. Only a qualified technician should open this apparatus.
• Make sure to plug the power cord in until it is firmly seated. When unplugging the power cord from a wall outlet, always pull on the power
cord's plug. Never unplug by pulling on the power cord. Do not touch the power cord with wet hands.
• If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately
and contact an authorized dealer or service center.
• Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time
(especially when children, elderly or disabled people will be left alone in the house).
- Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate sparks and heat or
the insulation to deteriorate.
• Be sure to contact an authorized service center for information if you intend to install your TV in a location with heavy dust, high or low
temperatures, high humidity, chemical substances, or where it will operate 24 hours a day such in an airport, a train station, etc. Failing to
do so may lead to serious damage of your TV.
• Use only a properly grounded plug and wall outlet
- An Improper ground may cause electric shock or equipment damage. (Class I Equipment only.)
• To turn this apparatus off completely, you must disconnect it from the wall outlet Consequently, the wall outlet and power plug must be
readily accessible at all times.
• Do not allow children to hang onto the product
• Store the accessories (battery, etc.) in a location safely out of the reach of children
• Do not install the product in an unstable location such as a shaky self, a slanted fioor or a location exposed to vibration.
• Do not drop or apply any shock to the product II the product is damaged, disconnect the power cord and contact a service center.
• To clean this apparatus, unplug the power cord from the wall outlet and wipe the product using a soft, dry cloth. Do not use any chemicals
such as wax, benzene, alcohol, thinners, Insecticide, air fresheners, lubricants, or detergent These chemicals can damage the appearance
of the TV or erase the printing on the product
• Do not expose this apparatus to dripping or splashing.
• Do not dispose of batteries in lire
• Do not short-circuit, disassemble or overheat the batteries.
• There is danger of an explosion if you replace the batteries used in the remote with the wrong type of battery. Replace
only with the same or equivalent type.
• WARNING - TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.

Downloaded from www.Manualslib.com manuals search engine

 Contents

Basic Features Troubleshooting and Other

5 Using the Remote Control
Information
6
15 Troubleshooting
7 Turning on the TV
16 Mounting the TV on the Wall Using
8 Switching Between Video Sources
the Wall Mount Kit (Optional)
9 Universal Remote Control Setup
18 Assembling the Cable manager

18 Eco Sensor and Screen Brightness

19 Maintenance

Viewing the e-Manual 19 Providing Proper Ventilation for Your TV

10 Viewing the e-Manual

20 Securing the TV to the Wall

10 Scrolli!l[1 a Page
10 Usin~~ Top Icons
-1! n Pc,t' ..._,........ the. 1-i
+,n ! 'r-,rr' ,e· Page-
'\.._) I 'rn
1t _.. i.J : ! i\: \._.; u 1 • 1 , '-
Specifications
10 Searching the Index
-:1 Searching r:>ages 21 Specifications
11 1 (~!nc)i n c~ +r-,e P - f\1J1;m
,, ·'c_j
...._,.. , \...~~- l. l v ! , ,~,'

22 Dimensions
1 ·1 Jur--r-1 ng to a 1\!ienu itern
11 Updat1ng the e-1\!ianual 22 Licenses

Network Configuration Guides

12 Connecting to a Network 23 Warranty Information
12 Nk:=>t'
'-' \,._
',/(-,,.-1<
,_,) , t CnnrJ;:::or---~~--,
,_)~ ' . . ._, .. __.. . ' \..,j
nn ! '
25 SAMSUNG BRAND PRODUCTS

12 VVireiess i\Jetwork
25 Lli\!iiTED VVf\RRANTY TO
OFiiGNAL. PURCHASER
1 2 1\Jetwork Secunty Protocols
I'~),
1 \...../
['\l1e-- -tlt-v'ork Corli"'lr:)c··tl' r\n - \)\/ired
- · ·· !,, 1 . '-...-' /,. ~ , : ~ ··

14 What is Remote Support?

Downloaded from www.Manualslib.com manuals search engine

 Figures and illustrations in this User Manual are provided for reference only and may differ from the actual
product appearance. Product design and specifications may change without notice.

Features of your new 1V

• SMART HUB:
This TV features Smart Hub, a multi-purpose entertainment and family center. With Smart Hub, you
can surf the web, download applications, and stay in touch with family and friends through social
networking services. In addition, you can view or play photo, video, and music files stored on external
storage devices.
Press 8 to launch Smart Hub. Choose a service using the icons displayed in the top part of the screen.
Smart Hub services and functionality include:
Social: Watch the latest YouTube videos and you and your friends video posts on Facebook and
Twitter. You can also make video calls to friends by connecting the TV to a camera (sold separately).
Apps: Samsung Apps offers an extensive collection of free and paid news, sports, weather, and
gaming content you can directly download to and enjoy on your TV.
On TV: Check a listing of programs that are currently airing or are scheduled to air.
Movies & TV Shows: Purchase and watch movies and series without a separate external device.
Photos, Videos & Music: Play back photo, video, and music files from an external storage device.

• Anynet+ (HDMI-CEC): This allows you to control all connected Samsung devices that support
Anynet+ with your Samsung TV's remote.

• e-Manual: Provides a detailed, on-screen user's manual built into your TV.

• SMART Interaction: Using this function, you can access and control menu options and functions
using motions. To use the Smart Interaction Feature, connect the SMART TV camera (sold separately)
to your TV.

• Device Manager: Use the TV features with a USB keyboard and mouse.

• Screen Mirroring: Displays mobile device screens on your TV using a wireless connection.

Downloaded from www.Manualslib.com manuals search engine

 Using the Remote Control
Learn where the function buttons are on your remote. Especially note these: SOURCE, MUTE, VOL, CH,
MENU, TOOLS, G', INFO, CH LIST, RETURN, and EXIT.
~ This remote control has Braille points on the Power, Channel, and Volume buttons and can be used
by visually impaired persons.

Displays and selects the available video

sources.
Turns the TV on and off. .....,:.....:..__ _ STB: Turn on and off the satellite or cable
set-top box connected to the TV.
STB GUIDE: Displays the STB's EPG
Turn on the backlight for the buttons. -----:~-1
(Electronic Program Guide).
The backlight lasts for only a few seconds. STB MENU: Opens the STB's OSD (Menu).
Turns the remote control light on or off.
~ These buttons are only available when
When on, the buttons become illuminated
for a moment when pressed. (Using the L:!_Jl2_j l2J the universal remote control is set and
TV turns on.

000
remote control with this button set to On
will reduce the battery usage time.)

Gives direct access to channels.

Press to select additional digital channels

JJ000
8 0 (
-----=-..:...._
1

PRE-CH J---:--:-- - - Returns to the previous channel.

being broadcast by the same digital station.
For example, to select channel '54-3', press
'54', then press'-' and '3'.
+ 11
~ Cuts off the sound temporar;>;.

Adjusts the volume. ~ I ~ ~ LJl__ Changes channels.

CH

v
Displays channel lists on the screen. _ ____:~----' ::===~W---- Brings up Smart Hub applications. See the
e-Manual chapter, Smart TV Features >
Opens the OSD (Menu). Smart Hub.

--:-:---- Displays the EPG (Electronic Program

Guide).
Quickly selects frequently used functions.
Displays information on the TV screen.

Moves the cursor, selects the on-screen ------;.....;....-1

menu items, and changes the values seen
on the TV's menu.
Returns to the previous menu. Exits the menu.

Use these buttons according to the

directions on the TV's screen.

Use these buttons in a specific feature.

Use these buttons according to the
directions on the TV's screen.

SI\MSUNG

Downloaded from www.Manualslib.com manuals search engine

 Inserting the Batteries (AAA X 2)
Match the polarity of the batteries to the symbols in the battery compartment.

•
r.:-~~
•

~- f. .
' ··.0 "'~~~
~~~~
' ~ J

~NOTE

- Use the remote control within 23 feet of the TV.

- Bright light may affect the performance of the remote control. Avoid using when near special
fluorescent lights or neon signs.
- The color and shape may vary depending on the model.

Downloaded from www.Manualslib.com manuals search engine

 Turning on the TV
Turn on the TV using the C) button on the remote control or TV panel.
~ The product color and shape may vary depending on the model.
~ The first time you turn on your TV, it will immediately start the initial setup.
~ The TV's Controller, a small joy stick like button on the rear right side of the TV, lets you control the TV
without the remote control.

Open Smart Hub.

Open the menu. Select a source.

Turn off the 1V.

• ------------ "fh"e"coniroi stick is-~~~a~i~~~~-r·o·--------- "j

lower-left corner on the back of the TV. : ~ :
'
'
~ '
'
' - - - Remote control sensor :, ___________ :
When you use the Remote control, the
standby LED does not respond, except
when you press the 6 button.

Caution of the cover-jack

lL CAUTION
The cover-jack is for use by qualified service personnel only.
To reduce the risk of electric shock or fire hazard, do not use the cover jack, unless you are qualified to do
so.

TV Rear Panel

~ The rear panel may differ depending on the model.

Downloaded from www.Manualslib.com manuals search engine

 Switching Between Video Sources
Press the SOURCE button to switch between devices connected to the 1V.
For example, to switch to a game console connected to the second HDMI connector, press SOURCE
button. From the Source list, select HDMI2. The connector names may vary depending on the product.
Select Tools at the upper-right corner of the source screen to access the following functions.

• Edit Name: Lets you associate a device name to an input source.

You can select the following device names in the Edit Name option:
VCR I DVD I Cable STB I Satellite STB I PVR STB I AV Receiver I Game I Camcorder I PC I DVI
PC I DVI Devices I TV I IPTV I Blu-ray I HD DVD I DMA
To associate a device name to an input source follow these steps:
1. Select Tools in the upper right corner of the source screen.
2. Select Edit Name.
3. Find the input source you want in the Source list (HDMI1, HDMI2, Component, etc.).
4. Select the blank field next to the input.
5. In the device name list that appears, select the name of the device attached to the input.
When you view the Source list, the device name and the input jack will be displayed together.
- If you have connected a PC to the HDMIIN 3 (DVI) port with an HDMI cable, select PC from the
device name list.
- If you have connected a PC to the HDMIIN 3 (DVI) port with an HDMI to DVI cable, select DVI PC
from the device name list.
- If you connected an AV device to the HDMIIN 3 (DVI) port with an HDMI to DVI cable, select DVI
Devices from the device name list.

• Information: View detailed information about the connected devices.

• Refresh: Select if a connected device does not appear in the list. If the list does not show the device
after selecting Refresh , check the status of the 1V-to-device connection.

• Remove USB: Remove the USB device from the list safely. This function is only available when the
USB device selected.
Universal Remote Setup: Use to configure universal remote control settings. Using the universal remote
control, you can control external devices connected to the 1V, such as a set-top box, Blu-ray player, and
AV receiver.

:-:; : ,_. ' ~··? :~~"'~'•'c:;'' '-<~'''; :·

Downloaded from www.Manualslib.com manuals search engine . .
 Universal Remote Control Setup
This 1V has a universal remote control feature that lets you control cable boxes, Blu-ray players, home
theaters, and other third-party external devices connected to the 1V using the 1V's remote control.

~,

,,,""' ........... ,,
' ''
I '' ' \
I

~
I

I
I
I
I
\ I
I
I
,,,,''' I
I
I
I
I
I
I
I
I

,/
.... __ ___ ... ,,'

Keep a distance of 2 inches at least between the IR Extender and the external device, as the illustration
shows. Face the IR Extender toward the external device's remote control signal receiver. Note that it should
be no obstacle between IR Extender and external device. The presence of an obstacle will interfere with
the transmission of the remote control signal.

Add the External Device

1. Turn on the external device you wish to set up universal remote function for and then press SOURCE
to bring up the Source screen.
2. Select Universal Remote Setup from the top of the screen. This initiates the universal remote setup
process.
3. Follow the on-screen instruction and set up the universal remote control. If it does not work, set up the
remote control by entering the model number manually.

Downloaded from www.Manualslib.com manuals search engine

 Viewing thee-Ma nual
The embedded e-manual contains information about your 1V's key features.
Navigate to the screen menu and select e-Manual (Support > e-Manual).
1. Select a category from the left side of the screen.
2. Select an item. Thee-Manual will open on the page containing the selected information.
~ Words in blue refer to screen menu options and words in light blue refer to remote control buttons.

~ Arrows are used to indicate the menu path. (Example: Screen Menu > Support > e-Manual)

Scrolling a Page
To scroll a page, use of one of the following methods:

• Place the focus on the • or • button at the right edge of the screen.

• Place the focus on the .oil. or ~ button at the right edge of the screen, press the up or down arrow
button on the remote.

Using the Top Icons

Use the Back, Forward , and Opened pages icons on the top left of the screen to navigate through
pages. These icons are available after you have viewed two or more pages.

Returning to the Home Page

To return to the home page, press the rJ button or select .ft. on the top right of the screen.
Searching the Index
Press the mbutton or select ..1. on the top right of the screen to display the index. Select a term to display
the page containing the term.

Downloaded from www.Manualslib.com manuals search engine

 Searching Pages
Press the [!I button or select .Cl... on the top right of the screen , and enter search criteria. Select a page
from the list of search results to display it.

Closing the e-Manual

To close thee-Manual, press hold the RETURN button or select X at the upper-right corner of the
screen.

Jumping to a Menu Item

To jump directly to the menu item that is described in the current section, select Ci~~lJ It is possible
to jump from a menu item directly to the related section in thee-Manual. On the screen menu, press the
E-MANUAL button that appears on the screen.
~ This feature may not be available, depending on the menu.

Updating the e-Manual

Open the Smart Hub and select Apps, and then select More Apps. The e-manual can be updated in the
same way with an application update.
On the More Apps screen, select Update Apps . Select e-Manual from the list. The e-Manual starts
updating to the latest version.

Downloaded from www.Manualslib.com manuals search engine

 Connecting to a Network
Connecting the TV to a network gives you access to online services such as Smart Hub and lets you
update the TV's software online directly from Samsung.com.

Network Connection - Wireless

Connect the TV to the Internet using a standard wireless router or modem.

Wireless IP Router or Modem

that has a DHCP Server
-- - -··-=------ -
The LAN Port on the Wall

((< ; I

LAN Cable (Not Supplied)

Wireless Network Precautions

• This TV supports the IEEE 802.11 a/b/g /n communication protocols. Samsung recommends using
IEEE 802.11 n. Otherwise, when you play video over a network connection, the video may not play
smoothly.

• To use a wireless network, the TV must be connected to a wireless router or modem. If the wireless
router supports DHCP, the TV can use a DHCP or static IP address to connect to the wireless network.

• Select a channel that is not currently in use for the wireless router. If the channel set for the
wireless router is currently being used by another device, the result is usually interference and/or a
communications failure.

• Most wireless networks have an optional security system. To enable a wireless network's security
system, you need to create a security key using characters and numbers, and then enter that key into
the router through its menu. You then must enter this security key into any other devices you want to
connect to the wireless network.

Network Security Protocols

The TV only supports the following wireless network security protocols:

• Authentication Modes: WEP, WPAPSK, WPA2PSK

• Encryption Types: WEP, TKIP, AES

In compliance with the newest Wi-Fi certification specifications, Samsung TVs do not support WEP or TKIP
security encryption in networks running in the 802.11 n mode.
If the wireless router supports WPS (Wi-Fi Protected Setup), you can connect the TV to your network using
PBC (Push Button Configuration) or a PIN (Personal Identification Number). WPS automatically configures
the SSID and WPA key settings.
Your Smart TV cannot connect to uncertified wireless routers.

Downloaded from www.Manualslib.com manuals search engine

 Network Connection - Wired
There are three main ways to connect your TV to your network using cable, depending on your network
setup. They are illustrated below:

TV Rear Panel
The Modem Port on the Wall External Modem
(ADSL I VDSL I Cable TV)

Modem Cable (Not Supplied) LAN Cable (Not Supplied)

TV Rear Panel
The Modem Port on the Wall External Modem
IP Router that has a
(ADSL I VDSL I Cable TV) DHCP Server

Modem Cable LAN Cable LAN Cable

(Not Supplied) (Not Supplied) (Not Supplied)

TV Rear Panel
The LAN Port on the Wall

LAN Cable (Not Supplied)

~ The TV does not support network speeds less than or equal to 10Mbps.
·~ Use Cat 7 cable for the connection.

Downloaded from www.Manualslib.com manuals search engine

 What is Remote Support?
Samsung Remote Support service offers you one-on-one support with a Samsung Technician who can
remotely.

• Diagnose your TV

• Adjust the TV settings for you

• Perform a factory reset on your TV

• Install recommended firmware updates

How Does it Work?

Having a Samsung Tech remotely service your TV is easy.

~--.........,.,..,~ , l

l__...... · .· .;_• ..••. ~,

.!'
-
.. ·' .··
. .

~ ' ' ' "

1 . Call the Samsung 2. Open the menu 3. Select Remote 4. The agent will then
Contact Center on your TV and Management and access your TV.
and ask for remote go to the Support Provide the Pin# to That's it!
support. section. the agent.

Downloaded from www.Manualslib.com manuals search engine

 Troubleshooting
If the TV seems to have a problem, first review this list of possible problems and solutions. Also, review
the Troubleshooting Section in thee-Manual. If none of the troubleshooting tips apply, visit www.samsung.
com/support or call Samsung Customer Service at 1-800-SAMSUNG (1 -800-726-7864).

Flickering and Dimming If your Samsung Television is flickering or dimming sporadically, you may need to d1sable some of the
energy efficiency features.
Disable Energy Saving (System > Eco Solution > Eco Sensor) and/or Energy Saving (System > Eco
Solution > Energy Saving) and check again.
Component Connections /Screen Color If you find that the color on your Samsung television screen 1s not correct or the black and white colors
are off, run a Self Diagnosis Picture Test (Support > Self Diagnosis > Picture Test).
If the picture problem is caused by the TV, the problem should be visible in the Picture Test. If the problem
is not visible, next confirm that the TV's video input jacks are connected to the correct external video
device output jacks and that none of the connections are loose. Finally, if possible, test your external video
devices by connecting them to another TV.

Screen Brightness If you find that the colors on your Samsung TV are correct but just a little too dark or bright, try adjusting
the following settings first.
Navigate to Picture and adjust Backlight, Contrast, Brightness, Sharpness, Color, Tint (G/R) and
other picture quality adjustment sett1ngs.
Unwanted Powering Off If your Samsung TV appears to turn off by itself, try disabling some of the TV's energy efficiency and
automatic off features. Check if Sleep Timer (System > Time > Sleep Timer) has been enabled. Sleep
Timer automatically turns off the TV after an amount of t1me that you select. If the Sleep Timer has not
been enabled, see if No Signal Power Off (System > Eco Solution > No Signal Power Off) or Auto
Power Off (System > Eco Solution > Auto Power Off) has been enabled. No Signal Power Off turns
off the TV if no signal has been received by the TV for a specified period time. Auto Power Off turns off
the TV if there has been no user input in four hours.
Trouble Powering On When the TV is turned on, the remote control receiver flashes 5 times before the screen turns on.
If you f1nd that you are having problems powering on your Samsung television, there are a number of
things to check before calling the service department.
If the power cord is connected properly and the remote control is operating normally, the problem might
be with the antenna cable connection or the cable/satellite box not being turned on. Check the antenna
connection or turn on the cable/satellite box.
Stand Assembly If you have any trouble assembling the stand, review the stand assembly instruction in the Quick Start
Guide.
Cannot Find a Channel Re-run Setup (Go to Menu > System > Setup) or run Auto Program. (Go to Menu > Broadcasting >
Auto Program).

~ For detailed troubleshooting information, watch the troubleshooting videos at www.samsung.com/

spsn.

Downloaded from www.Manualslib.com manuals search engine

 The TV won't turn on. • Make sure the AC power cord is securely plugged 1n to the wall outlet and the TV.
• Make sure the wall outlet is working.
• Try pressing the 6 button on the TV to make sure the problem is not the remote. If the TV turns on,
refer to "Remote control does not work" below.

There is no picture/video. • Check the cable connections. Remove and reconnect all cables connected to the TV and external
devices.
• Set the video outputs of your external devices (Cable/Sat Box, DVD, Blu-ray etc) to match the TV's
input connections. For example, if an external device's output is HOMI, it should be connected to an
HOM I input on the TV.
• Make sure your connected devices are powered on.
• Be sure to select the correct input source.
• Reboot the connected device by unplugging it, and then reconnecting the device's power cable.
The remote control does not work. • Replace the remote control batteries. Make sure the batteries are installed with their poles (+/-) in the
correct direction.
• Clean the sensor's transmission window on the remote.
• Try pointing the remote directly at the TV from 5- 6 feet away.
The cable/set top box remote control • Program the Cable/Set remote control to operate the TV. Refer to the Cable/Set-Top-Box user
doesn't turn the TV on or off or adjust the manual for the SAMSUNG TV code.
volume.
~ This TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to
produce. There may be, however, a few bright or dark pixels on the screen. These pixels will have no
impact on the performance of the product.
~ To keep your TV in optimum condition, upgrade to the latest software. Use the Update Now or Auto
Update functions on the TV's menu (Screen Menu > Support > Software Update > Update now or
Screen Menu > Support > Software Update > Auto Update).

Mounting the lV on the Wall Using the Wall Mount Kit

(Optional)
Wall or Ceiling Mounting
If you mount this product on a wall, it should be mounted only as recommended by the
manufacturer. Unless it is correctly mounted, the product may slide or fall, causing serious
injury to a child or adult, and serious damage to the product.

Installing the Wall Mount Kit

The wall mount kit (sold separately) lets you mount the TV on the wall.
For detailed information about installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket. We do not
advise you to do it yourself. Samsung Electronics is not responsible for any damage to the product or injury
to yourself or others if you elect to install the wall mount on your own .
To order the wall mount kit, contact Samsung Customer Care at 1-800-SAMSUNG (1 -800-726-7864).

Downloaded from www.Manualslib.com manuals search engine

 Installing a Wall Mount using the Wall mount adapter

~ For more detailed information, refer to the User

Manual of the Wall Mount Kit.
~ Wall mount adapters are provided only with 46-inch
or bigger TVs.

VESA Wall Mount Kit Notes and Specifications

~ Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to
surfaces other than plaster board, please contact your nearest dealer for additional information. If you
install the TV on a ceiling or slanted wall, it may fall and result in severe personal injury.
~ NOTE

• Standard dimensions for wall mount kits are shown in the table below.
• Samsung wall mount kits contain a detailed installation manual , and all parts necessary for
assembly are provided.
• Do not use screws that do not comply with VESA standard screw specifications.
• Do not use screws that are longer than the standard length or do not comply with VESA standard
screw specifications. Screws that are too long may cause damage to the inside of the TV set.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the
screws may differ depending on the wall mount specifications.
• Do not fasten the screws too firmly. This may damage the product or cause the product to fall,
leading to personal injury. Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified
wall mount is used or the consumer fails to follow the product installation instructions.
• Do not mount the TV at more than a 15 degree tilt.
• Always have two people mount the TV on to a wall.

19 - 22 75 X 75
M4
28 100 X 100
LED-TV
4
[Slim]
32 - 42 200X 200
M8
46 - 65 400 X 400

Do not install your Wall Mount Kit while your TV is tu rned on. It may result in personal
injury from electric shock.

Downloaded from www.Manualslib.com manuals search engine

 Assembling the Cable manager

Eco Sensor and Screen Brightness

..
Eco Sensor measures the light in your room and optimizes the brightness of the 1V automatically to red uce
power consumption. This causes the 1V to brighten and dim automatically. If you want to turn this function
off, go to Menu > System > Eco Solution > Eco Sensor

Do not block the sensor with any material. It can decrease picture brightness.

Downloaded from www.Manualslib.com manuals search engine

 Maintenance
~ If a sticker was attached to the TV screen, some debris can remain after you remove the sticker.
Please clean the debris off before watching TV.
~ The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior
and screen carefully using a soft cloth to prevent scratches.

·Fl-Y.'water directly ooto 'the prod!Jct. &r;ly. Clean tt:te,product with a,::;oft c),atM dampen~<;i with
g6esJnto th€{prod'O'c f may cilUse a ' Y ', a small 'c:lfnot.fnt
of water.'~o6 'n'ot a
use fl~fflm~ble ~ . ..
e, or electric shock. ··· > liquid (e.g. benzene, thinners) or: a ;cleaning agent

Providing Proper Ventilation for Your TV

When you install your TV, maintain a distance of at least 4 inches between the TV and other objects (walls,
cabinet sides, etc.) to ensure proper ventilation. Failing to maintain proper ventilation may result in a fire or a
problem with the product caused by an increase in its internal temperature.
~ Whether you install your TV using a stand or a wall-mount, we strongly recommend you use parts
provided by Samsung Electronics only.
• If you use parts provided by another manufacturer, it may cause difficulties with the product or result
in injury caused by the product falling.

lnstatiatl<>n with astanct .. tn~tallation witti'a wall~mount.

-- ---------- -r--4 -----------
: inches :
:------------r4 i~c-h~~ - - - - - -:

I
I
I
I
: :

-r-
4 inches : 4 inches : : 4 inches

rr-
: 4 inches
~ I
~
I 1
I I
I I
I I
I I I

I
I :______ __ ____ _I_~ Ln<;:~E)S__ ____ ~

Other Warnings
~ The actual appearance of the TV may differ from the images in this manual, depending on the model.
~ Be careful when you touch the TV. Some parts can be warm or hot.

Downloaded from www.Manualslib.com manuals search engine

 Securing the TV to the Wall

Caution: Pulling, pushing, or climbing on the TV may cause the

TV to fall. In particular, ensure your children do not hang on or
destabilize the TV. Doing so may cause the TV to tip over, causing
serious injuries or death. Follow all safety precautions provided
in the Safety Flyer included with your TV. For added stability
and safety, you can purchase and install the anti-fall device as
described below.

To Avoid the TV from Falling

1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been
firmly installed onto the wall.
~ You may need additional material such as an anchor depending on the type of wall.
~ Since the necessary clamps, screws, and string are not supplied, please purchase these
additionally.
2. Remove the screws from the back center of the 1V, put the screws into the clamps, and then fasten the
screws onto the 1V again.
~ Screws may not be supplied with the product. In this case,
please purchase the screws of the following specifications.
~ Screw Specifications
• For a 19- 28 inches: M4
• For a 32 - 65 inches: M8
3. Connect the clamps fixed onto the 1V and the clamps fixed onto
the wall with a strong cable and then tie the string tightly.
~ NOTE

Install the 1V near to the wall so that it does not fall backwards.
..············...
It is safe to connect the string so that the clamps fixed on the
wall are equal to or lower than the clamps fixed on the 1V. ....:·~· .
.·".. ..~
.
Untie the string before moving the 1V.
······· .·
4. Verify all connections are properly secured. Periodically check the
connections for any sign of fatigue or failure. If you have any doubt
about the security of your connections, contact a professional
installer.

Downloaded from www.Manualslib.com manuals search engine

 Specifications

Environmental Considerations
Operating Temperature 50°F to 104°F (10°C to 40°C)
Operating Humidity 10% to 80%, non-condensing
Storage Temperature -4' F to 113°F (-20'C to 45'C)
Storage Humidity 5% to 95%, non-condensing

Screen Size
(Diagonal)

10Wx2
Dimensions 0N x H x D)
Body 29.0 x 17.5 x 1.9 inches 36.5 x 21.7 x 1.9 inches
(738.0 x 445.4 x 49.0 mm) (9282 x 552.3 x 49.4 mm)
With stand 29.0 x 20.0 x 10.4 inches
.0 X 509.6 X 265.0
Weight
Without Stand 11.0 lbs (5.0 kg)
With Stand

10Wx2
Dimensions ryv x H x D)
Body 41.7 x 24.6 x 1.9 inches 44.7 x 26.2 x 1.9 inches
(1059.6 x 626.2 x 49.4 mm) (11 35.4 x 668.0 x 49.8 mm)
With stand 41.7 x 27.5 x 12.0 inches 44.7 x 29.2 x 12.0 inches
(1 059.6 x 700.0 x 307.3 mm) (1135.4 x 741.8 x 307.3 mm)
Weight
Without Stand 23.8 lbs (10.8 kg) 28.6 lbs (13.0 kg)
With Stand 27.31bs 32.1 lbs 4.6
~ Design and specifications are subject to change without prior notice.
~ The actual appearance of the TV may differ from the images in this manual, depending on the model.
~ This device is a Class B digital apparatus.
~ For information about the power supply, and more information about power consumption, refer to the
label attached to the product.
~ Typical power consumption is measured according to Energy Star Program requirements for
Televisions.

Dispose unwanted electronics through an approved recycler.

To find the nearest recycling location, go to our website:
www.samsung.com/recyclingdirect or call, (877) 278 - 0799

Standby mode

To decrease power consumption, unplug the power cord when you don't intend to use the TV for a long
time.

Downloaded from www.Manualslib.com manuals search engine

 Dimensions
• Jack panel detail I Rear view

(Unit: inches)
~ The displayed image may differ depending on the model.

.,.. Moqe) ~ame . , m It' . @i;;> ,{;,'-''·· ®r

·.. · .\ .·•
m •c,·
.® :cc;••. JID ,/.v./
UN32F5500 7.8 4.8 4.0 19. 1 7.8 7.8
UN40F5500 9.8 6.9 6.2 24.4 7.8 7.8
UN46F5500 12.1 6.4 6.9 30. 1 15.7 15.7
UN50F5500 14.0 6.8 6.6 32.7 15.7 15.7
NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior
notice. Refer to the dimensions before installing your TV. Not responsible for typographical or printed errors.
© 2013 Samsung Electronics America, Inc

Licenses

[I] DOLBY.
DIGITAL PLUS I ~db ~db
Premium Sound 15.1 Studio Sound
PULSE I

DIVX:
HD
.

Downloaded from www.Manualslib.com manuals search engine

 Warranty Information
Federal Communication Commission FCC Radiation Exposure Statement:
Interference Statement This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
This equipment has been tested and found environment. This equipment should be installed
to comply with the limits for a Class B digital and operated with minimum distance 20cm
device, pursuant to Part 15 of the FCC Rules. between the radiator & your body.
These limits are designed to provide reasonable
protection against harmful interference in a
This Class 8 digital apparatus complies
residential installation. This equipment generates,
uses and can radiate radio frequency energy with Canadian ICES-003.
and, if not installed and used in accordance with
the instructions, may cause harmful interference
Cet appareil numerique de Ia classe B conforme a
Ia norme NMB-003 du Canada.
to radio communications. However, there is no
guarantee that interference will not occur in a This device complies with Industry Canada license-
particular installation. If this equipment does cause exempt RSS standard(s). Operation is subject to
harmful interference to radio or television reception, the following two conditions: (1) this device may not
which can be determined by turning the equipment cause interference, and (2) this device must accept
off and on, the user is encouraged to try to correct any interference, including interference that may
the interference by one of the following measures: cause undesired operation of the device.
Le present appareil est conforme aux CNR
• Reorient or relocate the receiving antenna.
d'lndustrie Canada applicables aux appareils radio
• Increase the separation between the equipment exempts de licence. L'exploitation est autorisee
and receiver. aux deux conditions suivantes: (1) I' appareil ne
doit pas produire de brouillage, et (2) l'utilisateur
• Connect the equipment into an outlet on a de I' appareil do it accepter tout brouillage
circuit different from that to which the receiver is radioelectrique subi, meme si le brouillage est
connected. susceptible d'en compromettre le fonctionnement.
For product available in the USA/Canada market,
• Consult the dealer or an experienced radio/TV
only channel 1-11 can be operated. Selection of
technician for help.
other channels is not possible.
FCC Caution: Any changes or modifications not
This device and its antenna(s) must not be co-
expressly approved by the party responsible for
located or operation in conjunction with any other
compliance could void the user's authority to
antenna or transmitter.
operate this equipment.
Under Industry Canada regulations, this radio
This device complies with Part 15 of the FCC
transmitter may only operate using an antenna
Rules. Operation is subject to the following two
of a type and maximum (or lesser) gain approved
conditions: (1) This device may not cause harmful
for the transmitter by Industry Canada. To reduce
interference, and (2) this device must accept any
potential radio interference to other users, the
interference received, including interference that
antenna type and its gain should be so chosen that
may cause undesired operation.
the equivalent isotropically radiated power (e.i.r.p.)
For product available in the USA/Canada market, is not more than that necessary for successful
only channel 1-11 can be operated. Selection of communication.
other channels is not possible.
IC Radiation Exposure Statement:
This device and its antenna(s) must not be co-
This equipment complies with IC RSS-1 02 radiation
located or operation in conjunction with any other
exposure limits set forth for an uncontrolled
antenna or transmitter.
environment. This equipment should be installed
and operated with minimum distance 20cm
between the radiator & your body.

Downloaded from www.Manualslib.com manuals search engine

 IMPORTANT WARRANTY INFORMATION The above described warranty repairs must be
REGARDING TELEVISION FORMAT performed by a SAMSUNG Authorized Service
Center. Along with this Statement, the Original
VIEWING
Limited Warranty Statement and a dated Bill of
~ See the warranty card for more information on Sale as Proof of Purchase must be presented
warranty terms. to the Service Center. Transportation to and
from the Service Center is the responsibility of
Wide screen format LED Displays (with 16:9 aspect
the purchaser. Conditions covered are limited
ratios, the ratio of the screen width to height) are
only to manufacturing defects in material or
primarily designed to view wide screen format
workmanship, and only those encountered in
full-motion video. The images displayed on them
normal use of the product.
should primarily be in the wide screen, 16:9 ratio
format, or expanded to fill the screen, if your model Excluded, but not limited to, are any originally
offers this feature, with the images constantly in specified provisions for, in-home or on-site
motion. Displaying stationary graphics and images services, minimum or maximum repair times,
on the screen, such as the dark sidebars on non- exchanges or replacements, accessories,
expanded standard format television video and options, upgrades, or consumables.
programming, should be limited to no more than For the location of a SAMSUNG Authorized
5% of the total television viewing time per week. Service Center, please call toll-free:
Additionally, viewing other stationary images and - In the United States: 1-800-SAMSUNG (1-
text such as stock market crawls, video game 800-726-7864)
displays, station logos, web sites or computer
graphics and patterns, should be limited as - In Canada: 1-800-SAMSUNG
described above for all televisions. Displaying
stationary images that exceed the above guidelines Still image warning
can cause uneven aging of LED Displays that
leave subtle, but permanent burned-in ghost Avoid displaying still images (such as jpeg picture
images in the LED picture. To avoid this, vary the files), still image elements (such as TV channel
programming and images, and primarily display logos, stock or news bars at the screen bottom
full screen moving images, not stationary patterns etc.), or programs in panorama or 4:3 image format
or dark bars. On LED models that offer picture on the screen. Constantly displaying still pictures
sizing features, use these controls to view different can cause image burn-in on the LED screen, which
formats as a full screen picture. will affect image quality. To reduce risk of this effect,
please follow the recommendations below:
Be careful about the television formats you select
and the length of time you view them. Uneven LED • Avoid displaying the same TV channel for long
aging as a result of format selection and use, as periods.
well as burned in images, are not covered by your
Samsung limited warranty. • Always try to display any image in full screen.
Use the TV set's picture format menu for the
• SAMSUNG ELECTRONICS NORTH best possible match.
AMERICAN LIMITED WARRANTY STATEMENT
• Reduce brightness and contrast to avoid the
Subject to the requirements, conditions,
appearance of after-images.
exclusions and limitations of the original Limited
Warranty supplied with Samsung Electronics • Use all TV features designed to reduce image
(SAMSUNG) products, and the requirements, retention and screen burn . Refer to the
conditions, exclusions and limitations contained e-Manual for details.
herein, SAMSUNG will additionally provide
Warranty Repair Service in the United States
on SAMSUNG products purchased in Canada,
and in Canada on SAMSUNG products
purchased in the United States, for the warranty
period originally specified , and to the Original
Purchaser only.

Downloaded from www.Manualslib.com manuals search engine

 SAMSUNG BRAND PRODUCTS
This limited warranty covers manufacturing defects in materials and
LIMITED WARRANTY TO ORIGINAL workmanship encountered 1n normal, and except to the extent otherwise
PURCHASER expressly provided for in this statement, noncommercial use of this
product, and shall not apply to the following, including, but not limited to:
This SAMSUNG brand product, as supplied and distributed by damage which occurs in shipment; delivery and installation; applications
SAMSUNG and delivered new, in the original carton to the original and uses for which this product was not intended; altered product or
consumer purchaser, is warranted by SAMSUNG aga1nst manufacturing serial numbers; cosmetic damage or exterior finishes; accidents, abuse,
defects in materials and workmanship for a limited warranty period of 90 neglect. fire, water, lightning or other acts of nature; use of products,
Days Parts and Labor for Commercial Use equipment, systems, utilities, services, parts, supplies, accessories,
applications. installations, repairs, external wiring or connectors not
Categories Parts Labor Size Service supplied or authorized by SAMSUNG which damage this product or
result in service problems; incorrect electrical line voltage, fluctuations and
40" Carry-In or In
and Larger surges; customer adjustments and failure to follow operating instructions,
Home
LCD/LED 1V 1 Year 1 Year cleaning, maintenance and environmental instructions that are covered
37" and prescribed in the instruction book; reception problems and distortion
Carry-In related to noise, echo, intelierence or other signal transmission and
and Smaller
delivery problems; brightness related to normal aging, or burned-
Carry-In or In in images. SAMSUNG does not warrant uninterrupted or error-free
Plasma Display 1 Year 1 Year All
Home operation of the product.
Projector THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE
Carry-In or LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER
(Excluding Lamp 2 Year 2Year All
Pick up EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
")
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
PICO&LED Carry-In or A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS
1 Year 1 Year All
Pocket Projector Pick up WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS
•• 180 Days after Purchasing and 600 Hours of Use Lamp on Projector WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR
CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE
This limited warranty begins on the original date of purchase, and is valid BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR
only on products purchased and used in the United States. To receive LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS
warranty service, the purchaser must contact SAMSUNG for problem OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
determination and service procedures. Warranty service can only be CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR
peliormed by a SAMSUNG authorized service center. The original dated INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL
bill of sale must be presented upon request as proof of purchase to THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG
SAMSUNG or SAMSUNG's authorized service center. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR
SHALL RECOVERY OF ANY KIND AGAINST SAM SUNG BE GREATER
SAMSUNG will repair or replace this product, at our option and at no
IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD
charge as stipulated herein, with new or reconditioned parts or products if
BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT
found to be defective during the limited warranty period specified above.
LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
All replaced parts and products become the property of SAMSUNG
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
and must be returned to SAMSUNG. Replacement parts and products
PURCHASER'S PROPERTY AND TO OTHERS AND THEIR PROPERTY
assume the remaining original warranty, or ninety (90) days, whichever is
ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS
longer.
PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE
Certain products are eligible for In-home service at Samsung's discretion. NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT
To receive in-home service, the product must be unobstructed and EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER
accessible to service personnel. If during in-home service, repair cannot OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
not be completed, it may be necessary to remove, repair and return EXCLUSIVE REMEDY.
the product. If in-home service is unavailable, SAMSUNG may elect,
Some states do not allow limitations on how long an implied warranty
at our option, to provide for transportation of our choice to and from a
lasts, or the exclusion or limitation of incidental or consequential
SAMSUNG authorized service center. Otherwise, and for 37" and smaller
damages, so the above limitations or exclusions may not apply to you.
LCD/LED 1V, transportation to and from the SAMSUNG authorized
This warranty gives you specific legal rights, and you may also have other
service center is the responsibility of the purchaser.
rights which vary from state to state.
To obtain warranty service, please contact SAM SUNG at:
Samsung Electronics America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660-2112
1·800-SAMSUNG (7267864) - www.samsung.com
1-800-749-0260: Projectors only

Downloaded from www.Manualslib.com manuals search engine

 Contact SAMSUNG WORLDWIDE
If you have any questions or comments about Your Samsung TV, please contact the SAMSUNG customer care center.

CANADA 1-800-SAMSUNG (726-7864) www.samsung.com Samsung Electronics Canada Inc., Customer Service 55
Standish Court Mississauga, OntariO L5R 482 Canada
U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com Samsung Electronics America, Inc. 85 Challenger Road
Ridgefield Park, NJ 07660

1111111111111111111111111111111111111111111
© 2013 Samsung Electronics Co. , Ltd. All rights reserved. BN68-04791 A-00
Downloaded from www.Manualslib.com manuals search engine
 Welcome to your new Smart TV!
QUICK START The fol lowing instructions cover assembling, connecting, and setting up your new TV. Make
sure you have the accessories listed below.

GUIDE Included in this box

11111111111111111111111111111111111111111 Remote Control Stand Parts and Cables

BN68-05028A-OO

Cable manager Stand Mount

Insert the Power on and

·~
Attach the TV to Connect video
batteries into the start the initial
the Stand devices
remote control setup

Remote Control lA extender Power cord

x2

Batteries (AAA x 2) Wal l mount adapter

Warning: Screens can be damaged (46 inch and above models)
from direct pressure when handled
incorrectly. We recommend lifting the
TV by the edges, as shown.

Step 1 Attach the TV to the Stand

1
Lay the TV on a soft surface, screen side down.
Use the packing material to protect the screen. 4 Insert 4 screws and secure the stand to the
mount.
p x4(M4XL12)

Holding the stand parallel to the screen, slide

5 the stand into the notches on the back of the

TV.
Put a base and screws off to assemble the

2
stand out of the box.

Screws
I/~ 32 inch models: 7 pieces
40 inch and above models: 8 pieces
Base Screws

Fit the stand and mount together, making sure Insert screws and secure the stand to the TV.

3 the notch on the mount aligns with the stand.

6 p x3 (M4 X Ll2) 32"

~ x4(M4XL12)39"-55"

Downloaded from www.Manualslib.com manuals search engine

 Step 2 Connect video devices
We suggest using HDMI connections whenever possible for the best picture quality.
The displayed image may differ depending on the model.

USB Connections Power Input

You can connect USB storage devices
to the USB jacks and enjoy personal
photos, videos, and music.

Wired Ethernet

Best Connection: HDMI HDMICable

We suggest using HDMI whenever

possible.

-
HDMI 1 is the default port for a HDMI Port You can connect home theater
cable or satellite set-top box. systems to the OPTICAL or AUDIO
OUT ports.
Use the other ports for Blu-ray
players, game consoles, and other
devices.

Good Connection: Component and AV

Match the colors on your device's cables to the colors
Connect the cable from the on the jacks. Connect the yellow composite video out
antenna or cable TV outlet. connector from an AV device to the green AV IN jack.

AV also accepts component video

connections (red/green/blue).

Connect theIR extender to theIR

Out port to control external devices
connected to the TV using the Smart
Touch Control. For more detailed
The AUDIO OUT port can connect
information, refer to the .. Universal
to a speaker.
Remote Control Setup" section on the
User manual.

Make sure you have the correct cable before plugging it in. Illustrations of common plugs and
Step 3 Insert the batteries into the remote control jacks are shown below.

Cable Plugs Ports I Jacks

' -
HDMI

0 USB

Step 4 Power on and start the initial setup

Information required :
Optical

' •
Troubleshooting
The stand is wobbly or crooked
Warning
Do not plug cables in upside down.
Be sure to check the orientation of
the plug before plugging it in.

Wi-Fi network password (if you use one) Make sure the arrows on the stand are properly aligned.
Zip code The TV won't turn on
Cable or satellite provider info
Make sure all cables are fully inserted, and that the remote has batteries installed.
The TV must be connected to the Internet to use the Smart Features. If you have a wireless
network, we recommend that you confirm that your network router is switched on and working My remote, gesture, or voice controls don't work
before you start the initialsetup.lfyou have a wired network, we recommend that you connect
The TV ships with protective stickers covering some of the sensors. Make sure all of them have
the TV to the network with a CAT 7 cable before you begin.
been removed.

I have extra parts

(!)Power on to start the initial setup.
The TV includes some optional parts to help with wall mounting and cable routing.

Connect to your network (wired or wireless) Search for channels from

your TV service provider If you experience issues, please do not take the TV back
to the store.
.L...::J
"'""J_)
~ In the United States of America, call us at
((C . . or 1-800-SAMSUNG (1-800-726-7864) or visit us at www.
samsung.com/spsn for support and warranty service.
For other countries, refer to "Contact SAMSUNG
After you have finished the initial setup, you can configure the universal remote control settings.
WORLDWIDE" in the user guide.
These settings let the Smart Touch remote control external devices connected to the TV, such as a
set-top box or Blu-ray player.

Congratulations on your new Smart TV!

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
 IMPORTANT SAFETY PRECAUTIONS

• Placing the television on a platform, stand, cabinet, table or other surface which is:
- recommended by Samsung or sold with the product;
- secure and stable;
- sufficiently wider in the base than the base measurement of the television;
strong and large enough to support the size and weight of the television.
• Positioning the television close to the wall to avoid the possibility of the television falling when pushed.
• Ensuring your television is installed by an authorized Samsung installer.
• Following the instructions for wall mounting in the installation manual and using the mounting equipment supplied by Samsung.
• Placing the television toward the back of the furniture or surface on which it is placed.
• Ensuring that the television does not hang over the edge of the furniture or surface on which it is placed.
• Not hanging anything from or on the television.
• Anchoring both the television and the furniture on which it is placed to a suitable support especially in the case of tall furniture, such as
• cupboards or bookcases which exceed one metre in height. This can be done by using sturdy brackets, safety straps or mounts that
are made specifically for flat screen televisions.
• Not placing any material between the television and the furniture on which it is placed.
• If the furniture on which the television is placed has drawers, cabinets or shelves under the television, taking steps to prevent children
from climbing, such as installing safety latches so the doors cannot be opened.
• Keeping pets away from the television
• Educating children about the dangers of climbing on furniture to reach the television or its control.

Failure to take these safety precautions may cause the television to fall from the stand or mounting equipment,
causing damage or serious injury.

Downloaded from www.Manualslib.com manuals search engine

 Regulatory Compliance Statements

- Federal Communications Commission (FCC) - USA

- Industry Canada Equipment Standard for Digital Equipment (ICES-003) - Canada
- Voluntary Control Council for Interference (VCCI) - Japan
- Bureau of Standards Metrology and Inspection (BSMI) - Taiwan
- Korea Communications Commission(KCC) - Republic of Korea
- Italian Post Ministry (Homologation) - Italy

FCC Class A Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

1B This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Class B Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
(B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance w ith the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation . If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a c ircuit different from that to which the receiver is connected .
- Consult the dealer or an experienced radiofTV technician for help.

User Information
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment. If necessary, consult with your dealer or an experienced radio/television technician for additiona suggestions. You may find the
booklet called How to Identify and Resolve RadiofTV Interference Problems helpful. This booklet was prepared by the Federal Communications
Commission. It is available from the U.S. Government Printing Office. Washington, DC 20402, Stock Number 004-000-00345-4.

The party responsible for product compliance:

SAMSUNG ELECTRONICS CO., LTD.
America OA Lab of Samsung
335 1 Michelson Drive
Suite #290, Irvine, CA92612 USA

Warning
User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this monitor is a detachable
power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar
configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor
and that the ampere rating of the computer convenience outlet is equal or exceeds the monitor voltage rating. For 120 Vo lt applications,
use only UL Listed detachable power cord with NEMA configuration 5- 15P type(parallel blades) plug cap. For 240 Volt applications use
only UL Listed detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. This television receiver
provides display of television closed captioning in accordance with Section 15. 11 9 of the FCC rules. (TV broadcast receivers with picture
screens 13 inches or larger in diameter models only)

Downloaded from www.Manualslib.com manuals search engine

 ICES-003 Class A Notice -Avis NMB-003, Classe A
This Class A digital apparatus complies with Canadian ICES-003.
a
Cet appareil numerique de Ia classe A est conforme Ia norme NMB-003 du Canada.

ICES-003 Class B Notice -Avis NMB-003, Classe B

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de Ia classe B est conforme a Ia norme NMB-003 du Canada.

VCCI Class A Notice

;:: O)~@:IJ:, ? 7 "A A tUIHtf.f.j~@:"""C9 o
;::O)~@:~%a!!~~-cfj!J!'l9 ~ c ~;.11i~Ji~~:SI ~~;:: 9;:: c fJ{~ ~J *9 o

;::O)~~I=IJ:'If:Jfl~fJ{jlt;J]to:~* ~~9 ~ J:? ~* ~n~;:: c fJ{~ ~J *9 o

VCCI Class B Notice

;::O)~@:IJ:, ?7"AB tUIHt1t.T~@:-c9 o
;:: O)~ @: IJ:, %a!~~-c'lf:m9 ~;:: c ~ El!Y-J c l -n '*9fJ{, ;:: O)~ ji: fJ{7 ~;tf.:>-T v t::' ~ =t ::..--~f~Wt=iliH~ vc 'lf:!fl ~
n~ c, ~f~~t§:~sl ~~;:: 9;:: c JJ{~ ~J *9 o
.!fl1f&IDti3Jl:J:I=~-?""CiE 1..-L'.!f)( ~H&L'~ l""Cl'~L' o

CCC Class A notice - China

~~AgF~ . ~~m~~~. ~F~~-~~~~~*~tt .
~~Mm~l'. ~••~m~~x~m*um~~fi~m• .

BSMI Class A Notice

The following statement is applicable to products shipped to Ta1wan and marked as Class A on the product
compliance label.

~{!j{!J!ffj~ :
s~~••m•~ ~·~~tt~m~~m~·~~-~~M~~~· rr~•m~~
~m ~•~~ *~~~~-~~Mm ·

CE
BSMI Class A Notice
Products with the CE marking comply with the EMC Directive(2004/ 108/ EC) and the Low Voltage
Directive(2006/95/ EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:

- EN55022 : Radio Frequency Interference

- EN55024: Electromagnetic Immunity of Information Technology Equipment
- EN61000-3-2: Power Line Harmonics
- EN61 000-3-3: Voltage Fluctuations
- EN55013: Radio disturbance characteristics of broadcast receivers and associated equipments
- EN55020: Electromagnetic immunity of broadcast receivers and associated equipm

European Class A Warning

(If the user manual declares the product as Class A, following statement applies.)
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

AEf 7/7/ (gj.!f!.i§ 16'"15~t.J7/XfXH)

Of 7 (7 ( ~ ~.!:j!§(A~) ~:A~nf~g,t"7(7(£.A.i Jt.fD H :A~ Ef.~ J..~§:A~ ~ Of~ ~ 4-Qj o~.A.f 7 f t:l~2.~0:j , 7 ~ ~2.f Qf :A fQ:10lfAi
;.. ~§-o~ ~ 3.:!~ ~~0£ g,t-Lfq.
BEl 7/7/ (7f~i§ 16'"-&~t.J7/XfXH)
Of 7 f7 f::: 7 ~~ -§(B~) ~:Afnf~g,t"7f7f£J..i 4-£ 7~~0if .A.i J..f-§"0~~ 3.:! ~ ~~ 0 £ -o~O:j . 2 ::=:: :AfQ:10ifJ..i ;..~-§ ~ 4
~~Lfq.

Italian Homologation Notice

Ouesto apparecchio e fabbricato in conformita al D.M.28.08.95 n.548
ed in particolare a quanto specificate nell Art.2, comma 1.
Questo apparecchio e fabbricato nella U. E. in conformita al D. M.28.08.95 n.548
Art. 2, comma 1 ed al D.M.26.03.92 Art.1
- For products produced in countries except European Community
Questo apparecchio e fabbricato in conformita al D.M.28.08.95 n.548
ed in particolare a quanto specificate nell Art.2, comma 1.
- For products produced in European Community
Ouesto apparecchio e fabbricato nella U.E. in conformita al D.M.28 .08.95 n.548
Art.2, comma 1 ed al D.M. 26.03 .92 Art.1
Downloaded from www.Manualslib.com manuals search engine
 Important Safety Instructions {UL Only)
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer's Instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit
from the apparatus.
11 . Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.

• Ventilation
Do not place the apparatus in a rack or bookcase. Ensure that there is adequate ventilation and that you've followed that manufacturer's
instructions for mounting and installation.

MPR II Compliance (MPR II applied model only)

This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.

Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA only)
Contains Mercury, Dispose According to Local, State or Federal Laws

Downloaded from www.Manualslib.com manuals search engine

 Wiring the Mains Power Supply Plug(UK Only)

IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face
of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same
colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should
obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative but to cut off the
plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.

IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows :
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter Lor coloured BROWN or RED.

WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.

Russia Only - PCT Notice

~~
AB57

MPR II Compliance (MPR II applied model only)

This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.

Downloaded from www.Manualslib.com manuals search engine

 EU Eco-Label (EU Eco-Label applied model only)

Products which have model codes that end in XU are intended for the UK market. Samsung has not applied for Ecolabels for products with this
specific model code.

***
** f ** Better for the environment. ..
• High Energy Efficiency
* *
Eu)i~
• Reduced C02 emissions
• Designed to facilitate repair and recycling

... better for you.

Ecolabel
www.ecolabel.eu

[.___E_u_E_c_o_la_b_e_l:_H_u_J_o_22_J_o2_ __..]
SAMSUNG Electronics makes an effort to develop environment-friendly product that minimizing an impact to environment through whole
process from getting raw materials, production, transportation, usage and end-of-life disposal by adding 'environment' on function, price,
quality, design that were the essence for product development.
These environmental characteristics are endorsed by the award of the European Eco-label (also known as the Euro Flower) issued by
the European Commission as approval of the product environmental status for energy saving, facilities for recycling and a host of other
features. The full list of criteria and more information on the ecolabel canbe found at t he web-site address: http://www.ecolabel.eu

Recycling Information (Take-back offer)

For recycling information for our products, please contact the company corresponding to your region of residence.
For those who reside in other countries, please contact a nearest local Samsung dealer for recycling information for the products to be treated
in environmentally acceptable way.
The information of Regional Takeback Schemes can be found at Samsung's web-site.
http://www.samsung.com/recycling_compliance

CIS Only

Clt1MBOn «He An5l nifl~eBOH npOAYKI..liflifl» nplt1M8HHeTCH B COOTBeTCTBifle CTeXH!f1YeCK!f1M pernaMeHTOM

® TaMo>KeHHoro cotoJa «0 6eJonacHOCTif1 ynaKOBKifl» 005/2011 1t1 yKaJbiBaeT Ha TO, YTO ynaKOBKa AaHHoro
npOAYKTa He npeAH33HaYeHa AnH noeTopHoro ifiCnonbJOBaHifiH 1t1 noAne>KifiT YTiflnifiJal.liflifl . YnaKOBKY
AaHHoro npOAYKTa Janpe~aeTcH iflcnonbJosaTb AnH xpaHeHifiH nifl~esoH npOAYKI..liflifl.

en CliiMBon «neTnH Me6111yca» yKaJbiBaeT Ha B03MO>KHOCTb ynmlt133l.lifllil ynaKOBKI!I. CI!IMBOn MO>KeT

6b1Tb AOnOnHeH 0603H3Y8Hif18M M3T8plilana ynaKOBKifl B BI!IA8 l..\lilcppoeoro 1!1/liln lil 6yKB8HHOro
0603H3Y8Hiil5l .

®
CliiMBon KeAeHAiK OA31\fblli 005/2011 T8XH!f1Kanbl~ pernaMeHTiHe caiiiKec ~OnAaHbln3Abl >KaHe OCbl
eHiMHili ~anraMaCbiH eKiHwi peT naiiiAanaHyra apHanMaraHbiH >KaHe >Kotora >KaTaTbiHbiH KepceTeAi.
0Cbl eHiMHili ~anTaMaCbiH 33bl~-ryniK 8HiMA8piH C31\f3Y ywiH naiiiAanaHyfa TbliilbiM canbiH3Abl.

a CliiMBon ~amaMaHbl >KOto MVMKiHAiriH KepcereAi. CI!IMBOn caHAbl~ KOA >KaHe/HeMece apin
6enrinepi TypiHAeri ~anraMa MaTepl!lanbiHblli 6enriciMeH TOnbll\fblpblnYbl MVMKiH.

1111111111111111111111111111111111111111111
Downloaded from www.Manualslib.com manuals search engine BN68-04972A-01
 Screws and Guide stand location
~

::J
0
>.Q)
..cc
:t:::O
:;::..c
c.. (Except LED ES 8000 and higher)
.!!? t:::
..CC"C
-E
~Ul
(.)
U) Product Size Location

t:
0 0
a,) Cl.
·->
"CC
t
Cl.
= LED TV 26"-46"

-::sen
'I-C..
c
0
c..
c..
::::l
en
Cl)
l:noo::;t
Co
--
Screws/
Cl.~ ......._
:::StO Guide-Stand
-Q,)o
E E en~"-
.Cu
0
Em
.. --- --- ---
(..)
cam
.c
u
ca
a,) E
C')
c
::::l
en ....c
ca E
C')
c
::::l
en
en'?
00
-00
-oo
ca,
Plasma
43"-51"
Cl)
~
en c.,) ~
en (.).,..... TV
---
Screws(
Guide-Stand
w
a:
0
l- ~- --- --- ---
en
LED 55"
0 LED TV
1- Plasma TV
Plasma 59" .........
z And larger
a: Screws/
Guide-Stand
::J
1-
w
a: English
Screws and guide stand package is placed in the Styrofoam on top.
1-
0 Espaiiol
z Los tornillos y Guide Stand se encuentran localizados en el Styrofoam superior.
0
0 Fran~ais
Les vis et le paquet du guide du support sont places dans Ia mousse de
polystyrene sur le dessus.

Downloaded from www.Manualslib.com manuals search engine

 Top 6 Troubleshooting Tips TV 6 Problemas Principales :d TV Handling Guide
1 . Can't Connect with Network or Apps (For internet supported model only) 1. No se puede conectar con Ia Red o Apps (Solo para model as que
• Make sure there is a network connection soporten conexi6n a internet)
(Menu ~ Network ~ Network status) • Asegurese que el equipo este conectado a una red
• Contact your service provider (Menu ~ Red ~ Estado de Red)
• Contactar a su proveedor de Internet
2. No Picture/Sound or Distorted Picture/Sound with an External Device
2. No hay lmagen/sonido o Distorsi6n de Imagen/sonida con un
• Make sure your connection to the device is correct. dispositive externo
• Perform a TV Self Diagnosis to identify the problem • Asegure que Ia conexion fisica del dispositive sea correcta
(Menu ~ Support ~ Self Diagnosis ~ Sound or Picture Test) • Para identificar el problema, realice un Auto d iagnostico en Ia TV ·I ish
• Change the picture size (Use "P. Size" button on your remote) (Menl.J ~ So porte de Tecnico ~ Au!odiagnostico --?l'rullba de Imagen o Sonido)
1 you lift up a 55" or larger TV, your thumd touches the sareen directly, you
• Cambie el tamano de Ia irnagen (Use el boton "P. Size" del control remota)
1m age the screen . Samsung recommends you lift up the TV as shown in PIC.
3. Poor Picture Quality
• Verify your signal is High Definition o r Standard Definition 3. Mala Calidad de Imagen I
(Contact your service provider) • Verificar si su senal es Alta Definicion o Definicion Regular ;e levante una TV de 55" o mayor, si el dedo pulgar toea Ia pantalla
(Contactar a su proveedor de Serviciqs)
nte, puede dar'iar Ia pantalla. Samsung recomienda que levante Ia TV
4. Your Settings are Lost after 30 Minutes 1uestra en Ia FIG.
4. Su configuraci6n se pierde despues d e 30 minutos
• Change to Home Mode • Cambiar a Uso Domiciliario
("Tools" on your remote ~ Store Demo Off) (Use el boton "Tools" del control rernoto ~ Demo Cornercio Desac.) ous soulevez un televiseur 55" ou plus, si votre pouce touche directement
5. "Weak or No Signal" Displayed in TV Mode/Cannot Find Channel .. dn, vous pouvez en dommager l'e cran. Samsung recommande vous soulevez
5. " Senates Debiles o lnexistentes" Mensaje desplegado en
• Press Source button on your remote TV Mode I No puede encontrar canales te televiseur, comme indique dans Ia photo.
• Run Auto Program and search for channels • Presione el bot6 n "Source" en su control remota r-;;,
(Menu ~ System ~ Plug & Play ~ Enter) • Corra Auto Program e inicie busqueda de canales
(Menu ~ Sistema ~ Plug & Play ~ Enter)
R Screen Care Guide
6. Can't See All Apps or Apps Not Working
6. No se ven todas las Aplicaciones o no funcionan
Reset Sm art Hub
Resetear Smart Hub
(Too ls in main page of Smart Hub ~ Settings ~ Reset (Herramtentas en Ia pagina princtpal de Smart Hub ~ Conftguracion ~ Reset
Enter with Password, Default Password is 0000) lntroducir Ia Contrasena, Ia Contrasena Predeterminada es 0000)

II.• - .• II II II. Btl•

English
Scan the QR code to view
our helpful How-to Videos
~ ·. . Do not spray cleaning solutopn directly onto the TV screen. Spray the solution onto
a cleaning cloth first, and then clean the screen .
t ',:: ;>f ::;Cll o) i ( (.•dt<;<.~ ';.f( Pn ,', ';V' · ;Lr· :.t ~ (:.' >~!tit·<_:'
~·- ~ i!J ..:.•. 8 ~
~- . Espaiiol
·. i•:•n;.• ' ' " 1~-.:,•-: <!,,, \'•:.i ~ ~
• , . jl •

0 No rocie Ia soluci6n de limpieza directamente sobre Ia pantalla del televisor .

Rocie Ia soluci6n sobre un par'io de limpieza, y luego limpie Ia pantalla.
Franc;ais
Ne pas pulveriser Ia solution de netto yage direnctement sur l'e cran du televiseur.
Pulveriser Ia solution sur un chiffon de netto yaged' abord , puis nettoyer l'e cran.

Downloaded from www.Manualslib.com manuals search engine