BACHELOR OF ENGINEERING (ELECTRICAL & ELECTRONICS)

V SEMESTER

Ref No. Subject SCHEDULE OF SCHEME OF EXAMINATION

TEACHING THEORY PRACTICAL
L T P Total Pape Hrs. Sess. Total Sess. Viva Total
r -voce
EE-511 Power Systems-II 3 1 - 4 100 3 50 150 - - -
EE-561 Power Systems-II - - 3 3 - - - - 50 25 75
Lab
EE-512 Electric Machinery- 3 1 - 4 100 3 50 150 - - -
II
EE-562 Electric Machinery- - - 3 3 - - - - 50 25 75
II Lab
EE-513 Microprocessors and 3 1 - 4 100 3 50 150 - - -
Interfacing
EE-563 Microprocessors and - - 3 3 - - - - 50 25 75
Interfacing Lab
EE-514 Instrumentation 3 1 - 4 100 3 50 150 - - -
Systems
EE-564 Instrumentation - - 3 3 - - - - 50 25 75
Systems Lab
CSE-511 Computer Networks 3 1 - 4 100 3 50 150 - -
EE-560 Seminar - - 3 3 - - - - 100 - 100
EE-564 Vocational Training - - - - - - - - 100 - 100
of Fourth Semester
Total 1 5 1 35 500 - 250 750 400 100 500
5 5
 EE- 511
Power Systems-II
LTP
310
External: 100
Sessional: 50

Note: Examiner shall set eight questions, four from Part-A and four from Part-B of the
syllabus. Candidate will be required to attempt any five questions selecting at least two
questions from Part A and two from Part B.

Part-A
1 Power System Protection
System Protection Components, Instrument Transformers, Overcurrent Relays, Radial
System Protection, Reclosers and Fuses, Directional Relays, Protection of Two-
Source System with Directional Relays, Zones of Protection, Line Protection with
Impedance (Distance) Relays, Differential Relays, Bus Protection with Differential
Relays, Transformer Protection with Differential Relays, Pilot Relaying, Digital
Relaying
Power System Overvoltages, protection against over voltages by shielding or ground
wires and lightning arrestors, insulation coordination.
13h
2. Circuit Breakers
Transient recovery voltage, resistance switching, first pole to clear factor, Transient
recovery voltage, arc and arc extinction, volt ampere characteristics of arc, methods
of arc extinction, construction, working and applications of air-break circuit breakers,
oil circuit breakers, vacuum circuit breakers, air blast circuit breakers, SF6 circuit
breakers, circuit breaker ratings 10 h
3. Substations and Distribution
Location and types of substations, bus-bar arrangements, major substation equipment
Types of insulators, voltage distribution across suspension insulators, string
efficiency, methods of improving string efficiency
Types of Underground cables, capacitance of single core cables, grading of cables,
capacitance of three core belted cables, power factor and heating of cables
Radial, parallel or loop, network or grid types of distribution systems and their
relative merit. 10 h
4. Grounding
Grounding fundamentals, Ground resistance, step voltage, touch voltage and
transferred voltage, tolerable step and touch voltages, ground resistance of a
 hemisphere and driven rod, IEEE Standard 80 formulae for ground resistance and
step and mesh voltages of a grounding grids, limitations of the formulae
Neutral grounding: ungrounded systems, resonant grounding, solid or effective
grounding, reactance grounding, earthing transformer, neutral grounding practice
8h

Text Book / Standards

1. J. D. Glover, M. S. Sarma, ‘Power System Analysis and Design’, Thomson-
Brooks/Cole, 2002
2. I. J. Nagrath, D. P. Kothari, Power System Engineering, TMH, 1994
3. IEEE Guide for Safety in AC Substation Grounding, ANSI/IEEE Std. 80-2000,
2000
Other Recommended Books
1. S.N. Singh, ‘Electric Power Generation, Transmission and
Distribution’, PHI, 2003.
2. Weedy & Cory, Electric Power Systems, John Wiley &
Sons, 1999
3. IS:3043 -1987, Indian Standard Code of Practice for
Earthing, BIS, New Delhi, 1987
4. Y. G. Paithankar and S. R. Bhide, Fundamentals of Power System Protection,
PHI, 2003
 EE- 561
POWER SYSTEMS II LAB

Note: At least eight experiments / projects / technical reports relating to the

following:
1. Measurement of soil resistivity and soil model evaluation
2. Measurement of ground resistance.
3. Grounding system design for a substation.
4. To study the characteristics of over current relay.
5. To study the characteristics of percentage differential relay.
6. To study the characteristics of distance relay.
7. To study current time characteristics of fuses.
8. Technical visit to a substation/generating station, Load Dispatch Centre and
preparation of a technical report for the same
9. Conventional and renewable energy sources
10. Distribution system design
11. Digital relaying
12. Reactive compensation of lines
 EE- 512
ELECTRICAL MACHINERY-II

LTP
310
External: 100
Sessional: 50

Note: Examiner shall set eight questions, four from Part-A and four from Part-B of the
syllabus. Candidate will be required to attempt any five questions selecting at least two
questions from Part A and two from Part B.

Part-A
Synchronous Machines: (18)

Introduction, basic synchronous Machine Model (Realistic Machine), Voltage

regulation, Circuit model of synchronous machine, determination of synchronous
reactance, Open circuit characteristic(OCC), short circuit characteristic (SCC), Short
circuit ratio (SCR), short circuit loss, Determination of armature Reaction, ampere-turns
and Leakage reactance of a synchronous machines-Potier method, Nature of armature
reaction, salient pole synchronous machine-two reaction model, analysis of phasor
diagram, power angle characteristic, determination of Xd and Xq using slip test, V-curve,
Inverted V-curve of synchronous machine, hunting in synchronous machines, damper
winding, short circuit transients in synchronous machine, short circuit under loading
conditions, single phase synchronous generators, synchronous condenser.
Part-B

Parallel operation of alternators: (12)

Synchronizing to infinite Bus-Bars, synchronoscope, parallel operation of alternators,

Operating characteristics, generating Machine, motoring machine, power angle
characteristic, operation at constant load with variable excitation, generating Machine,
motoring machines, minimum excitation, observation, compounding curve, synchronous
condenser, consideration of armature resistance, power flow (transfer) equations,
Special motors: (10)

Brushless dc motors, schematic and operation, circuit model characteristics of brushless

dc motor, PM Brushless dc machine, universal motor and stepper motor, linear induction
motor, Hysteresis motor, reluctance motors
Text Books:
1 I.J Nagrath, D.P. Kothari, Electrical Machines, TMH Publishing Company, 2002.
2. P.S. Bhimbhra, Electrical Machinery, Khanna Publishers, 2003.
Other Recommended Books:
1 Electrical Machinery and Transformers by Bhag S. Guru and Huseyin R. Hiziroglu,
2.New York Oxford University Press 2004 Electrical Machines by Smarjit Ghosh,
Pearson Education Singapore PTE. Ltd. 2005.
3. Electric Machinery by A.E. Fitzgerald, Kingsley, Umans, TMH Publishing Company,
2002
 EE- 562
ELECTRICAL MACHINERY-II LAB
LTP
003
External: 25
Sessional: 50

Note: At least eight experiments are to be performed.

1. To perform no load test on a 3 phase alternator (cylindrical rotor).

2. To perform short circuit test on a 3 phase alternator (cylindrical rotor). Measure
the resistance of stator winding of alternator. Find out regulation of alternator at
full load at (i) unity power factor (ii) 0.85 Power factor lagging (iii) 0.85 Power
factor leading using synchronous impedance method.
3. To synchronize an alternator with the 3 phase supply.
4. To perform the parallel operation of two alternators.
5. To perform the slip test to determine the Xd and Xq.
6. To run a stepper motor in different modes with the help of microprocessor.
7. To analyze the power factor improvement of an industry and design the capacitor
bank.
8. Computer aided transformer design
9. Computer aided induction machine design
10. Computer aided synchronous machine design
11. To obtain positive, negative and zero sequence impedances of a three phase
synchronous generator
12. To obtain positive, negative and zero sequence impedances of a three phase
transformer
 EE- 513
Microprocessors and Interfacing

LTP
310
External: 100
Sessional: 50
Note: Examiner shall set eight questions, four from Part-A and four from Part-B of the
syllabus. Candidate will be required to attempt any five questions selecting at least two
questions from Part A and two from Part B.

Part-A

Microprocessor Architecture and Microcomputer Systems; Microprocessor

Architecture Memory, Input and Output Devices, The 8085 MPU, Example of an 8085-
Based Microcomputer, Memory Interfacing. (4 h)

Interfacing I/O Devices: Basic Interfacing Concepts, Interfacing Output Displays,

Interfacing Input Devices, Memory- Mapped I/O, Testing and Troubleshooting, I/O
Interfacing Circuits. (4 h)
Programming the 8085: Introduction to 8085 Assembly Language Programming, The
8085 Programming Model, Instruction Classification, Instruction Format. Data Transfer
(Copy) Operations, Arithmetic Operations, Logic Operations, Branch Operations,
Writing Assembly Language Programs. (5 h)
Programming Techniques: Looping, Counting and Indexing, Additional Data Transfer
and 16-Bit Arithmetic Instructions, Arithmetic Operations Related to Memory, Logic
Operations. (4 h)
Part-B

Counters and Time Delays: Counters and Time Delays, Hexadecimal Counter, Modulo
Ten, Counter, Generating Pulse Waveforms, Debugging Counter and Time-Delay
Programs. (4 h)
Stack and Subroutines: Stack, Subroutine, Conditional Call and Return Instructions.
(2 h)
Interrupts : The 8085 Interrupt, 8085 Vectored interrupts. (2 h)

Interfacing Data Converters: Digital- to- Analog (D/A) Converters, Analog- to- Digital
(A/D) Converters, stepper motor interfacing (4 h)
General –Purpose Programmable Peripheral Devices: The 8255A Programmable
Peripheral Interface, Illustration: Interfacing Keyboard and Seven- Segment Display,
Illustration : Bi- directional Data Transfer between Two Microcomputers, The 8254
Programmable Interval Timer, The 8259 A Programmable Interrupt Controller, Direct
Memory Access (DMA) and the 8257 DMA Controller, serial communication,
Programmable communications interface 8251,RS 232C. (6 h)
TEXT BOOK

Ramesh S.Gaonkar, “Microprocessor Architecture, Programming and

Applications with the 8085”

OTHER RECOMMENDED BOOKS:

Badri Ram, “Advanced Microprocessors & Interfacing”, Tata MC Graw Hill.

Charles M.Gilmore, “Microprocessor Principles and Applications”, TMH.
Douglas V. Hall, “Microprocessors and Interfacing programming and Hardware” TMH.
 EE-563
MICROPROCESSORS AND INTERFACING LAB
LTP
003
External: 50
Sessional: 25
Note: Attempt any ten programs..

1. Study of 8085 Microprocessor kit

2. Write Assembly Language Program to add n given numbers with and without
carry.
3. Write Assembly Language Program to count positive & negative numbers in
given n numbers.
4. Write Assembly Language Program to de-assemble 8- bit number in two nibbles.
5. Write Assembly Language Program to reassemble two nibbles in 8- bit number.
6. Write Assembly Language Program to sort given n numbers in ascending &
descending order using subroutine.
7. Write Assembly Language Program to relocate the given numbers in same &
reverse order.
8. Write Assembly Language Program to Flash different letters using your own
delay subroutine.

Inter facing of Microprocessor 8085:

1. To obtain a square wave on CRO

1. To interface A to D converter
2. To interface D to A converter
3. To interface input/output module for complementing the input data.
4. To interface stepper motor with µp to control its step size and direction of rotation
5. To develop a traffic light controller program and interface using Input/Output
Module.

.
 EE- 514
Instrumentation systems
LTP
310
External: 100
Sessional: 50
Note: Examiner shall set eight questions, four from Part-A and four from Part-B of the
syllabus. Candidate will be required to attempt any five questions selecting at least two
questions from Part A and two from Part B.
PART-A
1) Transducers & Standards
Standards of Instrumentation Systems and Their Classification: Emf, Current, Resistance
and Capacitance Standards. Sensors and Transducers: Primary Sensing Elements;
Characteristics; Classification.
Passive-Transducers-Resistive, Inductive, Capacitive; Types, Features, Configurations,
Analysis, Applications.
Active Transducers- Thermoelectric, Electromagnetic, Piezo-Electric, Photoelectric;
Types-Principle, Construction, Analysis and Applications.

2) Digital - Analog Instruments and Recording Systems

Data Telemetry: Digital Instruments - Block Diagram Of Digital Multimeters, Storage

Oscilloscope - Magnetic Tape Recorders - Direct Recording, Frequency Modulation
Recording, Digital Recording Technique - Floppy Discs -Digital Input - Output Devices.
PART-B
3) Signal Conditioning:
Analog Conditioning- Instrumentation and Logarithmic Amplifiers.
Digital Conditioning-A/D, D/A Converters-Common Types, Operation.
Types-Analog/Digital, Block Diagram, Operation, Comparative Performance
(Data Display and Recording Devices: Principle, Operation and Use of -LEDs, LCDs,
Recorders-Paper Chart, Magnetic Tape, Semi-Conductor;
4) Virtual Instrumentation
Introduction to lab VIEW Front Panel, Block Diagram, Tools And Palettes, Menus,
Code Debugging, Creating Sub-Vis, For Loop, While Loop, Structures, Arrays And
Clusters, Graphs And Charts, File Input And Output , Data acquisition and applications.
TEXT-BOOK

1. W.D. Cooper and A.D. Hilfrick: Electronic Instrumentation &

Measurement Techniques, PHI.
2 .A.K Sahnwey “Electronic and Electrical Instrumentation”.
3. R.H.Bishop, Learning with LabVIEW 7 Express,Pearson Education, Delhi.
References:

1. Murthy, D.V.S. - Transducers Instrumentation

2. Doeblin, E.O.-Measurement Systems (MGH)
 EE- 564
Instrumentation systems Lab
LTP
003
External: 25
Sessional: 50

Note : At least eight experiments are to be performed.

1) Displacement measurement using LVDT

2) To study the operation of Instrumentation Amplifier.
3) Measurement of flow using electromagnetic and positive displacement
parameters.
4) Measurement of level using capacitance probe differential pressure transducer.
5) Design of linearization circuit for thermistor.
6) Experiments based on Lab VIEW.
 CSE511
COMPUTER NETWORKS
LTP
310
External: 100
Sessional: 50

Note: Examiner shall set eight questions, four from Part-A and four from Part-B of the
syllabus. Candidate will be required to attempt any five questions selecting at least two
questions from Part A and two from Part B.
.
Part-A
Introduction (6)
Data Transmission concepts; switching; Modulation; multiplexing; Network Hardware:
LAN, MAN, WAN, Wireless Networks, Internet works; Network Software: Layer,
Protocols, interfaces and services; Reference Model: OSI, TCP/IP and their comparison.
Physical Layer (10)
Transmission media: Magnetic, Twisted pair, coaxial cable, fibre optics, wireless
transmission. Circuit Switching & Packet Switching. Introduction to Cellular radio and
communication satellite.
Data Link Layer (10)
Framing; Error control; Error Correction & Error Detection; Sliding window protocols;
Examples of DLL Protocols – HDLC,SLIP, PPP ; Medium Access Sub Layer: Channel
Allocation, MAC protocols – ALOHA,CSMA protocols, Collision free protocols,
Limited Contention Protocols , Wireless Protocols , IEEE 802.3,802.4,802.5 standards
and their comparison. Bridges: Transparent, source routing, remote.
Part-B

Network Layer (8)

Design issues, routing algorithms (shortest path, flooding, flow based, distance vector,
hierarchical, broadcast, multicast, for mobile host). Introduction to Congestion control
algorithms.
Transport Layer (5)
Addressing, establishing and releasing connection, flow control & buffering,
multiplexing, crash recovery, Internet Transport protocol (TCP and UDP).
Application Layer (6)
Basics of Network security, Domain Name System, Introduction of Simple Network
Management Protocol, Electronic mail and FTP.

Text Books
1. Computer Networks Andrew S. TanenBaum (PHI)
2. Data Communications and Networking, 3/e Behrouz A Forouzan (Mcgraw-
hill)
Other Recommended Books
1. Data and Communication William Stallings (PHI)
2. Data & Computer Communication Douglos E. Coomer (Addison Wessl