Model Name: T420HW09 V1: Issue Date: 2011/1/11 Preliminary Specifications (!) Final Specifications
Model Name: T420HW09 V1: Issue Date: 2011/1/11 Preliminary Specifications (!) Final Specifications
Model Name: T420HW09 V1: Issue Date: 2011/1/11 Preliminary Specifications (!) Final Specifications
Rev.0 2
( )Preliminary Specifications
(!
!)Final Specifications
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
7 INTERNATIONAL STANDARD
7-1 SAFETY
7-2 EMC
8 PACKING
9 PRECAUTION
9-5 STORAGE
Record of Revision
Version Date Page Description
0.0 2010/11/26 First release
0.1 2010/11/30 4 D: front bezel to inverter cover
22 Update Dmax value
23,24 Update 2D drawing
0.2 2011/1/11 16 Update input current max =5.26Adc, Inrush current max =7.5Adc
1. General Description
This specification applies to the 42.0 inch Color TFT-LCD Module T420HW09 V1. This LCD module has a TFT
active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 42.0 inch. This module supports
1,920x1,080 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical
stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
The T420HW09 V1 has been designed to apply the 8-bit 2 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.
* General Information
3. Electrical Specification
The T420HW09 V1 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The other is to power Back Light Unit.
3.1.1: DC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage VDD 10.8 12 13.2 VDC
Power Supply Input Current IDD -- 1 1.5 A 1
Power Consumption PC -- 12 18 Watt 1
Inrush Current IRUSH -- -- 3 A 2
LVDS Differential Input High Threshold Voltage VTH +100 -- +300 mVDC 3
Interface
Differential Input Low Threshold Voltage VTL -300 -- -100 mVDC 3
3.1.2: AC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
Note :
1. VDD = 12.0V, Fv = 60Hz, Fclk= 74.25MHz , 25 , Test Pattern : White Pattern
2. Measurement condition : Rising time = 400us
VDD
90%
10%
GND
400 µs
3. VICM = 1.25V
LVDS -
V IC M V TH
|V ID |
V TL
LVDS +
GND
|V ID |
0V
|V ID |
4. The measure points of VIH and VIL are in LCM side after connecting the System Board and LCM.
Note: x = 0, 1, 2, 3, 4
6. LVDS Receiver Clock SSCG (Spread spectrum clock generator) is defined as below figures
1/FSS
Fclk_
Fclk_ss(
ss(max)
max)
Fclk
Fclk_
Fclk_ss(
ss(min)
min)
tRIP2
tRIP3
tRIP4
tRIP5
tRIP6
tRIP0
tRIP1
LVDS-Rx
Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 Rx6
Input Data
LVDS-Rx
Input Clock Vdiff = 0V
1/Fclk=T
8. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape,
TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current
occurs between lamp wire and conducting tape.
9. The relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. At
temperatures greater than 40 , the wet bulb temperature must not exceed 39 . When operate at low
temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced.
10. Specified values are for a single lamp only which is aligned horizontally. The lifetime is defined as the time
which luminance of the lamp is 50% compared to its original value.
[Operating condition: Continuous operating at Ta = 25±2 ]
NS
LVDS Option = High/Open
C lo ck
C H x_0+ R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
C H x_0-
C H x_1+ G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
C H x_1-
C H x_2+
C H x_2- B3 B2 DE NA NA B5 B4 B3 B2 DE
C H x_3+
C H x_3- R7 R6 NA B7 B6 G7 G6 R7 R6 NA
Note: x = 1, 2, 3, 4…
JEIDA
LVDS Option = Low
C lo ck
CH x_0+ R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
CH x_0-
CH x_1+ G4 G3 B3 B2 G7 G6 G5 G4 G3 B3
CH x_1-
G7
CH x_2+
CH x_2- B5 B4 DE NA NA B7 B6 B5 B4 DE
CH x_3+
CH x_3- R1 R0 NA B1 B0 G1 G0 R1 R0 NA
Note: x = 1, 2, 3, 4…
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE “High” is less than 1920 DCLK or less than 1080 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.
Page 13 / 31
Tv M pixel
Tblk(v) Tdisp(v)
N L in e
Th
DE
RGB Line Invalid Data Line Line Line Line Line Invalid Data
N 1 2 3 4 N
Data
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH1 M-7 M-5 M-3 M-1
Invalid Data
1 3 5 7 9 11 M-5 M-3 M-1
Invalid Data
1 3
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH2 M-6 M-4 M-2 M
Invalid Data
2 4 6 8 10 12 M-4 M-2 M
Invalid Data
2 4
T420HW09 V1 Product Specification
Rev.0 2
3.5 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
t1 t2 t5 t6 t7
t3 t4
Backlight on / off
control signal
( VBLO N ) GND
t8 t9
CM O S Interface Signal
G ND
Values
Parameter Unit
Min. Type. Max.
t1 0.4! ---! 30! ms
t2 0.1! ---! 150! ms
t3 450! ---! ---! ms
*1
t4 0 ! ---! ---! ms
t5 0! ---! ---! ms
*2
t6 ---! ---! --- ! ms
t7 500! ---! ---! ms
t8! 10! ---! 50! ms!
t9! 0! ---! ---! ms!
Note:
(1) t4=0 : concern for residual pattern before BLU turn off.
(2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
(3) When CMOS Interface is N.C. (no connection), opened in Transmitted end, T8 timing spec can be negligible
ON 2 - 5.5 -
On/Off control voltage VBLON VDDB=24V VDC
OFF 0 - 0.8 -
External PWM
I_EPWM VDDB=24V - - 2 mADC -
Control Current
External PWM Duty
D_EPWM VDDB=24V 10 - 100 % 3
ratio
External PWM
F_EPWM VDDB=24V 140 180 240 Hz -
Frequency
10%
Power Input for BLU
(VDDB)
T1 T2 T5
VDDB(typ.)*0.8
Value
Parameter Units
Min Typ Max
T1 20 - - ms
T2 500 - - ms
T3 250 - - ms
T4 0 - - ms
T5 1 - - ms
T6 - - 10 ms
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of φ and θ equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 3200 4000 -- 1
2
Surface Luminance (White) LWH 320 400 -- cd/m 2
Luminance Variation δWHITE(9P) -- -- 1.33 3
Response Time (G to G) Tγ -- 6.5 -- Ms 4
Color Gamut NTSC 72 %
Color Coordinates
Red RX 0.640
RY 0.330
Green GX 0.281
GY 0.590
Typ.-0.03 Typ.+0.03
Blue BX 0.144
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle 5
x axis, right(φ=0°) θr -- 89 -- degree
x axis, left(φ=180°) θl -- 89 -- degree
y axis, up(φ=90°) θu -- 89 -- degree
y axis, down (φ=270°) θd -- 89 -- degree
Note:
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 11mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, δWHITE is defined (center of Screen) as:
δWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time T is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
T is determined by 10% to 90% brightness difference of rising or falling period. (As illustrated)
The response time is defined as the following figure and shall be measured by switching the input signal for
“any level of grey(bright) “ and “any level of gray(dark)”.
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%
100%
90%
Photodetector
Output
T (F) T (R)
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG3.
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T420HW09 V1. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 983.0 mm
Vertical 576.0 mm
Outline Dimension
Depth (Dmin) 35.5 mm to rear
Weight 9526 g
Front View
Back View
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
AU Optronics
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
QTY : 7
T420HW09 V1
97.42T14.XXX
!"#$%&'()*+,-./%012%
!"#$%&'()*+,-./%012%
!"#$%&'
3)$45'6%$+7%
3)$45'6%$+7%
3)$45'6%7'"%
3)$45'6%7'"%
3)$45'6%(':6%
3)$45'6%(':6%
(')'('*+,&%%
8"#$%,%!%#197'6%
8"#$%,%!%#197'6%
Specification
Item Packing Remark
Qty. Dimension Weight (kg)
2 Pallet 1 1140(L)*1060(W)*138(H) 16
3 Boxes per Pallet 8 boxes/pallet
4 Panels per Pallet 24pcs/pallet
Pallet after packing 24 1140(L)*1060(W)*1438(H) 320
Stretch film
Corner angle
Pallet
11. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied
to module. And the case on which a module is mounted should have sufficient strength so that
external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit
broken by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the
surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 and 35 at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.