INVT - AC Servo-DB100 - Manual - V3.0

Operational manual for INVT SV-DB100 AC Servo drives Preface
Preface
Thanks for using AC servo drive of the permanent magnet synchronous motor (hereinafter
called “servo drive”) from Shenzhen INVT Electric Co., Ltd. Please carefully read and master
the user’s manual before proper use. Improper use may cause abnormal running or shorten its
service life or even directly damage the drive.
Please keep this manual carefully for later reference.
Operational manual for INVT SV-DB100 AC Servo drives Safety precautions
Safety precautions
The precautions related to safe operation are classified into “Warnings” and “Notes”.
Point out potential danger which, if not avoided, may cause

physical injury or death.
Point out potential danger which, if not avoided, may result in mild
or moderate physical injury and damage to the equipment. It’s
also available to warn about unsafe operations.
In some cases, even the content described in “Note” may also cause serious accidents. So
please follow these important precautions in any situations.
Warning signs are presented on the sides of the servo drive. Please follow these instructions
when using the servo drive.
Warning signs:
Danger
Read the manual and follow the safety instructions before use.
Touch current may be over 3.5mA,Must be grounded before operation.
High Voltage
Do not touch terminals within 15 minutes after disconnecting the power. Risk
of electric shock.
High Temperature
Do not touch heat sink when power is ON. Risk of burn.
Please pay attention to the following safety precautions during installation, wiring, operation,
maintenance and inspection.
Installation:
Please use the servo drive and servo motor with the instructed
combination mode. Otherwise it may cause malfunction or even
fire of the equipment.
Never expose the product to an environment containing moisture,
corrosive gas, or flammable gas. Otherwise it may cause electrical
shock or fire.
Wiring:
Only qualified electricians are allowed to carry out the wiring.
Otherwise there is danger of electrical shock or fire.
The grounding terminals of the drive and motor must be
grounded with proper techniques. Otherwise there is danger of
electrical shock.
Do not touch the conductive components directly. Do not connect
the output lines of the drive with the enclosure. Avoid short circuit
of the output lines. Otherwise there is the danger of electrical
shock or short-circuit.
Ensure the installation of available overcurrent protector, leakage
protector and E-stop devices after distribution. Otherwise there
may be danger of electrical shock, injury and fire.
Redistribute the drive in at least 15 minutes after disconnecting
the power supply.
Make sure the voltage of the AC power supply equals to the rated
voltage of the servo drive. Otherwise there is danger of injury, fire
and damage to the drive.
Never connect the input power lines to the output terminals as
this will damage the drive.
Never conduct voltage withstand test on the drive or its
connection wires as this will cause damage to the drive.
Connect the drive and motor with correct phase sequence.
Otherwise it may cause malfunction or damage the drive.
Operation:
Please de-coupled the load from the drive before the trial
operation for the avoidance of accidents.
Check that the supply power of the drive can be disconnected
with the E-stop switch all the time before running.
Verify and adjust all parameters before running. Otherwise the
drive may run abnormally or act unexpectedly due to the load.
Do not touch the radiator or the external braking resistor during
running. They may become very hot and burn fingers.
Maintenance and inspection:

Before doing any inspection and maintenance, be sure to
disconnect the power supply, wait for 15 minutes and then
confirm with a multimeter. Otherwise electric shock may occur.
Only qualified electricians are allowed to inspect the servo
drive. Otherwise electric shock may occur.
Operational manual for INVT SV-DB100 AC Servo drives Content
Content
Preface............................................................................................................................................I
Safety precautions.......................................................................................................................II
Content ..........................................................................................................................................1
1 General .......................................................................................................................................1
1.1 General technical specifications ....................................................................................1
1.2 Nameplate of the servo drive.........................................................................................4
1.3 Illustration of the nameplate ..........................................................................................4
1.4 Power specification ........................................................................................................5
1.5 Illustrations of every parts of the servo drive ................................................................6
1.6 External dimensions and installations sizes of the servo drive ....................................6
2 Unpacking inspection ..............................................................................................................8
3 Installation .................................................................................................................................9
3.1 Environmental Requirement ..........................................................................................9
3.1.1 Temperature ......................................................................................................9
3.1.2 Relative humidity ...............................................................................................9
3.1.3 Altitude ...............................................................................................................9
3.1.4 Other environment requirements ....................................................................10
3.2 Installation of the servo drive .......................................................................................10
3.2.1 Installation........................................................................................................10
3.2.2 Installation direction and spacing.................................................................... 11
3.2.3 Avoid intrusion of foreign objects ....................................................................12
4 Signal and wiring ....................................................................................................................13
4.1 System configuration ...................................................................................................14
4.1.1 Connection diagram of the servo drive and external equipment ...................14
4.1.2 Cable diameter selection ................................................................................14
4.1.3 EMI filter selection ...........................................................................................15
4.1.4 Braking resistor selection................................................................................16
4.2 Wiring of the main circuit (Plug X1 and X2) ................................................................17
4.2.1 Overview..........................................................................................................17
4.2.2 Wiring diagram of single phase 230V power input ........................................18
4.2.3 Wiring diagram of three-phase 230V power input..........................................19
4.2.4 Wiring diagram of three-phase 400V power input..........................................20
4.3 Wiring of the encoder (plug CN2)................................................................................21
4.3.1 Overview..........................................................................................................21
4.3.2 CN2 pin arrangement and signal definition of the servo drive.......................21
4.4 Connection with the PC or HOST (CN3 plug).............................................................22
4.5 I/O signal wiring (CN1 connector) ...............................................................................23
1
4.5.1 Overview..........................................................................................................23
4.5.2 CN1 pin arrangement and signal explanation ................................................24
4.5.3 Standard wiring of the position control mode .................................................34
4.5.4 Standard wiring of the speed control mode....................................................35
4.5.5 Standard wiring of the torque control mode ...................................................36
4.5.6 Detailed instruction of the input and output of CN1 .......................................37
4.6 Wiring of the electromagnetic brake............................................................................43
5 Running and operation ..........................................................................................................44
5.1 Running ........................................................................................................................44
5.1.1 First powering on.............................................................................................44
5.1.2 Self-test before running of the servo ..............................................................45
5.1.3 Parameter setting before running the servo...................................................45
5.1.3 Trial jogging .....................................................................................................46
5.1.4 Running at the position control mode.............................................................46
5.1.5 Running at the speed control mode................................................................47
5.1.6 Running at the torque control mode ...............................................................48
5.1.7 Parameter setting before running the servo...................................................49
5.1.8 Servo enabling ................................................................................................50
5.1.9 Coast to Stop / DEC to Stop of the servo .......................................................50
5.1.10 Sequence diagram ........................................................................................52
5.2 Display and operation ..................................................................................................57
5.2.1 Display .............................................................................................................57
5.2.2 State monitoring mode ....................................................................................58
5.2.3 Parameter setting ............................................................................................60
5.2.4 Auxiliary functions............................................................................................66
5.2.5 Alarm display ...................................................................................................67
5.2.6 Alarm clearance...............................................................................................68
6 Detailed parameter description.............................................................................................69
6.1 Basic parameters (FP0 group parameters).................................................................69
6.1.1 Basic control ....................................................................................................69
6.1.2 Position control ................................................................................................76
6.1.3 Speed and torque control................................................................................79
6.2 Self-turning control parameters (FP1 group parameters)...........................................88
6.2.1 Inertia identification(Automatic gain) ..............................................................88
6.2.2 Adaptive vibration control................................................................................90
6.3 Motor control parameters (FP2 group parameters) ....................................................92
6.3.1 Gain .................................................................................................................92
6.3.2 Gain switching .................................................................................................94
2
6.3.3 Special motor control.......................................................................................96

6.4 I/O management parameters (FP3 group parameters) ..............................................96
6.4.1Digital input .......................................................................................................96
6.4.2 Analog input / output adjustment ....................................................................97
6.4.3 Switch input / output settings ........................................................................100
6.5 Extension and application (FP4 group parameters) .................................................103
6.5.1 Communication setting..................................................................................103
6.5.2 Alarm threshold setting..................................................................................106
6.6 Factory parameters (FP9 group parameters) ...........................................................107
6.7 State monitoring .........................................................................................................108
7 Gain adjustment....................................................................................................................114
7.1 General method for adjusting parameters ................................................................ 114
7.1.1 Adjustment of the gain of the position loop .................................................. 116
7.1.2 Adjustment of the gain of the speed loop ..................................................... 117
7.1.3 Adjustment of the gain of the torque loop..................................................... 119
7.2 Suppression of mechanical resonance .....................................................................120
7.3 Gain switching function ..............................................................................................121
8 Communication function .................................................................................................... 122
8.1 General.......................................................................................................................122
8.2 Topological structure ..................................................................................................122
8.2.1 Communication with single set .....................................................................122
8.2.2 Communication with multiple sets ................................................................122
8.3 Communication protocol ............................................................................................123
8.3.1 Protocol Content............................................................................................123
8.3.2 Protocol instructions ......................................................................................123
8.3.3 Communication Protocol Format ..................................................................124
8.3.4 Command code and the communication data instructions ..........................125
8.3.5 Error checkout of the communication frame ................................................131
8.3.6 Address definition of communication data....................................................132
8.3.7 Fault Responses ...........................................................................................134
9 Fault processing .................................................................................................................. 136
9.1 Meanings of the fault alarm codes and countermeasures........................................136
9.2 Meanings of the warning codes.................................................................................139
Appendix A List of function parameters .............................................................................. 140
Appendix B Signal arrangement diagram ........................................................................... 147
B.1 CN1 pin signal arrangement: ....................................................................................147
3
Appendix C Plug signal of servo motor............................................................................... 149

C.1 Plug of the motor .......................................................................................................149
C.1.1 Below and including 750: .............................................................................149
C.1.2 Above 750W..................................................................................................149
C.2 Plug of encoder wire..................................................................................................149
C.2.1 Below and including 750W ...........................................................................149
C.2.2 Above 750W..................................................................................................150
Appendix D Wiring examples ................................................................................................ 152
D.1 Connection with Panasonic FPG-C32T ......................................................................... 152
D.2 Connection with Panasonic FP2-PP22 (AFP2434)..................................................153
D.3 Connection with Panasonic FP2-PP2 (AFP2430)....................................................154
D.4 Connection with Yokogawa PLC F3YP14-ON/F3YP18-ON ....................................155
D.5 Connection with Yokogawa PLC F3NC32-ON/F3NC34-ON....................................156
D.6 Connection with Omron CS1W-NC133/233/433......................................................157
D.7 Connection with Omron CJ1W-NC133/233/433 ......................................................158
D.8 Connection with Mitsubishi QD75D1 ........................................................................159
D.9 Connection with Mitsubishi FX-1PG .........................................................................160
D.10 Connection with Mitsubishi FX2N-1PG ..................................................................161
4
Operational manual for INVT SV-DB100 AC Servo drives General
1 General
1.1 General technical specifications
The standard specifications of the AC permanent magnet synchronous servo drive are listed in
the table below:
Table 1-1 Standard specifications of servo drive
Specifications
Servo drive
200W~400W 0.75kW~2.0kW 3.0kW~5.5kW
Voltage Single/3-phase Single/3-phase 3-phase
degree 230V/50Hz 230V/50Hz 400V/50Hz
Input
AC
Power supply for voltage AC 230V±15%
400V±15%
the main circuit range
Input
frequency 47Hz~63Hz 47Hz~63Hz
range
Voltage Single phase
Single phase 230V/50Hz
degree 400V/50Hz
Input
AC
Power supply for voltage AC 230V±15%
400V±15%
the control circuit range
Input
frequency 47Hz~63Hz 47Hz~63Hz
range
Voltage DC 12V~24V
Allowable
Power supply for voltage ±10%
interfaces fluctuation
Power Above 500mA (the local 24V can only provide
capacity 100mA current)
Control method Vector control, SVPWM
Position control mode, speed control mode and
Control mode
torque control mode
Dynamic brake Yes
-1-
Specifications
Servo drive
200W~400W 0.75kW~2.0kW 3.0kW~5.5kW
Built-in braking resistor, as well as the external
Regenerative braking unit
braking resistor can be connected
AC reactor None
Input 13 ways of optical coupling isolation input
Switch signal
Output 7 ways of open-collector output
Input 2 ways, range: DC -10V~+10V
Analog
Output 2 ways, range: DC 0V~+10V
Input 2 ways, differential input or open-collector input
4 ways, 3 ways of encoder A/B/Z phase frequency
Pulse
Output division differential output, 1 way of Z phase
open-collector output
Protection from overcurrent, overvoltage, overload,
overheating, encoder fault, regeneration fault,
Protection functions
undervoltage, overspeed and high tracking error
and so on
Input pulse 500kHz (differential input)
frequency 200kHz (open-collector input)
Positioning
A/B orthogonal pulse
feedback
Resolution: 10000 pulses/rev
pulse
Pulse
Electronic gear A/B：A=1~65535 and B=1~65535
amplification
1/50<A/B<500
range
Positioning
Position control ±1 pulse
accuracy
Setting the
range for
reaching the ±10 pulses
designated
position
Range of fault set within the range of ±5 revs
Torque Set via the parameter or external analog input of
control range DC 0~±10V
-2-
Specifications
Servo drive
200W~400W 0.75kW~2.0kW 3.0kW~5.5kW
Max torque: 300% of rated torque
Frequency
1000Hz
response
The Max speed is 5000r/min, the Min speed is
Speed control
0.1r/min, and the speed regulation range is
range
1:50000
Analog speed
command DC 0~±10V/Max rotation speed
Speed control
input
Speed
fluctuation ±0.03%
rate
Set via the parameter or external analog input of
Torque
DC 0~±10V
control range
Max torque: 300% of rated torque
Analog torque
command DC 0~±10V/Max torque
input
Torque control Torque
Below ±10%
linearity
Speed control Set via the parameter or external analog input of
range DC 0~±10V (Max rotation speed)
Allowable Max inertia 30 times
RS232 Host 1: 1 communication
Communication
RS485 Host 1: n communication, n≤32
Structure Natural cooling: IP20 Air cooling: IP20
Operating
Environment 0~45℃
temperature
Storage
-20~80℃ (without freezing)
temperature
Humidity Operating/storage: ≤90%RH (non-condensation)
Other Indoor (without direct sunshine), free from
-3-
Specifications
Servo drive
200W~400W 0.75kW~2.0kW 3.0kW~5.5kW
environmental corrosive, flammable gasses, oil mist, dust
conditions
Allowable
Should be derated if the altitude is higher than
operating
1000m
altitude
2
≤5.88m/s , 10~60Hz (not allowed to run at the
Vibration
resonant point)
1.2 Nameplate of the servo drive
Fig. 1-1 Nameplate of the servo drive
1.3 Illustration of the nameplate
Fig. 1-2 Meanings of the model

Field Meaning
A SV: (INVT) Servo system products
st
B DB100: 1 generation of simple products
Power degree:
0R2: 200W 0R4: 400W 0R7: 750W 1R0: 1.0kW
C
1R5: 1.5kW 2R0: 2.0kW 3R0: 3.0kW 4R4: 4.4kW
5R5: 5.5kW
D Input voltage degree:
-4-
Field Meaning
05: 48VDC 08: 80VDC D1: 110VDC 1: 110VAC
2: 230VAC 4: 400VAC 6: 660VAC
Encoder type:
1: 2500-wire 2: 2500-wire 3: 17-bit 4: 17-bit

standard increment mode one-loop multiple-loop
E
increment mode absolute value absolute value
5: Rotary
transformer
Communication:
F
R: RS485 C: CANOPEN P: PROFIBUS-DP
Reserved space
G Products for special use and specific OEM product with protection
Default: standard product
1.4 Power specification

The power of each model is listed in the table below:
Table 1-2 Power specification of every model
Input Output
Models Capacity Rated current
Voltage (V) Power (kW)
(kV/A) (A)
SV-DB100-0R2-2 0.5 Single /3-phase 230 0.2 1.8
SV-DB100-1R5-2 2.5 3-phase 230 1.5 8.0
SV-DB100-2R0-2 3.5 3-phase 230 2.0 10.0
SV-DB100-1R0-4 1.9 3-phase 400 1.0 3.0
SV-DB100-1R5-4 2.9 3-phase 400 1.5 4.5
SV-DB100-2R0-4 3.9 3-phase 400 2.0 5.5
SV-DB100-3R0-4 4.8 3-phase 400 3.0 8.0
SV-DB100-4R4-4 6.2 3-phase 400 4.4 11.0
SV-DB100-5R5-4 7.5 3-phase 400 5.5 14.0
-5-
1.5 Illustrations of every parts of the servo drive
Fig. 1-3 Illustrations of every parts of 200W~5.5kW servo drives
1.6 External dimensions and installations sizes of the servo drive
Fig. 1-4 External dimensions of 100W~5.5kW servo drive
-6-
Table 1-3 External dimensions and installations sizes

External dimensions Installation sizes
Installation
Models H W D A B1 B2
hole (mm)
(mm) (mm) (mm) (mm) (mm) (mm)
SV-DB100-0R2-2
160 68 186 56 150 194 5
SV-DB100-0R4-2
SV-DB100-0R7-2
SV-DB100-1R0-2
SV-DB100-1R5-2
SV-DB100-2R0-2 160 98 186 86 150 194 5
SV-DB100-1R0-4
SV-DB100-1R5-4
SV-DB100-2R0-4
SV-DB100-3R0-4
SV-DB100-4R4-4 230 110 186 98 219 264 5
SV-DB100-5R5-4
-7-
Operational manual for INVT SV-DB100 AC Servo drives Unpacking inspection
2 Unpacking inspection
● Don’t install or use any servo drive that is damaged or has fault parts,
otherwise physical injury may occur.
Check the following items after unpacking the servo drive and servo motor.
1． Inspect the entire exterior of the servo drive and servo motor to ensure there are no
scratches or other damage caused by the transportation.
2． Ensure there is operational manual in the packing box.
3． Inspect the nameplate and ensure it is the right product.
4． Ensure the optional parts are the ordered ones.
Please contact the local agent if there is any damage to the servo drive and servo motor or
optional parts.
-8-
Operational manual for INVT SV-DB100 AC Servo drives Installation
3 Installation
● Only qualified electricians are allowed to operate on the drive device/system.

Ignoring the instructions in “warning” may cause serious physical injury or death or
property loss. Only qualified electricians are permitted to design, install,
commission and operate on the device/system.
● Connect the input power lines tightly and permanently. And ground the device with
proper techniques.
● Even when the servo drive is stopped, dangerous voltage is present at the
terminals:
- Power Terminals: R, S, T, r and t;
- Motor Connection Terminals: U, V and W;
- Regenerative Braking Resistor Connection Terminals: B1, B2 and B3.
● Stop the drive and disconnect it from the power line. Wait for 15 minutes to let the
drive discharge and then begin the installation.
● Install the servo drive on the non-flammable materials (such as metal) to prevent
fire.
● Install a cooling fan to ensure the air temperature is lower than 45°C when two
drives are needed in one cabinet. Otherwise fire or damage to the devices may
occur.
3.1 Environmental Requirement

3.1.1 Temperature
Environment temperature range: 0°C ~ +45°C.
3.1.2 Relative humidity

RH≤ 90%.
No condensation is allowed.
3.1.3 Altitude
The servo drive can run at the rated power if the installation site is less than 1000m (including
1000m) above the sea level. But it has to derate if the altitude exceeds 1000m. See the
-9-
following figure for details:
Figure 3.1 Relationship between output current and altitude
3.1.4 Other environment requirements

The servo drive can not bear fierce impact or shock. So the oscillation range should be less
2
than 5.88m/s (0.6g), 10Hz~60Hz.
The servo drive should keep away from the electromagnetic radiation source.
The servo drive should keep away from water and condensation.
The servo drive should keep away from contaminative air, such as corrosive gas, oil mist and
conductive dust.
The servo drive should keep away from direct sunlight, oil mist, and steam and vibration
environment.
3.2 Installation of the servo drive

3.2.1 Installation
The drive can be rack mounted. On the rear panel of the drive, there are two M5 mounting
holes in the bottom left corner and top right corner to fix the drive tightly on a vertical plane.
Fig. 3-2 Mounting holes of the servo drive

The servo drive can be shelf mountable by mounting bracket.
-10-
Fig. 3-3 Schematic diagram of the shelf mounting form of the servo drive
3.2.2 Installation direction and spacing

Please install the servo drive vertically and keep sufficient space around it for ventilation. If
necessary, please fit a fan to control the temperature in the cabinet below 45℃ .
1) To install only one set:
Fig. 3-4 Installation of single servo drive

2) To install several sets:
-11-
Fig. 3-5 Installation of several servo drives
3.2.3 Avoid intrusion of foreign objects

1. When assembling the control cabinet, do not allow metal chips to intrude into the
servo drive.
2. Do not allow oil, water, metal chips and other foreign objects drop into the servo drive
through the gaps between the control cabinet or the fan.
3. When the control cabinet is installed in a place with harmful gas or dust, ventilation is
confirmedly required (to blow clean air into the control cabinet and keep the pressure
inside is higher than outside) to avoid these matters coming into the control cabinet.
-12-
Operational manual for INVT SV-DB100 AC Servo drives Signal and wiring
4 Signal and wiring
 Only qualified electricians are allowed to operate on the drive for the insurance
of a safe running of the servo drive.
 Never carry out any insulation or voltage withstand tests on the cables
connecting with the servo drive.
 Even if the servo drive is stopped, dangerous voltage is present at the input
power lines, DC circuit terminals and motor terminals. Wait for 15 minutes even
when the drive is switched off until is discharge before operation.
 Ground the grounding terminals of the drive with proper techniques. Otherwise
there is danger of electrical shock and fire.
 Never do wiring or other operations on the servo drive with wet hands.
Otherwise there is danger of electric shock
 Verify that the rated voltage of the servo drive equals to the voltage of the AC
power supply.
 The power wires and motor wires must be permanently fastened and
connected.
-13-
4.1 System configuration

4.1.1 Connection diagram of the servo drive and external equipment
Fig. 4-1 Connection diagram of the servo drive and external equipment
 Check to ensure the input power supply indicated on the nameplate is the same as
the grid before connecting the power supply of the drive.
 The electromagnetic contactor is used to switch on/off the power supply of the
main circuit of the servo drive. Do not use it to start/stop the servo drive.
 In the figure above, the built-in regenerative braking resistor is used as default. If
an external regenerative braking resistor is used, please refer to relevant wiring
diagram. The regenerative braking resistor must be mounted on non-flammable
materials, such as metal.
4.1.2 Cable diameter selection
-14-
Table 4-1 Cable diameter selection

Model Cable diameter of the main circuit
SV-DB100-0R1-2
0.75~2.0mm2
SV-DB100-0R2-2
AWG14 to AWG18
SV-DB100-0R4-2
SV-DB100-0R7-2
SV-DB100-1R0-2
SV-DB100-1R5-2
2.0mm2
SV-DB100-2R0-2
AWG14
SV-DB100-1R0-4
SV-DB100-1R5-4
SV-DB100-2R0-4
SV-DB100-3R0-4
3.5mm2
SV-DB100-4R4-4
AWG12
SV-DB100-5R5-4
Notes:
1. Cable diameter is the diameter of copper cables.
2
2. The diameter of the protective grounding wire: not less than 2.0mm (AWG14) for
2
100W~2.0kW models; not less than 3.5mm (AWG12) for 3.0kW~4.4kW models; not less than
2
5.3mm (AWG10) for 5.5 kW model.
4.1.3 EMI filter selection

Table 4-2 EMI filter selection
Drives EMI filters
SV-DB100-0R2-2 FLT-P04016L-B
SV-DB100-0R4-2
SV-DB100-0R7-2
SV-DB100-1R0-2
SV-DB100-1R5-2
SV-DB100-2R0-2
SV-DB100-1R0-4
SV-DB100-1R5-4
SV-DB100-2R0-4
SV-DB100-3R0-4
SV-DB100-4R4-4
-15-
Drives EMI filters

SV-DB100-5R5-4
Note: The EMI filter modules in the table means the filter product modules of INVT.
4.1.4 Braking resistor selection

Table 4-3 Braking resistor selection
Recommended
The allowed
Internal braking External
Drives external Minimum
resistors Braking
braking resistors
Resistors
SV-DB100-0R2-2 47Ω 80W 60Ω 200W 40Ω
SV-DB100-0R4-2 47Ω 80W 60Ω 400W 40Ω
SV-DB100-0R7-2 47Ω 80W 40Ω 750W 40Ω
SV-DB100-1R0-2 47Ω 80W 30Ω 1.0kW 25Ω
SV-DB100-1R5-2 20Ω 80W 20Ω 1.0kW 15Ω
SV-DB100-2R0-2 20Ω 80W 20Ω 1.0kW 15Ω
SV-DB100-1R0-4 100Ω 80W 80Ω 1.0kW 80Ω
SV-DB100-1R5-4 47Ω 80W 50Ω 1.0kW 47Ω
SV-DB100-2R0-4 47Ω 80W 50Ω 1.0kW 47Ω
SV-DB100-3R0-4 47Ω 80W 40Ω 2.0kW 30Ω
SV-DB100-4R4-4 47Ω 80W 40Ω 2.0kW 30Ω
SV-DB100-5R5-4 47Ω 80W 40Ω 2.0kW 30Ω
-16-
4.2 Wiring of the main circuit (Plug X1 and X2)

4.2.1 Overview
AC power supply
EMI filter
Breaker
MC
Fig. 4-2 Wiring diagram of the main circuit
-17-
4.2.2 Wiring diagram of single phase 230V power input
MC
· The user is required to make this emergency
ON OFF ALM stop protection circuit.
· Fit surge absorbing devices on both ends of
the electromagnetic contactor winding.
R
MC
Breaker S · The input voltage range of main circuit and
control circuit is 220V±15%
· Please connect terminal R with terminal T.
T
X1
U · Connect the output U, V, and W of the drive to

the servo motor correctly according to the
phase sequence of the motor cable of the
V servo motor. Wrong phase sequence will
· cause drive fault.
· Do not disconnect the short circuit wire
W between B2 and B3 unless an external
regenerative braking resistor is used.
· When an external regenerative braking resistor
B1 is used, disconnect the short circuit wire
between B2 and B3, and connect it according
Motor to the dashed in the figure.
B2
B3
X2
Yellow/green · Be sure to ground the servo drive to avoid
E-stop RY accident of electrical shock.
Surge absorber · Please refer to section 4.6 for connection of

DC the electromagnetic brake.
24V±10% · The electromagnetic brake uses 24V power
Fuse supply which should be provided by the user.
CN1 Moreover, it must be isolated with the 12-24V
power supply which is used for the control
ALM signal.
ALM · Pay attention to the connection of the
DC 12~24V
freewheeling diode. Reversed polarity may
(±10%) damage the drive.
COM-
Fig. 4-3 Wiring diagram of single phase 230V power input
-18-
4.2.3 Wiring diagram of three-phase 230V power input
Fig. 4-4 Wiring diagram of three-phase 230V power input
-19-
4.2.4 Wiring diagram of three-phase 400V power input

ON OFF ALM
· The user is required to make this emergency
stop protection circuit.
Breaker · Fit surge absorbing devices on both ends of
the electromagnetic contactor winding.
R
EMI filter
MC
· The input voltage range of main circuit and
S control circuit is 380V±15%
t
X1
U
· Correctly connect to output U, V, and W of the
drive according to the phase sequence of the
V motor cable of the servo motor. Wrong phase
sequence will cause drive fault.
· Do not disconnect the short circuit wire between
W B2 and B3 unless an external regenerative
braking resistor is used.
· When and external regenerative braking
B1 resistor is used, disconnect the short circuit wire
between B2 and B3, and connect it according to
Motor the dashed in the figure.
B2
B3
X2
Yellow/green · Be sure to ground the servo drive to avoid
E-stop RY accident of electrical shock.
Surge absorber
DC 24V±10% · Please refer to section 4.6 for connection of
the electromagnetic brake.
Fuse CN1 · The electromagnetic brake uses 24V power
supply which should be provided by the user.
ALM Moreover, it must be isolated with the 12-24V
power supply which is used for the control
DC ALM
signal.
12~24V · Pay attention to the connection method of the
(±10%) freewheeling diode. Reversed polarity may
COM- damage the drive.
Fig. 4-5 Wiring diagram of three-phase 400V power input
-20-
4.3 Wiring of the encoder (plug CN2)

4.3.1 Overview
Fig. 4-6 Wiring of the encoder signal
4.3.2 CN2 pin arrangement and signal definition of the servo drive
Fig. 4-7 CN2 pin arrangement

Table 4-2 CN2 signal definition table
CN2 pin No. Definition Cable color
1 V+ Black
2 W+ Brown
3 A+ Red
-21-
CN2 pin No. Definition Cable color

4 A- Red and white
5 5V Purple
6 U+ Orange
7 V- Black and white
8 W- Brown and white
9 B- Blue
10 B+ Blue and white
11 U- Orange and white
12 GND Purple and white
13 Z- Green
14 Z+ Green and white
15 / /
4.4 Connection with the PC or HOST (CN3 plug)

The servo drive provides two kinds of communication interface: RS232 and RS485, both are
drawn out via the plug CN3.
CN3 pin arrangement and signal definition:
6 3
1
4
7
2
8 5
Fig. 4-8 CN3 pin arrangement

Table 4-3 CN3 signal definition table
CN3 pin No. 1 2 3 4 5 6 7 8
Definition RXD GND TXD CANL / CANH RS485- RS485+
-22-
4.5 I/O signal wiring (CN1 connector)

4.5.1 Overview
Fig. 4-9 Input/output signal connection
-23-
4.5.2 CN1 pin arrangement and signal explanation

4.5.2.1 CN1 terminal definition
Servo
16 SON
enabling
Speed
Switching
selection 2 Command
of the
1 MCH 17 SC2 /electrical 31 OCS pulse input
control
gear selection 1(selected)
mode
2
Speed
Power
reverse Command
supply of
2 COM+ 18 RPC /retention 32 SIGN+ pulse input
the control
pulse 2
signal +
clearance
Command
Forward
3 PSL 19 GND Signal ground 33 SIGN- pulse input
travel limit
2
Speed
selection 1
Reverse Analog input
4 RVL 20 VA+ 34 SC1 /electrical
travel limit 1
gear
selection 1
Analog Analog input Signal
5 VA- 21 AO1 35 GND
input 1 1 ground
Torque
Analog input Gain
6 TQC limit 22 PLL 36 PLC
inhabit switching
selection
Analog Command Zero
7 TA+ 23 PULSE+ 37 ZRS
input 2 pulse input 1 position
Command
Analog Command
8 TA- 24 PULSE- 38 OCP pulse input
input 2 pulse input 1
2(selected)
Breaker Analog output
9 BRK 25 AO2 39 EMG E-stop
release 2
-24-
Z phase
Local
10 CLA Alarm clear 26 OCZ collector 40 24V
24V
output
Position Z phase B phase
11 PLR 27 OZ- 41 OB+
arrival output output
Power
supply of Z phase B phase
12 COM- 28 OZ+ 42 OB-
the control output output
signal -
Torque A phase
13 LM 29 ZSO Zero speed 43 OA-
limit output
Servo A phase
14 RDY 30 SR Speed arrival 44 OA+
ready output
Servo
15 ALM
alarm
4.5.2.2 CN1 See the figure below for CN1 pin signals:
Fig. 4-10 CN1 pin signal diagram

4.5.2.3 Power signal
Table 4-6 Power signal table
Symbol Pin No. Name Function
It’s supplied by the drive. COM- is the ground terminal
24V power
24V 40 of the 24V power. Its capacity is 100mA. If the actual
supply
load is higher than this value, the user shall provide the
-25-

power supply by themselves.
The ground of the internal power supply (except the
24V power supply) of the servo drive, it is also the
Signal
GND 19, 35 ground of the phase Z open-collector signal of the
ground
encoder and the analog output signal. It is isolated with
COM-.
Positive If the DC power supply is provided by the user, the
pole of positive pole of the DC power supply must be
COM+ 2 external DC connected to this terminal.
power If the 24V power supply of the drive is used, the 24V
12V~24V terminal (pin 40) must be connected on this terminal.
Negative
Local 24V;
COM- 12 pole of the
Negative pole of the external power 12V~24V
power
Cassie The cassis of CN1 terminal is connected with that of
FG Cassie
ground the drive.
4.5.2.4 Digital input signals and their functions

Table 4-7 Function table of digital input signals
Pin
Symbol Name Function Mode
No.
When a fault alarm occurs, this terminal can
be short-connected with COM-. If the fault
condition is removed, the fault alarm display
will be cleared. If the fault condition is not
removed, the fault will be reported again.
CLA 10 Alarm clear P.S.T
Please remove the fault and short connect
this terminal with COM- again. In this way the
fault alarm display will be cleared.
Note: This terminal signal takes effect when
receiving a pulse.
When parameter FP3.41 (E-stop masking) is
Emergency
EMG 39 set as 1, i.e. Emergency stop terminal signal P.S.T
stop
is active, this terminal can be used to execute
-26-
Pin
No.
emergency stop function: after disconnecting
this terminal with COM-, the servo drive cuts
off the output, the servo motor coast to stop
and Emergency stop warning will occur. After
emergency stopping, even if this terminal
recovers short-circuit with COM-, it needs to
enable the servo to run the drive. If internal
servo enabling is used, it needs to switch on
the control power again and then activate the
internal servo enabling. This terminal signal
takes effect when receiving a pulse.
When parameter FP3.41 is set as 0,
Emergency stop terminal signal is invalid.
receiving a pulse.
When parameter FP0.03 (control mode
selection) is set as 3~5, this terminal can be
used to switch between different controls
modes. The corresponding relationships of
this terminal’s state and the control modes
are listed in the table below:
Control Value of MCH is MCH is
MCH 1 mode parameter disconnected connected with P.S.T
switching FP0.03 with COM- COM-
Position control Speed control
3
mode mode
Speed control Torque control
4
mode mode
Position control Torque control
5
mode mode
When parameter FP2.22 (gain switching
Gain
PLC 36 condition) is set as 0, i.e. manual gain P.S.T
switching
switching, this terminal can be used to switch
-27-
Pin
No.
gain. Parameter FP2.21 is used to select the
type of gain switching. See the explanation of
FP2.21 and FP2.22 for details.
In position control mode, this terminal can be
used to disable input of position pulse signal,
i.e. the inputted position pulse signal is
invalid.
When this terminal is short-circuited with
Pulse input
PLL 22 COM-, pulse input is disabled, and the servo P
disabling
is in locked state. When this terminal is
disconnected with COM-, pulse input is
allowed, and the servo can run.
receiving a pulse.
When parameter FP3.40 is set as 1, i.e. the
signal of travel limitation terminal is active,
this terminal can be used to execute forward
travel limitation function:
When this terminal is disconnected with
COM-, the forward speed will return to zero
immediately and a forward travel limitation
alarm will occur until the forward travel
Forward limitation terminal recovers short-circuit with
PSL 3 travel COM-. In the forward travel limitation, the P.S.T
limitation drive can automatically respond to the
reverse speed command. This terminal signal
takes effect when receiving a pulse.
In the speed mode and torque mode, the
servo is in zero speed clamp state.
In the position mode, the servo is in locked
state.
When parameter FP3.40 is set as 0, this
travel limitation terminal signal is invalid.
-28-
Pin
No.
In the speed mode, short connecting this
terminal with COM- can reverse the direction
of the internal speed command and analog
Speed speed command.
reversing/ In the position mode, short connecting this
RPC 18 retention terminal with COM- can clear the position P.S
pulse command pulse counter, the position
clearing feedback pulse counter, and the position
deviation pulse counter.
This terminal signal takes effect when
receiving a pulse.
When parameter FP3.40 (Travel limit switch
masking) is set as 1, i.e. the travel limitation
terminal signal is active, this terminal can be
used to execute reverse travel limitation
function:
COM-, the reverse speed will return to zero
immediately and a reverse travel limitation
alarm will occur until the forward travel
Reverse
limitation terminal recovers short-circuit with
RVL 4 travel P.S.T
COM-. In reverse travel limitation, the drive
limitation
can automatically respond to the positive
speed command. This terminal signal takes
effect when receiving a pulse.
In the speed mode and torque mode, the
servo is in zero speed clamp state.
In the position mode, the servo is in locked
state.
When parameter FP3.40 is set as 0, this
travel limit terminal signal is invalid.
-29-
Pin
No.
Speed Internal speed command (speed
option mode)/speed limit (torque mode) or electronic
SC1 34 1/electronic gear (position mode) is selected by
gear option combination of these two terminal signals as
1 listed in the table below (ON indicates SCX is
short-circuited with COM-, OFF indicates
SCX is open-circuited with COM- (X=1 or 2)):
Position
SC2 SC1 Speed/torque mode
mode P.S.T
Speed
Internal speed/speed Electronic
option OFF OFF
limit 1 gear 1
SC2 17 2/electronic
gear option OFF ON
limit 2 gear 2
2
ON OFF
limit 3 gear 3
ON ON
limit 4 gear 4
External servo enabling can be conducted by
this terminal: the drive is in servo enabling
state after this terminal is short-circuited with
COM-. After switching on the power, the
motor will run according to the command of
the drive. After this terminal is disconnected
with COM-, the drive will disconnect the
Servo output and the motor will stop. This terminal
SON 16 P.S.T
enabling signal takes effect when receiving a pulse.
COM-, internal servo enabling can be
conducted through parameter FP0.04. See
the explanation of parameter FP0.04 for
details.
Note:
After SON is short-circuited with COM-,
-30-
Pin
No.
please wait for at least 100ms before
entering any command pulse;
When SON is disconnected with COM-, the
position deviation counter is cleared off.
Try best to avoid to starting/stopping the
servo drive with this terminal continually. The
drive can be started/stopped with the zero
speed clamp terminal (ZRS). See function
description of terminal ZRS for details.
In the speed or position mode, if parameter
FP0.04=0, when this terminal is
short-circuited with COM-, the torque limit
command is external analog torque limit,
Torque limit when this terminal is disconnected with
TQC 6 P.S
selection COM-, the torque limit command is internal
torque limit, and the value is given by
parameter FP0.12. If parameter FP0.04=1,
the torque limit command is internal torque
limit, this terminal signal is inactive.
In the table above: the polarity of terminals SON, ZRS, CLA, PLL, and RPC can be reversed by
setting parameter FP3.00. See the explanation of FP3.00 in chapter 6.4.
4.5.2.5 Pulse input signals and their functions
Table 4-8 Function table of pulse input signals
OCP 38 Position In the position control mode, they are used as
PULSE+ 23 command the input terminals of the position command;
PULSE- 24 pulse input 1 In other control modes, this group of terminals is
OCS 31 inactive;
Position
SIGN+ 32 Allowed Max. input pulse frequency: 500kHz in
command
differential mode, 200kHz in open-collector
SIGN- 33 pulse input 2
mode.
4.5.2.6 Pulse input signals and their functions
Table 4-9 Function table of analog input signals
-31-

VA+ 20 Position
command
External analog input terminals. The input impedance
VA- 5 pulse
is 10kΩ. The input voltage range is -10V~+10V. A
input 1
voltage exceeding ±11V may damage the drive.
TA+ 7 Position
Refer to parameters of FP0.42, FP0.62 and FP3.20,
command
FP3.23.
TA- 8 pulse
input 2
4.5.2.7 Digital output signals and their functions

Table 4-10 Function table of digital output signals
When the servo drive is in normal state, this signal
output transistor is breakover. When the power supply
ALM 15 Servo alarm
is disconnected or the servo drive is in alarm state,
this signal output transistor switches off.
When the servo system is in torque limit, this signal
LM 13 Torque limit
output transistor is breakover.
Position When the position reaches to the command range,
PLR 11
reaching this signal output transistor is breakover.
When it comes into the brake releasing sequence and
Brake
BRK 9 needs to release the brake, this signal output
releasing
transistor is breakover.
When the control power and main power are applied
normally and the drive is not in alarm state, this signal
RDY 14 Servo ready
output transistor is breakover, it means the drive can
be started.
Speed When the speed reaches the range of speed setting,
SR 30
reaching this signal output transistor is breakover.
Zero When the speed reaches the range of zero speed,
ZSO 29
speed this signal output transistor is breakover.
4.5.2.8 Digital output signals and their functions
Table 4-11 Function table of encoder output signals
-32-

OA+ 44 Phase A  Output the frequency divided encoder signal,
OA- 43 output comply with the standard of TIA/EIA-422-B;
OB+ 41 Phase B  The output phase A pulse and phase B pulse is
OB- 42 output still orthogonal. When it rotates forward, phase
OZ+ 28 B leads phase A by 90º. When it rotates in

reverse, phase A leads phase B by 90º.
 The frequency division coefficient of phase A
and phase B can be set through parameter
OZ- 27 Phase Z FP0.06 and FP0.07. Frequency division with
output any integer and decimal fraction is allowable
but frequency multiplication is not allowed;
 The output signals have no isolation.
Output the open-collector signal of phase Z,
OCZ 26
without isolation.
4.5.2.9 Analog output signals and their functions
Table 4-12 Function table of analog output signals
Its output function can be defined by setting
Analog
AO1 21 parameter of FP3.30. The range and deviation
output 1
can be set via parameters FP3.31 and FP3.34.
Its output function can be defined by setting
Analog
AO2 25 parameter of FP3.32. The range and deviation
output 2
can be set via parameters FP3.33 and FP3.35.
-33-
4.5.3 Standard wiring of the position control mode
Fig. 4-11 Standard wiring of the position control mode
-34-
4.5.4 Standard wiring of the speed control mode
Fig. 4-12 Standard wiring of the speed control mode
-35-
4.5.5 Standard wiring of the torque control mode
Fig. 4-13 Standard wiring of the torque control mode
-36-
4.5.6 Detailed instruction of the input and output of CN1
4.5.6.1 Wiring of ON-OFF input circuit
Connection diagram when the power supply is self-provided by user:
Fig. 4-14 Wiring diagram of ON-OFF input circuit (power supply is self-provided by user)
Connection diagram when the local power supply is used:
Fig. 4-15 Wiring diagram of ON-OFF input circuit (local power supply)
 The ON-OFF input circuit can be connected with mechanical switch connection
and the open-collector connection of audion shown in the figure.
 The user can use either the 24V power supply (it only can provide 100mA current)
of the servo drive or 12V~24V power supply provided by the user.

4.5.6.2 Wiring of the pulse input circuit
Connect method 1: the differential connection
-37-
Fig. 4-16 Wiring diagram of differential pulse input circuit

◆ The maximum frequency of input pulse is 500kHz and the input signal voltage
is ±5v;
◆ With the best anti-noise capability, this signal transmit method is
recommended as the preferred.
Connection method 2: the open collector circuit 1
The control module is NPN (the common negative pole):
Fig. 4-17 Wiring diagram of the open collector circuit 1(NPN)

The control module is PNP module (the common positive pole):
Fig. 4-18 Wiring diagram of the open collector circuit 1(PNP)

◆ The Max. input pulse frequency is 200kHz; apply the local 24v power supply((it only
can provide 100mA current)) or the user-provided 24v power supply without the
current-limiting resistor. Generally, most of Japanese PLC (such as Mitsubishi,
Panasonics and OMRON) is NPN module, while most of European PLC (such as
-38-
Siemens) is PNP module. The above figure is external 24V power supply connection.
If the internal power supply is needed, connect the pin of the positive terminal of 24V
power supply and the pin of 24V power supply (the 40 pins of CN1)of the drive and
connect the pin of the negative terminal of 24V power supply and COM-(the 12 pins of
CN1).
Connection method 3: the open collector circuit 2
The control module is NPN (the common negative pole):
Fig. 4-19 Wiring diagram of the open collector circuit 2(NPN)

The control module is PNP (the common positive pole):
Fig. 4-20 Wiring diagram of the open collector circuit 2(PNP)

◆ The Max. input pulse frequency is 200kHz; apply the local 24v power supply((it only
can provide 100mA current)) or the user-provided 24v power supply with the
current-limiting resistor(the resistance is selected as the below table). Generally, most

of Japanese PLC (such as Mitsubishi, Panasonics and OMRON)is NPN module,
while most of European PLC (such as Siemens)is PNP module. The above figure is
external 24V power supply connection. If the internal power supply is needed,
connect the pin of the positive terminal of 24V power supply and the pin of 24V power
supply (the 40 pins of CN1)of the drive and connect the pin of the negative terminal of
24V power supply and COM-(the 12 pins of CN1).
-39-
For all the 3 methods, shielded twisted-pair must be used and the length must be less than 3m.
4.5.6.3 Wiring of the analog input circuit
Fig. 4-21 Wiring diagram of the analog input circuit

 There are two analog input circuits VA and TA. The input impedance is 10kΩ. The
input voltage range is -10V~+10V. If the voltage is higher than ±11V, the circuits
may damage.
4.5.6.4 Wiring of ON-OFF output circuit
Connection diagram when the power supply is self-provided by user:
Fig. 4-22 Wiring diagram of ON-OFF output circuit (power supply is self-provided by user)
Connection method when the local power supply is used:
-40-
Fig. 4-23 Wiring diagram of ON-OFF output circuit (local power supply)
 There are 7 digital output circuits in total and all of them adopt the open-collector
output as shown in the figure. They can be used to drive the relay coil or optical
coupled load. The loading capacity is as shown in the figure.
 When inductive loads such as relay coil are connected, a freewheel diode must be
fitted as shown in the figure. Otherwise the drive will be damaged.
 The local 24V power supply only can provide 100mA current. If the actual load
current is larger than 100mA, the user should provide the power supply by
themselves. The recommended capacity is greater than 500mA.

4.5.6.5 Wiring of the frequency division output circuit of the encoder feedback signal:
Fig. 4-24 Wiring diagram of the frequency division output circuit of the differential encoder
feedback signal
Open-collector mode:
-41-
Fig. 4-25 Wiring diagram of the frequency division output circuit of the open-collector encoder
feedback signal
 Phase A and B of the encoder only provides differential output signal, phase Z
provides differential output and open-collector output signals.
 For differential output signal, to use AM26C32 or equivalent differential receiving
chip and be sure to fit a terminal matching resistor of about 220Ω is
recommended .
 For the phase Z signal of open-collector output, as the signal pulse width is very
narrow, the user shall use high speed optical coupler to receive this signal.
 Both kinds of output circuits have no isolation.
4.5.6.6 Wiring of the analog output circuit
Fig. 4-26 Wiring diagram of the analog output circuit

There are two analog output circuits in all. The output voltage range is 0 – 10V. The Max output
current is 3mA.
-42-
4.6 Wiring of the electromagnetic brake

In the case the servo motor is used in a vertical shaft, the electromagnetic brake can be used to
prevent or keep the falling speed of heavy objects when the servo drive is powered off. The
connection of the electromagnetic drive is shown in the figure below:
Servo drive Note: Braking winding should use special power supply
24V+ 24V. Do not share the power supply with the control
When the local 24V power 40 power and the power supply for relay
supply of the drive is used,
connect the dashed in the
figure and remove the RY E-stop
RY Motor
external power supply.
Surge
BRK 9 + DC24V absorber
+
- - Special power
12V~24V Fuse
COM- 12 supply for the
（5A）
braking winding
Fig. 4-27 Wiring of the electromagnetic brake

 The user needs to prepare a special power supply for this electromagnetic brake.
Do not share the power supply with the power which is used for control signal;
 in the figure is the relay coil. Please note the direction of the diode;
 The electromagnetic brake is used for keeping the speed. It cannot be used for
normal stop;
 Though the electromagnetic brake has the function to prevent or keep the falling
speed of heavy objects, the user must install an external braking device at the
same time;
 BRK signal works when the drive stops or fault occurs if the power supply is
connected or the servo drive is running. Please refer to chapter 5.1.10 for the
sequence.
BRK signal can be closed through the setting of FP3.57. Please refer to FP3.57 for detailed
information.
-43-
Operational manual for INVT SV-DB100 AC Servo drives Running and operation
5 Running and operation
5.1 Running
5.1.1 First powering on
Check followings before powering on:
1) Wiring
 The power supply of the servo drive (R, S, T, r and t) should be connect with proper
techniques;
 The output phase of the servo drive (U, V and W) should be the same as that of the
cables of the servo drive;
 There is no short circuit between the output of the servo drive (U, V and W) and the
input power supply (R, S and T);
 All wiring comply with the standard wiring shown in section 4.5.3~4.5.5;
 Ensure the external terminal (SON) for servo enabling is set to OFF;
 Ensure the servo drive and the servo motor are grounded to the earth properly;
 When using external braking resistor, the short circuit wire between B2-B3 on X2
terminal should be removed;
 Do not put voltage above DC24V on CN1;
 The press threshold is among the designated range.。
2) Environment
 There are no foreign objections, such as metal and other wire lead which can
cause short circuit of signal and power wires.
3) Mechanical parts
 The installation of the servo drive and the connection of the bear are reliable;
 The servo motor and the machines are available to run;
 Do not run the motor at negative load (the direction of the output torque of the
motor reverses to the speed direction).
If all above items are checked OK, switch on the power supply:
5.1.1.1 Sequence of powering ON/OFF
The control circuit and the main circuit of the drive are supplied separately. In principle, when
powering on, switch on the power supply of the control circuit (terminals r, t) first and then
switch on the power supply of the main circuit (terminals R, S, T). When powering off, switch off
the power supply of the main circuit first and then switch off the power supply of the control
circuit.
After switching on the control circuit power supply and before switching on the main circuit
-44-
power supply, "AL-PoF” will display on the front panel as the main circuit power-off alarm. it
means the bus voltage of the main circuit is 0 or too low.
After switching on the power supply of the main circuit, do not
touch the motor line terminals even if the servo is not started as
this may cause electrical shock.
After switching on the power supply, do not touch the
electriferous parts as this may cause electric shock.
5.1.1.2 Checking after powering-on
After switching on both of the control circuit and main circuit power supplies, if the power supply
is OK, the Power indicator lamp on the front panel will illuminate in red and the servo drive and
servo motor will not generate abnormal noise. If there is no fault alarm of the servo drive, the
LED on the front panel displays the current speed of the servo motor as default. The default
parameter can be set through parameter FP0.15. The 3-color indicator lamp on the front panel
illuminates as blue. If there is a fault of the servo drive, the LED displays current alarm sign and
the 3-color indicator lamp on the front panel illuminates as red. Please fix the fault by referring
to chapter 9.1.
5.1.2 Self-test before running of the servo

The self-test before running the servo is very essential, it includes the following items:
1) Whether there are disconnecting of the motor encoder
Rotate the motor shaft with hands at least one cycle to see if it reports an encoder line break
fault (Er-EC1 or Er-EC2).
2) Whether there is abnormality of current detection
Verify whether the motor shaft is rotating while switching on the power, whether it reports a
current detection fault (Er-iTE) during power-on.
5.1.3 Parameter setting before running the servo

Parameter setting must be conducted before running the servo. You can set relevant
parameters via the front panel or communication to meet the function and performance
requirements of the site application. See chapter 5.2.4 for the detailed description of all
parameters of the servo drive. Some of these parameters need to be set according to the site
application demand. For examples, pulse input mode, electronic gear, frequency division
coefficient of encoder output, upper/lower limit of analog input, etc. Some of these parameters
need to be set according to the site debugging. For example, the parameters of the regulator
loop which affect the system performance and other similar parameters. For most parameters
the factory default values are appropriate.
-45-
5.1.3 Trial jogging
Trial jogging can check whether the servo drive and the servo motor are intact and conduct
preliminary debugging of the system including the servo drive, servo motor and peripheral
equipments. Run the servo motor by JOG operation after ensuring that the wiring is correct and
there is no fault alarm and no abnormal running, See chapter 5.2.4 for detailed instructions.
Before jog running, ensure:
 The motor isn’t in running state. If the motor is running, JOG operation is invalid;
 The load inertia shouldn’t exceed 15 times of the motor inertia. Otherwise it may
cause serious mechanical vibration;
 The jog speed can be set via parameterFP0.05.
 The accelerating/decelerating time during jogging can be set via parameters
FP0.54, FP0.55 and FP0.56, FP0.57.
5.1.4 Running at the position control mode

Simple connection:
Parameter Function Setting value

*FP0.03 Mode selection 0
*FP0.23 Pulse input Set according to the
requirement
*FP0.24 Pulse input direction reverse 0
FP0.25 The first electrical gear numerator 1
FP0.26 The first electrical gear 1
denominator
Figure 5-1 Simple connection of the position control mode
-46-
Steps:
1. Complete the connection between the drive and the servo motor.
2. Set FP0.03 to “0”, the position control mode.
3. Ensure the pulse output of the upper controller and adjust FP0.23. Keep the pulse type
is the same as that of the upper controller. Please refer to the instruction of FP0.23.
4. After modifying FP0.03 and FP0.23, it will be valid only when disconnecting the control
power and repower on.
5. Connect the corresponding terminal of CN1 and ensure the pulse wires (differential
output and open collector output)
6. Connect CN1 to the drive and apply the power supply. Control the connection between
SON and COM-. And then, the servo enters into the locking state.
7. Send the low frequency pulse command from the upper controller and rotate the motor
at low speed.
8. Ensure the rotating direction of the motor is as the designated. The direction can be
modified through the upper controller or operate on FP0.24.
9. Ensure the pulse number is as the designated. Please refer to the instruction of FP0.25
and FP0.26.
5.1.5 Running at the speed control mode

Simple connection
Parameter Function Setting value

FP0.40 Speed command selection 1
-47-
FP0.42 Speed command input gain 500

FP3.20 Bias voltage of analog input 1 Set according to
the requirement
Figure 5-2 Simple connection of the speed control mode
Steps:
2. Set FP0.03 to “1”, the speed control mode.
3. It is necessary to disconnect the control power supply after saving the modified value
of FP0.03. And it will be valid after repowering on.
4. Set FP0.40 to “1”, external analog speed command mode.
5. Set FP0.42 to the required value. Please refer to the instruction of FP0.42.
6. Connect the corresponding terminals of CN1.
7. Connect the CN1 to the drive and power on. Control the connection between SON and
COM-. Then the servo enters into the locking state.
8. The motor shaft may rotate at a low speed if there is no upper command voltage. It
needs to adjust FP3.20. Please refer to the detailed instruction of FP3.20.
5.1.6 Running at the torque control mode

Simple connection:
Parameters Function Setting value

-48-
FP0.60 Torque command selection 1

FP0.62 Torque command input gain 10
FP3.23 Bias voltage of analog input 2 Set according to the requirement
FP0.46 Speed limit 1 100
Figure 5-3 Simple connection of the pulse control mode

Steps:
2. Set FP0.03 to “2”, the torque control mode.
3. It is necessary to disconnect the control power supply after saving the modified
value of FP0.03. And it will be valid after repowering on.
4. Set FP0.04 to “1”, external analog torque command mode.
5. Set FP0.62 to the required value. Please refer to the instruction of FP0.62.
6. Connect the corresponding terminals of CN1.
7. Connect the CN1 to the drive and power on. Control the connection between SON
and COM-. Then the servo enters into the locking state.
8. The motor shaft may rotate at a low speed if there is no upper command voltage. It
needs to adjust FP3.23. Please refer to the detailed instruction of FP3.23.
9. In the torque mode, please adjust the speed limit and set FP0.46 to the required
value. Please refer to the detailed instruction of FP0.46.
5.1.7 Parameter setting before running the servo

Parameter setting must be conducted before running the servo. You can set relevant
parameters via the front panel or communication to meet the function and performance
requirements of the site application. See chapter 6 for the detailed description of all parameters
of the servo drive. Some of these parameters need to be set according to the site application
demand. For examples, pulse input mode, electronic gear, frequency division coefficient of
encoder output, upper/lower limit of analog input, etc. Some of these parameters need to be set
according to the site debugging. For example, the parameters of the regulator loop which affect
the system performance and other similar parameters. For most parameters the factory default
values are appropriate.
Hereunder only some necessary parameters are listed:
1) Mode setting
The control mode (position mode, speed mode, torque mode) can be set through setting
parameter FP0.03 according to the control requirements on the site. The mode will be valid
after repowering on.
-49-
2) Command input
Set or enter relevant commands to control the position, speed or torque of the servo motor’s
shaft according to the setting of parameter FP0.03.
 In the position mode: pulse command (3 kinds of input mode), internal torque limit
command or external analog torque limit command;
 In the speed mode: internal speed command or external analog speed command,
internal torque limit command or external analog torque limit command;
 In the torque mode: internal torque command or external analog torque command,
internal speed limit command or external analog speed limit command;
5.1.8 Servo enabling
Do not operate the switches with wet hand as this may cause
electric shock.
Please confirm the parameter setting before running. Otherwise

unexpected running state of the machinery may occur;
The radiator, regenerative braking resistor, servo motor and other
components may become very hot in a period after they are
powered on and powered off. Don’t touch them!
Enable the servo via the external servo enabling terminal (SON) or internal servo enabling
parameter (FP0.04). See the function description of terminal SON and detailed explanation of
parameter FP0.04 in chapter 4.5.2.4.
When servo enabling:
 If no alarm occurs, the state indicator of servo will turn to green;
 When the dynamic braking is triggering, light clatter can be heart;
 The fan starts to run;
 In the position mode, if there is no pulse command input, the servo is in locked
state;
 In the speed mode, the servo motor runs at the given speed;
 In the torque mode, if no torque is applied externally, the servo motor accelerates
from zero speed to the limit speed. If the external torque is larger than the internal
setting one, the servo motor maintains the state of zero speed output;
 If a servo alarm occurs, the servo status indicator will turn to red and the servo
motor will get into the inertia running state.
5.1.9 Coast to Stop / DEC to Stop of the servo

If the servo drive is in the following conditions, the servo motor will coast to a stop or stop
-50-
normally. Coasting to Stop means the drive cuts off output immediately, the motor coasts to rest
under the action of inertia, and does not keep in locked state after that. DEC to Stop means the
drive outputs reverse torque to make the motor to decelerate to zero speed and, after that, the
motor is in a locked state.
 When the servo enabling terminal (SON) signal is set to OFF, the servo motor will
stop. Select the stopping method through setting parameter FP4.30. See
description of FP4.30 for details. This process will not cause regenerative braking.
 When a fault alarm occurs, the servo motor will stop. Select the stopping method of
the servo motor when an alarm occurs through setting parameter FP4.30. See
description of FP4.30 for details. This process will not cause regenerative braking.
 When the zero speed clamp terminal (ZRS) signal is set to ON, the servo motor will
stop. In the position mode and torque mode, the servo motor will stop immediately.
In the speed mode, set parameter FP0.58 to select whether the servo motor stops
immediately or decelerates to stop according to the settings of parameter FP0.56
and FP0.57. After stop the servo is in a locked state. This stop process may cause
regenerative braking. If a braking overload fault alarm occurs, please install an
external braking resistor.
 If the travel limit terminal signal is valid (parameter FP3.40=1), and the travel limit
terminal (PSL/RVL) signal is set to OFF, the servo motor will immediately
decelerate to a stop and get into a locked state. After it stops running, if a reverse
running command is valid, the motor can run in reverse direction.
If the emergency stop terminal signal is valid (parameter FP3.41=1), and the emergency stop
terminal (EMG) signal is set to OFF, the servo motor will coast to stop.
-51-
5.1.10 Sequence diagram

5.1.10.1 Sequence diagram of power-on and servo ON
Fig. 5-4 Sequence diagram of Power-on and servo ON
-52-
5.1.10.2 Sequence diagram of power loss during running
Fig. 5-5 Sequence diagram of power loss during running
-53-
5.1.10.3 Servo OFF sequence in a locked state
Fig. 5-6 Servo OFF sequence diagram in a locked state
-54-
5.1.10.4 Servo OFF sequence in running state
Fig. 5-7 Servo OFF sequence diagram in running state
-55-
5.1.10.5 Sequence of fault alarm
Fig. 5-8 Sequence diagram of fault alarm
-56-
5.2 Display and operation

5.2.1 Display
Fig 5-8 Schematic diagram of the keypad

Table 5-1 State of the 3-color indicator
Color Function
Green Normal running state
Red Fault alarm state
Blue The control board is powering on but the servo is not started
Table 5-2 Key function definition
Key Key name Function
Used to switch between different modes or
MODE key
return to previous menu
Used to enter next menu or execute
SET key
setting command
Used to select parameter upwards or
UP key
increase value
Used to select parameter downwards or
DOWN key
decrease value
When setting a parameter, it is used to
SHIFT key
select the position of the current digit
There are 5 operation modes in total, which can be switched with key.
a) Status monitoring mode: used to display the values of the status parameters;
b) Basic parameter setting mode: used to set the basic parameters;
c) Gain and filtering parameter setting mode: used to set gain or filtering parameters;
d) Expansion parameter setting mode: used to set the expansion parameters;
e) Auxiliary function mode: used for JOG control and to restore parameters to default value.
Operation flowchart:
-57-
Fig.5-9 Flow chart of front panel operation
5.2.2 State monitoring mode

5.2.2.1 Operation flowchart
-58-
Fig.5-10 Flow chart of state monitoring operation

5.2.2.2 The meaning of state sign
The meanings are shown as below:
Table 5-3 Function meaning
Sign Name Unit Accuracy
r00.spd Motor speed r/min 0.1
r01.FP1 Lower 5 digits of feedback pulse accumulation pulse 1
r02.FP2 Medium 5 digits of feedback pulse accumulation pulse 1

r03.FP3 Higher 5 digits of feedback pulse accumulation pulse 1
r04.rp1 Lower 5 digits of command pulse accumulation pulse 1
r05.rp2 Medium 5 digits of command pulse accumulation pulse 1
r06.rp3 Higher 5 digits of command pulse accumulation pulse 1
r07.EP Detention pulse pluse 1
r08.An1 Analog speed command voltage V 0.01
r09.An2 Analog torque command voltage V 0.01
r10.ud1 Bus voltage of main circuit power V 0.1
r11.ud2 Bus voltage of control circuit power V 0.1
r12.cur RMS value of current output current A 0.01
r13.Tq Current torque % 1
r14.Tn Module temperature ℃ 0.1
r15.Ld Ratio of average load % 1
r16.PoS Position of the rotor relative to Z pulse pulse 1
r17.inE Ratio of load inertia time 1
r18.oAL Third latest fault alarm code - -
r19.AL Second latest fault alarm code - -
r20.ALc Latest fault alarm code - -
r21.in Digital input state - -
r22.ou Digital output state - -
r23.TT Motor temperature - -
r24.uE1 DSP software version - -

-59-
Sign Name Unit Accuracy

r25.uE2 FPGA software version - -
r26.uuu Encoder feedback value - -
r27.iA Instantaneous value of U phase output current A 0.01
r28.ib Instantaneous value of V phase output current A 0.01
Instantaneous value of U phase output current when A 0.01

r29.iAF
a fault occurs
Instantaneous value of phase V output current when A 0.01
r30.ibF
a fault occurs
r31.udF Bus voltage when a fault occurs V 0.1
r32.Sn1 Drive serial No. 1 - -

5.2.3 Parameter setting

5.2.3.1 Operation flowchart
-60-
Fig.5-11 Flow chart of parameter setting operation
5.2.3.2 Parameters list

P – position mode; S – speed mode; T – torque mode.
The function codes prefixed with sign “*” indicate the setting of these parameters can only take
effect after the system resets, restarts, or control circuit is powered off and repowered.
-61-
Function
Name Unit Range Default Mode
code
FP0 Basic control
FP0.00 Matching motor selection - 200~599 - PST
FP0.03* Mode selection - 0~6 0 PST
FP0.04 Internal servo enabling - 0~1 0 PST
FP0.05 Jog speed r/min 0.0~1000.0 200.0 PST
Numerator of the frequency
FP0.06* division coefficient of encoder - 0~30000 10000 PST
pulse output
Denominator of the frequency
FP0.07* division coefficient of encoder - 0~30000 0 PST
pulse output
FP0.11 Max torque limit % 0.0~300.0 300.0 PST
FP0.12 Internal torque limit % 0.0~300.0 - PS
Power of the external braking
FP0.13 W 0~1500 0 PST
resistor
Resistance of the external
FP0.14 Ω 1~100 1 PST
braking resistor
FP0.15* Default monitoring parameters - 0~37 0 PST
Parameter modification
FP0.16 - 0~1 0 PST
operation locking
Communication EEPROM write
FP0.17 - 0~1 0 PST
selection
FP0.23* Pulse input - 0~2 0 P
FP0.24* Pulse input direction reversing - 0~1 0 P
st
Numerator of the 1 electronic
FP0.25 - 1~65535 1 P
gear
st
Denominator of the 1
FP0.26 - 1~65535 1 P
electronic gear
nd
Numerator of the 2
FP0.27 - 1~65535 1 P
electronic gear
rd
FP0.28 - 1~65535 1 P
gear
th
FP0.29 - 1~65535 1 P
gear
nd
FP0.30 - 1~65535 1 P
electronic gear
rd
FP0.31 Denominator of the 3 - 1~65535 1 P
-62-
Function
code
electronic gear
th
FP0.32 - 1~65535 1 P
electronic gear
FP0.33 Position command filter time ms 0.0~1000.0 0.0 P
Speed command/speed limit
FP0.40 - 0~1 0 ST
selection
(r/min)/
FP0.42 Speed command input gain 10~1000 500 ST
v
FP0.44 Speed command filter time ms 0.0~1000.0 0.0 S
FP0.45 Dead zone of analog VA V 0.000~2.000 0.000 ST
-6000.0~600
FP0.46 Internal speed/speed limit 1 r/min 100.0 ST
0.0
-6000.0~600
0.0
-6000.0~600
0.0
-6000.0~600
0.0
FP0.54 ACC time ms 0~20000 0 S
FP0.55 DEC time ms 0~20000 0 S
FP0.56 S curve ACC time ms 0~1000 0 S
FP0.57 S curve DEC time ms 0~1000 0 S
FP0.58 Stopping method - 0~1 0 S
Torque command/torque limit
FP0.60 - 0~1 0 PST
selection
FP0.62 Torque command input gain %/V 10~300 10 PST
FP0.64 Torque command filter time ms 0.0~1000.0 0.0 T
FP0.65 Dead zone of analog TA V 0.000~2.000 0.000 PST
FP0.66 Internal torque command % -250.0~250.0 10.0 T
FP1 Self-turning control
FP1.02 Rotational inertia ratio % 0~10000 200 PST
FP1.03 Machine rigidity setting - 0~31 13 PST
FP1.04 Inertia identification switch - 0~1 0 P
FP1.05 Inertia identification operation - 0~3 0 P
FP1.06 Mechanical movement r 0.5~10.0 1.5 P
Identification of inertia
FP1.07 ms 2~200 2 P
acceleration time constan
FP1.20 Resonance frequency test valid - 0~1 0 PST
-63-
Function
code
st
1 mechanical resonance
FP1.21 Hz 0.0~3000.0 0.0 PST
frequency
nd
2 mechanical resonance
FP1.22 Hz 0.0~3000.0 0.0 PST
frequency
st
FP1.23 1 trap wave center frequency Hz 50.0~3000.0 3000.0 PST
st
FP1.24 1 trap wave width Hz 1.0~1000.0 50.0 PST
st
FP1.25 1 trap wave depth % 0.00~1.00 0.00 PST
nd
FP1.26 2 trap wave center frequency Hz 50.0~3000.0 3000.0 PST
nd
nd
FP2 Motor control
st
FP2.00 1 speed gain Hz 0.1~3000.0 27.0 PST
st
1 speed integration time
FP2.01 ms 0.1~1000.0 21.0 PST
constant
st
FP2.02 1 position gain 1/s 0.1~3000.0 48.0 P
st
FP2.03 1 speed detection filter time ms 0.00~100.00 0.00 PST
st
FP2.04 1 torque filter ms 0.00~25.00 0.84 PST
nd
nd
2 speed integration time
FP2.06 ms 0.1~1000.0 1000.0 PST
constant
nd
nd
FP2.08 2 speed detection filter time ms 0.00~100.00 0.05 PST
nd
FP2.10 Speed feed-forward % 0.0~100.0 30.0 P
FP2.11 Speed feed-forward filter time ms 0.00~60.00 0.50 P
FP2.12 Torque feed-forward gain % 0.0~100.0 0.0 PS
FP2.21 Gain switching selection - 0~1 1 PST
FP2.22 Gain switching condition - 0~5 0 PS
FP2.23 Gain switching time constant ms 0~100 0 PS
Pulse
0~5000/0~50
FP2.25 Gain switching threshold or 100/10.0 PS
0.0
r/min
FP2.47 Speed compensation threshold pulse 0~20000 100 P
FP2.48 Speed compensation r/min 0~500.0 0.0 P
FP3 I/O management
FP3.00 Digital 1 input - 0~11111 0 PST
FP3.20 Offset of AI VA V -2.000~2.000 0.000 ST
FP3.23 Offset of AI TA V -2.000~2.000 0.000 PST
-64-
Function
code
FP3.30 AO 1 selection - 0`7 0 PST
FP3.31 Voltage gain of analog output 1 - 0~1000 500 PST
FP3.32 AO 2 selection - 0~7 0 PST
FP3.33 Voltage gain of analog output 2 - 0~1000 500 PST
FP3.34 Offset of AO1 V -2.00~2.00 0.00 PST
FP3.35 Offset of AO 2 V -2.00~2.00 0.00 PST
FP3.40 Travel limit switch masking - 0~1 0 PST
FP3.41 E-stop masking - 0~1 0 PST
FP3.50 Range of position reaching pulse 0~20000 100 P
FP3.54 Range of speed reaching r/min 0.0~1000.0 30.0 S
FP3.55 Zero speed range r/min 0.0~1000.0 50.0 PST
Locked time of servo after
FP3.56 ms 100~5000 100 PST
braking
Braking delay time of the
FP3.57 ms 0~5000 1000 PST
electromagnetic brake
FP4 Extension and application
FP4.00* Communication mode - 0~1 1 PST
FP4.01 Local communication address - 0~31 1 PST
Communication baudrate
FP4.02* - 0~4 0 PST
selection
FP4.04 Communication parity mode - 0~17 0 PST
Communication response
FP4.05 ms 0~200 0 PST
delay time
Communication overtime fault
FP4.06 s 0.0~60.0 0.0 PST
time
Communication fault
FP4.07 - 0~1 0 PST
processing method
Communication response
FP4.08 - 0~1 1 PST
enabling
FP4.09 Reserved - - - PST
FP4.30 Stopping mode selection - 0~4 3 PST
FP4.31 Max. speed limit r/min 0~6500.0 - PST
FP4.32 Overspeed level r/min 0~6553.5 - PST
10puls
FP4.33 Pulse range for over position 0~50000 2000 P
e
Brake overload detection
FP4.34 - 0~1 1 PST
enabling signal
FP4.35 Input phase loss setting 0~1 0 PST
-65-
Function
code
FP9 Factory parameters
FP9.00 Factory password 100 PST
5.2.4 Auxiliary functions

There are two auxiliary functions: 1. Jogging trial function
2. Function of parameters restoration
These functions can be selected by pressing or .
5.2.4.1 Operation flowchart for jogging trial
Press MODE to select the auxiliary function Auxiliary function
Display EF-Jo- EF-Jo-

Press to select the required auxiliary functions
Press SET to enter the trial jogging SET MODE
The 3-color indicator of the servo drive is green and

the jogging speed will be displayed on the panel
0.0
Press and the servo drive is forward rotating
Press and the servo drive is reverse rotating
Press MODE to return

123.4 -123.4
The speed is set by FP0.05
Fig.5-12 Flow chart of jogging trial operation

5.2.4.2 Operation flowchart for function parameters resotration
-66-
Fig.5-10 Flow chart of default parameter function restoration operation
5.2.5 Alarm display

When the servo drive runs abnormally, it will perform fault alarm or warning protection. At this
time the panel will display the fault alarm or warning identifier.
The meanings of the alarm or warning identifiers are listed in the table below:
Table 5-4 Comparison table of faults or warning identifier
Sign Name
EEPROM fault
Encoder line break fault 1
Encoder line break fault 2
Current test fault
Hardware overcurrent fault
Line-to-ground short circuit fault
Brake overload fault
Overvoltage fault
Undervoltage fault
Overload fault
Ground abnormality fault
Overspeed fault
-67-
Sign Name
Drive overtemperature fault
Software overcurrent fault
Over-pulse fault
Communication fault
Write/read overtime fault
Brake overload fault
IPM module fault
The power input phase loss fault
er-inE Inertia identification fault
Er-DrE Motor parameters matching fault
Forward travel limit warning
Reverse travel limit warning
Emergency stop warning
Main circuit power-down warning
Communication abnormality warning
5.2.6 Alarm clearance

For fault alarms, if the fault condition is removed, the fault alarm display can be removed by
short connecting the alarm clear terminal CLA with COM-. If the servo is still in enabled state at
this time, the drive will recover running automatically. Please note that when EC2 fault or OC2
fault is reported, even if the fault is removed, it can be cleared only after the control circuit is
powered off and re-on. For warnings, if it is the travel limit warning, once the warning condition
is removed, the drive will clear the warning display automatically. If the servo is still in enabled
state at this time, the drive will recover running automatically. If it is the emergency stop
warning, if the warning condition is removed, the warning display can be removed by short
connecting the alarm clear terminal CLA with COM-. But the servo must be enabled again to
allow the drive to continue running.
If parameters need to be set when a fault alarm or warning occurs but they are not removed,
press and hold for about 3 seconds while the panel displays the fault alarm or warning
identifier to enter the parameter setting mode. After the parameters are set, press and hold
down for about 3 seconds to exit the parameter setting mode and the panel recovers
displaying of the fault alarm or warning identifier.
-68-
Operational manual for INVT SV-DB100 AC Servo drives Detailed parameter description
6 Detailed parameter description

Sign description: P – position mode; S – speed mode; T – torque mode.
The setting of the parameters marked with * can only take effect when the control circuit is
powered-off and repower-on.
6.1 Basic parameters (FP0 group parameters)

6.1.1 Basic control
Setting Available
Matching motor Default Unit
FP0.00 range mode
selection
200~500 - - P S T
Detailed instruction: Right motor parameters are set
in factory. Refer to the name plate. For example, the
name plate of 400W motor is :
of which, No.: 2300 is the set value of the parameter.
Note: Wrong setting may cause abnormal running or
damage to the drive and motor.
Setting Available
Default Unit
*FP0.03 Mode selection range mode
0~6 0 - P S T
Detailed instruction:
This parameter can be used to set the operating mode of the system:
st nd
Setting 1 working 2 working
Instruction
value mode mode
Position mode: In the position mode, it can
control the angular displacement of the
servo motor with the pulse command and
0 P /
thus achieve the goal to control the
displacement of the mechanical
movement.
Speed mode: The mode can control the
rotation speed of the servo motor with the
1 S /
internal speed command or external
analog speed command
Torque mode: The mode can control the
2 T /
output torque of the servo motor with the
-69-
internal torque command or external

analog torque command.
Position/speed mode: The position mode
and speed mode can be switched with the
control mode switching terminal (MCH pin
“1”).
3 P S
Note: For safety, after changing the MCH

terminal input status, the switching
between position mode and speed mode
can be performed only when the motor
speed becomes lower than the value of
zero speed range (FP3.55).
Speed/torque mode: The speed mode and
torque mode can be switched with control
mode switching terminal (MCH pin “1”).
4 S T
Note: The mode can not be limited by the

current working condition.
-70-
Position/torque mode: The position mode

and torque mode can be switched with the
control mode switching terminal (MCH pin
“1”).
5 P T
Note: For safety, after changing the MCH

terminal input status, the switching
between position mode and torque mode
can be performed only when the motor
speed becomes lower than the value of
zero speed range (FP3.55).
Factory reserved mode. Setting by the
6 Reserved Reserved
user is prohibited.
Remarks:
MCH terminal state Current working mode
st
0 1 working mode
nd
1 2 working mode
Note: MCH is the connecting terminal of CN1. The corresponding relationships
between pin “1” and COM-:
0：OFF (the terminal is disconnected with COM-);
1：ON (the terminal is connected with COM-).
Setting Available
Internal enabling Default Unit
FP0.04 range mode
command
0~1 0 - P S T
Control the running state through modifying the parameters:
Setting value of External terminal Working state of the
FP0.04 command state servo drive
0 0(the terminal is Stand-by (OFF)
-71-
disconnected with COM-)

1(the terminal is Enabling running
0
connected with COM-) (ON)
1
disconnected with COM-) (ON)
1
connected with COM-) (ON)
Note: For safety, this parameter will automatically become 0 when fault alarm occurs
and after the control circuit is powered on and the system is reset. If you want to run
the servo drive, this parameter must be reset.
Warning: If the servo drive is controlled by the external, please ensure there is no
system fault and disconnect the terminal with COM-.
Setting Available
Default Unit
FP0.05 Jog speed (JOG) range mode
0~1000.0 200.0 r/min P S T
This parameter can be used to set the jog speed. For jogging, please refer to chapter
5.1.3. During jogging, the ACC/DEC time parameters (FP0.54, FP0.56, FP0.55,
FP0.57) are active. The motor will accelerate, decelerate, start and stop according to
the settings.
Numerator of the Setting Available

Default Unit
frequency division range mode
*FP0.06
coefficient of encoder
0~10000 1 1 P S T
pulse output
Denominator of the Setting Available
Default Unit
frequency division range mode
*FP0.07
0~10000 1 1 P S T
pulse output
By setting the numerator and denominator of the frequency division coefficient of
encoder pulse output, the phase A and phase B signals of the encoder can be
frequency divided by any integer or decimal fraction and then outputted through the
encoder’s pulse output signal terminals(OA+, OA-, OB+ and OB- pin 44, 43, 41 and
42) FP0.06
Output pulse number of the drive = ×Resolution of the encoder

-72-
FP0.07
Note: In the position control mode, if the encoder output signal of the preceding stage
servo motor is used as the position pulse command input of the succeeding stage
servo drive, i.e. as start/stop type master-slave follow-up, in order to ensure high
positioning accuracy of the succeeding stage servo drive, the frequency division
coefficient must be 1:1. Otherwise the accuracy of master-slave position follow-up will
be affected in this case.
Setting Available
Default Unit
FP0.11 Max torque limit range mode
0~300 300 % P S T
This parameter can be used to set the maximum torque of the servo motor can
output. Taking the rated torque of the servo motor as 100%, the setting is the
percentage of the rated torque of the servo motor. If the absolute value of the torque
command is larger than the value of this parameter, then the actual output torque will
be limited by the parameter.
Setting Available
Default Unit
FP0.12 Internal torque limit range mode
0~300.0 250.0 % P S
In the speed and position modes, this parameter is used to set the value of internal
torque limit. Taking the rated torque of the servo motor as 100%, this setting is the
percentage of the rated torque of the servo motor.
Setting value
Control mode TQC Torque limit state
of FP0.04
Setting value of FP0.12
0
Position mode 0 internal torque limit
or speed mode 1 External analog torque limit
1 Invalid External analog torque limit
Note:
1. Below is the relationship between TQC and COM-:
0:OFF (the terminal is disconnected with COM-);
1: ON (the terminal is connected with COM-).
2. The default value and setting range of the parameter are relative to the power
grade of the drive. The default value of drives below 2.0kW (icluding 2.0kW) 2.0kW is
0~300.0 and the default value of drives above (including) 2.0kW is 0~250.0.
-73-
Resistance of the Setting Available

Default Unit
FP0.14 external braking range mode
resistor 1~100 1 Ω P S T
Setting Available
Power of the external Default Unit
FP0.13 range mode
braking resistor
0~1500 0 W P S T
When an external braking resistor is connected, this group of parameters should be
set with the values equal to the resistance and power of the external braking resistor.
Please set this group of parameters correctly. Otherwise if the values of this group of
parameters are not matched with the parameters of the external braking resistor, it
may report a braking overload fault (Er-bCE) by mistake or cause burnout of the
braking resistor. The regenerative braking overload protection time is proportional to
these two parameters. When FP0.13=0, the internal braking resistor is active.
Setting Available
Default monitored Default Unit
*FP0.15 range mode
parameters
0~26 0 - P S T
This parameter is used to set the parameters which can be monitored while
powering-on of the system:
Setting Parameter meaning Accuracy Unit
value
00 Current motor rotation speed 0.1 r/min
Lower 5 digits of feedback
01 1 pulse
pulse accumulation
Medium 5 digits of feedback
02 1 pulse
pulse accumulation
Higher 5 digits of feedback
03 1 pulse
pulse accumulation
Lower 5 digits of command
04 1 pulse
pulse accumulation
Medium 5 digits of command
05 1 pulse
pulse accumulation
Higher 5 digits of command
06 1 pulse
pulse accumulation
-74-
07 Retention pulse 1 pulse

Analog speed command
08 0.01 V
voltage
Analog torque command
09 0.01 V
voltage
Setting Parameter meaning Accuracy Unit
value
Main circuit power bus
10 0.1 V
voltage
Control circuit power bus
11 0.1 V
voltage
Effective value of current
12 0.01 A
output current
13 Current torque 1 %
14 Drive module temperature 0.1 ℃
15 Average load rate 1 %
Position of the rotor relative
16 1 pulse
to Z pulse
17 Inertia ratio of load 1 time
The two previous fault alarm
18 / /
code
The previous fault alarm
19 / /
code
20 Current fault alarm code / /
21 Digital input state / /
22 Digital output state / /
23 Motor temperature 0.1 ℃
24 DPS software version / /
25 FPGA software version / /
Encoder UVW feedback
26 / /
value
Instantaneous value of phase
27 0.01 A
U output current
28 0.01 A
V output current
-75-
Instantaneous value of U
29 phase output current when a 0.01 A
fault occurs
30 V output current when a fault 0.01 A
occurs
Bus voltage when a fault

31 0.1 V
occurs
32 Drive serial No. 1 / /
Parameter Setting Available

Default Unit
FP0.16 modification operation range mode
locking 0~1 0 - P S T
This parameter is used to mask the parameter setting function and thus to avoid
incorrect modification of the parameters by the user：
Setting
Operation Communication operation
value
Parameter modification Parameter modification
0
valid valid
Parameter modification Parameter modification
1
invalid valid
6.1.2 Position control

Setting Available
Default Unit
*FP0.23 Pulse input form range mode
0~2 0 - P - -
This parameter is used to set the manner of pulse input. There are 3 types of pulse
input manners:
Pulse input Signal Shown in the picture
FP0.23
form form FWD(CW) REV(CCW)
-76-
Pulse + pulse
0
sign sign
FWD/REV pulse
1
pulse train sign
Orthogonal
pulse
2 encoder
sign
pulse
Remark: The pulse direction of the parameter can be reversed by FP0.24. Please
refer to FP0.24 for detailed information.
Setting Available
Pulse input direction Default Unit
*FP0.24 range mode
reversing
0~1 0 - P - -
By setting this parameter, the direction of the input pulse can be reversed. At this time
the actual output speed direction of the servo drive is opposite to the direction
indicated by the pulse input form in FP0.23.
0: Pulse input direction does not change;
1: Pulse input direction is opposite to the original input direction.
Setting Available
Numerator of the Default Unit
FP0.25 st range mode
1 electronic gear
1~65535 1 - P - -
Denominator of Setting Available
st Default Unit
FP0.26 the 1 electronic range mode
gear 1~65535 1 - P - -
nd Default Unit
FP0.27 2 electronic range mode
gear 1~65535 1 - P - -
rd Default Unit
gear 1~65535 1 - P - -
th Default Unit
gear 1~65535 1 - P - -
-77-

nd Default Unit
gear 1~65535 1 - P - -
rd Default Unit
gear 1~65535 1 - P - -
th Default Unit
gear 1~65535 1 - P - -
Concept of the electronic gears: for discretional pulse input, the number and frequency of
the pulse actually received by the drive can be changed by multiplying a certain
coefficient. It can be shown separately with two parts: numerator and denominator:
g1
g 2
Electronic gear = ;
Of which
g1 :The numerator of the electronic gear;
g 2 : The denominator of the electronic gear;
Below is the schematic diagram of the electronic gear in the system:
Example:
Below is a case where 1 pulse is equivalent to a feed
rate of 10
m
Mechanical specifications:
Feed of the ball screw Pb =10mm;
Reduction ratio n =3/5;
Resolution of the servo motor encoder =10000;
At this time calculate the electronic gear:
g1 Pt Pt 10000 50
 l 0   l 0   10 103  
g2 S n  Pb (3 5) 10 3
In the formula :
-78-
l 0
:Feed rate corresponding to per pulse (mm/pulse);
S ：Feed rate corresponding to per revolution of the motor (mm/rev).
I.e. in this example, g1 =50, g 2 =3.
Set FP0.25 to 50 and FP0.26 to 3.
The servo drive supplied 4 groups of electronic gear: FP0.25, FP0.26, FP0.27, FP0.30,
FP0.28, FP0.31, FP0.29 and FP0.32. Select the terminal by the electronic gear of CN1
(Pin 34 of SC1 and Pin 17 of SC2) to determine the parameter. The corresponding
relationships are listed in the table below:
SC1 SC2 Position mode
0 0 Electronic gear 1
Note: SC1 and SC2 are the wiring terminals of CN1. The relationship between COM- and
Pin 34 and 17:
0：OFF (the terminal is disconnected with COM-);
1：ON (the terminal is connected with COM-).
Setting Available
Position command Default Unit
FP0.33 range mode
filter time
0~6000 0 512μs P - -
st
This parameter is used to set the time constant of the 1 order low-pass filter
corresponding to the position command. By setting this parameter, mechanical shock
can be reduced in cases when the input pulse command frequency changes abruptly.
See the figure below:
6.1.3 Speed and torque control

Speed command Setting Available
Default Unit
FP0.40 selection/speed limit range mode
selection 0~1 0 - - S T
-79-
Setting
Control Function value Input
Instruction
mode name of method
FP0.40
Select the internal multi-stage speed by the
speed selection terminal of CN1(Pin 34 and
17 of SC1 and SC2 )
Parameter Speed
SC2 SC1
mode
FP0.46 Internal
Internal 0 0
speed 1
speed
0 FP0.47 Internal
command 0 1
speed 2
manner
FP0.48 Internal
1 0
speed 3
FP0.49 Internal
Speed 1 1
Speed speed 4
command
mode Please refer to the detailed instruction of
selection
FP0.46, FP0.47, FP0.48 and FP0.49.
The speed of the servo motor can be
controlled by applying a voltage between
-10V and 10V on the analog speed input
External terminals (VA+, VA- and pin 20 and 5).
analog According to the factory default, positive
1 speed value means forward direction and negative
command value means reverse direction. But it can be
manner changed by setting parameters
Pc.28~Pc.31.
Please refer to the detailed instruction of
Pc.28~Pc.31.
Speed
Torque
limit
mode 0 Internal Select the internal multi-stage speed limit by
selection
speed the speed selection terminal of CN1 (SC1,
limit SC2 and pin 34 and 17).
Parameter Speed
SC2
-80- SC1
mode
0 0 FP0.46 Speed
limit 1
FP0.47 Speed
0 1
limit 2
FP0.48 Speed
1 0
limit 3
FP0.49 Speed
1 1
limit 4
Please refer to the detailed instruction of
FP0.46, FP0.47, FP0.48 and FP0.49.
Note: The speed limit depends on the
absolute value of the corresponding
parameter. The direction is the same as that
of the torque command.
The motor speed can be limited by applying
a voltage between -10V and 10V on the
analog speed limit terminals (VA+, VA- and
pin 20 and 5). The magnitude of the speed
External
limit value is the absolute value of the
analog
analog input, the direction of it is the same
1 speed
as that of the torque command. The speed
limit
limit can be modified.
manner
Note: The speed limit depends on the
absolute value of the corresponding
parameter. The direction is the same as that
of the torque command.
Note: Please note that in the torque mode; do not allow the motor to run under the
condition of negative load.
Setting Available
Speed command Default Unit
FP0.42 range mode
input gain
10~1000 500 (r/min)/v -
1. The voltage of set analog inputVA corresponds to the switching gain of command
speed.
2.The relationship between analog VA input coltage and speed is default as each 1V:
500r/min。
FP0.40 Speed command/speed limit
0 FP0.46, FP0.47, FP0.48, FP0.49
-81-
1 Input voltage x FP0.42

Speed r/min
5000
FP0. 42=500(r/min)/v
2500
FP0. 42 =250 (r/min)/v
-10.0V
10.0V Input voltage of
analog 1
-2500
-5000
Note：
1. Analog input VA is the input signal from analog speed/speed limit terminal.
2. The parameter is valid when FP0.40 is set to “1”.
3. Set right parameter after ensure the running. Big setting value may cause big
fluctuation of motor speed.
4. Large voltage between VA+ and VA- may cause damage to the drive. (-10~10V)
Setting Available
Speed command filter Default Unit
FP0.44 range mode
time
0~6000 0 256μs - S -
st
corresponding to the analog speed command. By setting this parameter, the change
of the speed will be more gently in cases the speed analog input changes largely. See
the figure below:
Setting Available
Dead zone of Default Unit
FP0.45 range mode
analog VA
0.000~2.000 0.000 V - S T
Internal Available
Setting range Default Unit
FP0.46 speed/speed limit mode
1 -6000.0~6000.0 100.0 r/min - S T
-82-
Internal Available
2 -6000.0~6000.0 100.0 r/min - S T
The servo drive provides 4 stages of internal speed command/internal speed limit:
Control Setting value Relative parameters and
SC1 SC2
mode of FP0.40 setting
0 0
Internal speed 1
1 0
Speed Internal speed 2
0
mode Setting value of FP0.48
0 1
Internal speed 3
1 1
Internal speed 4
0 0
internal speed limit 1
1 0
Torque internal speed limit 2
0
mode Setting value of FP0.48
0 1
1 1
Note:
1. SC1 and SC2 are the wiring terminals for CN1. The corresponding relationships
are listed in the table below:
0: OFF (the terminal is disconnected with COM-);
2. The speed limit depends on the absolute value of the corresponding parameter.
The directions the same as that of the torque command.
3. The setting range of the parameter is subject to the power grade of the drive. The
setting range of drives below (including) 2.0kW is -5000.0~5000.0, and above
(including) 2.0kW is -3000.0~3000.0.
Internal Available
3 -6000.0~6000.0 100.0 r/min - S T
-83-
Internal Available
3 -6000.0~6000.0 100.0 r/min - S T
The function of the parameters is the same as that of FP0.46 and FP0.47.
Setting Available
Default Unit
FP0.54 ACC time range mode
0~20000 0 ms - S -
Setting Available
Default Unit
FP0.55 DEC time range mode
0~20000 0 ms - S -
ACC/DEC time means that in the case of internal reference speed command, the time
required for the speed setting to increase from 0r/min to 3000r/min. When the speed
setting is quicker or slower than 3000r/min, the actual ACC/DEC time is calculated at
the proportion. If the speed command is a negative value, the ACC/DEC time is
calculated with its absolute value.
For example, assuming that the reference speed is 2000r/min and the ACC/DEC time
(FP0.54 and FP0.55) is set as 1500 and 1500, at this time the actual ACC time of the
speed command is 1500×(2000/3000)=1000(ms) and the DEC time is
1500×(2000/3000)=1000ms.
The meaning of the ACC/DEC time is shown in the figure as below:
Note:
1. ACC/DEC time can only be used in the speed mode, and it is only valid when
FP0.40 is set to 0.
2. ACC/DEC time is valid when using jogging function.
FP0.56 S curve ACC time

Setting Default Unit Available
-84-
range mode
0~1000 0 ms - S -
Setting Available
Default Unit
FP0.57 S curve DEC time range mode
0~1000 0 ms - S -
In a case of internal reference speed command, this parameter is used to set the
duration of the circular arc segment during S curve decelerating and thus to achieve
the goal of smoothly stopping. The ACC/DEC time of S curve is shown in the figure
below:
Note:
1. The ACC/DEC time of S curve can only be used in the speed mode and it is valid
when FP0.40 is set to 0.
2. The ACC/DEC time of S curve is valid when using jogging function.
Setting Available
Default Unit
FP0.58 Stopping method range mode
0~1 0 - - S -
This parameter is used to set how the servo motor stops running when the zero speed
clamp terminal (ZRS pin37) signal is set to ON in the speed mode:
0: Decelerate to stop. The DEC time is the setting values of parameter FP0.56and
FP0.57;
1: Instant stop. The DEC time is 0.
Torque Setting Available

Default Unit
FP0.60 command/torque limit range mode
selection 0~1 0 - P S T
-85-
Setting
Control Function value Input
Instruction
mode name of method
FP0.04
Set the required torque by setting
Internal
FP0.66.
0 torque
Please refer to the detailed
command
instruction of PA. 11.
The output torque can be controlled
by applying a voltage between -10V
Torque Torque and 10V on the analog torque input
mode command External terminals (TA+, TA- and pin 7 and 8).
analog By factory default, the positive value
1
torque means forward and negative value
command means reverse. But it can be
changed by setting parameters.
instruction.
The output torque can be limited by
setting the internal torque limit
parameter (FP0.12) or the internal
and external torque limit can be
Internal
switched by changing the state of
0 torque
TQC and COM-. The direction of the
limit
torque limit is the same as that of the
speed command.
Speed
mode Torque
instruction.
or limit
The output torque can be limited by
position selection
applying a voltage between -10V and
mode
10V on the analog torque limit
External terminals (TA+, TA- and pin 7 and 8).
analog The magnitude of the torque limit is
1
torque the absolute value of the analog
limit input, the direction of it is the same
as that of the torque command. But it
can be changed by setting
parameters.
-86-

instruction.
Note: Please note that in the torque mode; do not allow the motor to run under the
condition of negative load.
Torque Setting
Default Unit Available mode
FP0.62 command range
input gain 10~300 10 %/v P S T
1. The voltage of set analog input TA corresponds to the switching gain of torque
command.
2. The parameter is valid when FP0.60 is set to “1”.
3. The relationship between analog TA input coltage and speed is default as each
1V: 10% of the rated torque
Running mode FP0.60 Torque command/torque limit
Position/speed 0 FP0.12
mode 1 Input voltage X FP0.62
Torque mode 0 FP0.66
1 Input voltage X FP0.62
Rated torque %
100
FP0.62=10%/ v
50
FP.062=5%/v
-10.0V
10.0V Input voltage of
analog 2
-50
-100
Note：
1. Analog input TA is the input signal from analog speed/speed limit terminal.
2. Set right parameter after ensure the running. Big setting value may cause big
fluctuation of motor speed.
Setting Available
Torque command Default Unit
FP0.64 range mode
filter time
0~6000 0 256μs - - T
-87-
st
corresponding to the torque command. By setting this parameter, the actual output
torque changes more gently in cases the torque command changes largely. See the
figure below:
Setting Available
Dead zone of Default Unit
FP0.65 range mode
analog TA
0.000~2.000 0.000 V P S T
Available
Internal torque Setting range Default Unit
FP0.66 mode
command
-250.0~250.0 10.0 % - - T
This parameter is used to set the internal torque setting. Taking the rated torque of the
servo motor as 100%, this setting is the percentage of the rated torque of the servo
motor.
Note:
1. If the absolute value of this parameter is larger than FP0.11, then the output torque
is the value of FP0.11 and the direction is the same as that of the parameter.
2. In the torque mode, the parameter is valid if FP0.04 is set to 0.
6.2 Self-turning control parameters (FP1 group parameters)

6.2.1 Inertia identification(Automatic gain)
Setting Available
Default Unit
FP1.02 Rotational inertia ratio range mode
0~30 0 - P S T
This parameter is used to set the ratio of the load inertia converted into the rotor shaft
to the inertia of the servo motor.
Load rotational inertia on the rotor shaft (JL)
Setting value of FP1.02 =
Rational inertia of the rotator of the servo drive(JM)：
-88-
Setting Available
Machine rigidity Default Unit
FP1.03 range mode
setting
0~31 13 -- P S T
The bigger the value is, the faster response and higer rigidty and easier vibration. In
stable system, higer rigidity setting makes fast response.
Mechanical structure Rigid set
Big handling, transmission 0~13
equipment
Belt drive mechanism 5~16
Manipulator 10~20
Ball screw + Belt drive 13~25
Direct ball screw or rigid 18~31
bodies
Setting Available
Inertia identification Default Unit
FP1.04 range mode
switch
0~1 0 -- P
0: Inertia identification switch off
1: Inertia identification switch on
Note:
1. The parameter is valid in position mode;
2. The bigger value of FP1.06 and FP1.07, the faster the motor speed;
3. Refer to chapter 9.1 if the drive report Er-INE.
Setting Available
Inertia identification Default Unit
FP1.05 range mode
operation
0~3 0 -- P
In position mode, if FP1.04=1, the motor will:
0: Forward rotate and then reverse rotate
1: Forward rotate
2: Reverse rotate
3: Reverse rotate and thenforward rotate
-89-
Setting Available
Mechanical Default Unit
FP1.06 range mode
movement
0.5~10 1.5 r P
In position mode,if the inertia identification is valid, the parameter can limit the
maximum running revolutions in each cycle.
Identification of inertia Setting Available

Default Unit
FP1.07 acceleration time range mode
constant 2~200 2 ms P
The setting of this parameter is the command of ACC time constant of the motor,
other than the actual ACC time. the bigger the value, the longer the ACC time. if the
load inertia is big enough, ACC time can be set as a long time to ensure the speed of
the motor exceeds 150r/min.
6.2.2 Adaptive vibration control

Setting Available
Resonance frequency Default Unit
FP1.20 range mode
test valid
0~1 0 - P S T
This parameter is used to set whether the resonance frequency is valid or not. If it is
valid, the system will analysis the automatically-collected data and save the result to
FP1.21 and FP1.22. The user can set the frequency of the notch filter according to
the value of FP1.21 and FP1.22 to remove the resonance.
0: Resonance frequency test invalid
1: Resonance frequency test valid
st
1 mechanical Setting Available
Default Unit
FP1.21 resonance frequency range mode
0~1500 0 Hz P S T
nd Setting Available
2 mechanical Default Unit
FP1.22 range mode
resonance frequency
0~1500 0 Hz P S T
This parameter is used to display the resonance frequency. When FP1.20 is set to 1,
the system will detect the frequency on the Max. resonance and display it by the
function codes.
-90-
Note:
1. When the speed reaches above 30r/min, the measuring value will be correct.
2. This function is only for read and can not be set. The user can set the frequency of
the notch filter according to the function code to remove the resonance.
st Setting Available
1 trap wave center Default Unit
FP1.23 range mode
frequency
50~2000 2000 Hz P S T
st
This parameter is used to set the frequency of the 1 trap wave filter for suppressing
resonance. The trap wave filters can simulate the mechanical resonant frequency and
thus suppress the resonant frequency.
50~1999: trap wave frequency;
2000: invalid.
Setting Available
st Default Unit
FP1.24 1 trap wave width range mode
1.0~1000.0 50.0 Hz P S T
st
This parameter is used to set the trap wave width of the 1 trap wave filter for
suppressing resonant. A larger trap wave width can be obtained with a larger setting.
Setting Available
st Default Unit
FP1.25 1 trap wave depth range mode
0.00~1.00 0.00 % P S T
st
This parameter is used to set the trap wave depth of the 1 trap wave filter for
suppressing resonant. A larger trap wave depth can be less with a larger setting.
2 trap wave center Default Unit
FP1.26 range mode
frequency
50.0~3000.0 3000.0 Hz P S T
Setting Available
nd Default Unit
FP1.27 2 trap wave width range mode
1.0~1000.0 50.0 Hz P S T
FP1.28 2 trap wave depth Default Unit
range mode
-91-
0.00~1.00 0.00 % P S T
Please refer to FP1.23, FP1.24 and FP1.25.
st nd
Using the 1 and 2 notch filters at the same time can suppress 2 mechanical
resonant.
6.3 Motor control parameters (FP2 group parameters)

6.3.1 Gain
Setting Available
st Default Unit
FP2.00 1 speed gain range mode
1~30000 1000 rad/s P S -
This parameter is used to set the gain of the speed loop. When the setting is
increased, the speed response will be improved, but it may easily cause vibration and
noise.
1 speed integration Default Unit
FP2.01 range mode
time constant
1~5000 100 256μs P S -
This parameter is used to set the integration time constant of the speed loop. The
response may be improved by decreasing the setting, but this parameter may easily
cause vibration and noise. It should be noted particularly that when this parameter is
set as 5000, it means the integral action is invalid.
Setting Available
st Default Unit
FP2.02 1 position gain range mode
0.1~3000 48.0 1/s P - -
This parameter is used to set the gain of the position loop. When the setting is
increased, the position response will be improved, but it may easily cause vibration
and noise.
1 speed detection Default Unit
FP2.03 range mode
filter time
0.00~100.00 0.00 ms P S T
-92-
This parameter is used to set the time constant of the speed detect filter.
Setting Available
st Default Unit
FP2.04 1 torque filter range mode
0.00~25.00 0.84 ms P S T
This parameter is used to set the time constant of torque filter. Refer to 7.1.2.
Setting Available
nd Default Unit
FP2.07 2 position gain range mode
0.1~3000.0 57.0 1/s P - -
Setting Available
nd Default Unit
FP2.05 2 speed gain range mode
0.1~3000.0 27.0 Hz P S T
nd
2 speed Setting Available
Default Unit
FP2.06 integration time range mode
constant 0.1~1000.0 1000.0 ms P S T
2 speed detection Default Unit
FP2.08 range mode
filter time
0.00~100.00 0.05 ms P S T
Setting Available
nd Default Unit
FP2.09 2 torque filter range mode
0.00~25.00 0.84 ms P S T
There are two groups of parameters for position gain, speed gain and speed
integration time constant.
st
The definition of the function and content are the same as those of 1 group.
st nd
The user can select or switch between 1 gain and 2 gain according to the
requirement. Please refer to the detailed information of FP2.21 and FP2.22.
Setting Available
Speed feed-forward Default Unit
FP2.10 range mode
gain
0.0~100.0 30.0 % P - -
This parameter is used to set the speed feed-forward gain.
FP2.11 Speed feed-forward

-93-
range mode
filter time constant
0.00~60.00 0.50 ms P - -
This parameter is used to set the speed feed-forward filter time constant.
Setting Available
Torque feed-forward Default Unit
FP2.12 range mode
gain
0.0~100.0 0.0 % P S -
This parameter is used to set the torque feed-forward gain.
6.3.2 Gain switching

Setting Available
Gain switching Default Unit
FP2.21 range mode
selection
0~1 0 - P S T
Setting Available
Gain switching Default Unit
FP2.22 range mode
condition
0~5 0 - P S -
Setting
value
Function
of
FP2.22
When FP2.22 is set to 0, FP2.21 can set to gain
switching selection. Carry out manual gain switching
according to the relationship between the gain switching
terminal and COM-.
Setting
Function
value of PLC Content
name
Manual FP2.21
0 gain Speed loop adjustor
Speed loop 0
switching ——PI adjustment
0 gain
Speed loop adjustor
switching 1
——P adjustment
st
Switching 0 1 gain
st
1 from 1 gain nd
nd 1 2 gain
to 2 gain
Note:
-94-
PLC is the wiring terminal of CN1 (pin 36). Below is its

relationship with COM-:
0: OFF(the terminal is disconnected with COM-);
nd
1 Fix to the 2 gain
nd
When the retention pulse is too large, select the 2 gain, otherwise
st
2 select the 1 gain and the threshold of the retention pulse is set with
FP2.25
nd
When the speed command is too large, select the 2 gain, otherwise
st
3 select the 1 gain and the threshold of the speed command is set
with FP2.25
nd
When the speed command is relatively small, select the 2 gain,
st
4 otherwise select the 1 gain and the threshold of the speed
command is set with FP2.25
Position command + speed gain switching mode. In the position
mode, when no position command pulse is inputted, it will select the
st
1 gain. When a position command pulse is inputted, it will select the
5 nd
2 gain. After the position command pulse stops input for 3ms and
the motor speed falls below the speed threshold set with FP2.25, it
st
will switch to the 1 gain.
Setting Available
Gain switching time Default Unit
FP2.23 range mode
constant
0~1000 0 ms P S T
Detailed instruction:：
This parameter is used to set the time constant of the transition process when
st nd
switching between the 1 gain and 2 gain. This parameter is active only for the
proportional parameters. By setting this parameter we can lighten the mechanical
shock caused by gain switching. See chapter 7.3 for details.
Setting Available
Default Unit
Gain switching range mode
FP2.25
threshold 0~6000 0 256μs
P S -
0~500.0 10.0 r/min
The setting content of this parameter is relative to the setting value of FP2.22:
Setting value of The setting content of FP2.25 during
-95-
FP2.22 gain switching

2 Retention pulse threshold
3
4 Speed threshold
5
6.3.3 Special motor control

Setting Available
Speed compensation Default Unit
FP2.47 range mode
threshold
0~20000 100 pulse P - -
Setting Available
Default Unit
FP2.48 Speed compensation range mode
0.0~500.0 0.0 r/min P - -
FP2.47 is used to set the retention pulse threshold of the speed compensation on the
position mode.
In the position mode, if the absolute value of the retention pulse is above the setting
value of FP2.47. And FP2.48 can be added on the speed command to decrease the
time of position reaching. The function is shown as below:
6.4 I/O management parameters (FP3 group parameters)

6.4.1Digital input
Setting Available
Polarity reversing Default Unit
FP3.00 range mode
of digital quantity
00000~11111 00000 - P S T
This parameter is used to reverse the polarity of the digital quantities. It is a binary
number. Each bit corresponds to a digital input. 0 indicates that the polarity does not
change. 1 indicates to reverse the polarity of the digital quantity corresponding to this
-96-
bit. The corresponding relationships between each bit and the digital quantity are:
BIT4 BIT3 BIT2 BIT1 BIT0
RPC PLL CLA ZRS SON
Details (Refer to chapter 4.5.8.3 for detailed description of the signs of the digital
quantities) :
ON-OFF signs of Available
BIT Function name
CN1 mode
BIT0 SON Servo enabling P S T
BIT1 ZRS Zero speed clamp-on P S T
BIT2 CLA Alarm clearance P S T
BIT3 PLL Pulse input inhibit P - -
Retention pulse
P - -
BIT4 RPC clearance
Speed reversing - S -
6.4.2 Analog input / output adjustment

Available
Offset voltage of AI Setting range Default Unit
FP3.20 mode
VA
-2.000~2.000 0.000 V - S T
Available
Offset voltage of AI Setting range Default Unit
FP3.23 mode
TA
-2.000~2.000 0.000 V P S T
This parameter can be used to adjust the AI1 and AI2 to improve the effective
accuracy for the analog input.
Due to zero drift of the AI devices and other reasons, the actual AI corresponding
value may deviate from the expected value. At this time it can be eliminated by setting
the offset of AI. Similarly, the deviation of the actual AO value from the expected
corresponding value caused by zero drift of AO devices and other reasons can be
eliminated by setting the offset of AO.
The meaning of the analog offset voltage is shown in the figure as below:
-97-
For example, after the analog setting signal is connected into the AI terminal (VA) of
the drive, even though the analog setting signal is 0, the front panel displays the
analog speed command voltage (dp-An1) is 0.02V. On this condition, parameter
FP3.20 should be set as 0.02. The drive will automatically subtract 0.02V from the AI
value received. If the front panel displays the analog speed command voltage is
-0.02V, parameter FP3.20 should be set as -0.02. The drive will automatically add
0.02V to the AI value received.
Setting Available
Default Unit
FP3.30 AO 1 selection range mode
0~7 0 - P S T
Setting Available
Default Unit
FP3.32 AO 2 selection range mode
0~7 0 - P S T
This group of parameters is used to select the monitoring parameters to be outputted
in analog form.
Setting
Parameter Definition Relative parameters
value
0 Motor speed
Output
1
torque
Output
2 Adjust FP3.33 to set the
FP3.30 current
corresponding analog output
AO 1 3 Bus voltage
signal.
selection Speed
4
setting
Torque
5
given
6~7 Reserved
0 Motor speed
FP3.32 Adjust FP3.33 to set the
Output
AO 2 1 corresponding analog output
torque
selection signal.
Output
2
current
3 Bus voltage
Speed
4
setting
-98-
Torque
5
given
6~7 Reserve
Setting Available
Default Unit
FP3.31 Voltage gain of AO 1 range mode
0~1000 500 - P S T
Setting Available
Default Unit
FP3.33 Voltage gain of AO 2 range mode
0~1000 500 - P S T
This group of parameters defines the relationships between the analog output voltage
and its corresponding setting. When the analog output voltage exceeds the set upper
limit or lower limit range, the part beyond will be calculated with the upper limit or
lower limit.
Detailed meaning of the analog output is selected by FP3.30 and FP3.32.
Corresponding setting of the lower and upper limit are expressed by percentages.
The maximum is taken as 100% and the determination of the maximum is listed in the
table below:
FP3.30 and
Outputs Maximum
FP3.32
0 Motor speed -
1 3 times of the servo motor rated
Output torque
torque
2 Output 3 times of the servo motor rated
current current
3 Bus voltage -
4 Speed setting -
5 Torque 3 times of the servo motor rated
setting torque
Take a 400W servo drive as an example. Output the actual speed from the analog
output 1 terminal (AO1) to observe, so 10V corresponds to 3000r/min and 0V
corresponds to 0r/min. On this condition, set FP3.30=0, Pc.36=0.00, Pc.38=8.00,
Pc.37=0.0, Pc.39=100.0, the relationship between the actual speed setting and the
output voltage is shown in the figure as below:
-99-
Note:
1. AO1 means the signal output from the AO1 terminal (AO1 pin21) and AO1 means
the signal output from the AO2 terminal (AO2 pin25). The output signal has no
directional properties and stands for the absolute value of the setting signal.
2. The maximum value of the motor speed, speed setting and bus voltage depends
on the power grade of the drive.
Setting Available
Offset voltage of Default Unit
FP3.34 range mode
AO1
-2.00~2.00 0.00 V P S T
Setting Default Available
Offset voltage of Unit
FP3.35 range value mode
AO2
-2.00~2.00 0.00 V P S T
This parameter can be used to adjust the AO1 and AO2 to improve the effective
accuracy for the analog input. Due to zero drift of the AI devices and other reasons,
the actual AO corresponding value may deviate from the expected value. At this time
it can be eliminated by setting the offset of AO. Similarly, the deviation of the actual
AO value from the expected corresponding value caused by zero drift of AO devices
and other reasons can be eliminated by setting the offset of AO.
Please refer to FP3.20 and FP3.23 for the detailed setting.
Before
setting
After
setting
FP3.34
FP3.35
6.4.3 Switch input / output settings

FP3.40 Travel limit switch
-100-
range mode
shield
0~1 0 - P S T
This parameter is used to set the input signals of the forward travel limit terminal (PSL
pin 3) and reverse travel limit terminal (RVL pin 4) of CN1 are active or inactive. If the
function of the travel limit switch needs to be shielded, set this parameter.
0: Signals of the travel limit terminals are inactive;
1: Signals of the travel limit terminals are active.
If PSL and RVL are connected with COM-, the state is normal and if they are
disconnected with COM-, alarm will occurs.
Wiring terminal of State (with
State of the drive
CN1 COM- )
PSL Connecting
Normal working
RVL Connecting
Forward travel limit alarm
PSL Disconnecting
AL-LT1。
Reverse travel limit alarm
RVL Disconnecting
AL-LT2。
Note:
1. If AL-LT1 or AL-LT2 occurs, the servo drive will stop at the stopping mode set by
FP4.30.
2. The clearance of AL-LT1 or AL-LT2: If the travel limit alarm takes effective, the
reverse command will be sent to the drive, and then the motor will be out of the travel
limit zone and report the automatic clearance of the alarm.
Setting Available
Default Unit
FP3.41 E-stop shield range mode
0~1 0 - P S T
This parameter is used to set the input signal of the emergency stop terminal (EMG
pin 39) is active or inactive. If the function of the E-stop needs to be shielded, set this
parameter.
0: Signal of the emergency stop terminal is inactive;
1: Signal of the emergency stop terminal is active.
If EMG is connected with COM-(NC), the state is normal; if the terminal is
disconnected with COM-, then AL-EST will occur.
Note:
1. If AL-EST occurs, the servo drive will stop at the stopping mode set by FP4.30.
-101-
2. The clearance of AL-EST: Please ensure there is no danger, and then clear the
alarm signal (i.e. connecting EMG with COM). If the alarm is displayed to be cleared
(CLA function), it is necessary to enable the servo drive again, and the system will
work normally.
Setting Available
Range of position Default Unit
FP3.50 range mode
reaching
0~20000 100 pulse P - -
This parameter is used to set the range of position reaching. When the deviation
between the position feedback pulse and position command pulse are in this range, it
is considered that it has reached the position and the output transistor of the position
reaching terminal (PLR pin11) signal comes into conduction.
Setting Available
Range of speed Default Unit
FP3.54 range mode
reaching
0~1000.0 30.0 r/min - S -
This parameter is used to set the range of speed reaching. When the deviation
between the speed feedback pulse and speed command pulse are in this range, it is
considered that it has reached the speed and the output transistor of the speed
reaching terminal (SR pin30) signal comes into conduction.
Setting Available
Default Unit
FP3.55 Zero speed range range mode
0~1000.0 50.0 r/min P S T
This parameter is used to set the zero speed range. When the absolute value of the
speed feedback is in this range, it is considered as zero speed and the output
transistor of the zero speed terminal (ZSO pin29) signal comes into conduction.
Setting Available
Locked time of servo Default Unit
FP3.56 range mode
after braking
100~5000 100 ms P S T
This parameter is used to set the locked time of the servo after braking in the locked
state. The servo is OFF in the locked state, the output transistor of the brake releasing
terminal (BRK pin 9) signal turns off. At this time, the servo will continue to be locked
-102-
for a period of time so that the motor will not rotate during the action of the relay. Refer
to chapter 5.1.10 for the sequence relationship.
Braking delay time of Setting Available

Default Unit
FP3.57 the electromagnetic range mode
brake 0~5000 1000 ms P S T
This parameter is used to set the braking delay time of the electromagnetic brake.
The servo is OFF or an alarm occurs in the running state, in this condition, the speed
may be relatively high, so the output transistor of the brake releasing terminal (BRK)
signal can be turned off after a delay time. If the speed falls below 30r/min within the
delay time, the output transistor of the BRK signal will be turned off ahead of time.
Please refer to chapter 5.1.10 for its sequence relationship.
6.5 Extension and application (FP4 group parameters)

6.5.1 Communication setting
Setting Available
Default Unit
*FP4.00 Communication mode range mode
0~1 1 - P S T
This parameter is used to select the communication mode. The communication
modes are:
0: RS232;
1: RS485.
Setting Available
Local communication Default Unit
FP4.01 range mode
address
0~31 1 - P S T
This parameter is used to set the communication address of the local drive for RS485
serial communication.
Setting Available
Communication baud Default Unit
FP4.02* range mode
rate selection
0~4 0 - P S T
This parameter is used to select the communication baud rate. Available baudrate are
-103-
as follow:
0：9600bps;
1：19200bps;
2：38400bps;
3：57600bps;
4：115200bps.
Setting Available
Communication parity Default Unit
FP4.04 range mode
mode
0~17 0 - P S T
0: None (8, N, 1) for RTU;
1: Even (E, 8, 1) for RTU;
2: Odd (8, O, 1) for RTU;
3: None (8, N, 2) for RTU;
4: Even (E, 8, 2) for RTU;
5: Odd (O, 8, 2) for RTU;
6: None (N, 7, 1) for ASCII;
7: Even (E, 7, 1) for ASCII;
8: Odd (O, 7, 1) for ASCII;
Setting Available
Communication Default Unit
FP4.05 range mode
response delay time
0~200 0 ms P S T
Communication response delay time means the interval between the time when the
subordinate machine receives the response data (the machine means servo drives)
and the time when sending response data to the upper PC. If the response delay time
is longer than the processing time of the system, after completion of data processing,
-104-
the system will wait until the response delay time is over before transmitting data to
the upper PC.
Setting Available
FP4.06 range mode
overtime fault time
0~60.0 0.0 s P S T
When this parameter is set as 0.0s, it does not perform communication overtime
detection.
When it is set as other valid values, if the interval time between one communication
and the next communication exceeds the setting of the communication overtime fault
time, the servo drive will report a communication fault alarm (Er-CT).
In general, the communication overtime detection is set as inactive. In a system that
communicates continuously, the communication state can be monitored
instantaneously by setting this parameter.
Setting Available
Communication fault Default Unit
FP4.07 range mode
processing method
0~1 0 - P S T
This parameter is used to select the action of the servo drive when a communication
fault alarm occurs:
0: Alarms and stops (with the stopping mode set by parameter Pc. 52);
1: Do not alarm and continue to run.
Setting Available
FP4.08 range mode
response enabling
0~1 1 - P S T
This parameter is used to select whether a response is required when a parameter is
written through communication:
0: Response is unnecessary;
1: Response is necessary.
Setting Available
Default Unit
FP4.09 Reserved range mode
- - - P S T
-105-
6.5.2 Alarm threshold setting

Setting Available
Stopping mode Default Unit
FP4.30 range mode
selection
0~4 3 - P S T
When the servo is turned OFF and when an fault alarm occurs, this parameter is used
to set whether the dynamic brake works or not as well as the state selection of the
servo motor after stop:
Setting Action
value of
During deceleration After stopping
FP4.30
Keep the dynamic braking
0 Coast to stop
state
Keep the dynamic braking
1 Dynamic brake to stop
state
Keep the inertia running
2 Dynamic brake to stop
state
3 Coast to stop
state
The drive locks the time
4 set by FP3.56 and
state
coast to stop
Note: If the servo motor exceeds the rated speed and runs at high speed, please do
not activate the dynamic brake. If the servo motor runs at higher speed with a load
which has large inertia, please be prudent in activating the dynamic brake. Avoid by
all means activating the dynamic brake too frequently as this may damage the servo
drive.
Setting Available
Default Unit
FP4.31 Max speed limit range mode
- - r/min P S T
This parameter can be used to set the highest speed the servo motor can run. If the
absolute value of the speed command is larger than the value of this parameter, the
magnitude of the actual speed setting will be limited by this parameter; the direction is
the same as that of the original speed command. This parameter is active in all
modes.
Note: The default value of this parameter is related to the power level of the drive. The
-106-
default value of drives below 750W (including) is 5000.0 and above is2500.0. The
setting range of drives below 2.0kW is 0~5000.0 and above 2.0kW is 0~3000.0.
Setting Available
Default Unit
FP4.32 Overspeed level range mode
- 0 r/min P S T
This parameter is used to set the overspeed level of the servo motor. When the
rotation speed of the motor exceeds this speed setting, an overspeed fault alarm will
be reported.
Note: The default of this parameter is related to the power level of the drive: the
default value of drives below 750W (including 750W) is 6000.0 and the drives above
750W is 3000.0. The setting range of drives below 2.0kW (including 2.0kW) is
0~5000.0 and the drives above 2.0kW is 0~3000.0.
Setting Available
Pulse range for Default Unit
FP4.33 range mode
over-position
0~50000 20000 pulse P - -
This parameter is used to set the alarm threshold for the over-position fault (ER-oE).
In the position mode, when the number of retention pulses exceeds this setting, an
over-position fault alarm will be reported
Brake overload Setting Available

Default Unit
FP4.34 detection enabling range mode
signal 0~1 1 - P S T
This parameter is used to shield the brake overload protection function.
0: Invalid;
1: Valid.
6.6 Factory parameters (FP9 group parameters)

Setting Available
Default Unit
FP9.00 Factory password range mode
0~65535 00000 - P S T
-107-
This parameter is the factory parameter password. The factory parameters are not
open to the user. The user is advised not to try to get into this group of factory
parameters. Otherwise it may cause malfunction or damage to the drive.
6.7 State monitoring

Symbol Accuracy Unit
r00-SPd Motor speed
r00-SPd 0.1 r/min
Display the actual rotation speed of the motor.
Lower 5 bits of Symbol Accuracy Unit

r01-FP1 feedback pulse
r01-FP1 1 pulse
accumulation
Count and display the lower 5 bits of accumulated pulse fed back from the encoder of
the servo motor, with sign bit.
Medium 5 bits of Symbol Accuracy Unit

r02-FP2 1 pulse
accumulation
Count and display the medium 5 bits of accumulated pulse fed back from the encoder
of the servo motor, with sign bit.
Higher 5 bits of Symbol Accuracy Unit

r03-FP3 1 pulse
accumulation
Count and display the higher 5 bits of accumulated pulse fed back from the encoder
of the servo motor, with a sign bit.
Lower 5 bits of Symbol Accuracy Unit

r04-rP1 command pulse
r04-rP1 1 pulse
accumulation
-108-
Count and display the lower 5 bits of the number of the accumulated input pulses.
The displayed number is the pulse number before being amplified by the electronic
gear. The displayed content may not be consistent with the accumulated number of
the feedback pulses, with a sign bit.
Medium 5 bits of Symbol Accuracy Unit

r05-rP2 1 pulse
accumulation
Count and display the medium 5 bits of the number of the accumulated input pulses.
gear. The displayed content may not be consistent with the accumulated number of
the feedback pulses, with a sign bit.
Higher 5 bits of Symbol Accuracy Unit

r06-rP3 1 pulse
accumulation
Count and display the higher 5 bits of the number of the accumulated input pulses.
gear. The display content may not be consistent with the accumulated number of the
feedback pulses, with a sign bit.

r07-EP Retention pulse
r07-EP 1 pulse
Display the number of retention pulses of the position deviation counter. The 6th bit is
the sign bit.
Analog speed Symbol Accuracy Unit

r08-An1
command voltage r08-An1 0.01 V
In the speed mode: display the voltage value of the analog speed command.
In the torque mode: display the voltage value of the analog speed limit.
Analog torque Symbol Accuracy Unit

r09-An2
command voltage r09-An2 0.001 V
-109-
In the torque mode: display the voltage value of the analog torque command.
In the speed mode: display the voltage value of the analog torque limit.
Bus voltage of main Symbol Accuracy Unit

r10-ud1
circuit r10-ud1 1 V
Display the bus voltage value of the main circuit.
Bus voltage of control Symbol Accuracy Unit

r11-ud2
circuit r11-ud2 1 V
Display the bus voltage value of the control circuit.
RMS value of current Symbol Accuracy Unit

r12-cur
output current r12-cur 0.01 A
Display the RMS value of motor.

r13-Tq Current torque
r13-Tq 1 %
Display the RMS value of motor.
Drive module Symbol Accuracy Unit

r14-Tn
temperature r14-Tn 0.1 ℃
Display the current temperature of IGBT module of the drive.

r15-Ld Average load rate
r15-Ld 1 %
Display the continuous actual load. Taking the rated power of the servo motor as
100%, convert the actual value into a percentage to display.
r16-PoS Position relative to Z Symbol Accuracy Unit
-110-
pulse r16-PoS 1 pulse

Display the position of the rotor relative to Z pulse in one revolution. The unit is pulse.

r17-inE Inertia ratio of load
r17-inE 1 Time
Display the predicted value of the ratio of rotational inertia of the servo motor to that of
the load converted onto the servo motor's shaft in real-time.
Third latest fault alarm Symbol Accuracy Unit

r18-oAL
code r18-oAL - -
Second latest fault Symbol Accuracy Unit
r19-AL
alarm code r19-AL - -
Latest fault alarm Symbol Accuracy Unit
r20-ALc
code r20-ALC - -
Display the latest, second latest and third latest fault alarm codes.

r21-in Digital input state
r21-in - -
r22-ou Digital output state
r22-ou - -
This value is a hexadecimal number arranged in the sequence of the digital quantities
to indicate the state of all digital quantities. When a terminal is in ON state, its
corresponding bit is denoted as 1. When a terminal is in OFF state, its corresponding
bit is denoted as 0. Then, this binary number is converted into a hexadecimal number.
For example, 000000001011 is denoted as 00B.
The digital input state is denoted with 4 digits of hexadecimal number. The
arrangement sequence of the digital input is: (the digits not listed are filled with 0)
BIT12 BIT11 BIT10 BIT9 BIT8 BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
MCH PLC TQC PLL RPC RVL PSL SC2 SC1 EMG CLA ZRS SON
The digital output state is denoted with 2 digits of hexadecimal number. The
arrangement sequence of the digital output is:
BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
LM BRK SR ZSO PLR ALM RDY
-111-

r23-tt Motor temperature
r23-tt 0.1 ℃
Display the current temperature of motor.

r24-uE1 DSP software version
r24-uE1 - -
Display the version number of current DSP software.
FPGA software Symbol Accuracy Unit

r25-uE2
version r25-uE2 - -
Display the version number of current FPGA software.

r26-uuu Encoder feedback
r26-uuu - -
Display current value of encoder (U, V and W) feedback.
Instantaneous value of Symbol Accuracy Unit

r27-iA
phase U output current r27-iA 0.01 A
Display the instantaneous value of current phase U output current.

r28-ib
phase V output current r28-ib 0.01 A
Display the instantaneous value of current phase V output current.

r29-iAF phase U output current
r29-iAF 0.01 A
when an fault occurs
Display the instantaneous value of phase U output current when a fault occurs.
-112-

r30-ibF phase V output current
r30-ibF 0.01 A
when an fault occurs
Display the instantaneous value of phase V output current when a fault occurs.
Value of bus voltage Symbol Accuracy Unit

r31-udF
when an fault occurs r31-udF 1 V
Detailed instruction:Display the value of bus voltage when an fault occurs.

r32-Sn1 Drive serial No.1
r32-Sn1 - -
Detailed instruction:Display the drive serial No.1

r33-Sn2 - -

r34-Sn3 - -

r35-Sn4 - -

r36-Sn5 - -

r37-Sn6 - -
-113-
Operational manual for INVT SV-DB100 AC Servo drives Gain adjustment
7 Gain adjustment
7.1 General method for adjusting parameters
When the servo system oscillates or the control performance becomes not sound, you can
improve the system performance or eliminate the oscillation by adjusting the parameters of the
speed loop and position loop. Hereunder we describe the general principle and method for the
adjustment:
Gain of the speed loop: mainly used to determine the response speed of the speed loop. Under
the precondition the mechanical system does not vibrate, the larger the setting of this
parameter, the higher the response speed.
Speed loop integration time constant: the speed loop has an integrator which can reflect minor
input. This integrator can delay the operation of the servo system. Therefore, when the time
constant increases, the response becomes slower, and the required positioning setting time is
longer. When the load inertia is larger or the mechanical system is likely to vibrate, the loop
integration time parameter must be large enough to avoid the vibration of the mechanical
system.
Torque command filter: in some cases the mechanical system may resonate, generating
vibration noise of sharp tone. At this time trap wave filtering must be performed to eliminate
resonance.
Gain of the position loop: the reaction of the servo system is determined by the gain of the
position loop. When the gain of the position loop is set higher, the reaction speed will increase
and the time required for positioning will be shortened. If you want to set the gain of the position
loop to a high value, the rigidity and natural frequency of the mechanical system must be very
high.
In general case the gain of the speed loop should be ensured higher than the gain of the
position loop whenever possible. When the position gain is much higher than the speed gain,
the system may overshoot under the action of the step signal. This will seriously damage the
system performance. Various parameters of the system always limit each other. If only the gain
of the position loop increases, the command outputted by the position loop may become
unstable. This may cause the reaction of the entire servo system to become unstable. In
general cases, we can adjust the system by referring to the follow procedures:
1) First set the gain of the position loop at a lower value, then, under the precondition that
abnormal sound and vibration are not generated, gradually increase the gain of the speed loop
to the maximum.
2) Gradually decrease the gain of the speed loop while increasing the gain of the position loop.
-114-
Under the precondition that the whole response is free from overshoot and vibration, set the
gain of the position loop to the maximum.
3) Speed loop integration time constant depends on the length of the positioning time. Please
decrease this value as small as possible under the precondition that the mechanical system
does not vibrate.
4) After that, finely adjust the gain of the position loop, speed loop and the integration time
constant to find their optimal values.
Hereunder we illustrate several typical cases (in each case, only one parameter is changed
relative to a case when the parameters are appropriate):
 Parameters are appropriate
In this case the parameters are set relatively appropriate. The motor speed can closely follow
the position command, the speed has basically no overshoot, and the positioning time is
relatively short.
 Speed loop integration time constant is relatively small
The speed loop of the servo drive must have high reaction speed. When the speed fluctuates, it
indicates that the stability of the speed loop is damaged due to the shorting integration time of
the speed loop. This causes the servo motor to run unstably at fluctuating speed.
 Speed loop integration time constant is relatively large
In this case, there is no apparent difference with the case when the parameters are appropriate.
The influence of the speed loop integration on the speed follow-up position command is not
very high, but too large speed loop integration time will delay the reaction time of the speed
loop.
 Gain of the speed loop is relatively high
In this case, the motor speed will fluctuate. The influence is the same as the case when the
speed loop integration time is too short. Both of them must keep coordinated. While increasing
the gain of the speed loop, the speed loop integration time must also be increased. Otherwise
the servo system will oscillate.
 Gain of the speed loop is too low
Decreasing the gain of the speed loop will cause fluctuation of the motor speed to fluctuate. By
comparing with the case when the speed gain is too high we can know that the fluctuation
frequency of the motor speed is lower in this case which fully indicates that increasing the gain
of the speed loop can heighten the operating frequency of the system, improve the quick
response performance of the system, and effectively overcome the influence of the
interference.
 Gain of the position loop is excessively low
-115-
In the servo system, the operating frequency of the position loop is much lower than the speed
loop. When the gain of the position loop is too low, the system is difficult to eliminate the
position deviation formed during speed response. This can cause prolongation of the time
interval of the motor speed follow-up position command.
 Gain of the position loop is excessively high
In the position servo system, the gain of the position loop also affects the stability. At this time,
as the gain of the position loop is excessively high, it makes the motor speed to fluctuate.
Additionally, comparing with the case when the gain of the position loop is too low we can know
that the pure time delay of the response to the position command of the motor speed is
decreased.
 Gain of the position loop is too low
When we adjust the gain of the position loop to a low value, the motor speed follow-up position
command represents obvious lag and the positioning time is prolonged largely. The high
accuracy and high response performance of the positioning system are seriously affected.
7.1.1 Adjustment of the gain of the position loop

The position control block diagram of the SV-DB100 series servo drive is shown in the figure
below. The gain parameters that can be adjusted in the position mode are marked out on the
block diagram.
Fig. 7-1 Block diagram of position control

The general procedures for parameter adjustment in the position mode are:
1) Initial setting of the parameters
The defaults of the parameters can be recovered by the default parameter recovering operation
(see chapter 5.2.4 for details).
-116-
2) Adjustment of the gain of the position loop

When the servo motor is running with default parameters, if the system oscillation occurs with
buzz, the position gain should be adjusted smaller. If the system rigidity is relatively small, the
position gain should be adjusted larger.
3) Adjustment of the position smoothing filter
During position control, if the position pulse commands input frequency varies largely, it may be
caused by a larger impulse. At this time the position smoothing filters time constant should be
adjusted to moderate the impulse.
4) Adjustment of the electronic gear
If the pulse transmission frequency of the pulse generator is restricted, or the transmission
frequency does not meet the mechanical requirements, we can change the pulse input
frequency by adjusting the value of the electronic gear parameters to meet the requirements for
position control.
5) Adjustment of position feed-forward
In the case the retention pulse is large or fault-free follow-up is required, we can improve the
position follow-up performance by adjusting the speed feed-forward gain parameter andspeed
feed-forward gain filter parameter. However, it should be noted that if the speed feed-forward
gain is too large, it may cause system oscillation.
6) Frequency division of the feedback pulse output
If the feedback pulse needs to be outputted, the frequency division coefficient of pulse output
can be used to change the frequency of the output pulse.
7.1.2 Adjustment of the gain of the speed loop

The speed control block diagram of the SV-DB100 series servo drive is shown in the figure
below. The gain parameters that can be adjusted in the speed mode are marked on the block
diagram.
-117-
FP0.44
FP0.54
FP0.46
FP0.55
FP0.47
FP0.56
FP0.48
FP0.57
FP0.49
Internal speed command

Speed command Speed Low-pass
Notch filter
processing controller filter
External speed command
FP2.00 FP1.23 FP2.04

Speed test
filter FP2.01 FP1.24 FP2.09 Torque
controller
FP2.05 FP1.25
FP2.03
FP2.06 FP1.26
FP2.08
FP2.12 FP1.27
FP1.28
Encoder
frequency Encoder Motor
division
FP0.06
FP0.07
Fig. 7-2 Block diagram of speed control

The general procedures for parameter adjustment in the speed mode are:
2) Adjustment of the gain of the speed loop
When the servo motor is running with default parameters, if the system oscillation occurs with
buzz, the speed gain should be adjusted smaller. If the system rigidity is relatively small or the
speed fluctuates largely, the speed gain should be adjusted larger.
3) Adjustment of the speed integration time constant
When the gain of the speed loop is increased, the speed integration time constant should be
increased at the same time. Similarly, when the gain of the speed loop is decreased, the speed
integration time constant should be decreased at the same time.
4) Adjustment of the ACC/DEC time
If the speed varies violently during starting, it may cause large impulse or even overcurrent. At
this time we adjust the ACC time to smoothen the speed rise. Similarly, we can adjust the DEC
time to smoothen the speed fall during stopping.
5) S curve ACC/DEC adjustment
If the requirement for smooth variation of speed can not be met by adjusting the ACC/DEC time,
we can adjust the S curve ACC/DEC time to make it change more smoothly.
6) Adjustment of the speed smoothing filter
In the case where the analog speed command is inputted, we can adjust the speed smoothing
-118-
filter time constant to make the speed change smoothly.

7) Adjustment of speed feed-forward
If the speed follow-up performance is still poor after above parameter adjustment, we can
adjust the torque feed-forward gain to improve the speed follow-up performance. It should be
noted however that too large torque feed-forward gain may affect the stability of the system.
8) Adjustment of speed filter
The performance of the speed loop can be improved by adjusting FP2.04/FP2.09 and
FP2.03/FP2.08.
9) Adjustment of trap wave filtering
See chapter 7.2.
If the feedback pulse of the encoder needs to be outputted, the frequency division coefficient of
pulse outputcan be used to change the frequency of the output pulse.
7.1.3 Adjustment of the gain of the torque loop

The torque control block diagram of the SV-DB100series servo drive is shown in the figure
below. The gain parameters that can be adjusted in the torque mode are marked out on the
block diagram.
Fig. 7-3 Block diagram of torque control

The general procedures for parameter adjustment in the torque mode are:
2) Adjustment of the torque smoothing filter
-119-
In the case the analog torque command is inputted, we can adjust the torque smoothing filter
time constant to make the torque change smoothly.
If the feedback pulse of the encoder needs to be outputted, the frequency division coefficient of
pulse output can be used to change the frequency of the output pulse.
7.2 Suppression of mechanical resonance

The mechanical system has a certain resonant frequency. If the response speed of the servo is
improved, the system may resonate (oscillation and abnormal noise) near the mechanical
resonant frequency. The resonance of the mechanical system can be effectively suppressed by
setting the parameters of the trap wave filters.
The trap wave filters achieve the goal of suppressing mechanical resonance by decreasing the
gain of certain frequency. We can set the frequency to be suppressed as well as the
suppression extent with relevant parameters.
This servo drive has two trap wave filters which can be set with FP1.23, FP1.24, FP1.25 and
FP1.26, FP1.27, FP1.28 respectively. The position of the trap wave filters in the speed loop is
as shown in Fig. 7-2.
Note: for the servo system, the trap wave filter is a kind of lagging factor. Therefore, incorrect
setting of the trap wave filters or too large suppression extent may strengthen vibration
sometimes.
Fig. 7-4 Schematic diagram of setting of the trap wave filters
-120-
7.3 Gain switching function

Gain switching operation is performed through internal data or external signal:
1) Can switch to lower gain to suppress vibration in the state when the motor is stopped (the
servo is locked);
2) Can switch to higher gain to shorten the positioning time in the state the motor is stop;
3) Can switch to high gain to obtain better command follow-up performance in the state when
the motor is running.
4) Can switch between different gain settings through external signal according to the
conditions of load, equipment and so on.
Here demonstrating how to improve the response performance in the position control mode by
the gain switching function: in order to get better response performance and make the servo
motor position quickly, we set FP2.21=1, FP2.22=5, FP2.25=30.0. At this time, when no pulse
st
is inputted, the system uses the 1 gain for adjustment. After the pulse command is inputted, it
nd
smoothly switches to the 2 gain. After the command input stops, in 2ms, if the speed falls
st
below the setting of FP2.25, it will switch to the 1 gain. The whole process is shown in the
figure below:
Fig. 7-5 Schematic diagram of gain switching

During positioning, generally, the speed integration function in running state of the motor can
be deactivated to raise the gain and thus improve the response performance.
While after it has stopped, the gain to suppress the motor vibration can be decreased.
-121-
Operational manual for INVT SV-DB100 AC Servo drives Communication function
8 Communication function
8.1 General
The servo drive is provided with two types of communication interfaces: RS485 and RS232.
The PC or NC can realize asynchronous serial semiduplex communication with 32 servo drives
simultaneously through RS485 interface. The communication function has realized the
following functions:
 Read/write the function parameters of the servo drives
 Monitor the operating state of the servo drives
 Form a multi-axis control system
8.2 Topological structure
SV-DB100 series servo drive is connected in the “Single Master Multi-slave” control network
with RS232/RS485 bus.
8.2.1 Communication with single set
8.2.2 Communication with multiple sets

Can run and operate 32 servo drives on one bus.
-122-
8.3 Communication protocol

The SV-DB100 series servo drive is provided with two types of communication interfaces:
RS485 and RS232. It adopts international standard Modbus communication protocol to perform
master-slave communication. The user can realize centralized control through PC/PLC, upper
control PC, etc. (set the control command, running frequency of the servo drives, modify
relevant function codes, monitor and control the operating state and fault information of the
servo drives and so on) to adapt specific application requirements.
8.3.1 Protocol Content

The Modbus serial communication protocol defines the frame content and usage format in
asynchronous transmission which includes: master polling, and the format of the broadcast
frame and the slave answering frame. The frame of the master includes: the slave address (or
the broadcast frame), commands, digit and error checkout. The slave answering also applies
the same structure: action confirmation, digit returning and error checkout. If there is a mistake
during the frame receiving of the slave or the slave can not finish the action which the master
requires, it will respond an error frame to the master as a response.
8.3.2 Protocol instructions

The communication protocol of the SV-DB100 series servo drives is an asynchronous serial
Master-Slave communication protocol. The master is the only device in the network to build up
the protocol (named as inquiry/command), while the other devices (the slaves) can respond to
or do action to the inquiry/command of the master through providing digits. The master in this
manual means PC, industrial control devices and PLC. The slaves mean the servo drives and
other control devices with the same communication protocol. The master can communicate
-123-
with a certain salve, as well as, send broadcast message to all slaves. For the
separately-visiting inquiry/command of the master, the slave should return a message as the
response. While for the broadcast message, the salve needs not to do so.
8.3.3 Communication Protocol Format

Modbus protocol supports both RTU and ASCII mode. The user can select whatever they
prefer as well as the serial communication parameters, such as, the baud rate and the
checkout means. All the devices on the same Modbus network should select the same
transmission mode and serial parameters during configuring each control devices.
8.3.3.1 ASCII mode
When the control device is set as ASCII communication mode on the Modbus network, every
8bit byte in the message is sent as two ASCII characters. The advantage of this mode is the
time interval of byte sending can achieve 1m without mistakes.
Table 8-1: The message frame in ASCII mode
The start Device Command LRC
Data The tailed
bit address code checkout
2 2 n 2 2
1 character
characters characters characters characters characters
As table 1 showed, in the message of ASCII mode, the start bit is “:” (ASCII code 3AH) and the
tailed is the line break (ASCII code 0DH, 0AH). The device on the network is detecting “:”
during the transmission. Each device decodes the next address field when receiving a “:” to
estimate the owner. The device corresponds to the address field continues to receive other field
until the line break appears. Except for the start bit and the tailed, the transmitting characters
used in other fields are 0…..9, A…..F (hex) and the ASCII codes are also used to express
characters. In the ASCII mode, LRC is used in the message to check the error.
8.3.3.2 RTU mode
When the control device is set as RTU mode, every 8bit byte in the message frame includes
two 4Bit hex characters.
Table 8-2: The message frame in RTU mode
Device Command LRC
The start bit Data The tailed
address code checkout
T1-T2-T3-T4 8Bit 8Bit n 8Bit(s) 16Bit T1-T2-T3-T4
The Modbus minimum idle time between frames should be no less than 3.5 bytes. The network
device is detecting, even during the interval time, the network bus. When the first field (the
address field) is received, the corresponding device decodes next transmitting character. When
the interval time is at least 3.5 byte, the message ends.
-124-
The whole message frame in RTU mode is a continuous transmitting flow. If there is an interval
time (more than 1.5 bytes) before the completion of the frame, the receiving device will renew
the uncompleted message and suppose the next byte as the address field of the new message.
As such, if the new message follows the previous one within the interval time of 3.5 bytes, the
receiving device will deal with it as the same with the previous message. If these two
phenomena all happen during the transmission, the CRC will generate a fault message to
respond to the sending devices.
When the control device is set as RTU communication mode (remote terminal unit), every 8bit
byte in the message includes two 4Bit hex characters. Compared with ACSII mode, this mode
can send more data at the same baud rate.
8.3.4 Command code and the communication data instructions

8.3.4.1 Command code: 03H
Function: read N words (can read no more than16 words continously).
For example, the servo drive with the salve address of 01H, if its starting address is 0601H,
read 2 words continuously, and then the structure of the frame is:
Table 8-3 The RTU master device request command
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 01H
CMD 03H
High byte of start address 06H
Low byte of start address 01H
High byte of data number 00H
Low byte of data number 02H
Low byte of CRC CHK 95H
High byte of CRC CHK 43H
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
Table 8-4 The RTU slave device reply
ADDR 01H
CMD 03H
Returned byte number 04H
Higher byte of 0004H 00H
Low byte of 0004H 00H
High byte of 0005H 00H
Low byte of 0005H 00H
-125-
Low byte of CRC CHK FAH

High byte of CRC CHK 33H
Table 8-5 The ASCII master device request command
START ‘:’
‘0’
ADDR
‘1’
‘0’
CMD
‘3’
‘0’
High byte of start address
‘6’
‘0’
Low byte of start address
‘1’
‘0’
High byte of data number
‘0’
‘0’
Low byte of data number
‘2’
LRC CHK Hi ‘F’
LRC CHK Lo ‘3’
END Lo CR
END Hi LF
Table 8-6 The ASCII slave master device reply
START ‘:’
‘0’
ADDR
‘1’
‘0’
CMD
‘3’
‘0’
Returned byte number
‘4’
‘0’
Higher byte of 0401H
‘0’
‘0’
Low byte of 0401H
‘0’
High byte of 0402H ‘0’
-126-
‘0’
‘0’
Low byte of 0402H
‘0’
LRC CHK Lo ‘8’
LRC CHK Hi ‘F’
END Lo CR
END Hi LF
Function: write one word (word)
For example, write 5000(1388H) into address 002EH, slave device address 02H. And then the
structure of the frame is:
Table 8-7 The RTU master device request command
T1-T2-T3-T4 (transmission time of 3.5
START
bytes)
ADDR 02H
CMD 06H
High byte of data address 00H
Low byte of data address 2EH
High byte of write content 13H
Low byte of write content 88H
Low byte of CRC CHK E4H
High byte of CRC CHK A6H
END
bytes)
Table 8-8 The RTU slave device reply command
START
bytes)
ADDR 02H
CMD 06H
High byte of data address 00H
Low byte of data address 2EH
High byte of write content 13H
Low byte of write content 88H
Low byte of CRC CHK E4H
-127-
High byte of CRC CHK A6H

END
bytes)
Table 8-9 The ASCII master device request command
START ‘:’
‘0’
ADDR
‘2’
‘0’
CMD
‘6’
‘0’
High byte of data address
‘0’
‘2’
Low byte of data address
‘E’
‘1’
High byte of write content
‘3’
‘8’
Low byte of write content
‘8’
LRC CHK Hi ‘2’
LRC CHK Lo ‘F’
END Lo CR
END Hi LF
Table 8-10 The ASCII slave master device reply
START ‘:’
‘0’
ADDR
‘2’
‘0’
CMD
‘6’
‘0’
High byte of data address
‘0’
‘2’
Low byte of data address
‘E’
‘1’
High byte of write content
‘3’
Low byte of write content ‘8’
-128-
‘8’
LRC CHK Hi ‘2’
LRC CHK Lo ‘F’
END Hi CR
END Lo LF
Function: diagnosis
Table 8-11 Meaning of sub-function codes
Sub-function Code Description
0000 Return to inquire information data
For example: The inquiry information string is same as the response information string when
the loop detection to address 01H of driver is carried out.
Table 8-12 The RTU request command
ADDR 01H
CMD 08H
High byte of sub-function code 00H
Low byte of sub-function code 00H
High byte of data content 12H
Low byte of data content ABH
Low byte of CRC ADH
High byte of CRC 14H
Table 8-13 The RTU reply command
START
bytes)
ADDR 01H
CMD 08H
High byte of sub-function code 00H
Low byte of sub-function code 00H
High byte of data content 12H
Low byte of data content ABH
Low byte of CRC ADH
High byte of CRC 14H
-129-

END
bytes)
Table 8-14 The ASCII request command
START ‘:’
‘0’
ADDR
‘1’
‘0’
CMD
‘8’
‘0’
High byte of sub-function code
‘0’
‘0’
Low byte of sub-function code
‘0’
‘1’
High byte of data content
‘2’
‘A’
Low byte of data content
‘B’
LRC CHK Hi ‘3’
LRC CHK Lo ‘A’
END Hi CR
END Lo LF
Table 8-15 The ASCII reply command
START ‘:’
‘0’
ADDR
‘1’
‘0’
CMD
‘8’
‘0’
High byte of sub-function code
‘0’
‘0’
Low byte of sub-function code
‘0’
‘1’
High byte of data content
‘2’
‘A’
Low byte of data content
‘B’
-130-
LRC CHK Hi ‘3’

LRC CHK Lo ‘A’
END Hi CR
END Lo LF
8.3.5 Error checkout of the communication frame

The error checkout of the frame can be divided into two parts: the bit checkout of the byte and
the whole data checkout of the frame (CRC check or LRC check).
8.3.5.1 Bit checkout of the byte
The user can select different bit checkouts or non-checkout, which impacts the check bit setting
of each byte.
The definition of even checkout: add an even check bit before the data transmission to illustrate
the number of “1” in the data transmission is odd number or even number. When it is even, the
check byte is “0”, otherwise, the check byte is”1”. This method is used to stabilize the parity of
the data.
The definition of odd checkout: add an odd check bit before the data transmission to illustrate
the number of “1” in the data transmission is odd number or even number. When it is odd, the
check byte is “0”, otherwise, the check byte is”1”. This method is used to stabilize the parity of
the data.
For example, when transmitting “11001110”, there are five “1” in the data. If the even checkout
is applied, the even check bit is “1”; if the odd checkout is applied; the odd check bit is “0”. The
even and odd check bit is calculated on the check bit position of the frame. And the receiving
devices also carry out even and odd checkout. If the parity of the receiving data is different from
the setting value, there is an error in the communication.
8.3.5.2 CRC CRC check
The checkout uses RTU frame format. The frame includes the frame error detection field which
is based on the CRC calculation method. The CRC field is two bytes, including 16 figure binary
values. It is added into the frame after calculated by transmitting device. The receiving device
recalculates the CRC of the received frame and compares them with the value in the received
CRC field. If the two CRC values are different, there is an error in the communication.
During CRC, 0*FFFF will be stored. And then, deal with the continuous 6-above bytes in the
frame and the value in the register. Only the 8Bit data in every character is effective to CRC,
while the start bit, the tailed and the odd and even check bit is ineffective.
The calculation of CRC applies the international standard CRC checkout principles. When the
user is editing CRC calculation, he can refer to the relative standard CRC calculation to write
the required CRC calculation program.
-131-
Here provided a simple function of CRC calculation for the reference (programmed with C
language):
unsigned int crc_cal_value(unsigned char *data_value,unsigned char data_length)
{
int i;
unsigned int crc_value=0xffff;
while(data_length--)
{ crc_value^=*data_value++;
for(i=0;i<8;i++)
{
if(crc_value&0x0001)crc_value=(crc_value>>1)^0xa001;
else crc_value=crc_value>>1;
} }
return(crc_value);
}
In ladder logic, CKSM calculated the CRC value according to the frame with the table inquiry.
The method is advanced with easy program and quick calculation speed. But the ROM space
the program occupied is huge. So use it with caution according to the program required space.
8.3.5.3 LRC check
The LRC check is the value adding from Address to Date Content. For example, the LRC check
of the 8.3.4.2 communication information is 0×02+0×06+0×01+0×09+0×13+088=0AD, and
then complementary code=0×53.
8.3.6 Address definition of communication data

This chapter is the address definition of communication data used to control the running of the
servo drives, acquire the state information of the servo drives and set relevant function
parameters of the servo drives and so on.
The servo drive has 4 groups of function codes: FP0.XX, FP1.XX, FP2.XX, FP3.XX, FP4.XX,
FP9.00 and rXX.XXX. The first 3 groups of function codes are not only readable but also can
be modified through communication. rXX.XXX is readable. The writing is invalid.
The address of the function codes are composed of two 8-bit, expressed with the hexadecimal
system. The first 8-bit indicates the group number of the function codes: FP0 group is 00H, FP1
group is 01H, FP2 group is 02H, FP3 group is 03H, FP4 group is 04H, FP9 group is 05H, rXX
group is 06H. The last 16-bit indicates the hexadecimal expression of the serial number of the
function code. For examples, the address of function code FP0.25 is 0019H and the address of
FP4.31 is 041FH.
-132-
Table 8-6 Special function codes

Function Address R/W
Explanation of data meaning
description definition characteristics
0000H: Jog end
0001H: Jog start

Communication
0002H: FWD jog start
control 1000H W
0003H: REV jog start
command
0004H FWD jog end
0005H: REV jog end
0001H: FWD running
0002H: REV running
Servo state 1001H R
0003H: Servo drive standby
0004H: in fault
EERPROM 0002H: parameter default
1002H W
writing recovering
See description of Pd.18 for the
arrangement sequence of the
digital quantities. In which, 3
signals – EMG, PSL and RVL –
Control quantity 1003H W/R
cannot be controlled through
communication. Bit 13 is the
communication control enabling
bit.
Data storage Storage step length (unit: cycle
1004H W/R
control number of the carrier wave)
Storage manner
1005H 0000H: store only 1 screen W/R
0001H: cyclic storage
Storage command
1006H 0000H: end storage W/R
0001H: start storage
1008H Channel 1 function code selection W/R
1009H Channel 2 function code selection W/R
-133-
Function Address R/W

Explanation of data meaning
description definition characteristics
2000H Channel 1 data starting address R
3000H Channel 2 data starting address R
Internal speed/speed limit 1
0700H W/R
(FP0.46) higher 16 bits
0701H W/R
(PA.10) Higher 16 bits
Particular Internal speed/speed limit 3
0702H W/R
address (Pc.10) Higher 16 bits
0703H W/R
(Pc.11) Higher 16 bits
0704H Lower 16 bits of speed feedback R
0705H Higher 16 bits of speed feedback R
8.3.7 Fault Responses

The slave uses functional code fields and fault addresses to indicate it is a normal response or
some error occurs (named as objection response). For normal responses, the slave shows
corresponding function codes, digital address or sub-function codes as the response. For
objection responses, the slave returns a code which equals the normal code, but the first byte
is logic 1.
For example: when the master sends a message to the slave, requiring it to read a group of
address data of servo device function codes, there will be following function codes:
00000011 (Hex 03H)
For normal responses, the slave responds the same codes, while for objection responses, it will
return:
10000011 (Hex 83H)
Besides the function codes modification for the objection fault, the slave will respond a byte of
abnormal code which defines the error reason.
When the master receives the response for the objection, in a typical processing, it will send
the message again or modify the corresponding order.
Table 8-17 Meaning of error code
Modbus abnormal code
Code Name Meaning
Illegal Receiving function codes from the upper devices is not
01H
function allowable. This may because these function codes can only
-134-
Modbus abnormal code

Code Name Meaning
be applied to new devices or the slave device is dealing with
this requirement in a wrong situation.
Illegal For servo drives, the requirement digital address is not
02H digital allowable; especially the mix of the register address and
address transmitting byte numbers is invalid.
Illegal
The digital value received is beyond the range of address
03H digital
parameters, leading the parameter modification invalid.
value
In the frame message sent by the upper devices, if the CRC
Check check bit of RTU format or the LRC check bit of ASCII format
11H
error is different from the check number calculated by the below
devise, an check error will be reported.
-135-
Operational manual for INVT SV-DB100 AC Servo drives Fault processing
9 Fault processing
9.1 Meanings of the fault alarm codes and countermeasures
No. Code Name Causes Countermeasures

EEPROM
1 Er-EEP 1. EEPROM is damaged 1. Replace the drive
fault
1. The encoder is not
connected 1. Connect the encoder
2. The encoder connector 2. Check the encoder
Encoder line becomes loose connector or replace the
2 Er-Ec1
break fault 1 3. The line of one of the U, encoder cable
V, W phases of the 3. Replace the encoder
encoder signal cable is cable
broken
1. Reversed A/B phase of 1. Check that the phases
the encoder of the encoder are wired
3 Er-Ec2 Encoder fault 2 2. The line of one of the A, correctly
B, Z phases of the encoder 2. Replace the encode
signal cable is broken cable
1. The current sensor or
1. Replace the drive
test circuit is abnormal
2. Never power on when
4 Er-iTE Current test fault 2. Powered on when the
the motor shaft is
motor shaft is in a
rotating
non-stationary state
1. Check that the phases
1. U, V, W phases of the
of the motor cable are
motor are connected
connected correctly
reversely
2. Adjust the loop
2. Inappropriate
parameters to stabilize
Hardware parameters cause system
5 Er-oc1 the system. Adjust the
overcurrent fault divergence
value of FP0.12 smaller
3. Too short ACC/DEC
3. Set the ACC/DEC
time during
time appropriately longer
starting/stopping
4. Replace with a drive
4. Too large instant load
of higher power
-136-

1. One of U, V, W phases Replace the motor cable
Line-to-ground
6 Er-oc2 of the motor cable is or test if the motor
short circuit fault
shorted to the ground insulation is aged
1. Test the input voltage
of the grid
1. The grid voltage is high
2. Check if the built-in
2. The braking resistor is
braking resistor shorting
not connected
wiring becomes loose,
Overvoltage 3. The braking transistor is
7 Er-ou or check if the built-in
fault damaged
braking resistor is
4. Too short ACC/DEC
damaged
time during
3. Replace the drive
starting/stopping
4. Set the ACC/DEC
time longer
1. The grid voltage is low
Undervoltage 1. Test the input voltage
2. The powering-up
8 Er-uu fault of the main of the grid
snubber relay has not
bus 2. Replace the drive
picked up
1. The grid voltage is low
Undervoltage 1. Test the input voltage
2. The powering-up
9 Er-uu1 fault of the of the grid
snubber relay has not
control bus 2. Replace the drive
picked up
1. Replace with the drive
1. Run overload for a long and motor of higher
period of time power
10 Er-oL Overload fault
2. The load is too heavy in 2. Replace with the drive
a short period of time and motor of higher
power
1. U, V, W phases of the 1. Check that the phases
Line abnormality
11 Er-LnE motor are connected of the motor cable are
fault
reversely connected correctly
1. The motor speed is too 1. Replace with a motor
12 Er-oS Overspeed fault high of higher speed or check
2. Overspeed of the motor. the parameter settings
-137-

U, V, W phases of the 2. Check that the phases
motor are connected of the motor cable are
reversely connected correctly
1. Improve the
Drive 1. The temperature of the
ventilation or replace
13 Er-oH1 overtemperature IGBT module of the drive is
with a servo drive of
fault too high
higher power
1. Set the gain
parameters of the
1. Number of the retention
14 Er-oE Over-pulse fault position loop higher or
pulses is too large
set the position
feed-forward gain higher
1. Try to decrease the
1. Too high communication communication
Communication fault rate interference
15 Er-cTE
fault 2. Communication 2. Check the connection
disconnecting of the communication
cable
1. Overtime when
Write/read 1. Replace the drive
16 Er-oT reading/writing EEPROM
overtime fault 2. Replace the drive
2. Damaged EEPROM
1. The power of the built-in 1. Connect an external
braking resistor is relatively braking resistor of higher
Brake overload low power
17 Er-bcE
fault 2. The power of the 2. Replace with a
external braking resistor is braking resistor of higher
relatively low power
1. Adjust FP0.12 smaller
1. IPM module detects out to decrease the
IPM module
18 Er-iPo overcurrent or maximum output torque
fault
undercurrent or replace with a drive of
higher power
Power supply 3-phase input power Check the input voltage
19 Er-dP
input phase loss supply is phase loss or or the wire is loose or
-138-

seriously uneven. disconnected.
1.Vibration in stopping
1.Improve the
Inertia exceeds 3.5s
mechanical rigidity
20 Er-INE identification 2. Too short ACC time
2.Prolong FP1.07
fault 3. The identification speed
3.Increase FP1.06
is below 150r/min
Motor
Ensure the motor model
21 Er-DrE parameters Wrong FP0.00 setting
and the drive model
matching fault
9.2 Meanings of the warning codes
No. Warning Name Description

Forward travel limit This warning signal is generated when forward
1 AL-LT1
warning travel is limited (PSL terminal disconnects)
Reverse travel limit This warning signal is generated when reverse
2 AL-LT2
warning travel is limited (RVL terminal disconnects)
This warning signal is generated when the
Emergency stop
3 AL-EST emergency stop button acts (EMG terminal
warning
disconnects)
Low voltage of the
This warning signal is generated when the bus
4 AL-Pof main circuit
voltage is too low.
warning
Communication In the case of communication overtime or
5 AL-cTE abnormality abnormal, if Pc.26=1, this warning signal is
warning generated.
See chapter 5.2.6 for the detailed method to clear the alarm or warning display when a fault
alarm or warning occurs.
-139-
Operational manual for INVT SV-DB100 AC Servo drives Appendix A
Appendix A List of function parameters
P – position mode; S – speed mode; T – torque mode.

The function codes prefixed with sign “*” indicate the setting of these parameters can only take
effect after the system resets, restarts, or control circuit is powered off and repowered.
Function
code
FP0 Basic control
Matching motor
FP0.00 - 200~599 - PST
selection
FP0.03* Mode selection - 0~6 0 PST
Internal servo
FP0.04 - 0~1 0 PST
enabling
FP0.05 Jog speed r/min 0.0~1000.0 200.0 PST
Numerator of the
frequency division
FP0.06* - 0~30000 10000 PST
pulse output
Denominator of the
frequency division
FP0.07* - 0~30000 0 PST
pulse output
FP0.11 Max torque limit % 0.0~300.0 300.0 PST
FP0.12 Internal torque limit % 0.0~300.0 - PS
Power of the external
FP0.13 W 0~1500 0 PST
braking resistor
Resistance of the
FP0.14 external braking Ω 1~100 1 PST
resistor
Default monitoring
FP0.15* - 0~37 0 PST
parameters
Parameter
FP0.16 modification - 0~1 0 PST
operation locking
Communication
FP0.17 EEPROM write - 0~1 0 PST
selection
FP0.23* Pulse input - 0~2 0 P
FP0.24* Pulse input direction - 0~1 0 P
-140-
Function
code
reversing
st
Numerator of the 1
FP0.25 - 1~65535 1 P
electronic gear
Denominator of the
FP0.26 st - 1~65535 1 P
1 electronic gear
nd
Numerator of the 2
FP0.27 - 1~65535 1 P
electronic gear
rd
Numerator of the 3
FP0.28 - 1~65535 1 P
electronic gear
th
Numerator of the 4
FP0.29 - 1~65535 1 P
electronic gear
Denominator of the
FP0.30 nd - 1~65535 1 P
2 electronic gear
Denominator of the
FP0.31 rd - 1~65535 1 P
3 electronic gear
Denominator of the
FP0.32 th - 1~65535 1 P
4 electronic gear
Position command
FP0.33 ms 0.0~1000.0 0.0 P
filter time
Speed
FP0.40 command/speed limit - 0~1 0 ST
selection
Speed command
FP0.42 (r/min)/v 10~1000 500 ST
input gain
Speed command filter
FP0.44 ms 0.0~1000.0 0.0 S
time
Dead zone of analog
FP0.45 V 0.000~2.000 0.000 ST
VA
Internal
FP0.46 r/min -6000.0~6000.0 100.0 ST
speed/speed limit 1
Internal
FP0.47 r/min -6000.0~6000.0 200.0 ST
speed/speed limit 2
Internal
FP0.48 r/min -6000.0~6000.0 500.0 ST
speed/speed limit 3
Internal
FP0.49 r/min -6000.0~6000.0 1000.0 ST
speed/speed limit 4
FP0.54 ACC time ms 0~20000 0 S
FP0.55 DEC time ms 0~20000 0 S
-141-
Function
code
FP0.56 S curve ACC time ms 0~1000 0 S
FP0.57 S curve DEC time ms 0~1000 0 S
FP0.58 Stopping method - 0~1 0 S
Torque
FP0.60 command/torque limit - 0~1 0 PST
selection
Torque command
FP0.62 %/V 10~300 10 PST
input gain
Torque command
FP0.64 ms 0.0~1000.0 0.0 T
filter time
Dead zone of analog
FP0.65 V 0.000~2.000 0.000 PST
TA
Internal torque
FP0.66 % -250.0~250.0 10.0 T
command
FP1 Self-turning control
Rotational inertia
FP1.02 % 0~10000 200 PST
ratio
Machine rigidity
FP1.03 - 0~31 13 PST
setting
Inertia identification
FP1.04 - 0~1 0 P
switch
Inertia identification
FP1.05 - 0~3 0 P
operation
Mechanical
FP1.06 r 0.5~10.0 1.5 P
movement
Identification of
FP1.07 inertia acceleration ms 2~200 2 P
time constan
Resonance
FP1.20 - 0~1 0 PST
frequency test valid
st
1 mechanical
FP1.21 Hz 0.0~3000.0 0.0 PST
resonance frequency
nd
2 mechanical
FP1.22 Hz 0.0~3000.0 0.0 PST
resonance frequency
st
1 trap wave center
FP1.23 Hz 50.0~3000.0 3000.0 PST
frequency
st
st
-142-
Function
code
nd
2 trap wave center
FP1.26 Hz 50.0~3000.0 3000.0 PST
frequency
nd
nd
FP2 Motor control
st
st
1 speed integration
FP2.01 ms 0.1~1000.0 21.0 PST
time constant
st
st
1 speed detection
FP2.03 ms 0.00~100.00 0.00 PST
filter time
st
nd
nd
2 speed integration
FP2.06 ms 0.1~1000.0 1000.0 PST
time constant
nd
nd
2 speed detection
FP2.08 ms 0.00~100.00 0.05 PST
filter time
nd
FP2.10 Speed feed-forward % 0.0~100.0 30.0 P
Speed feed-forward
FP2.11 ms 0.00~60.00 0.50 P
filter time
Torque
FP2.12 % 0.0~100.0 0.0 PS
feed-forward gain
Gain switching
FP2.21 - 0~1 1 PST
selection
Gain switching
FP2.22 - 0~5 0 PS
condition
Gain switching time
FP2.23 ms 0~100 0 PS
constant
Gain switching Pulse or
FP2.25 0~5000/0~500.0 100/10.0 PS
threshold r/min
Speed compensation
FP2.47 pulse 0~20000 100 P
threshold
FP2.48 Speed compensation r/min 0~500.0 0.0 P
FP3 I/O management
FP3.00 Digital 1 input - 0~11111 0 PST
FP3.20 Offset of AI VA V -2.000~2.000 0.000 ST
-143-
Function
code
FP3.23 Offset of AI TA V -2.000~2.000 0.000 PST
FP3.30 AO 1 selection - 0`7 0 PST
Voltage gain of
FP3.31 - 0~1000 500 PST
analog output 1
FP3.32 AO 2 selection - 0~7 0 PST
Voltage gain of
FP3.33 - 0~1000 500 PST
analog output 2
FP3.34 Offset of AO1 V -2.00~2.00 0.00 PST
FP3.35 Offset of AO 2 V -2.00~2.00 0.00 PST
Travel limit switch
FP3.40 - 0~1 0 PST
masking
FP3.41 E-stop masking - 0~1 0 PST
Range of position
FP3.50 pulse 0~20000 100 P
reaching
Range of speed
FP3.54 r/min 0.0~1000.0 30.0 S
reaching
FP3.55 Zero speed range r/min 0.0~1000.0 50.0 PST
Locked time of servo
FP3.56 ms 100~5000 100 PST
after braking
Braking delay time of
FP3.57 the electromagnetic ms 0~5000 1000 PST
brake
FP4 Extension and application
Communication
FP4.00* - 0~1 1 PST
mode
Local communication
FP4.01 - 0~31 1 PST
address
Communication
FP4.02* - 0~4 0 PST
baudrate selection
Communication parity
FP4.04 - 0~17 0 PST
mode
Communication
FP4.05 ms 0~200 0 PST
response delay time
Communication
FP4.06 s 0.0~60.0 0.0 PST
overtime fault time
Communication
FP4.07 fault processing - 0~1 0 PST
method
-144-
Function
code
Communication
FP4.08 - 0~1 1 PST
response enabling
FP4.09 Reserved - - - PST
Stopping mode
FP4.30 - 0~4 3 PST
selection
FP4.31 Max. speed limit r/min 0~6500.0 - PST
FP4.32 Overspeed level r/min 0~6553.5 - PST
Pulse range for over
FP4.33 10pulse 0~50000 2000 P
position
Brake overload
FP4.34 detection enabling - 0~1 1 PST
signal
Input phase loss
FP4.35 0~1 0 PST
setting
FP9 Factory parameters
FP9.00 Factory password 100 PST
Function
Name Unit Accuracy
code
r00.spd Motor speed r/min 0.1
r01.FP1 Lower 5 digits of feedback pulse accumulation pulse 1
r02.FP2 Medium 5 digits of feedback pulse pulse 1
accumulation
r03.FP3 Higher 5 digits of feedback pulse accumulation pulse 1
r04.rp1 Lower 5 digits of command pulse pulse 1
accumulation
r05.rp2 Medium 5 digits of command pulse pulse 1
accumulation
r06.rp3 Higher 5 digits of command pulse pulse 1
accumulation
r07.EP Retention pulse pluse 1
r08.An1 Analog speed command voltage V 0.01
r09.An2 Analog torque command voltage V 0.01
r10.ud1 Main circuit power bus voltage V 0.1
r11.ud2 Control circuit power bus voltage V 0.1
r12.cur Effective value of current output current A 0.01
r13.Tq Current torque % 1
r14.Tn Drive module temperature ℃ 0.1
-145-
Function
Name Unit Accuracy
code
r15.Ld Average load rate % 1
r16.PoS Position of the rotor relative to Z pulse pulse 1
r17.inE Inertia ratio of load time 1
r18.oAL The two previous fault alarm code - -
r19.AL The previous fault alarm code - -
r20.ALc Current fault alarm code - -
r21.in Digital input state - -
r22.ou Digital output state - -
r23.TT Motor temperature - -
r24.uE1 DPS software version - -
r25.uE2 FPGA software version - -
r26.uuu Encoder UVW feedback value - -
r27.iA Instantaneous value of phase U output current A 0.01
r28.ib Instantaneous value of phase V output current A 0.01
r29.iAF Instantaneous value of U phase output current A 0.01
when a fault occurs
r30.ibF Instantaneous value of phase V output current A 0.01
when a fault occurs
r31.udF Bus voltage when a fault occurs V 0.1
-146-
Operational manual for INVT SV-DB100 AC Servo drives Appendix B
Appendix B Signal arrangement diagram
B.1 CN1 pin signal arrangement:
CN2 pin No. CN2 pin No. CN2 pin No.

1 V+ Black
2 W+ Brown
3 A+ Red
4 A- Red and white
5 5V Purple
6 U+ Orange

9 B- Blue

-147-
Operational manual for INVT SV-DB100 AC Servo drives Appendix B
CN2 pin No. CN2 pin No. CN2 pin No.

13 Z- Green
15 / /
CN3 pin No. 1 2 3 4 5 6 7 8

Definition RXD GND TXD CANL / CANH RS485- RS485+
-148-
Operational manual for INVT SV-DB100 AC Servo drives Appendix D
Appendix C Plug signal of servo motor
C.1 Plug of the motor

C.1.1 Below and including 750W:
Wire sequence of the motor

No. 1 2 3 4
Yellow and
Color Brown Black Blue
green
Signal W PE V U
C.1.2 Above 750W:
Wire sequence of the motor

No. 1 2 3 4
Yellow and
Color Blue Black Brown
green
Signal PE U V W
C.2 Plug of encoder wire

C.2.1 Below and including 750W:
No. Color Signal
-149-
No. Color Signal

1 V+ Black
2 W+ Brown
3 A+ Red
4 A- Red and white
5 5V Purple
6 U+ Orange
9 B- Blue
13 Z- Green
15 / /
C.2.2 Above 750W:
No. Signal Color

1 PE Shield wires
2 5V Purple
4 A- Red and white

5 B+ Blue and white
6 C+ Green and white
7 A+ Red
8 B- Blue
9 C- Green
-150-
No. Signal Color

10 U+ Orange
11 V+ Black
12 W+ Brown
-151-
Appendix D Wiring examples
D.1 Connection with Panasonic FPG-C32T
-152-
D.2 Connection with Panasonic FP2-PP22 (AFP2434)
-153-
D.3 Connection with Panasonic FP2-PP2 (AFP2430)
-154-
D.4 Connection with Yokogawa PLC F3YP14-ON/F3YP18-ON
-155-
D.5 Connection with Yokogawa PLC F3NC32-ON/F3NC34-ON
-156-
D.6 Connection with Omron CS1W-NC133/233/433
-157-
D.7 Connection with Omron CJ1W-NC133/233/433
-158-
D.8 Connection with Mitsubishi QD75D1
-159-
D.9 Connection with Mitsubishi FX-1PG
-160-
D.10 Connection with Mitsubishi FX2N-1PG
-161-
V1.1

INVT - AC Servo-DB100 - Manual - V3.0

Uploaded by

Copyright:

Available Formats

INVT - AC Servo-DB100 - Manual - V3.0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

INVT - AC Servo-DB100 - Manual - V3.0

Uploaded by

Copyright:

Available Formats

Operational manual for INVT SV-DB100 AC Servo drives Preface

Point out potential danger which, if not avoided, may cause

Maintenance and inspection:

6.3.3 Special motor control.......................................................................................96

Appendix C Plug signal of servo motor............................................................................... 149

Other Indoor (without direct sunshine), free from

1.2 Nameplate of the servo drive

Fig. 1-1 Nameplate of the servo drive

1.3 Illustration of the nameplate

Fig. 1-2 Meanings of the model

1: 2500-wire 2: 2500-wire 3: 17-bit 4: 17-bit

1.4 Power specification

1.5 Illustrations of every parts of the servo drive

Fig. 1-3 Illustrations of every parts of 200W~5.5kW servo drives

1.6 External dimensions and installations sizes of the servo drive

Fig. 1-4 External dimensions of 100W~5.5kW servo drive

Table 1-3 External dimensions and installations sizes

● Only qualified electricians are allowed to operate on the drive device/system.

3.1 Environmental Requirement

3.1.2 Relative humidity

following figure for details:

Figure 3.1 Relationship between output current and altitude

3.1.4 Other environment requirements

3.2 Installation of the servo drive

Fig. 3-2 Mounting holes of the servo drive

3.2.2 Installation direction and spacing

Fig. 3-4 Installation of single servo drive

Fig. 3-5 Installation of several servo drives

3.2.3 Avoid intrusion of foreign objects

4 Signal and wiring

4.1 System configuration

4.1.2 Cable diameter selection

Table 4-1 Cable diameter selection

4.1.3 EMI filter selection

Drives EMI filters

4.1.4 Braking resistor selection

4.2 Wiring of the main circuit (Plug X1 and X2)

Fig. 4-2 Wiring diagram of the main circuit

U · Connect the output U, V, and W of the drive to

Surge absorber · Please refer to section 4.6 for connection of

Fig. 4-3 Wiring diagram of single phase 230V power input

Fig. 4-4 Wiring diagram of three-phase 230V power input

4.2.4 Wiring diagram of three-phase 400V power input

Fig. 4-5 Wiring diagram of three-phase 400V power input

4.3 Wiring of the encoder (plug CN2)

Fig. 4-6 Wiring of the encoder signal

Fig. 4-7 CN2 pin arrangement

CN2 pin No. Definition Cable color

4.4 Connection with the PC or HOST (CN3 plug)

Fig. 4-8 CN3 pin arrangement

4.5 I/O signal wiring (CN1 connector)

Fig. 4-9 Input/output signal connection

4.5.2 CN1 pin arrangement and signal explanation

Fig. 4-10 CN1 pin signal diagram

Symbol Pin No. Name Function

4.5.2.4 Digital input signals and their functions

Symbol Pin No. Name Function

4.5.2.7 Digital output signals and their functions

Symbol Pin No. Name Function