Scribd
Upload
108 views4 pages

ME 1761 Introduction To CAD Bearing Housing Parts NX Assignment 2

The document provides instructions for an NX CAD assignment to model parts for a bearing housing assembly. Students are to create solid models of a #10 washer, socket head screw, bushing, oil cap, bearing cover, and bearing base using the given dimensions and assembly drawings. The parts are to be placed in a zip folder named according to the specified convention and submitted on Canvas for grading out of 60 total points. Detailed steps are provided for each part, including retrieving 3D files from McMaster-Carr to use as references or to convert to the CAD file format.

Uploaded by

Carson Eshenroder
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
108 views4 pages

ME 1761 Introduction To CAD Bearing Housing Parts NX Assignment 2

The document provides instructions for an NX CAD assignment to model parts for a bearing housing assembly. Students are to create solid models of a #10 washer, socket head screw, bushing, oil cap, bearing cover, and bearing base using the given dimensions and assembly drawings. The parts are to be placed in a zip folder named according to the specified convention and submitted on Canvas for grading out of 60 total points. Detailed steps are provided for each part, including retrieving 3D files from McMaster-Carr to use as references or to convert to the CAD file format.

Uploaded by

Carson Eshenroder
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

ME 1761 Introduction to CAD

Bearing Housing Parts


NX Assignment 2
Due Date: January 30, 2022

Create solid models of the parts for assembly shown in Figure 1 below in NX. All measurements are in
SI [mm, kg, s] units unless explicitly specified.

Figure 1: Bearing Housing Assembly

Grading
Assignments will be scored as follows:

#10 Washer: 5 points


Socket Head Screw: 5 points
Oil Cap: 10 points
Bushing: 10 points
Bearing Base: 15 points
Bearing Cover: 15 points
Total 60 Points

Place all part files into a zipped (compressed) folder and submit the folder on Canvas. Name the zipped
folder using the following naming convention ME1761_SP21_NX_2_Joe_Miner.

1
Step 1: #10 Washer
Go to McMaster-CARR and search for
316 Stainless Steel Washer
Size : #10 Screw
Part : #90107A011
Download the 3-D Solidworks FILE and convert it to the NX part file. Save it in the parts folder.

Step 2: Socket Head Screw


Go to McMaster-CARR and search for
Super-Corrosion-Resistant 316 Stainless Steel Socket Head Screw
Size : #10-32 x 1/2” Long Fully Threaded
Part : #92185A989
Download the 3-D STEP FILE and convert to the NX part file. Save it in the parts folder.

Step 3: Bushing
Revolved part. Use the dimensions given in the side view shown in Figure 2 to the left of the 3D part.

Figure 2: Revolved Part Bushing

Step 3: Oil Cap


Revolved part. Use the dimensions given in the side view shown in Figure 3 to the left of the 3D part.

Figure 3: Revolved Part Oil Cap

2
Step 5: Bearing Cover
Extruded part. Use the dimensions given in the side view shown in Figure 4 to the left of the 3D part
Hints: Draw the profile shown in Figure 4 and extrude it then add the holes with method of your
choice.

Figure 4: Extruded Part Bearing Cover

Step 6: Bearing Base


Extruded part. Use the dimensions given in the views shown in Figure 5b for 3D part in Figure 5.

Hints:

1 x 45o : Use Chamfer feature to create a symmetric 1 mm x 45o chamfer on the edge of the slots.
R2: Use the edge blend feature to create 2 mm edge blend on the corners.
#10x32 UNF-2B -12.7 Deep Draw the center locations of the screw holes and then use Hole feature
to create threaded hole with following settings: Standard: Inch UNF, Size #10-32, Depth Limit :
0.5 in.

Step 7: Submission
Place the parts file and all files downloaded from McMaster-CARR into a zipped (compressed) folder
and submit the folder on Canvas. Name the zipped folder using the following naming convention
ME1761_SP22_NX_2_Joe_Miner.

3
(a) 3D-Views

(b) Dimensions

Figure 5: Extruded Part Bearing Base

You might also like