Scribd
Upload
168 views2 pages

Paper-Jam Error (GXXX Errors) : Chapter 17. Panel Messages

This document provides information about paper jam error codes in three paragraphs or less: The document describes a paper jam error code system that assigns a bit value to nine different jam errors and sums the bits to generate a three-digit error code (Gxxx). It gives an example error code of G130 indicating jams at the print drum (A08) and the sorter (B03). Next, it lists the panel displays and reset methods for two common error types: A08 for a paper jam on the print drum and A09 for a paper ejection error. It identifies specific error points and conditions for each.

Uploaded by

Karamfil 'Trun' Hristov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
168 views2 pages

Paper-Jam Error (GXXX Errors) : Chapter 17. Panel Messages

This document provides information about paper jam error codes in three paragraphs or less: The document describes a paper jam error code system that assigns a bit value to nine different jam errors and sums the bits to generate a three-digit error code (Gxxx). It gives an example error code of G130 indicating jams at the print drum (A08) and the sorter (B03). Next, it lists the panel displays and reset methods for two common error types: A08 for a paper jam on the print drum and A09 for a paper ejection error. It identifies specific error points and conditions for each.

Uploaded by

Karamfil 'Trun' Hristov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

CHAPTER 17.

PANEL MESSAGES

Paper-jam error (Gxxx Errors)


The paper-jam error number is determined by combining the errors for the paper jams involved. There
are nine different jam errors, as specified in the table below. Each error is assigned a bit, and the jam-
error number (Gxxx) is the sum of the corresponding values. The detailed error codes can be displayed by
pressing the “*” key.

Bit Corresponding value Error type Description


Bit 0 1 A10 AF original feed error
Bit 1 2 B03 Sorter: Error command 2
Bit 2 4 B07 Multi-tray: Main-unit error
Bit 3 8 B09 Multi-tray: Main-unit error
Bit 4 16 B11 Multi-tray: Tray-1 error
Bit 5 32 B17 Multi-tray: Tray-2 error
Bit 6 64 A07 Paper-feed error
Bit 7 128 A08 Paper jam on print drum
Bit 8 256 A09 Paper-ejection error

Example:
If A08 and B03 occur, the Error No. will be G130.

G130

Error type Panel display


Gxxx
Panel display Paper Jam
Remove Paper in Indicated Areas and Press [OK] Button.

[17-6]
CHAPTER 17. PANEL MESSAGES

Error type A08 [Paper jam on print drum]


Panel display
Reset method Print-drum set sensor: OFF → ON (Or switch the power on again.)
Error point Error conditions
The paper-ejection sensor was OFF when paper should have arrived, and the
410
paper sensor was OFF at 180° just before stopping.
The paper sensor was ON when the paper should have left the paper sensor
421 during feeding of long paper in long-length paper mode (paper longer than 555
mm).
430 Paper jam on print drum (error occurred during recovery movement).
Error command (Main unit: Jam error) received from the multi-tray unit.
829
During machine idling, Multi-tray feed sensor 4 is ON and Paper sensor is also ON.

Error type A09 [Paper-ejection error]


Panel display
Turn the paper-ejection sensor OFF and reset the jam, or switch the power on
Reset method
again.
Error point Error conditions
The paper-ejection sensor was ON when the paper should have left the paper-
411
ejection sensor.
417 The paper-ejection sensor was ON at the start of operation.
431 Paper-ejection error (error occurred during recovery movement)

Error type A10 [AF original feed error]


Panel display
Reset method Turn the AF original detection sensor OFF, and reset the jam.
Error point Error conditions
102 Original-registration-sensor remaining jam
103 Original-IN-sensor remaining jam
104 Original-OUT-sensor remaining jam
105 Original-registration-sensor non-arrival jam
106 Original-IN-sensor non-arrival jam
107 Original-OUT-sensor non-arrival jam
109 An original feed error occurred, due to opening the AF.
162 No original in AF during AF master making.

[17-21]

You might also like