Scribd
Upload
73 views4 pages

G-Code 3018 Kal

The document contains instructions for probing and positioning commands for a CNC machine. It probes at Z-45 and positions to Z1 for probing. It then sets the coordinate system to absolute and positions the Z axis to 0. The document also lists many of the machine parameters stored as variables with a $ prefix, such as maximum travel distances, acceleration rates, and step pulse times.

Uploaded by

Ahmet Özbey
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
73 views4 pages

G-Code 3018 Kal

The document contains instructions for probing and positioning commands for a CNC machine. It probes at Z-45 and positions to Z1 for probing. It then sets the coordinate system to absolute and positions the Z axis to 0. The document also lists many of the machine parameters stored as variables with a $ prefix, such as maximum travel distances, acceleration rates, and step pulse times.

Uploaded by

Ahmet Özbey
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Original Setting CNC 3018 ProVer

Probe Command:
G21G91G38.2Z-45F100; G0Z1; G38.2Z-2F10

G21 Programming in millimeters (mm)


G91: Relative Koordinatenangaben im aktuellen Koordinatensystem
G38.2 tastet auf ein Ziel zu und stoppt bei Kontakt und signalisiert einen Fehler,
wenn es die Zielposition erreicht, ohne die Sonde auszulösen.
G00 Rapid positioning für Z1

Safe position commands:


G21G90; G53G0Z0

G21 Programming in millimeters (mm)


G90 Absolute programming
G53 Machine coordinate system
G00 Rapid positioning Z-1.5

----------------------------------
[CTRL+X] < Grbl 1.1f ['$' for help]
[MSG:'$H'|'$X' to unlock]

$$ < $0=10
$1=25
$2=0
$3=2
$4=0
$5=0
$6=0
$10=3
$11=0.010
$12=0.002
$13=0
$20=0
$21=1
$22=1
$23=3
$24=25.000
$25=500.000
$26=250
$27=1.000
$30=10000

$31=0
$32=0
$100=800.000---> X kalibriert auf 792.079 <-----X------>
$101=800.000---> Y kalibriert auf 793.079 V - /\ = Y
$102=800.000---> Z kalibriert auf 792.079 Z = Spindel

$110=2000.000
$111=2000.000
$112=600.000

$120=10.000
$121=10.000
$122=10.000

$130=260.000
$131=158.000
$132=34.000
ok

Erklärung der $Code (nicht direkt für 3018)


-------------------------------------------
Grbl 1.1f [‘$’ for help]
>>> $$
$0 = 10 (Step pulse time, microseconds)
$1 = 25 (Step idle delay, milliseconds)
$2 = 0 (Step pulse invert, mask)
$3 = 5 (Step direction invert, mask)
$4 = 0 (Invert step enable pin, boolean)
$5 = 0 (Invert limit pins, boolean)
$6 = 0 (Invert probe pin, boolean)
$10 = 3 (Status report options, mask)
$11 = 0.010 (Junction deviation, millimeters)
$12 = 0.002 (Arc tolerance, millimeters)
$13 = 0 (Report in inches, boolean)
$20 = 0 (Soft limits enable, boolean)
$21 = 0 (Hard limits enable, boolean)
$22 = 0 (Homing cycle enable, boolean)
$23 = 0 (Homing direction invert, mask)
$24 = 25.000 (Homing locate feed rate, mm/min)
$25 = 500.000 (Homing search seek rate, mm/min)
$26 = 250 (Homing switch debounce delay, milliseconds)
$27 = 1.000 (Homing switch pull-off distance, millimeters)
$30 = 1000 (Maximum spindle speed, RPM)
$31 = 5 (Minimum spindle speed, RPM)
$32 = 0 (Laser-mode enable, boolean)
$100 = 800.000 (X-axis travel resolution, step/mm)
$101 = 800.000 (Y-axis travel resolution, step/mm)
$102 = 800.000 (Z-axis travel resolution, step/mm)

$110 = 2500.000 (X-axis maximum rate, mm/min)


$111 = 2000.000 (Y-axis maximum rate, mm/min)
$112 = 1500.000 (Z-axis maximum rate, mm/min)
$120 = 45.000 (X-axis acceleration, mm/sec^2)
$121 = 45.000 (Y-axis acceleration, mm/sec^2)
$122 = 48.000 (Z-axis acceleration, mm/sec^2)

$130 = 300.000 (X-axis maximum travel, millimeters)


$131 = 180.000 (Y-axis maximum travel, millimeters)
$132 = 44.000 (Z-axis maximum travel, millimeters)

-----------------------------------------------------------
Grbl 1.1f ['$' for help]
>>> $$
$0 = 10 (Step pulse time, microseconds)
$1 = 25 (Step idle delay, milliseconds)
$2 = 0 (Step pulse invert, mask)
$3 = 6 (Step direction invert, mask)
$4 = 0 (Invert step enable pin, boolean)
$5 = 0 (Invert limit pins, boolean)
$6 = 0 (Invert probe pin, boolean)
$10 = 3 (Status report options, mask)
$11 = 0.010 (Junction deviation, millimeters)
$12 = 0.002 (Arc tolerance, millimeters)
$13 = 0 (Report in inches, boolean)
$20 = 0 (Soft limits enable, boolean)
$21 = 0 (Hard limits enable, boolean)
$22 = 0 (Homing cycle enable, boolean)
$23 = 0 (Homing direction invert, mask)
$24 = 25.000 (Homing locate feed rate, mm/min)
$25 = 500.000 (Homing search seek rate, mm/min)
$26 = 250 (Homing switch debounce delay, milliseconds)
$27 = 1.000 (Homing switch pull-off distance, millimeters)
$30 = 5000 (Maximum spindle speed, RPM)
$31 = 0 Minimum spindle speed, RPM)
$32 = 0 Laser-mode enable, boolean)
$100 = 800.000 (X-axis travel resolution, step/mm)
$101 = 800.000 (Y-axis travel resolution, step/mm)
$102 = 800.000 (Z-axis travel resolution, step/mm)
$110 = 800.000 (X-axis maximum rate, mm/min)
$111 = 800.000 (Y-axis maximum rate, mm/min)
$112 = 800.000 (Z-axis maximum rate, mm/min)
$120 = 10.000 (X-axis acceleration, mm/sec^2)
$121 = 10.000 (Y-axis acceleration, mm/sec^2)
$122 = 10.000 (Z-axis acceleration, mm/sec^2)
$130 = 200.000 (X-axis maximum travel, millimeters)
$131 = 200.000 (Y-axis maximum travel, millimeters)
$132 = 200.000 (Z-axis maximum travel, millimeters)
ok
>>> $G
[GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0 S0]
ok

You might also like