High Tensile Stock List

High Tensile
Stock List 2011

Hobson Engineering Co. Pty. Ltd
A.B.N. 38 000 289 958
Quality Fasteners Since 1935
Sydney Brisbane Melbourne Perth

10 Clay Place 62 Murdoch Circuit Unit 1 155 Abbotts Road 133 Beringarra Ave
Eastern Creek NSW 2766 Acacia Ridge Qld 4110 Dandenong South Vic 3175 Malaga WA 6090
Ph: (02) 8818 0222 Ph: (07) 3273 0777 Ph: (03) 9797 3333 Ph: (08) 9241 9888
Fax: (02) 9620 1850 Fax: (07) 3711 4551 Fax: (03) 9799 3081 Fax: (08) 9248 8806
email: [email protected] email: [email protected] email: [email protected] email: [email protected]
Tasmania Agent www.hobson.com.au

R.M. Daniels & Co P/L
29 Mornington Road
Mornington Tas 7018
Ph: (03) 6244 7455
Fax: (03) 6244 7317
Published by Hobson Engineering Co. Pty. Ltd.

P.O. Box 320
Horsley Park N.S.W. 2175
Look out for other released Hobson Publications.
All rights reserved. Hobson Engineering Co. Pty. Ltd. is the owner of the copyright subsisting in this publication. Other than permitted by
the Copyright Act, no part of this publication can be reproduced, copied or transmitted, in any form or by any means (electric, mechanical,
photocopying, recording, storage in a retrieval system or otherwise), without the prior written consent of Hobson Engineering Co. Pty. Ltd.
Hobson Engineering Co. Pty. Ltd. will vigorously pursue any breach of its copyright.
This publication is distributed on the basis and understanding that the publisher is not responsible for the results of any actions taken on the
basis of information in this publication, nor for any error in or omission from this publication The publisher expressly disclaims all and any liability
and responsibility to any person, whether a reader of this publication or not, in respect of anything, and the consequences of anything, done
or omitted to be done by any such person in reliance, whether wholly or partially, upon the whole or any part of the contents of this publication.
Without limiting the generality of the foregoing the publisher accepts no liability for any loss or damage either direct or consequential arising out
of or in relation to the use or application of the information or products referred to herein.
Since 1935 ...because quality matters April 2011

Index
Sampsonrod® [Allthread] 2
Starter Bar (L-Bolt) 5
Purlin Assemblies 6
Class 8 Hex Nuts 6

AS1252 Hex Nuts 7
Class 10 Hex Nuts 8
Grade 2, 5 & 8 Hex Nuts 10
Washers 14
AS1252 Structural 18
Class 8.8 Hex Set Screws 24

Class 8.8 Hex Bolts & Nuts 27
Grade 5 Hex Bolts & Nuts 36
Grade 8 Hex Bolts & Nuts 38
Class 10.9 Hex Bolts 56
Plow Bolts & Nuts 62
Technical Thread Table 64
April 2011 Quality Fasteners Since 1935 1

Sampsonrod™ Metric
Hot Dip Galvanise
Zinc Yellow Passivate
Plain
METRIC SAMPSONROD™ 1MTR
CLASS 8.8 DIN975
Part Size Pack Pack Wgt Stock

(Kg) HDG PLN ZYP
AS88PCM061000 M6 1 0.22 P
AS88PCM081000 M8 1 0.31 P
AS88?CM101000 M10 20 9.80 P P P
AS88?CM121000 M12 10 7.10 P P P
AS88PCM141000 M14 1 0.98 P
AS88?CM161000 M16 10 13.10 P P P
AS88PCM181000 M18 1 1.90 P
AS88?CM201000 M20 5 10.25 P P P
AS88PCM221000 M22 1 2.50 P
AS88?CM241000 M24 5 14.75 P P P
AS88?CM271000 M27 1 3.80 P P
AS88?CM301000 M30 1 4.68 P P
AS88?CM331000 M33 1 5.70 P P
AS88?CM361000 M36 1 6.82 P P
AS88PCM391000 M39 1 8.00 P
AS88PCM421000 M42 1 9.30 P
AS88PCM481000 M48 1 12.20 P
AS88PCM521000 M52 1 15.00 P
METRIC SAMPSONROD™ 3MTR

CLASS 8.8 DIN975

(Kg) HDG PLN
AS88PCM103000 M10 10 14.60 P
AS88?CM123000 M12 5 10.70 P P
AS88?CM163000 M16 5 19.70 P P
AS88?CM203000 M20 2 12.44 P P
AS88?CM243000 M24 1 8.94 P P
AS88?CM303000 M30 1 14.11 P P
AS88?CM363000 M36 1 20.62 P P
? = G: Hot Dip Galvanise (HDG) Z: Zinc Plate (Z/P) Y: Zinc Yellow Passivate (ZYP) P: Plain (PLN)
2 Quality Fasteners Since 1935 April 2011

Sampsonrod™ UNC / UN8
Plain
METRIC FINE PITCH SAMPSONROD™ 1MTR

CLASS 8.8 DIN975
Part Size Pitch Pack Pack Wgt Stock

(Kg) HDG PLN
AS88PFM101000 M10 1.25 1 0.51 P
AS88PFM121000 M12 1.25 1 0.75 P
AS88PFM161000 M16 1.50 1 1.36 P
AS88?FM301000 M30 2.00 1 4.68 P P
AS88?FM361000 M36 3.00 1 6.82 P P
UNC SAMPSONROD™ 3FT

GRADE 5 IFI136C

(Kg) PLN
ASG5PC0250914 1/4″ 20 3.40 P
ASG5PC0310914 5/16″ 20 5.40 P
ASG5PC0370914 3/8″ 20 8.00 P
ASG5PC0430914 7/16″ 10 5.40 P
ASG5PC0500914 1/2″ 10 7.30 P
ASG5PC0560914 9/16″ 10 8.90 P
ASG5PC0620914 5/8″ 10 11.55 P
ASG5PC0750914 3/4″ 5 8.45 P
ASG5PC0870914 7/8″ 5 11.60 P
ASG5PC1000914 1″ 5 15.25 P
ASG5PC1120914 1 1/8″ 1 3.87 P
ASG5PC1250914 1 1/4″ 1 4.82 P
ASG5PC1500914 1 1/2″ 1 6.97 P
UN8 SAMPSONROD™ 3FT

GRADE 5 IFI136C

(Kg) PLN
ASG5PU1120914 1 1/8″ 1 3.92 P
ASG5PU1250914 1 1/4″ 1 4.93 P
ASG5PU1370914 1 3/8″ 1 6.04 P
ASG5PU1500914 1 1/2″ 1 7.28 P
April 2011 Quality Fasteners Since 1935

3
Sampsonrod™ UNF / BSF / BSW
Plain
UNF SAMPSONROD™ 3FT

GRADE 5 IFI136C
Part Size TPI Pack Pack Wgt Stock

(Kg) PLN
ASG5PF0500914 1/2″ 20 1 0.78 P
ASG5PF0620914 5/8″ 18 1 1.24 P
ASG5PF0750914 3/4″ 16 1 1.80 P
ASG5PF0870914 7/8″ 14 1 2.48 P
ASG5PF1000914 1″ 12 1 3.19 P
ASG5PF1000914F 1″ 14 1 3.19 P
ASG5PF1120914 1 1/8″ 12 1 4.15 P
ASG5PF1250914 1 1/4″ 12 1 4.98 P
ASG5PF1500914 1 1/2″ 12 1 7.59 P
BSF SAMPSONROD™ 3FT

GRADE 5 AS3501(THREAD)

(Kg) PLN
ASG5PS0500914 1/2″ 16 1 0.75 P
ASG5PS0620914 5/8″ 14 1 1.19 P
ASG5PS0750914 3/4″ 12 1 1.75 P
ASG5PS0870914 7/8″ 11 1 2.41 P
ASG5PS1000914 1″ 10 1 3.18 P
ASG5PS1120914 1 1/8″ 9 1 4.03 P
ASG5PS1250914 1 1/4″ 9 1 5.04 P
ASG5PS1500914 1 1/2″ 8 1 7.32 P
BSW SAMPSONROD™ 3FT

GRADE 5 AS3501(THREAD)

(Kg) PLN
ASG5PW0500914 1/2″ 12 1 0.71 P

Hobrod™ Metric / UNC
Plain
METRIC HOBROD™ 1mtr

CLASS 10.9 DIN975

(Kg) PLN
AS10PCM061000 M6 1 0.17 P
AS10PCM081000 M8 1 0.31 P
AS10PCM101000 M10 20 9.80 P
AS10PCM121000 M12 10 7.10 P
AS10PCM161000 M16 10 13.10 P
AS10PCM201000 M20 5 10.35 P
AS10PCM241000 M24 5 14.98 P
UNC HOBROD™ 3FT

GRADE 8 IFI136C

(Kg) PLN
ASG8PC0620914 5/8″ 10 11.55 P
ASG8PC0750914 3/4″ 10 16.90 P
ASG8PC0870914 7/8″ 5 11.60 P
ASG8PC1000914 1″ 5 15.25 P
ASG8PC1120914 1 1/8″ 2 7.74 P
ASG8PC1250914 1 1/4″ 2 9.64 P
STARTER BAR ( L BOLT )

CLASS 8.8 HOBSON STANDARD
Part A L D T Pack Pack Wgt Stock

(mm) (mm) (mm) (Kg) Z/P
LB88ZCM120169 M12 169 44 75 50 7.50 P
LB88ZCM160292 M16 292 67 75 25 11.75 P
LB88ZCM200365 M20 365 65 100 10 8.90 P
LB88ZCM240438 M24 438 63 100 5 7.45 P
LB88ZCM300585 M30 585 90 100 2 6.36 P

5
Purlin Assembly / Class 8 Nuts
Hot Dip Galvanise
Plain
PURLIN HEX BOLT, NUT & 2 WASHER KIT
CLASS 8.8 / CLASS 8 HOBSON STANDARD (ASSEMBLED)
Pack Wgt
Part Size Length Pack Pallet Stock
(Kg)
(mm) Z/P
KBHHTZCM160030 M16 30 100 14.10 4,800 P
KBHHTZCM160040 M16 40 100 15.80 4,800 P
FASCIA HEX BOLT & NUT KIT

Pack Wgt
(Kg)
(mm) HDG
KBAHTGCM100025 M10 25 200 7.37 16,000 P
KBAHTGCM120030 M12 30 150 9.00 12,000 P
PURLIN HEX FLANGE BOLT & NUT KIT

Pack Wgt
(Kg)
(mm) Z/P
KBFHTZCM120030 M12 30 150 10.92 7,200 P
METRIC HEX NUT

CLASS 8 AS1112.1
Pack Wgt
Part Size Carton Pack Stock
(Kg)
HDG Z/P PLN
NH08ZCM04 M4 12000 1000 1.25 P
NH08ZCM05 M5 12000 1000 1.50 P
NH08?CM06 M6 6000 1000 2.00 P P
NH08?CM08 M8 3000 500 2.50 P P
NH08?CM10 M10 1200 200 1.85 P P
NH08?CM12 M12 1200 200 3.09 P P
NH08ZCM14 M14 100 25 0.58 P
NH08?CM16 M16 200 200 7.00 P P P
NH08ZCM18 M18 100 25 1.20 P
NH08ZCM20 M20 100 100 6.70 P
NH08?CM24 M24 100 100 11.28 P P
METRIC HEX LOCK NUT

CLASS 8 AS1112.4
Pack Wgt
Part Size Pack Stock
(Kg)
HDG
NL08GCM12 M12 100 0.93 P
NL08GCM16 M16 100 2.14 P

Nylon Insert Nut / AS1252
Zinc Yellow Passivate Nylon Insert Nuts
Hot Dip Galvanise and Plain AS1252 Structural Nuts
METRIC NYLON INSERT HEX NUT

CLASS 8 DIN985
Pack Wgt
(Kg)
ZYP
NN08YCM05 M5 200 0.28 P
NN08YCM06 M6 200 0.48 P
NN08YCM08 M8 200 1.02 P
NN08YCM10 M10 200 2.12 P
NN08YCM12 M12 100 1.72 P
NN08YCM14 M14 100 2.60 P
NN08YCM16 M16 100 3.40 P
NN08YCM18 M18 100 4.50 P
NN08YCM20 M20 50 3.25 P
METRIC FINE PITCH NYLON INSERT HEX NUT

CLASS 8 DIN985
Pack Wgt
Part Size Pitch Pack Stock
(Kg)
ZYP
NN08YFM08 M8 1.00 200 1.02 P
NN08YFM10 M10 1.25 200 2.12 P
NN08YFM10F M10 1.00 200 2.12 P
NN08YFM12 M12 1.50 100 1.72 P
NN08YFM12F M12 1.25 100 1.72 P
NN08YFM16 M16 1.50 100 3.40 P
NN08YFM20 M20 1.50 50 3.25 P
STRUCTURAL HEX NUTS

CLASS 8 AS1252

(Kg) HDG PLN
NHST?CM12 M12 500 12.25 P P
NHST?CM16 M16 450 24.98 P P
NHST?CM20 M20 250 22.50 P P
NHST?CM24 M24 100 19.20 P P
NHST?CM30 M30 50 18.50 P P
NHST?CM36 M36 25 15.00 P P

7
Class 10 Hex / Locking Nuts
Zinc Plate
Plain
METRIC HEX NUT

CLASS 10 DIN934

(Kg) PLN
NH10PCM06 M6 1000 2.00 P
NH10PCM08 M8 500 2.50 P
NH10PCM10 M10 200 1.85 P
NH10PCM12 M12 200 3.09 P
NH10PCM16 M16 200 7.00 P
NH10PCM20 M20 100 6.70 P
NH10PCM24 M24 100 11.25 P
NH10PCM30 M30 50 13.25 P
NH10PCM36 M36 25 9.65 P
NH10PCM42 M42 20 12.05 P
NH10PCM48 M48 15 13.90 P
NH10PCM56 M56 1 1.34 P
NH10PCM64 M64 1 2.48 P
NH10PCM72 M72 1 3.00 P
METRIC HCL CONE LOCKING HEX NUT

CLASS 10 DIN980

(Kg) Z/P
NC10ZCM06 M6 200 0.52 P
NC10ZCM08 M8 200 1.13 P
NC10ZCM10 M10 200 1.41 P
NC10ZCM12 M12 100 1.75 P
NC10ZCM14 M14 100 2.75 P
NC10ZCM16 M16 100 3.64 P
NC10ZCM20 M20 50 3.74 P
NC10ZCM24 M24 25 3.01 P
METRIC FINE HCL CONE LOCKING HEX NUT

CLASS 10 DIN980
Part Size Pitch Pack Pack Wgt Stock

(Kg) Z/P
NC10ZFM10 M10 1.25 200 2.12 P
NC10ZFM12 M12 1.50 100 1.72 P
NC10ZFM16 M16 1.50 100 3.40 P
NC10ZFM20 M20 1.50 50 3.25 P

Nylon Insert / Flange Nuts
METRIC NYLON INSERT HEX NUT

CLASS 10 DIN985

(Kg) ZYP
NN10YCM10 M10 200 2.12 P
NN10YCM12 M12 100 1.72 P
NN10YCM16 M16 100 3.40 P
NN10YCM20 M20 50 3.25 P
METRIC NYLON INSERT FLANGE HEX NUT

CLASS 10 DIN6926

(Kg) ZYP
NF10YNM12 M12 100 4.00 P
NF10YNM14 M14 100 4.20 P
NF10YNM16 M16 100 4.70 P
NF10YNM20 M20 50 2.60 P

9
Grade 5 & 8 Hex Nuts
Zinc Plate
Plain
UNC HEX NUT

GRADE 8 AS2465
Pack Wgt
(Kg)
Z/P PLN
NHG8?C025 1/4″ 1000 3.25 P P
NHG8?C031 5/16″ 1000 4.80 P P
NHG8?C037 3/8″ 500 3.50 P P
NHG8?C043 7/16″ 500 6.40 P P
NHG8?C050 1/2″ 200 3.32 P P
NHG8?C056 9/16″ 75 1.97 P P
NHG8?C062 5/8″ 75 2.48 P P
NHG8?C075 3/4″ 75 3.90 P P
NHG8?C087 7/8″ 50 4.15 P P
NHG8?C100 1″ 50 6.30 P P
NHG8PC112 1 1/8″ 25 4.45 P
NHG8PC125 1 1/4″ 25 6.00 P
NHG8PC150 1 1/2″ 15 6.30 P
UNF HEX NUT

GRADE 8 AS2465
Pack Wgt
(Kg)
Z/P PLN
NHG8?F025 1/4″ 1000 3.41 P P
NHG8?F031 5/16″ 1000 5.04 P P
NHG8?F037 3/8″ 500 3.68 P P
NHG8?F043 7/16″ 500 6.72 P P
NHG8?F050 1/2″ 200 3.32 P P
NHG8ZF056 9/16″ 75 1.97 P
NHG8?F062 5/8″ 75 2.48 P P
NHG8?F075 3/4″ 75 3.90 P P
NHG8?F087 7/8″ 50 4.36 P P
NHG8?F100F 1″-14 50 6.62 P P

Grade 2, 5 & 8 Nylon Insert
Zinc Plate
UNC NYLON INSERT HEX NUT

GRADE 2, 5 & 8 IFI100NE
Pack Wgt
Part Size Pack Z/P Stock
(Kg)
Grade 2 Grade 5 Grade 8
NNG5ZC025 1/4″ 200 0.72 P
NNG5ZC031 5/16″ 200 1.02 P
NNG5ZC037 3/8″ 200 1.58 P
NNG5ZC043 7/16″ 200 1.90 P
NNG?ZC050 1/2″ 100 2.02 P P
NNG5ZC056 9/16″ 100 2.83 P
NNG?ZC062 5/8″ 100 3.96 P P
NNG?ZC075 3/4″ 50 2.74 P P
NNG?ZC087 7/8″ 50 4.29 P P
NNG?ZC100 1″ 25 3.08 P P
NNG2ZC112 1 1/8″ 25 4.65 P
NNG2ZC125 1 1/4″ 10 2.63 P
NNG2ZC137 1 3/8″ 10 3.60 P
NNG2ZC150 1 1/2″ 10 4.53 P
UNF NYLON INSERT HEX NUT

GRADE 5 & 8 IFI100NE
Pack Wgt
Part Size Pack Z/P Stock
(Kg)
Grade 5 Grade 8
NNG5ZF025 1/4″ 200 0.72 P
NNG5ZF031 5/16″ 200 1.02 P
NNG5ZF037 3/8″ 200 1.58 P
NNG5ZF043 7/16″ 200 1.90 P
NNG?ZF050 1/2″ 100 2.02 P P
NNG5ZF056 9/16″ 100 2.83 P
NNG?ZF062 5/8″ 100 3.96 P P
NNG?ZF075 3/4″ 50 2.74 P P
NNG?ZF087 7/8″ 50 4.29 P P
NNG?ZF100F 1″-14 25 3.08 P P
? = 2: Grade 2 5: Grade 5 8: Grade 8

11
TONE® Electric
Structural Bolting
Torque Control Wrench
made easy and
accurate with the:
Hobson
Structural Assembly.
Squirter® Washer
Direct Tension Indicator. Part: XT-STC7TE
TONE®
Electric Torque Control Wrench.
Featuring:
P 2 x Safety Reaction Arms
P L-Shape Arm + Long Bar Arm 230mm
P Light Weight
P Non Impacting
P Low Noise
P Automatic Shut-off at Preset Torque
Part: XT-STC11TE
Managing maximum
force – even in
extreme conditions.
SCHNORR® is an international leader in engineering and

manufacturing of safety washers and disc springs for the auto-
motive or aerospace industry and machine constructions.
Original SCHNORR® safety washers:

• high resistance to vibration
• patented technology
• extensive range
Original SCHNORR® disc springs:

• manifold applications
• optimal price/performance ratio
• tailor-made solutions
Sampson™ Washers
Plain
Zinc Plate
SAMPSON™ WASHER
38-45HRC HOBSON STANDARD
Part Size OD ID Thk Pack Pack Wgt

(mm) (mm) (mm) (Kg) PLN
WR43PM08 M8 18.0 8.5 2.3 200 0.64 P
WR43PM10 M10 22.0 10.5 3.0 100 0.69 P
WR43PM12 M12 26.0 13.0 3.2 100 0.90 P
WR43PM16 M16 32.0 17.0 4.5 100 1.83 P
WR43PM20 M20 40.0 21.0 4.5 100 2.89 P
WR43PM22 M22 44.0 23.0 6.0 100 4.68 P
WR43PM24 M24 48.0 25.0 6.0 100 5.59 P
WR43PM27 M27 56.0 28.0 8.0 100 10.44 P
WR43PM30 M30 60.0 32.0 8.0 100 11.43 P
WR43PM36 M36 72.0 37.5 8.0 25 4.19 P
WR43PM42 M42 85.0 43.5 8.0 25 5.92 P
WR43PM48 M48 98.0 49.5 8.0 25 7.94 P
WR43PM52 M52 100.0 53.2 10.0 20 7.95 P
WR43PM56 M56 105.0 62.0 10.0 10 3.98 P
WR43PM64 M64 115.0 70.0 10.0 5 2.31 P
ZINC PLATE SAMPSON™ WASHER

38-45HRC ASTM F436M TYPE 1
Part Size OD ID Thk Pack Pack Wgt

WR43ZM06 M6 13.0 6.7 1.5 200 0.34 P
WR43ZM08 M8 18.0 8.9 1.9 200 0.92 P
WR43ZM10 M10 20.0 10.9 1.9 200 0.95 P
WR43ZM12 M12 27.0 14.0 3.8 200 3.52 P
WR43ZM14 M14 30.0 16.0 3.8 100 2.13 P
WR43ZM16 M16 34.0 18.0 3.8 100 2.73 P
WR43ZM20 M20 42.0 22.0 3.8 50 2.08 P
WR43ZM24 M24 50.0 26.0 3.8 50 2.96 P
WR43ZM30 M30 60.0 33.0 3.8 10 0.82 P
WR43ZM36 M36 72.0 39.0 3.8 10 1.19 P

Sampson™ / Panel Washers
F436 SAMPSON™ WASHER

38-45HRC ASTM F436
Part Size OD ID Thk Pack Pack Wgt Price

(mm) (mm) (mm) (Kg) ZYP
WR43Y025 1/4″ 15.88 7.14 1.7 200 0.37 P
WR43Y031 5/16″ 17.48 8.74 1.7 200 0.42 P
WR43Y037 3/8″ 20.65 10.31 1.7 200 0.59 P
WR43Y043 7/16″ 23.42 11.91 1.7 200 0.75 P
WR43Y050 1/2″ 27.00 13.49 3.5 200 2.11 P
WR43Y056 9/16″ 29.50 15.83 3.5 100 1.33 P
WR43Y062 5/8″ 33.35 17.48 3.8 100 1.70 P
WR43Y075 3/4″ 37.31 20.65 4.0 50 1.02 P
WR43Y087 7/8″ 44.45 23.83 4.0 50 1.56 P
WR43Y100 1″ 50.80 28.57 4.0 50 1.95 P
WR43Y112 1 1/8″ 57.15 31.75 4.0 20 1.00 P
WR43Y125 1 1/4″ 63.50 34.92 4.0 10 0.62 P
WR43Y137 1 3/8″ 69.85 38.10 4.0 10 0.76 P
WR43Y150 1 1/2″ 76.20 41.27 4.0 10 0.92 P
WR43Y175 1 3/4″ 85.72 47.62 5.2 10 1.64 P
WR43Y200 2″ 95.25 53.98 5.2 10 1.99 P
WR43Y225 2 1/4″ 101.60 60.33 7.4 10 2.73 P
WR43Y250 2 1/2″ 114.30 66.67 7.4 10 3.52 P
WR43Y300 3″ 139.70 79.38 7.4 10 5.40 P
CONCRETE PANEL WASHER

AS1237.1-2002 (TABLE 3)
Part Size OD ID Thk Pack Pack Wgt Stock

WPMSZM20 M20 60.0 22.0 4.0 25 1.94 P
M20 Class 8.8 Set Screws / Panel Bolts on page 32

15
AS1252 Structural
Hot Dip Galvanise
Mechanical Galvanise
Plain
STRUCTURAL WASHER
35-45HRC AS1252
Part Size OD ID Thk Pack Pack Wgt Price

(mm) (mm) (mm) (Kg) HDG PLN
WRST?M12 M12 25.7 14.0 3.1 1000 10.06 P P
WRST?M16 M16 32.4 18.0 3.1 800 12.27 P P
WRST?M20 M20 37.4 21.0 3.1 500 10.47 P P
WRST?M22 M22 42.4 24.0 3.4 350 8.06 P P
WRST?M24 M24 48.4 26.0 3.4 350 15.75 P P
WRSTGM27 M27 54.1 30.0 3.4 420 19.86 P
WRST?M30 M30 58.1 33.0 3.4 250 13.36 P P
WRST?M36 M36 70.1 39.0 3.4 200 22.00 P P
SQUIRTER® DTI (DIRECT TENSION INDICATOR) WASHER

ASTM F959M / MECHANICAL GALVANISE
Part Size OD ID Thk No. of Keg Keg Wgt Price

Bumps
(mm) (mm) (mm) (Kg) MGALV
WDSTGM16 M16 36.0 17.0 3.4 4 1250 22.7 P
WDSTGM20 M20 46.0 21.0 3.8 5 750 27.2 P
WDSTGM24 M24 55.0 25.0 4.4 5 450 27.2 P
WDSTGM30 M30 68.0 32.0 4.4 7 250 27.2 P
WDSTGM36 M36 81.0 38.0 5.0 8 175 27.2 P
WDSTG050 1/2″ 34.9 13.4 3.0 4 1750 23.8 P
WDSTG087 7/8″ 50.8 23.4 4.0 5 650 27.2 P
LOAD INDICATOR WASHER

ASTM F959M / MECHANICAL GALVANISE
Part Size OD ID Thk No. of Keg Keg Wgt Price

Bumps
(mm) (mm) (mm) (Kg) MGALV
WISTGM16 M16 36.0 17.0 3.4 4 1250 22.7 P
WISTGM20 M20 46.0 21.0 3.8 5 750 27.2 P
WISTGM24 M24 55.0 25.0 4.4 5 450 27.2 P
FEELER GAUGE

(Kg)
XGF013 0.13 10 0.01 P

Squirter® DTIs (Direct Tension Indicator)
Designed for AS1252 Structural Bolting.
Features
P Manufactured to ASTM F959M.
Conforms to AS4100-1990 15.4.1 (b)

P Direct-tensioning indication device.
Not Tensioned
P Lot trace number on each washer.
Test Certificates available online

Tensioned P www.hobson.com.au.
Visual tension indication by
P Orange Silicone.
Enables efficient & accurate installation
P of AS1252 structural assemblies.
SQUIRTER® DTIs (Direct Tension Indicator) are DTIs with a flexible silicone embedded in the depressions under the
bumps. To use them, simply ... Tighten the bolt until the calibrated amount of orange silicone appears from under the
DTIs squirt locations, then stop tightening. That’s all there is to it.
Now you can see when the bolt assembly

is tensioned correctly.
Easier & Better than Turn-of Nut Saves Time

You don’t have to remember to stop turning at 1/3rd, 1/2, or Enables correct tensioning as fast as the wrench can be
2/3rds turn. No match marking necessary. moved to the next bolt, because the operator can see when
to stop.
Safe for Inspectors

Once calibrated, inspectors can easily see the orange squirts,
they don’t have to climb to all the connections or carry around
a torque wrench to know the connection has been completed. Since 1935
And instead of sampling only some of the DTIs with a feeler
gage, squirters allow virtually 100% inspection.
... because quality matters
SQUIRTER® DTIs
the best way to bolt!
www.hobson.com.au
AS1252 Structural
Hot Dip Galvanise
STRUCTURAL ASSEMBLIES
AS1252 (1983 DIMENSIONS & 1996 MECHANICAL PROPERTIES)
Part Size Length Thread Pack Pack Wgt Stock

(mm) (mm) (Kg) HDG
KBHSTGCM120030 M12 30 20 200 13.52 P
KBHSTGCM120035 M12 35 25 200 14.52 P
KBHSTGCM120040 M12 40 30 150 15.32 P
KBHSTGCM120045 M12 45 30 150 12.24 P
KBHSTGCM120050 M12 50 30 150 12.84 P
KBHSTGCM120060 M12 60 30 150 13.89 P
KBHSTGCM120065 M12 65 30 150 13.92 P
KBHSTGCM120070 M12 70 30 150 13.95 P
KBHSTGCM120075 M12 75 30 150 13.99 P
KBHSTGCM120080 M12 80 30 150 14.01 P
KBHSTGCM120090 M12 90 30 100 13.89 P
KBHSTGCM120100 M12 100 30 100 14.25 P
KBHSTGCM120120 M12 120 36 75 12.82 P
KBHSTGCM120150 M12 150 36 75 15.02 P
KBHSTGCM120180 M12 180 36 50 12.02 P
KBHSTGCM120200 M12 200 36 50 13.05 P

AS1252 Structural
Hot Dip Galvanise

(mm) (mm) (Kg) HDG
KBHSTGCM160040 M16 40 26 100 18.45 P
KBHSTGCM160045 M16 45 31 100 19.00 P
KBHSTGCM160050 M16 50 36 100 19.00 P
KBHSTGCM160055 M16 55 38 100 20.00 P
KBHSTGCM160060 M16 60 38 100 21.45 P
KBHSTGCM160065 M16 65 38 75 15.75 P
KBHSTGCM160070 M16 70 38 75 16.50 P
KBHSTGCM160075 M16 75 38 75 17.25 P
KBHSTGCM160080 M16 80 38 75 18.00 P
KBHSTGCM160090 M16 90 38 75 19.50 P
KBHSTGCM160100 M16 100 38 75 20.25 P
KBHSTGCM160110 M16 110 38 50 14.85 P
KBHSTGCM160120 M16 120 38 50 16.20 P
KBHSTGCM160130 M16 130 44 50 16.33 P
KBHSTGCM160140 M16 140 44 50 17.01 P
KBHSTGCM160150 M16 150 44 50 17.85 P
KBHSTGCM160160 M16 160 44 50 18.08 P
KBHSTGCM160170 M16 170 44 50 19.14 P
KBHSTGCM160180 M16 180 44 35 19.68 P
KBHSTGCM160190 M16 190 44 35 13.55 P
KBHSTGCM160200 M16 200 44 35 14.56 P
KBHSTGCM160220 M16 220 57 35 15.61 P
KBHSTGCM160240 M16 240 100 35 16.24 P
KBHSTGCM160250 M16 250 100 35 16.80 P
KBHSTGCM160270 M16 270 100 35 17.85 P
KBHSTGCM160300 M16 300 100 25 13.63 P
KBHSTGCM160350 M16 350 120 1 0.66 P
KBHSTGCM160400 M16 400 120 1 0.75 P
KBHSTGCM160500 M16 500 120 1 0.94 P
KBHSTGCM160600 M16 600 120 1 1.13 P

19
AS1252 Structural
Hot Dip Galvanise

(mm) (mm) (Kg) HDG
KBHSTGCM200040 M20 40 23 75 21.75 P
KBHSTGCM200045 M20 45 28 75 22.50 P
KBHSTGCM200050 M20 50 33 50 16.00 P
KBHSTGCM200055 M20 55 38 50 16.08 P
KBHSTGCM200060 M20 60 43 50 16.50 P
KBHSTGCM200065 M20 65 46 50 17.50 P
KBHSTGCM200070 M20 70 46 50 18.00 P
KBHSTGCM200075 M20 75 46 50 18.50 P
KBHSTGCM200080 M20 80 46 50 19.00 P
KBHSTGCM200085 M20 85 46 50 20.00 P
KBHSTGCM200090 M20 90 46 40 15.77 P
KBHSTGCM200100 M20 100 46 40 18.05 P
KBHSTGCM200110 M20 110 46 40 18.80 P
KBHSTGCM200120 M20 120 46 30 14.70 P
KBHSTGCM200130 M20 130 52 30 15.00 P
KBHSTGCM200140 M20 140 52 30 16.20 P
KBHSTGCM200150 M20 150 52 30 16.20 P
KBHSTGCM200160 M20 160 52 30 17.25 P
KBHSTGCM200180 M20 180 52 25 15.63 P
KBHSTGCM200190 M20 190 52 25 15.68 P
KBHSTGCM200200 M20 200 52 25 16.30 P
KBHSTGCM200210 M20 210 65 25 16.88 P
KBHSTGCM200220 M20 220 65 25 17.45 P
KBHSTGCM200240 M20 240 65 20 14.92 P
KBHSTGCM200250 M20 250 100 20 15.32 P
KBHSTGCM200275 M20 275 100 20 16.52 P
KBHSTGCM200300 M20 300 100 15 13.11 P
KBHSTGCM200350 M20 350 120 1 1.05 P
KBHSTGCM200400 M20 400 120 1 1.15 P
KBHSTGCM200500 M20 500 120 1 1.44 P
KBHSTGCM200600 M20 600 120 1 1.74 P

AS1252 Structural
Hot Dip Galvanise

(mm) (mm) (Kg) HDG
KBHSTGCM240050 M24 50 29 30 17.10 P
KBHSTGCM240055 M24 55 34 30 17.70 P
KBHSTGCM240060 M24 60 39 30 18.00 P
KBHSTGCM240065 M24 65 44 30 18.60 P
KBHSTGCM240070 M24 70 49 30 18.90 P
KBHSTGCM240075 M24 75 54 30 19.50 P
KBHSTGCM240080 M24 80 54 30 19.80 P
KBHSTGCM240085 M24 85 54 30 20.00 P
KBHSTGCM240090 M24 90 54 25 17.50 P
KBHSTGCM240100 M24 100 54 25 18.10 P
KBHSTGCM240110 M24 110 54 20 15.40 P
KBHSTGCM240120 M24 120 54 20 16.20 P
KBHSTGCM240130 M24 130 60 20 16.80 P
KBHSTGCM240140 M24 140 60 20 17.60 P
KBHSTGCM240150 M24 150 60 20 18.20 P
KBHSTGCM240160 M24 160 60 20 18.50 P
KBHSTGCM240170 M24 170 60 20 19.60 P
KBHSTGCM240180 M24 180 60 15 14.90 P
KBHSTGCM240200 M24 200 60 15 15.63 P
KBHSTGCM240210 M24 210 73 15 16.35 P
KBHSTGCM240220 M24 220 73 15 17.18 P
KBHSTGCM240230 M24 230 73 15 17.96 P
KBHSTGCM240250 M24 250 73 15 19.52 P
KBHSTGCM240260 M24 260 120 15 19.92 P
KBHSTGCM240280 M24 280 120 15 20.75 P
KBHSTGCM240300 M24 300 120 10 13.70 P
KBHSTGCM240330 M24 330 120 1 1.45 P
KBHSTGCM240350 M24 350 120 1 1.53 P
KBHSTGCM240390 M24 390 120 1 1.69 P
KBHSTGCM240400 M24 400 120 1 1.77 P
KBHSTGCM240415 M24 415 120 1 1.82 P
KBHSTGCM240450 M24 450 120 1 1.95 P
KBHSTGCM240500 M24 500 120 1 2.18 P
KBHSTGCM240550 M24 550 120 1 2.50 P
KBHSTGCM240600 M24 600 120 1 2.72 P

21
AS1252 Structural
Hot Dip Galvanise

(mm) (mm) (Kg) HDG
KBHSTGCM300075 M30 75 50 15 17.40 P
KBHSTGCM300080 M30 80 55 15 17.40 P
KBHSTGCM300085 M30 85 60 15 18.00 P
KBHSTGCM300090 M30 90 65 15 18.45 P
KBHSTGCM300100 M30 100 66 15 19.20 P
KBHSTGCM300110 M30 110 66 10 12.59 P
KBHSTGCM300120 M30 120 66 10 13.09 P
KBHSTGCM300130 M30 130 72 10 14.60 P
KBHSTGCM300140 M30 140 72 10 14.90 P
KBHSTGCM300150 M30 150 72 10 15.40 P
KBHSTGCM300160 M30 160 72 10 15.90 P
KBHSTGCM300170 M30 170 72 10 16.40 P
KBHSTGCM300180 M30 180 72 8 13.60 P
KBHSTGCM300190 M30 190 72 8 14.08 P
KBHSTGCM300200 M30 200 72 8 14.56 P
KBHSTGCM300220 M30 220 85 8 14.56 P
KBHSTGCM300260 M30 260 85 8 16.42 P
KBHSTGCM300280 M30 280 100 8 18.00 P
KBHSTGCM300300 M30 300 100 1 1.82 P
KBHSTGCM300350 M30 350 120 1 2.12 P
KBHSTGCM300400 M30 400 120 1 2.42 P
KBHSTGCM300500 M30 500 120 1 3.03 P

AS1252 Structural
Hot Dip Galvanise

(mm) (mm) (Kg) HDG
KBHSTGCM360090 M36 90 60 8 16.40 P
KBHSTGCM360100 M36 100 70 8 16.88 P
KBHSTGCM360120 M36 120 78 8 18.37 P
KBHSTGCM360130 M36 130 84 8 17.92 P
KBHSTGCM360140 M36 140 84 8 18.56 P
KBHSTGCM360150 M36 150 84 8 19.16 P
KBHSTGCM360160 M36 160 84 5 12.35 P
KBHSTGCM360170 M36 170 84 5 12.75 P
KBHSTGCM360180 M36 180 84 5 13.15 P
KBHSTGCM360190 M36 190 84 5 13.35 P
KBHSTGCM360200 M36 200 84 5 13.60 P
KBHSTGCM360220 M36 220 97 1 2.71 P
KBHSTGCM360240 M36 240 97 1 2.96 P
KBHSTGCM360260 M36 260 97 1 3.20 P
KBHSTGCM360280 M36 280 100 1 3.44 P
KBHSTGCM360300 M36 300 100 1 3.69 P
KBHSTGCM360400 M36 400 120 1 4.92 P
KBHSTGCM360500 M36 500 120 1 6.15 P

23
Hex Set Screw Class 8.8
Zinc Plate
HEX SET SCREW

Class 8.8 AS1110.2
Part Size Length Pack BO Wgt Blk Kit ZP Set ZP Kit

(mm) (Kg)
BS88ZCM050012 M5 12 200 0.58 P
BS88ZCM050016 M5 16 200 0.68 P
BS88ZCM050020 M5 20 200 0.78 P
BS88ZCM050025 M5 25 200 0.97 P
BS88ZCM050030 M5 30 200 1.13 P
BS88ZCM050035 M5 35 200 1.28 P
BS88ZCM050040 M5 40 200 1.44 P
BS88ZCM060012 M6 12 200 0.95 P
BS88ZCM060016 M6 16 200 1.00 * P *
BS88ZCM060020 M6 20 200 1.20 * P *
BS88ZCM060025 M6 25 200 1.40 * P *
BS88ZCM060030 M6 30 200 1.60 P
BS88ZCM060035 M6 35 200 1.80 P
BS88ZCM060040 M6 40 200 2.00 P
BS88ZCM060045 M6 45 200 2.20 P
BS88ZCM060050 M6 50 200 2.50 P
BS88ZCM080012 M8 12 200 1.90 * P *
BS88ZCM080016 M8 16 200 2.10 * P *
BS88ZCM080020 M8 20 200 2.30 * P *
BS88ZCM080025 M8 25 200 2.60 * P *
BS88ZCM080030 M8 30 200 3.00 * P *
BS88ZCM080035 M8 35 200 3.30 P
BS88ZCM080040 M8 40 200 3.60 P
BS88ZCM080045 M8 45 200 4.06 P
BS88ZCM080050 M8 50 200 4.20 P
BS88ZCM080055 M8 55 150 3.51 P
BS88ZCM080060 M8 60 150 3.75 P
BS88ZCM080065 M8 65 150 3.99 P
BS88ZCM080070 M8 70 100 2.82 P
BS88ZCM080075 M8 75 100 2.98 P
BS88ZCM080085 M8 85 100 3.21 P
BS88ZCM080100 M8 100 100 3.65 P
* = Bolt & Nut stock available.
? = Z: Zinc Plate (Z/P) P: Plain (PLN) / Black (Blk)

Zinc Plate
HEX SET SCREW

Class 8.8 AS1110.2

(mm) (Kg)
BS88ZCM100012 M10 12 150 2.58 P
BS88ZCM100016 M10 16 150 2.70 P *
BS88ZCM100020 M10 20 150 3.00 * P *
BS88ZCM100025 M10 25 150 3.40 * P *
BS88ZCM100030 M10 30 150 3.70 * P *
BS88ZCM100035 M10 35 150 4.10 P
BS88ZCM100040 M10 40 150 4.50 P
BS88ZCM100045 M10 45 150 5.06 P
BS88ZCM100050 M10 50 150 5.20 P
BS88ZCM100065 M10 65 75 3.29 P
BS88ZCM100070 M10 70 75 3.47 P
BS88ZCM100075 M10 75 75 3.66 P
BS88ZCM100080 M10 80 75 3.85 P
BS88ZCM100085 M10 85 75 4.04 P
BS88ZCM100100 M10 100 75 4.60 P
BS88ZCM120020 M12 20 100 2.90 * P *
BS88ZCM120025 M12 25 100 3.40 * P *
BS88ZCM120030 M12 30 100 3.70 * P *
BS88ZCM120035 M12 35 100 4.00 P
BS88ZCM120040 M12 40 100 4.50 P
BS88ZCM120045 M12 45 75 3.51 P
BS88ZCM120050 M12 50 50 3.90 P
BS88ZCM120055 M12 55 50 2.78 P
BS88ZCM120060 M12 60 50 2.91 P
BS88ZCM120065 M12 65 25 1.57 P
BS88ZCM120070 M12 70 25 1.66 P
BS88ZCM120075 M12 75 25 1.75 P
BS88ZCM120080 M12 80 25 1.84 P
BS88ZCM120100 M12 100 25 2.23 P
BS88ZCM140025 M14 25 25 0.99 * P *
BS88ZCM140030 M14 30 25 1.08 * P *
BS88ZCM140035 M14 35 25 1.17 * P *
BS88ZCM140040 M14 40 25 1.31 P
BS88ZCM140045 M14 45 25 1.37 P
BS88ZCM140050 M14 50 25 1.52 P

25
Zinc Plate
HEX SET SCREW

Class 8.8 AS1110.2

(mm) (Kg)
BS88ZCM160025 M16 25 25 1.15 * P *
BS88ZCM160030 M16 30 25 1.38 * P *
BS88ZCM160035 M16 35 25 1.65 * P *
BS88ZCM160040 M16 40 25 2.20 * P *
BS88ZCM160045 M16 45 25 2.48 P
BS88ZCM160050 M16 50 25 2.55 P
BS88ZCM160055 M16 55 25 2.68 P
BS88ZCM160060 M16 60 25 2.80 P
BS88ZCM160065 M16 65 25 2.95 P
BS88ZCM160070 M16 70 25 3.25 P
BS88ZCM160075 M16 75 25 3.30 P
BS88ZCM160080 M16 80 25 3.60 P
BS88ZCM160085 M16 85 25 3.78 P
BS88ZCM160090 M16 90 25 3.93 P
BS88ZCM160100 M16 100 25 4.25 P
BS88ZCM200035 M20 35 25 3.63 P
BS88ZCM200040 M20 40 25 3.80 * P *
BS88ZCM200045 M20 45 25 4.28 * P *
BS88ZCM200050 M20 50 25 4.30 * P *
BS88ZCM200055 M20 55 25 4.63 P
BS88ZCM200060 M20 60 25 4.75 P
BS88ZCM200065 M20 65 25 5.15 P
BS88ZCM200070 M20 70 20 4.20 P
BS88ZCM200075 M20 75 20 4.50 P
BS88ZCM200080 M20 80 20 4.76 P
BS88ZCM200085 M20 85 20 4.96 P
BS88ZCM200090 M20 90 20 5.16 P
BS88ZCM200100 M20 100 10 2.79 P
BS88ZCM240050 M24 50 5 1.02 * P *
BS88ZCM240055 M24 55 5 1.12 * P *
BS88ZCM240060 M24 60 5 1.22 P
BS88ZCM240065 M24 65 5 1.32 P
BS88ZCM240070 M24 70 5 1.42 P
BS88ZCM240075 M24 75 5 1.53 P
BS88ZCM240080 M24 80 5 1.70 P
BS88ZCM240085 M24 85 5 1.82 P
BS88ZCM240090 M24 90 5 1.97 P
BS88ZCM240100 M24 100 5 2.04 P
Bolt & Nut (Kit) codes start with K


Hex Bolt & Nut Class 8.8
Zinc Plate
Plain
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
Part Size Length Thread Pack BO Wgt Kit Wgt Blk Kit ZP BO ZP Kit
(mm) (mm) (Kg) (Kg)
BH88?CM060016 M6 16 16 200 1.00 1.50 P * P
BH88?CM060020 M6 20 20 200 1.20 1.60 P * P
BH88?CM060025 M6 25 18 200 1.40 1.80 P * P
BH88?CM060030 M6 30 18 200 1.60 2.00 P P P
BH88?CM060035 M6 35 18 200 1.80 2.20 P P P
BH88?CM060040 M6 40 18 200 2.00 2.40 P P P
BH88?CM060045 M6 45 18 200 2.40 2.60 P P
BH88?CM060050 M6 50 18 200 2.60 2.80 P P P
BH88?CM060055 M6 55 18 150 2.10 2.90 P P
BH88?CM060060 M6 60 18 150 2.30 2.60 P P P
BH88?CM060065 M6 65 18 150 2.40 2.70 P P P
BH88?CM060070 M6 70 18 150 2.60 2.80 P P P
BH88?CM060075 M6 75 18 150 2.70 3.00 P P P
BH88?CM060080 M6 80 18 150 2.82 P
BH88?CM080012 M8 12 12 200 1.60 3.00 * P
BH88?CM080016 M8 16 16 200 2.00 3.15 P * P
BH88?CM080020 M8 20 20 200 2.40 3.40 P * P
BH88?CM080025 M8 25 22 200 2.80 3.60 P * P
BH88?CM080030 M8 30 22 200 3.00 4.00 P P P
BH88?CM080035 M8 35 22 200 3.40 4.50 P P P
BH88?CM080040 M8 40 22 200 3.80 4.80 P P P
BH88?CM080045 M8 45 22 150 3.20 3.90 P P P
BH88?CM080050 M8 50 22 150 3.50 4.10 P P P
BH88?CM080055 M8 55 22 150 3.80 4.50 P P
BH88?CM080060 M8 60 22 150 4.10 4.90 P P P
BH88?CM080065 M8 65 22 150 4.40 5.00 P P P
BH88?CM080070 M8 70 22 100 3.10 3.50 P P P
BH88?CM080075 M8 75 22 100 3.20 3.80 P P P
BH88?CM080080 M8 80 22 100 3.40 4.00 P P P
BH88?CM080085 M8 85 22 100 3.78 P
BH88?CM080090 M8 90 22 100 3.50 4.30 P P P
BH88?CM080095 M8 95 22 100 4.20 P
BH88?CM080100 M8 100 22 100 4.30 4.80 P P P
BH88?CM080110 M8 110 22 100 4.62 P
BH88?CM080120 M8 120 22 100 4.99 P
BH88?CM080130 M8 130 28 100 5.33 P
* = Set Screw stock available.


27
Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
(mm) (mm) (Kg) (Kg)
BH88?CM100016 M10 16 16 150 3.00 4.00 * P
BH88?CM100020 M10 20 20 150 3.50 4.30 P * P
BH88?CM100025 M10 25 25 150 3.90 4.60 P * P
BH88?CM100030 M10 30 26 150 4.50 5.10 P * P
BH88?CM100035 M10 35 26 150 5.00 5.60 P P P
BH88?CM100040 M10 40 26 150 5.40 6.00 P P P
BH88?CM100045 M10 45 26 150 5.90 6.50 P P P
BH88?CM100050 M10 50 26 75 3.20 3.50 P P P
BH88?CM100055 M10 55 26 75 3.40 3.70 P P P
BH88?CM100060 M10 60 26 75 3.60 3.90 P P P
BH88?CM100065 M10 65 26 75 3.80 4.10 P P P
BH88?CM100070 M10 70 26 75 4.10 4.40 P P P
BH88?CM100075 M10 75 26 75 4.20 4.60 P P P
BH88?CM100080 M10 80 26 75 4.40 4.80 P P P
BH88?CM100085 M10 85 26 75 4.68 P
BH88?CM100090 M10 90 26 50 3.20 3.50 P P P
BH88?CM100100 M10 100 26 50 3.50 3.80 P P P
BH88?CM100110 M10 110 26 50 3.80 4.10 P P P
BH88?CM100120 M10 120 26 50 4.10 4.40 P P P
BH88?CM100130 M10 130 32 50 4.40 4.70 P P P
BH88?CM100140 M10 140 32 50 4.50 4.80 P P
BH88?CM100150 M10 150 32 50 4.50 4.90 P P
BH88?CM100160 M10 160 32 50 5.36 P
BH88?CM100170 M10 170 32 50 5.45 P
BH88?CM100180 M10 180 32 25 2.90 P
BH88?CM100190 M10 190 32 25 3.08 P
BH88?CM100200 M10 200 32 25 3.22 P


Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
(mm) (mm) (Kg) (Kg)
BH88?CM120020 M12 20 20 75 2.80 3.90 P * P
BH88?CM120025 M12 25 25 75 2.90 4.05 P * P
BH88?CM120030 M12 30 30 75 3.10 4.20 P * P
BH88?CM120035 M12 35 30 75 3.50 4.57 P P P
BH88?CM120040 M12 40 30 75 3.80 4.87 P P P
BH88?CM120045 M12 45 30 75 4.10 5.25 P P P
BH88?CM120050 M12 50 30 50 3.00 5.55 P P P
BH88?CM120055 M12 55 30 50 3.20 3.90 P P P
BH88?CM120060 M12 60 30 50 3.30 4.05 P P P
BH88?CM120065 M12 65 30 50 3.50 4.20 P P P
BH88?CM120070 M12 70 30 50 3.70 4.40 P P P
BH88?CM120075 M12 75 30 25 1.90 2.30 P P P
BH88?CM120080 M12 80 30 25 2.00 2.35 P P P
BH88?CM120085 M12 85 30 25 2.00 2.40 P P
BH88?CM120090 M12 90 30 25 2.10 2.50 P P P
BH88?CM120100 M12 100 30 25 2.50 2.90 P P P
BH88?CM120110 M12 110 30 25 2.90 3.25 P P P
BH88?CM120120 M12 120 30 25 3.10 3.50 P P P
BH88?CM120130 M12 130 36 25 3.30 3.65 P P P
BH88?CM120140 M12 140 36 25 3.60 3.92 P P P
BH88?CM120150 M12 150 36 25 3.80 4.20 P P P
BH88?CM120160 M12 160 36 20 3.13 P
BH88?CM120170 M12 170 36 20 3.31 P
BH88?CM120180 M12 180 36 20 3.50 4.40 P P
BH88?CM120190 M12 190 36 20 3.67 P
BH88?CM120200 M12 200 36 20 3.90 4.60 P P
BH88?CM140025 M14 25 25 25 1.33 1.75 P *
BH88?CM140030 M14 30 30 25 1.45 1.93 P *
BH88?CM140035 M14 35 35 25 1.57 2.11 P *
BH88?CM140040 M14 40 34 25 1.70 2.27 P P
BH88?CM140045 M14 45 34 25 1.82 2.45 P
BH88?CM140050 M14 50 34 25 2.05 2.63 P
BH88?CM140055 M14 55 34 25 2.21 2.79 P P
BH88?CM140060 M14 60 34 25 2.36 2.91 P P
BH88?CM140065 M14 65 34 25 2.47 3.05 P P
BH88?CM140070 M14 70 34 25 2.63 3.19 P P
BH88?CM140075 M14 75 34 25 2.78 3.35 P P
BH88?CM140080 M14 80 34 25 2.93 3.45 P P
BH88?CM140085 M14 85 34 25 3.05 3.58 P P
BH88?CM140090 M14 90 34 25 3.18 3.73 P P
BH88?CM140100 M14 100 34 25 3.48 4.11 P P

29
Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
(mm) (mm) (Kg) (Kg)
BH88?CM160025 M16 25 25 25 1.50 2.82 P * P
BH88?CM160030 M16 30 30 25 1.70 2.47 P * P
BH88?CM160035 M16 35 35 25 1.90 2.70 P * P
BH88?CM160040 M16 40 38 25 2.20 2.92 P * P
BH88?CM160045 M16 45 38 25 2.40 3.15 P P P
BH88?CM160050 M16 50 38 25 2.60 3.40 P P P
BH88?CM160055 M16 55 38 25 2.90 3.63 P P P
BH88?CM160060 M16 60 38 25 3.00 3.80 P P P
BH88?CM160065 M16 65 38 25 3.20 4.00 P P P
BH88?CM160070 M16 70 38 25 3.40 4.18 P P P
BH88?CM160075 M16 75 38 25 3.60 4.40 P P P
BH88?CM160080 M16 80 38 25 3.80 4.55 P P P
BH88?CM160085 M16 85 38 25 4.00 5.00 P P
BH88?CM160090 M16 90 38 25 4.20 5.95 P P P
BH88?CM160100 M16 100 38 25 4.60 5.33 P P P
BH88?CM160110 M16 110 38 15 3.00 3.43 P P P
BH88?CM160120 M16 120 38 15 3.20 3.62 P P P
BH88?CM160130 M16 130 44 15 3.40 3.86 P P P
BH88?CM160140 M16 140 44 15 3.70 4.13 P P P
BH88?CM160150 M16 150 44 15 3.90 4.33 P P P
BH88?CM160160 M16 160 44 15 4.17 P
BH88?CM160170 M16 170 44 15 4.45 P
BH88?CM160180 M16 180 44 15 4.70 5.20 P P P
BH88?CM160190 M16 190 44 15 4.92 P
BH88?CM160200 M16 200 44 15 5.20 5.62 P P P
BH88?CM160210 M16 210 57 10 3.58 P
BH88?CM160220 M16 220 57 10 3.74 P
BH88?CM160230 M16 230 57 10 3.90 P
BH88?CM160240 M16 240 57 10 4.06 P
BH88?CM160250 M16 250 57 10 4.22 P
BH88?CM160260 M16 260 57 10 4.38 P
BH88?CM160270 M16 270 57 10 4.55 P
BH88?CM160280 M16 280 57 10 4.71 P
BH88?CM160290 M16 290 57 10 4.87 P
BH88?CM160300 M16 300 57 10 5.02 P


Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
(mm) (mm) (Kg) (Kg)
BH88?CM180040 M18 40 40 25 3.03 4.32 P *
BH88?CM180050 M18 50 42 25 3.43 4.62 P P
BH88?CM180060 M18 60 42 20 3.06 4.10 P P
BH88?CM180070 M18 70 42 20 3.62 4.47 P P
BH88?CM180075 M18 75 42 20 3.82 4.70 P P
BH88?CM180080 M18 80 42 20 4.02 4.89 P P
BH88?CM180090 M18 90 42 20 4.40 5.34 P P
BH88?CM180100 M18 100 42 20 4.80 5.80 P P
BH88?CM180120 M18 120 42 15 4.20 4.86 P P
BH88?CM180150 M18 150 48 15 5.03 5.65 P P


31
Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
(mm) (mm) (Kg) (Kg)
BH88?CM200040 M20 40 40 25 4.25 5.72 P * P
BH88?CM200045 M20 45 45 25 4.30 5.78 P * P
BH88?CM200050 M20 50 46 25 4.40 5.85 P * P
BH88?CM200055 M20 55 46 25 4.60 6.10 P P P
BH88?CM200060 M20 60 46 25 4.80 6.47 P P P
BH88?CM200065 M20 65 46 20 5.00 6.70 P P P
BH88?CM200070 M20 70 46 20 5.20 6.90 P P P
BH88?CM200075 M20 75 46 20 5.40 7.00 P P P
BH88?CM200080 M20 80 46 20 5.60 7.20 P P P
BH88?CM200085 M20 85 46 20 5.70 7.40 P P
BH88?CM200090 M20 90 46 20 5.85 7.60 P P P
BH88?CM200100 M20 100 46 10 3.10 3.67 P P P
BH88?CM200110 M20 110 46 10 3.30 3.87 P P P
BH88?CM200120 M20 120 46 10 3.50 4.06 P P P
BH88?CM200130 M20 130 52 10 3.70 4.26 P P P
BH88?CM200140 M20 140 52 10 3.90 4.45 P P P
BH88?CM200150 M20 150 52 10 4.10 4.65 P P P
BH88?CM200160 M20 160 52 10 4.46 P
BH88?CM200170 M20 170 52 10 4.70 5.00 P P
BH88?CM200180 M20 180 52 10 4.90 5.53 P P P
BH88?CM200190 M20 190 52 10 5.19 P
BH88?CM200200 M20 200 52 10 5.50 6.04 P P P
BH88?CM200210 M20 210 65 5 2.84 P
BH88?CM200220 M20 220 65 5 2.95 P
BH88?CM200230 M20 230 65 5 3.06 P
BH88?CM200240 M20 240 65 5 3.21 P
BH88?CM200250 M20 250 65 5 3.29 P
BH88?CM200260 M20 260 65 5 3.46 P
BH88?CM200270 M20 270 65 5 3.54 P
BH88?CM200280 M20 280 65 5 3.63 P
BH88?CM200290 M20 290 65 5 3.74 P
BH88?CM200300 M20 300 65 5 3.85 P


Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
(mm) (mm) (Kg) (Kg)
BH88?CM240050 M24 50 50 5 1.56 2.08 P * P
BH88?CM240055 M24 55 54 5 1.60 2.16 P * P
BH88?CM240060 M24 60 54 5 1.70 2.24 P P P
BH88?CM240065 M24 65 54 5 1.80 2.36 P P P
BH88?CM240070 M24 70 54 5 1.90 2.45 P P P
BH88?CM240075 M24 75 54 5 2.00 2.53 P P
BH88?CM240080 M24 80 54 5 2.07 2.59 P P P
BH88?CM240085 M24 85 54 5 2.10 2.68 P P
BH88?CM240090 M24 90 54 5 2.20 2.73 P P P
BH88?CM240100 M24 100 54 5 2.40 2.87 P P P
BH88?CM240110 M24 110 54 5 2.50 3.02 P P P
BH88?CM240120 M24 120 54 5 2.60 3.16 P P P
BH88?CM240130 M24 130 60 5 2.80 3.30 P P P
BH88?CM240140 M24 140 60 5 2.90 3.44 P P P
BH88?CM240150 M24 150 60 5 3.10 3.58 P P P
BH88?CM240160 M24 160 60 5 3.20 3.75 P P P
BH88?CM240170 M24 170 60 5 3.30 P
BH88?CM240180 M24 180 60 5 3.40 4.06 P P P
BH88?CM240190 M24 190 60 5 3.54 P
BH88?CM240200 M24 200 60 5 3.65 4.35 P P P
BH88?CM240210 M24 210 73 5 3.80 P
BH88?CM240220 M24 220 73 5 4.00 4.49 P P P
BH88?CM240230 M24 230 73 5 4.20 P
BH88?CM240240 M24 240 73 5 4.40 4.91 P P P
BH88?CM240250 M24 250 73 5 4.50 5.50 P P P
BH88?CM240260 M24 260 73 5 5.75 P
BH88?CM240270 M24 270 73 5 5.85 P
BH88?CM240280 M24 280 73 5 6.05 P
BH88?CM240290 M24 290 73 5 6.15 P
BH88?CM240300 M24 300 73 5 6.30 P


33
Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
Part Size Length Thread Pack Kit Wgt Blk Kit

(mm) (mm) (Kg)
KBH88PCM300070 M30 70 66 5 3.75 P
KBH88PCM300075 M30 75 66 5 4.05 P
KBH88PCM300080 M30 80 66 5 4.25 P
KBH88PCM300085 M30 85 66 5 4.75 P
KBH88PCM300090 M30 90 66 5 5.15 P
KBH88PCM300100 M30 100 66 5 5.50 P
KBH88PCM300110 M30 110 66 5 5.85 P
KBH88PCM300120 M30 120 66 5 6.10 P
KBH88PCM300130 M30 130 72 5 6.40 P
KBH88PCM300140 M30 140 72 5 6.65 P
KBH88PCM300150 M30 150 72 5 7.00 P
KBH88PCM300160 M30 160 72 5 7.30 P
KBH88PCM300170 M30 170 72 5 7.50 P
KBH88PCM300180 M30 180 72 5 7.80 P
KBH88PCM300190 M30 190 72 5 8.10 P
KBH88PCM300200 M30 200 72 5 8.40 P
KBH88PCM300210 M30 210 85 5 8.75 P
KBH88PCM300220 M30 220 85 5 9.10 P
KBH88PCM300230 M30 230 85 5 9.40 P
KBH88PCM300240 M30 240 85 5 9.60 P
KBH88PCM300250 M30 250 85 5 9.95 P
KBH88PCM300260 M30 260 85 5 10.07 P
KBH88PCM300270 M30 270 85 5 10.37 P
KBH88PCM300280 M30 280 85 5 10.65 P
KBH88PCM300290 M30 290 85 5 10.96 P
KBH88PCM300300 M30 300 85 5 11.25 P
KBH88PCM300320 M30 320 85 2 4.74 P
KBH88PCM300350 M30 350 85 2 5.10 P
KBH88PCM300380 M30 380 85 2 5.45 P
KBH88PCM300400 M30 400 85 2 5.69 P

Zinc Plate
Plain / Black
HEX BOLT & NUT

Class 8.8 AS1110.1 / Class 8 AS1112.1
Part Size Length Thread Pack Kit Wgt Blk Kit

(mm) (mm) (Kg)
KBH88PCM360070 M36 70 70 2 2.20 P
KBH88PCM360075 M36 75 75 2 2.40 P
KBH88PCM360090 M36 90 78 2 2.80 P
KBH88PCM360100 M36 100 78 2 2.94 P
KBH88PCM360110 M36 110 78 2 3.06 P
KBH88PCM360120 M36 120 78 2 3.16 P
KBH88PCM360130 M36 130 84 2 3.26 P
KBH88PCM360140 M36 140 84 2 3.42 P
KBH88PCM360150 M36 150 84 2 3.58 P
KBH88PCM360160 M36 160 84 2 3.80 P
KBH88PCM360170 M36 170 84 2 3.90 P
KBH88PCM360180 M36 180 84 2 4.00 P
KBH88PCM360190 M36 190 84 2 4.14 P
KBH88PCM360200 M36 200 84 2 4.26 P
KBH88PCM360210 M36 210 97 2 4.50 P
KBH88PCM360220 M36 220 97 2 4.58 P
KBH88PCM360230 M36 230 97 2 4.70 P
KBH88PCM360240 M36 240 97 2 4.90 P
KBH88PCM360250 M36 250 97 2 5.10 P
KBH88PCM360260 M36 260 97 2 5.40 P
KBH88PCM360270 M36 270 97 2 5.50 P
KBH88PCM360280 M36 280 97 2 5.54 P
KBH88PCM360290 M36 290 97 2 5.60 P
KBH88PCM360300 M36 300 97 2 5.64 P

35
Hex Bolt & Nut Grade 5
Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 5 AS2465
Part Size Length Pack BO Wgt Kit Wgt Blk BO Blk Kit ZP BO ZP Kit
(inch) (Kg) (Kg)
BHG5?C0250075 1/4″ 3/4″ 200 1.40 2.00 P P P
BHG5?C0250100 1/4″ 1″ 200 1.60 2.20 P P P
BHG5?C0250125 1/4″ 1 1/4″ 200 1.89 P
BHG5?C0250150 1/4″ 1 1/2″ 200 2.20 2.80 P P P
BHG5?C0250175 1/4″ 1 3/4″ 200 2.52 P
BHG5?C0250200 1/4″ 2″ 200 2.80 3.40 P P P
BHG5?C0250225 1/4″ 2 1/4″ 150 2.36 P
BHG5?C0250250 1/4″ 2 1/2″ 150 2.55 3.00 P P P
BHG5?C0250275 1/4″ 2 3/4″ 150 2.80 P
BHG5?C0250300 1/4″ 3″ 150 3.00 3.45 P P P
BHG5?C0250350 1/4″ 3 1/2″ 100 3.60 4.00 P P
BHG5?C0250400 1/4″ 4″ 100 4.05 4.45 P P P
BHG5?C0250450 1/4″ 4 1/2″ 100 2.97 P
BHG5?C0310050 5/16″ 1/2″ 200 1.76 P
BHG5?C0310075 5/16″ 3/4″ 200 2.20 3.20 P P P P
BHG5?C0310100 5/16″ 1″ 200 2.60 3.60 P P P P
BHG5?C0310125 5/16″ 1 1/4″ 200 3.00 4.00 P P
BHG5?C0310150 5/16″ 1 1/2″ 200 3.60 4.60 P P P
BHG5?C0310175 5/16″ 1 3/4″ 150 3.00 3.75 P P
BHG5?C0310200 5/16″ 2″ 150 3.45 4.20 P P P
BHG5?C0310225 5/16″ 2 1/4″ 150 3.76 P
BHG5?C0310250 5/16″ 2 1/2″ 150 4.05 4.80 P P P
BHG5?C0310275 5/16″ 2 3/4″ 100 2.99 P
BHG5?C0310300 5/16″ 3″ 100 3.20 3.70 P P P
BHG5?C0310350 5/16″ 3 1/2″ 100 3.70 4.21 P P
BHG5?C0310400 5/16″ 4″ 100 4.20 4.70 P P
BHG5?C0310450 5/16″ 4 1/2″ 100 4.70 P
BHG5?C0310500 5/16″ 5″ 100 5.20 P
BHG5?C0310600 5/16″ 6″ 100 6.24 P


Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 5 AS2465
(inch) (Kg) (Kg)
BHG5?C0370050 3/8″ 1/2″ 200 2.56 P
BHG5?C0370075 3/8″ 3/4″ 200 3.20 4.60 P P P P
BHG5?C0370100 3/8″ 1″ 200 3.80 5.20 P P P P
BHG5?C0370125 3/8″ 1 1/4″ 200 4.40 5.80 P P P P
BHG5?C0370150 3/8″ 1 1/2″ 150 3.90 4.95 P P P P
BHG5?C0370175 3/8″ 1 3/4″ 150 4.35 5.40 P P P
BHG5?C0370200 3/8″ 2″ 100 3.30 4.00 P P P
BHG5?C0370225 3/8″ 2 1/4″ 100 3.62 P
BHG5?C0370250 3/8″ 2 1/2″ 100 4.00 4.70 P P P
BHG5?C0370275 3/8″ 2 3/4″ 100 4.39 P
BHG5?C0370300 3/8″ 3″ 100 4.70 5.40 P P P
BHG5?C0370350 3/8″ 3 1/2″ 50 2.70 3.05 P P P
BHG5?C0370400 3/8″ 4″ 50 3.05 3.40 P P P
BHG5?C0370450 3/8″ 4 1/2″ 50 3.40 3.75 P P P
BHG5?C0370500 3/8″ 5″ 50 3.75 4.10 P P P
BHG5?C0370550 3/8″ 5 1/2″ 50 4.45 P
BHG5?C0370600 3/8″ 6″ 50 5.09 5.44 P P P
BHG5?C0430150 7/16″ 1 1/2″ 100 3.50 P
BHG5?C0430200 7/16″ 2″ 100 4.50 P
BHG5?C0430250 7/16″ 2 1/2″ 75 4.13 P
BHG5?C0430300 7/16″ 3″ 75 4.80 P
BHG5?C0430400 7/16″ 4″ 50 4.20 P


37
Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C0250050 1/4″ 1/2″ 200 1.07 1.72 P P
BHG8?C0250075 1/4″ 3/4″ 200 1.40 2.00 P P P P
BHG8?C0250100 1/4″ 1″ 200 1.60 2.20 P P P P
BHG8?C0250125 1/4″ 1 1/4″ 200 1.89 2.54 P P P
BHG8?C0250150 1/4″ 1 1/2″ 200 2.21 2.80 P P P P
BHG8?C0250175 1/4″ 1 3/4″ 200 2.52 3.12 P P P
BHG8?C0250200 1/4″ 2″ 200 2.80 3.40 P P P P
BHG8?C0250225 1/4″ 2 1/4″ 150 2.36 2.84 P P P
BHG8?C0250250 1/4″ 2 1/2″ 150 2.60 3.00 P P P P
BHG8?C0250275 1/4″ 2 3/4″ 150 2.83 3.31 P P P
BHG8?C0250300 1/4″ 3″ 150 3.06 3.45 P P P P
BHG8?C0250325 1/4″ 3 1/4″ 150 3.78 P
BHG8?C0250350 1/4″ 3 1/2″ 100 2.36 2.68 P P P P
BHG8?C0250400 1/4″ 4″ 100 2.50 3.00 P P P P
BHG8?C0250450 1/4″ 4 1/2″ 100 2.98 3.31 P P P
BHG8?C0250500 1/4″ 5″ 100 3.30 3.62 P P P
BHG8?C0250550 1/4″ 5 1/2″ 100 3.61 3.93 P P P
BHG8?C0250600 1/4″ 6″ 100 3.92 4.25 P P P
BHG8?C0310050 5/16″ 1/2″ 200 1.81 2.77 P P P
BHG8?C0310075 5/16″ 3/4″ 200 2.20 3.20 P P P P
BHG8?C0310100 5/16″ 1″ 200 2.60 3.60 P P P P
BHG8?C0310125 5/16″ 1 1/4″ 200 3.00 4.00 P P P P
BHG8?C0310150 5/16″ 1 1/2″ 200 3.60 4.60 P P P P
BHG8?C0310175 5/16″ 1 3/4″ 150 3.00 3.75 P P P P
BHG8?C0310200 5/16″ 2″ 150 3.45 4.20 P P P P
BHG8?C0310225 5/16″ 2 1/4″ 150 3.76 4.48 P P P
BHG8?C0310250 5/16″ 2 1/2″ 150 4.13 4.80 P P P P
BHG8?C0310275 5/16″ 2 3/4″ 100 2.99 3.48 P P P
BHG8?C0310300 5/16″ 3″ 100 3.20 3.70 P P P P
BHG8?C0310325 5/16″ 3 1/4″ 100 3.97 P
BHG8?C0310350 5/16″ 3 1/2″ 100 3.73 4.21 P P P P
BHG8?C0310400 5/16″ 4″ 100 4.22 4.70 P P P P
BHG8?C0310450 5/16″ 4 1/2″ 100 4.71 5.19 P P P
BHG8?C0310500 5/16″ 5″ 100 5.19 5.67 P P P
BHG8?C0310550 5/16″ 5 1/2″ 100 5.68 6.16 P P P
BHG8?C0310600 5/16″ 6″ 100 6.17 6.65 P P P


Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C0370050 3/8″ 1/2″ 200 2.66 4.06 P P P
BHG8?C0370075 3/8″ 3/4″ 200 3.20 4.60 P P P P
BHG8?C0370100 3/8″ 1″ 200 3.80 5.20 P P P P
BHG8?C0370125 3/8″ 1 1/4″ 200 4.41 5.80 P P P P
BHG8?C0370150 3/8″ 1 1/2″ 150 3.90 4.95 P P P P
BHG8?C0370175 3/8″ 1 3/4″ 100 2.92 3.60 P P P P
BHG8?C0370200 3/8″ 2″ 100 3.26 4.00 P P P P
BHG8?C0370225 3/8″ 2 1/4″ 100 3.62 4.32 P P P
BHG8?C0370250 3/8″ 2 1/2″ 100 3.97 4.70 P P P P
BHG8?C0370275 3/8″ 2 3/4″ 100 4.32 5.02 P P P
BHG8?C0370300 3/8″ 3″ 100 4.68 5.40 P P P P
BHG8?C0370325 3/8″ 3 1/4″ 100 5.47 5.80 P P
BHG8?C0370350 3/8″ 3 1/2″ 50 2.69 3.05 P P P P
BHG8?C0370400 3/8″ 4″ 50 3.04 3.40 P P P P
BHG8?C0370450 3/8″ 4 1/2″ 50 3.39 3.75 P P P P
BHG8?C0370500 3/8″ 5″ 50 3.75 4.10 P P P P
BHG8?C0370550 3/8″ 5 1/2″ 50 4.10 4.45 P P P
BHG8?C0370600 3/8″ 6″ 50 4.45 4.80 P P P P
BHG8?C0430075 7/16″ 3/4″ 100 2.31 3.59 P P
BHG8?C0430100 7/16″ 1″ 100 2.70 3.90 P P P P
BHG8?C0430125 7/16″ 1 1/4″ 100 3.07 4.35 P P P
BHG8?C0430150 7/16″ 1 1/2″ 100 3.50 4.70 P P P P
BHG8?C0430175 7/16″ 1 3/4″ 100 4.03 5.25 P P P
BHG8?C0430200 7/16″ 2″ 100 4.50 5.70 P P P P
BHG8?C0430225 7/16″ 2 1/4″ 75 3.75 4.71 P P P
BHG8?C0430250 7/16″ 2 1/2″ 75 4.13 5.03 P P P P
BHG8?C0430275 7/16″ 2 3/4″ 75 4.47 5.43 P P P
BHG8?C0430300 7/16″ 3″ 75 4.83 5.70 P P P P
BHG8?C0430350 7/16″ 3 1/2″ 50 3.70 4.34 P P P P
BHG8?C0430400 7/16″ 4″ 50 4.18 4.82 P P P P
BHG8?C0430450 7/16″ 4 1/2″ 50 4.66 5.30 P P P P
BHG8?C0430500 7/16″ 5″ 50 5.14 5.78 P P P P
BHG8?C0430550 7/16″ 5 1/2″ 50 5.62 6.26 P P P
BHG8?C0430600 7/16″ 6″ 50 6.10 6.74 P P P
BHG8?C0430650 7/16″ 6 1/2″ 25 3.61 P
BHG8?C0430700 7/16″ 7″ 25 3.85 P


39
Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C0500075 1/2″ 3/4″ 75 2.76 4.00 P P P
BHG8?C0500100 1/2″ 1″ 75 3.15 4.35 P P P P
BHG8?C0500125 1/2″ 1 1/4″ 75 3.53 4.73 P P P P
BHG8?C0500150 1/2″ 1 1/2″ 75 3.98 5.18 P P P P
BHG8?C0500175 1/2″ 1 3/4″ 75 4.43 5.63 P P P P
BHG8?C0500200 1/2″ 2″ 50 3.30 4.10 P P P P
BHG8?C0500225 1/2″ 2 1/4″ 50 3.57 4.40 P P P P
BHG8?C0500250 1/2″ 2 1/2″ 50 3.90 4.70 P P P P
BHG8?C0500275 1/2″ 2 3/4″ 50 4.20 5.00 P P P P
BHG8?C0500300 1/2″ 3″ 25 2.25 2.65 P P P P
BHG8?C0500325 1/2″ 3 1/4″ 25 2.84 P P
BHG8?C0500350 1/2″ 3 1/2″ 25 2.58 2.98 P P P P
BHG8?C0500400 1/2″ 4″ 25 2.88 3.28 P P P P
BHG8?C0500450 1/2″ 4 1/2″ 25 3.20 3.60 P P P P
BHG8?C0500500 1/2″ 5″ 25 3.50 3.90 P P P P
BHG8?C0500550 1/2″ 5 1/2″ 25 3.83 4.23 P P P P
BHG8?C0500600 1/2″ 6″ 25 4.13 4.53 P P P P
BHG8?C0500650 1/2″ 6 1/2″ 20 3.58 3.90 P P P
BHG8?C0500700 1/2″ 7″ 20 3.80 4.12 P P P
BHG8?C0500750 1/2″ 7 1/2″ 20 4.09 4.24 P P P
BHG8?C0500800 1/2″ 8″ 20 4.30 4.48 P P P
BHG8?C0500900 1/2″ 9″ 20 4.81 P
BHG8?C0501000 1/2″ 10″ 20 5.31 P
BHG8?C0501100 1/2″ 11″ 10 2.91 P
BHG8?C0501200 1/2″ 12″ 10 3.16 P
BHG8?C0560100 9/16″ 1″ 25 1.28 P P
BHG8?C0560125 9/16″ 1 1/4″ 25 1.44 P P
BHG8?C0560150 9/16″ 1 1/2″ 25 1.60 P P
BHG8?C0560175 9/16″ 1 3/4″ 25 1.80 P P
BHG8?C0560200 9/16″ 2″ 25 2.00 P P
BHG8?C0560225 9/16″ 2 1/4″ 25 2.20 P P
BHG8?C0560250 9/16″ 2 1/2″ 25 2.40 P P
BHG8?C0560300 9/16″ 3″ 25 2.80 P P
BHG8?C0560350 9/16″ 3 1/2″ 25 3.20 P P
BHG8?C0560400 9/16″ 4″ 25 3.60 P P
BHG8?C0560450 9/16″ 4 1/2″ 15 2.68 P P
BHG8?C0560500 9/16″ 5″ 15 2.70 P P
BHG8?C0560550 9/16″ 5 1/2″ 15 2.87 P P
BHG8?C0560600 9/16″ 6″ 15 3.24 P P


Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C0620100 5/8″ 1″ 25 1.73 2.55 P P P
BHG8?C0620125 5/8″ 1 1/4″ 25 1.93 2.73 P P P P
BHG8?C0620150 5/8″ 1 1/2″ 25 2.13 2.93 P P P P
BHG8?C0620175 5/8″ 1 3/4″ 25 2.38 3.18 P P P P
BHG8?C0620200 5/8″ 2″ 25 2.60 3.40 P P P P
BHG8?C0620225 5/8″ 2 1/4″ 25 2.83 3.66 P P P P
BHG8?C0620250 5/8″ 2 1/2″ 25 3.08 3.88 P P P P
BHG8?C0620275 5/8″ 2 3/4″ 25 3.34 4.14 P P P P
BHG8?C0620300 5/8″ 3″ 25 3.58 4.38 P P P P
BHG8?C0620325 5/8″ 3 1/4″ 25 3.81 P P
BHG8?C0620350 5/8″ 3 1/2″ 25 4.05 4.85 P P P P
BHG8?C0620400 5/8″ 4″ 25 4.55 5.35 P P P P
BHG8?C0620450 5/8″ 4 1/2″ 15 3.03 3.52 P P P P
BHG8?C0620500 5/8″ 5″ 15 3.32 3.80 P P P P
BHG8?C0620550 5/8″ 5 1/2″ 15 3.62 4.10 P P P P
BHG8?C0620600 5/8″ 6″ 15 3.90 4.38 P P P P
BHG8?C0620650 5/8″ 6 1/2″ 15 4.05 4.60 P P P
BHG8?C0620700 5/8″ 7″ 15 4.22 4.89 P P P
BHG8?C0620750 5/8″ 7 1/2″ 15 4.49 5.17 P P P
BHG8?C0620800 5/8″ 8″ 15 5.15 5.46 P P P
BHG8?C0620850 5/8″ 8 1/2″ 15 5.37 5.86 P P
BHG8?C0620900 5/8″ 9″ 15 5.67 6.16 P P
BHG8?C0620950 5/8″ 9 1/2″ 15 6.45 P
BHG8?C0621000 5/8″ 10″ 15 6.43 6.75 P P
BHG8?C0621100 5/8″ 11″ 10 4.56 P
BHG8?C0621200 5/8″ 12″ 10 4.90 P
BHG8?C0621300 5/8″ 13″ 10 5.16 P
BHG8?C0621400 5/8″ 14″ 10 5.60 P
BHG8?C0621500 5/8″ 15″ 10 5.76 P


41
Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C0750100 3/4″ 1″ 25 2.78 4.08 P P
BHG8?C0750125 3/4″ 1 1/4″ 25 3.07 4.37 P P
BHG8?C0750150 3/4″ 1 1/2″ 25 3.38 4.70 P P P P
BHG8?C0750175 3/4″ 1 3/4″ 25 3.58 4.96 P P P
BHG8?C0750200 3/4″ 2″ 25 3.98 5.30 P P P P
BHG8?C0750225 3/4″ 2 1/4″ 25 4.33 5.64 P P P P
BHG8?C0750250 3/4″ 2 1/2″ 20 3.76 4.85 P P P P
BHG8?C0750275 3/4″ 2 3/4″ 20 4.04 5.10 P P P P
BHG8?C0750300 3/4″ 3″ 20 4.32 5.38 P P P P
BHG8?C0750325 3/4″ 3 1/4″ 20 4.60 5.64 P P
BHG8?C0750350 3/4″ 3 1/2″ 20 4.88 5.94 P P P P
BHG8?C0750400 3/4″ 4″ 10 2.72 3.25 P P P P
BHG8?C0750450 3/4″ 4 1/2″ 10 3.00 3.53 P P P P
BHG8?C0750500 3/4″ 5″ 10 3.29 3.82 P P P P
BHG8?C0750550 3/4″ 5 1/2″ 10 3.57 4.10 P P P
BHG8?C0750600 3/4″ 6″ 10 3.85 4.38 P P P P
BHG8?C0750650 3/4″ 6 1/2″ 10 4.13 4.57 P P P
BHG8?C0750700 3/4″ 7″ 10 4.41 4.94 P P P P
BHG8?C0750750 3/4″ 7 1/2″ 10 4.70 5.11 P P P
BHG8?C0750800 3/4″ 8″ 10 4.98 5.38 P P P P
BHG8?C0750850 3/4″ 8 1/2″ 5 2.65 P
BHG8?C0750900 3/4″ 9″ 5 2.77 3.03 P P P P
BHG8?C0750950 3/4″ 9 1/2″ 5 2.95 P
BHG8?C0751000 3/4″ 10″ 5 3.06 3.32 P P P
BHG8?C0751100 3/4″ 11″ 5 3.34 P
BHG8?C0751200 3/4″ 12″ 5 3.60 P
BHG8?C0751300 3/4″ 13″ 5 3.87 P
BHG8?C0751400 3/4″ 14″ 5 4.11 P
BHG8?C0751500 3/4″ 15″ 5 4.40 P


Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C0870150 7/8″ 1 1/2″ 10 2.82 P
BHG8?C0870175 7/8″ 1 3/4″ 10 2.99 P
BHG8?C0870200 7/8″ 2″ 10 2.32 3.18 P P P
BHG8?C0870225 7/8″ 2 1/4″ 10 2.50 3.33 P P P
BHG8?C0870250 7/8″ 2 1/2″ 10 2.68 3.54 P P P
BHG8?C0870275 7/8″ 2 3/4″ 10 2.87 P P
BHG8?C0870300 7/8″ 3″ 10 3.07 3.93 P P P
BHG8?C0870350 7/8″ 3 1/2″ 10 3.45 4.31 P P P
BHG8?C0870375 7/8″ 3 3/4″ 10 4.46 P
BHG8?C0870400 7/8″ 4″ 10 3.84 4.70 P P P
BHG8?C0870450 7/8″ 4 1/2″ 10 4.22 5.08 P P P
BHG8?C0870500 7/8″ 5″ 10 4.60 5.46 P P P
BHG8?C0870550 7/8″ 5 1/2″ 10 4.99 5.85 P P P
BHG8?C0870600 7/8″ 6″ 10 5.37 6.21 P P P
BHG8?C0870650 7/8″ 6 1/2″ 5 2.88 3.25 P P P
BHG8?C0870700 7/8″ 7″ 5 3.07 3.43 P P P
BHG8?C0870750 7/8″ 7 1/2″ 5 3.26 3.62 P P
BHG8?C0870800 7/8″ 8″ 5 3.45 3.80 P P P
BHG8?C0870850 7/8″ 8 1/2″ 5 3.66 P
BHG8?C0870900 7/8″ 9″ 5 3.84 4.26 P P
BHG8?C0870950 7/8″ 9 1/2″ 5 4.03 P
BHG8?C0871000 7/8″ 10″ 5 4.22 4.64 P P
BHG8?C0871100 7/8″ 11″ 5 4.56 P
BHG8?C0871200 7/8″ 12″ 5 4.93 P
BHG8?C0871300 7/8″ 13″ 5 5.30 P
BHG8?C0871400 7/8″ 14″ 5 5.67 P


43
Zinc Plate
Plain / Black
UNC HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?C1000200 1″ 2″ 5 1.59 2.22 P P P
BHG8?C1000225 1″ 2 1/4″ 5 1.70 P P
BHG8?C1000250 1″ 2 1/2″ 5 1.81 2.44 P P P
BHG8?C1000275 1″ 2 3/4″ 5 1.95 P P
BHG8?C1000300 1″ 3″ 5 2.07 2.73 P P P P
BHG8?C1000350 1″ 3 1/2″ 5 2.32 2.95 P P P P
BHG8?C1000400 1″ 4″ 5 2.57 3.23 P P P P
BHG8?C1000450 1″ 4 1/2″ 5 2.82 3.45 P P P
BHG8?C1000500 1″ 5″ 5 3.07 3.73 P P P P
BHG8?C1000550 1″ 5 1/2″ 5 3.32 3.95 P P P
BHG8?C1000600 1″ 6″ 5 3.57 4.23 P P P
BHG8?C1000650 1″ 6 1/2″ 5 3.82 4.48 P P P
BHG8?C1000700 1″ 7″ 5 4.07 4.73 P P P
BHG8?C1000750 1″ 7 1/2″ 5 4.32 4.90 P P
BHG8?C1000800 1″ 8″ 5 4.57 5.24 P P P
BHG8?C1000850 1″ 8 1/2″ 5 4.84 5.45 P P
BHG8?C1000900 1″ 9″ 5 5.07 5.74 P P P
BHG8?C1000950 1″ 9 1/2″ 5 5.24 P
BHG8?C1001000 1″ 10″ 5 5.57 6.24 P P P
BHG8?C1001100 1″ 11″ 5 6.04 P
BHG8?C1001200 1″ 12″ 5 6.58 7.27 P P
BHG8?C1001300 1″ 13″ 5 7.11 P
BHG8?C1001400 1″ 14″ 5 7.58 P


Hex Bolt Grade 8
Plain / Black
UNC HEX BOLT

GRADE 8 AS2465
Part Size Length Pack BO Wgt Blk BO

(inch) (Kg)
BHG8PC1120250 1 1/8″ 2 1/2″ 5 2.42 P
BHG8PC1120300 1 1/8″ 3″ 5 2.71 P
BHG8PC1120350 1 1/8″ 3 1/2″ 5 3.03 P
BHG8PC1120400 1 1/8″ 4″ 5 3.34 P
BHG8PC1120450 1 1/8″ 4 1/2″ 5 3.66 P
BHG8PC1120500 1 1/8″ 5″ 5 3.98 P
BHG8PC1120550 1 1/8″ 5 1/2″ 5 4.31 P
BHG8PC1120600 1 1/8″ 6″ 5 4.62 P
BHG8PC1120650 1 1/8″ 6 1/2″ 5 4.95 P
BHG8PC1120700 1 1/8″ 7″ 5 5.25 P
BHG8PC1120750 1 1/8″ 7 1/2″ 5 5.70 P
BHG8PC1120800 1 1/8″ 8″ 5 6.00 P
BHG8PC1120900 1 1/8″ 9″ 5 6.75 P
BHG8PC1121000 1 1/8″ 10″ 5 7.65 P
BHG8PC1121100 1 1/8″ 11″ 5 8.40 P
BHG8PC1121200 1 1/8″ 12″ 5 9.15 P
BHG8PC1121400 1 1/8″ 14″ 1 1.94 P
BHG8PC1121600 1 1/8″ 16″ 1 2.20 P
BHG8PC1250300 1 1/4″ 3″ 4 2.80 P
BHG8PC1250350 1 1/4″ 3 1/2″ 4 3.12 P
BHG8PC1250400 1 1/4″ 4″ 4 3.43 P
BHG8PC1250450 1 1/4″ 4 1/2″ 4 3.74 P
BHG8PC1250500 1 1/4″ 5″ 4 4.06 P
BHG8PC1250550 1 1/4″ 5 1/2″ 4 4.37 P
BHG8PC1250600 1 1/4″ 6″ 4 4.68 P
BHG8PC1250650 1 1/4″ 6 1/2″ 4 5.01 P
BHG8PC1250700 1 1/4″ 7″ 4 5.31 P
BHG8PC1250750 1 1/4″ 7 1/2″ 4 5.65 P
BHG8PC1250800 1 1/4″ 8″ 4 5.94 P
BHG8PC1250900 1 1/4″ 9″ 4 6.57 P
BHG8PC1251000 1 1/4″ 10″ 4 7.20 P
BHG8PC1251100 1 1/4″ 11″ 4 7.90 P
BHG8PC1251200 1 1/4″ 12″ 4 8.61 P
BHG8PC1251300 1 1/4″ 13″ 4 8.99 P
BHG8PC1251400 1 1/4″ 13″ 1 2.43 P
BHG8PC1251500 1 1/4″ 15″ 1 2.58 P
BHG8PC1251600 1 1/4″ 16″ 1 2.74 P

45
Hex Bolt Grade 8
Plain / Black
UNC HEX BOLT

GRADE 8 AS2465

(inch) (Kg)
BHG8PC1500300 1 1/2″ 3″ 3 3.30 P
BHG8PC1500350 1 1/2″ 3 1/2″ 3 3.55 P
BHG8PC1500400 1 1/2″ 4″ 3 3.95 P
BHG8PC1500450 1 1/2″ 4 1/2″ 3 4.27 P
BHG8PC1500500 1 1/2″ 5″ 3 4.50 P
BHG8PC1500550 1 1/2″ 5 1/2″ 3 4.95 P
BHG8PC1500600 1 1/2″ 6″ 3 5.30 P
BHG8PC1500650 1 1/2″ 6 1/2″ 3 5.64 P
BHG8PC1500700 1 1/2″ 7″ 3 5.98 P
BHG8PC1500750 1 1/2″ 7 1/2″ 3 6.32 P
BHG8PC1500800 1 1/2″ 8″ 3 6.66 P
BHG8PC1500900 1 1/2″ 9″ 3 7.34 P
BHG8PC1501000 1 1/2″ 10″ 3 8.02 P
BHG8PC1501100 1 1/2″ 11″ 3 8.71 P
BHG8PC1501200 1 1/2″ 12″ 3 9.38 P
BHG8PC1501300 1 1/2″ 13″ 3 10.07 P
BHG8PC1501400 1 1/2″ 14″ 3 10.75 P
BHG8PC1501500 1 1/2″ 15″ 3 11.44 P
BHG8PC1501600 1 1/2″ 16″ 3 12.12 P
BHG8PC1750400 1 3/4″ 4″ 3 5.66 P
BHG8PC1750500 1 3/4″ 5″ 3 6.58 P
BHG8PC1750600 1 3/4″ 6″ 3 7.50 P
BHG8PC1750700 1 3/4″ 7″ 1 2.88 P
BHG8PC1750800 1 3/4″ 8″ 3 9.35 P
BHG8PC1750900 1 3/4″ 9″ 1 3.44 P
BHG8PC1751000 1 3/4″ 10″ 3 11.19 P
BHG8PC2000400 2″ 4″ 2 5.17 P
BHG8PC2000500 2″ 5″ 1 2.97 P
BHG8PC2000600 2″ 6″ 2 6.73 P
BHG8PC2000800 2″ 8″ 2 8.36 P
BHG8PC2001000 2″ 10″ 2 9.95 P
BHG8PC2001200 2″ 12″ 1 5.70 P
BHG8PC2001400 2″ 14″ 1 6.64 P
BHG8PC2001600 2″ 16″ 1 7.46 P

Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?F0250050 1/4″ 1/2″ 200 1.13 P P
BHG8?F0250075 1/4″ 3/4″ 200 1.37 2.06 P P P P
BHG8?F0250100 1/4″ 1″ 200 1.66 2.34 P P P P
BHG8?F0250125 1/4″ 1 1/4″ 200 1.98 P P
BHG8?F0250150 1/4″ 1 1/2″ 200 2.32 3.00 P P P P
BHG8?F0250175 1/4″ 1 3/4″ 200 2.64 P P
BHG8?F0250200 1/4″ 2″ 200 2.97 3.66 P P P P
BHG8?F0250225 1/4″ 2 1/4″ 150 2.47 P P
BHG8?F0250250 1/4″ 2 1/2″ 150 2.72 3.24 P P P P
BHG8?F0250275 1/4″ 2 3/4″ 150 2.97 P P
BHG8?F0250300 1/4″ 3″ 150 3.22 3.73 P P P P
BHG8?F0250350 1/4″ 3 1/2″ 100 2.47 2.82 P P P P
BHG8?F0250400 1/4″ 4″ 100 2.89 3.23 P P P P
BHG8?F0250450 1/4″ 4 1/2″ 100 3.13 P P
BHG8?F0250500 1/4″ 5″ 100 3.46 P P
BHG8?F0250550 1/4″ 5 1/2″ 100 3.79 P P
BHG8?F0250600 1/4″ 6″ 50 2.06 P P
BHG8?F0310050 5/16″ 1/2″ 200 1.90 P P
BHG8?F0310075 5/16″ 3/4″ 200 2.30 3.31 P P P P
BHG8?F0310100 5/16″ 1″ 200 2.70 3.71 P P P P
BHG8?F0310125 5/16″ 1 1/4″ 200 3.21 4.22 P P P P
BHG8?F0310150 5/16″ 1 1/2″ 200 3.73 4.74 P P P P
BHG8?F0310175 5/16″ 1 3/4″ 150 3.18 3.94 P P P P
BHG8?F0310200 5/16″ 2″ 150 3.57 4.32 P P P P
BHG8?F0310225 5/16″ 2 1/4″ 150 3.95 P P
BHG8?F0310250 5/16″ 2 1/2″ 150 4.33 5.09 P P P P
BHG8?F0310275 5/16″ 2 3/4″ 100 3.15 P P
BHG8?F0310300 5/16″ 3″ 100 3.40 3.91 P P P P
BHG8?F0310350 5/16″ 3 1/2″ 100 3.91 4.42 P P P P
BHG8?F0310400 5/16″ 4″ 100 4.43 4.93 P P P P
BHG8?F0310450 5/16″ 4 1/2″ 100 4.94 P P
BHG8?F0310500 5/16″ 5″ 100 5.45 P P
BHG8?F0310550 5/16″ 5 1/2″ 100 5.97 P P
BHG8?F0310600 5/16″ 6″ 100 6.48 P P


47
Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?F0370050 3/8″ 1/2″ 200 2.79 P P
BHG8?F0370075 3/8″ 3/4″ 200 3.39 4.86 P P P P
BHG8?F0370100 3/8″ 1″ 200 3.98 5.45 P P P P
BHG8?F0370125 3/8″ 1 1/4″ 200 4.63 6.10 P P P P
BHG8?F0370150 3/8″ 1 1/2″ 150 4.03 5.14 P P P P
BHG8?F0370175 3/8″ 1 3/4″ 150 4.59 P P
BHG8?F0370200 3/8″ 2″ 100 3.43 4.16 P P P P
BHG8?F0370225 3/8″ 2 1/4″ 100 3.80 P P
BHG8?F0370250 3/8″ 2 1/2″ 100 4.17 4.90 P P P P
BHG8?F0370275 3/8″ 2 3/4″ 100 4.54 P P
BHG8?F0370300 3/8″ 3″ 100 4.91 5.64 P P P P
BHG8?F0370350 3/8″ 3 1/2″ 50 2.82 3.19 P P P P
BHG8?F0370400 3/8″ 4″ 50 3.19 3.56 P P P P
BHG8?F0370450 3/8″ 4 1/2″ 50 3.56 P P
BHG8?F0370500 3/8″ 5″ 50 3.93 4.30 P P P
BHG8?F0370550 3/8″ 5 1/2″ 50 4.30 P P
BHG8?F0370600 3/8″ 6″ 50 4.67 5.04 P P P
BHG8?F0430075 7/16″ 3/4″ 100 2.42 P P
BHG8?F0430100 7/16″ 1″ 100 2.82 4.17 P P P P
BHG8?F0430125 7/16″ 1 1/4″ 100 3.22 P P
BHG8?F0430150 7/16″ 1 1/2″ 100 3.73 5.07 P P P P
BHG8?F0430175 7/16″ 1 3/4″ 100 4.23 P P
BHG8?F0430200 7/16″ 2″ 100 4.74 6.08 P P P P
BHG8?F0430225 7/16″ 2 1/4″ 75 3.93 P P
BHG8?F0430250 7/16″ 2 1/2″ 75 4.31 5.32 P P P P
BHG8?F0430275 7/16″ 2 3/4″ 75 4.69 P P
BHG8?F0430300 7/16″ 3″ 75 5.07 6.08 P P P P
BHG8?F0430350 7/16″ 3 1/2″ 50 3.89 4.56 P P P P
BHG8?F0430400 7/16″ 4″ 50 4.39 5.06 P P P P
BHG8?F0430450 7/16″ 4 1/2″ 50 4.89 P P
BHG8?F0430500 7/16″ 5″ 50 5.40 P P
BHG8?F0430550 7/16″ 5 1/2″ 50 5.90 P P
BHG8?F0430600 7/16″ 6″ 50 6.41 P P


Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
UNF Grade 8
(inch) (Kg) (Kg)
BHG8?F0500075 1/2″ 3/4″ 75 2.90 4.20 P P P
BHG8?F0500100 1/2″ 1″ 75 3.30 4.60 P P P P
BHG8?F0500125 1/2″ 1 1/4″ 75 3.70 5.00 P P P P
BHG8?F0500150 1/2″ 1 1/2″ 75 3.98 5.45 P P P P
BHG8?F0500175 1/2″ 1 3/4″ 75 4.43 5.94 P P P P
BHG8?F0500200 1/2″ 2″ 50 3.30 4.29 P P P P
BHG8?F0500225 1/2″ 2 1/4″ 50 3.75 4.62 P P P P
BHG8?F0500250 1/2″ 2 1/2″ 50 3.90 4.95 P P P P
BHG8?F0500275 1/2″ 2 3/4″ 50 4.41 5.28 P P P P
BHG8?F0500300 1/2″ 3″ 25 2.25 2.80 P P P P
BHG8?F0500325 1/2″ 3 1/4″ 25 2.53 P P
BHG8?F0500350 1/2″ 3 1/2″ 25 2.58 3.13 P P P P
BHG8?F0500400 1/2″ 4″ 25 2.88 3.46 P P P P
BHG8?F0500450 1/2″ 4 1/2″ 25 3.35 3.79 P P P P
BHG8?F0500500 1/2″ 5″ 25 3.68 4.12 P P P P
BHG8?F0500550 1/2″ 5 1/2″ 25 4.01 4.45 P P P P
BHG8?F0500600 1/2″ 6″ 25 4.34 4.78 P P P P
BHG8?F0500650 1/2″ 6 1/2″ 20 3.59 3.94 P P P P
BHG8?F0500700 1/2″ 7″ 20 3.85 4.20 P P P P
BHG8?F0500750 1/2″ 7 1/2″ 20 4.10 4.45 P P P
BHG8?F0500800 1/2″ 8″ 20 4.36 4.71 P P P
BHG8?F0500900 1/2″ 9″ 20 5.05 P
BHG8?F0501000 1/2″ 10″ 20 5.58 P
BHG8?F0501100 1/2″ 11″ 10 3.05 P
BHG8?F0501200 1/2″ 12″ 10 3.32 P


49
Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?F0560100 9/16″ 1″ 25 1.34 P P
BHG8?F0560125 9/16″ 1 1/4″ 25 1.51 P P
BHG8?F0560150 9/16″ 1 1/2″ 25 1.69 2.38 P P P
BHG8?F0560175 9/16″ 1 3/4″ 25 1.89 P P
BHG8?F0560200 9/16″ 2″ 25 2.10 2.80 P P P
BHG8?F0560225 9/16″ 2 1/4″ 25 2.31 P
BHG8?F0560250 9/16″ 2 1/2″ 25 2.52 3.22 P P P
BHG8?F0560275 9/16″ 2 3/4″ 25 2.73 P P
BHG8?F0560300 9/16″ 3″ 25 2.94 3.64 P P P
BHG8?F0560350 9/16″ 3 1/2″ 25 3.35 4.05 P P P
BHG8?F0560400 9/16″ 4″ 25 3.77 4.47 P P P
BHG8?F0560450 9/16″ 4 1/2″ 15 2.51 P P
BHG8?F0560500 9/16″ 5″ 15 2.76 3.18 P P P
BHG8?F0560550 9/16″ 5 1/2″ 15 3.01 P P
BHG8?F0560600 9/16″ 6″ 15 3.26 P P
BHG8?F0620100 5/8″ 1″ 25 1.81 P P
BHG8?F0620125 5/8″ 1 1/4″ 25 2.02 2.88 P P P P
BHG8?F0620150 5/8″ 1 1/2″ 25 2.13 3.09 P P P P
BHG8?F0620175 5/8″ 1 3/4″ 25 2.46 3.33 P P P P
BHG8?F0620200 5/8″ 2″ 25 2.60 3.59 P P P P
BHG8?F0620225 5/8″ 2 1/4″ 25 2.98 3.84 P P P
BHG8?F0620250 5/8″ 2 1/2″ 25 3.08 4.10 P P P P
BHG8?F0620275 5/8″ 2 3/4″ 25 3.49 4.36 P P P
BHG8?F0620300 5/8″ 3″ 25 3.58 4.61 P P P P
BHG8?F0620325 5/8″ 3 1/4″ 25 4.00 P P
BHG8?F0620350 5/8″ 3 1/2″ 25 4.05 5.13 P P P P
BHG8?F0620400 5/8″ 4″ 25 4.55 5.64 P P P P
BHG8?F0620450 5/8″ 4 1/2″ 15 3.03 3.69 P P P
BHG8?F0620500 5/8″ 5″ 15 3.32 4.00 P P P
BHG8?F0620550 5/8″ 5 1/2″ 15 3.79 4.31 P P P
BHG8?F0620600 5/8″ 6″ 15 3.90 4.62 P P P
BHG8?F0620650 5/8″ 6 1/2″ 15 4.31 4.83 P P P
BHG8?F0620700 5/8″ 7″ 15 4.61 5.13 P P P
BHG8?F0620750 5/8″ 7 1/2″ 15 4.91 P P
BHG8?F0620800 5/8″ 8″ 15 5.21 5.73 P P P
BHG8?F0620900 5/8″ 9″ 15 5.95 P
BHG8?F0621000 5/8″ 10″ 15 6.56 P
BHG8?F0621100 5/8″ 11″ 10 4.79 P
BHG8?F0621200 5/8″ 12″ 10 5.10 P


Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
(inch) (Kg) (Kg)
BHG8?F0750100 3/4″ 1″ 25 2.92 P
BHG8?F0750125 3/4″ 1 1/4″ 25 3.22 P
BHG8?F0750150 3/4″ 1 1/2″ 25 3.53 4.90 P P P P
BHG8?F0750175 3/4″ 1 3/4″ 25 3.84 P P
BHG8?F0750200 3/4″ 2″ 25 4.19 5.55 P P P P
BHG8?F0750225 3/4″ 2 1/4″ 25 4.56 5.92 P P P P
BHG8?F0750250 3/4″ 2 1/2″ 20 3.76 5.03 P P P P
BHG8?F0750275 3/4″ 2 3/4″ 20 4.24 P P
BHG8?F0750300 3/4″ 3″ 20 4.32 5.63 P P P P
BHG8?F0750350 3/4″ 3 1/2″ 20 5.13 5.95 P P P P
BHG8?F0750400 3/4″ 4″ 10 2.72 3.41 P P P P
BHG8?F0750450 3/4″ 4 1/2″ 10 3.16 3.70 P P P P
BHG8?F0750500 3/4″ 5″ 10 3.29 4.00 P P P P
BHG8?F0750550 3/4″ 5 1/2″ 10 3.75 4.30 P P P
BHG8?F0750600 3/4″ 6″ 10 3.85 4.59 P P P
BHG8?F0750650 3/4″ 6 1/2″ 10 4.25 P P
BHG8?F0750700 3/4″ 7″ 10 4.53 5.08 P P P
BHG8?F0750750 3/4″ 7 1/2″ 10 4.81 P
BHG8?F0750800 3/4″ 8″ 10 5.10 5.65 P P P
BHG8?F0750900 3/4″ 9″ 5 2.91 3.19 P P P
BHG8?F0751000 3/4″ 10″ 5 3.21 3.48 P P P
BHG8?F0751100 3/4″ 11″ 5 3.51 P
BHG8?F0751200 3/4″ 12″ 5 3.80 P
BHG8?F0751300 3/4″ 13″ 5 4.06 P
BHG8?F0751400 3/4″ 14″ 5 4.31 P


51
Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
Part Size Length Pack BO Wgt Kit Wgt Blk BO Blk Kit ZP BO
(inch) (Kg) (Kg)
BHG8?F0870200 7/8″ 2″ 10 2.43 3.31 P P P
BHG8?F0870225 7/8″ 2 1/4″ 10 2.62 3.49 P P P
BHG8?F0870250 7/8″ 2 1/2″ 10 2.68 3.69 P P P
BHG8?F0870275 7/8″ 2 3/4″ 10 3.02 P P
BHG8?F0870300 7/8″ 3″ 10 3.07 4.10 P P P
BHG8?F0870325 7/8″ 3 1/4″ 10 3.43 P
BHG8?F0870350 7/8″ 3 1/2″ 10 3.63 4.50 P P P
BHG8?F0870400 7/8″ 4″ 10 3.84 4.90 P P P
BHG8?F0870450 7/8″ 4 1/2″ 10 4.22 5.31 P P P
BHG8?F0870500 7/8″ 5″ 10 4.84 5.71 P P P
BHG8?F0870550 7/8″ 5 1/2″ 10 5.24 6.11 P P P
BHG8?F0870600 7/8″ 6″ 10 5.37 6.52 P P P
BHG8?F0870650 7/8″ 6 1/2″ 5 2.98 3.42 P P P
BHG8?F0870700 7/8″ 7″ 5 3.17 3.61 P P P
BHG8?F0870750 7/8″ 7 1/2″ 5 3.36 P
BHG8?F0870800 7/8″ 8″ 5 3.55 P P
BHG8?F0870850 7/8″ 8 1/2″ 5 3.83 P
BHG8?F0870900 7/8″ 9″ 5 4.03 P
BHG8?F0871000 7/8″ 10″ 5 4.44 P
BHG8?F0871200 7/8″ 12″ 5 5.17 P


Zinc Plate
Plain / Black
UNF HEX BOLT & NUT

GRADE 8 AS2465
Part Size Length Pack BO Wgt Kit Wgt Blk BO Blk Kit ZP BO
1″-14 TPI (inch) (Kg) (Kg)
BHG8?F1000200F 1″ 2″ 5 1.67 2.33 P P P
BHG8?F1000225F 1″ 2 1/4″ 5 1.78 P P
BHG8?F1000250F 1″ 2 1/2″ 5 1.90 2.57 P P P
BHG8?F1000275F 1″ 2 3/4″ 5 2.04 P
BHG8?F1000300F 1″ 3″ 5 2.17 2.83 P P P
BHG8?F1000350F 1″ 3 1/2″ 5 2.43 3.09 P P P
BHG8?F1000400F 1″ 4″ 5 2.69 3.36 P P P
BHG8?F1000450F 1″ 4 1/2″ 5 2.96 3.62 P P P
BHG8?F1000500F 1″ 5″ 5 3.22 3.88 P P P
BHG8?F1000550F 1″ 5 1/2″ 5 3.48 4.15 P P P
BHG8?F1000600F 1″ 6″ 5 3.75 4.41 P P P
BHG8?F1000650F 1″ 6 1/2″ 5 3.98 4.64 P P P
BHG8?F1000700F 1″ 7″ 5 4.22 4.88 P P P
BHG8?F1000750F 1″ 7 1/2″ 5 4.48 P
BHG8?F1000800F 1″ 8″ 5 4.74 5.40 P P P
BHG8?F1000850F 1″ 8 1/2″ 5 5.06 P
BHG8?F1000900F 1″ 9″ 5 5.33 5.99 P P P
BHG8?F1000950F 1″ 9 1/2″ 5 5.59 P
BHG8?F1001000F 1″ 10″ 5 5.85 6.51 P P P
BHG8?F1001100F 1″ 11″ 5 6.43 P
BHG8?F1001200F 1″ 12″ 5 6.97 P
BHG8?F1120300 1 1/8″ 3″ 5 2.70 P
BHG8?F1120350 1 1/8″ 3 1/2″ 5 3.11 P
BHG8?F1120400 1 1/8″ 4″ 5 3.43 P
BHG8?F1120450 1 1/8″ 4 1/2″ 5 3.75 P
BHG8?F1120500 1 1/8″ 5″ 5 4.04 P
BHG8?F1120550 1 1/8″ 5 1/2″ 5 4.36 P
BHG8?F1120600 1 1/8″ 6″ 5 4.65 P
BHG8?F1120650 1 1/8″ 6 1/2″ 5 5.20 P
BHG8?F1120700 1 1/8″ 7″ 5 5.27 P
BHG8?F1120750 1 1/8″ 7 1/2″ 5 5.85 P
BHG8?F1120800 1 1/8″ 8″ 3 3.53 P
BHG8?F1120900 1 1/8″ 9″ 1 1.30 P
BHG8?F1121000 1 1/8″ 10″ 3 4.26 P


53
Hex Bolt Grade 8
Plain / Black
UNF HEX BOLT

GRADE 8 AS2465

(inch) (Kg)
BHG8PF1250300 1 1/4″ 3″ 5 3.67 P
BHG8PF1250350 1 1/4″ 3 1/2″ 5 4.04 P
BHG8PF1250400 1 1/4″ 4″ 5 4.43 P
BHG8PF1250450 1 1/4″ 4 1/2″ 5 4.81 P
BHG8PF1250500 1 1/4″ 5″ 5 5.20 P
BHG8PF1250550 1 1/4″ 5 1/2″ 5 5.56 P
BHG8PF1250600 1 1/4″ 6″ 5 5.95 P
BHG8PF1250650 1 1/4″ 6 1/2″ 5 6.63 P
BHG8PF1250700 1 1/4″ 7″ 5 6.70 P
BHG8PF1250750 1 1/4″ 7 1/2″ 5 7.41 P
BHG8PF1250800 1 1/4″ 8″ 3 4.47 P
BHG8PF1250900 1 1/4″ 9″ 3 4.93 P
BHG8PF1251000 1 1/4″ 10″ 1 1.79 P
BHG8PF1500450 1 1/2″ 4 1/2″ 5 7.11 P
BHG8PF1500500 1 1/2″ 5″ 3 4.51 P
BHG8PF1500600 1 1/2″ 6″ 3 5.28 P
BHG8PF1500900 1 1/2″ 9″ 2 4.90 P
BHG8PF1501000 1 1/2″ 10″ 2 5.35 P

High Tensile
High Quality
High Availability
[ Free Download -
NATA & Test Certificates on-line.]
[ ALL High Tensile product

Test Certificates are on-line. ]
Select Product Group: Enter Heat Number:
Grade 8 Bolts & Nuts 6607010148 Go

»
Open a file by clicking on either the PDF icon or the Heat Number.
PDF 6607010148
BHG8PF0500175
G8 BLK HEX BO: 1/2UNF X 1-3/4 Free NATA Report for
89.0Kb this item
Go
AS1110 Class 10.9
Features
P Forged Head
P High Quality Steel
P Rolled Thread†
P DIN934 Class 10 Nut see pg 8
P DIN980 Cone Locking Nut see pg 8
P Sampson Washers see pg 12
Precision Hex Bolts
40% Higher Clamp Load than Class 8.8
† Some non-preferred lengths are cut threads.

If rolled threads are required, please state this on the order.
Hex Bolt Class 10.9
Plain / Black
HEX BOLT
CLASS 10.9 AS1110.1

(mm) (mm) (Kg) PLN
BH10PCM160030 M16 30 30 25 2.13 P
BH10PCM160035 M16 35 35 25 2.30 P
BH10PCM160040 M16 40 40 25 2.50 P
BH10PCM160045 M16 45 38 25 2.70 P
BH10PCM160050 M16 50 38 25 2.88 P
BH10PCM160055 M16 55 38 25 3.08 P
BH10PCM160060 M16 60 38 25 3.28 P
BH10PCM160065 M16 65 38 25 3.45 P
BH10PCM160070 M16 70 38 25 3.65 P
BH10PCM160075 M16 75 38 25 3.85 P
BH10PCM160080 M16 80 38 25 4.03 P
BH10PCM160090 M16 90 38 25 4.43 P
BH10PCM160100 M16 100 38 25 4.80 P
BH10PCM160110 M16 110 38 15 3.11 P
BH10PCM160120 M16 120 38 15 3.35 P
BH10PCM160130 M16 130 44 15 3.57 P
BH10PCM160140 M16 140 44 15 3.80 P
BH10PCM160150 M16 150 44 15 4.04 P

57
Hex Bolt Class 10.9
Plain / Black
HEX BOLT
CLASS 10.9 AS1110.1

(mm) (mm) (Kg) PLN
BH10PCM200040 M20 40 40 25 4.30 P
BH10PCM200045 M20 45 45 25 4.60 P
BH10PCM200050 M20 50 46 25 4.90 P
BH10PCM200055 M20 55 46 25 5.20 P
BH10PCM200060 M20 60 46 25 5.50 P
BH10PCM200065 M20 65 46 20 4.64 P
BH10PCM200070 M20 70 46 20 4.88 P
BH10PCM200075 M20 75 46 20 5.12 P
BH10PCM200080 M20 80 46 20 5.36 P
BH10PCM200085 M20 85 46 20 5.60 P
BH10PCM200090 M20 90 46 20 5.84 P
BH10PCM200100 M20 100 46 10 3.16 P
BH10PCM200110 M20 110 46 10 3.40 P
BH10PCM200120 M20 120 46 10 3.64 P
BH10PCM200130 M20 130 52 10 3.88 P
BH10PCM200140 M20 140 52 10 4.12 P
BH10PCM200150 M20 150 52 10 4.36 P
BH10PCM200160 M20 160 52 10 4.60 P
BH10PCM200180 M20 180 52 10 5.08 P
BH10PCM200200 M20 200 52 10 5.56 P
BH10PCM200220 M20 220 65 10 6.04 P
BH10PCM200230 M20 230 65 10 6.28 P
BH10PCM200240 M20 240 65 10 6.52 P
BH10PCM200250 M20 250 65 10 6.76 P
BH10PCM200260 M20 260 65 10 7.00 P
BH10PCM200280 M20 280 65 10 7.48 P
BH10PCM200300 M20 300 65 10 7.96 P

Hex Bolt Class 10.9
Plain / Black
HEX BOLT
CLASS 10.9 AS1110.1

(mm) (mm) (Kg) PLN
BH10PCM220070 M22 70 50 5 1.41 P
BH10PCM220080 M22 80 50 5 1.56 P
BH10PCM220100 M22 100 50 5 1.85 P
BH10PCM220150 M22 150 56 5 2.55 P
BH10PCM220190 M22 190 56 5 3.15 P
BH10PCM220200 M22 200 56 5 3.30 P
BH10PCM240050 M24 50 50 5 1.52 P
BH10PCM240055 M24 55 55 5 1.61 P
BH10PCM240060 M24 60 60 5 1.69 P
BH10PCM240065 M24 65 54 5 1.78 P
BH10PCM240070 M24 70 54 5 1.87 P
BH10PCM240075 M24 75 54 5 1.95 P
BH10PCM240080 M24 80 54 5 2.04 P
BH10PCM240090 M24 90 54 5 2.21 P
BH10PCM240100 M24 100 54 5 2.39 P
BH10PCM240110 M24 110 54 5 2.56 P
BH10PCM240120 M24 120 54 5 2.73 P
BH10PCM240130 M24 130 60 5 2.91 P
BH10PCM240140 M24 140 60 5 3.08 P
BH10PCM240150 M24 150 60 5 3.26 P
BH10PCM240160 M24 160 60 5 3.43 P
BH10PCM240170 M24 170 60 5 3.60 P
BH10PCM240180 M24 180 60 5 3.78 P
BH10PCM240190 M24 190 60 5 3.95 P
BH10PCM240200 M24 200 60 5 4.12 P
BH10PCM240220 M24 220 73 5 4.47 P
BH10PCM240230 M24 230 73 5 4.64 P
BH10PCM240240 M24 240 73 5 4.82 P
BH10PCM240250 M24 250 73 5 4.99 P
BH10PCM240260 M24 260 73 5 5.16 P
BH10PCM240280 M24 280 73 5 5.51 P
BH10PCM240300 M24 300 73 5 5.86 P

59
Hex Bolt Class 10.9
Plain / Black
HEX BOLT
CLASS 10.9 AS1110.1

(mm) (mm) (Kg) PLN
BH10PCM270080 M27 80 60 5 2.70 P
BH10PCM270100 M27 100 60 5 3.14 P
BH10PCM270110 M27 110 60 5 3.36 P
BH10PCM270120 M27 120 60 5 3.58 P
BH10PCM270130 M27 130 66 5 3.80 P
BH10PCM270170 M27 170 66 5 4.68 P
BH10PCM270180 M27 180 66 5 4.73 P
BH10PCM300050 M30 50 50 5 2.68 P
BH10PCM300055 M30 55 55 5 2.82 P
BH10PCM300060 M30 60 60 5 2.95 P
BH10PCM300065 M30 65 65 5 3.09 P
BH10PCM300070 M30 70 66 5 3.23 P
BH10PCM300075 M30 75 66 5 3.36 P
BH10PCM300080 M30 80 66 5 3.50 P
BH10PCM300085 M30 85 66 5 3.63 P
BH10PCM300090 M30 90 66 5 3.77 P
BH10PCM300100 M30 100 66 5 4.04 P
BH10PCM300110 M30 110 66 5 4.32 P
BH10PCM300120 M30 120 66 5 4.59 P
BH10PCM300130 M30 130 72 5 4.86 P
BH10PCM300140 M30 140 72 5 5.13 P
BH10PCM300150 M30 150 72 5 5.41 P
BH10PCM300160 M30 160 72 5 5.68 P
BH10PCM300170 M30 170 72 5 5.95 P
BH10PCM300180 M30 180 72 5 6.22 P
BH10PCM300200 M30 200 72 5 6.77 P
BH10PCM300210 M30 210 85 5 7.04 P
BH10PCM300220 M30 220 85 5 7.31 P
BH10PCM300230 M30 230 85 5 7.59 P
BH10PCM300240 M30 240 85 5 7.86 P
BH10PCM300250 M30 250 85 5 8.13 P
BH10PCM300270 M30 270 85 5 8.68 P
BH10PCM300275 M30 275 85 5 8.81 P
BH10PCM300280 M30 280 85 5 8.95 P
BH10PCM300300 M30 300 85 1 1.86 P
BH10PCM330100 M33 100 72 1 0.95 P
BH10PCM330160 M33 160 78 1 1.35 P
BH10PCM330180 M33 180 78 1 1.48 P
BH10PCM330260 M33 260 91 1 2.02 P
BH10PCM330300 M33 300 91 1 2.29 P

Hex Bolt Class 10.9
Plain / Black
HEX BOLT
CLASS 10.9 AS1110.1

(mm) (mm) (Kg) PLN
BH10PCM360075 M36 75 75 2 2.09 P
BH10PCM360080 M36 80 80 2 2.16 P
BH10PCM360090 M36 90 78 2 2.32 P
BH10PCM360100 M36 100 78 2 2.48 P
BH10PCM360110 M36 110 78 2 2.64 P
BH10PCM360120 M36 120 78 2 2.80 P
BH10PCM360130 M36 130 84 2 2.95 P
BH10PCM360140 M36 140 84 2 3.11 P
BH10PCM360150 M36 150 84 2 3.27 P
BH10PCM360160 M36 160 84 2 3.43 P
BH10PCM360165 M36 165 84 2 3.50 P
BH10PCM360170 M36 170 84 2 3.58 P
BH10PCM360180 M36 180 84 2 3.74 P
BH10PCM360190 M36 190 84 2 3.90 P
BH10PCM360200 M36 200 84 2 4.06 P
BH10PCM360210 M36 210 97 2 4.21 P
BH10PCM360240 M36 240 97 2 4.69 P
BH10PCM360250 M36 250 97 2 4.84 P
BH10PCM360260 M36 260 97 2 5.00 P
BH10PCM360280 M36 280 97 2 5.32 P
BH10PCM360285 M36 285 97 2 5.40 P
BH10PCM360290 M36 290 97 2 5.47 P
BH10PCM360300 M36 300 97 2 5.63 P
BH10PCM360320 M36 320 97 2 5.95 P
BH10PCM420130 M42 130 96 1 1.95 P
BH10PCM420150 M42 150 96 1 2.16 P
BH10PCM420160 M42 160 96 1 2.27 P
BH10PCM420180 M42 180 96 1 2.48 P
BH10PCM420200 M42 200 96 1 2.69 P
BH10PCM420220 M42 220 109 1 2.91 P
BH10PCM420230 M42 230 109 1 3.02 P
BH10PCM420240 M42 240 109 1 3.12 P
BH10PCM420250 M42 250 109 1 3.23 P
BH10PCM420270 M42 270 109 1 3.44 P
BH10PCM420300 M42 300 109 1 3.77 P
BH10PCM420340 M42 340 109 1 4.19 P
BH10PCM480180 M48 180 108 1 3.43 P
BH10PCM480190 M48 190 108 1 3.58 P
BH10PCM480200 M48 200 108 1 3.73 P
BH10PCM480220 M48 220 121 1 4.03 P
BH10PCM480250 M48 250 121 1 4.47 P
BH10PCM480260 M48 260 121 1 4.62 P

61
Plow Bolt Grade 9
Plain / Black
UNC PLOW BOLT

GRADE 9 HOBSON STANDARD
Part Alternate OEM Size Length Pack Pack Wgt Stock

Part Part
(inch) (Kg) PLN
CBPG9PC0620150 821001 4F3664 5/8″ 1 1/2″ 200 14.60 P
CBPG9PC0620175 821003 4F3653 5/8″ 1 3/4″ 200 16.20 P
CBPG9PC0620200 821005 4F3654 5/8″ 2″ 175 15.58 P
CBPG9PC0620225 821007 3F5108 5/8″ 2 1/4″ 150 14.55 P
CBPG9PC0620250 821009 4F3656 5/8″ 2 1/2″ 125 13.63 P
CBPG9PC0620275 821011 4F3657 5/8″ 2 3/4″ 100 11.90 P
CBPG9PC0620300 821013 4F3658 5/8″ 3″ 100 12.90 P
CBPG9PC0620350 821017 4F3665 5/8″ 3 1/2″ 85 12.58 P
CBPG9PC0620400 821021 4F3671 5/8″ 4″ 70 11.76 P
CBPG9PC0620450 821025 - 5/8″ 4 1/2″ 60 11.10 P
CBPG9PC0750200 821205 4F3672 3/4″ 2″ 115 15.30 P
CBPG9PC0750225 821207 4F7827 3/4″ 2 1/4″ 100 14.50 P
CBPG9PC0750250 821209 5J4773 3/4″ 2 1/2″ 90 14.04 P
CBPG9PC0750275 821211 5J4771 3/4″ 2 3/4″ 80 13.76 P
CBPG9PC0750300 821213 4F0138 3/4″ 3″ 80 14.88 P
CBPG9PC0750325 821215 - 3/4″ 3 1/4″ 70 14.07 P
CBPG9PC0750350 821217 - 3/4″ 3 1/2″ 70 14.98 P
CBPG9PC0750375 821219 5F8933 3/4″ 3 3/4″ 60 13.68 P
CBPG9PC0750400 821221 - 3/4″ 4″ 55 13.37 P
CBPG9PC0750450 821225 4F0253 3/4″ 4 1/2″ 40 10.84 P
CBPG9PC0750500 821229 - 3/4″ 5″ 40 12.00 P
CBPG9PC0870225 821407 - 7/8″ 2 1/4″ 75 15.23 P
CBPG9PC0870250 821409 5J4772 7/8″ 2 1/2″ 65 14.17 P
CBPG9PC0870275 821411 6F0196 7/8″ 2 3/4″ 60 14.10 P
CBPG9PC0870300 821413 5J2409 7/8″ 3″ 55 13.81 P
CBPG9PC0870325 821415 8J2935 7/8″ 3 1/4″ 50 13.70 P
CBPG9PC0870350 821417 2J2548 7/8″ 3 1/2″ 45 13.32 P
CBPG9PC0870400 821421 - 7/8″ 4″ 45 15.08 P
CBPG9PC0870425 821423 2J5458 7/8″ 4 1/4″ 40 14.16 P
CBPG9PC0870500 821429 - 7/8″ 5″ 35 14.32 P
CBPG9PC1000275 821611 1J5607 1″ 2 3/4″ 45 14.22 P
CBPG9PC1000300 821613 4F4042 1″ 3″ 40 13.88 P
CBPG9PC1000325 821615 4J9058 1″ 3 1/4″ 40 14.92 P
CBPG9PC1000350 821617 4J9208 1″ 3 1/2″ 35 13.93 P
CBPG9PC1000375 821619 1J4948 1″ 3 3/4″ 30 12.54 P
CBPG9PC1000400 821621 5P8136 1″ 4″ 30 13.14 P
CBPG9PC1000450 821625 1J3527 1″ 4 1/2″ 25 12.28 P
CBPG9PC1000500 821629 1J2034 1″ 5″ 20 10.66 P
CBPG9PC1000550 - - 1″ 5 1/2″ 20 11.70 P

Plow Bolt Grade 9
Plain / Black
UNC PLOW BOLT

Part Alternate OEM Size Length Pack Pack Wgt Stock

Part Part
(inch) (Kg) PLN
CBPG9PC1250375 822019 6V6535 1 1/4″ 3 3/4″ 15 10.59 P
CBPG9PC1250387 822020 5P8823 1 1/4″ 3 7/8″ 15 10.80 P
CBPG9PC1250400 822021 - 1 1/4″ 4″ 15 11.10 P
CBPG9PC1250412 822022 - 1 1/4″ 4 1/8″ 15 11.30 P
CBPG9PC1250450 822025 6V8360 1 1/4″ 4 1/2″ 15 12.09 P
CBPG9PC1250500 822029 5P8361 1 1/4″ 5″ 15 13.05 P
CBPG9PC1250600 822037 - 1 1/4″ 6″ 15 15.12 P
CBPG9PC1370450 - - 1 3/8″ 4 1/2″ 10 8.80 P
CBPG9PC1370550 - - 1 3/8″ 5 1/2″ 10 10.80 P
CBPG9PC1370600 - - 1 3/8″ 6″ 10 14.80 P
UNC PLOW HEX NUT

Part Alternate OEM Size Pack Pack Wgt Stock

Part Part
(Kg) PLN
CNPG8PC062 960410 4K0367 5/8″ 400 12.80 P
CNPG8PC075 960412 2J3506 3/4″ 250 13.00 P
CNPG8PC087 960414 2J3505 7/8″ 150 12.30 P
CNPG8PC100 960416 2J3507 1″ 100 12.10 P
CNPG8PC125 960420 3K9770 1 1/4″ 50 11.90 P
CNPG8PC137 - - 1 3/8″ 50 8.90 P

63
Technical
Thread Table
PITCH (MM) THREADS PER INCH
Size Coarse Fine Extra Fine UNC UN8 UNF BSW BSF
M1.6 - #0 0.35 - - - - 80 - -
M2 - #1 0.4 - - - - 72 - -
- - #2 - - - 56 - 64 - -
M2.5 - #3 0.45 - - 48 - 56 - -
- - #4 - - - 40 - 48 - -
M3 1/8″ #5 0.5 - - 40 - 44 40 -
M3.5 - #6 0.6 - - 32 - 40 - -
M4 - #8 0.7 - - 32 - 36 - -
M5 3/16″ #10 0.8 - - 24 - 32 24 32
- - #12 - - - 24 - 28 - -
M6 1/4″ - 1 - - 20 - 28 20 26
M8 5/16″ - 1.25 1 - 18 - 24 18 22
M10 3/8″ - 1.5 1.25 1 16 - 24 16 20
- 7/16″ - - - - 14 - 20 14 18
M12 1/2″ - 1.75 1.5 1.25 13 - 20 12 16
M14 9/16″ - 2 1.5 - 12 - 18 12 16
M16 5/8″ - 2 1.5 - 11 - 18 11 14
M18 - - 2.5 1.5 - - - - - -
M20 3/4″ - 2.5 1.5 - 10 - 16 10 12
M22 7/8″ - 2.5 1.5 - 9 - 14 9 11
M24 1″ - 3 2 - 8 8 12 (14) 8 10
M27 1 1/8″ - 3 2 - 7 8 12 7 9
M30 1 1/4″ - 3.5 2 - 7 8 12 7 9
M33 1 3/8″ - 3.5 2 - 6 8 12 6 8
M36 1 1/2″ - 4 3 - 6 8 12 6 8
M39 1 5/8″ - 4 3 - - 8 - 5 8
M42 - - 4.5 - - - - - - -
M45 1 3/4″ - 4.5 - - 5 8 - 5 7
M48 1 7/8″ - 5 - - - 8 - - -
M52 2″ - 5 - - 4.5 8 - 4.5 7
M56 2 1/4″ - 5.5 - - 4.5 8 - 4 6
M60 - - 5.5 - - - - - - -
M64 2 1/2″ - 6 - - 4 8 - 4 6
M72 2 3/4″ - 6 - - 4 8 - 3.5 6
M80 3″ - 6 - - 4 8 - 3.5 5
- 3 1/4″ - - - - 4 8 - 3.25 5
M90 3 1/2″ - 6 - - 4 8 - 3.25 4.5
- 3 3/4″ - - - - 4 8 - 3 4.5
M100 4″ - 6 - - 4 8 - 3 4.5
64 Since 1935 ...because quality matters April 2011

Terms and Conditions
The Company and the Customer each agree with the other as follows:
DEFINITIONS
Company means Hobson Engineering Pty Limited (A.B.N. 38 000 289 958).
Customer means the party described as the customer in the Delivery Docket as amended by the Invoice.
Delivery Docket means the document furnished by the Company to the Customer.
GST has the same meaning as given in A New Tax System (Goods and Services Tax) Act 1999 (“Act”).
Invoice means a tax invoice (as defined in the Act) furnished by the Company to the Customer in respect of the product.
Product means the goods described as the product in the Delivery Docket as amended by the Invoice.
Purchase Order means the request by the Customer for the Product which is accepted by the Company.
Sum means the price and other monies payable for the Product together with GST payable on the supply of the Product.
SUPPLY
The Company supplies to the Customer the Product in accordance with these terms and conditions as varied in writing by the Company. Any
variation in writing by the Company shall take precedence to these terms and conditions. We reserve the right to supply 316 stainless steel in
lieu of 304 stainless steel.
PRICE
The Sum is set forth in the Purchase Order as amended by the Invoice. The Customer agrees that the Sum set forth in the Purchase Order may
be amended by the Invoice in respect of the following:
arithmetic error; and
GST payable on the supply of the Product not included or incorrectly calculated in the Sum.
In addition to the price the Customer agrees, if so requested by the Company, to pay:
any increase in any GST taxes and duties which the Company may be required to collect or pay in respect of the Product after the date of the
Delivery Docket; and
interest accruing on a daily basis on the unpaid balance of the Sum from the due date for payment until actual receipt at the rate of 1 per cent
per month.
PAYMENT
The Customer must pay the Sum within 30 days of the end of the month in which the Product is delivered to the Customer unless otherwise
determined by the Company.
TITLE AND RISK
Notwithstanding any other term and condition, the parties agree that the risk of the Product passes on delivery, but title to the Product does
not pass until the Sum is paid in full. Until such time as the Sum is paid in full the Customer is only at liberty to sell the Product in the ordinary
course of its business as agent for the Company on the condition that it holds on trust and accounts to the Company for the proceeds thereof.
Pending the passing of title to the Product the Company may require the Customer to mark the Product as being the property of the Company.
ACCEPTANCE
The initialling or signing of the Delivery Docket by the Customer or representative of the Customer shall constitute acceptance of the Product in
accord with these terms and conditions.
RETURNS AND ALLOWANCES
The Customer must satisfy itself within 14 days of the date of delivery of the Product with the type and quantity of the Product. In the event that
the Customer considers it has not received the appropriate type and or quantity of Product it must notify the Company in writing within 14 days
of the date of delivery of the Product. The notice must refer to the Delivery Docket number, the delivery date, the invoice number (if applicable)
and provide adequate details of the incorrect type and or quantity of Product.
As a consequence of this condition the receipt of Products by the Company, returned by the Customer does not constitute acceptance of
the Product. Acceptance by the Company shall only be given by the Company, in writing, after the Product has been inspected and found
satisfactory in the opinion of the Company. In the event that the Company does not accept the Product the Customer will be notified and the
Product made available to the Customer. As a consequence of this condition no transport or freight costs shall be borne by the Company unless
agreed to in writing by the Company.
EXCLUSION OF WARRANTY
Nothing in this agreement excludes, restricts or modifies any condition, warranty or liability which may at any time be implied by the Trade
Practices Act or Sales of Goods Act (NSW) or equivalent State or Territory legislation or any other law where to do so is illegal or would render
any provision of this agreement void.
Where the Company is responsible pursuant to the aforesaid condition warranty or liability which can not be excluded the parties agree that
the Company shall only be liable for the cost of repair or the resupply of the Product. Subject to this condition any express or implied condition,
statement or warranty (statutory or otherwise) in respect of the Product is expressly negated and excluded.
GENERAL
The validity, interpretation and performance of this agreement will be governed by and construed in accordance with the law of the State of New
South Wales and of the Commonwealth of Australia which the parties acknowledge is the proper law of this agreement. Each of the parties
irrevocably agrees that the Courts of the State of New South Wales and of the Commonwealth of Australia will have jurisdiction to hear and
determine any suit, action or proceedings, and to settle any dispute, which may arise out of or in connection with this agreement and for this
purpose irrevocably submits to the jurisdiction of such Courts.
DISCOUNTS as advised are applicable to the prices shown in this price list.
PRICES The resale prices or discounts referred to in the price list are recommended only and there is no obligation to comply with the
recommendation. Prices are subject to GST where applicable.
Minimum invoice value is $40.00
SHIPPING QUANTITIES On specially manufactured items (± 10%).
VALIDITY ON SPECIAL QUOTATIONS 14 days unless otherwise stated.
© Copyright 2005 – No part of this catalogue may be published without the written consent of the publishers.
Note: Due to research and development, products are continually improved. This may lead to the specifications being changed without notice.
As part of our ongoing commitment to serve your fastener needs, please let us know if there are any products which we lack.
Also, if you’ve got any comments on this year’s Catalogue, let us know. We’ll consider your feedback when we produce next year’s. This
catalogue is for you to use – so if it’s use can be made easier, then make sure you tell us! Our aim is to have the best catalogue possible as well
as the best products.
April 2011 Since 1935 ...because quality matters

High Tensile Stock List

Uploaded by

Copyright:

Available Formats

High Tensile Stock List

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

High Tensile Stock List

Uploaded by

Copyright:

Available Formats

What products does the company offer?

What products does the company offer?

What are the company's terms and conditions of sale?

What are the company's terms and conditions of sale?

High Tensile

Stock List 2011

Quality Fasteners Since 1935

Sydney Brisbane Melbourne Perth

email: [email protected] email: [email protected] email: [email protected] email: [email protected]

Tasmania Agent www.hobson.com.au

Mornington Tas 7018

Ph: (03) 6244 7455

Fax: (03) 6244 7317

Published by Hobson Engineering Co. Pty. Ltd.

Look out for other released Hobson Publications.

Since 1935 ...because quality matters April 2011

Class 8 Hex Nuts 6

Grade 2, 5 & 8 Hex Nuts 10

Class 8.8 Hex Set Screws 24

Plow Bolts & Nuts 62

Technical Thread Table 64

April 2011 Quality Fasteners Since 1935 1

Part Size Pack Pack Wgt Stock

METRIC SAMPSONROD™ 3MTR

Part Size Pack Pack Wgt Stock

2 Quality Fasteners Since 1935 April 2011

METRIC FINE PITCH SAMPSONROD™ 1MTR

Part Size Pitch Pack Pack Wgt Stock

UNC SAMPSONROD™ 3FT

Part Size Pack Pack Wgt Stock

UN8 SAMPSONROD™ 3FT

Part Size Pack Pack Wgt Stock

April 2011 Quality Fasteners Since 1935

UNF SAMPSONROD™ 3FT

Part Size TPI Pack Pack Wgt Stock

BSF SAMPSONROD™ 3FT

Part Size TPI Pack Pack Wgt Stock

BSW SAMPSONROD™ 3FT

Part Size TPI Pack Pack Wgt Stock

4 Quality Fasteners Since 1935 April 2011

METRIC HOBROD™ 1mtr

Part Size Pack Pack Wgt Stock

UNC HOBROD™ 3FT

Part Size Pack Pack Wgt Stock

STARTER BAR ( L BOLT )

Part A L D T Pack Pack Wgt Stock

April 2011 Quality Fasteners Since 1935

FASCIA HEX BOLT & NUT KIT

PURLIN HEX FLANGE BOLT & NUT KIT

METRIC HEX NUT

METRIC HEX LOCK NUT

6 Quality Fasteners Since 1935 April 2011

METRIC NYLON INSERT HEX NUT

METRIC FINE PITCH NYLON INSERT HEX NUT

STRUCTURAL HEX NUTS

Part Size Pack Pack Wgt Stock

April 2011 Quality Fasteners Since 1935

METRIC HEX NUT

Part Size Pack Pack Wgt Stock