SPEC. SHEET No.

GT-600E-1-00301/EX-21
DATE October, 2014

TADANO TRUCK CRANE

MODEL : GT-600EX
( CARRIER : TC-4255-2 / EURO-3 )

GENERAL DATA

CRANE CAPACITY 60,000 kg at 3.0 m

BOOM 5-section, 11.0 m – 43.0 m

DIMENSION
Overall length approx. 13,170 mm
Overall width approx. 2,820 mm
Overall height approx. 3,730 mm

MASS
Kilograms
Total Front Rear
Base machine with 300 L fuel 41,500 16,000 25,500
Remove
1 5.6 t hook ball -150 75 -225
2 Top Jib (6.4 m) -225 -200 -25
3 Base Jib (8.8 m) -500 -550 50
4 Single Top (Auxiliary boom sheave) -50 -100 50
5 Spare Tire -125 -110 -15
6 Spare Tire Bracket -25 -20 -5
7 35 t hook block -410 -700 290
8 Counter weight and pins -4,380 1,960 -6,340
Add
9 60 t hook block 570 970 -400
10 2 Persons 150 200 -50
11 Additional Oil Cooler (Option) 60 -25 85

Permissible Axle load 42,150 16,480 25,670

PERFORMANCE
Max. travelling speed computed 84 km/h
Gradeability (tan q) computed 58 %

Specifications are subject to change without notice.

-1-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

CRANE SPECIFICATIONS

MODEL GT-600EX
CAPACITY 60,000 kg at 3.0 m
BOOM Five-section full power partially synchronized telescoping boom
of round box construction with 5 sheaves at boom head.
The synchronization system consists of 2 telescope cylinders,
extension cables and retraction cables. Selection of 2 boom
telescoping modes.
Hydraulic cylinders fitted with holding valves.
Fully retracted length ------ 11.0 m
Fully extended length ----- 43.0 m
Extension speed ------------ 32.0 m in 135s
JIB Two-staged swingaround boom extension. Triple offset (5o/ 25o/
45o) type. Stores alongside base boom section.
Assistant cylinders for mounting and stowing.
Single sheave at jib head.
Length ------------------------- 8.8 m and 15.2 m
SINGLE TOP (AUXILIARY Single sheave.
BOOM SHEAVE) Mounted to main boom head for single line work.
ELEVATION By a double-acting hydraulic cylinder, fitted with holding valve.
Elevation speed -------------- –2o to 81o in 76s

HOIST – Main winch Variable speed type with grooved drum driven by hydraulic
axial piston motor through winch speed reducer. Power load
lowering and hoisting.
Equipped with automatic brake (Neutral brake) and counterbalance
valve.
Controlled independently of auxiliary winch.
Single line pull ---------------- 54.9 kN {5,600 kgf}
Single line speed ------------ 139 m/min. (at the 4th layer)
Wire rope ---------------------- Spin-resistant type
Diameter x length ---------19 mm x 235 m
HOIST– Variable speed type with grooved drum driven by hydraulic
Auxiliary winch axial piston motor through winch speed reducer. Power load
lowering and hoisting.
Equipped with automatic brake (Neutral brake) and counterbalance
valve.
Controlled independently of main winch.
Single line pull ---------------- 54.9 kN {5,600 kgf}
Single line speed -------------121 m/min. (at the 2nd layer)
Wire rope ---------------------- Spin-resistant type
Diameter x length ---------19 mm x 127 m
SLEWING Hydraulic axial piston motor driven through planetary slewing speed
reducer. Continuous 360o full circle slewing on ball bearing
slew ring.
Equipped with manually locked/released slewing brake.
Slewing speed ------------- 1.7 min-1{rpm}

-2-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

HYDRAULIC SYSTEM Pumps ----------------- Two variable piston pumps for telescoping,
elevating and winches.
Tandem gear pump for slewing and optional
equipment.
Control valves ------- Multiple valves actuated by pilot pressure
with integral pressure relief valves.
Circuit ------------------ Equipped with air cooled type oil cooler.
Oil pressure appears on AML display for
main circuit.
Hydraulic oil tank capacity -----
approx. 690 liters
Filters ------------------ Return line filter
CRANE CONTROL By 4 control levers for slewing, boom hoist, main winch, boom
telescoping or auxiliary winch with 2 control pedals for boom
hoist and boom telescoping based on ISO standard layout.
Control lever stands can change neutral positions and tilt for
easy access to cab.
CAB One sided one-man type, steel construction with sliding door
access and tinted safety glass windows opening at side. Door
window is powered control.
Operator’s 3 way adjustable seat with headrest and armrest.
Hot water cab heater and air conditioning. (Optional)
TADANO Automatic Main unit in crane cab gives audible and visual warning of
Moment Limiter approach to overload. Automatically cuts out crane motions
(Model:AML-C) (including slewing motion) before overload.It also has the limit
function of working range(load radius and/or boom angle and/or
tip height and/or slewing range) .
Following functions are displayed.
Moment as percentage
Number of parts of line of rope
Boom angle
Boom length
Load radius
Outriggers position
Actual hook load
Permissible load
Boom position indicator
Potential hook height
Slewing angle
Main hydraulic oil pressure
Jib length and jib offset angle (only when jib operation)
OUTRIGGERS Hydraulically operated H-type outriggers. Each outrigger controlled
simultaneously or independently from either side of carrier.
Equipped with sight level gauge. Floats mounted integrally with
the jacks retract to within vehicle width.
All cylinders fitted with pilot check valves.
Crane operation with different extended length of each outrigger.
Equipped with extension width detector for each outrigger.
Extended width
Maximum ----- 6,800 mm
Middle --------- 4,600 mm
Minimum ------ 2,390 mm
Float size (Diameter) ----- 400 mm

-3-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

FRONT JACK A fifth hydraulically operated outrigger jack. Mounted to the

front frame of carrier to permit 360o lifting capabilities.
Hydraulic cylinder fitted with pilot check valve.
Float size (Diameter) --- 400 mm
COUNTER WEIGHT Integral with swing frame.
Mass-------------------------4,370 kg
STANDARD EQUIPMENT Automatic moment limiter (AML)
External lamp (AML)
Pendant type over-winding cutout
Winch automatic fail-safe brake
Cable follower
Hook safety latch
Pilot check valves
Counterbalance valves
Hydraulic pressure relief valves
Slewing brake
Slewing lock
Boom angle indicator
Boom elevation foot pedal
Boom telescoping foot pedal
Outrigger extension width detector
Front jack set up detector
Front jack overload alarm
Automatic Speed Reduction and Soft Stop function on boom
elevation and/or slewing (slewing range restricted only).
Hydraulic oil cooler
3 working lights
Front windshield wiper and washer
Roof window wiper and washer
Power window (Door of the cab)
3 way adjustable cloth seat with headrest and armrest
Cab floor mat
Sun visor (Front and roof)
OPTIONAL EQUIPMENT Hot water cab heater and air conditioner (Upper cab)
Winch drum mirror
Electric fan in cab
Winch drum rotation indicator (Visual type)
Hook block – 60t capacity
(6 sheaves, swivel type with safety latch.
Mass : approx.570 kg)
Hook block – 35 t capacity
(3 sheaves, swivel type with safety latch.
Mass : approx.410 kg)
Hook block – 5.6 t capacity
(Swivel type with safety latch for single line use.
Mass : approx.150 kg)
Over-unwinding prevention
Additional oil cooler
Anemometer
------------------------------------------------------------------------------------------------------------------------------
NOTE : Each crane motion speed is based on unladen conditions.

-4-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

CARRIER SPECIFICATIONS
MANUFACTURER TADANO LTD.

MODEL TC-4255-2 ------ Left-hand steering , 8 x 4

ENGINE Model --------- Daimler OM457LA

Type ----------- 4 cycle, turbo charged and inter cooled.
Piston displacement ---11,967 cm3
Bore x Stroke ----------- 128 mm x 155 mm
Max. output ------------- 260 kW {353 PS} at 1,900 min-1{rpm}
Max. torque ---------------1,850 N-m{188 kgf-m} at 1,100 min-1{rpm}

CLUTCH Dry single plate, hydraulically operated clutch release mechanism

with air assisted booster.

TRANSMISSION 9 forward and 1 reverse speeds, synchromesh on 2nd –9th gear

and constant-mesh on 1st and reverse gear.

AXLES Front ---------- Reverse-elliot type, steering axle.

Rear ----------- Full floating type, driving axle with inter-wheel
differential lock.

STEERING Dual circuit hydraulic and mechanical steering of both front

axles with hydraulic power booster.
3rd axle reduction gear-mounted emergency steering pump
(Optional).

SUSPENSION Front --------- Hydraulic/pneumatic suspension, with hydraulic

lock system and leveling adjustment.
Rear ---------- Hydraulic/pneumatic suspension, with hydraulic
lock system and leveling adjustment.

BRAKE SYSTEM Service ------- Full air brakes on all wheels. Dual-circuit system.
Parking/ Emergency
-------- Spring loaded brake on rear 4-wheel controlled
by knob of spring brake valve.
Auxiliary------- Constant throttle system with exhaust flap brake.

ELECTRIC SYSTEM 24 V DC. 2 batteries of 12 V

Alternator ---- 28 V – 80 A

FUEL TANK CAPACITY 300 liters

CAB 2-man full width cab of steel structure, with safety glass.
Seats adjustable and air-suspended with headrest and 3point
safety belt.

TIRES Front -----------315/80R22.5, Single x 4

Rear ------------315/80R22.5, Dual x 4
Spare ---------- 315/80R22.5, Single x 1

TURN RADIUS Min. turning radius (at center of extreme outer tire)
--------------11.3 m

-5-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

STANDARD EQUIPMENT Spare tire and carrier with lock key

Rear fog lights
Inter-wheel differential gear lock
Fuel tank cap with lock key
Air dryer
Towing hooks (Front and rear, Eye type)
Engine over-run alarm
Air filter warning light (Instrument cluster)
Cooling water level warning light
Engine hour meter
PTO hour meter
Reversing signal
Low air pressure warning lamp and buzzer
AM / FM radio
Adjustment and heating rearview mirror
Sun visor
Tilting-telescoping steering wheel
3 way adjustable air suspension seat
Tachometer/ Speedometer (with odometer)
Air conditioner (hot water cab heater and cooler) with defroster
3 point type seat belt
Windshield wiper (with intermittent wiping) and washer
Cigarette lighter
Owner's tool set
Cruise control
Transmission oil drain cock

OPTIONAL EQUIPMENT Emergency steering pump

Air pressure test connections
Tire inflation
Tool box with lock key
Front fog lights
Coolant drain cock

-6-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

WORKING RANGE

-7-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

WORKING RANGE

-8-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

GT-600EX RATED LIFTING CAPACITIES (BOOM)

UNIT:x1000 kg
Outriggers ｆｕｌｌｙ extended 6.8 ｍ

A 11.0 m 15.0 m 19.0 m 27.0 m 35.0 m 39.0 m 43.0 m

B C C C C C C C C C C
3.0 70 60.0 76 40.8 79 32.0 79 22.0
3.5 67 47.5 74 40.8 78 32.0 78 22.0
4.0 64 42.4 72 40.8 76 32.0 76 22.0 81 22.0 81 17.0
4.5 61 38.1 70 37.8 75 32.0 75 22.0 80 22.0 80 17.0
5.0 58 34.5 68 34.2 73 32.0 73 22.0 79 22.0 79 17.0
5.5 55 31.4 66 31.1 72 30.9 71 21.4 78 21.3 78 17.0
6.0 51 28.7 63 28.4 70 27.4 70 20.6 77 20.7 77 17.0 80 14.0 81 12.0
6.5 47 26.4 61 26.1 68 24.0 68 19.8 76 20.0 76 16.3 80 14.0 80 12.0
7.0 43 24.4 59 23.5 67 21.1 66 19.1 75 19.5 75 15.4 79 14.0 79 11.9 80 10.0
7.5 39 22.7 57 20.9 65 18.8 65 18.5 74 18.8 73 14.6 78 13.5 78 11.5 80 10.0
8.0 34 20.0 54 18.7 63 16.9 63 17.9 72 17.1 72 13.9 77 13.0 77 11.1 79 10.0 80 8.5
9.0 20 15.7 49 15.0 60 13.9 60 16.8 70 14.3 70 12.6 76 12.1 76 10.3 78 10.0 79 8.5
10.0 43 12.0 56 11.6 56 14.7 68 12.2 68 11.6 74 11.7 74 9.7 76 9.7 78 8.5
11.0 36 9.8 52 9.5 52 12.4 65 10.5 65 10.7 72 10.2 72 9.0 75 9.2 77 8.5
12.0 28 8.2 47 7.9 48 10.6 63 9.2 63 9.9 70 9.0 71 8.4 73 8.7 76 8.1
14.0 37 5.5 38 7.9 58 6.9 58 8.3 67 7.1 67 7.3 70 7.5 73 6.9
16.0 24 3.8 25 6.2 52 5.2 52 6.5 63 5.6 63 6.4 67 6.1 70 5.5
18.0 46 3.9 46 5.2 59 4.4 59 5.4 63 5.0 66 4.4
20.0 39 3.0 40 4.2 55 3.5 55 4.4 60 4.0 63 3.6
22.0 31 2.2 32 3.5 50 2.7 51 3.6 56 3.2 60 2.9
24.0 20 1.6 22 2.9 46 2.1 46 3.0 52 2.6 57 2.3
26.0 41 1.6 41 2.5 48 2.1 53 1.8
28.0 35 1.2 35 2.1 43 1.7 50 1.4
30.0 28 0.8 28 1.7 39 1.3 46 1.0
32.0 18 0.5 18 1.4 33 1.0 42 0.7
34.0 26 0.8 37 0.5
36.0 17 0.6
D 0 18 0 17 37
Telescoping conditions (%)

Telescoping
mode
I ,II I I II I II I II II I ,II

2nd boom 0 50 100 0 100 0 100 0 50 100

3rd boom 0 0 0 33 33 66 66 100 100 100
4th boom 0 0 0 33 33 66 66 100 100 100
Top boom 0 0 0 33 33 66 66 100 100 100

A: Boom length (m)

B: Load radius (m)
C: Loaded boom angle (o)
D: Minimum boom angle (o) for indicated length (no load)

-9-
 SPEC. SHEET No. GT-600E-1-00301/EX-21

GT-600EX RATED LIFTING CAPACITIES (BOOM)

UNIT:x1000 kg
Outriggers extended to middle 4.6 ｍ
A 11.0 m 15.0 m 19.0 m 27.0 m 35.0 m 39.0 m 43.0 m
B C C C C C C C C C C
3.0 70 40.0 76 36.0 80 32.0 79 22.0
3.5 67 34.0 74 29.2 78 24.5 78 22.0
4.0 64 27.8 72 22.9 76 19.6 76 22.0 81 17.0 81 17.0
4.5 61 22.3 70 18.6 75 16.0 74 19.1 80 14.4 80 16.4
5.0 58 18.4 68 15.4 73 13.4 73 16.3 79 12.4 79 14.3
5.5 55 15.4 65 13.0 71 11.3 71 14.1 77 10.7 78 12.5
6.0 51 13.2 63 11.2 70 9.7 70 12.3 76 9.4 76 11.1 80 8.7 80 10.0
6.5 47 11.4 61 9.6 68 8.3 68 10.9 75 8.2 75 9.9 79 7.8 80 9.0
7.0 43 9.9 59 8.3 66 7.2 66 9.7 74 7.3 74 9.0 78 6.9 79 8.2 80 7.4
7.5 39 8.5 57 7.3 64 6.3 64 8.7 73 6.4 73 8.1 77 6.2 78 7.5 79 6.7
8.0 33 7.3 54 6.3 63 5.5 63 7.8 72 5.7 72 7.4 77 5.6 77 6.8 78 6.1 80 5.3
9.0 19 5.5 49 4.9 59 4.1 59 6.4 69 4.6 70 6.1 75 4.6 75 5.7 77 5.1 78 4.4
10.0 43 3.7 55 3.1 55 5.3 67 3.6 67 5.2 73 3.7 73 4.9 75 4.3 77 3.6
11.0 36 2.7 51 2.2 51 4.4 65 2.9 65 4.4 71 3.0 71 4.2 74 3.6 76 3.0
12.0 28 1.9 47 1.5 47 3.5 62 2.3 62 3.7 69 2.5 70 3.6 72 3.1 74 2.5
14.0 38 2.3 57 1.3 57 2.7 66 1.6 66 2.7 69 2.2 71 1.6
16.0 25 1.5 52 1.9 62 2.0 66 1.5
18.0 46 1.2 58 1.4
20.0 39 0.7 54 0.9
D 0 0 37 0 56 37 65 53 63 70
Telescoping conditions (%)
Telescoping
mode
I ,II I I II I II I II II I ,II
2nd boom 0 50 100 0 100 0 100 0 50 100
3rd boom 0 0 0 33 33 66 66 100 100 100
4th boom 0 0 0 33 33 66 66 100 100 100
Top boom 0 0 0 33 33 66 66 100 100 100

UNIT:x1000 kg
Outriggers extended to minimum 2.39 m
A 11.0 m 15.0 m 19.0 m
B C C C C
3.0 70 17.9 76 15.0 79 12.9 79 15.5
3.5 67 14.5 74 12.3 78 10.6 77 13.0
4.0 64 12.0 72 10.1 76 8.8 76 11.1
4.5 61 10.0 70 8.5 74 7.4 74 9.6
5.0 58 8.5 67 7.1 73 6.2 73 8.3
5.5 55 7.3 65 6.0 71 5.2 71 7.3
6.0 51 6.2 63 5.1 70 4.3 69 6.4
6.5 47 5.4 61 4.3 68 3.6 68 5.7
7.0 43 4.6 59 3.7 66 3.0 66 5.0
7.5 39 3.9 56 3.1 64 2.5 64 4.5
8.0 33 3.3 54 2.6 63 2.0 63 4.0
9.0 19 2.3 48 1.7 59 1.2 59 3.2
10.0 43 1.1 55 2.5
11.0 39 0.5 51 2.0
12.0 47 1.5
14.0 38 0.7
D 0 0 58 36
Telescoping conditions (%)
Telescoping
mode
I ,II I I II
2nd boom 0 50 100 0 A: Boom length (m)
3rd boom 0 0 0 33 B: Load radius (m)
4th boom 0 0 0 33 C: Loaded boom angle (o)
Top boom 0 0 0 33 D: Minimum boom angle (o) for indicated length (no load)

- 10 -
 SPEC. SHEET No. GT-600E-1-00301/EX-21

GT-600EX RATED LIFTING CAPACITIES (JIB)

Outriggers ｆｕｌｌｙ extended 6.8 ｍ

43.0 m Boom + 8.8 m Jib 43.0 m Boom + 15.2 m Jib
Boom Boom
angle 5o Tilt 25o Tilt 45o Tilt angle 5o Tilt 25o Tilt 45o Tilt
R W R W R W R W R W R W
o o
81 9.2 4.00 12.2 3.58 14.1 2.47 81 11.3 2.60 16.2 1.69 19.5 1.17
80o 10.2 4.00 13.3 3.50 15.1 2.44 80o 12.5 2.60 17.4 1.65 20.6 1.15
o o
79 11.3 4.00 14.2 3.42 15.9 2.40 79 13.6 2.60 18.4 1.61 21.5 1.13
78o 12.3 4.00 15.1 3.32 16.8 2.37 78o 14.8 2.60 19.5 1.58 22.4 1.12
77o 13.3 4.00 16.0 3.22 17.6 2.34 77o 15.9 2.56 20.4 1.54 23.4 1.10
76o 14.2 3.85 16.9 3.12 18.5 2.32 76o 17.0 2.46 21.5 1.51 24.3 1.09
75o 15.2 3.72 17.7 3.04 19.3 2.29 75o 18.1 2.38 22.4 1.48 25.2 1.08
73o 17.0 3.50 19.5 2.88 21.0 2.24 73o 20.1 2.22 24.3 1.43 27.0 1.05
70o 19.5 3.20 22.0 2.68 23.3 2.18 70o 23.0 2.01 27.2 1.35 29.4 1.02
68o 21.4 3.03 23.6 2.56 24.8 2.14 68o 25.1 1.90 29.0 1.31 31.1 1.00
o o
65 23.7 2.52 25.9 2.25 27.0 2.09 65 27.8 1.75 31.8 1.25 33.5 0.98
63o 25.1 2.13 27.2 1.92 28.4 1.86 63o 29.5 1.52 33.3 1.21 35.1 0.97
60o 27.3 1.66 29.3 1.52 30.4 1.48 60o 31.8 1.14 35.7 0.99 37.1 0.95
58o 28.8 1.40 30.7 1.28 31.7 1.24 58o 33.4 0.92 37.0 0.81 38.2 0.77
55o 30.9 1.07 32.7 0.96 33.4 0.93 55o 35.7 0.66 39.1 0.56 40.1 0.53
53o 32.2 0.86 33.9 0.77 34.6 0.75
50o 34.1 0.58 35.7 0.52 36.4 0.51
48o 35.3 0.43

Outriggers ｆｕｌｌｙ extended 6.8 ｍ

39.0 m Boom (telescoping mode II) + 8.8 m Jib 39.0 m Boom (telescoping mode II) + 15.2 m Jib
Boom Boom
angle 5o Tilt 25o Tilt 45o Tilt angle 5o Tilt 25o Tilt 45o Tilt
R W R W R W R W R W R W
81o 8.1 4.40 11.0 3.58 13.0 2.47 81o 10.2 2.60 15.0 1.69 18.3 1.17
80o 9.0 4.40 11.9 3.50 13.8 2.44 80o 11.3 2.60 16.0 1.65 19.3 1.15
o o
79 9.9 4.40 12.8 3.42 14.7 2.40 79 12.3 2.60 16.9 1.61 20.2 1.13
78o 10.9 4.40 13.7 3.35 15.5 2.37 78o 13.4 2.60 17.9 1.58 21.0 1.12
77o 11.8 4.40 14.5 3.28 16.3 2.34 77o 14.4 2.56 18.8 1.54 21.9 1.10
76o 12.6 4.24 15.3 3.21 17.1 2.32 76o 15.4 2.46 19.8 1.51 22.7 1.09
75o 13.5 4.09 16.1 3.15 17.8 2.29 75o 16.3 2.38 20.7 1.48 23.5 1.08
73o 15.1 3.85 17.8 3.04 19.3 2.24 73o 18.2 2.22 22.5 1.43 25.1 1.05
70o 17.6 3.51 20.1 2.89 21.5 2.18 70o 20.9 2.01 25.1 1.35 27.4 1.02
68o 19.2 3.32 21.7 2.78 22.8 2.14 68o 22.7 1.90 26.8 1.31 28.9 1.00
65o 21.5 3.07 23.8 2.61 24.8 2.09 65o 25.3 1.75 29.1 1.25 31.0 0.98
63o 23.0 2.93 25.2 2.52 26.2 2.07 63o 27.0 1.67 30.8 1.21 32.4 0.97
60o 25.1 2.58 27.2 2.31 28.2 2.03 60o 29.4 1.56 33.0 1.16 34.4 0.95
58o 26.5 2.26 28.5 2.02 29.5 1.93 58o 31.1 1.49 34.5 1.13 35.7 0.94
55o 28.3 1.83 30.3 1.65 31.1 1.59 55o 33.2 1.29 36.5 1.09 37.5 0.93
53o 29.6 1.59 31.4 1.44 32.1 1.40 53o 34.6 1.10 37.8 0.96 38.6 0.90
50o 31.4 1.28 33.1 1.17 33.7 1.14 50o 36.6 0.85 39.4 0.74 40.0 0.71
48o 32.5 1.10 34.1 1.01 34.6 0.99 48o 37.8 0.70 40.5 0.62 41.0 0.59
45o 34.2 0.87 35.6 0.80 35.9 0.79 45o 39.6 0.51 42.1 0.45 42.3 0.44
43o 35.3 0.74 36.6 0.68 43o 40.8 0.41
40o 36.8 0.57 37.4 0.52
38o 37.7 0.46 38.8 0.43 R: Load radius (m)
W: Rated lifting capacity (Unit: x 1,000 kg)

- 11 -
 SPEC. SHEET No. GT-600E-1-00301/EX-21

GT-600EX RATED LIFTING CAPACITIES (JIB)

Outriggers ｆｕｌｌｙ extended 6.8 ｍ

35.0 m Boom (telescoping mode I) + 8.8 m Jib 35.0 m Boom (telescoping mode I) + 15.2 m Jib
Boom Boom
angle 5o Tilt 25o Tilt 45o Tilt angle 5o Tilt 25o Tilt 45o Tilt
R W R W R W R W R W R W
o o
81 7.3 4.50 10.3 3.58 12.1 2.47 81 9.2 2.60 14.1 1.69 17.6 1.17
o o
80 8.1 4.50 11.1 3.50 12.8 2.44 80 10.1 2.60 15.0 1.65 18.4 1.15
79o 8.9 4.50 11.8 3.42 13.5 2.40 79o 10.9 2.60 15.9 1.61 19.2 1.13
o o
78 9.7 4.50 12.5 3.35 14.2 2.37 78 12.0 2.60 16.8 1.58 20.0 1.12
o o
77 10.5 4.50 13.4 3.28 14.9 2.34 77 12.9 2.56 17.6 1.54 20.7 1.10
o o
76 11.3 4.50 14.1 3.21 15.6 2.32 76 13.8 2.46 18.5 1.51 21.5 1.09
75o 12.1 4.50 14.9 3.15 16.3 2.29 75o 14.7 2.38 19.3 1.48 22.2 1.08
73o 13.6 4.50 16.3 3.04 17.7 2.24 73o 16.5 2.22 20.9 1.43 23.7 1.05
o o
70 16.0 4.44 18.5 2.89 19.6 2.18 70 18.9 2.01 23.3 1.35 25.7 1.02
o o
68 17.4 4.21 19.8 2.80 20.9 2.14 68 20.6 1.90 24.8 1.31 27.1 1.00
o o
65 19.5 3.91 21.8 2.69 22.7 2.09 65 22.9 1.75 27.0 1.25 29.0 0.98
63o 20.8 3.53 23.1 2.62 23.9 2.07 63o 24.5 1.67 28.5 1.21 30.3 0.97
o o
60 22.6 2.90 25.1 2.53 25.7 2.03 60 26.8 1.56 30.5 1.16 32.0 0.95
o o
58 23.9 2.52 26.2 2.27 26.9 2.01 58 28.3 1.49 31.8 1.13 33.3 0.94
o o
55 25.6 2.03 27.8 1.85 28.4 1.76 55 30.4 1.41 33.8 1.09 34.8 0.93
53o 26.8 1.75 28.9 1.61 29.4 1.54 53o 31.7 1.25 34.9 1.06 35.9 0.92
o o
50 28.4 1.40 30.3 1.29 30.8 1.25 50 33.5 0.96 36.5 0.82 37.2 0.77
o o
48 29.5 1.20 31.4 1.11 31.7 1.08 48 34.7 0.80 37.5 0.68 38.1 0.64
o o
45 31.0 0.94 32.7 0.88 32.9 0.86 45 36.4 0.58 38.9 0.50 39.3 0.47
o o
43 32.0 0.79 33.6 0.74 43 37.5 0.46
40o 33.4 0.59 34.8 0.56 R: Load radius (m)
o
38 34.3 0.48 35.6 0.45 W: Rated lifting capacity (Unit: x 1,000 kg)

- 12 -
 SPEC. SHEET No. GT-600E-1-00301/EX-21

GT-600EX RATED LIFTING CAPACITIES (JIB)

Outriggers extended to middle 4.6 ｍ

43.0 m Boom + 8.8 m Jib 43.0 m Boom + 15.2 m Jib
Boom o o o Boom o
angle 5 Tilt 25 Tilt 45 Tilt angle 5 Tilt 25o Tilt 45o Tilt
R W R W R W R W R W R W
o o
81 9.2 4.00 12.6 3.16 14.1 2.47 81 11.3 2.60 16.2 1.69 19.5 1.17
o o
80 10.1 3.49 12.9 2.74 15.1 2.43 80 12.4 2.48 17.3 1.65 20.9 1.15
o o
79 10.9 2.99 13.6 2.38 15.8 2.13 79 13.4 2.08 18.2 1.45 21.5 1.13
o o
78 11.7 2.56 14.5 2.06 16.5 1.85 78 14.2 1.72 19.1 1.22 22.4 1.07
o o
77 12.6 2.18 15.2 1.77 17.2 1.60 77 15.1 1.42 19.9 1.02 23.1 0.90
o o
76 13.4 1.85 16.0 1.50 18.0 1.38 76 16.0 1.15
o
75 14.2 1.55 16.8 1.26 18.7 1.17

Outriggers extended to middle 4.6 ｍ

39.0 m Boom (telescoping mode II) + 8.8 m Jib 39.0 m Boom (telescoping mode II) + 15.2 m Jib
Boom o o o Boom
angle 5 Tilt 25 Tilt 45 Tilt angle 5o Tilt 25o Tilt 45o Tilt
R W R W R W R W R W R W
o o
81 8.1 4.40 11.0 3.58 13.0 2.47 81 10.2 2.60 15.0 1.69 18.4 1.17
o
80 9.0 4.40 11.9 3.50 13.8 2.44 80o 11.3 2.60 16.0 1.65 19.3 1.15
o o
79 9.9 4.21 12.7 3.30 14.6 2.40 79 12.3 2.60 17.0 1.61 20.1 1.13
o o
78 10.7 3.70 13.5 2.94 15.5 2.37 78 13.4 2.60 17.9 1.58 21.0 1.12
o o
77 11.4 3.25 14.3 2.62 16.3 2.34 77 14.2 2.31 18.8 1.54 21.9 1.10
o o
76 12.2 2.86 15.0 2.33 16.9 2.10 76 15.0 1.99 19.8 1.50 22.7 1.09
o o
75 13.0 2.52 15.7 2.06 17.7 1.88 75 15.8 1.72 20.6 1.31 23.5 1.08
o o
73 14.5 1.94 17.2 1.61 19.0 1.48 73 17.5 1.26 22.1 0.98 25.0 0.87
o
70 16.8 1.26 19.3 1.06 21.0 0.99
68o 18.3 0.91 20.7 0.76 22.2 0.72

Outriggers extended to middle 4.6 ｍ

35.0 m Boom (telescoping mode I) + 8.8 m Jib 35.0 m Boom (telescoping mode I) + 15.2 m Jib
Boom o o o Boom
angle 5 Tilt 25 Tilt 45 Tilt angle 5o Tilt 25o Tilt 45o Tilt
R W R W R W R W R W R W
o o
81 7.3 4.50 10.3 3.58 12.1 2.47 81 9.1 2.60 14.0 1.69 17.6 1.17
o o
80 8.1 4.50 11.1 3.50 12.8 2.44 80 10.1 2.60 15.0 1.65 18.4 1.15
o o
79 8.9 4.50 11.8 3.42 13.5 2.40 79 11.0 2.60 15.8 1.61 19.1 1.13
o o
78 9.7 4.24 12.6 3.35 14.2 2.37 78 12.0 2.60 16.7 1.58 19.9 1.12
o o
77 10.3 3.72 13.3 3.01 14.9 2.34 77 12.9 2.56 17.5 1.54 20.6 1.10
o o
76 11.0 3.26 14.0 2.67 15.6 2.32 76 13.8 2.40 18.4 1.51 21.5 1.09
o o
75 11.7 2.85 14.7 2.37 16.3 2.10 75 14.5 2.08 19.2 1.48 22.2 1.08
o o
73 13.1 2.18 16.0 1.84 17.5 1.65 73 16.1 1.55 20.7 1.14 23.5 0.96
o o
70 15.2 1.40 18.0 1.21 19.3 1.10 70 18.4 0.93
o
68 16.5 1.00 19.1 0.86 20.5 0.79

R: Load radius (m)

W: Rated lifting capacity (Unit: x 1,000 kg)

- 13 -
 SPEC. SHEET No. GT-600E-1-00301/EX-21

NOTES

1. Rated lifting capacities shown in the table are based on condition that the crane is set on firm
level surface. Those above bold lines are based on crane strength and those below, on
its stability.
2. Rated lifting capacities based on crane stability are according to ISO 4305 / DIN 15019 part 2.
3. The mass of the hook (570 kg for *60 t capacity, 410 kg for *35 t capacity, 150 kg for *5.6 t capacity),
slings and all similarly used load handling devices must be considered as part of the load and must
be deducted from the lifting capacities.
* : Optional
4. For rated lifting capacity of single top, reduce the rated lifting capacities of relevant boom according
to a weight reduction for auxiliary load handling equipment. Capacities of single top shall not
exceed 5,600 kg including main hook.
5. Standard number of part lines for each boom length is as shown below. Load per line should
not surpass 54.9 kN {5,600 kgf} for main winch and auxiliary winch.
11.0 m to 15.0 m to 19.0 m to 27.0 m to
Boom length 11.0 m Jib / Single top
15.0 m 19.0 m 27.0 m 43.0 m
No. of part lines 12 10 7 5 4 1
The lifting capacity data stored in the AUTOMATIC MOMENT LIMITER (AML) is based on the
standard number of parts of line listed in the chart.
Maximum lifting capacity is restricted by the number of parts of line of AUTOMATIC MOMENT
LIMITER (AML).
6. Without front jack extended, when the boom is within the Over-front, rated lifting capacities
are different from those for the boom in the Over-side and Over-rear.

- 14 -
 SPEC. SHEET No. GT-600E-1-00301/EX-21

D IM E N S IO N S

- 15 -