Scribd Logo
Upload

Welcome to Scribd!

  • 129 views

    23 - Well Control Worksheet-Surface BOP

    Uploaded by

    Junaid Mateen
    This document appears to be a well control worksheet containing information about a well kick such as well geometry, mud weights, pump specifications, and calculations for killing the well. It provides default values for a duplex mud pump and rules of thumb for determining kill rates and mixing times. The document also outlines a general well kill procedure in 5 steps that involves increasing mud weight, maintaining constant pump rate and drill pipe pressure, and bleeding off any residual pressure once the kill mud reaches surface.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd

    23 - Well Control Worksheet-Surface BOP

    Uploaded by

    Junaid Mateen
    129 views2 pages
    This document appears to be a well control worksheet containing information about a well kick such as well geometry, mud weights, pump specifications, and calculations for killing the well. It provides default values for a duplex mud pump and rules of thumb for determining kill rates and mixing times. The document also outlines a general well kill procedure in 5 steps that involves increasing mud weight, maintaining constant pump rate and drill pipe pressure, and bleeding off any residual pressure once the kill mud reaches surface.

    Original Title

    23_Well Control Worksheet-Surface BOP

    Copyright

    © © All Rights Reserved

    Available Formats

    XLS, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document appears to be a well control worksheet containing information about a well kick such as well geometry, mud weights, pump specifications, and calculations for killing the well. It provides default values for a duplex mud pump and rules of thumb for determining kill rates and mixing times. The document also outlines a general well kill procedure in 5 steps that involves increasing mud weight, maintaining constant pump rate and drill pipe pressure, and bleeding off any residual pressure once the kill mud reaches surface.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    129 views2 pages

    23 - Well Control Worksheet-Surface BOP

    Uploaded by

    Junaid Mateen
    This document appears to be a well control worksheet containing information about a well kick such as well geometry, mud weights, pump specifications, and calculations for killing the well. It provides default values for a duplex mud pump and rules of thumb for determining kill rates and mixing times. The document also outlines a general well kill procedure in 5 steps that involves increasing mud weight, maintaining constant pump rate and drill pipe pressure, and bleeding off any residual pressure once the kill mud reaches surface.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    of 2

    Name of Company:

    Well Name & Number: WELL CONTROL WORK


    WAIT & WEIGHT Method - Surface BOP
    Microsoft Excel 97 Date: February 9, 2022 SHEET
    Stack
    WELL GEOMETRY SEC 1 SEC 2 SEC 3 SEC 4 SEC 5 SEC 6 SEC 7
    Length, ft? =
    Hole Size, in? =
    Pipe OD, in? =
    Pipe ID, in? =
    PRE-KICK INFORMATION MUD PUMP CALCULATE A TVD
    Present or Old Mud Weight, ppg? = Liner Size, in? = Angle Last Survey? =
    TVD of Integrity Test @ Last Shoe, ft? = Stroke Length, in? = MD Last Survey? =
    Integrity Test @ Last Shoe, ppg? = Rod Size, in? = 0 TVD Last Survey? =
    Slow Rate Pump Pressure? = Efficiency (1-100)? = MD for New TVD? =
    Slow Pump Rate, spm? = Triplex, bbl/stk 0.0000 TVD Result, ft
    NOTES …
    Volume in Active Mud Pits, bbls? = 1. Enter Well Geometry from the bottom of the hole starting in SEC 1.
    KICK INFORMATION 2. The mud pump defaults to a Duplex when the rod size greater than
    zero.
    TVD of Well, ft? = 3. The result in cell J27 is the TVD to spot a mud weight equal to the last
    Stabilized Shut-in Drill Pipe Pressure? = Integrity Test @ Shoe to generate a BHP equal to a hole full of KWM.
    4. A red triangle in upper right hand corner of cell is a comment for the
    Stabilized Shut-in Casing Pressure? = user.
    Pit Gain, bbls? = Move cursor over cell for viewing.
    KILL RESULTS

    New Mud Weight Required for Kill, ppg 0.00 Mud Weight For a 100 psi Trip Margin, ppg 0.00
    Initial Circulating Drill Pipe Pressure 0 Estimated Length of Kick Material, ft #DIV/0!
    Final Circulating Drill Pipe Pressure 0 Estimated Density of Kick Material, ppg #DIV/0!
    Surface to Bit, stks 0 Maximum Allowable Casing Pressure, psi 0
    Surface to Surface, stks 0 Minimum Depth to Run Drill Pipe For a Kill Off-Bottom 0
    Drill Pipe Pressure Schedule SUMMARY OFDRILL
    RESULTS
    PIPEFOR
    SUMMARY
    DRILL PIPE SECTION
    Strokes Pressure Minutes Capacity, bbls 0
    0 0 #DIV/0! Displacement, bbls 0
    0 0 #DIV/0! Surface to Bit, strokes 0
    0 0 #DIV/0! Measured Depth or Length of Drill String, ft 0
    0 0 #DIV/0! SUMMARY OF RESULTS FOR ANNULUS SECTION

    0 0 #DIV/0! Capacity, bbls 0


    0 0 #DIV/0! Bit to Surface, strokes 0
    0 0 #DIV/0! Bit to Surface, minutes 0
    0 0 #DIV/0! BARITE REQUIREMENTS
    0 0 #DIV/0! Barite Required to Weight-Up 100 Barrels of Mud, sacks 0
    0 0 #DIV/0! Barite Required To Weight-Up System, sacks 0
    0 0 #DIV/0! Mud Volume Increase Due To Weighting-Up, bbls 0
    Density of Kick < 6 ppg = Gas Present Minimum Mixing Rate, sacks/min 0.00
    DRILL PIPE RESULTS BY SECTION SEC 1 SEC 2 SEC 3 SEC 4 SEC 5 SEC 6 SEC 7
    Barrels 0.0 0.0 0.0 0.0 0.0 0.0 0.0
    Strokes 0 0 0 0 0 0 0
    Displacement, bbl 0.0 0.0 0.0 0.0 0.0 0.0 0.0
    ANNULUS RESULTS BY SECTION SEC 1 SEC 2 SEC 3 SEC 4 SEC 5 SEC 6 SEC 7
    Barrels 0.0 0.0 0.0 0.0 0.0 0.0 0.0
    Strokes 0 0 0 0 0 0 0
    Annular Velocity, fpm 0 0 0 0 0 0 0
    A. The Rule of Thumb to determine a kill rate is to consider an average annular velocity of 40 to 50 fpm around the drill collars.
    B. The Minimum Mixing Rate result is based on the Slow Pump Rate.
    A GENERAL WELL KILL PROCEDURE…
    1. Increase mud weight in active pits to KILL WEIGHT.
    2. Zero stroke counters. Start pump and simultaneously open choke. Pressure on the choke initially should be the
    shut-in casing pressure and this pressure should be maintained while the pump rate is brought up to the kill rate.
    3. HOLD PUMP RATE CONSTANT and adjust choke so that the drill pipe pressure follows the calculated schedule.
    If drill pipe pressure is too high, open the choke slightly; if it is too low, close choke slightly. Takes approximately
    one second per thousand feet of hole to see a response at gauge when the choke setting is altered.
    4. After the Kill Mud has filled the drill pipe, MAINTAIN CONSTANT PUMP RATE and CONSTANT DRILL PIPE
    PRESSURE until the annulus is filled with the kill mud.
    5. When kill weight mud reaches surface, stop the pump and shut well in. At this time, the casing pressure and drill pipe
    pressure should be zero. If some pressure still exist on casing, open choke slightly and bleed a small amount or
    volume of mud. If the well is dead, pressure should fall to zero and there should be no flow from well.
    Reference: LSU Blowout Control School Manual, LSU - Baton Rouge, La.
    THE END

    You might also like