HDL® BACNet Manual

1. Introduction

HDL-Bacnet module is a Bacnet HDL Data convertor, it can realize the control from
Bacnet system to HDL-BUS system.

Bacnet HDL-BUS
Data convertor

RJ45 BACNet system

（ the manual is based on
BACNet client app ）

HDL-BUS

………
.
2.HDL-BUS
HDL-Bacnet module configuration instruction

Relay Dimmer Sensor DLP Panel

HDL-BUS system devices should be setup inside HDL-BUS configuration software when
controlled by Bacnet client. Open HDL-BUS configuration software, search and set
parameters of the HDL-Bacnet module.

2.1 Basic information setting

0
 HDL® BACNet Manual

HDL-Bacnet convertor embedded HDL-BUS IP

gateway function, need to set Ethernet
parameters firstly

Attention: the IP address of Ethernet parameters should be in the same Ethernet

segment with Bacnet client.
2.2 Parameters setting
Select to enable IP switch function

Default value, fixed

Control target ，
Maximum 150

(1) (2) (3) (4) (5)

(1) Bacnet ID includes different types: AI, AO, AV, BI, BO, BV, MI, MO, MV, other, not much
differences between different types, but for the convenience of management by client.
The value of ID is control point, it is user-defined, cannot be duplicate.
(2) The Hex value is auto generated according Bacnet ID type and ID value
(3) type of control target, It indicates the type of HDL-BUS controlled targets
(4) ID of HDL-BUS controlled devices.
(5) the parameter of controlled target, all supported parameters up to now, refer to below
table

1
 HDL® BACNet Manual

3. Example setting

Take example of control the third ch of relay module

parameters setting in HDL-BUS configuration software：

Control ID of relay Controlled Remarks

target type module channel

Corresponding Setting in Bacnet client:

Double click to type the vale

Control target

Type 100, switch on the channel

Type 0, switch off the channel.

Addendum: supported parameter type and parameter settings

Configuration tab BACnet control parameters

2
 HDL® BACNet Manual

HDL control BACNET WP Present Value

Parameter 1 Parameter 2
type definition and validation scope
0invalid switch xxx xxx invalid

Area Scene No.: 0－12

Scene control Device Area No. N/A “0” means switch off Scene，1－
12 is Scene No.
Sequence
Device Area No. N/A Area Sequence No.: 1－6
control
universal switch Switch No. N/A Switch status: 1: on, 0: off
single channel Device channel adjustment Intensity value of ch: 0－100
lighting No. time 0: off, 100: on
time switch Channel No. N/A Switch status: 1: on, 0: off
Curtain switch status: 0: stop,
curtain switch Curtain No. N/A
1: open, 2: close
Command Status: 0: invalid,
GPRS control Command No. N/A
1: SMS, 2: remote

Panel control IR Receiving

N/A 1: enable 0: disable
enabling
Panel locking N/A 1: lock 0: unlock
AC switch N/A 1: on 0: off
temperature value setting scope:　
cooling
N/A 0－30 degree Celsius
temperature of AC
degrees Fahrenheit 32－86
0: Auto, 1: high,
Fan speed of AC N/A
2: Medium 3: low
0: cooling, 1: heating
AC mode N/A 2: Ventilaiton, 3: Auto,
4: dehumidification.
temperature value setting scope:
Heating
N/A 0－30 degree Celsius
temperature of AC
degrees Fahrenheit 32－86
temperature value setting scope:
Auto temperature
N/A 0－30 degree Celsius
of AC
degrees Fahrenheit 32－86
increase Temperature increasing Value :(1-
N/A
temperature 5℃/℉)
decrease Temperature decreasing Value :
N/A
temperature (1-5℃/℉)
Backlight switch N/A 1: on 0: off
AC locking N/A 1:lock 0:unlock
Backlight intensity N/A Backlight intensity value (0-100%)

3
 HDL® BACNet Manual

status indicator Status indicator intensity value (0-

N/A
intensity 100%)
button shielding of
Button No. 0: shielded，1: unshielded
panel
page shielding of
Page No. 0: shielded，1: unshielded
panel
temperature value setting scope:
dehumidification
N/A 0－30 degree Celsius
temperature of AC
degrees Fahrenheit 32－86
heating switch N/A 0: off，1: on
Mode: (5: time,4: leaving mode,
Heating mode N/A
3: night, 2: daytime,1: normal)
increase heating Temperature increasing Value :(1-
N/A
temperature 5℃/℉)
decrease heating Temperature decreasing Value :
N/A
temperature (1-5℃/℉)
setting page
panel control N/A 1: lock 0: unlock
locking

broadcast scene All areas（255） N/A Scene No.: 0－12

broadcast All
N/A Intensity of light ch: 0－100
channel Channel（255）
Security modes(1-6)：01:
Security Area Vacation, 02: leaving, 03: night,
Security module N/A
（1－8） 04: night party, 05: daytime,
06: disalarm