SAFETY DATA SHEET

SteelMaster 60SB
Section 1. Identification
GHS product identifier : SteelMaster 60SB
Other means of identification : Not available.
Product code : 14880
Product description : Paint.
Product type : Liquid.

Relevant identified uses of the substance or mixture and uses advised against

Identified uses
Use in coatings - Industrial use
Use in coatings - Professional use

Manufacturing country : Jotun Thailand Limited

700/353 Amata Nakorn Industrial Estate (BIP 2)
Moo 6, Tumbol Donhualoh, Amphur Muang Chonburi
Chonburi 20000 Thailand

Phone: + 66 2 022 9888

Fax: + 66 2 022 9888 , + 66 38 214 375

[email protected]

Emergency telephone number : Jotun Thailand Limited

Phone: + 66 2 022 9888 ext. 2100, 2400, 2402

14880 1 14880
^(ValidationDate) 1
Approved

Section 2. Hazards identification

Classification of the : FLAMMABLE LIQUIDS - Category 3
substance or mixture SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/EYE IRRITATION - Category 2A
REPRODUCTIVE TOXICITY (Fertility) - Category 2

GHS label elements

Hazard pictograms :

Signal word : Warning.

Hazard statements : H226 - Flammable liquid and vapour.
H319 - Causes serious eye irritation.
H315 - Causes skin irritation.
H361 - Suspected of damaging fertility.
Precautionary statements

Date of issue : 01.12.2020 1/11

SteelMaster 60SB

Section 2. Hazards identification

Prevention : P201 - Obtain special instructions before use.
P202 - Do not handle until all safety precautions have been read and understood.
P281 - Use personal protective equipment as required.
P280 - Wear protective gloves. Wear eye or face protection.
P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P233 - Keep container tightly closed.
P264 - Wash hands thoroughly after handling.
Response : P308 + P313 - IF exposed or concerned: Get medical attention.
P302 + P352 + P362 + P363 - IF ON SKIN: Wash with plenty of soap and water.
Take off contaminated clothing. Wash contaminated clothing before reuse.
P332 + P313 - If skin irritation occurs: Get medical attention.
P305 + P351 + P338 - IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 - If eye irritation persists: Get medical attention.
Storage : P405 - Store locked up.
P403 - Store in a well-ventilated place.
P235 - Keep cool.
Disposal : P501 - Dispose of contents and container in accordance with all local, regional,
national and international regulations.

Other hazards which do not : None known.

result in classification

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of identification : Not available.

CAS number/other identifiers

CAS number : Not applicable.
EC number : Mixture.
Product code : 14880
Ingredient name % CAS number
xylene ≥10 - <20 1330-20-7
melamine ≤10 108-78-1
ethylbenzene <10 100-41-4
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this
section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
If not breathing, if breathing is irregular or if respiratory arrest occurs, provide
artificial respiration or oxygen by trained personnel. It may be dangerous to the
person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If
unconscious, place in recovery position and get medical attention immediately.
Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or
waistband. In case of inhalation of decomposition products in a fire, symptoms may
be delayed. The exposed person may need to be kept under medical surveillance
for 48 hours.

Date of issue : 01.12.2020 2/11

SteelMaster 60SB

Section 4. First aid measures

Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash
clothing before reuse. Clean shoes thoroughly before reuse.
Ingestion : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air
and keep at rest in a position comfortable for breathing. If material has been
swallowed and the exposed person is conscious, give small quantities of water to
drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs,
the head should be kept low so that vomit does not enter the lungs. Get medical
attention. Never give anything by mouth to an unconscious person. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : Causes serious eye irritation.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain or irritation
watering
redness
Inhalation : Adverse symptoms may include the following:
reduced foetal weight
increase in foetal deaths
skeletal malformations
Skin contact : Adverse symptoms may include the following:
irritation
redness
reduced foetal weight
increase in foetal deaths
skeletal malformations
Ingestion : Adverse symptoms may include the following:
reduced foetal weight
increase in foetal deaths
skeletal malformations

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.

See toxicological information (Section 11)

Section 5. Firefighting measures

Extinguishing media
Suitable extinguishing media : Use dry chemical, CO₂, water spray (fog) or foam.
Unsuitable extinguishing : Do not use water jet.
media

Specific hazards arising from : Flammable liquid and vapour. Runoff to sewer may create fire or explosion hazard.
the chemical In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion.

Date of issue : 01.12.2020 3/11

SteelMaster 60SB

Section 5. Firefighting measures

Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
nitrogen oxides
carbonyl halides
metal oxide/oxides

Special protective actions for : Promptly isolate the scene by removing all persons from the vicinity of the incident if
fire-fighters there is a fire. No action shall be taken involving any personal risk or without
suitable training. Move containers from fire area if this can be done without risk.
Use water spray to keep fire-exposed containers cool.
Special protective equipment : Fire-fighters should wear appropriate protective equipment and self-contained
for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilt material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapour or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

Environmental precautions : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).

Methods and material for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble.
Alternatively, or if water-insoluble, absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a licensed waste disposal
contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach the release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an
effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
and place in container for disposal according to local regulations (see Section 13).
Dispose of via a licensed waste disposal contractor. Contaminated absorbent
material may pose the same hazard as the spilt product. Note: see Section 1 for
emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling : Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.

Date of issue : 01.12.2020 4/11

SteelMaster 60SB

Section 7. Handling and storage

Conditions for safe storage, : Store in accordance with local regulations. Store in a segregated and approved
including any incompatibilities area. Store in original container protected from direct sunlight in a dry, cool and well-
ventilated area, away from incompatible materials (see Section 10) and food and
drink. Store locked up. Eliminate all ignition sources. Separate from oxidizing
materials. Keep container tightly closed and sealed until ready for use. Containers
that have been opened must be carefully resealed and kept upright to prevent
leakage. Do not store in unlabelled containers. Use appropriate containment to
avoid environmental contamination. See Section 10 for incompatible materials
before handling or use.

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits

xylene Ministry of Labor (Thailand, 8/2017).

TWA: 100 ppm 8 hours.
ethylbenzene Ministry of Labor (Thailand, 8/2017).
TWA: 100 ppm 8 hours.
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace
procedures atmosphere or biological monitoring may be required to determine the effectiveness
of the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to appropriate monitoring
standards. Reference to national guidance documents for methods for the
determination of hazardous substances will also be required.

Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust
controls ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapour or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and
safety showers are close to the workstation location.
Eye/face protection : Safety eyewear complying to EN 166 should be used when a risk assessment
indicates this is necessary to avoid exposure to liquid splashes, mists, gases or
dusts. If contact is possible, the following protection should be worn, unless the
assessment indicates a higher degree of protection: chemical splash goggles.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.

Date of issue : 01.12.2020 5/11

SteelMaster 60SB

Section 8. Exposure controls/personal protection

There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.
Wear suitable gloves tested to EN374.
Not recommended, gloves(breakthrough time) < 1 hour: butyl rubber
May be used, gloves(breakthrough time) 4 - 8 hours: neoprene, PVC
Recommended, gloves(breakthrough time) > 8 hours: nitrile rubber, 4H, Teflon,
polyvinyl alcohol (PVA)

Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
If workers are exposed to concentrations above the exposure limit, they must use a
respirator according to EN 140. Use respiratory mask with charcoal and dust filter
when spraying this product, according to EN 14387(as filter combination A2-P2). In
confined spaces, use compressed-air or fresh-air respiratory equipment. When use
of roller or brush, consider use of charcoalfilter.

Section 9. Physical and chemical properties

Appearance
Physical state : Liquid.
Colour : White.
Odour : Characteristic.
Odour threshold : Not available.
pH : Not applicable.
Melting point : Not applicable.
Boiling point : Lowest known value: 136.1°C (277°F) (ethylbenzene). Weighted average: 136.14°C
(277.1°F)
Flash point : Closed cup: 24°C (75.2°F)
Burning time : Not applicable.
Burning rate : Not applicable.
Evaporation rate : Highest known value: 0.84 (ethylbenzene) Weighted average: 0.79compared with
butyl acetate
Flammability (solid, gas) : Not applicable.
Lower and upper explosive : 0.8 - 6.7%
(flammable) limits
Vapour pressure : Highest known value: 1.2 kPa (9.3 mm Hg) (at 20°C) (ethylbenzene). Weighted
average: 0.98 kPa (7.35 mm Hg) (at 20°C)
Vapour density : Highest known value: 3.7 (Air = 1) (xylene). Weighted average: 3.7 (Air = 1)

Date of issue : 01.12.2020 6/11

SteelMaster 60SB

Section 9. Physical and chemical properties

Relative density : 1.349 g/cm³
Solubility : Insoluble in the following materials: cold water and hot water.
Partition coefficient: n-octanol/ : Not available.
water
Auto-ignition temperature : Lowest known value: 432°C (809.6°F) (xylene).
Decomposition temperature : Not available.
SADT : Not available.
Viscosity : Kinematic (40°C): >0.205 cm2/s (>20.5 mm2/s)
Aerosol product

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.
Chemical stability : The product is stable.
Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions
Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurise, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Incompatible materials : Keep away from the following materials to prevent strong exothermic reactions:
oxidising agents, strong alkalis, strong acids.
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
xylene LC50 Inhalation Vapour Rat 20 mg/l 4 hours
LD50 Oral Rat 4300 mg/kg -
TDLo Dermal Rabbit 4300 mg/kg -
melamine LD50 Oral Rat 3161 mg/kg -
ethylbenzene LC50 Inhalation Vapour Rat - Male 17.8 mg/l 4 hours
LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
xylene Eyes - Mild irritant Rabbit - 87 milligrams -
Skin - Mild irritant Rat - 8 hours 60 -
microliters
melamine Eyes - Mild irritant Rabbit - 24 hours 500 -
milligrams
Sensitisation
Not available.
Mutagenicity
Not available.
Carcinogenicity
Not available.
Reproductive toxicity
Not available.
Teratogenicity
Not available.

Date of issue : 01.12.2020 7/11

SteelMaster 60SB

Section 11. Toxicological information

Specific target organ toxicity (single exposure)
Name Category Route of Target organs
exposure
xylene Category 3 Not applicable. Respiratory tract
irritation
Specific target organ toxicity (repeated exposure)
Name Category Route of Target organs
exposure
ethylbenzene Category 2 Not determined hearing organs

Aspiration hazard
Name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1

Potential acute health effects

Eye contact : Causes serious eye irritation.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation.
Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Inhalation : Adverse symptoms may include the following:
reduced foetal weight
increase in foetal deaths
skeletal malformations
Ingestion : Adverse symptoms may include the following:
reduced foetal weight
increase in foetal deaths
skeletal malformations
Skin contact : Adverse symptoms may include the following:
irritation
redness
reduced foetal weight
increase in foetal deaths
skeletal malformations
Eye contact : Adverse symptoms may include the following:
pain or irritation
watering
redness

Potential chronic health effects

General : No known significant effects or critical hazards.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : Suspected of damaging fertility.

Numerical measures of toxicity

Acute toxicity estimates
Route ATE value
Dermal 5726.59 mg/kg
Inhalation (vapours) 75.75 mg/l

Date of issue : 01.12.2020 8/11

SteelMaster 60SB

Section 11. Toxicological information

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
ethylbenzene Acute EC50 7.2 mg/l Algae 48 hours
Acute EC50 2.93 mg/l Daphnia 48 hours
Acute LC50 4.2 mg/l Fish 96 hours

Persistence and degradability

Product/ingredient name Aquatic half-life Photolysis Biodegradability
xylene - - Readily
ethylbenzene - - Readily

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
xylene 3.12 8.1 to 25.9 low
melamine -1.22 <3.8 low
ethylbenzene 3.6 - low

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction. Waste packaging should be recycled. Incineration or
landfill should only be considered when recycling is not feasible. This material and
its container must be disposed of in a safe way. Care should be taken when
handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Vapour from product
residues may create a highly flammable or explosive atmosphere inside the
container. Do not cut, weld or grind used containers unless they have been cleaned
thoroughly internally. Avoid dispersal of spilt material and runoff and contact with
soil, waterways, drains and sewers.

Section 14. Transport information

UN IMDG IATA
UN number UN1263 UN1263 UN1263

UN proper shipping Paint Paint Paint

name

Date of issue : 01.12.2020 9/11

SteelMaster 60SB

Section 14. Transport information

Transport hazard 3 3 3
class(es)

Packing group III III III

Environmental No. No. No.
hazards
Special precautions Transport within user’s Transport within user’s Transport within user’s
for user premises: always transport in premises: always transport in premises: always transport
closed containers that are closed containers that are in closed containers that are
upright and secure. Ensure upright and secure. Ensure upright and secure. Ensure
that persons transporting the that persons transporting the that persons transporting the
product know what to do in product know what to do in product know what to do in
the event of an accident or the event of an accident or the event of an accident or
spillage. spillage. spillage.
Additional - Emergency schedules F-E, The environmentally
information S-E hazardous substance mark
may appear if required by
other transportation
regulations.

Transport in bulk according to : Not available.

Annex II of Marpol and the
IBC Code
ADR / RID : Tunnel restriction code: (D/E)
Hazard identification number: 30
ADR/RID: Viscous substance. Not restricted, ref. chapter 2.2.3.1.5 (applicable to
receptacles < 450 litre capacity).
IMDG : IMDG: Viscous substance. Transport in accordance with paragraph 2.3.2.5
(applicable to receptacles < 450 litre capacity).

Section 15. Regulatory information

Hazardous Substance Act B.E. 2535 (1992)
Type
Ingredient name Type Authority Conditions

No known specific national and/or regional regulations applicable to this product

(including its ingredients).

Section 16. Other information

History
Date of printing : 01.12.2020
Date of issue/Date of revision : 01.12.2020
Date of previous issue : 28.05.2020
Version : 1.09
Key to abbreviations : ADN = European Provisions concerning the International Carriage of Dangerous
Goods by Inland Waterway
ADR = The European Agreement concerning the International Carriage of
Dangerous Goods by Road
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods

Date of issue : 01.12.2020 10/11

SteelMaster 60SB

Section 16. Other information

MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
RID = The Regulations concerning the International Carriage of Dangerous Goods
by Rail
UN = United Nations
LogPow = logarithm of the octanol/water partition coefficient
References : Not available.
Indicates information that has changed from previously issued version.
Notice to reader
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical
experience. Jotun's products are considered as semi-finished goods and as such, products are often used under
conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product
variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the
given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs and
specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue : 01.12.2020 11/11