Performance Series IR 1080p IP PTZ Dome Quick Installation Guide

800-22755 - Rev A - 12/2016 10. REPLACEMENT PARTS - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric shock
Cautions and Warnings or other hazards. Using replacement parts or accessories other than the original
manufacturers may invalidate the warranty.

CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of

used batteries in accordance with local laws.

Before You Begin

WARNING Installation and servicing should be performed only by qualified and Check that you have received all of the parts listed below. If any parts are missing or
experienced technicians to conform to all local codes and to maintain your warranty. damaged, contact your dealer immediately.

WARNING To ensure compliance with electrical safety standards, CSA Certified/UL HDZP252DI • PTZ dome camera • Waterproof joint
Listed Class 2 power adapters are required. Power over Ethernet (PoE) shall be supplied • Mount • Quick Installation Guide
by listed Information Technology Equipment. The PoE is not intended to be connected to • Wrench • Installation CD
exposed (outside plant) networks.

IMPORTANT NOTE Note Rotate and remove the protective cover bag and tape from the camera body
Regarding PoE operation of HDZP252DI models before the installation.
A high power PoE injector capable of supplying at least 20 W is required for proper
operation of HDZP252DI models.

FCC Statement of Compliance Inserting the SD Card

Information to the User: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
Open the camera cover and insert an SD card into the camera before starting installation
designed to provide reasonable protection against harmful interference when the
(if an SD card is required).
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Open rear cover
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

Note Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
SD card slot
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

Manufacturer’s Declaration of Conformance

The manufacturer declares that the equipment supplied with this guide is compliant with
the European Parliament and Council Directive on the Restrictions of the use of certain
Hazardous Substances in electrical and electronic equipment (2011/65/EU), General
Product Safety Directive (2001/95/EC) and the essential requirements of the EMC
Directive (2014/30/EU), conforming to the requirements of standards EN 55022 for
emissions, EN 50130-4 for immunity, and EN 60950-1 for electrical equipment safety.

WARNING To comply with EN50130-4 requirements, a UPS should be employed

when powering the camera from 12 V DC.
It is recommend that you use a high quality microSD card (up to 128 GB) that has a
minimum write speed of class 10. Insert the card before finishing camera installation. The
Waste Electrical and Electronic Equipment (WEEE) card must be formatted using the Honeywell Web GUI before it can be used for recording
(go to Setup  Storage  Destination  Local  Format).
Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable local
laws, regulations, and procedures.

Safety Instructions
Before installing or operating the unit, read and follow all instructions. After
installation, retain the safety and operating instructions for future reference.
1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
2. INSTALLATION
• Install in accordance with the manufacturer’s instructions.
• Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
3. POWER SOURCES - This product should be operated only from the type of power source
indicated on the marking label.
4. HEAT - Situate away from items that produce heat or are heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers).
5. MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer,
or sold with the product.
6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as
they may result in the risk of fire, electric shock, or injury to persons.
7. ACCESSORIES - Only use accessories specified by the manufacturer.
8. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
9. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.

Document 800-22755 – Rev A – 12/2016

Installing the Wall IMPORTANT NOTE
Regarding PoE operation of HDZP252DI models
Mount and PTZ
A high power PoE injector capable of supplying at least 20 W is required for proper
The wall mount weighs 1.46 lb operation of HDZP252DI models.
(0.66 kg) and can be installed
directly to a load-bearing wall, or
to a corner or pole using an
appropriate adapter.
Resetting the Camera
Important Notes:
• Ensure that the mounting
surface can support the Press and hold the reset button for 10 seconds when the camera is powered on to reset
combined weight of the the camera (refer to below image for reset button location).
camera and the mount (at
least 10.58 lb [4.8 kg]).
• If you are using a microSD
card, install the card first (not
supplied, refer to Inserting
the SD Card on page 1).
• When you attach the mount
to the wall in step 2, please
make sure the mount is fixed
to the wall with appropriate
material and is kept stable.
Open rear cover
The PTZ is so heavy that it
might drop when you attach
it to the mount with the
security chain (step 3).
1. Feed the cables through the
mount, leaving
approximately 0.5 ft (0.15 m)
extending past the end of the
Reset button
mount.
2. Attach the mount to the wall
using appropriate hardware.
3. Connect the
security chain to
the eyelet of the
wall mount.
4. Loosen the three Before Logging On to the Camera
M6 stainless
locking screws.
5. Connect the Before logging on to the camera, ensure that Internet Explorer is set up to run ActiveX
cables using the controls. You can enable ActiveX controls manually or by setting the browser’s security
waterproof joint settings to the default level.
(see image
inset).
ActiveX Controls and Plugins Settings Internet Security Level
6. Screw the dome
camera onto the 1. Open Internet Explorer. 1. Open Internet Explorer.
wall mount and
tighten the three 2. On the Tools menu, click Internet 2. On the Tools menu, click Internet
locking screws. options, and then click Security. options, and then click Security.

3. Click the Internet icon, and then 3. Click the Internet icon, click
click Custom level. Default level and click OK.

4. Set all ActiveX controls and plug- 4. Close the browser window and
ins to Prompt or Enable, and then open a new one to access the
click OK. camera.
Cable Connections

Before connecting the cables, take a minute to familiarize yourself with the cables, as
shown in the figures and table below. Logging On to the Camera
Power (12 V DC)
If the camera is connected to the PoE port of a Honeywell Embedded NVR, you can log
on to the camera directly from the NVR.
Network: Ethernet
To log on to the camera from a PC:
Audio
1. Install the Honeywell Config Tool from the installation CD.

Alarm 2. Use the Config Tool to discover the camera and open the camera’s webpage.
3. Log on to the camera as the admin user. The default user name is admin (case-
sensitive) and the default password is 1234.
Power Barrel Connector 12 V DC
Network RJ45
Red Audio OUT
Audio White Audio IN
Black Audio GND
Blue Alarm OUT 1
Green Alarm COM 1 Outputs (x1): Relay output,
20 V DC, 1 A max. Use alarm
Alarm Red Alarm IN 1 outputs for SELV circuits only.
Brown Alarm IN 2 Inputs (x2): 5 V, pull up.
Yellow & Green Alarm GND

Note The Ethernet cable should not be longer than 328 ft (100 m).

Document 800-22755 – Rev A – 12/2016

Configuring the PTZ Dome

The following figure shows the basic controls on the Live page:

Time display Live video functions

Live video window Camera type

setup

Refer to the Performance Series IR 1080p IP PTZ Dome Camera User Guide for detailed
instructions on how to configure the camera using the web client.

Recommended Recorders

The following table lists the Honeywell Embedded NVRs recommended for use with
Performance Series IR 1080p IP PTZ dome cameras:

HEN081*4 8ch, 2 HDD, 8 PoE, 4K, H.265

HEN161*4 16ch, 2 HDD, 16 PoE, 4K, H.265

HEN321*4 32ch, 2 HDD, 16 PoE, 4K, H.265

HEN162*4 16ch, 4 HDD, 16 PoE, 4K, H.265

HEN322*4 32ch, 4 HDD, 16 PoE, 4K, H.265

HEN642*4 64ch, 4 HDD, 16 PoE, 4K, H.265

HEN163*4 16ch, 8 HDD, 16 PoE, 4K, H.265, RAID 5&6

HEN323*4 32ch, 8 HDD, 16 PoE, 4K, H.265, RAID 5&6

HEN643*4 64ch, 8 HDD, 16 PoE, 4K, H.265, RAID 5&6

* Storage in TB
 Honeywell Security Products Americas Honeywell Security Northern Europe
(Head Office) Ampèrestraat 41
2700 Blankenbaker Pkwy, Suite 150 1446 TR Purmerend, The Netherlands
Louisville, KY 40299, USA www.honeywell.com/security/nl
www.honeywell.com/security  +31 (0) 299 410 200
 +1 800 323 4576

Honeywell Security Europe/South Africa Honeywell Security Deutschland

Aston Fields Road, Whitehouse Industrial Johannes-Mauthe-Straße 14
Estate 72458 Albstadt, Germany
Runcorn, WA7 3DL, United Kingdom www.honeywell.com/security/de
www.honeywell.com/security/uk  +49 (0) 7431 801-0
 +44 (0) 1928 754 028

Honeywell Security Products Americas

Caribbean/Latin America Honeywell Security France
9315 NW 112th Ave. Immeuble Lavoisier
Miami, FL 33178, USA Parc de Haute Technologie
www.honeywell.com/security/clar 3-7 rue Georges Besse
 +1 305 805 8188 92160 Antony, France
www.honeywell.com/security/fr
Honeywell Security Pacific  +33 (0) 1 40 96 20 50
Level 3, 2 Richardson Place
North Ryde, NSW 2113, Australia
www.asia.security.honeywell.com
 +61 2 9353 7000 Honeywell Security Italia SpA
Via della Resistenza 53/59
Honeywell Security Asia 20090 Buccinasco
35F Tower A, City Center, 100 Zun Yi Road Milan, Italy
Shanghai 200051, China www.honeywell.com/security/it
www.asia.security.honeywell.com  +39 (0) 2 4888 051
 +86 21 2219 6888

Honeywell Security Middle East/N. Africa

Emaar Business Park, Sheikh Zayed Road Honeywell Security España
Building No. 2, Office No. 301 Avenida de Italia, n° 7, 2a planta
Post Office Box 232362 C.T. Coslada
Dubai, United Arab Emirates 28821 Coslada, Madrid, Spain
www.honeywell.com/security/me www.honeywell.com/security/es
 +971 (0) 4 450 5800  +34 902 667 800

www.honeywell.com/security
+1 800 323 4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-22755 – Rev A – 12/2016
© 2016 Honeywell International Inc. All rights reserved. No part of this publication may be
reproduced by any means without written permission from Honeywell. The information in this
publication is believed to be accurate in all respects. However, Honeywell cannot assume
responsibility for any consequences resulting from the use thereof. The information contained herein
is subject to change without notice. Revisions or new editions to this publication may be issued to
incorporate such changes. For patent information, see www.honeywell.com/patents.