Operating manual

2553.8041-10
Amarex KRT

Submersible motor pumps

Series
Amarex KRT

Size DN 100...DN 300

23 4...65 4 (4pol.)
20 6...50 6 (6pol.)
Motor size 10 8...21 8 (8pol.)

Material types G, GH

Works-No.: see nameplate

The operating manual contains important information and

hazard/danger warnings. It is imperative to read the instructions
set out in the manual prior to installation, making electrical
connections and commissioning. Additional operating instructions
relating
to the components of this plant will also have to be observed.

In principle if any work has to be carried out to the plant all electrical
supplies (inclusive of the control cable) should be disconnected at the
mains supply switch. The plant has to be safeguarded against accidental
starting.

Ident-No. 01 053 562

KSB
KSB Amarex KRT
These operating instructions contain important notes for the individual
material versions of the below sizes:
Contents Page
1. General 3

Type Size Material version 2. Safety 3

F, E, K = 2.1 Identification of symbols used
impeller type Cast iron within the operating manual 3
2.2 Personnel skills and training 3
G G1 G2 GH
2.3 Dangerous practices - non-observance of
F,E,K 100 - 401 F, E, K F, K F F, K safety instructions 3
F,E,K 150 - 401 F, E, K F F F
2.4 Safe working methods 3
2.5 Safety instructions for operators 3
K 151 - 401 K K -- K 2.6 Safety instructions during maintenance,
K 200 - 330 K K inspection and installation 3
2.7 Unauthorized modifications to the pump 4
E,K 200 - 401 E, K K
and fitting of spare parts
K 250 - 370 K K 2.8 Impermissible modes of operation 4
K 250 - 401 K K
3. Transport and interim storage 4
K 300 - 380 K K 3.1 Transport 4
K 300 - 381 K 3.2 Storage/conservation 4

4. Description of pump 4
4.1 General description 4
4.2 Identification data 4
4.3 Construction 4
4.4 Ancillary equipment 5

5. Assembly/Installation 5
5.1 Safety regulations 5
5.2 Checking procedure prior to commencement
of the installation 5
5.3 Installation 5
5.4 Connection of the pipeline 5
5.5 Electrical connection 6
5.6 Assembly kit installation 7

6. Start up/shut down 8

6.1 Initial start up of pump 8
6.2 Limitations of the operating range 8
6.3 Shutdown / storage / preservation 9
6.4 Re-starting pump after storage 9

7. Service and maintenance 9

7.1 General instructions 9
7.2 Service/Inspection 10
7.3 Drainage / Disposal 11
7.4 Dismantling 11
7.5 Re-assembly 12
7.6 Stockkeeping of spare parts 13

8 Trouble-shooting 14

9. Appendix 15

2
KSB Amarex KRT
1. General 2.2 Personnel skills and training
This KSB pump has been developed in accordance with the latest Operators, as well as service, inspection and assembly personnel
technology, it was manufactured with great care and is subject to must have proof of having the appropriate skills to carry out such
constant quality control. work. Area of responsibility, allocation and supervision of the
The operating manual is designed to introduce the pump to you, personnel must be controlled by the operator. Should the personnel
and to make operation easier and to make full use of all its not have the required knowledge, training must be arranged. If
applications. required, the operator can arrange such training to be carried out
The operating manual contains important information to ensure by the manufacturer/supplier. The operator must also ensure that
safe, correct and economic operation. It is imperative to observe the instruction manual is fully understood by the personnel.
the contents of the operating manual to ensure reliability and long
operating life of the pump and to avoid dangerous practices. 2.3 Dangerous practices - non-observance of safety
The operating manual does not take into account any local instructions
regulations which have to be complied with by the operator or by Non-compliance with the safety instructions can endanger people‘s
any hired installation staff. lives, the environment and the pumps.
This pump must never be operated outside the limits laid down in In detail, non-compliance could, for example, cause the following:
the technical documentation with regard to pumped media, rate of
flow, speed, density, pressure and temperature, including motor - Failure of pump/plant to operate
rating or contrary to any other instructions stipulated in the
operating manual or contract documentation. - Failure of servicing and maintenance methods
The nameplate states series/size, the most important operating - Endangering people by contact with electrical, mechanical and
data and the Works No./Serial No., which must always be stated chemical matters
when making enquiries, subsequent orders and especially when
ordering spare/replacement parts. - Contamination of the environment by leakage of dangerous
Should any additional information or instructions be required, or if substances.
there is any damage to the equipment, then please contact your
nearest KSB service. 2.4 Safe working methods
2. Safety The operator must observe all safety instructions outlined in this
This operating manual contains basic instructions, which must be leaflet, the existing national safety precautions to prevent
observed during installation, operation and servicing. Therefore it is accidents, and also any inter-company working, operating and
imperative that this manual is read prior to assembly by the fitter safety regulations.
and relevant skilled staff/and operators, and it must always be kept
within the locality of the machine/plant. 2.5 Safety instructions for operators
Do not only observe the general safety notes under this section,
but as well any other notes regarding safety included in the - If hot or cold machine parts are considered a danger, then these
manual. parts must be protected where contact is possible.
- Safety equipment to prevent contact with hot or cold movable
2.1 Identification of symbols used within the parts must not be removed while the machine is in operation.
operating manual
- Leakages (for example at shaft seals) of dangerous media (e.g.
The symbols contained within this manual calling attention to explosive, poisonous, hot liquids) must be disposed of in such a
situations where non-observance could endanger lives, are manner as to avoid any danger to personnel and environment.
especially identified such as:
- Danger caused by electric supply must be eliminated (in this
respect, see details of any regulations enforced by individual
countries of the VDE and/or local power supply stations).

2.6 Safety instructions during maintenance,

inspection and installation
Warning sign in accordance with DIN 4844 – W9
Calling attention to electric current with The operator bears the responsibility to ensure that all service,
inspection and maintenance work is carried out by authorized and
fully trained personnel, who have read and are familiar with the
operating instructions.
Basically, all work to the plant should only be carried out when the
machine is not operating. The operating instructions relating to the
method of switching off the equipment must be adhered to without
fail.
Warning sign in accordance with DIN 4844 – W8 Pumps or plants pumping dangerous media must be
Safety instructions relating to situations where non-observance decontaminated.
could damage the machine and its functions are identified with the Once maintenance work is completed, all safety equipment must
word be reinstated again and checked to ensure they function correctly.
Read and follow the point listed in the paragraph 6.1 prior to
Attention installation.

Any instructions which are actually printed on the machine such as:
- arrow indicating the direction of rotation
- identification for fluid connections

must be observed without fail and be kept clean and legible.

3
KSB Amarex KRT
2.7 Unauthorized modifications to the pump and 4.2 Identification data
fitting of spare parts
Identification can be found on the nameplate, which is fitted to the
Modifications to the pump can only be carried out after motor. Illustration nameplate for non-flameproof and flameproof
authorization has been obtained from the manufacturer. Original design see appendix: ”General pump outline” Fig 1.
spare parts and ancillary equipment supplied by the manufacturer
provide safety. Installation of any other equipment cancels the KRT F 100-401 / 50 4 X G - 390
guarantee for any pump failure which occurs as a result of installing
Series
non-manufacturer‘s parts.
Impeller type (E,F,K)
2.8 Impermissible modes of operation
E = single-vane impeller
Operating safety of the equipment is only guaranteed if all F = free-flow impeller
operating instructions as outlined in paragraph 1 - General - are K = non-clogging impeller
observed. The limits given in the data sheet must under no
Hydraulic size
circumstances be exceeded.
Motor size
3 Transport and interim storage Number of poles
The chain or lifting wire which is supplied must 4-pole
only be used for lifting the appropriate pump 6-pole
unit. General use for lifting heavy loads is not 8-pole
permitted. Motor version (U, W, X)

U = standard version
Do not lift the pump by the motor cable. W = hot water design (max. 60 °C)
X = explosionproof version T3
The pump must be handled carefully during
transport. The chain or lifting wire must be
attached securely at the pump and crane end. Material version / variants
Personnel can be injured and the pump unit (G, G1, G2, GH)
damaged should the pump slip out of the
chain/guide rope. G = Pump complete in cast iron Grauguß
G1 = GG Pump with impeller in duplex steel (1.4517)
3.1 Transport G = GG Pump with impeller in chilled casting (0.9635)
GH = Pump manufactured in chilled casting ( 0.9635)
The motor housing/cover of the pump has been prepared for
attaching the chain supplied with the unit. For lifting the unit during Impeller diameter
unpacking only this prepared fixing should be used for attaching
the lifting chain.

4.3 Construction
4.3.1 Driver
KSB submersible pump sets are supplied with three-hase
asynchronous motors complete with connecting cable.
Electrical data in compliance with nameplate. Starting method
standard: direct or Y∆.

4.3.1.1 Motors in flameproof design

In accordance with EN 50014/ EN 50018; Protection type EEx d IIB
T3.
4.3.2 Shaft seal
The shaft seal consists of a mechanical seal which is independent
of the direction of rotation at pump and motor end. The oil
chamber which is fitted between the two mechanical seals ensures
cooling and lubrication.

4.3.3 Bearing assembly

All sizes are fitted with grease-lubricated, maintenance-ree deep-
3.2 Storage/conservation groove anti-riction bearings.
The procedure has been outlined in paragraph 6.3 ”Shutdown”.

4. Description of pump
4.1 General description
KSB submersible pumps are close-coupled units which are non-
self-priming. The impellers in these pumps can vary, depending on
the impeller type required by the customers to suit a particular
application. Usually, the pumps are operated fully submerged. For
short periods, they may run dry until the minimum filling level is
reached.

4
KSB Amarex KRT

Free-flow impeller (F-impeller) for pumping 5.3.1 Checking of operating data

liquids containing larger solid particles and
A check must be carried out to ensure that the details stated on the
fibres liable to twist and bunch and also gas
nameplate correspond to the order and pump data (for example
and air inclusions. operating voltage, frequency and pumped media temperature etc.).

Single-vane impeller (E-impeller) for pumping 5.3.2 Oil level control

lliquids containing larger solid particles and The oil chambers of our submersible pumps were filled with
fibres liable to twist and bunch, and also for environmentally safe non-toxic paraffin oil at works.
the damage-free transport of solids.
The oil level must be checked prior to initial operation of the
unit.
Closed non-clogging impeller (K-impeller) for Procedure see item 6.1.1
contaminated, non-gaseous liquids 5.3.3 Checking of the direction of rotation
containing solids, without fibres liable to twist
Before starting with the installation, make sure that the direction of
and bunch.
rotation is the correct one, acc. to para. 5.5.6.
5.4 Connection of the pipeline
4.3.4 Impeller types (Appendix ”General outline-installation set” Fig 1).
The discharge pipe must be connected to the pump without tension.
4.3.5 Installation methods
Under no circumstances must the pump be
- stationary wet-well installation Attention
- transportable installation used as an anchoring point for the pipeline.

For detailed installation description, see item 5.6.

Any expansion of the pipes caused by high temperatures must be
4.3.6 Dimensions adjusted by taking appropriate corrective measures, to ensure that the
pump does not come under undue stress due to pipeline forces and
Information regarding dimensions and weight can be found in
torques.
Appendix "Dimension tables”.
Excessive pipeline forces can cause leakages of
4.4 Ancillary equipment pumped media for example. Toxic and hot media
Suitable KSB switchgears are available to ensure trouble-free can endanger life.
functioning of the monitoring equipment. Recommended equipment is
described in Appendix ”Electrical connection diagram”
Any information relating to other ancillary equipment will be given by When emptying objects on a lower level, a non-return valve must be
our Sales Office. fitted into the discharge pipe to avoid backflow from the channel,
which could be led via the backflow level (road level) upwards and only
then into the sewage channel.
5. Assembly/Installation
Screwed pipeline joints where plastic parts
5.1 Safety regulations Attention were used, must not be damaged by careless
handling of tools during the installation of
It is not permitted for any person to enter the tank pump and pipeline.
during operation of the pump unless special safety
Fitting of a non-return valve is also essential for longer rising pipes to
precautions have been taken in accordance with
avoid excessive backflow when the pump is turned off. Ensure that
current safety regulations.
ventilation is taken into account when fitting a non-return valve.

5.2 Checking procedure prior to commencement of

the installation

Construction lay-out must be in accordance with measurements set

out on the table of dimensions. The construction of the concrete
foundations should be sufficiently strong (min. B 25 in accordance
with DIN 1045) to ensure a secure and functionally correct installation
in compliance with DIN 1045 or equivalent standard. Concrete
foundations must have set before installation of the unit. Its surface
must be level and even.

5.3 Installation
Examine the unit carefully prior to commencement of installation
regarding any damage incurred to the unit and cabling during
transport. Before installation of the pump all items listed in paragraph
6.1 have to be checked in sequence. A separate nameplate stating
pump and motor data is supplied within the scope of supply. This
nameplate must be fixed in a clearly visible position outside the tank
(for example switch panel, pipework, mounting bracket).

5
KSB Amarex KRT
5.5 Electrical connection 5.5.4 Overcurrent relay
General The motor must be protected against overloading by a thermally
retarded overcurrent relay to comply with VDE 0660 / IEC 947 and
The electrical connection must be carried out regulations which are in accordance with local requirements. This
by a trained electrician and in compliance with must be adjusted to the nominal motor current indicated on the
local regulations. The voltage must comply nameplate.
with the voltage indicated on the nameplate.
5.5.5 Level control switch
Electrical installation must be in accordance with the appendix
”Electrical connection diagrams” for the appropriate motor sizes. Pumping stations with automatic pump operation should be fitted with
The pump is delivered with cable. a level control switch. The cut-off point should be set as ‘R’ in
accordance with Appendix ”Dimension tables”.
Do not remove the protective cover, which is This prevents an interruption of the delivery by the pump which would
Attention situated at the cable gland until immediately cause dry running.
before installation.
5.5.6 Checking of the direction of rotation
The individual cores of the cable ends bear marking tapes (e.g. U(T1). Once the electrical connections are complete, the following should be
V(T2), W(T3), 21, 22, or 10, 11, ...) checked:
If cables have to be shortened, take care of the core index or colour
imprints. In such a case, remove the core marking and reaffix it The pump cannot reach its duty point if the
afterwards. Attention direction of rotation is incorrect. Non-
observance can lead to damaging the pump
When laying an earth cable between the set.
Attention pumping station and the electrical switchgear,
an additional multi-core control cable (min. 1.5
2
mm ) must be installed for motor monitoring Prior to carrying out any tests check that there
equipment and float switch control. Adjust are no foreign objects within the pump casing.
cores to suit requirement. Never put hands or any objects into the pump.

5.5.1 Monitoring equipment

The unit has been supplied with monitoring equipment to prevent The running time should be as short as
overloading. Installation, description and functioning of the monitoring Attention possible (max 3 minutes).
equipment can be taken from Appendix ”Electrical connection
diagrams”. Correct direction of rotation:
5.5.2 Frequency inverter operation If the phase sequence of the circuit is known, the correct direction of
rotation will occur automatically, providing the instructions in 5.5 have
In case of using frequenzy converters, the power output of the motor been carried out correctly (rotating of the motor to the left). The
P2 is limited to direction of rotation is checked by short starts and observations of the
- 85 % of nominal value, if a voltage source converter (VSC) is used, impeller.
- 95 % of nominal value, if a current source converter (CSC) is used. When looking at the pump mouth, the impeller must move to the left
(with some pumps, the direction of rotation is marked by an arrow).
5.5.3 Fitting of electric cabling (see appendix ”General pump outline” Fig. 6).

After installing the unit, it is advised to If the direction of rotation is incorrect, interchange 2 of the
Attention position the motor cable straight upward in 3 phases in the switch cabinet.
order not to have it affected by the swirl 5.5.7 Connection of a potential equaliser
created by the pumped liquid.
For potential equalisation, follow the instructions to EN 60 204.
For correct installation of the electric cabling within the pump sump
The potential-equalising conductor is connected to the external
(Appendix ”General pump outline” Fig. 5) we recommend using
connection terminal at the cable entry.
cable socks, which can be supplied as an additional extra (paragraph
4.4). Slack installation of cables could cause damage to the electric (Appendix ”General pump outline”).
cabling because of vibrations when the pump is operating. Special requirements for chemically corrosive media
Fitting of cable protection sheath Do not use the outside terminal if the unit is used for chemically
Attention corrosive media and with a flameproof pump.

If a protection sheath is included in the scope of supply for the electric Instead, the potential equaliser should be fitted to a flange at the
cabling, it has to be fitted according to the instructions given in the discharge pipe, which does not come into contact with the media.
supplementary operating manual „Assembly of protection sheath“. Please ensure that there is an electrical connection between the newly
created potential equaliser and the pump.
(Appendix ”General pump outline” Fig. 5).

6
KSB Amarex KRT
5.6 Assembly kit installation 2. Fit threaded bolt 904 with clamping piece 571/ support piece 572
to the mounting bracket. Do not unscrew hexagonal nut 920.36
The following assembly kits are available for assembly/installation of too much, just enough to allow sufficient play for tightening the
the KRT pump unit. cable subsequently. Ensure that the two clamping pieces 553 are
fitted correctly to a support piece.
- 5.6.1 Stationary wet-well installation
- 5.6.2 Transportable installation 3. The duckfoot bend should be positioned and secured to the base
of the sump so that the tightened cable will run vertically later on.
5.6.1 Stationary installation/guide cable Should construction/pipework etc. require the cable to run off the
o
5.6.1.1 Description vertical, then a maximum angle of 5 should be adhered to, thus
ensuring safe fitting function.Securing of the duckfoot bend is
(Appendix ”General outline-installation set“ Fig. 1) carried out by using bolts or foundation bolts regardless of pump
size or material variation.
Stationary installation provides the facility to insert and lift out the Units larger than approx. 2,000 kg in weight are supplied
pump unit at any time regardless of liquid level within the sump by complete with foundation slide rails. Refer to Appendix
means of a double guide cable. ”Dimension tables” and Appendix ”Wet-well installation
with parts list” for details relating to appropriate fitting
Guided securely by two parallel, previously tightened stainless steel
instructions and hole dimensions.
cables the pump slides into the well or tank and attaches itself to the
duckfoot bend which has been fitted to the bottom. 4. Insertion of cable and fitting. Lift thrust plug and clamp and insert
The weight of the pump acts as seal between pump and duckfoot one end of the cable. Lead the cable around the duckfoot bend
bend. A profile joint between pump and duckfoot bend achieves a 72–1 and back again towards the guide bracket and insert into
pressure-proof elastic connection. clamp of thrust plug. Manually tension the cable and secure by
Walking on the well is not permitted during inspection and using hex. nuts 920.37.
maintenance work.
5. Tighten the cable by fastening the hexagonal nut 920.36 situated
5.6.1.2 Scope of supply for stationary wet-well on top of the mounting bracket(s). Tighten the hexagonal nut with
installation a torque of MA as outlined in the table Appendix ”Guide cable
tension” to achieve sufficient cable tension. Subseqently secure
Please refer to the Appendix ”Wet-well installation with parts by using a second hexagonal nut.
list”
6. The loose end of the cable at the clamp 572 can either be twisted
5.6.1.3 Installation of pump with claw into a ring or the end can be cut off. After length adjustment, seal
connection off ends to avoid fraying.
Use appendix ”Wet-well installation” with parts list for guidance. 7. Place shackle 59-18 into the mounting bracket 894 to enable the
lifting chain to be attached at a later stage.
1- Prior to lowering the pump fit claw 732 to the discharge flange of
the pump housing.
Table Bolt tightening torque ”Steel anchor bolt”
Screws have to be tightened in accordance with the instructions.
This is described under item 7.5.1 in the table ”Bolt tightening Size (ø, mm) Torque (Nm)
torque”. 10 10
2. Fit profile seal 410.35 or 99-6 into the groove of the claw/pump 18 80
casing flange. This profile seal will serve to seal the duckfoot
bend during installation.
Table Bolt tightening torque ”Foundation bolt”
5.6.1.3 Fitting of the mounting bracket/duckfoot bend/ Size (ø, mm) Torque (Nm)
guide cable
12 25
Construction of the base/concrete foundations should be sufficiently 16 65
strong (min. B 25 in accordance with DIN 1045) to ensure a 20 125
functionally correct fixing of guide cable equipment and duckfoot
bend. 24 210

Refer to the drawing as illustrated in Appendix ”Wet-well

installation with parts list‘for all installation tasks outlined below. Table ”Guide cable - tension”
Size MA P
1. Secure mounting bracket 894 using anchor bolt 90-3.37 at the (Nm) (N)
sump opening rim. Borehole diameter and depth for the anchor 100-401 200-330 14 6 000
bolt to be taken from Appendix ” Dimension tables”. Bolt 150-401 200-401
tightening instructions are outlined in the table below. 151-401
250-370 300-381 30 10 000
Up to size 200-401, all means of fixation are part of the scope of 250-401
supply. Fixations for larger sizes have to be carefully selected by 300-380
the owner of the plant and must be adapted to his conditions at
site.
For the bolt of the mounting bracket refer to Appendix MA = tightening torque
”Dimension tables”. P = cable tension

7
KSB Amarex KRT

5.6.1.5 Fitting of chain / lifting rope 6. Start up/shut down

stationary wet-well installation
Installation of this equipment should be carried out in accordance with It is important to fulfil the following
the ”General pump outline”, Fig. 2a by inserting the chain/lifting Attention requirements. Any damage incurred as a
rope into the opposite the outlet branch. Further details can be found result of non-compliance is not covered by the
in ”Wet-well installation with parts list”. guarantee.
This type of fixing achieves a forward inclination of the pump towards Do not pump any media which is unsuitable
the outlet branch and permits the fitting of the pump to the duckfoot Attention for the material outlined in the technical
bend. documentation.

5.6.1.6 Installation of the pump 6.1 Initial start up of pump

(Appendix ”General outline installation set” Fig. 1) Prior to starting the pump it has to be ascertained that the following
The pump is lowered into the sump by guiding it from above over the points have been checked and executed:
clamp 572. It is then attached to the guide cable and slowly lowered - Operating data must be checked to comply with paragraph
into the sump. Once the pump is lowered, it will attach itself to the 5.3.1,Oil level paragraph 6.1.1 and direction of rotation paragraph
duckfoot bend 72-1 and is then securely fixed to the outlet pipe ready 5.5.6.
for use. Finally, attach the chain or rope to the shackle 59-18 on the
mounting bracket - Check that the installation of the electrical supply was carried out
correctly in accordance with Appendix: ”Electrical connection
5.6.1.7 Connection of the pipeline diagrams”.
(Appendix ”General outline installation set ”, Fig. 1) Temperature monitoring in the winding
Attention protects the motor in case of insufficient
For procedure, see para. 5.4. cooling conditions (e.g. if pump is partially not
5.6.2 Transportable installation submerged). Reliable operation and explosion
protection can only be guaranteed if the
5.6.2.1 Description circuits for temperature monitoring function
properly.
Pumps for transportable installation are supplied with a pump stand.
The outlet flange with DIN connections can be used for fitting either - Ensure that the pump has been installed correctly to comply
rigid or flexible piping. Examples for typical installation possibilities with installation kit paragraph 5.6.
can be taken from Appendix ”General outline installation set” Fig.
- Should the pump have been out of service for a long period,
2. Ancillary equipment can be requested and purchased from our
then the steps outlined in paragraph 6.4 must be carried out.
sales offices.

5.6.2.2 Components/extent of supply for 6.1.1 Oil level check

transportable installation Procedure according to appendix „General pump outline“
For parts supplied and detailed illustration, see Appendix ”Wet-well
Fig. 3. Remove screwed plug with joint ring 411.03. The oil level must
installation transportable with parts list”
be at the height of the oil inlet. If it is lower, fill the oil chamber via feed
opening until overflow. Regarding oil quality and quantity, see point
5.6.2.3 Assembly kit installation 7.2.4 (Oil change).
Please refer to drawing in Appendix ”Wet-well installation Tighten screwed plug with joint ring again.
transportable with parts list” for assembly.
6.2 Limitations of the operating range
The base plate or the pump stand must be fitted prior to installing the
pump. All screws must be tightened according to instructions. Refer 6.2.1 Minimum liquid level
to table ”Bolt tightening torque” paragraph 7.5.1 for instructions.
The pump is ready for operation when the liquid level has reached
5.6.2.4 Assembly chain/lifting rope/ measuring mark ”R”.
transportable installation This minimum liquid level also applies to pumping stations with
Fitting of chain/lifting wire should be carried out as outlined in automatic pump operation.
Appendix ”Wet-well installation transportable with parts list”. (Appendix ”General pump outline” Fig. 7)
Always use the slot which is fitted on the discharge side, see ”R” = Lowest switch-off point for automatic operation
Appendix ”General pump outline” Fig. 2b. ”M” = Minimum liquid level for constant operation

5.6.2.5 Installation of pump Built-in temperature controls within the winding will protect the motor
from overheating. If the motor overheats (for example during long
Transportable installation permits to operate the pumps in different operation with a completely exposed motor), the built-in temperature
locations. controls will switch off the motor and turn it on again automatically
For example, they can be used for draining minesthe emergency after cooling down.
draining of canals pumping water out of rivers etc. For such The control system must provide a protection against dry running by
applications the pump must be installed in a vertical position with the stopping the pump automatically (cut-off contact, see 5.5.5).
motor on the top and fitted to a firm base.
Dry running leads to increased wear (and tear)
Attention and should be avoided.

8
 KSB Amarex KRT
6.2.2 Temperature of pumped media and 6.3.2 Measures for prolonged shutdown periods
surroundings
1. The pump remains installed ready for operation when
KRT .... type X flameproof version 40 OC required.
1)
In order to secure pump availability as and when required and to
KRT .... type U 40 OC or avoid formation of deposits within the pump and the immediate
as indicated pump surroundings, the plant should be switched on for brief
on data plate periods (approx. 1 minute) once every month.
1)
KRT .... type W 60 OC or 2. The pump is dismantled and stored
as indicated
on data plate Prior to storage the pump should be checked and maintained in
1) o
accordance with paragraph 7.1 and 7.2. Subsequently, the
Can be operated up to 80 C for a limited period (3–5 min. or until preservation outlined in paragraph 6.3.1 must be carried out.
the thermal protection equipment is activated)

Do not operate the equipment at temperatures 6.4 Re-starting pump after storage
Attention higher than those indicated above, unless the Prior to re-starting the pump, all checks and maintenance steps
manufacturer has given written consent. outlined in paragraphs 7.1 and 7.2 have to be carried out.
Damage caused due to non–observance of
this warning will not be covered by the Always disconnect all electricity supplies prior to
guarantee. working at the pump. Safeguard the pump from
being started accidentally. Otherwise, there will be
6.2.3 Switching frequency danger to life.

In order to avoid intolerably high temperature rises within the motor

and excessive overloading of motor, seals and bearings, the following In addition, free-running of the impeller should be
number of switching operations per hour (S) should not be exceeded: checked. This can be done by putting one hand
into the pump casing and manually turning the
impeller.
Motor capacity max. S
(kW) (Switching operations/h)
up to 7,5 30 When restarting the pump the items outlined in paragraph 6.1 and
from 7,5 10 paragraph 6.2 have to be observed.

6.2.4 Operating voltage Immediately after completion of the maintenance

work, all safety and protection equipment has to
The maximum admissible deviation of the operating voltage amounts be installed expertly and must be set working.
to ± 10%, with flameproof versions to ± 5% of the rated voltage. The
maximum admissible voltage difference between the single phases
amounts to 1%. 7. Service and maintenance
6.2.5 Density of pumped media 7.1 General instructions
Power input of the pump increases directly with the density of the The operator must ensure that all maintenance, inspection and repair
pumped medium. To avoid overloading of the motor this density must work is carried out by qualified, authorized staff who are familiar with
comply with the data stated in the order. the equipment and who have read the operating instructions.

6.2.6 Abrasive media By compiling a maintenance plan it is possible to cut maintenance

expenses and avoid extensive repair costs, thus achieving trouble-free
When pumping media containing abrasive particles, increased wear and reliable operating of the pump.
of hydraulic and mechanical seals must be expected. The
Always disconnect all electricity supplies prior to
maintenance intervals must be halved compared to those usually
working on the pump. Safeguard the pump from
recommended (as outlined in paragraph 7). In addition, it is
being started accidentally.
recommended to limit the flow velocity in relation to the rising main to
Otherwise, there will be danger to life.
> 1.5 m/sec < 5 m sec in order to achieve the maximum operating
periods possible.
If the pumped media are harmful, the pump must
6.3 Shutdown/storage/preservation be decontaminated. Special care should be taken
to prevent an endangering of personnel and
If operation is not required until some time after delivery, we
environment when draining leakage liquid/oil. All
recommend the following steps for storage of the pump:
official regulations must be adhered to.
6.3.1 Storage of new pumps
- Spray the inside of the pump housing with oil by paying special
attention to the area around the impeller gap. Spray oil through inlet
and outlet flanges. It is then recommended to protect the flanges (with
plastic caps or similar).
- Store the pump in an upright position in a dry place. Support all
electrical cables at cable entry points to avoid permanent distortion.
- Electric connecting cables are capped securely for protection
purposes prior to delivery. This protection must not be removed.

9
KSB Amarex KRT
7.2 Service/Inspection 7.2.3 Checking the monitoring equipment
The following points must be observed to ensure reliable The performance tests should form part of general periodic
operation: maintenance work, carried out every 4,000 hours or at least
annually.
This work must only be carried out by experienced personnel!
a) Temperature switch – Check resistance between the
connection ends 21 and 22: R < 1 Ω
Item Maintenance tasks Maintenance to b) PTC–resistor sensor– resistance measuring –
be carried out at resistance between connection ends 10 and 11:
following 100 Ω < R < 750 Ω
intervals
7.2.1 Insulation resistance check If the given tolerances are exceeded, disconnect the electric
supply/control cable at the unit and check again directly at the
7.2.2 Visual inspection of electric cables every terminals of the unit. If tolerances are exceeded here, too, the winding
7.2.3 Check of monitoring equipment 4,000 hours must be replaced.
7.2.4 Oil change but at least c) Moisture protection electrode
7.2.5 Bearings and lubrication once a year The motor area is being monitored by a moisture monitoring electrode
7.2.6 Visual check of lifting chain / rope which is fitted into the motor area (Part No. 81-56). It is not always
General overhaul every 5 years fitted as standard. Core identification 9 will show whether or not it has
been fitted.
7.2.1 Insulation resistance check Instructions relating to performance and technical data can be found
in Appendix ”Moisture monitoring”.
The insulation resistance of the motor winding has to be
checked every 4,000 hours but at least once a year during The moisture monitoring electrode is okay if the insulation resistance
general maintenance. measured at the electrode is > 5 MΩ . Lower values indicate moisture
or even intrusion of water into the motor. In such cases, the motor
Measurements should be taken at the cable ends (disconnected at the needs to be opened and overhauled.
starting panel). The measurement should be taken by using a megger.
A new moisture sensor must be fitted in the event of damage.
– Measuring voltage: max 1,000 V d.c. voltage
d) Float switch - continuity check-
The insulation resistance of the motor winding with cable ends tied
together must not be less than 5 megohm. If measurements are less, The motor interior will be monitored by a built-in float switch which
then cable and motor must be checked separately. During the does not always form part of the standard scope of supply. Core
measurement procedure the supply cable must be disconnected from identities 3 and 4 show whether it has been installed or not.
the motor. Resistance between connection ends 3 and 4: R < 1 Ω .
If resistances exceed these values, check for leakage. If there is no
The measurements to be taken are:
leakage in the motor interior, but the resistance amounts to > 1 Ω ,
a) Winding against earth contact your nearest KSB Service.
- All winding ends connected with each other
b) Winding temperature sensor against earth
- All cable ends of the winding temperature sensors should be
connected to one another and all winding ends be connected
to earth
If the insulation resistance for the electric supply cable is less than 5
megohm, this indicates damage and needs replacement.
Low reading of the insulation resistance values of the motor indicates
that there is a fault in the winding. If this is the case, contact either the
manufacturer or the nearest KSB Agent/Distributor.

7.2.2 Inspection of the electric cable

- Visual inspection of the electric cable.
Whenever the pump is inspected, the electrical supply cables
should also be checked with regard to damage such as cracks
or bubbles, due to either mechanical or chemical causes. If
such damage is detected, then all electric cables must be
replaced.
- Checking the protection cable. Measurement of the
resistance between the cores should be R < 1 Ohm.

10
KSB Amarex KRT
7.2.4 Oil change 7.2.5 Bearing and lubrication
The oil chamber of our submersible pump has been filled with The pump/motor shaft is supplied with grease-lubricated ball
environmentally friendly, non-toxic paraffin oil of medical quality on bearings.
the pump end.
However, the oil should be changed after 4,000 operating 7.2.6 Visual check of lifting chain / lifting rope
hours, but at least annually. Maintenance checks to the pump should also include the lifting
Pumped liquid might enter the oil chamber when it chain/lifting rope inclusive of fitting to the pump with regard to
is warm after operation, which can cause a possible damage - caused either mechanically or chemically.
pressure rise within the chamber. It is, therefore, Damaged parts must be replaced by manufacturer‘s original spare
advisable to cover the filling plug 903 (with a cloth) parts.
during the opening process to avoid hot liquid This also refers to the correct fixing of the lifting chain/lifting rope to
(squirting out) escaping. the pump.

Procedure 7.3 Drainage/Disposal

(Appendix ”General pump outline”) If the pump has been used to pump
Attention hazardous media, care must be taken that,
Erect the pump as shown in Fig. 3 and put a suitable container when draining the leakage liquid/oil filling,
under the plug. Unscrew screwed plug 903.03 with joint ring 411.03 personnel and environment are not
„oil filler plug“and 903.05/411.05 „oil drain“and drain the oil. endangered. All government regulations
The oil is light in colour and transparent in appearance. Slight have to be observed.
discolouring, caused by running in of new mechanical seal or small
7.4 Dismantling
leakage of dirt via the pumped media will have no adverse effect.
Severe contamination of the oil by the pump media, however, 7.4.1 Basic guidelines and instructions
indicates damaged mechanical seals. In this case, replace the
mechanical seal. All repair and maintenance work to the pump must only be carried
out by especially trained straff, and original replacement parts
Screw in screwed plug 903.05 with joint ring 411.05. must be used.
Refilling The safety precautions as outlined in paragraph 7.1 and 7.4.4 have
Erect the pump as demonstrated in Fig. 3 and fill the oil chamber to be observed.
with oil until overflow (see also paragraph 6.1.1). Replace the plug Dismantling and re-assembly may only be carried out in line
903.03 and fit a new gasket 411.03. with the appropriate sectional drawing. The sectional drawing
Oil quantity: and other instructions are detailed in the appendix . The
dismantling sequence should be carried out as outlined in the
The quantity of oil required amounts to 6,5 l. sectional drawing.
If there are any problems, please contact our service
Recommended quality of oil: department for advice.
Paraffinoil, free-flowing, Messrs. Merck No. 7174 or
equivalent,non-toxic.
This quality is harmless and as such complies with the regulations
applicable to food.
Alternative:
All non-alloyed and alloyed motor oils of classes SAE 10 W up to
SAE 20 W can be used for lubrication of the mechanical seals. With
regard to disposal all general Government regulations must be
observed.
Regional regulations have to be observed to
Attention the extent that the oil does not contaminate
the pumped media (for example drinking
water) and that safe disposal is guaranteed.
Otherwise, it is not permitted to fill the pump
with oil, but paraffin oil must be used for this
purpose.

11
KSB Amarex KRT
7.4.2 Preparing for dismantling Assembly of the pump takes place in reverse order of dismantling.
The drawing combined with the individual parts index should be used
Prior to dismantling the oil chamber is to be emptied. as a guide. All screws must be tightened during assembly as outlined
in the instructions. General instructions in this respect are outlined in
7.4.3 Dismantling the pump section the table below ”bolt tightening torque” and special points are
stated in the installation instructions.
Dismantling the pump section is carried out as illustrated in the
drawing (Appendix ”General arrangement drawing”). Special tools Table ”Bolt tightening torque”
are not required. The only exceptions relate to the impeller
dismantling/assembly process for the following sizes. Thread Torque (Nm)
A4-70 / 1.4462
7.4.3.1 Special points relating to the M5 4
dismantling of the impeller M6 7
M8 17
The impeller/shaft connection is achieved by a parallel seat with M 10 35
locating key. The impellers have been prepared to accept a special M 12 60
impeller withdrawing device. This can be purchased as a special tool M 16 150
from KSB.
M 20 290
Further details relating to procedures and references relating to M 24 278
special tools are outlined in the assembly instructions Appendix M 27 409
”Impeller mounting/dismantling ”. M 30 554

7.4.3.2 Dismantling of mechanical seal 7.5.2 Special points relating to components for
Exact instructions relating to fitting positions of the mechanical seals, re-assembly
either motor side or pump side, are outlined in Appendix
”Mechanical seal with parts list”. 7.5.2.1 Mechanical seal

7.4.4 Dismantling the motor component In principle, we recommend to use new manufacturer‘s spare parts for
mechanical seals. In this respect it should be noted:
Please ensure, when dismantling the motor part and the electric
connecting cabling, that core identifications are clearly marked for To achieve perfect performance, it is important to ensure that all parts
future reference during re-assembly. are immaculately clean and that greatest care is taken during the
fitting of the mechanical seal. Protectors of the moving surfaces must
- Special points for version ” X ” explosionproof not be removed until immediately before fitting the part. The surface of
the shaft must be perfectly clean and undamaged.
All other work affecting the flameproofness, such In principle to assist with the fitting of the bellows mechanical seal, the
as new windings and mechanical repairs at the inside of the bellows to avoid any damage to the mechanical seal
motor section, require a subsequent acceptance should be wetted with soapy water (do not use oil).
test by an approved engineer or have to be carried
out at the premises of the manufacturer. Attention: Fitting of the bellows mechanical seal at the motor end.
7.5 Re-assembly To avoid damage to the rubber bellows by a keyway or shaft recess,
the shaft stub should be covered with a thin sheet of foil (approx.
7.5.1 General instructions 0.1...0.3 mm thick). Push the rotating unit over foil cover and place
into fitting position. Then remove the foil.
Assembly of the pump must be carried out in accordance with the
current mechanical engineering regulations. All parts which were 7.5.2.2 Impeller assembly
dismantled must be cleaned and tested with regard to wear. Damaged
or worn parts must be replaced by using manufacturer‘s spare Instructions and procedures are outlined in Appendix ”Impeller
parts. Ensure that all sealing surfaces are clean and the O-rings or mounting/dismantling ”and in paragraph 7.4.3.
flat seals fit perfectly. We recommend the use of O-rings/seals at all
times.O–rings made from continuous strips which were glued 7.5.2.3 Checking seals
together must not be used.
After assembly the mechanical seal part/oil chamber should be tested
for leaks.

Procedure:
(Appendix ”General pump outline” Fig. 8)
The oil inlet tapping should be used to test for leaks.
Securely screw the testing device into the oil inlet opening.
Test media: Compressed air
Test pressure: max. 0.5 bar
Test duration: 2 min.
Make sure that the pressure does not decrease during the test.
Afterwards, fill the oil chamber (compare para. 7.2.4).

12
KSB Amarex KRT
7.5.2.4 Motor / electrical connections
Ensure prior to re-assembly of explosionproof motors that all the
special points outlined in paragraph 7.4.4 were observed.
All motors must be tested electrically in line with paragraph 6.1, 6.2
and 7.2.

7.6 Stockkeeping of spare parts

Always quote the following data when ordering spare parts:

Pump type: e.g. KRTF 100-401/504XG-390

Works-No./ Identity-No. fill in
Motor-No.

This data can be taken from the nameplate (appendix ”General

pump diagram” Fig. 1)

7.6.1 Recommended stock of spare parts for a two–

year operation in accordance with VDMA 24296
(applicable for continuous operation)

Part– Part description Number of pumps

No. (including stand-by pumps)
2 3 4 5 6 8 10
and
more
80-1 Part motor - - - 1 1 2 3
834 Cable entry 1 1 2 2 2 3 40%
818 Rotor - - - 1 1 2 3
230 Impeller 1 1 1 2 2 3 30%
502 Wear ring 2 2 2 3 3 4 50%
433.01 Mechanical seal 2 3 4 5 6 7 90%
motor side
433.02 Mechanical seal 2 3 4 5 6 7 90%
pump side
321.01 Grooved ball 1 1 2 2 3 4 50%
/322 bearing
motor side
320/ Grooved ball 1 1 2 2 3 4 50%
321.02 bearing
pump side
Set of joint rings 4 6 8 8 9 10 100%
(gasket)
motor

13
KSB Amarex KRT

8. Trouble-shooting
Unit not pumping
Pump delivers insufficiently
Current/power consumption too high
Head too low
Pump operation is uneven and noisy

Cause Remedy:
Prior to carrying out work to the pressure containing
parts - release pressure from the pump!
Disconnect power supply to the pump.
Pump delivers against excessively high discharge Open discharge valve further until duty point is
pressure reached
Valve in discharge pipe not fully open Open gate valve completely
Pump not running within operating limits Check operating data of the pump

Pump and/or pipeline are not completely vented or Vent - by lifting the pump off the duckfoot bend and
primed lowering it back again.
Pump inlet blocked by deposits Clean inlet, pump parts and non return valve
Inlet pipe or impeller blocked - rotor running sluggishly Remove deposits from within the pump and/or
pipelines
Dirt/fibres in impeller chambers Check impeller ensuring that it rotates slightly - if
necessary clean hydraulic
Wear of internal pump parts Replace worn parts
Damaged column pipe (pipe and seal) Replace defective column pipe
Renew seals
Unacceptable air or gas content within the pumped Contact your nearest authorized KSB agent
media
Oscillations caused by plant Contact your nearest authorized KSB agent
Wrong direction of rotation Switch two phases of the circuit cabling
Insufficient operating voltage Check electric supply
Check cable connections
Motor not running due to no voltage supply Check electrical installation
Inform electrical company
Motor running on two phases only Replace defective fuses
Check electric cable connections
Motor winding or electric cable defective Replace by new original KSB cabling or contact your
nearest authorized KSB agent
Radial bearing in the motor defective Contact your nearest authorized KSB agent
With star delta connection - Motor only running in star Check star delta connection
position
Water level dropping excessively during operation Check supply and capacity of system - (sump depth)
check level control
Temperature monitor for winding control has ceased to The motor will switch on automatically after cooling
operate due to excessively high winding temperature down
Thermistor release unit without automatic restart Check the pump
facility for temperature limit (flameproof) has been
released due to exceeding the permissible winding
temperature
Moisture protection relay has been released due to Check the pump
moisture within the motor
Attention: If working inside the pump is necessary whilst the pump is under warranty, then contact your
nearest authorized KSB agent prior to commencement of work. Non-observance will negate any
warranty claims.

14
KSB Amarex KRT

9. Appendix Page

• General Pump Outline 16

• General arrangement drawing with parts list 19

• Installation plan mechanical seal with parts list 22

• Dimension tables 24

• General outline - installation set 26

• General arrangement drawing Wet-well installation - guide cable with parts list 27

• Wet-well installation - transportable with parts list 29

• Electrical connection diagrams 31

• Operational diagram moisture monitoring 32

• Assembly instructions Impeller mounting/dismantling device 33

15
KSB Amarex KRT

General pump outline Amarex KRT

DN 100...DN 300
Motor
23 4...65 4; 20 6...50 6;
10 8...21 8

Diagram nameplate

Pump type

Works No. / Identity No.

Motor No.

Important information for ordering spare parts

explosionproof version

Pump type

Works No. / Identity No.

Motor No.

Identity No of
explosionproof certificate

Fig. 1

16
KSB Amarex KRT

Fig. 2a
Fig. 2b

903.03 Oil-priming plug

411..03

903..05 Oil-drain plug

411..05

Fig.3

81-29.02

Fig. 4

A
B
B

81-29.02

Fig. 5
17
 KSB Amarex KRT

Fig. 6

Fig. 7

Fig. 8

18
KSB Amarex KRT

General arrangement drawing 100-401

Motoren: 23 4...65 4 150/151-401
20 6...50 6 200-330
10 8...21 8 200-401
250-370
250-401
300-380
300-381

OW 382 429-00

19
KSB Amarex KRT

Part No. Part description

59-17 Shackle
811 motor casing
81-59 Stator
101 Pump casing
163 Discharge cover
230 Impeller
260 Impeller hub cap
321 Radial ball bearing
322 Radial roller bearing
330 Bearing bracket
411 Gasket
412 O-ring
421 Radial shaft seal ring
433 Mechanical seal
502 Casing wear ring
550 Washer
818 Rotor
834 Cable duct
900 Screw
902 Stud
903 Screwed plug
914 Socket head cap screw
920 Nut
932 Circlip
940 Key

20
KSB Amarex KRT

Installation plan - mechanical seal Amarex KRT

Motor: 23 4...65 4, 100/150/151-401

20 6...50 6, 200-330
10 8...21 8 200-401
250-370
250-401
300-380
300-381

Standard-mechanical seal
Part No Part description
433 Mechanical seal
550 Washer
433.01 932 Circlip

550.03

Special mechanical seal

932.03

433.02

433.02

550.44

21
KSB Amarex KRT
Dimension table Amarex KRT 100-401/150-401/151-401

Transportable Aufstellung
Stationäre Aufstellung
Transportable Installation
Stationary Installation
Installation transportable
Installation stationnaire

1) tiefster Ausschaltpunkt bei Automatikbetrieb 2) Mindestüberdeckung bei Dauerbetrieb

Lowest shut-off point for automatic operation Minimum covering for continuous operation
Point d’arret le plus bas en service automatique Recouvrement minimal pour service continu

Maße in mm 0W 382 433-00

Dimensions in mm
Cotes en mm

22
KSB Amarex KRT
Dimension table Amarex KRT 200-330/200-401

Stationäre Aufstellung Transportable Aufstellung

Stationary Installation Transportable Installation
Installation stationnaire Installation transportable

1) tiefster Ausschaltpunkt bei Automatikbetrieb 2) Mindestüberdeckung bei Dauerbetrieb

Lowest shut-off point for automatic operation Minimum covering for continuous operation
Point d’arret le plus bas en service automatique Recouvrement minimal pour service continu

Maße in mm 0W 382433-00
Dimensions in mm
Cotes en mm

23
KSB Amarex KRT
Dimension table Amarex KRT 250-370
250-401
300-380
300-381
Stationäre Aufstellung Transportable Aufstellung
Stationary Installation Transportable Installation
Installation stationnaire Installation transportable

1) tiefster Ausschaltpunkt bei Automatikbetrieb 2) Mindestüberdeckung bei Dauerbetrieb

Lowest shut-off point for automatic operation Minimum covering for continuous operation
Point d’arret le plus bas en service automatique Recouvrement minimal pour service continu

Maße in mm 0W 382 434-00

Dimensions in mm
Cotes en mm
24
KSB Amarex KRT

General outline-installation set

25
KSB Amarex KRT

Wet-well installation with guide cable Amarex KRT DN

Motor: 23 4, 29 4, 35 4, 50 4, 65 4 100 / 150 / 200 / 250 / 300

20 6, 26 6, 32 6, 40 6, 50 6
10 8, 17 8, 21 8

Epoxy resin tar Counter nut

coating

Motor:
35 4...65 6
59-17
22 6...50 6

Standard
Standard variants

99-6
902.35
920.35

90-3.38

26
KSB Amarex KRT

K 250-370
K 250-401
K 300-380
K 300-381

59-24.01

72-1
Z V

900.38

0W 380772-00

0W 380

27
KSB Amarex KRT

Part No. Part description

59-17 Shackle
59-18 Hook
59-24.01/02 Rope
72-1 Flanged bend
90-3 Dowel
99-6 Round cord
550 Washer
553 Thrust insert
571 Clamp
572 Clamp
732 Holder
885 Chain
894 Bracket
900 Screw
901 Hexagon head bolt
902 Stud
904 Threaded pin
914 Socket head cap screw
920 Nut

28
KSB Amarex KRT

Wet-well installation transportable Amarex KRT DN

Motor: 23 4, 29 4, 35 4, 50 4, 65 4 100 / 150 / 200 / 250 / 300

20 6, 26 6, 32 6, 40 6, 50 6
10 8, 17 8, 21 8

Epoxy resin tar coating

914.26
920.26 885
59-24.02

59-17
Z
914.26
920.26
885
Z 59-24.02
59-17
Motors
23 4, 29 4
20 6, 26 6
10 8, 17 8, 21 8

885
59-24.02

59-17

Motors
35 4, 50 4, 65 4
32 6, 40 6, 50 6
902.04
920.04
182

0W 309307-00

29
KSB Amarex KRT

Part No. Part description

182 Foot
59-17 Shackle
59-24 Rope
885 Chain
902 Stud
914 Socket head cap screw
920 Nut

30
KSB Amarex KRT

Electrical diagram

Motor: 23 4, 29 4, 20 6, 26 6, 10 8, 17 8, 21 8

Description - Thermal cutout Amarex KRT,

explosionproof
With explosionproof motors, the windings are protected by two
independent temperature monitoring circuits.
Two bimetal switches F4, F5 (identification tape 21,22) serve as Motor version X, Y
temperature monitoring devices which, as soon as the max. winding
temperature is reached, switch off the pump and automatically on
again after the windings have cooled down.
This requires that the conductors are directly connected to the
control circuit of the motor contactor.
Three PTC thermistors R1, R2, R3 (identification tape 10, 11) are
fitted as additional temperature controlslimiters which, in the event of
temperature switch failure, shut down the pump before the
temperature permissible for explosionproof applications is exceeded.
Automatic reset is not allowed.
A thermistor control unit „T“with manual reset must be installed in Motor version U, W
the control circuit of the motor contactors.
This equipment is of a commercial brand, which can also be
purchased via KSB.

For operation with frequency converter, a release device bearing the

test mark „PTB 3.53-PTC/A“must be used.

If the pump has been shut down by thermistors, it is necessary to

overhaul it.
In urgent cases the reset may be used after the motor has cooled
down. The thermistor must not be shut off at any time.
Explosionproof requirements for the pumps are only
met if the built-in temperature monitoring devices
(bimetal switches and thermistors) including
conductors 21, 22, 10, and 11 are connected.
Temperature switch
F4, F5 = Monitoring circuit = 2 bimetal switches in the motor
winding
Identification tape 21, 22
max. operating voltage of switch: 250 V
max. current: 2 A
R1,R2,R3 = Temperature control circuit = 3 PTC thermistors in
the motor winding
Identification tape: 10, 11
max.operating voltage on terminals
Umax = 30 V =
resistance between terminals 10/11
- at ambient temperature R 100-750 Ω
- at shutdown temperature R > 4000 Ω
Do not test monitoring circuits by means of a
Attention hand megger. Use an ohmmeter.

Description - thermal cutout Amarex KRT, non-explosionproof

The winding is protected by one temperature monitoring circuit.

Bimetal switches F4, F5 (identifications tape 21,22) are used for

temperature monitoring. It switches off the pump as soon as the
max. winding temperature is reached, and automatically switches it
on again after the winding has cooled down.

The bimetal switch must be directly connected to the control circuit

of the motor contactor.
Conductors 10 and 11 (used for explosionproof version only) will be
connected to dummy terminals.

31
KSB Amarex KRT

Electrical diagram

Motor: 35 4, 50 4, 65 4, 32 6, 40 6, 50 6

Description - Thermal cutout Amarex KRT,

explosionproof
With explosionproof motors, the windings are protected by two
independent temperature monitoring circuits.
Two bimetal switches F4, F5 (identification tape 21,22) serve as
temperature monitoring devices which, as soon as the max. winding
temperature is reached, switch off the pump and automatically on
again after the windings have cooled down.
This requires that the conductors are directly connected to the
control circuit of the motor contactor.
Three PTC thermistors R1, R2, R3 (identification tape 10, 11) are
fitted as additional temperature controls/limiters which, in the event
of temperature switch failure, shut down the pump before the
temperature permissible for explosionproof applications is exceeded.
Automatic reset is not allowed.
A thermistor control unit „T“with manual reset must be installed in
the control circuit of the motor contactors.
This equipment is of a commercial brand, which can also be
purchased via KSB.

For operation with frequency converter, a release device bearing the

test mark „PTB 3.53-PTC/A“must be used.

If the pump has been shut down by thermistors, it is necessary to

overhaul it.
In urgent cases the reset may be used after the motor has cooled
down. The thermistor must not be shut off at any time.
Explosionproof requirements for the pumps are only
met if the built-in temperature monitoring devices
(bimetal switches and thermistors) including
conductors 21, 22, 10, and 11 are connected.

Temperature switch
F4, F5 = Monitoring circuit = 2 bimetal switches in the motor
winding
Identification tape 21, 22
max. operating voltage of switch: 250 V
max. current: 2 A
R1,R2,R3 = Temperature control circuit = 3 PTC thermistors in
the motor winding
Identification tape: 10, 11
max.operating voltage on terminals
Umax = 30 V =
resistance between terminals 10/11
- at ambient temperature R 100-750 Ω
- at shutdown temperature R > 4000 Ω
Do not test monitoring circuits by means of a
Attention hand megger. Use an ohmmeter.

Description - thermal cutout Amarex KRT, non-explosionproof

The winding is protected by one temperature monitoring circuit.
Bimetal switches F4, F5 (identifications tape 21,22), are used for
temperature monitoring. It switches off the pump as soon as the
max. winding temperature is reached, and automatically switches it
on again after the winding has cooled down.

The bimetal switch must be directly connected to the control circuit

of the motor contactor.
Conductors 10 and 11 (used for explosionproof version only) will be
connected to dummy terminals.

32
KSB Amarex KRT

Operational diagram - Moisture monitoring

B2 B3

M Motor chamber / moisture

∼
detection
(see also „Electrical diagram“)

If water penetrates into the motor chamber, the built-in float switch
Motor chamber / moisture detection will open its contact. This will release an alarm or switch the motor
(see also „Electrical diagram“) off.

B3= float switch (break contact)

If moisture penetrates into the motor chamber, first of all, a current
core identification 3, 4
will be flowing from terminal 9 to earth via the built-in moisture
electrode. This leads to the triggering of the Fl fault current
protective switch fitted for monitoring the moisture electrode. nominal operating voltage 230 V ∼
The K4 auxiliary relay will drop and switch off the motor contactor. nominal operating current 1A
This switching does, however, not represent a fault current breaking capacity 100 VA
monitoring according to VDE 0100 / IEC 364.
After tripping the moisture monitoring the pump will have to be
overhauled.

Check of the moisture electrode

An insulation resistance test acc. to 7.2.1 has to be carried out.

If the insulation resistance is < 5 MΩ , the motor has to be opened,
inspected and overhauled.
After dismantling the pump restore or replace the moisture sensor.
To restore the sensor dry it in an oven for about 1 hour at
120 °C.
Thereafter, soak it in transformer oil.

WE RECOMMEND FITTING A NEW MOISTURE SENSOR IN

THE EVENT OF DAMAGE.

B2 = Moisture transmitter (electrode) inside the motor space

Identifications tape: 9
Operating voltage 110...250 V-a. c.
Nominal fault current 30-50 mA

F1 = Fault current protective switch

K4 = Auxiliary relay

33
KSB Amarex KRT

Assembly instructions - Impeller mounting/dismantling device Amarex KRT

100 / 150 / 151-401
200-330
200-401
250-370/401
300-380/381

Mounting/dismantling of impeller

Tools required:

Dismantling device Identity-No. 19 138 913

Offset screwdriver Identity-No. 00 588 089

DIN 911

Fig. 1

Necessary tools are to be taken from table 230

„Mounting/dismantling device“. 914.10 260
The impeller is mounted/dismantled by using the
special device illustraded in Fig. 2.

Dismantling
1. Loosen impeller fixation according to the appertaining
appendix „General drawing“.

Fig. 1 Unscrew impeller screw 914.10 and remove

impeller hub cap 260.

Dismantling the impeller Fig. 2b

2. Impeller 230 is removed by means of the

mounting/dismantling device.
For this purpose, screw hex. bolt, part 4, into shaft
end to avoid damage to the shaft thread.

Fit special impeller mounting/dismantling device by

screwing in part 2.
After that, screw down threaded bolt, part. 1, and
remove impeller.

Assembly Fig. 2a

1. Screw part 1of the impeller mounting device into the

shaft end of the pump unit in order to mount impeller
230.

2. After that, fit part 2 by screwing it down onto the

threaded bolt part 1.

3. Mount impeller fixation according to fig.1/2.

34
KSB Amarex KRT

35
KSB Amarex KRT

Subject to change without notice.

2553.8041-10 11/98

KSB Aktiengesellschaft
Industry and Water Engineering Pumps
KSB P. O. Box 200743 D-06008 Halle (Saale) . Turmstraße 92 D-06110 Halle (Saale)
Tel. (+49) 3 45 48 26-0 Fax (+49) 3 45 48 2646 99 . Telex 465211 ks d . http://www.ksb.de