ONT Configuration and Maintenance: Digital Egypt Youth Training Program

ONT Configuration and Maintenance
Digital Egypt Youth Training Program
National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

Agenda
Terminal Profile Types
Process of Adding an ONT
Example for Adding Various ONTs
ONT Maintenance and Query

ONU Registration Process
OLT ONU
SN request message
The OLT requests  Different ONUs have different physical
ONU SN.
SN response message distances from the OLT.
An ONT reports the SN obtaining
phase
SN.
 To synchronize all ONUs, the OLT must
The OLT allocates range the actual physical distance of
Assign OUN_ID message an ONU ID.
each ONU and add a different delay
Ranging Request compensation for each ONU according
message
Ranging response to the farthest logical distance.
Ranging: Calculates Ranging
message
Ranging_time the actual distance phase
message of each ONU.  In this way, the logical distances
between ONUs and the OLT are the
PWD request same, and all ONUs connected to a
Password authentication
message (optional)
PWD response The OLT allocates a Authenticatio GPON port are synchronized.
management GEM port ID. n phase
message
The OLT creates a
management OMCI channel.
Operation status

Terminal Profile Types
DBA profile:-
• Defines the upstream traffic parameters of the GPON, and binds to T- Line profile
CONTs to control the upstream traffic. DBA
Line profile:-
• Defines the bottom-layer line parameters of the ONT, such as the DBA OMCI FTTH
ONT
profile used by a T-CONT, GEM port ID, service mapping mode, service
type, QoS, and FEC encryption enabling status. Service profile
Service profile:-
• Defines the types and number of ONT ports, mapping between port IDs
and VLANs, and translation between multicast VLAN and VLAN.
• Referenced when the management mode for an ONT to be added is set to Line profile
OMCI. DBA
FTTB/C
• A service profile does not need to be configured for the MDU SNMP MDU
management mode.
SNMP profile:- SNMP profile
• When an upper-layer network manages devices through the NMS server,
you need to set SNMP parameters.

Management Modes of Various ONTs
• Terminal management modes
• OMCI: FTTH series
• Example: HG8247 (directly connected through a network cable and accessed on the WebUI by
visiting http://192.168.100.1)
• SNMP: FTTB/C series

• Example: MA5620 (remotely accessed from the OLT by telnet and managed in command line mode)

Querying DBA Profiles
• The system provides 9 default DBA profiles with IDs ranging from 1 to 9. These profiles provide typical traffic parameter values.
• You can query and modify the default DBA profiles but cannot delete them.
• When you query a specified DBA profile by specifying the profile ID or profile name, the system displays the detailed
information about the profile. When all DBA profiles are queried, the DBA profiles are displayed in a list.
huawei(config)#display dba-profile all
-----------------------------------------------------------------------------
Profile Type Bandwidth Fixed Assured Max. Binding Times
Number Compensation Bandwidth Bandwidth Bandwidth
-----------------------------------------------------------------------------
1 1 No 5120 0 0 0
2 1 No 1024 0 0 0
3 4 No 0 0 32768 0
4 2 No 0 1024 0 1
5 1 No 32768 0 0 0
6 1 No 102400 0 0 0
7 2 No 0 32768 0 0
8 2 No 0 102400 0 0
9 3 No 0 32768 65536 8
Note: The system provides 9 default DBA profiles with IDs ranging from 1 to
9.

DBA profile Add
• A T-CONT is a physical resource on an ONT, and can carry services only after being bound to a DBA profile.
• If the default DBA profiles cannot meet service requirements, run this command to add a DBA profile
• DBA-profile add command is used to add a DBA profile.
huawei(config)#dba-profile add profile-id

{profile-id<10,512>}:22
{profilename<K>|type1<K>|type2<K>|type3<K>|type4<K>|type5<K>}:profi
le-name
{profile-name<S><Length 1-33>}:2M
{type1<K>|type2<K>|type3<K>|type4<K>|type5<K>}:type3
{assure<K>}:assure
{assure-bandwidth<128,1235456>}:2048
{max<K>}:max
{max-bandwidth<128,1235456>}:4096

ONT Line Profile
• The ont-lineprofile command is used to enter the ONT line profile mode to configure the attributes
of an ONT line profile. If you enter the ONT line profile mode for the first time, a default profile is
generated.
• The system supports a maximum of 8K PON line profiles.
huawei(config)#ont-lineprofile gpon profile-id

{profile-id<1,8192>}:66
{<cr>|profile-name<K>}:profile-name
{profile-name<S><Length 1-32>}:ftth
huawei(config-gpon-lineprofile-66)#
Note: When you create a line profile or DBA profile, if you do not specify the profile ID, the
system automatically allocates the profile ID.

Binding Tcont to DBA profile
• tcont command is used to bind a T-CONT to a DBA profile.
• A T-CONT is a physical resource on an ONT, and can carry services only after it is bound to a DBA profile.
• After the binding succeeds, the T-CONT can provide flexible dynamic bandwidth assignment schemes according to
configurations in the DBA profile.
• T-CONT 0 is bound to DBA profile 1 by default in the ONT line profile.
• The DBA profile bound to T-COUNT0 cannot be modified. You can modify the binding relationships of other T-
CONTs.
• You can run the display ont-lineprofile command to query the information about ONT line profiles.
huawei(config-gpon-lineprofile-66)#tcont
{tcont-list<S><Length 1-13>}:2
{dba-profile-id<K>|dba-profile-name<K>}:dba-profile-id
{profile-id<1,512>}:22

Adding Gem-port
• gemport add command is used to add a GEM port.
• Before configuring the GPON access service, you must run this command to add a service transmission channel, that is, a GEM port.
• After a GEM port is added successfully, run the ont gemport bind command to bind it to a T-CONT of an ONT,
• Then run the ont gemport mapping command to set up the mapping between the GEM port and a user service flow.
• Then, the service flow can be carried by the GEM port.
huawei(config-gpon-lineprofile-66)#gem
{add<K>|delete<K>|mapping<K>|modify<K>}:add
{gem-index<0,1023>}:20
{service-type<E><eth,tdm>}:eth
{tcont<K>}:tcont
{tcont-id<0,127> }:2
{<cr>|cascade<K>|encrypt<K>|gem-car<K>|priority-queue<K>}:priority-
queue
{priority-queue<0,7>}:3

Mapping mode
• mapping-mode command is used to create the mapping between GEM ports and services on the ONT side, that is, to set up the mapping
between GEM ports and the data flows of the ONT user interface.
• GEM ports can carry services only after the mapping is set up using this command..
• By default, an ONT supports the VLAN mapping mode.
• Currently, only one mapping mode can be configured.
• display ont-lineprofile command to query the mapping mode supported by an ONT.
huawei(config-gpon-lineprofile-66)#mapping-mode
{iptos<K>|port-priority<K>|port-vlan-priority<K>|port-
vlan<K>|port<K>|priority<K>|vlan-priority<K>|vlan<K>}:vlan

Configure mapping between a GEM port and VLAN
• The gem mapping command is used to create the mapping between GEM ports and the services on the
ONT side, that is, to set up the mapping between GEM ports and the upstream data flows of the ONT
user interface.
• GEM ports can carry services only after the mapping is set up using this command.
huawei(config-gpon-lineprofile-66)#gem mapping
{gem-index<0,127>}:20
{mapping-index<0,7>}:0
{e1<K>|eth<K>|flow–
car<K>|iphost<K>|moca<K>|priority<K>|vlan<K>}:vlan
{vlan-id<0,4095> }:10
{<cr>|flow-car<K>|priority<K>}:

QOS Mode
• Run the config command to enter the global config mode, and then run the ont-lineprofile command to enter the ONT line
profile configuration mode.
• qos-mode command is used to configure the QoS mode in an ONT line profile, that is, the upstream traffic control mode of
the ONT.
• Run this command when you need to provide end-to-end quality assurance and control the traffic for a user.
• By default, the QoS mode of an ONT line profile is the priority queue scheduling mode.
• You can run the display ont-lineprofile command to query the QoS mode of a profile.
huawei(config-gpon-lineprofile-66)#qos-mode
{flow-car<K>|gem-car<K>|priority-queue<K>}:priority-queue
• commit command is used to commit the current parameter configurations of a service profile or line profile.
• When configurations are committed, the system checks the validity of the parameters of the service profile or line profile. If
the parameters pass the check, the system uses the new parameter configurations to update the system running data.
huawei(config-gpon-lineprofile-66)#commit
huawei(config-gpon-lineprofile-66)#quit

Querying an ONT Line Profile
huawei(config)#display ont-lineprofile gpon profile-id 66
-------------------------------------------------------
Profile ID :66
Profile name :ftth
Access type :GPON
------------------------------------------------------
Upstream FEC switch: Disabled
QoS mode :PQ
Mapping mode :VLAN
------------------------------------------------------
<T-CONT 0> DBA profile ID:1
<T-CONT 2> DBA profile ID:22
<GEM Index 20>
-----------------------------------------------------
|Service type :ETH | Downstream encryption: Off | Cascading attribute: Off |
Priority :0 |GEM-CAR:-
-----------------------------------------------------
Mapping index VLAN Priority Port type Port index Flow-CAR
------------------------------------------------------
0 10 - - - -
------------------------------------------------------
-------------------------------------------------------
Binding times :0

Adding a Service Profile for a Class A ONT
• Create a service profile and enter the profile configuration mode.
huawei(config)#ont-srvprofile
{epon<K>|gpon<K>}:gpon
{<cr>|profile-id<K>|profile-name<K>}:profile-id
{profile-id<1,4096>}:88
{<cr>|profile-name<K>}:profile-name
{profile-name<S><Length 1-32>}:hg8247
huawei(config-gpon-srvprofile-88)#

Configure ONT Port
• ont-port command is used to set the port capability set in an ONT service profile, that is, to set the number of various ports on an ONT.
• When setting the attributes of an ONT port in an ONT service profile, you need to check whether a port exists according to the specified
number of ports.
• If you do not use this command to set the number of ONT ports, the default number of all types of ports on the ONT is 0.
huawei(config-gpon-srvprofile-88)#ont-port
{catv<K>|eth<K>|moca<K>|pots<K>|tdm-srvtype<K>|tdm-
type<K>|tdm<K>}:eth
{eth-port<0,8>}:4
{<cr>|catv<K>|moca<K>|pots<K>|tdm-srvtype<K>|tdm-
type<K>|tdm<K>}:pots
{pots-port<0,8>}:2
{<cr>|catv<K>|moca<K>|tdm-srvtype<K>|tdm-type<K>|tdm<K>}:
• Set the ONT port VLAN

huawei(config-gpon-srvprofile-88)#port
{e1<K>|priority-policy<K>|q-in-q<K>|vlan<K>}:vlan
{eth<K>|iphost<K>|moca<K>}:eth
{ont-portlist<S><Length 1-128>}:1
{translation<K>|transparent<K>|vlanid<0,4095>}:10

• Configure the VLAN tag forwarding mode for multicast packets. (required only when multicast services are
used).
huawei(config-gpon-srvprofile-88)#multicast-forward
{tag<K>|unconcern<K>|untag<K>}:untag
• Configure the IGMP packet forwarding mode (required only when multicast services are used).
huawei(config-gpon-srvprofile-88)#igmp-forward
{translation<K>|transparent<K>|unconcern<K>}:unconcern
• Commit the configurations.

huawei(config-gpon-srvprofile-88)#commit
huawei(config-gpon-srvprofile-88)#quit
Note: All parameter settings take effect only after being committed.

Querying Service Profiles
huawei(config)# display ont-srvprofile gpon profile-id 88

---------------------------------------------------------------------
Profile ID: 88
Profile name: hg8247
Access type: GPON
---------------------------------------------------------------------
Port type Number of ports -------------------------------------
POTS 2
ETH 4
TDM 0
MOCA 0
CATV 0
---------------------------------------------------------------------
TDM type: E1
TDM service type: TDMoGem
MAC address learning: Enabled
ONT transparent transmission: Disabled
Multicast forwarding mode: Untag
Multicast forwarding VLAN: -
Upstream IGMP packet forwarding mode: Ignore
Upstream IGMP packet forwarding VLAN: -

Querying Service Profiles
---------------------------------------------------------------------
Port type Port No. QinQ mode Priority policy
---------------------------------------------------------------------
ETH 1 Ignore Ignore
ETH 2 Ignore Ignore
ETH 3 Ignore Ignore
ETH 4 Ignore Ignore
-----------------------------------------------------------------------
Port Type Port No. Service Type No. Service VLAN Service Priority User VLAN
-------------------------------------------------------------------------
ETH 1 Switch 1 1 - 1
IPHOST 1 Switch 1 1 - 1
------------------------------------------------------------------------
Number of binding times: 0

SNMP Profile
huawei(config)#snmp-profile
{add<K>|delete<K>|modify<K>}:add
{profile-id<K>|profile-name<K>|version<E><v1,v2c>}:profile-id
{profile-id<1,64>}:1
{profile-name<K>|version<E><v1,v2c>}:profile-name
{profile-name<S><Length 1-32>}:n2000
{version<E><v1,v2c>}:v2c
{readgroup<S><Length 1-32>}:public
{writegroup<S><Length 1-32>}:private
{des-ip<X.X.X.X>}:192.168.48.250
{source-port<1,65535>}:162
{securityname<S><Length 1-32>}:private

Terminal Configuration Process
Start
Appropriate DBA No
Add a DBA profile.
profile available?
Yes
Appropriate line No
Add a line profile.
profile available?
Yes
No
Appropriate service
Which ONU type? Add a service Profile.
profile available?
FTTH ONT
Yes
MDU
Add an ONT and bind it to An FTTH ONT requires both a line

Related profiles.
profile and service profile.
An MDU requires only a line profile.

Adding ONT
 Enable the function of

Automatic automatically discovering
PON ports.
(discovery mode)  Confirm the SN of the
automatically
ONT Adding
Manually add the SN of the

Manually
ONT.

1- Adding an ONT in Automatic Discovery Mode
• Enable the function of automatically discovering PON ports.
huawei(config)#interface gpon 0/8
huawei(config-if-gpon-0/8)#port
{portid<0,7>}:0
{fec<K>|ont-auto-find<K>|ont-password-renew<K>|range<K>}:ont-auto-
find
{switch<E><enable,disable>}:enable
• Query the discovered ONT.

huawei(config-if-gpon-0/8)#display ont autofind 0
------------------------------------------------
Number : 1
F/S/P : 0/8/0
Ont SN : 323031312E396A41
Password : 0x31323334353637383930(1234567890)
VenderID : HWTC
Ont Version : 130C4400
Ont SoftwareVersion : V1R002C00S201
Ont EquipmentID : 245
Ont autofind time : 2011-04-19 09:59:53+08:00
------------------------------------------------
The number
National Telecommunication of GPON autofind ONT is 1
Institute ‫المعهد القومي لالتصاالت‬
Confirm the discovered ONT.
huawei(config-if-gpon-0/8)#ont confirm
{portid<0,7>}:0
{all<K>|ontid<K>|password-auth<K>|sn-auth<K>}:ontid
{ontid<0,127>}: 8
{password-auth<K>|sn-auth<K>}:sn-auth
{sn<S><Length 13-16>}:323031312E396A41
{omci<K>|password-auth<K>|snmp<K>}:omci
{ont-lineprofile-id<K>|ont-lineprofile-name<K>}:ont-lineprofile-id
{profile-id<1,4096>}:66
{ont-srvprofile-id<K>|ont-srvprofile-name<K>}:ont-srvprofile-id
{profile-id<1,4096>}:88
{<cr>|desc<K>}:
Note: The entered SN must belong to an automatically discovered ONT.

2- Adding an ONT Manually
huawei(config-if-gpon-0/8)#ont add
{portid<0,7>}:0
{ontid<0,127>|password-auth<K>|sn-auth<K>}:8
{password-auth<K>|sn-auth<K>}:sn-auth
{sn<S><Length 13-16>}:323031312E396A41
{omci<K>|password-auth<K>|snmp<K>}:omci
{ont-lineprofile-id<K>|ont-lineprofile-name<K>}:ont-lineprofile-id
{profile-id<1,4096>}:66
{ont-srvprofile-id<K>|ont-srvprofile-name<K>}:ont-srvprofile-id
{profile-id<1,4096>}:88
{<cr>|desc<K>}:
huawei(config-if-gpon-0/8)#display ont info 0 all

---------------------------------------------------------------
Subrack/Slot/Port ONT SN Control flag Running flag Configuration
status Matching status DBA mode
---------------------------------------------------------------
0/8/0 8 323031312E396A41 Activated Online Normal Match SR
0/8/0 10 323031312E396341 Activated Online Normal Match SR
---------------------------------------------------------------

ONU Activation
Configuration
(FTTH)
ONT Data Planning
Device Type HG8247
OLT PON port 0/8/0
ONT_ID 1
SN 323031312E396A41
Management mode OMCI
ont-lineprofile ID 91, name hg8247

ID 91, name hg8247
ont-srvprofile
4 Ethernet ports and 2 POTS ports

ONT Service Data Planning
DBA
Service User User GEM TCONT
Type Port VLAN ID Port ID ID
ID and Name Bandwidth
IP HOST Type 1; fixed

Voice 172 1 1 21, ftth_voip
1 Mbps
Type 2;
Internet
ETH 1 11 2 2 22, ftth_hsi Assured 2
access
Mbps
Type 3;
Assured 4
Multicast ETH 2 200 3 3 23, ftth_iptv
Mbps; Max. 8
Mbps
Adding an ONT Without Services
• 1-Configure an ONT line profile
huawei(config)#ont-lineprofile gpon profile-id 91 profile-name
hg8247
• 2-Configure an ONT service profile.
huawei(config)#ont-srvprofile gpon profile-id 91 profile-name hg850

huawei(config-gpon-srvprofile-91)#ont-port eth 4 pots 2

• 3- Add an ONT after automatic discovery.
huawei(config-if-gpon-0/8)#port 0 ont-auto-find enable
huawei(config-if-gpon-0/8)#ont confirm 0 ontid 1 sn-auth
323031312E396A41 omci ont-lineprofile-name hg850 ont-srvprofile-
name hg8247
huawei(config-if-gpon-0/8)#display ont info 0 all
--------------------------------------------------------
Subrack/Slot/Port ONT ID SN Control flag Running flag
Configuration status Matching status DBA mode -------
-------------------------------------------------
0/8/0 1 323031312E396A41 Activated Online Normal Match SR
----------------------------------------------------------

Adding ONT Service Configurations
• 1- Configure DBA profiles.
• Configure a DBA profile for the voice service.
huawei(config)#dba-profile add profile-id 21 profile-name ftth_voip
type1 fix 1024
• Configure a DBA profile for the Internet access service.

huawei(config)#dba-profile add profile-id 22 profile-name ftth_hsi
type2 assure 2048
• Configure a DBA profile for the video service.
huawei(config)#dba-profile add profile-id 23 profile-name ftth_iptv

type3 assure 4096 max 8112

2- Configure an ONT line profile.
huawei(config)#ont-lineprofile gpon profile-id 91
3- Bind a T-CONT to a DBA profile.

huawei(config-gpon-lineprofile-91)#tcont 1 dba-profile-id 21
4- Add a GEM port and map it to a T-CONT.

huawei(config-gpon-lineprofile-91)#gem add 1 eth tcont 1
5- Configure the mapping between GEM ports and service VLANs.

huawei(config-gpon-lineprofile-91)#gem mapping 1 1 vlan 172

6- Configure an ONT service profile
huawei(config)#ont-srvprofile gpon profile-id 91
huawei(config-gpon-srvprofile-91)#port vlan iphost 172
huawei(config-gpon-srvprofile-91)#port vlan eth 1 11
huawei(config-gpon-srvprofile-91)#port vlan eth 2 200

ONU Activation
Configuration
(MDU)
ONT Data Planning
Device Type MA5620G
OLT PON port 0/8/0
ONT_ID 2
SN 323031319C46B841
Management mode SNMP
OLT management VLAN 4000, upstream port 0/19/0, static IP

In-band address 192.168.2.254/24
management IP
address ONT management VLAN 4000, static IP address
192.168.2.2/24
ID 92, name ma5620
In-band management: TCONT ID 0
ont-lineprofile
In-band management: GEM port ID 0 buffered to TCONT0
In-band management: GEM port ID 0 mapped to VLAN 4000
ONT Service Data Planning
DBA
Service User GEM TCONT
User Port ID and
Type VLAN ID Port ID ID Bandwidth
Name
All 21, Type 1, fixed 1

Voice 172 4 1
ftth_voip Mbps
Type 2,
Internet 22,
ETH 1 11 5 2 assured 2
access ftth_hsi
Mbps
Type 3,
23, assured 4
Multicast ETH 2 200 6 3
ftth_iptv Mbps, max. 8
Mbps

Adding an ONT Without Services
• Configure an ONT line profile.
huawei(config)#ont-lineprofile gpon profile-id 92 profile-name
ma5620
• Add an ONT after automatic discovery.

huawei(config-if-gpon-0/8)# ont confirm 0 ontid 2 sn-auth
323031319C46B841 snmp ont-lineprofile-id 92
huawei(config-if-gpon-0/8)# display ont info 0 all
---------------------------------------------------------
Subrack/Slot/Port ONT ID SN Control flag Running flag
Configuration status Matching status DBA mode
---------------------------------------------------------
0/8/0 2 323031319C46B841 Activated Online Normal Match SR
-----------------------------------------------------------

Network Information
Service channel for

Upper-layer NMS
user management ROUTE or CLI terminal
between the OLT and R
ONT
In-band management
board
service
GPON
Control board
board
Upstream
channel between the
OLT and the upper-layer
network
CON
ETH In-band management
ESC VLAN and management
IP address of the OLT
In-band management Optical splitter MDU management mode:

IP address of the • 1. Issue the management IP address and
ONU ONU
VLAN in OMCI mode to set up an MDU
management channel.
PC
• 2. Use the in-band channel to telnet the MDU
or manage the MDU on the NMS.

In-band Management Configuration Process
Configure the in-band management VLAN.
Configure the in-band management address on

the OLT.
Configure the in-band management service

channel for an ONT.
Configure the in-band management address for

the ONT.
Test the connectivity.
Remotely log in to the ONT.

1- In-band Management
• Configure the in-band management VLAN on the OLT.

huawei(config)#vlan 4000 smart
huawei(config)#port vlan 4000 0/19 0
• Configure the in-band management IP address on the OLT.

huawei(config)#interface vlanif 4000
huawei(config-if-vlanif4000)#ip address 192.168.2.254 24
• Configure the in-band management service channel for the ONT.

• Configuring an ONT line profile.

• Configure the in-band service port for the ONT.
huawei(config)#service-port vlan 4000 gpon 0/8/0 ont 2 gemport 0

multi-service user-vlan 4000
• Configure the in-band management IP address for the ONT.
huawei(config-if-gpon-0/8)#ont ipconfig 0 2 static ip-address

192.168.2.2 mask 255.255.255.0 gateway 192.168.2.254 vlan 4000
• (Optional) Bind an SNMP profile (only when an NMS server is required).
huawei(config-if-gpon-0/8)#ont snmp-profile 0 2 profile-id 1

2- Testing the In-band Management Channel
• Test the in-band channel.
huawei(config)#ping 192.168.2.2
PING 192.168.2.2: 56 bytes, interrupt by CTRL-C.
Reply from 192.168.2.2: bytes =56 sequence number =1 survival time
=63 time = 10 ms
Reply from 192.168.2.2: bytes =56 sequence number =5 survival time
=63 time = 20 ms
• Remotely log in to the ONT

huawei(config)#telnet 192.168.2.2
{ <cr>|service-port<0,4294967295> }:
Command:
telnet 192.168.2.2
Run CTRL_] to exit telnet mode
Connecting to the 192.168.2.2...
Log in to the ONT and
Connected to the 192.168.2.2... configure services for
>>User name: root the ONT.
>>User password: mduadmin (ciphertext, invisible)

Adding ONT Service Configurations
• Configure an ONT line profile.
• Bind T-CONTs to the DBA profiles.

• Add GEM ports and map them to TCONTs.

• Configure the mapping between GEM ports and VLANs.


ONT Maintenance and Query
1- Query information about all ONTs connected to GPON port 0/8/0.
huawei(config-if-gpon-0/8)#display ont info
{ portid<0,3> }:0
{ ontid<0,63>|all<K> }:all
---------------------------------------------------------
Subrack/Slot/Port ONT SN Control flag Running flag Configuration status Matching status DBA
Mode ----------------------------------------------------------
0/8/0 1 323031312E396A41 Activated Offline Initial Matching SR
0/8/0 2 323031319C46B841 Activated Online Normal Match SR
0/8/0 3 485754438BC99302 Activated online Failed Matching SR
0/8/0 30 3230313192E95441 Activated Online Normal Mismatch SR
--------------------------------------------------------
2- Query the actual capabilities of an online ONT connected to GPON

port 0/8/0 Number of GEM ports: 32
Whether to support IP configuration: Supported
Number of traffic controllers: -
Number of T-CONTs: 7
Flow control type: Priority queue
Powering off the optical module: Not supported
---------------------------------
Number of PQs of T-CONT 0:3
Number of PQs of T-CONT 1:4
---------------------------------

• 3- Query the ONT configuration capability of GPON port 0/8/0.
huawei(config-if-gpon-0/8)#display ont config-capability 0 1
-------------------------
Port number: 0
ONT ID: 1
Management mode: OMCI
Number of POTS ports: 2
Number of Ethernet ports: 4
TDM port type: E1
TDM service type: TDMoGem
Number of TDM ports: 0
Number of MOCA ports: 0
Number of user-side CATV ports: 0
Number of GEM ports: 3
IP configuration: -
Mapping mode: VLAN
Number of T-CONTs: 4
Flow control type: PQ
--------------------------

4- Query the ONT version information.
huawei(config-if-gpon-0/8)#display ont version 0 1
--------------------------------------------------
Subrack/slot/port: 0/8/0
ONT ID: 1
Vendor ID: HWTC
ONT version: H821GPFA VER B
Product ID: 101
Device ID: SmartAX MA5620G
Active software version: V8R305 C02B063
Standby software version:
--------------------------------------------------
5- Query the optical power of the PON port of an ONT.

huawei(config-if-gpon-0/8)# display ont port attribute 0 3 eth
---------------------------------------------------------------
ONT No. Port No. Port Type Negotiation Mode Rate (Mbps) Duplex Port
switch Flow control switch Native Vlan Priority
--------------------------------------------------------------
3 1 ETH auto-negotiation auto-negotiation auto-negotiation enable
disable 1 0

Deleting an ONT
• Process for deleting an ONT
• If no service is configured, you can directly delete an ONT.
• If services are configured, you need to delete the services in the reverse order of the
service configuration before deleting the ONT.
huawei(config-if-gpon-0/8)#ont delete

Summary
• The following profiles need to be associated with an ONT:

• DBA profile
• Configures the upstream traffic parameters of a PON port. Each ONT needs to be configured with a
DBA profile.
• Line profile
• Configures the binding between T-CONTs and DBA profiles, GEM port IDs, service mapping mode
(VLAN or 802.1P), service types (Ethernet or TDM), QoS mode (PQ or CAR), and so on. Each ONT
needs to be configured with a line profile.
• Service profile
• Configures the types and IDs of ONT ports, and the mapping between port IDs and VLANs.
• Referenced when the management mode is set to OMCI for an ONT to be added.
• SNMP profile
• When the upper-layer network manages devices through an NMS server, you need to set SNMP
parameters, including the SNMP version, community name, and destination IP address.
• Referenced when the management mode is set to SNMP for an ONT to be added.

Thank You

ONT Configuration and Maintenance: Digital Egypt Youth Training Program

Uploaded by

Copyright:

Available Formats

ONT Configuration and Maintenance: Digital Egypt Youth Training Program

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ONT Configuration and Maintenance: Digital Egypt Youth Training Program

Uploaded by

Copyright:

Available Formats

ONT Configuration and Maintenance

Digital Egypt Youth Training Program

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

Terminal Profile Types

Process of Adding an ONT

Example for Adding Various ONTs

ONT Maintenance and Query

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

• SNMP: FTTB/C series

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

• DBA-profile add command is used to add a DBA profile.

huawei(config)#dba-profile add profile-id

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

huawei(config)#ont-lineprofile gpon profile-id

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

• Set the ONT port VLAN

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

• Commit the configurations.

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

huawei(config)# display ont-srvprofile gpon profile-id 88

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

Add an ONT and bind it to An FTTH ONT requires both a line

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

 Enable the function of

Manually add the SN of the

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

• Query the discovered ONT.

Note: The entered SN must belong to an automatically discovered ONT.

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

huawei(config-if-gpon-0/8)#display ont info 0 all

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

Device Type HG8247

OLT PON port 0/8/0

Management mode OMCI

ont-lineprofile ID 91, name hg8247

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

IP HOST Type 1; fixed

• 2-Configure an ONT service profile.

huawei(config)#ont-srvprofile gpon profile-id 91 profile-name hg850

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

• Configure a DBA profile for the Internet access service.

• Configure a DBA profile for the video service.

huawei(config)#dba-profile add profile-id 23 profile-name ftth_iptv

National Telecommunication Institute ‫المعهد القومي لالتصاالت‬

3- Bind a T-CONT to a DBA profile.