Machinist 1 YV2 TP

Download as pdf or txt
Download as pdf or txt
You are on page 1of 130

MACHINIST

NSQF LEVEL - 5

1st Year (Volume - II of II)

TRADE PRACTICAL

SECTOR: Capital Goods and Manufacturing

DIRECTORATE GENERAL OF TRAINING


MINISTRY OF SKILL DEVELOPMENT & ENTREPRENEURSHIP
GOVERNMENT OF INDIA

NATIONAL INSTRUCTIONAL
MEDIA INSTITUTE, CHENNAI
Post Box No. 3142, CTI Campus, Guindy, Chennai - 600 032

(i)
Sector : Capital Goods and Manufacturing
Duration : 2 Years
Trade : Machinist - 1st year (Volume II of II) Trade practical - NSQF (Level -5)

Developed & Published by

National Instructional Media Institute


Post Box No.3142
Guindy, Chennai - 600032
INDIA
Email: chennai-nimi@nic.in
Website: www.nimi.gov.in

Printed by
National Instructional Media Institute
Chennai - 600032

First Edition : March: 2020 Copies : 500

Rs. 145/-

(ii)
FOREWORD

The Government of India has set an ambitious target of imparting skills to 30 crores people, one out of every
four Indians, by 2020 to help them secure jobs as part of the National Skills Development Policy. Industrial
Training Institutes (ITIs) play a vital role in this process especially in terms of providing skilled manpower.
Keeping this in mind, and for providing the current industry relevant skill training to Trainees, ITI syllabus
has been recently updated with the help of Mentor Councils comprising various stakeholder's viz. Industries,
Entrepreneurs, Academicians and representatives from ITIs.

The National Instructional Media Institute (NIMI), Chennai, an autonomous body under Ministry of Skill
Development & Entrepreneurship is entrusted with developing producing and disseminating Instructional
Media Packages (IMPs) required for ITIs and other related institutions.

The institute has now come up with instructional material to suit the revised curriculum for Machinist
1st Year (Volume - II of II) Trade Practical NSQF Level - 5 in Capital Goods and Manufacturing
Sector under yearly Pattern required for ITIs and related institutions imparting skill development. The NSQF
Level - 5 Trade Practical will help the trainees to get an international equivalency standard where their skill
proficiency and competency will be duly recognized across the globe and this will also increase the scope
of recognition of prior learning. NSQF Level - 5 trainees will also get the opportunities to promote lifelong
learning and skill development. I have no doubt that with NSQF Level - 5 the trainers and trainees of ITIs,
and all stakeholders will derive maximum benefits from these IMPs and that NIMI's effort will go a long way
in improving the quality of Vocational training in the country.

The Executive Director & Staff of NIMI and members of Media Development Committee deserve appreciation
for their contribution in bringing out this publication.

Jai Hind

Director General
Directorate General of Training
Ministry of Skill Development & Entrepreneurship,
Government of India.

New Delhi - 110 001

(iii)
PREFACE

The National Instructional Media Institute (NIMI) was established in 1986 at Chennai by then Directorate
General of Employment and Training (D.G.E & T), Ministry of Labour and Employment, (now under Ministry
of Skill Development and Entrepreneurship) Government of India, with technical assistance from the Govt.
of the Federal Republic of Germany. The prime objective of this institute is to develop and provide instructional
materials for various trades as per the prescribed syllabi under the Craftsman and Apprenticeship Training
Schemes.

The instructional materials are created keeping in mind, the main objective of Vocational Training under
NCVT/NAC in India, which is to help an individual to master skills to do a job. The instructional materials are
generated in the form of Instructional Media Packages (IMPs). An IMP consists of Theory book, Practical
book, Test and Assignment book, Instructor Guide, Audio Visual Aid (Wall charts and Transparencies) and
other support materials.

The trade practical book consists of series of exercises to be completed by the trainees in the workshop.
These exercises are designed to ensure that all the skills in the prescribed syllabus are covered. The trade
practical book provides related theoretical knowledge required to enable the trainee to do a job. The test and
assignments will enable the instructor to give assignments for the evaluation of the performance of a trainee.
The wall charts and transparencies are unique, as they not only help the instructor to effectively present a
topic but also help him to assess the trainee's understanding. The instructor guide enables the instructor to
plan his schedule of instruction, plan the raw material requirements, day to day lessons and demonstrations.

In order to perform the skills in a productive manner instructional videos are embedded in QR code of the
exercise in this instructional material so as to integrate the skill learning with the procedural practical steps
given in the exercise. The instructional videos will improve the quality of standard on practical training and
will motivate the trainees to focus and perform the skill seamlessly.

IMPs also deals with the complex skills required to be developed for effective team work. Necessary care
has also been taken to include important skill areas of allied trades as prescribed in the syllabus.

The availability of a complete Instructional Media Package in an institute helps both the trainer and
management to impart effective training.

The IMPs are the outcome of collective efforts of the staff members of NIMI and the members of the Media
Development Committees specially drawn from Public and Private sector industries, various training institutes
under the Directorate General of Training (DGT), Government and Private ITIs.

NIMI would like to take this opportunity to convey sincere thanks to the Directors of Employment & Training
of various State Governments, Training Departments of Industries both in the Public and Private sectors,
Officers of DGT and DGT field institutes, proof readers, individual media developers and coordinators, but for
whose active support NIMI would not have been able to bring out this materials.

R. P. DHINGRA
Chennai - 600 032 EXECUTIVE DIRECTOR

(iv)
ACKNOWLEDGEMENT

National Instructional Media Institute (NIMI) sincerely acknowledges with thanks for the co-operation and
contribution extended by the following Media Developers and their sponsoring organisations to bring out this
Instructional Material (Trade Practical) for the trade of Machinist 1st Year (Volume - II of II) NSQF Level - 5
under Capital Goods and Manufacturing Sector for ITIs.

MEDIA DEVELOPMENT COMMITTEE MEMBERS

Shri. N. Manoharan - Asst. Training Officer,


Govt.I.T.I. Chengalpattu.

Shri. R. Kumaresan - Asst. Training Officer,


Govt.I.T.I. North chennai.

Shri. V. Alagaiah - ATO, Govt ITI,


Ambattur, Chennai - 98.

Shri. G. Loganathan - Govt ITI,


Ambattur, Chennai - 98.

Shri. M. Sampath - Training Officer NSTI (Retd),


NIMI, Chennai - 32.

Shri. T. Janakiraman - Assistant Director (Retd),


Govt RIC (N),
NIMI, Chennai - 32.

Shri. R. Kannan - DGM SIDCO (Retd),


NIMI, Chennai - 32.

NIMI CO - ORDINATORS

Shri. Nirmalya Nath - Deputy Director of Training


NIMI, Chennai - 32

Shri. V. Gopalakrishnan - Assistant Manager,


NIMI, Chennai - 32

NIMI records its appreciation for the Data Entry, CAD, DTP operators for their excellent and devoted services in
the process of development of this Instructional Material.

NIMI also acknowledges with thanks the invaluable efforts rendered by all other NIMI staff who have contributed
towards the development of this Instructional Material.

NIMI is also grateful to everyone who has directly or indirectly helped in developing this Instructional Material.

(v)
INTRODUCTION
TRADE PRACTICAL
The trade practical manual is intended to be used in practical workshop. It consists of a series of practical
exercises to be completed by the trainees during the 1st Year (Volume - II of II) of Machinist Trade supplemented
and supported by instructions / informations to assist in performing the exercises. These exercises are
designed to ensure that all the skills in compliance with NSQF LEVEL - 5 syllabus are covered.

The manual is divided into four modules. The distribution of time for the practical in the four modules are given
below:

Module 1 - Slotting
Module 2 - Milling
Module 3 - Advanced Turning
Module 4 - Grinding

The skill training in the shop floor is planned through a series of practical exercises centered around some
practical project. However, there are few instances where the individual exercise does not form a part of project.

While developing the practical manual, a sincere effort was made to prepare each exercise which will be easy
to understand and carry out even by below average trainee. However the development team accept that there is
a scope for further improvement. NIMI looks forward to the suggestions from the experienced training faculty for
improving the manual.

TRADE THEORY

The manual of trade theory consists of theoretical information for the 1st Year (Volume - II of II) of the Machinist
Trade. The contents are sequenced according to the practical exercise contained in NSQF LEVEL - 5 syllabus
on Trade Practical. Attempt has been made to relate the theoretical aspects with the skill covered in each
exercise to the extent possible. This correlation is maintained to help the trainees to develop the perceptional
capabilities for performing the skills.

The trade theory has to be taught and learnt along with the corresponding exercise contained in the manual
on trade practical. The indications about the corresponding practical exercises are given in every sheet of this
manual.

It will be preferable to teach/learn trade theory connected to each exercise at least one class before performing
the related skills in the shop floor. The trade theory is to be treated as an integrated part of each exercise.

The material is not for the purpose of self-learning and should be considered as supplementary to class room
instruction.

(vi)
CONTENTS

Exercise No. Title of the Exercise Learning Page No.


Outcome
Module 1: Slotting
2.1.61 Identification of slotting machine parts & its construction, use of
rotary table 1
2.1.62 Practice on slotting key ways on pulley with accuracy ± 0.04mm 1 2

2.1.63 Slotting a double -ended spanner with accuracy ± 0.1mm 6


2.1.64 Cutting sprocket teeth on slotting machine with accuracy ± 0.04mm 8
2.1.65 Cutting internal spline on slotting machine with accuracy ± 0.04mm 9

Module 2: Milling
2.2.66 Identification of milling machine 10
2.2.67 Demonstrate working principle of milling machine 11
2.2.68 Set vice & job on the table of milling machine 12
2.2.69 Set arbor on the spindle of milling machine 14
2.2.70 Set the cutter on arbor 15
2.2.71 Safety points to be observed while working on a milling machine 17
2.2.72 Demonstrate up milling and down milling process 18
2.2.73 Sequence of milling six faces of a solid block 20
2.2.74 Check the accuracy with the help of try square and vernier height 2
gauge 22
2.2.75 Perform step milling using side and face cutter checking with depth
micrometer 23
2.2.76 Perform slot milling using side and face cutter 26
2.2.77 Make ‘V’ block using horizontal milling machine with accuracy
± 0.02mm 29
2.2.78 Make concave surfaces with an accuracy ± 0.02mm 35
2.2.79 Make convex surfaces with an accuracy ± 0.02mm 37
2.2.80 Straddle milling operation with an accuracy ± 0.02mm 38
2.2.81 Gang milling operation with an accuracy ± 0.02mm 41
2.2.82 Make dovetail fitting (male & female) on milling machine with an
accuracy ± 0.02mm 43
2.2.83 Make T-slot fitting (male & female) on milling machine with an
accuracy ± 0.02mm 47
2.2.84 Demonstrate indexing head 50
2.2.85 Set and align indexing head with reference to job on milling machine 51
2.2.86 Make square job by direct/simple indexing method with an
accuracy ± 0.02mm 52
2.2.87 Make hexagonal job by simple indexing method with an
accuracy ± 0.02mm 56

(vii)
Exercise No. Title of the Exercise Learning Page No.
Outcome

Module 3: Advanced Turning

2.3.88 Checking of alignment of lathe centres and their adjustments 57


2.3.89 Turning practice - between centres on mandrel (gear blank) with
an accuracy ± 30 minutes 58
2.3.90 Taper turning by swivelling the cross - slide 60
2.3.91 Make square thread (external) on a lathe with an accuracy ± 0.02mm 64
2.3.92 Make square thread (internal) on lathe with an accuracy ± 0.02mm 67
2.3.93 Check with thread gauge - Grinding of tool and setting in correct 3
position 68
2.3.94 Fitting of male and female square threaded components 68
2.3.95 Make multi-start ‘V’ thread on lathe with screw pitch gauge 69
2.3.96 Perform eccentric turning with an accuracy ± 0.02mm 71

Module 4: Grinding

2.4.97 Identification of different types of grinding machines 74


2.4.98 Wheel balancing & turning 76
2.4.99 Dressing of grinding wheel 78
2.4.100 Grinding of block (six sides) by surface grinding machine with
an accuracy of ± 0.01mm 80
2.4.101 Grinding of step block by surface grinding machine with
an accuracy ± 0.01mm 84
2.4.102 Grinding of slot block surface grinding machine with an accuracy
of ±0.01mm 86
2.4.103 Set and perform angular grinding using universal vice/sine vice to
standard angle 89
2.4.104 Make slide fit with an accuracy ± 0.01mm (Male & Female) 91
2.4.105 Perform form grinding 4 94
2.4.106 Make dovetail fitting with an accuracy 0.01mm (Male & Female) 95
2.4.107 External parallel cylindrical grinding (Both holding in chuck/collet and
in-between centres 97
2.4.108 Plunge grinding 103
2.4.109 Perform straight bore grinding 104
2.4.110 Perform step bore grinding 107
2.4.111 Internal taper bore grinding 110
2.4.112 Make male female fitting with an accuracy of ± 0.01mm 111
2.4.113 External step cylindrical grinding with an accuracy of ± 0.01mm 113
2.4.114 External taper cylindrical grinding with an accuracy of ± 0.01mm 115

(viii)
LEARNING OUTCOME

On completion of this book you shall be able to


SI.No. Learning Outcome Ref. Exercise No.

1 Set the different machining parameters and cutting tool


to prepare job by performing different slotting operation.
(Different machining parameters - feed, speed and depth
of cut. Different slotting operations concave & convex
surface, internal key ways, profiling, making internal sprocket
with an accuracy of +/- 0.04mm) 2.1.61 to 2.1.65
2 Set the different machining parameters and cutters to prepare
job by performing different milling operation and indexing.
(Different machining parameters - feed,speed and depth of cut.
Different milling operations - plain, face angular, form, gang,
straddle milling) 2.2.66 to 2.2.87
3 Set the different machining parameters to produce square &
“V: threaded components applying method / technique and
test for proper assembly of the components. 2.3.88 to 2.3.96
4 Produce components of high accuracy by different operations
using grinding (Different operations - surface grinding,
cylindrical grinding with an accuracy of +/- 0.01mm) 2.4.97 to 2.4.114
SYLLABUS FOR MACHINIST
1st Year (Volume - II of II) - 06 Months
Duration. Reference Learning Professional Skills (Trade Professional Knowledge
Outcome Practical) with indicative hours (Trade Theory)
Professional Set the different 61.Identification of slotting machine Slotter – Classification, principle,
Skill 100 Hrs; machining parts & its construction, use of construction, Safety precaution.
Professional parameters and rotary table. (10 hrs)
Knowledge cutting tool to Introduction and their indexing process
28 Hrs. prepare job by 62. Practice on slotting key ways on a Slotter by its Rotary table
performing different on pulley with accuracy +/- 0.04 graduations.
slotting operation. mm (15 hrs)
Driving mechanisms, quick return
[Different machining motion and speed ratio.
parameters – feed,
speed and depth of Safety points to be observed while
cut. Different slotting working on a Slotter. (07 hrs.)
operations – concave
& convex surface,
internal key ways,
profiling,
making internal
sprocket with an
accuracy of +/- 0.04
mm]
63. Slotting a double ended Job holding devices-vice, clamps, V-
spanner with accuracy +/- 0.1 block, parallel block etc.
mm. (25 hrs) Slotting tools- types, tool angles. ( 07
hrs)
(ix)
64. Cutting sprocket teeth on Use of tool with holder for internal operations.
slotting machine with Precautions to be observed during slotting
accuracy +/- 0.04 mm. (25 hrs) internal operations.
Use of circular marks on the table for slotting
curves.
Chain, Sprocket and their applications. ( 07 hrs)
65. Cutting internal spline on Spline – types and uses.
slotting machine with accuracy
+/-0.04 mm. (25 hrs) Coolant & lubricant –

Introduction, types, properties, application &


applying methods. ( 07 hrs)

Professional Set the different 66.Identification of milling machine Milling Machine: Introduction, types,parts,
Skill150 machining (02 hrs) construction and specification.
Hrs.; parameters and 67.Demonstrate working principle Driving and feed mechanism of Milling Machine.
Professional cutters to prepare of Milling Machine. (04 hrs) ( 06 hrs)
Knowledge job by performing
42 Hrs. different milling 68. Set vice & job on the table of
operation and Milling Machine. (05 hrs)
indexing. [Different 69. Set arbor on the spindle of
machining milling machine. (08 hrs)
parameters – feed,
speed and depth of 70. Set the cutter on arbour. (04 hrs)
cut. Different 71.Safety points to be observed
milling operations while working on a milling
– plain, face, machine. (02 hrs)
angular, form,
gang, straddle
milling]
72.Demonstrate Up Milling and Different types of milling cutters & their use.
Down Milling Process.(05hrs) Cutter nomenclature. (06 hrs)
73.Sequence of milling six faces of
a solid block. (08 hrs)
74.Check the accuracy with the
help of try-square and vernier
height gauge. (02hrs)
75. Perform Step milling using side
and face cutter checking with
depth micrometer. (05hrs)
76.Perform slot milling using side
and face cutter. (05hrs)
77. Make “V” Block using Different milling operations - plain, face,
Horizontal Milling Machine with angular, form, slot, gang and straddle milling
accuracy +/- 0.02 mm. (20 hrs) etc. Up and down milling.(06 hrs)
78. Make concave surfaces with Different types of milling attachments and their
an accuracy +/-0.02 mm. (04 uses. (06 hrs)
hrs)
79.Make convex surfaces with an
accuracy +/-0.02 mm. (04 hrs)
80.Straddle milling operation with
an accuracy +/-0.02 mm.
(07 hrs)
81.Gang milling operation with an
accuracy +/-0.02 mm. (8 hrs)
(x)
82. Make Dovetail fitting (male & Jigs and Fixtures–
female) on Milling Machine with Introduction, principle, types, use, advantages
an accuracy +/-0.02 mm.(18 & disadvantages. ( 06 hrs)
hrs)
83.Make T-Slot fitting (male & Properties of metals general idea of physical,
female) on Milling Machine with mechanical properties of metals, colour, weight,
an accuracy +/-0.02 mm.(25 hardness toughness, malleability, ductility their
hrs) effect on machinability.
Heat Treatment – Introduction, necessity, types,
Purposes, different methods of Heat Treatment.
Heat Treatment of Plain Carbon Steel. (06 hrs)
84. Demonstrate indexing head. (05 Indexing-introduction & types. Indexing head-
hrs) types &constructional details, function of
indexing plates and the sector arms.
85.Set and align indexing head with
reference to job on milling Calculation for various types of indexing. (06
machine.(05 hrs) hrs)
86.Make square job by direct/
simple indexing method with an
ccuracy +/-0.02 mm. (06 hrs)
87.Make hexagonal job by simple
indexing method with an
accuracy +/-0.02 mm. (09 hrs)
Professional Set the different 88. Checking of alignment of lathe Turning of taper by taper turning attachment -
Skill 75 Hrs.; machining centres and their adjustments. advantages and disadvantages, taper
Professional parameters to (03 hrs) calculations.
Knowledge produce square &
89.Turning practice-between Mandrel, Lathe centres, Lathe dog, catch plate/
21 Hrs. “V threaded
centres on mandrel (gear blank) Driving plate, Face plate, Rests, their types &
components
with an accuracy +/-30 uses. ( 07 hrs)
applying method/
minute.(07 hrs)
technique and
test for proper 90.Taper turning by swiveling the
assembly of the cross slide.
components.
91.Make square thread (external) Terms relating screw thread major/minor
on a lathe with an accuracy +/- diameter, pitch and lead of the screw, depth of
0.02 mm. (12 hrs) thread. Simple gear train and compound gear
92.Make square thread (internal) on train change gears for fractional pitches.
a lathe with an accuracy +/-0.02 Square thread and its form and calculation of
mm. (15 hrs) depth, core dia, pitch dia.
93.Check with thread gauge –
grinding of tool & setting in Difference between single and multistart threads-
correct position. (04 hrs) their uses, merits and demerits. (14 hrs)
94.Fitting of male & Female Square
threaded components. (02 hrs)
95. Make multi-start V thread on
lathe with Screw Pitch
gauge.(10 hrs)
96. Perform eccentric turning with
an accuracy +/-0.02mm.(07 hrs)
Professional P r o d u c e 97. Identification of different types Grinding –
Skill 125 components of of grinding machine. (02 hrs)
Hrs.; high accuracy by 98.Wheel balancing & truing.(06 Introduction, grinding wheel- abrasive, types,
Professional d i f f e r e n t bond, grade, grid, structure, standard marking
hrs)
Knowledge operations using 99.Dressing of grinding wheel. system of grinding wheel, selection of the
35 Hrs. g r i n d i n g . grinding wheel. ( 06 hrs)
(02 hrs)
(xi)
[ D i f f e r e n t 100.Grinding of block (six sides) by Dressing, types of dresser.
operations – surface grinding machine with an
Glazing and Loading of wheels – its causes
surface grinding, accuracy of +/- 0.01 mm. (10 hrs)
and remedies.
c y l i n d r i c a l 101.Grinding of step block by
grinding with an surface grinding machine with an Roughness values and their symbols.
accuracy of+/- accuracy of +/-0.01 mm.(15 hrs.) Explain the importance and necessity of
0.01 mm] quality. ( 06 hrs)
102.Grinding of slot block by
surface grinding machine with an
accuracy of +/- 0.01 mm. (10 hrs)
103.Set and perform angular Surface Grinder –
grinding using universal vice/ sign Types, Parts, construction, use, methods of
vice to standard angle. surface grinding, specification & safety.
(08 hrs)
104.Make slide fit with an accuracy
± 0.01mm (male female) (05hrs)
105.Perform form grinding (05 hrs)
106.Make dovetail fitting with an
accuracy ± 0.01mm (male &
female) (8 hrs)
Cylindrical grinding: Cylindrical grinder:
107.External Parallel cylindrical Introduction, parts, construction, types,
grinding (Both holding in chuck/ specification, safety, different methods of
collet and in between centers. cylindrical grinding. ( 06 hrs)
(10hrs)
108. Plunge grinding (8hrs)
109.Perform straight bore grinding Cutting speed, feed, depth of cut, machining
(05hrs) time calculation. ( 06 hrs)
110.Perform step bore grinding
(05hrs)
111.Internal taper bore grinding
(05hrs)
112.Make male female fitting with an
accuracy of +/- 0.01 mm (8 hrs)

113.External step cylindrical Wet grinding and dry grinding, various types
grinding with an accuracy of +/- of grinding wheels and their application,
0.01 mm (10hrs) grinding defects and remedies. ( 05 hrs)
114. External taper Cylindrical
grinding with an accuracy of +/-
0.01 mm. (08 hrs)

In-plant training/ Project work


Broad area:
a) Drill extension socket
b) V-belt pulley
c) Tail Stock Centre (MT – 3)
d) Taper ring gauge
e) Taper plug gauge. (Morse taper

(xii)
Capital Goods & Manufacturing Exercise 2.1.61
Machinist - Slotting
Identification of slotting machine parts & its construction, use of rotary table
Objective: At the end of this exercise you shall be able to
• identify and write the name of parts of the slotting machine
• know the construction of slotting machine
• know the use of rotary table.

Job Sequence
Instructor shall brief the name of the parts and Table 1
construction of slotting machine, and the use
Sl.No Name of the parts Uses
of rotary table. Ask the trainees to record the
part names in the table 1 1
2
• Trainees will note down all the part’s name in the table
1. 3

• Practice on manual movement of rotary table in different 4


position. 5
• Practice on starting and stopping of the slotting 6
machine. 7
• Get it checked by your instructor 8

1
Capital Goods & Manufacturing Exercise 2.1.62
Machinist - Slotting
Practice on slotting key ways on pulley with accuracy ± 0.04mm
Objectives: At the end of this exercise you shall be able to
• face and centre drill the pulley
• mark the keyway
• hold the pulley on slotting machine
• set the tool on the machine
• slot the keyway as per dimension.

2
Job Sequence
• Check the raw material • Turn the job to 92mm diameter
• Hold the job on 4 jaw chuck with 5 mm over hang • Remove the job
• Set the facing tool and face one end of the job. • Check the outside, inside and the thickness of the
pulley.
• Fix the drill chuck in the tail stock spindle and fix the
centre drill • Mark the centre lines and keyway.
• Centre drill the work • Clamp the keyway (slotting) tool.
• Drill pilot holes starting from 8mm up to 25 mm • Clamp the pulley approximately at the centre of the
slotting table and align it.
• Set the boring tool and bore hole 27mm
• Set the length and position of the stroke
• Reverse and refix the job and true it
• Slot the keyways 6x3mm to the given accuracy.
• Face the other end to maintain 20 mm width
• Deburr the job.
• Remove the job and fix in mandrel
• Check the dimensions using a vernier caliper.

Skill Sequence
Aligning slotting tool for slotting
Objective: This shall help you to
• set the slotting tool in the tool box of the slotting machine and align the slotting tool.

Select the required tool. Tighten the bolts fully.


Clean the tool box. For tool bits, use a tool-holder and follow the steps stated
above.
Insert the tool in the tool clamps till it touches the tool
stopper.
Butt the tool to one side of the clamp.
Use packing pieces between the clamp and the tool, if
necessary, to align the tool in line with the locking bolt.
Align the tool in vertical position to eye judgment and finger
tighten the tool by locking bolts.
Project the tool sufficiently to ensure that the tool box is
not fouling with the top of the work.
Using a square head/try square, set the shank
perpendicular to the face of the rotary table. (Fig.1)
Use soft hammer for tapping the tool while aligning with
the try square.

Setting the length of stroke and position of ram


Objectives: This shall help you to
• set the length of stroke
• set the position of the ram.

Ensure that the machines is switched off. This is ensure complete removal of material over the whole
length of the job surface, and
Bring the ram to its extreme upward position to read the
existing length of stroke, by rotating the fly wheel by hand. To provide sufficient clearance and time to complete the
(Fig.1) feeding of the tool before the next cut is taken on the
down stroke.
Determining the length of stroke (Figs.2&3)
Length of stroke = Length of job+25 to 30mm clearance.
The length of stroke should be 25 to 30mm more than the
height of the surface to be machined.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.1.62 3


Positioning the RAM (Fig.4)
Bring the ram to its lowest position by rotating the fly
wheel by hand to know the position of the tool at its lowest
point.
Loosen the ram lock-nuts.
Rotate the ram positioning screw shaft in clockwise or
anticlockwise direction till the tool reaches a position 5mm
below the job bottom surface.
Tighten the ram lock-nuts.
Rotate the flywheel by hand to ensure the correct setting
of the length of stroke and position of the ram.

Eg. Length of stroke = 70+30=100mm.(Fig.2)


Loosen the crank pin lock-nut which is at the end of the
connecting link.
Rotate the stroke setting screw shaft using a box spanner,
in clockwise direction till the pointer indicates the required
stroke length (100mm). (Fig.3)
Tighten the crank pin lock - nut.

Slotting an internal keyway


Objectives: This shall help you to
• lay out the job for slotting an internal keyway
• slot an internal keyway.
Mark the centre line, width and depth of the keyway as Mount the work on the parallels, and by eyesight, align
per the drawing. the bore of the job to the centre bore of the table.
Select parallel of suitable thickness and place on the Clamp the job using clamps, bolts and nuts.
table. Select and mount the keyway roughing tool.

4 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.1.62


Ensure that the width of the tool edge is less than the
width of the keyway.
Attach a sticky pin pointer to the tool.
Align the centre line of the job to the pointer by using
longitudinal, cross and rotary feeds. (Fig 1)

Give a depth of cut about 1 mm and rough-machine the


keyway leaving 0.5 mm for the finish cut.
Use the cross-feed for slotting the width and longitudinal
feed for depth. (Fig 3)
Lock the rotary feed.
Set and align the keyway finishing tool in the holder.
Set the tool edge parallel to the depth line of the keyway.
Slot and finish the keyway to the given dimensions.
Bring the tool edge 0.5mm above the job surface by
rotating the fly wheel by hand . De-clamp the job.
Adjust the stroke length, position of the ram and the ram Check the dimensions of the keyway.
speed.
Ensure that the cutting point is 10 mm above the table
when the ram is at its lowest position.
Set the position of the job so that the tool lies at the
centre of the bore by eyesight by adjusting the longitudinal
and cross-feed. (Fig 2)

Switch on the machine.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.1.62 5


Capital Goods & Manufacturing Exercise 2.1.63
Machinist - Slotting
Slotting a double-ended spanner with accuracy ± 0.1mm
Objectives: At the end of this exercise you shall be able to
• mark and punch the outline of the job as per drawing with a template
• chain drill for removing excess material
• slot concave and convex faces to an accuracy of ±0.1mm
• slot rectangular opening to an accuracy of ±0.1mm
• slot rectangular opening to an accuracy of ±0.1mm.

Job Sequence
• Check the raw material for its size. • Drill the holes ø20 and ø18.
• Slot the edges B D E F to square with each other. • Align the holes with the rotary table axis and slot the
Provide enough material along the length and breadth internal radius. (Fig 2)
for further slotting. (Fig 1)

• Slot the shaded portion.


• Align the marking with the movement of the Table.
Slot side of the opening. Repeat the procedure for the
side opening.
• Check the width for 22 mm.
• Repeat the procedure for opening on the opposite side.
• Mark the job using a template.
• Check width for 20. (Fig 3)
• Mark the positions for holes.

6
• Align the marking with the movement of the table.
• Slot the taper profile at one side. Repeat the procedure
for the taper profile at the other side.
• Slot the round corners using a form tool. (Fig 5)

• Align the marking of the external profile with the axis


of the rotary table.
• Slot the external profile using circular feed. Repeat
the procedure for the external profile at the other end.
(Fig 4)
• Deburr the corners for smoothness. (Fig 6)
• Check the various dimensions of spanners using
different instruments.

• Saw the shaded portion keeping 1 mm allowance for


slotting.

Skill Sequence
Slotting irregular contour / profile
Objectives: This shall help you to
• lay out irregular contour/profile on the job
• slot the irregular contour/profile.

Lay out the job as per the drawing. (Fig 1)


Mount the job at the centre of the table using parallels,
clamps, T- bolts and nuts.

Ensure that the clamps and parallels are not fouling, while
slotting a particular curve.
Set and align the tool in the tool-holder.
Rough machine the contour leaving 0.5mm for the finish
cut, using longitudinal, cross and rotary feeds(Fig 2) Attach
a sticky pointer/pin on the tool edge.
True the contour to the pointer by using rotary, longitudinal
Machine the contour by taking finish cut, using rotary feed.
and cross feeds. (Fig 3)
Repeat for completing other contours.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.1.63 7


Capital Goods & Manufacturing Exercise 2.1.64
Machinist - Slotting
Cutting sprocket teeth on slotting machine with accuracy ± 0.04mm
Objectives: At the end of this exercise you shall be able to
• grind tool for sprocket teeth
• mount and align the job on a circular table using a special job holding device for the slotting sprocket (R)
• slot sprocket teeth.

Job Sequence
• Turn the job as per drawing. • Check the tool profile using the template prepared.

• Check the outside diameter, with the given data. • Indexing may be elebrated. (Pitch 18°)

• Provide step by step pricautions. Circumferce = 2r


• Using the template grind the form tool = 2x3.142 x 40.4
• Draw the root circle on the blank, to draw teeth.
253.71 253.71
• Drill the centre position of the job according to = 253.71 = 
Pitch 12.7
the drawing dimension.
= 20 Teeth
• This step may be elebrated.
• Cut the remaining teeth of the sprocket one by one.
• Set and align the tool with respect to the job/
rotary table. • Check all the teeth profiles using the template
• Slot the 1 tooth to full depth.
st prepared.

8
Capital Goods & Manufacturing Exercise 2.1.65
Machinist - Slotting
Cutting internal spline on slotting machine with accuracy ± 0.04mm
Objectives: At the end of this exercise you shall be able to
• grind tool for internal spline
• mount and align the job on a circuit table using job holding devices
• slot internal spline
• repeat the procedure for the remaining spline.

Job Sequence • Align the centre with respect to the rotary table using
a dial test indicator.
• Check the bore diameter ø28mm of the blank.
• Align the tool with respect to the job.
• Layout outside circle ø34mm and splines of width 7mm
on the face of the blank. • Slot internal spline to a width 7mm and depth 3mm.

• Hold the job on the rotary table using parallels, clamps • Check the dimensions of the spline.
and bolts. • Index the table through 60o and slot the next spline.

9
Capital Goods & Manufacturing Exercise 2.2.66
Machinist - Milling
Identification of milling machine
Objective: At the end of this exercise you shall be able to
• identify and record the type of milling machine
• identify the parts of milling machine
• record the parts name in table.

Job Sequence
Instructor shall show the horizontal and • Record the parts name in Table - 1 for horizontal
vertical milling machines. Brief the each part and Table 2 for vertical milling machine.
of milling machines, ask the trainees to till the
parts name in Table - 1 for horizontal milling Table 2- Vertical milling machine
machine and Table - 2 for vertical milling
Sl. No. Name of the parts
machine.
1
• Trainees to note down the part names of both milling
2
machines
Table 1- Horizontal milling machine 3
4
Sl. No. Name of the parts
5
1
6
2
3 • Get it checked by instructor.

4
5
6

10
Capital Goods & Manufacturing Exercise 2.2.67
Machinist - Milling
Demonstrate working principle of milling machine
Objectives: At the end of this exercise you shall be able to
• movement of the slides manual and automatic
• run the machine in different spindle speed
• put ON and OFF the machine.

Table 1
Job Sequence
Sl.No Name of the parts Type of movement
• Identifiy the machine parts.
1
• Move the slides manually
2
• Set the different spindle speed.
3
• Practice on mounting of different arbor. 4
• Practice on automatic feed and rapid movement. 5
6
7
8

11
Capital Goods & Manufacturing Exercise 2.2.68
Machinist - Milling
Set vice & job on the table of milling machine
Objectives: At the end of this exercise you shall be able to
• align a machine vice on the table of the milling machine
• fix the workpiece in machine vice.

Job Sequence
Clean the vice base and the machine table top, free from
dust for seating.
Place the vice at the middle of the table with maximum
support to avoid falling off of the vice. (Fig 1)
Position the ‘T’ bolts into the ‘T’ slot. (Fig 1) While shifting
the vice towards the slots ensure that there is 1mm to 2mm
clearance between the ‘T’ bolt and the vice slot to allow for
adjustment.

Position the dial indicator with the magnetic base firmly on


the reference surface (X). (Fig 3).

Tighten all the ‘T’ bolt nuts by hand.


Clamp the parallel block in the vice. (Fig 2) Set the vice
such that the jaws are at right angle to the direction of cut.

12
Engage the dial indicator stylus on one end of the parallel. Check the alignment after clamping, and adjust, if
(Fig 3) Ensure that the dial indicator and stand do not foul necessary.
anywhere.
Adjust the position of the dial pressure and set the reading Lubricate the vice screw and the slide ways.
to zero on one end of the parallel.
Place one of the larger surfaces of the workpiece on the
Move the table so that the dial indicator is at the other end parallel to prevent its downward movement while machine.
of the parallel. (Fig 4) observe the pointer movement.
Ensure that the workpiece is projecting the vice jaws by
If the pointer deviates from zero, adjust the vice by gentle about 3 to 5 mm more than the total depth of cut. This
tapping in the direction as needed. (Fig 4) Ensure that the avoids resetting of the job now and then also it prevents the
plunger is not lifted while tapping. vice jaws, tools and workpiece from damage.
Place a rod of diameter 6 to 15mm between the middle of
the unfinished side and the movable jaw. This gives line
contact between the job and prevents lifting off the workpiece.
(Fig 5).

Repeat the step until the dial indicator reads zero along the
Tighten the workpiece.
length.
Tighten the vice clamping nuts without disturbing the Tap the workpiece gently with a soft hammer for seating on
setting. the parallel. Ensure that the parallel block does not shake.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.68 13


Capital Goods & Manufacturing Exercise 2.2.69
Machinist - Milling
Set arbor on the spindle of milling machine
Objective: At the end of this exercise you shall be able to
• mount arbor on the machine spindle of milling machine.

Job Sequence
Set the lowest available spindle speed to avoid free rotation
of the spindle nose.
Ensure that the machine is switched off. Consult your
instructor.
Select the arbor with correct diameter and taper to suit
the machine spindle nose.
Clean the internal thread and taper portion of the arbor.
(Fig 1)

Tighten the draw - bar from the rear side of the spindle
and secure the arbor into machine by tightening the lock
- nut. (Fig 4)

Clean the spindle nose of the machine. (Fig 2)

Unscrew and remove the nut from the arbor end by rotating
it in the clockwise direction. (Fig 5)

For cleaning, use soft cloth free from dust, chips etc. to
avoid scratches on the surface.
Hold the arbor and ensure that the arbor notches fit on to
the nose of the tenon to get the drive. (Fig 3)
14
Capital Goods & Manufacturing Exercise 2.2.70
Machinist - Milling
Set the cutter on arbor
Objective: At the end of this exercise you shall be able to
• mount and position the cutter on milling machine arbor.

Job Sequence
Remove the spacers and bearing bushes and clean them.
(Fig 1)

Ensure that the key is placed into the keyway, and milling
cutter.
Slide the bearing bush on to the arbor. (Fig 4)

Insert enough spacers on to the arbor so that the last


spacer extends over the rear edge of the workpiece. This
will enable you to fix the cutter in the middle of the
workpiece for milling. (Fig 2)

Slide on more spacers until one or two threads on the


arbor screw are covered so that the spacers are pressed
while tightening.If not, the cutter may not be tightened
sufficiently.
Tighten the arbor nut by hand. (Fig 5)

Clean the side and face the cutter and the bore of the -
cutter.
Select the key to suit the cutter keyway.
Place the cutter on the arbor such that the direction of
rotation of the cutter is in the opposite direction of the job
feed for up-milling at the initial stage. Depending upon
the condition of the machine, down-milling may be
performed at a later stage of practice. (Fig 3)

15
Carefully slide the arbor support. (Fig 6) Tighten the arbor nut and switch on the machine and
check visually that the cutter runs true. (Fig 7)
The milling machine, like all machine tools,
should be cleaned after each work period. A
medium width paint brush may be used to
remove the accumulated chips.

Ensure that the bearing bush extends equally


on both sides of the arbor for uniform support.

16 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.70


Capital Goods & Manufacturing Exercise 2.2.71
Machinist - Milling
Safety points to be observed while working on a milling machine
Objective: At the end of this exercise you shall be able to
• adopt the safe procedures while working on milling machine.

Do not use this machine unless a instructor - Clean the cutter or workpiece while the machine is in
has instructed you in its safe use and still position.
operation and has given permission. - Do not use machine table as storage space for
• Safety glasses must be worn at all times in work areas. spanners, mallets and other tools. These tools may
fall down and injure the workmen when the machine
• Appropriate footwear with substantial uppers must be table is moving.
worn.
- While using cutting fluid or lubricant directly from the
• Rings and jewellery must not be worn machine, make sure that the flow pipe outlet is well
• Long and loose hair must be contained. clear of the milling cutter.

• Close fitting/protective clothing must be worn. - Do not fix a heavier job than recommended for the
mahine.
• Gloves must not be worn when using this machine
- Check the job for proper clamping.
- Use a cutter guard wherever possible.
- Use a piece of cloth for protection of the cutter and
- Do not take any measurement while the machine is in your hands when handling the milling cutter.
running condition i.e stop the machine first and then
take measurement. - Do not be distracted or talk to others while operating
the machine.
- Use proper feeds and depth of cuts avoid heavier
feeds and cuts. - Only remove chips using gentle air blasting or chip
brushess.
- Before taking any cut ensure that the job is properly
clamped. - Be aware of cutting tools.
- Never reach any where over around or near any rotating
cutters.

17
Capital Goods & Manufacturing Exercise 2.2.72
Machinist - Milling
Demonstrate up milling and down milling process
Objectives: At the end of this exercise you shall be able to
• set the cutter on the arbor and decide the direction of rotation
• set the job correctly on the vice
• mill the surface by up milling
• mill the surface by down milling.

Job Sequence
The two operating procedures are distinguished by the to the thickest part. (Fig 2) The cutting edge slides in the
directions in which the teeth of the cutter and the feed of material before it starts to cut. This scraping causes a
the workpiece move. good deal of heat and wear on the cutter. As the cutter
teeth emerge from the material, the accumulated cutting
TASK 1: Up-cut milling
forces are suddenly released.
The most commonly used method of feeding is to bring the
work against the direction of rotation of the cutter. (Fig.1)
This is otherwise known as convention milling. This is the
most commonly used method.

The cutter and workpiece suddenly spring apart, the


machine chatters, and the material surface is flawed by
ripples. The spindle for the milling is tensioned in the
direction of the feed. The forces involved are taken up by
In up-milling the removal of chip by each cutting edge the flank of the thread in contact.
starts at the thinnest part of the chip (a) and progresses

TASK 2: Down-cut milling


In down-milling or climb-milling the feed moves in the same
direction as the rotation of the cutter. (Fig 3)

Because in climb-milling the cutter is pulling the workpiece,


it should only be carried out on a machine having a
In this method, chip removal starts at the thickest part. ‘backlash eliminator’. This is because the backlash
The cutter cuts into the material straightway and does not eliminator takes up any clearance in the feed drive
slide. (Fig 4) As a result less heat is developed and there mechanism and prevents the cutter from being pulled
is less wear on the cutter. along.
In this method, the workpiece is pressed down on the work If down-milling is tried on a machine without a backlash
table by the cutting pressure and thus prevents the eliminator, the workpiece will move along in a series of
workpiece from lifting. (Fig.5) This is an advantage, jerks (Fig 6), resulting in very poor finish and even breakage
especially when milling long workpieces. of the cutter.
18
Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.72 19
Capital Goods & Manufacturing Exercise 2.2.73
Machinist - Milling
Sequence of milling six faces of a solid block
Objectives: At the end of this exercise you shall be able to
• set the workpiece on a horizontal milling machine
• mill six faces perpendicular to each other
• maintain the size of the workpiece.

Job Sequence
• Clamp the machine vice securely on the machine • Keep surface ‘A’ against the fixed jaw and surface
table and align jaw parallel to the coloumn. D on the parallel block.
• Fasten the cutter in the machine. • In the middle of the surface C, a round rod is kept
between the job and the movable jaw for line contact
• Set the required RPM
to avoid lifting of the job. This roller enables for
• Place surface ‘C’ on the parallel block, clamp the maintaining squareness of the surfaces A&B.
job. Ensure that the parallel block dose not move. (Fig 2)
• Mill surface ‘A’ flat. (Fig 1). • Mill surface ‘B’ at right angle to surface ‘A’. (Fig 2)

20
• Keep the surface ‘A’ on the parallel blocks and butt • Keep surface ‘C’ on the parallel blocks (Fig 5)
the surface B to the fixed jaw.
• Place a round rod in between movable jaw and surface
D.
• Mill surface C maintaining the size of 46mm (Fig 3).

• Set side and face milling cutter and mill the surface ‘E’
(Fig 6)
• Set the RPM for side and face cutter.

• Keep surface C on the parallel blocks.


• Set the work, projecting it atleast 10mm from the sides • Mill the ‘F’ side by the side and face cutter and maintain
of the vice. the size (Fig 7)
• Mill surface ‘D’ maintaining a size of 46 mm (Fig 4)

• Deburr the job and check all the dimensions.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.73 21


Capital Goods & Manufacturing Exercise 2.2.74
Machinist - Milling
Check the accuracy with the help of try square and vernier height gauge
Objectives: At the end of this exercise you shall be able to
• check the flatness with try square
• check the squareness with try square
• check the height with the vernier height gauge.

Job Sequence
TASK 1: Checking flatness with try square
During the initial stages of filing the evenness of the surface Checking sequareness
can be visually observed to a reasonable degree of
While checking for squareness, the large finished surface
perfection from the surface texture of diagonal filing.
is taken as a reference surface. (Fig 2)
To ensure perfection, the surface should be checked with
Ensure that the reference surface is finished perfectly
a straight edge. To do this, the blade of a try square can
before filing other surfaces.
serve as a straight edge.
Burrs, if any, should removed before checking with a try
Flatness should be checked in all directions so as to
square.
cover the entire surface. Light gap will indicate high and
low spots. (Fig 1)

TASK 2: Check the accuracy with the help of vernier height gauge

• Keep the job on the surface table


• Set the vernier height gauge on the surface table
• Zero set the instrument using the offset scribes
• Zero setting of the instrument is at a level above the
datum surface for using the straight scriber.
• Check the height of the job to a accuracy of ± 0.02mm.

22
Capital Goods & Manufacturing Exercise 2.2.75
Machinist - Milling
Perform step milling using side and face cutter checking with depth
micrometer
Objectives: At the end of this exercise you shall be able to
• lay out the job as per drawing with a vernier height gauge
• set the job in the machine vice for machining
• mount a side and face cutter on the arbor
• mill steps on the job
• check the dimensions of the steps using a depth micrometer.

Job Sequence
• Check the dimensions of the block. (Deburr, if • Set the r.p.m. of the cutter near to 50.
necessary) • Clamp the job in the machine vice to mill all the steps
• Mark the steps on the block (steps) as per the in one setting.
dimensions and punch witness marks. • Align the cutter and the job for milling the step.
• Align the machine vice with reference to the column • Mill the steps in sequence and check with a depth
using dial indicator. micro meter.
• Mount a Ø32 mm long arbor and a side and face Mill the relief groove before grinding for
milling cutter of Ø125x16x32mm bore for the grinding purpose.
horizontal milling machine.
• Drill relief hold Ø3 mm at the junction of steps.

23
Skill Sequence
Mill steps on plain milling machine
Objective: This shall help you to
• mill steps on plain milling machine.

Align and mount the plain machine vice on the machine


such that the vice jaws are parallel to the column.
Mark the job as per drawing and punch witness marks.
Hold the job in the machine vice.
Clamp the job in the machine vice such that all
the steps can be machined in one setting.
(Fig 1) If the job cannot be accommodated on
the plain milling machine, step mill on the
vertical milling machine.

Mount the long arbor and the side and face milling cutter.
Ensure that (D - S)/2 is 5 to 6 mm more than the maximum
depth to be machined.
D = diameter of the cutter
S = outside diameter of the spacers
The gap of 5 to 6 mm is provided to avoid fouling of the
spacers with the job while machining. (Fig 2)
Set the machine for up-milling.
Calculate and select suitable r.p.m. for the cutter.
Stick tissue paper (T) on the side face of the job. (Fig 3) Start the spindle.

Raise the vertical slide such that the upper surface of the Move the cross-slide slowly till the tissue paper is just
job is 10 to 15 mm above the cutter. displaced from its position.

Move the table and bring the tissue paper side of the job Stop the machine as soon as the tissue paper slips.
parallel to the side of the cutter with a gap of 5 to 6 mm. Lock the cross-slide.
(Fig 4)

24 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.75


Adjust the graduated scale to zero of the cross-slide. Rough mill the steps a,b,c in that order. (Fig 6)
This is the datum in one axis for milling the
steps horizontally.
Stick the tissue paper on the top surface of the job.
Clear the workpiece from the cutter and set the cutter
10-15 mm above the top surface of the job.
Start the machine.
Raise the workpiece slowly and manually till the job just
touches the cutting edges and the tissue paper slips away
by the rotation of the cutter. (Fig 5)

Leave 0.5 mm allowance of material on both the axes for


the final finish.
While machining observe for abnormal noise, vibration of
job or cutter and bad surface finish. If you are in doubt stop
the machine and check that the
- job is tightened firmly, without any shake
- cutter is tightened securely without play
- cutter teeth are not blunt.
Ensure defect-free machining condition, restart the machine
and complete the rough milling operation.
Clear the job from the cutter and deburr the job.
Stop the machine as soon as the tissue paper slips.
Measure the job and confirm that that 0.5 material is left
Adjust the graduated scale to zero of the vertical slide.
for final finishing.
This is the datum in another axis for milling the
Set the machine and complete the steps to the final
steps vertically.
dimension and finish to a smooth surface by automatic
Unlock the vertical slide. feed.
Clear the job from the cutter. A fine finish is achieved by relatively high
cutting speed and fine feed - check the
Take care that the datum, set for both the axes,
dimension after completion of each step -
is not disturbed.
consult the instructor.
Set the coolant nozzle towards the cutter.
Stop the machine and deburr the job.
Depending upon the condition of the machine,
Remove the job and measure for its size.
rough milling is possible by using a heavy
feed, with a depth of cut from 5 to 10 mm and Stop the machine before attempting to make
a low cutting speed. Rough milling is done to adjustments or measurements.
remove surplus material in the shortest time.
Consult the instructor when and if necessary.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.75 25


Capital Goods & Manufacturing Exercise 2.2.76
Machinist - Milling
Perform slot milling using side and face cutter
Objectives: At the end of this exercise you shall be able to
• set the job in the machine vice for machining
• align the job with respect to the cutter
• mill the slot to an accuracy of ± 0.04 mm
• check the width of the slot using a vernier caliper
• check the depth of the slot using a vernier depth gauge.

26
Job Sequence
• Check the dimensions of the block, 100 x 50 x 50mm.
• Machine the block to the dimension of 96 x 46 x 46mm.
• Mark the groove as per drawing and punch witness
marks.
• Hold the job on the machine vice using parallel blocks.
• Mount the side face milling cutter 100 x 12 x 27 mm
bore at the centre of the arbor and set the spindle speed
to 100 r.p.m.
• Align the workpiece with reference to the cutter.
• Mill the slot in the middle of the job giving a depth of cut
of 4 mm up to a depth of 21 mm. (Fig 1)

• Reset the job and mill a slot of 25 x 10 on the opposite


side. (Fig 4)
• Deburr and measure.

• Offset the job towards the column by 2.0 mm (Fig 2) and


mill the width to 14.0 mm (Fig 2). Offset the job away
from the column by 5 mm and mill the slot to 17 mm.
(Fig 3)
• Check the size of the slot.

Skill Sequence
Mill a slot by side and face milling cutter
Objective: This shall help you to
• mill a slot by a side and face milling cutter.

Deburr and clean the workpiece.


Mark the job as per drawing and punch witness marks on
the lines.
Mount the plain machine vice on the plain milling machine
such that the vice jaws are parallel to the column.
Select the cutter size.
The width of the cutter should be less than the width of the
slot required.
Calculate the diameter of the cutter approximately, using
the following thumb rule.
Select the nearest higher diameter available.
Dia. of cutter/2 = (depth of slot + bore dia./2 + 20) x 2.
Calculate the r.p.m. for the selected dia. of the side and
Mount the long arbor and the side and face milling cutter
face cutter.
on the machine.
Calculate the feed per minute of the longitudinal traverse.
Ensure that the cutter is mounted at the middle of the arbor
to facilitate the free traverse of the cross-slide. Set the r.p.m. and feed.
Clamp the job with its marked surface on the top, between Stick tissue paper to the reference sides of the workpiece
the vice jaws firmly. and set the datum for the cross and vertical slides.
Keep the job on the pair of parallels in such a way that the Set the cutter at the middle of the slot to (X+W/2) mm
top surface of the job is above the top surface of the jaws taking reference from the side datum (cross-slide).
by 4 to 5 mm. (Fig 1) (Fig 2) W is width of the slot.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.76 27


Set the depth of cut taking reference from the top surface
of the job.
Be sure that whenever the depth of cut is
taken, the cutter is away from the job.
Keep 0.4 to 0.5 mm on both the sides and depth of the slot
for final finish.
Lock the vertical and cross-slides. Adjust the coolant
nozzle point on the cutter.
Start the machine and the coolant pump.
Move the longitudinal slide manually towards the cutter
such that the workpiece comes in contact with the cutter
gently. Sudden contact may damage the workpiece and
the cutter may break.
Mill the depth at the middle of the slot leaving 0.4 to 0.5mm
for final finish. (Fig 3)

Move the cutter to the left to a distance of X + 0.5 mm and


mill the side of slot. (Fig 4)
Ensure that the datum is again set whenever
the cutter is changed or the job disturbed.

Move the cutter to the right to a distance of (X+W) =


0.5mm and mill the right side of the slot. (Fig 5)
Follow the above procedure and mill the slot to size.
(Fig 6)
Be sure the holding device is mounted solidly
Deburr the job. to the table and the work is held firmly. Spring
Check the slot for dimension. or vibration can cause thin cutters, like the
slitting saw, to jam and chatter.

28 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.76


Capital Goods & Manufacturing Exercise 2.2.77
Machinist - Milling
Make ‘V’ Block using horizontal milling machine with accuracy ±0.02mm
Objectives: At the end of this exercise you shall be able to
• mark and punch as per drawing
• set slitting saw cutter
• set 90° double angle milling cutter on arbor
• cut angular surface to an accuracy of ± 10 minutes
• check angle using vernier bevel protractor
• check dimensions using vernier caliper
• cut slots with an accuracy of ± 0.02mm.

29
Job Sequence
• Machine the block flat and square, to size
50+40+40mm (Fig 1)

• Mark and punch the job as per drawing (Fig 2)

• Cut slot (shaded portion)maintaining dimensions 15,10


and 5 mm on both sides (Fig 4) using 10mm width side
face cutter.
• Check the angular dimensions using vernier bevel
protractor.

• Set the slitting saw 4mm width


• Hold the job on machine vice
• Mill the slot maintaining dimensions 18,18 and 4mm.
(Fig 3)
• Machine angular surface using 45 double angle cutter
both the sides. • Check the dimensions with vernier caliper
• Remove the burrs

Skill Sequence
Mill narrow groove by using slitting saw
Objective: This shall help you to
• mill a narrow groove by using a slitting saw.
Mark the job as per drawing to mill a narrow groove. The thickness of the slitting saw sholud be equal to the
width of the groove.
Mount a plain machine vice on a plain milling machine
such that the jaws are parallel to the column. The diameter must be sufficiently large so that the desired
depth can be achieved.
Set a pair of parallel blocks in such a way that the top
surface of the job is 5 to 6 mm above the top surface of Check that the slitting saw is sharp and undamaged.
the jaws.This will help to measure the dimensions of the
A blunt or damages slitting saw may create excessive
slot from the sides using a vernier caliper.
vibration and may result in the breakage of the slitting
Clamp the workpiece in the machine vice. saw.
Select the slitting saw. Select the arbor having the same diameter as the bore of
the slitting saw.
30 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.77
Mount the long arbor on the plain milling machine.
Mount the slitting saw on the centre of the arbor.(Fig 1)

Do not insert the key between the arbor and


slitting saw, if the slitting saw is less than 4mm Ensure that the spindle is disengaged. This will
thick. ensure that the spindle will not rotate
accidentally.
The use of a key may result in the breakage of the slitting
saw if it gets jammed into the cut during cutting.
Lock the cross - slide.
Select the cutting speed, the feed for the slitting saw
Stick tissue paper on the top surface of the workpiece
considering the material the saw is made of .
and set the datum for the vertical slide.
Calculate the r.p.m., and the feed/min.
Move the longitudinal slide so as to clear the cutter from
Set the r.p.m. cutter rotation and table feed. the workpiece. (Fig 4)
If a higher r.p.m. is set the cutting edges may
get blunt, and if a lower r.p.m. is set the cutting
time will be more.
Set the nearest lower speed and feed available if the
machine does not have the exact values.
By using a hand traverse of the vertical, cross and
longitudinal, position the work such that the slitting saw
is close to the top of the work. (Fig 2)

By moving the vertical slide upward, apply a depth of cut.


(Fig 5)
Lock the vertical slide.
If the depth of the groove is more by 3 to 4 times than that
of the thickness of the cutter (width of the groove), then
Set the workpiece under the slitting saw such that the the total depth of the groove should not be achieved in the
distance (x) is as indicated in the drawing.(Fig 3) first attempt. It should be completed with 2 to 3 passes.

For this, move the cross-slide manually. Check ‘x’ distance Set the nozzle of the coolant pipe and start the coolant
with a vernier depth gauge. pump.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.77 31


- Check the build up edge is generated in the teeth of
the slitting saw.

Start the spindle.


Mill the groove.
Observe the following points during grooving.
Move the table to its initial position. Check the dimension
Apply only manual longitudinal feed. This facilitates
(depth) by a vernier caliper. (Fig 6)
withdrawing the workpiece from the cutter if it jams into
the cut during cutting. If required, take further cuts till the required depth is
achieved.
Ensure that there is no abnormal noise in the machine
during cutting. Deburr and remove the workpiece.
If abnormal noise is generated: Keep the floor around the machine clear of
chips and wipe off spilled cutting fluid
- reduce the r.p.m and feed
immediately. Use sawdust, sweeping or
- check the sharpness of the cutter special oil absorbing compound on slippery
floors.

Mill angular surface on horizontal milling machine


Objective: This shall help you to
• mill an angular surface on a horizontal milling machine.
Mark the workpiece as per drawing. Punch witness marks Select an angular milling cutter.
on the lines. (Fig 1)
Selection of the angular milling cutter
depends upon the angle to be milled.
There are 90°, 60° equal angle cutters. And 45°,30° single
side angle cutters.
Here select 90°equal angle cutters. (Fig 2) The cutter
thickness should be more than the width of the ‘V’ groove.
Ensure that the cutter is sharp and
undamaged.
Select and mount the long arbor on the horizontal milling
machine spindle.
Mount an equal angle cutter of 90° on the long arbor.
(Fig.3)
Calculate the r.p.m for the given material and cutter. Set
Mount a plain machine vice on a horizontal milling machine the nearest lower speed and feed available on the
such that the vice jaws remain parallel to the column. machine.
Select pair of parallel blocks which will lift the workpiece, Use hand feed in vertical, longitudinal and cross directions
bringing the top surface of the workpiece above the vice to position the workpiece such that the cutter is close to
jaws.
the top surface of workpiece. (Fig 4)
Clamp the workpiece in the machine vice.

32 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.77


Measure the thickness of the cutter (T).
Find out the centre distance of the ‘V’ groove from the
Set the datum at the top surface using tissue paper. (Fig.7)
edge[X].
Now Y = X - T/2.

Move the table to the left hand side to clear the cutter and
workpiece. (Fig 8)
Unlock the vertical slide.
Set the depth of cut of 2 mm by vertical hand feed.
Set the Y distance on the depth gauge or vernier caliper.
(Fig 5) Lock the vertical slide.
Use the cross - hand feed and adjust the workpiece such Adjust the coolant nozzle and start the coolant pump.
that the cutter surface and the workpiece edge are at [Y]
distance. Start the machine spindle.

Ensure the dimension with a vernier caliper depth gauge. Move the table to the right hand side slowly and mill the
groove by rotating the longitudinal hand wheel manually.
Set the spindle to clockwise direction. (Fig 6) (Fig 9)
Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.77 33
Adjust the cross -side to correct the error.
Lock the cross - slide.
Unlock the vertical slide and set final depth by rotating
the vertical slide manually. (Fig 11)

Lock the vertical slide.


Start the machine spindle and mill the ‘V’ groove.
(Fig 12)
Apply automatic feed if your machine permits.
If not, apply manual feed.
Stop the machine spindle.
De - clamp and deburr the sharp edges at the milled
surface.
Check the ‘V’ groove for the following parameters.
 Central position
 Depth of groove

Stop the spindle.


Move the table to the left hand side to clear the cutter
from the workpiece.
Check the position of the ‘V’ groove layout for any error.
(Fig 10)

Be thoroughly familiar with the placement of


the stop lever.

34 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.77


Capital Goods & Manufacturing Exercise 2.2.78
Machinist - Milling
Make concave surfaces with an accuracy ± 0.02mm
Objectives: At the end of this exercise you shall be able to
• layout the job as per the drawing using a vernier height gauge and spring divider
• align the job with respect to the cutter
• mill a concave surface and check the concave surface using a radius gauge.

Job Sequence
• Check the dimensions of the job.
• Lay out the job for concave milling as per drawing.
• Hold the job in the vice for milling the concave surface.
• Mount the convex milling cutter of Ø90 x 10R x 27mm
bore on the arbor and set the spindle speed to 60
r.p.m.
• Align the job such that the cutter width is symmetrical
with the centre line of the concave marking, and mill
the concave surface. (Fig 1)
• Deburr the job and measure by a radius gauge.

35
Skill Sequence
Mill a form concave surface on plain milling
Objective: This shall help you to
• mill a concave surface on plain milling machine.

Mark the job as per drawing and put witness marks.


Mount a plain machine vice at the middle of the table on
the milling machine such that the jaws are perpendicular
to the column.
Hold the workpiece in the vice on a pair of parallel blocks
such that the profile marking is 10 to 15 mm above the vice
jaw surface.
Select a convex milling cutter which suits the form of the
workpiece.

Ensure that the cutter is sharp and undamaged.


After completion of the first cut, return the workpiece to its
Calculate the r.p.m. feed per minute and set on the
original position. Confirm the form whether if it is in the
machine.
centre as per the marking. If it is not do the necessary
Mount the selected cutter on the arbor of the plain milling adjustment by moving the cross- slide and lock the cross
machine. slide.
Set the nearest lower r.p.m. for form cutters. Unlock the vertical slide.
If a higher r.p.m. is set chatter marks may Apply 4 to 5 mm depth of cut for rough milling.
appear on the cut surface.
Start the spindle.
Bring the job to the central position with respect to the
Rough out the form by feeding the longitudinal slide
centre. This is to be done visually, and be confirmed after
against the rotation of the cutter.
cutting a shallow cut. (Fig 1)
Stop the spindle.
Clear the job from the cutter.
Unlock the vertical slide.
Apply the necessary depth of cut.
Reset the feed at a low rate of [0.02 to 0.03 mm/tooth] for
finishing the profile.
Start the spindle.
Bring the job near to the cutter longitudinally and set the
automatic feed.

If any error is found adjust the work suitably. After completion of the cut, disengage the auto-feed and
stop the machine, deburr and check the form of the profile
Clear the job from the cutter to do ‘up-milling’. The job is using a gauge. (Fig 3)
to be fed against the cutter rotation. In form milling, if the
surface in contact is more, more cutting force is required. De-clamp the job.
In down-milling the cutter may tend to slip over the job.
Lock the cross-slide.
Apply 1 mm depth of cut and lock the vertical slide.
Set the coolant nozzle and start the coolant pump.
Start the spindle.
Feed the job against the cutter rotation by rotating the
longitudinal slide. (Fig 2)
Stop the machine.

36 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.78


Capital Goods & Manufacturing Exercise 2.2.79
Machinist - Milling
Make convex surfaces with an accuracy ± 0.02mm
Objectives: At the end of this exercise you shall be able to
• layout the job as per the drawing using a vernier height gauge and spring dividers
• align the job with respect to the cutter
• mill a convex surface and check the convex surface using a radius gauge.

Job Sequence
• Set and hold the job for convex milling. • Replace the cutter with a concave milling cutter ø90
x 10R x 27 mm bore and set the speed at 60 r.p.m.
• Mount two side and face milling cutters of the same
size ø100 x 15 x 27 mm bore with a spacer of 20mm • Align the job with reference to the cutter and mill the
in between for straddle milling. Set the speed to 90 convex surface. (Fig 2)
r.p.m. • Deburr the job and measure by a radius gauge.
• Align the job with reference to the cutter and mill the
job by straddle milling to a depth of 10 mm in two
passes of 5 mm each. (Fig 1)

37
Capital Goods & Manufacturing Exercise 2.2.80
Machinist - Milling
Straddle milling operation with an accuracy ± 0.02mm
Objectives: At the end of this exercise you shall be able to
• layout the job as per the drawing with a vernier height gauge
• set the job on the vice for straddle milling
• mount two sides and face milling cutters on the arbor for straddle milling
• straddle-mill the job to an accuracy ± 0.02mm
• check the size and the steps with a vernier caliper and vernier depth gauge.

Job Sequence
• Check the dimensions of the block. (Job) • Align the job with reference to the cutter.
• Blocking up as per drawing. • Mill in two stages (Fig 1) by giving a depth of cut of
4mm each.
• Mark the dimensions as per drawing and punch
witness marks. • Deburr and measure the dimensions.
• Hold the job on a machine vice such that the job will
be 10mm above the vice jaw.
• Mount two side and face cutters of size Ø100x 12x
32mm bore for straddle milling with a spacer of 15
mm size.
• Set the r.p.m. closer to 70.

38
Skill Sequence
Mount cutter for straddle milling and straddle mill
Objective: This shall help you to
• mount a cutter for a straddle milling.
Set up the plain machine vice on the machine table Mount the cutters on the arbor with spacers in between.
Hold the job in the machine vice. Ensure that both the cutters are of the same
type and dimension and have a right hand
Ensure that burrs are removed from the job by
helix.
using a smooth flat file before holding.
Be sure to insert key into both the cutters.
While holding the job. ensure that the longer side of the
job is always kept parallel to the jaw plates irrespective of
the position of the slots to be milled. This gives maximum
grip to the workpiece. (Fig 1)

Calculate the r.p.m and set the spindle speed.


Set to the nearest lower speed available if the machine
does not have the exact value.
Position the cutters in line with the slots to be cut by
adjusting the table. (Fig 4)

Select spacing collars to make up the dimension between


the inner edges of the slots to be cut.
In the case of plain side and face cutters, the length of
the collar shall be equal to the distance between the inner
edges of the slots. (Fig 2)

Start the spindle.


Raise the work table until the cutters just touch the top
surface of the workpiece. Confirm visually that the cut is
exactly in line within the slots; if it is not in line, adjust
the table. (Fig 5)
Set the vertical scale to zero.
Move the table to bring the cutters clear of the workpiece.
Stop the spindle.
In the case of staggered tooth side and face cutters Set the longitudinal feed stops so that the cutters will
calculate the length of space considering the tooth clear each end of the workpiece. (Fig 6)
offset.(Fig 3)
Set the depth of cut using vertical hand feed.
Fix the long arbor in the machine spindle.
Lock the vertical slide.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.80 39


Stop the spindle and move the table longitudinally back
to the initial position.
Deburr the edges and measure the distance between the
slots by a vernier caliper.
Ensure that the dimension is correct.
- If not check the length of the space between the
cutters.
- Replace the spacers of correct size. If spacers of the
correct size are not available grind the face of the
spacer. (Fig.8)

Start the machine and mill the slots.


Stop the spindle when the automatic table feed stops.
Clear away the chips from the slot.
Return the table to the initial position.
Position the coolant pipe and guard. Check the depth and take further cuts until the required
depth is accomplished.
Start the spindle.
Remove the burrs from the edges of the slots.
Put on the safety goggles. Check the workpiece dimensions with the help of a vernier
caliper. (Fig 9)
Calculate the correct feed.
Select the nearest lower feed available if the machine Avoid close proximity to the rotating cutter
does not have the exact value. always. Otherwise you may injure yourself.

Engage the coolant pump.


Mill the slot and feed the table up to 5 to 10mm. (Fig 7)

40 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.80


Capital Goods & Manufacturing Exercise 2.2.81
Machinist - Milling
Gang milling operation with an accuracy ± 0.02mm
Objectives: At the end of this exercise you shall be able to
• layout the job as per the drawing with a vernier height gauge
• set the job on the vice for gang milling
• mount the cutters for gang milling.

Job Sequence
Mount machine vice perpendicular to the column on a Select and mount the long arbor on the horizontal milling
horizontal milling machine. machine.
Mark the job as per drawing. Put witness mark on the Keeping in view the drawing and dimensions, hold the
lines (Fig 1) cutter on the machine.
Calculate the speed and feed for gang milling.

Consider the average diameter for calculating


the r.p.m.

Set a lower range of r.p.m. for gang milling.


Set the datum to the reference sides for the vertical and
cross-slides. (Fig 2)

Ensure that the workpiece projects


sufficiently above the vice jaw to avoid
damage to the vice jaw and resetting of the
workpiece.
Select the suitable form and diameters of milling cutter
having the same bore diameter.

41
Lock the cross-slides. Clear the workpiece from the
cutters by moving the longitudinal side to the left side.
Apply 2 to 3 mm depth of cut using the vertical slide.
Start the spindle and the coolant pump.
Move the longitudinal slide to bring the workpiece in
contact with the cutter. Feed the workpiece slowly. (Fig.3)
Use manual feed to avoid any jerks on the machine or
cutter. See to it that sufficient coolant flows on the cutter
to avoid blunting of the cutting edges.
After completion of the cut, stop the spindle.
Rewind the longitudinal slide to its original position. Apply
another rough cut between 3 to 4 mm and complete
roughing of the profile. By applying 0.5 to 0.8 mm depth
of cut finish the profile.
For the finishing cut, use automatic feed to get a better
surface finish at the profile.

42 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.81


Capital Goods & Manufacturing Exercise 2.2.82
Machinist - Milling
Make dovetail fitting (male & female) on milling machine with an accuracy ±
0.02mm
Objectives: At the end of this exercise you shall be able to
• lay out the job as per the drawing using vernier height gauge and vernier bevel protractor
• mount and align the job with respect to the cutter
• mill the internal and external dovetails to an accuracy of ± 0.02 mm
• check the dimensions of the internal and external dovetails using rollers and assemble it.

43
Job Sequence (Part ‘A’) Job Sequence (Part ‘B’)
• Mark the dovetail as per drawing • Mark the dovetail as per drawing.
• Calculate the r.p.m for the selected cutter and set it. • Calculate the r.p.m for the selected cutter and set it.
• Set a end mill cutter with collet chuck on vertical • Set the end mill cutter on vertical milling machine
machine spindle. spindle.
• Set the workpiece on the machine vice. • Set the block on the vice of vertical milling machine.
• Set the datum on the top surface of the block using • Touch the vertical surfaces of the block by end mill
tissue paper. cutter and cut shoulders 13x15.6mm both side of the
block.
• Cut the slot 36 x 15.6mm between the dovetail marking.
• Set the dovetail cutter for clockwise direction on vertical
• Set the dovetail cutter for clockwise direction on
milling machine changing end mill cutter.
vertical milling machine by changing end mill cutter.
• Set the datum on the surface of the block using tissue
• Set the datum on the bottom surface of the slot using
paper.
tissue paper
• Set the vertical surface by touching the edge of the
• Set the vertical surface also by touching the edge of
dovetail cutter 60° x 25 mm cut first side dovetail then
the dovetail cutter 60° x 25 mm shank dia.
another side of the dovetail upto punch line.
• Cut first side and then another side cut of the dovetail
• Check the dovetail by rollers method.
with dovetail cutter.
• Fit the job with female part of the dovetail
• Check the size ofdovetails with rollers and vernier
caliper. (Part- A).

Skill Sequence
Mount dovetail cutter and mill external and internal dovetail on vertical milling
Objective: This shall help you to
• mill internal and external dovetail.
Internal dovetail Mount the collet chuck on the vertical milling machine.
Mark the job as per drawing and put witness marks. Hold the dovetail cutter in the collet chuck and tighten it
Mount the machine vice such that the vice jaws are using a hook spanner.
perpendicular to the column. Ensure that the cutter is sharp and not damaged.
If the length of the job is more than the width of the vice Ensure that the cutter is not gripped overhung.
jaws, mount the vice such that the jaws are parallel to the
Calculate the r.p.m. for selected cutter and set it.
column. And if the length of the job is smaller than the
width of the vice jaws mount the machine vice such that Calculate the feed per minute to the selected cutter, and
the jaws are perpendicular to the column. set to the nearest lower feed available.
Set the cutter for clockwise rotation.
Hold the job in the machine vice on the pair of parallel
blocks (C) such that the bottom surface remains 5 to Position the workpiece so that the cutter is over the
6 mm above the vice jaws (B). (Fig 1) previously milled slot.
Set the datum on the bottom surface of the slot (Fig 2)
using tissue paper.

Mill the central slot by the end mill cutter.


Select the dovetail cutter to suit the dovetail groove
dimensions.
44 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.82
Set the datum at the vertical face of the slot by touching
the edge of the dovetail cutter. (Fig 3)

Clear the workpiece from the cutter by moving the


longitudinal slide. (Fig 4)

Engage the longitudinal feed and mill the dovetail. When


the feed stops, stop the spindle. Return the table to the
starting position.
Calculate the roller dimensions using 6 mm rollers.
Check the dimension (X1) by vernier calipers and roller.
(Fig 7)

Set the longitudinal feed stops so that the cutter will clear
each end of the workpiece. (Fig 5)

Find out the difference between the actual dimension and


the calculated dimension.
Unlock the cross slide.
Adjust the cross slide so as to get the calculated dimension.
Lock the cross slide.
Start the spindle.
Move the longitudinal slide manually and mill the dovetail.
Stop the spindle.
Bring the workpiece to its original position.
Unlock the cross-slide.
Check the roller dimensions (X1) and confirm.
Use the hand cross-feed and set the depth of cut for the
Mill the opposite dovetail following the required steps.
first roughing cut of about 1to 5 mm. (Fig 6)
Ensure that the feed is from the opposite side of the
Lock the cross-slide.
previous one to adopt up-milling.
If the depth to be milled is more than 5 mm then rough out
Check (Y1) dimension by using a 6 mm dia. roller and
the dovetail in two passes.
vernier caliper. (Fig 8)
Adjust the coolant nozzle directing it towards the cutting
External dovetail
edges.
Mark the job as per the drawing and put witness marks on
Start the spindle and coolant pump.
it.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.82 45


Take the workpiece to the left side to clear from the cutter.
Apply a depth of cut (0.2 to 0.3 mm) depending upon the
material to be rough cut by rotating the cross-slide.
Lock the cross-slide.
Move the longitudinal slide slowly towards the rotating
cutter and rough cut the dovetail on one side.
Stop the spindle.
Mount the plain milling vice on the vertical milling such
Calculate the roller dimension X3 and check it with a
that the vice jaws are perpendicular to the column.
vernier caliper.
Hold the job in the vice on a pair of parallel blocks. The
Use a 6 or 8 mm dia. roller. (Fig 10)
bottom surface of the dovetail marking should remain 5
to 6 mm above the vice jaws.
Mount the collet chuck on the vertical milling
machine.
Mill the hatched portion using an end mill cutter by
maintaining X2 and Y2 dimension to suit the dovetail
groove dimensions. (Fig 9)

Adjust the cross-slide to get the correct calculated


dimension.
Start the spindle.
Move the longitudinal slide towards the cutter and finish
the dovetail.
Check X3 dimension by using 6 or 8 roller.
Calculate X4 dimension using a 6 or 8 roller.
Mill the opposite dovetail following the necessary steps.
Check X4 dimension by using 6 or 8 dia. roller.
(Fig 11)
Deburr and remove the job.

Mount the dovetail cutter in the collet chuck and tighten.


Calculate and set the r.p.m. and feed for the dovetail
cutter.
Set the datum at the bottom surface of the step and the
vertical face of the step, using tissue paper.

46 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.82


Capital Goods & Manufacturing Exercise 2.2.83
Machinist - Milling
Make T-slot fitting (male & female) on milling machine with on accuracy ±
0.02mm
Objectives: At the end of this exercise you shall be able to
• layout male and female ‘T’ slot using vernier height gauge
• mill female ‘T’ slot on vertical milling machine
• mill male ‘T’ slot
• match part ‘A’ with part ‘B’.

47
Job Sequence (Part ‘A’)
• Mark the ‘T’ slot as per the drawing.
• Mount and align the vice on the vertical milling ma-
chine.
• Hold the job in the vice supported with parallel blocks.
(Fig 1)

• Mill the ‘T’ slot on the right side to size. (Fig 3)


• Deburr and check the dimensions of the ‘T’ slot with a
telescopic gauge and a 25 to 50 mm outside microme-
ter.

• Mount the ‘T’ slot cutter Ø25 x12 mm on the machine


with an adapter and collets.
• Align the job for ‘T’ slot milling with respect to the
cutter. (Fig 2)
• Set the spindle nearest to 275 r.p.m.
• Mill the ‘T’ slot on the left side to size. (Fig 2)
• Deburr and check the size.

Job Sequence (Part ‘B’)


• Mark the 'T' as per drawing • Mount a 'T' slot cutter of Ø25 x 12 mm into the vertical
milling machine spindle
• Mount and align the vice on the horizontal milling
machine. • Set the r.p.m near to 275

• Hold the job in the vice supported with parallel blocks. • Mill the 'T' on the vertical milling machine check the
dimension of the 'T' slot with vernier caliper and out
• Cut the both side of the block by side and face milling side micrometer.
cutter on horizontal milling machine.
• Fitting the job with the female part of part A.

Mill a ‘T’ slot on vertical milling machine


Objective: This shall help you to
• mill a ‘T’ slot on a vertical milling machine.

Mark the workpiece as per drawing. Remove burrs if any. Select a collet of the same size as that of the cutter shank
and set the cutter in the chuck. (Fig 1)
Mount the plain machine vice on the table with its jaws
parallel to the column.
Keep the workpiece on a pair of parallel blocks such that
the workpiece is above the jaws of the vice.
Clamp the workpiece.
Mill the slot as per the given dimension.
Select a ‘T’ slot cutter to match the ‘T’ slot dimensions to
be cut.

Check if the cutter is sharp and undamaged.

48 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.83


Start the spindle for a while to ensure that the
cutter is running true and in the correct
direction, and stop the spindle.

Set the datum for the top and side using tissue paper.
(Figs 2 and 3)

Use longitudinal hand feed and move the table slowly until
the cutter begins to cut the workpiece. (Fig 5)

Ensure that the table movement is gentle and smooth to


avoid damage to the cutter.
Start the coolant.
Set the spindle speed and table feed. Engage the longitudinal feed and mill the slot.
Move the table to clear the cutter from the workpiece by Ensure that the chips collecting in the slot are carried
using the hand cross-feed after fixing the datum. away by the flow of the coolant while the slot is being cut.
Position the table to correct dimension (L+D/2), using In ‘T’ slot milling blocked chips may cause breakage of the
hand cross-feed, so that the cutter is into the centre of the cutter.
‘T’ slot. (Fig 4) Stop the spindle when the feed stops.
Lock the cross-slide. Clear away the chips.
Use a vertical slide and raise the table to bring the cutter Deburr the slot.
to correct depth of the ‘T’ slot.
Clear the slot and check the dimension.
Lock the vertical slide.
Repeat the process, if more than one slot are to be milled.
Set the longitudinal feed stops so that the cutter will clear
both ends of the workpiece. Put all the oily rags, used to wipe the machine,
Start the spindle. in a metal container that can be closed tightly.

Ensure that the guard is in position and safety


goggles are put on. This is required for personal
safety.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.83 49


Capital Goods & Manufacturing Exercise 2.2.84
Machinist - Milling
Demonstrate indexing head
Objectives: At the end of this exercise you shall be able to
• identify the different types of indexing
• identify the parts of a universal indexing head.

Job Sequence
• Mount the indexing head on the machines and
demonstrate.
• Indentify the parts of indexing head and write it in the
table.
Table 1

Sl.No Name of parts


1
2
3
4
5
6
7
8
9
10

50
Capital Goods & Manufacturing Exercise 2.2.85
Machinist - Milling
Set and align indexing head with reference to job on milling machine
Objectives: At the end of this exercise you shall be able to
• mount and align the dividing head
• set the dividing head for direct indexing.
Job Sequence
Keep your hands clear of the bottom of the
A dividing head is used to hold workpieces that dividing head when lowering the head.
must be machined with accurate division on
the circumference. Setting head horizontal
‘Zero’ the index scale.
The universal dividing head is the type most
commonly used. Insert the tapered shank test-bar in the spindle, making
sure both are clean. (Fig 3)
Clean the table top and Tee slots thoroughly.
Insert a rod of suitable length through the head spindle to
protrude 75 to 100 mm at each end and tighten the chuck
on the bar.
Sling the head with a strong rope. (Fig 1)

Disengage the worm from the worm-wheel for rapid indexing.


Set the dial indicator as shown in Fig 4.

Lift the indexing head with help of crane and position it on


the milling machine table.
The rope should be free from wear. The crank
hook should be at the centre of the head to
balance the head. Stand clear when lifting to Rotate the head manually to ensure the bar is running true.
avoid any injury to you in case of an accident. Take a reading with the dial indicator as near the spindle
nose as possible. (Fig 5)-A
Clean the base of the dividing head.
Lower the head gently and engage the tenons in the table
slot and tighten the securing bolt. (Fig 2)

Take the reading at the opposite end of the bar.


(Fig 5)-B Note any variation.
In case of any variation, remove the dial indicator and
slightly loosen the locking nuts at the back of the head.
Tap lightly with a soft hammer in the required direction and
check again.
51
Capital Goods & Manufacturing Exercise 2.2.86
Machinist - Milling

Make square job by direct/ simple indexing method with an accuracy ±


0.02mm
Objectives: At the end of this exercise you shall be able to
• mount the index head on the table and align it parallel to the column face
• hold the job in the three-jaw chuck and true to face
• set the index head for direct indexing
• mill the square on the job by direct indexing to an accuracy of ± 0.02 mm
• check the distance across the flats of the square using a vernier caliper.

Job Sequence
• Clean the table and dividing head free from dirt (and) • Mount the 18 mm end mill.
burrs and align the dividing head on the vertical milling • Set the r.p.m. closer to 300.
machine table.
• Set the datum at the highest point on the diameter.
• Set the dividing head for direct indexing.
• Mill the surface flat maintaining the dimension 30.0mm.
• Hold the job on Ø25 in a three-jaw chuck of the dividing
head. • Index the job by 180°.
• Mill the flat surface maintaining the size to 25 mm.
• Index the job by 90°.

• Support the end with the tail stock.


• Set the index plate to zero position.

52
• Mill the flat surface maintaining the size to 30.0mm
(Fig 3)
• Index the job by 180°.
• Mill the flat surface maintaining the size to 25 mm.
• Deburr, check and confirm the dimensions of the
square.

Skill Sequence
Milling square and hexagon
Objective: This shall help you to
• mill flats on shafts.

Some shapes of slots are shown in Fig 1 which are Mount the collet chuck and end mill cutter or stub arbor
normally done by direct indexing. with a shell end mill cutter on the spindle nose of the
machine. (Fig 3)

Mount and align the index head on the vertical milling


machine.

Ensure that the index head is mounted at the


extreme left side on the machine table to
facilitate easy approach for cutting.
Calculate and set the r.p.m. and feed per minute for the
Set the index head for direct indexing.
above selected diameter of the cutter.
Mount a three-jaw chuck on the index head. (Fig 2)
Set a lower range of speed and feed to avoid
metal cutting problems.

Engage the locking pin into the index plate and note the
number on the plate.
Bring the workpiece in line with the cutter by moving the
cross-slide. Raise the top surface of the job 5 to 6 mm
above the face of the cutter. (Fig 4)

Hold the job in the three-jaw chuck at the index head and
lock it.

The portion to be milled should be 10 to 20 mm


away from the face of the chuck jaw to avoid
damage to the cutter and the chuck.

Select a suitable diameter of an end mill cutter or shell end


mill cutter to cut the entire surface in one pass.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.86 53


Start the spindle. Unlock the vertical slide and apply a depth of cut equal to
the difference in dimension Y and the measured dimension,
Move the longitudinal slide towards the cutter till the cutter
and lock.
just touches the end face of the workpiece.
Start the spindle.
Stop the spindle.
Move the cross-slide and mill the first side of the square.
Set the datum for the longitudinal slide.
Stop the spindle.
Clear the cutter by moving the cross-slide.
Bring the workpiece to its original position.
Move the longitudinal slide to the required length of the
square to be milled, and lock it. Remove the locking pin of the index plate.
Lower the vertical slide to clear the cutter. Unlock the index head spindle.
Start the spindle. Index the work by 180°.
Bring the workpiece under the cutter by moving the cross- Insert the locking pin in the hole at the index plate
slide. (12 holes). Lock the index head spindle.
Raise the vertical slide slowly manually. As soon as the Start the spindle.
cutter touches the top surface of the workpiece, stop the
Move the cross-slide manually and feed it slowly. (Reduce
spindle.
the depth of cut if it is more)
Clear the workpiece from the cutter by moving the
Complete the milling of the opposite side (side 3). (Fig 7)
cross-slide.
Set the graduated dial to zero at the vertical slide.
Apply a 0.5 mm depth of cut and lock the vertical slide.
Set the coolant nozzle.
Start the spindle and the coolant pump.
Move the cross-slide and mill the first side by hand feed.
(Fig 5)

Stop the spindle.


Bring the workpiece to its original position and check flat
to flat.
Unlock the index head and index the workpiece by 90°
(6 holes).
Insert the index pin into the hole of the index plate and lock
the index head.
Start the spindle.
Move the cross-slide and feed it manually, and complete
the milling of the 2nd side.
Stop the spindle.
Repeat the above procedure to mill the 4th side.
Bring the workpiece to the original position.
Check the Y-dimension with an outside micrometer. Check the job for size.
(Fig 6)
For milling a hexagon the same procedure is adopted and
the sides are milled as numbered in Fig 8.
To determine the depth of cut use the following formula.

C F
The depth of cut(d) is (Fig 7)
2
If the 30 hole circle is used, the division is as shown in
Fig 9.
The hexagon is shown in the centre with a dotted line. To
index from one side to the adjacent side, the crank is
rotated to

54 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.86


30 number of holes 
 5 holes
6 (number of divisions)

That means that you place the pin of the crank into the fifth
hole and pass over 4 holes. (Fig 10)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.2.86 55


Capital Goods & Manufacturing Exercise 2.2.87
Machinist - Milling
Make hexagonal job by simple indexing method with an accuracy ± 0.02mm
Objectives: At the end of this exercise you shall be able to
• mount the index head on the table and align it parallel to the column face
• hold the job in the three jaw - chuck and true to face
• set the index head for direct indexing
• mill the hexagon on the job by direct indexing to an accuracy of ± 0.02 mm
• check the distance across the flats of the hexagon using a vernier caliper.

Job Sequence • Mill the surface flat maintaining the dimension 34.64.
(Fig 2)
Clean the table and dividing head free from dirt and burrs
and align the dividing head on the vertical milling machine
table.
• Set the dividing head for direct indexing.
• Hold the job on 30 in a three-jaw chuck of the dividing
head.
• Support the end with the tailstock.
• Index the job by 60°.
• Set the index plate to zero position.
• Mill the surface flat maintaining the size 37.32.
• Mount the 18 mm end mill.
(Fig 3)
• Set the r.p.m. closer to 300.
• Set the datum at the highest point on the dia
meter. (40)
• Mill the surface flat maintaining the dimension 37.32.
(Fig 1)

• Index the job by 180°.


• Mill the flat surface maintaining the size 34.64.
• Repeat the above procedure and complete the
hexagon.
• Deburr, check and confirm the dimensions of the
• Index the job by 180°. hexagon.

56
Capital Goods & Manufacturing Exercise 2.3.88
Machinist - Advanced Turning

Checking of alignment of lathe centres and their adjustments


Objectives: At the end of this exercise you shall be able to
• mount the test bar in lathe between centres
• set the dial test indicator
• check the centre alignment using test bar with dial test indicator.

Job Sequence
• Clean the centres of the lathe ane the centres drilled • Adjust the cross slide so that the indicator needle
holes in the test bar. registers about are half of a revolution on the dia. at the
tail stock end.
• Mount the test for required tighten the between centres
and tighten the tail stock spindle space clamp. • Move the carriage to the left by hand until the indicator
registers on the diameter at the handstock end.
• Mount a dial indicator in the tool post or on the lathe
carriage. • Note the indicator reading.
• The contact point should be on the space centre of the • If the readings are not the same
bar and the indicator plunger should be in a Vertical • Move the carriage until the indicator again registers on
position. the tailstock end diameters.
• Loosen the tailstock clamp nut.
• Using the tailstock adjusting screw.
• Move the tailstock in the proper direction.
• The amount of movement should equal the difference
between the indicators readings.
• Tighten the loose adjusting screw to lock the upper
part of the tailstock in place.
• Tighten the tailstock clamp nut and recheck to make
sure that the test bar still fits snugly between centres.
• Repeat these steps until the indicator readings at the
two ends are the same.

57
Capital Goods & Manufacturing Exercise 2.3.89
Machinist - Advanced Turning

Turning practice-between centres on mandrel (gear blank) with an accuracy


± 30 minutes
Objectives: At the end of this exercise you shall be able to
• mount the work on mandrel (Mandral)
• swivel compound rest requird angle
• turn bevel gear blank.

Job Sequence
• Check the blank size. • Turn the taper to have a face width of 21mm
• Mount the work on a mandrel. • Again swivel the compound rest to angngle 45°
degrees.
• Set the mandrel in between centres.
• Hold the job on the mandrel
• Grind and set the tool in the tool post.
• Turn the taper to have a width of 13 mm.
• Swivel the compound rest to an angle of 47° 42°
degrees. • Check angle with vernier bevel protractor.

58
Skill Sequence
Measuring with vernier bevel protractor
Objectives: This shall help you to
• check the various angles of the machined parts up to an accuracy of ± 5’
• check the straightness of the machined surface with reference to the other vertical surface.

The vernier scale is duplicated to read either side of the zero As the least count is 5’ multiply this number by 5. (i.e 4 5
graduation of the main scale. If you read the main scale in - 20’)
the clockwise direction. Continue reading the vernier scale
Add this result to the main scale reading of 50° i.e 50° + 20
also in a clockwise direction. Always make sure that the
-50° 20’.
vernier scale reading is added to the main scale.
Similarly the reading for figure 2 may be obtained as 52°
Method of using clockwise reading
45’. (Fig 2)
Set the angular surface of the workpiece between the blade
and the face of the base and lock the blade and inner
discfrmly with the locking device.
The position of the vernier scale with reference to the main
scale is shown in Figure 1.

Method of checking the straightness with


reference to the vertical surface

Set the blade and base firmly on the machined surface.


Lock the blade and base in position with the help of the
locking device.
Read the vernier scale with reference to the main scale.
Read the degrees of teh main scale up to the graduation 0 If the ‘0’ graduation of the vernier scale and 90° of th main
of the vernier scale i.e. 50°. scale coincide, the machined faces are at right angles, i.e.
90°
Continue reading on the appropriate vernier scale (towards
the left hand side). Note teh number of lines in the vernier If the ‘0’ graduation of the vernier scale does not coincide,
scale the coincide with a division of the main scale. (i.e. 4 read the appropriate vernier scale and find the error in
th division of the vernier scale is coinciding with one of the degrees and minutes.
main scale division line)
The error shows the deviation of surface from the
straightness.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.89 59


Capital Goods & Manufacturing Exercise 2.3.90
Machinist - Advanced Turning

Taper turning by swivelling the cross - slide (Taper turning attachments)


Objectives: At the end of this exercise you shall be able to
• set the compound rest to the specific angle
• turn taper using the compound slide method within an accuracy ±30’
• turn the external taper by the compound rest method.

Job Sequence
• Check the size of the raw material. • Set the taper turning attachment for the required
amount of taper 1° 26'.
• Hold the job in a four jaw chuck and true it. • Confirm the graduations on the bracket of the taper
• Set the required tools in a four way tool post. turning attachment whether for half included angle of
the taper or full, and then set it.
• Face one end and centre drill.
• Taper turn, engaging the power feed for a short length
• Reverse the job, face the other end to maintain a total and maintaining a smooth surface.
length of 130 mm and centre drill.
• Adjust the setting, if needed, to get proper matching.
• Hold the job in a four jaw chuck and true it.
• Complete the taper turning to suit the gauge up to the
• Support the job on the tailstock keeping 115 mm from gauge plane.
the chuck face, and true.
• Dismount the chuck from the spindle nose and fix the
• Turn a diameter 24.05 mm to the maximum possible spindle sleeve to the nose bore.
length and check with a micrometer.
• Insert the job in the sleeve and set the machine r.p.m.
• Position the turning tool and turn step dia. to 18 mm.
• Swivel the compound slide to 30° away from you.
• Form radius at the edge of 18 mm.
• Rough and finish turn taper to get a 60° included
angle.

60
Skill Sequence
Producing taper by using taper turning attachment
Objectives: This shall help you to
• set the taper turning attachment to the required angle
• produce taper by using a taper turning attachment.

A taper turning attachment provides a quick and accurate Set the required r.p.m.
means of turning tapers.
Feed the cutting tool in until it is about 6 mm from the work
The following procedure is to be followed during turning surface.
taper using a taper turning attachment.
Remove the locking screws which connect the cross -
Check for backlash between the guide bar and the sliding slide and the cross - slide nut.
block, and adjust, if necessary.
Use the binding lever to connect the cross - slide extension
Clean and oil the guide bar. and sliding block.
Loosen the locking screws, then swivel the guide bar to the Insert a suitable plug in the hole on the top of the cross
required angle. slide to protect the cross - slide screw from dirt and metal
chips.
Tighten the locking screws.
The compound slide must now be used to feed the cutting
Adjust the base plate until the ends of the guide bar are
tool into the work.
equidistant from the cross - slide extension.
Move the carriage to the right until the cutting tool is about
Set up the cutting tool on exact centre.
12 mm away from the right hand end of the work piece.
Any error will result in an in correct taper
This removes any play in the moving parts of
the taper turning attachment.
Mount the work piece on the chuck or between centres.
Adjust the carriage until the cutting tool is approximately Switch on the lathe.
opposite to the centre of the tapered section.
Take a light cut about 2 mm long and check the end of the
Lock the clamping bracket to the lathe bed to secure the taper for size.
taper turning attachment in this position.
Set the depth of the roughing cut.
When using a plain taper turning attachment, Machine the work as with plain turning.
follow the steps given below at this stage.
Remove the play by moving the cutting tool 12 mm beyond
the right hand end of the work at the beginning of each cut.
Adjust the top slide so that it is parallel with the cross
slide, I.e at 90° to the work. Check the taper for fit.
Set up the cutting tool for the correct position. Readjust the taper turning attachment, if necessary, take
a light cut and recheck the taper.
Wear safety goggles.
Finish the taper to size and fit it to the taper gauge.

Turning taper by compound slide swivelling


Objectives: This shall help you to
• set and swivel the top slide of the compound rest to the required taper angle
• set the tool in the tool post
• turn the taper
• check the taper with a vernier bevel protractor.
One of the methods of turning taper is by swivelling the compound slide and feeding the tool at an angle to the axis of the
work by hand feed. (Fig 1)
Set the machine to the required rpm. Ensure that equal pressure is exerted by the
spanner for both the nuts.
Loosen the top slide clamping nuts.
Fix the turning tool in the tool post to the cor-
Swivel the top slide to half the included angle of the taper
rect centre height.
away or towards the operator as required.
Keep a minimum overhang of the tool.
Tighten the clamping nuts firmly. (Fig 2)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.90 61


Position the top slide to cover the length of the
taper turning.

As far as possible ensure that the top slide does not go


beyond the edge of the base.
Lock the carriage in position.
Touch the tool to the work surface during running and set
the cross - slide graduated collar to zero.
Bring the tool clear off the work by the top slide hand
wheel movement.
Give a depth of cut by the cross - slide and feed the tool
by the top slide hand wheel till the tool clears from the
work.

Feeding by the top slide must be uniform and


continyous.

Compound rest setup for turning various angles


Give successive cuts by the cross - slide, feeding by the
top slide each time.
Check the angle of the turned job with a vernier bevel pro-
tractor.
Adjust the swivel if there is any difference.
Continue the taper turning and finish the taper.
Compound rest setup for turning various angle is given in
table 1.

62 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.90


Table 1

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.90 63


Capital Goods & Manufacturing Exercise 2.3.91
Machinist - Advanced Turning

Make square thread (external) on a lathe with an accuracy ±0.02mm


Objectives: At the end of this exercise you shall be able to
• turn step to an accuracy of ±0.02 mm
• cut right hand external square thread.

Job Sequence
• Hold the job in a four jaw chuck, true and face both • Turn 48mm to a length of 30mm.
ends and maintain on total length of 85mm by plain
• Turn 27mm to another side maintaining length 55mm.
turning. o
• Finish chamfer 2x45 at the both end of 48mm dia.
• Centre drilling on both ends
And also chamfer at the end of 27 by V cutting tool.
• Remove the four jaw chuck and mount a driving plate
• Set the spindle speed about ¼ th of normal turning.
• Insert the head stock centre with the spindle sleeve
• Cut rough up to ¾th depth and full width by taking
and the tail stock centre also.
successive cuts up to complete thread form.
• Hold the job in a suitable carrier in between centres.
• Deburr and check using square thread gauge.

64
Skill Sequence
Grind an external threading tool
Objective: This shall help you to
• grind an external square threading tool.

Determine width and angles required for grinding the


external square threading tool.
The side clearance of the square threading tool is of prime
importance to prevent the tool from interfering or rubbing
against the vertical flank of the thread. As rule, the forward
side clearance angle (a1) is determined by adding 1° to the
helix angle of the thread and trailing side clearance angle
is obtained by subtracting 1° from the helix angle. (Fig 1)

1= (to 2°)


1=1° + Helix angle of thread
Grind the trailing side flank of the tool to maintain the side
and relief angle 1o-2o, trailing side clearance angle
2= Helix angle of thread -1° where, helix angle () and the width w0.5x(Fig.4)

Lead of thread Deburr and check the width of the angles using a vernier
 caliper and bevel protractor.
 x cord dia. of thread

The width of the nose of the square threading tool should


be equal to half of the pitch of the square thread to be cut.
W=0.5xp
Grind the front flank of the tool too get the front clearance
angle 6° to 8°. (Fig 2)
Grind the forward side flank of the tool to obtain side relief
angle 1°- 2° and forward side clearance angle 1. (Fig 3)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.91 65


Square thread
Objective: This shall help you to
• cut a square thread.

Check the diameter of the portion to be threaded as


indicated in the drawing.
Chamfer the edge of the job to 2 x 45°
Set up the gearbox to cut the required pitch of thread, and
hand of thread.
Set the square threading (roughing) tool in the tool post with
its height to the centre height of the lathe.
Set the tool square to the axis of the with the square thread
gauge. (Figs 1 and 2)
Care is to be taken to prevent overhanging of tool from the
holder to avoid chatter.
Set the spindle speed about 1/4th of the normal turning.

Cut the square thread, by repeated successive depth of


cuts to reach 3/4th width and depth of thread. (Fig 3)

Set the finishing square thread tool for finishing cuts.


Cut the square thread to full depth and full width by taking
successive cuts to complete the required thread form.
Deburr and check the square thread using a square thread
gauge.

66 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.91


Capital Goods & Manufacturing Exercise 2.3.92
Machinist - Advanced Turning

Make square thread (internal) on a lathe with an accuracy ± 0.02mm


Objectives: At the end of this exercise you shall be able to
• grind internal square threading tool
• cut internal square thread by the plunge cut method
• match square threads
• knurl the surface with medium knurl.

Job Sequence
• Check the size of the raw material. • Face and maintain 12mm.

• Hold the job in 4 jaw chuck keeping 18mm outside • Form internal chamfer 1 X 60°.
the chuck and true the job with a surface gauge. • Form external chamfer 1 x 45°.
• Set the facing tool and face one end of the job. • Hold the job keeping 10mm outside the jaws, such
• Set the R.H. turning tool and turn Ø40x20mm length. that two jaws grip the work on its face and two jaws
grip on the periphery.
• Centre drill, drill pilot hole 8mm and enlarge to 20mm
hole by drilling. • Set the line perpendicular to the lathe axis with the
help of a surface gauge align the job, if required.
• Set the boring tool and bore the drilled hole to core
diameter 21mm. • Set the facing tool to form a flat surface up to the half
of centre punch mark.
• Set the chamfering tool and form internal chamfer 1
x 60°. • Approximate feeding to the tool will be 2.6 mm
maximum.
• Set the internal square threading tool, the cutting
edge parallel to the axis. • Reset the job in a 4 jaw chuck keeping the opposite
side of the flat surface outside the jaws.
• Arrange change gears for 6mm pitch.
• While setting, keep the flat surface of the job butt
• Cut internal square thread SQ 27X6 and match with against the parallel block, and remove the parallel
the male piece. block after fixing the job.
• Reverse and true the job. • Check the sizes with a precision measuring
instrument and the thread with the mating part for the
fit.

67
Capital Goods & Manufacturing Exercise 2.3.93
Machinist - Advanced Turning

Check with thread gauge - Grinding of tool and setting in correct position
Tool grinding tool setting and checking is already given in the previous exercise 2.3.91 & 2.3.92

Capital Goods & Manufacturing Exercise 2.3.94


Machinist - Advanced Turning

Fitting of Male and Female square threaded components


Objectives: At the end of this exercise you shall be able to
• check the thread profile and depth
• adjust thread profile dimensions
• assemble male and female thread.

Job Sequence
• Clean male and female square Threaded component. • Assemble by screwing in 27x 6 female square thread
• Check the Thread dimension, pitch and thread profile into the external in27x 6 square threaded component
using Vernier caliper and Screw Pitch Gauge • Tighten the two component (male and female)

68
Capital Goods & Manufacturing Exercise 2.3.95
Machinist - Advanced Turning

Make multi-start ‘V’ thread on lathe with screw pitch gauge


Objectives: At the end of this exercise you shall be able to
• grind ‘V’ tool as per drawing
• set the turning tool ‘V’
• set the machine spindle speed for turning
• parallel turn the work by hand feed method with various depths of cuts
• turn step to an accuracy of ± 0.05 mm
• measure the dia. of the job with micrometer
• grind chamfering tool as per drawing
• set chamfering tool and chamfer the job as per drawing
• cut multi - start ‘V’ thread by thread chasing dial
• cut multi start thread by face plate method.

69
Job Sequence
• Check the raw material for its size. • Set the graduated dial of the compound rest to zero,
without any backlash.
• Hold and true the job in a four-jaw chuck so that the
job is projected to about 60mm length out of the • Set the external V- threading tool in the tool post
jaws. using a centre gauge.
• Face the end of the job. • Set the quick change gearbox to first start of the
thread to 4mm pitch.
• Turn the outside diameter to ø48mm over the
projected length. • Cut the external V- threads of 4mm pitch to full depth
by successive cuts.
• Chamfer the sharp corner of the end.
• Move the compound slide longitudinally equal to
• Reverse and reset the job in the chuck so that the
2mm referring to the graduated dial, for the second
job is projected about 65 mm out of the jaws.
start of the threads.
• Face the end of the job to 95 mm length.
• Cut the second start of the external V-threads of
• Turn the outside diameter to ø30x60mm length. 4mm pitch to full depth by successive cuts.
• Turn the undercut to 5x1.5mm. • Deburr the sharp corners.
• Chamfer the sharp corner of the end. • Check the dimensions.
• Set the angle of the compound rest to zero.

Skill Sequence

Resetting of ‘V’ thread cutting tool


Objective: This shall be able to
• reset the threading tool which has been re-sharpened by grinding.

A thread is formed by taking a number of successive cuts When the tip of the cutting tool is in line with one of the
and it may become necessary sometimes to remove the thread grooves, stop the lathe.
tool and re-sharpen it as it may get blunt or the point may
Do not disengage the half-nut.
break. The tool has to be fixed and set in a tool post in such
a way that it follows the same thread groove previously Carefully position the tip of the cutting tool in the groove
formed. with its trailing edge in contact with the trailing edge of the
thread.
The resetting of the cutting tool is necessary when
– the workpiece has moved The tool must be moved to this position by
operating the cross-slide and the compound
(shifted in the mounting accessory)
slide hand wheels.
– the tool-holder has moved
Set the graduated collars of the slides to zero.
(shifted) in the tool post
Wind the cutting tool out of the groove and move the
– the tool has been removed and re-sharpened
carriage to the right to clear the end of the workpiece by
– the workpiece has to be reset. reversing the lathe.
Listed below are the steps to be followed in resetting the Advance the tool by rotating the cross-slide hand wheel,
cutting tool. and bring it to zero position.
Check that the lathe is correctly set up for cutting the Start the machine to allow the tool to grace the thread
thread of the required pitch. groove formed previously to confirm the setting is proper.
With the cutting tool mounted, but cleared off the workpiece, If found satisfactory, take successive cuts to finish the
start the lathe and engage the lead screw with the carriage thread.
half nut.

70 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.95


Capital Goods & Manufacturing Exercise 2.3.96
Machinist - Advanced Turning

Perform eccentric turning with an accuracy ±0.02mm


Objectives: At the end of this exercise you shall be able to
• mark eccentricity
• set the job for eccentric turning in a 4-jaw chuck and turn
• methods of turning eccentric jobs
• uses of eccentric job.

Job Sequence
• Check the raw material • Punch both centre lines.

• Hold the job with about 30mm projection from the • Draw a guide circle 22mm with the eccentric centre
jaw face and true the work piece. as the centre point.

• Face the work piece with minimum stock removal. • Punch the intersecting 4 points.

• Turn ø40mm to a maximum length. • Hold the job in a 4 jaw independent chuck on the turn
diameter by keeping 30mm outside the chuck.
• Reverse the job hold and true it and face the end to
maintain a total length of 50mm and remove the job. • True the concentric guide circle.

• Mark the centre line and eccentric centre line • Turn eccentric diameter 22mm to length of 25mm.
according to the drawing with the help of making
tools.

71
Skill Sequence
Use of marking vernier height gauge and ‘V’ block
Objective: This shall help you to
• mark concentric and eccentric centre lines of a job using vernier height gauge.

Concentricity maximum readings of the dial test indictor is called 'throw'


(i.e.) throw = E. (Fig.2)
When different diameters are turned in the same axis, it is
said to be concentric turning. Figure 1 shows the two
diameters A&B lie on the same axis having the same centre
of rotation. If such jobs are tested with a dial test indicator
and 'V' block, the dial test indicator shows a constant
reading.

Method of identifying eccentricity


The eccentricity of a turned job is tested with the help of a
dial test indictor. It is possible to test the offset of the
Eccentricity turned job when the job is being held on a 4 jaw chuck.
When different diameters are turned on different axes, it is Figures 3 shows the method of using the dial test indicator
said to be eccentric turning. The figure shows that the for testing the trueness. If the diameters are eccentric,
diameter A&B lie on different centres and have a different the dial test indicator gives different readings which amount
centre of rotations. The distance E between the centre of to '2E'. Thus, eccentricity 'E' may be obtained from the
rotation is the amount of 'offset' or 'eccentricity'. If the two readings. (Fig.3)
diameter 'A' is tested with the dial test indicator by
supporting the diameter 'B' in the 'V' block, the dial test
indicator reads twice the reading of 'E'. The different in the

72 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.96


the eccentric turning. With the help of this circle, the 'Offset'
may be easily made by using a surface gauge. Thus the
eccentric axis is located for external eccentric turning and
eccentric boring. (Fig.4)

The other method of testing eccentricity is using a 'V' Block


and dial test indicator. In this method, one of the diameters
of the eccentric turning is supported in the 'V' block and
the reading of the other diameter is obtained with the help
of the dial test indicator. The difference in the readings
gives the throw '2E'. Thus eccentricity 'E' may be
determined by this method.
Eccentric turning by using a lathe carrier and centres is
Method of eccentric turning done with the help of accurate marking. Before using these
External eccentric turning as well as internal eccentric accessories, the 'offset' has to be marked with the help of
boring may be accurately carried out on a centre lathe. marking tools. Bothe the concentric and the offset centres
The figure shows the external eccentric and internal have to be centre-drilled. By using these centre holes, it
eccentric jobs. is possible to turn eccentric turning on the job.

It is possible to turn the eccentric turning with the help of Use of eccentric turned jobs
a 4 jaw chuck as well as using a lathe carrier and centres, Eccentric turned jobs are largely used in automobile
holding the work between centres. industry to convert rotary motion into reciprocating motion.
When a 4 jaw chuck is used, a guide circle of the eccentric An eccentric - turned job is used in crankshafts. It is used
axis is essential for truing the eccentric axis. This in power press, guillotine machines, and press brakes. It
requirement may be met by the marking process prior to is also generally used in automatic controls.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.3.96 73


Capital Goods & Manufacturing Exercise 2.4.97
Machinist - Grinding

Identification of different types of grinding machines


Objectives: At the end of this exercise you shall be able to
• identify the different types of grinding machine
• state the use according to the purpose of grinding operation.

74
Job Sequence
Instructor should arrange to visit the difference • Record it in table -1
types of grinding machines available in the ITI • Get it checked by the instructor.

• Trainees will note down the types of grinding machines


in the ITI.
Table 1

No. Name of the machines Remarks

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.97 75


Capital Goods & Manufacturing Exercise 2.4.98
Machinist - Grinding

Wheel balancing & truing


Objectives: At the end of this exercise you shall be able to
• truing the grinding wheel
• balancing the grinding wheel.
TASK 1: True the grinding wheel
• Start the wheel head and allow it to run, for the machine
• Clean the grinding machine table to attain normal working temperature.
• Select and hold the dresser in proper holder • Dress the wheel on the periphery (Fig.2)
• Mount the holder with dresser in grinding machine table
(Fig.1)

Dress the sides if the wheel diameter exceeds


250mm. Apply a small in feed of the diamond
until eccentricity of the wheel is removed.
• Stop the machine.

TASK 2: Balancing a grinding wheel


Mount the Wheel on the machine. Use both hands when removing the wheel
assembly. Take care not to knock on any
Remove the balance weight. (Fig 3)
machine part to prevent any damage to the
wheel.
Preparing the balancing unit
Lower the protection guards
Place the levelling plate on the balancing stand. (Fig 4)
Adjust the unit, using two knurled Screws on the base
until the bubble in the levelling plate is concentric with the
circle engraved on the glass.

Clean the internal and external cones


Place the wheel unit on the spindle nose, and tighten the
lock-nut
Replace the Wheel guard
Remove the Wheel guard and lock-nut
Screw on the collet Extractor and remove the wheel
assembly.
76
Positioning Wheel on unit
Clean the bore of the unit (Fig.5) and the balancing
Mandrel, then mount the Wheel assembly on the mandrel.
(Fig.6)

If the wheel finds the heavy points quickly, the


balancing weights could be moved
approximately 180o. (This indicates that the
wheel is considerably out of balance). Move
the weights equally towards the lighter side,
approximately 3 mm at a time. Fig 8)

Repeat until the assembly remains static in any position.


Tighten the nut on the mandrel. (Fig.7a) Remount the assembly on the wheel head, replace the
Raise the protection guards.(Fig.7b) guard and re-dresss the wheel before putting it into further
operation.
Place the wheel to be balanced on the top of the protection
slides and lower gently on to the balancing stand.(Fig.7c)
(ii) Balancing the wheel
Visually ensure that the balancing mandrel is at right angles
to balancing ways. (Fig 8a)
Allow the wheel to revolve slowly, by its own momentum
until stationary.
Place a chalk mark at the bottom to indicate a heavy
point. (Fig 8b)
Turn the wheel 90° to the heavy point, and diametrically
opposite. (Fig 8c&d)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.98 77


Capital Goods & Manufacturing Exercise 2.4.99
Machinist - Grinding

Dressing of grinding wheel


Objectives: At the end of this exercise you shall be able to
• set the grinding wheel
• mount the holder with dresser.
This operation is done after mounting the grinding wheel for
removing any high spots on the face of the wheel with a
diamond dresser. (Fig 1).

Dressing grinding wheel by grinding head dresser


• Start the motors for the grinding spindle and coolant.
• Open the cover of the grinding wheel, and shift the
The high spots are removed for uniform contact of the wheel dresser to the centre of the grinding wheel as shown in
over the job. Otherwise only the high spots on the wheel will Fig 2 by pulling the dresser feed lever to the front side.
contact the surface resulting in poor surface finish.
• Turn the dresser cut in dial gently to let the dresser tip
Dressing is the operation of removing dull grains and metal touch the perimeter of the grinding wheel.
particles from the cutting surface of a grinding wheel. This
operation exposes sharp cutting edges of the abrasive • Restore the dresser feed lever to the original position
grains to make the wheel cut better. and shut the cover of the grinding wheel.
They are two method of dressing a grinding wheel for the • Set the depth of cut in the dresser by means of the
surface grinder. dresser dial and carry out the dressing by operating the
dresser feed lever. (The depth of cut for dressing is
• Dressing of grinding wheel by grinding head dresser. 0.015-0.025mm at a time, and the dresser feed speed
(Fig.2) is 250-500mm/min in case of the finish).
Dressing of grinding wheel by dresser attached to
holder
Keep the dresser on the base as shown in Fig.4. This
position helps to prevent chattering and the tendency to
drag in during the dressing operation.

• Dressing of grinding wheel by attached to holder. (Fig.3)

78
Clean the magnetic chuck thoroughly with a cloth and then
(Fig 5) feel for any dirt with your palm. Remove it if any.

Place the diamond on the last two magnetic poles on the


left hand end of the magnetic chuck Paper should be Take a finish pass with 0.01mm across the face of the
placed between the diamond holder and the chuck is grinding wheel. (Fig 8&9)
prevent scratching the chuck surface when removing the
diamond holder. (Fig.6)

The point of the diamond should be offset about 12mm from


the grinding wheel centre line with reference to the direction
of rotation of grinding wheel (Fig.6)
Make sure that the diamond clears the wheel, then start the
grinder.
Lower the wheel until it touches the diamond.
Move the diamond slowly across the face of the wheel
(Fig.7)
Take light cuts (0.02mm) until the wheel is clean, sharp and
is running true.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.99 79


Capital Goods & Manufacturing Exercise 2.4.100
Machinist - Grinding

Grinding of block (six sides) by surface grinding machine with an accuracy


of +/- 0.01mm
Objectives: At the end of this exercise you shall be able to
• grind parallel surface to an accuracy +/-0.01
• prepare the surface grinding machine for grinding operation.

Job Sequence
• Machine the jobs and determine the grinding • Mount the job on the magnetic chuck keeping down
allowance for each surface to be ground. the surfaces already ground and rough grind the
opposite surfaces of 20.03mm thick.
• Prepare the surface grinding machine for grinding.
• Finish grind and bring the thickness to 20.00 to an
• Rough grind both the opposite sides of the pieces
accuracy of ± 0.01mm.
and maintain to 15.04mm thick.
• Remove the parallels from the magnetic chuck.
• Dress the wheel for finish grinding.
• Clean thoroughly and deburr with a fine abrasive
• Finish grind the pieces 15.00 thick to an accuracy
stone.
of ±0.01mm. Measure the size with a 0-25 outside
micrometer. • Measure the width and thickness for dimensional
accuracy with an outside micrometer.
• Set the job with the angle plate (150x150) by 2 ‘C’
clamps of 100mm size for grinding adjacent surfaces • Also check for parallelism with an outside
at 90o. micrometer on the four corners on each piece.
• Rough grind the adjacent sides individually leaving • Demagnetize the block.
half of the grinding allowance for the opposite surfaces
to 20.03mm thick.

80
Skill Sequence
Grinding parallel surfaces
Objective: This shall help you to
• grind parallel surfaces to an accuracy of ± 0.01.

Always assume that the workpiece is distorted in one or


more planes. (Fig 1) For this reason a true reference face
must first be produced.

Clean the abrasive particles spread over the magnetic


chuck and table.
Mount the workpiece on the magnetic chuck, (Fig 5)
Check the flatness with a straight edge and locate the resting the lengthier surface with the side stopper plate of
lowest spot by visual examination. the magnetic chuck.
Check the parallelism using an outside micrometer and
mark the high spot. (Fig 2)

Set the table traverse-stopper dog considering the (Fig 6)


Clean the work table surface and the bottom of the approach length and over travel. Also set for the clearance
magnetic chuck. (Fig 3) of the job width.

Set the feed rate of the table to 10 to 15 m/mm.


Hand-feed the wheel head down, and watch the narrowing
of the gap. Stop at 0.25 mm gap approximately.
Place, align and clamp securely the magnetic chuck over
Clear the job from the grinding wheel.
the work table.
Switch on the grinding wheel spindle.
Dress the grinding wheel for rough grinding. (Fig 4) (Seek
the help of your instructor) Engage the longitudinal power traverse using the fine feed
mechanism and 'pick up spark' at the high spot.
Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.100 81
Cross-traverse the workpiece to clear the wheel. Check the ground face with a straight edge and the
thickness with an outside micrometer. This will be the
Start the coolant pump and direct the stream of the coolant
reference surface for grinding the other surfaces.
between the wheel and the workpiece. (Fig 7)
Dress the grinding wheel for rough grinding.
Clean the magnetic chuck face and mount the ground
surface of the workpiece over the face of the magnetic
chuck. (Fig 9)

This will reduce the heat of the job, and the ground particles
will be washed away.
Apply a 0.03 mm depth of cut by the fine feed mechanism
when the workpiece clears the grinding wheel after each
cut. (Fig 8)
Set table traverse stops.
Clean up the face by removing minimum material.
Remove the workpiece, deburr and clean it.
Determine the stock of material to be removed with an
outside micrometer.
Check parallelism with an outside micrometer and determine
the amount of taper if any. (To correct taper ask your
instructor for advice)
Keep your hands away from the revolving
wheel at all times to avoid injuries to yourself. Remount the workpiece in the same position and continue
rough grinding, leaving an allowance of 0.012 mm for finish
Repeat rough grinding till the grinding allowance for that
grinding.
side is ground away.
Remove the workpiece and dress the wheel for finish
Cross-traverse the workpiece to clear the wheel.
grinding.
Re-dress the grinding wheel for finish grinding. (Seek the
Remount the workpiece and give a depth of cut of 0.005
help of your instructor). Clean the table and workpiece
mm and grind the surface.
thoroughly.
Remove the workpiece from the magnetic chuck.
Engage the longitudinal travel feed.
Thoroughly clean the workpiece and the surface of the
Apply 0.012 mm cut and finish grind the workpiece allowing
chuck.
the wheel to 'spark out'.
Measure the thickness and parallelism and decide the
Always apply the depth of cut at the end of the
remaining allowance.
stroke.
Remount the workpiece and apply another 0.005 mm depth
Stop all traverses and turn off the coolant. Position the
of cut and finish grind.
workpiece away from the wheel.
Using the graduated dial of the wheel head, down feed for
Remove the workpiece from the magnetic chuck. While so
grinding the remaining allowance.
doing see that no scratches are formed on the magnetic
chuck. (Consult your instructor) Allow the wheel to spark out.
Remove the sharp edges of the workpiece by using a fine Remove the workpiece and clean thoroughly. Check the
abrasive stick or stone. thickness, parallelism and flatness of the surface texture.

82 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.100


Preparing surface grinding machine for grinding
Objective: This shall help you to
• prepare the surface grinding machine for grinding operations.
Preparing wheel spindle
It is very essential to check the different controls of the
machine before actually starting the grinding operation.
This will help the preparation of the machine for work.
Check the following before the grinding operation.
Checking and oiling before start
Supply oil to all the lubricating points.(Consult your
instructor)
Check that the button on the operation board is at the stop
position. (Fig 1)

Check that the clutch of the table traverse feed handle is


cut.
Check that the table dog is fixed.
Manual feed of table
Turn the grinding wheel elevation handle anticlockwise to
Set the table reverse lever at the neutral position (Fig.1) lower the grinding wheel. (Fig 1)
Engage the clutch of the table traverse feed handle.
Turn the grinding wheel elevation handle clockwise to raise
Move the table to the right and left by turning the handle the grinding wheel.
clockwise and anticlockwise respectively.
Hydraulic operation of table
Manual and automatic feed of saddle
Pull the table traverse feed handle to the front side to
Move the saddle forward by turning the saddle cross-feed disengage the clutch.
handle clockwise. (Fig 1)
Push the hydraulic driving push-button to drive the table
Move the saddle backward by turning the saddle cross- hydraulically. (Fig 1)
feed handle anticlockwise.
Adjust the table speed by the use of the table speed
Set in the automatic feed by turning the saddle feed change adjusting lever. (When the lever is pushed up, the table
lever upward and downward. (Fig 2) (when the lever is speed is increased. The speed is decreased by lowering
pushed up or down, the saddle moves forward or backward the lever and the hydraulic drive is stopped at the lowest
respectively) position of the lever)
Raise and lower the grinding wheel. Stop the hydraulic drive by pushing or pulling the hydraulic
Disengage the fine feed knob. (Fig 3) drive stop lever. (The table is stopped at the right end
position)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.100 83


Capital Goods & Manufacturing Exercise 2.4.101
Machinist - Grinding

Grinding of step block by surface grinding machine with an accuracy ±


0.01mm
Objectives: At the end of this exercise you shall be able to
• mount the grinding wheel
• set the job on the magnetic chuck
• align the job on the magnetic chuck using dial test indicator
• grind stepped surfaces flat and square
• check the dimensions by an out side micro meter.

84
Job Sequence
• Study the job drawing, measure the job and determine • Ensure that the surface (c) is 1 to 2 mm above the top
the grinding allowance on each surface and step to be surface of the angle plate.
ground. (Fig 1)
• Do not seat the job tight on the parallel, after aligning
Fig 1 with the try square.
1
• Rough and finish grind the surface ‘C’ removing half of
the grinding allowance.
• Repeat the above steps for grinding the surface (d).
• Rough and finish grind the surface (d) removing half of
the grinding allowance.
• Mount the surface (C) on a magnetic chuck,and align
1
the surface (d) against the stopper plate. (Fig 3)

• Prepare the machine, the magnetic chuck and grinding


wheel for the surface grinding operation.
• Rough and finish grind the surfaces (a) and (b) to parallel
and maintain the size to 39 ± 0.02 mm removing half of
the grinding allowance.

MAN24101H3
• Set the job on the angle plate (150 x 100 mm) with a
100 mm ‘C’ as shown in Fig 2.
• Rough and finish grind the step (e) to 14.50 mm. Check
with a depth micrometer.
• Rough and finish grind the step (f) to 29.50 ((f) - (e) =
15.00). Check with a depth micrometer.
• Rough and finish grind the step (g) to 44.50, (g) - (f) =
15.00). Check with a depth micrometer.
• Rough and finish grind the surface (h) to 59 ± 0.02 (h)
- (g) = 15.00). Check with depth micrometer.
• Mount the surface (d) on a magnetic chuck,and align
the surface (c) against the stopper plate. (Fig 2)
• Rough and finish grind steps (i) to (2) to the dimensions
as per the dimensions given in the drawing.
MAN24101H2

• Check the steps with a depth micrometer at every


stage.
• Deburr all the edges.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.101 85


Capital Goods & Manufacturing Exercise 2.4.102
Machinist - Grinding

Grinding of slot block surface grinding machine with an accuracy of ±


0.01mm
Objectives: At the end of this exercise you shall be able to
• grind the slot to an accuracy of ± 0.01 mm
• mount the job on magnetic chuck.

86
Job Sequence
• Perpare the machine and dress the grinding wheel for • Rough and finish grind the top surfaces of the slot to
grinding parallel surfaces. maintain the length to 54.00mm.
• Mount the job on the magnetic chuck. Rough and finish • Measure the bottom of the slot with a depth micrometer
grind the surfaces parallel, to maintain the thickness and decide the grinding allowance.
to 9.5mm. • Rough and finish grind the bottom of the slot to maintain
• Deburr the edges. the depth to 29.00mm using face of the grinding wheel.
Check the depth with a depth with a depth micrometer.
• Rough and finish grind the width to 54mm using an
angle plate and ‘C’ clamps with suitable parallels. • Rough and finish grind the shoulder to 8.50mm using
the rear side of the grinding wheel.
• In the same setting, rough and finish grind the
54x9.5mm surface at 90° and remove half of the grinding • Grind only half of the grinding allowance.
allowance on the length of 54 mm. • Check the size, 8.5mm, with an outside micrometer.
• Dress the grinding wheel for the grinding slot. • Rough and finish grind the other shoulder until the width
• Mount the plain vice on the magnetic chuck and align of the slot becomes 31.00.
its fixed jaw parallel to the grinding wheel axis. • Check the slot for its centricity with an outside
• Hold the job in the vice such that the bottom of the slot micrometer and the width by a snap gauge, (Consult
is 2mm above the top surface of the vice jaws. your instructor)
• Remove the job, deburr the edges, and demagnetize.

Skill sequence
Grinding a slot to an accuracy of ±0.01mm
Objective: This shall help you to
• grind a slot to an accuracy of ±0.01mm.

Select and mount the grinding wheel such that the face
width of the wheel is less than the width of the slot to be
ground.(Fig 1)

Dress the wheel for the faces, clean up and relieve both
sides of the wheel if a straight wheel is used.
Mount the workpiece on to the magnetic chuck directly if
it is of a sufficiently large size.
If the job is small in nature, take the support of an angle
plate.
Align the workpiece accurately in the correct plane and
secure. (Fig 2) (Consult your instructor)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.102 87


Set the table traverse stops in position. Keep the wheel away from the slot.
Position the wheel approximately 0.4mm above the Position the wheel and touch the other vertical face of the
horizontal face of the slot and switch on the wheel. job with the wheel. (Fig 5)
Engage the table traverse and feed wheel in until it just
touches the horizontal surface.
Keep the wheel clear of the vertical faces.
Clean up the whole horizontal surface by the table traverse
and careful cross-feed operation. (Consult your instructor)
Stop the wheel and clear it from the work and determine
the amount of material to be removed.
Reposition the wheel into the slot, start up the wheel and
engage the traverse.
Feed in the wheel and grind the whole surface with 0.04mm
accuracy.
Keep the wheel clear of the horizontal face.
Keep the wheel away from the job and set the depth of
Determine the material to be removed on the vertical faces.
cut.
Position the wheel and touch the vertical face of the job
Down-feed the wheel and grind the vertical face down up
with the wheel. (Fig 3)
to the space corner. (Fig 6)
Stop the job away from the grinding wheel.
Deburr and clear the ground surfaces.
Check the slot for its dimension with a vernier caliper and
depth micrometer.

Keep the wheel away from the job.


Set the depth of cut.
Feed the Wheel down and grind the vertical face down up
to the corner (recessed). (Fig 4)

88 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.102


Capital Goods & Manufacturing Exercise 2.4.103
Machinist - Grinding

Set and perform angular grinding using universal vice/sine vice to standard
angle
Objectives: At the end of this exercise you shall be able to
• mount the grinding wheel
• set the universal vice on the magnetic chuck
• hold the job & grind the angular surface.

Job Sequence
• Study the drawing. Observe the surface to be ground
and determine the grinding allowance for each surface
by measuring.
• Prepare the machine dress the grinding wheel for
grinding angular surface.
• Mount the suitable universal vice on the magnetic
chuck and align its fixed jaw parallel to the grinding
wheel axis by using the dial test indicator.
• Ensure that all the swivel base graduations coincide
with the O degree dead mark before aligning
• Hold the job in the vice and tilt the vice to 45° (Fig1) • Remove the same amount of material from the surface
(b) using the front side of the grinding wheel by manual
• Rough and finish grind the surface, (a) using the face cross-feeding in the same setting.
of the grinding wheel. Record the amount of materials
removed by noting down the divisions on the graduated • Remove the job. Deburr and demagnetise the job.
dial of the wheel head.

89
Skill Sequence
Grinding angular surface using universal vice
Objective: This shall help you to
• grind angular surfaces using a universal vice.

Dress the grinding wheel on the sides for relief and on the Clean the job and measure it to determine the grinding
face for trueness. (Fig 1) allowance. (Ask your instructor for help in determining the
allowance)
Hold the job in the vice such that the horizontal surface to
be ground is aligned parallel to the surface of the table
using a dial test indicator. (Fig 4)

Clean the machine table and mount the universal vice.


Align the fixed jaws of the vice perpendicular to the axis of
the spindle. (Fig 2)

Position the stop dogs for longitudinal traverse.


Start the wheel and lower the wheel head until the wheel
just sparks the high spot of the job.
Start the table travelling automatically and feed the entire
length of the job and clear off the job from the wheel.
Engage the vertical depth for rough and finish cut as
predetermined, and feed from the cross-feed manually.
(Fig 5a)
Grind the longitudinal surface up to the corner relief.
Ensure that the swivel base graduation coincides with ‘O’
degree dead mark before aligning. Remove only that much of material pre-determined as
grinding allowance, and record the amount of material
Tilt the vice to 45o with reference to the graduated plate at removed.
the bottom of the vice. (Fig 3)
Raise the wheel head to 0.20mm and without releasing
the wheel, plunge the wheel little by little against the
vertical surface of the job to be ground to the depth equal
to the horizontal surface.
Raise the wheel gradually to finish grind the vertical surface.
(Fig 5b)

90 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.103


Capital Goods & Manufacturing Exercise 2.4.104
Machinist - Grinding

Make slide fit with an accuracy ± 0.01mm (Male & Female)


Objectives: At the end of this exercise you shall be able to
• set the grinding wheel
• mount the job
• grind the male & female part as per drawing with an accuracy of ± 0.01.

91
Job Sequence
TASK 1: Male part grinding
• Clean the work piece • Set and align the work piece
• Check the work piece to determine the grinding • Start the machine and touch down the wheel and
allowance then finish grind the job
• Select the machine tool and dress the grinding wheel • Stop the machine
• Clean the machine table • Remove the job and check measurement by
measuring instrument
• Set the magnetic chuck and align by using Dial
Test Indicator

TASK 2: Female part grinding


• Clean the work piece • Start the machine and touch down the wheel and
• Check the work piece to determine grinding then finish grind the job
allowance • Stop the machine
• Select the suitable grinding wheel and dress the • Check matting part (slide level)
grinding wheel
• Remove the job and clean the job
• Clean the machine table
• Measure and check the dimension
• Clean the magnetic chuck
• Matting and slide the job.
• Set and align the work piece

Skill Sequence
Grinding a slot to an accuracy of ± 0.01 mm
Objective: This shall help you to
• grind a slot to an accuracy of ± 0.01 mm.

Select and mount the grinding wheel such that the face Align the workpiece accurately in the correct plane and
width of the wheel is less than the width of the slot to be secure. (Fig.2) (Consult your instructor)
ground (Fig.1)
Set the table traverse stops in position.
Position the wheel approximately 0.4mm above the
horizontal face of the slot and switch on the wheel.
Engage the table traverse and feed the wheel in, until it
just touches the horizontal surface.
Keep the wheel clear of the vertical faces.
Clean up the whole horizontal surface by the table traverse
and careful cross-feed operation. (consult your instructor)
Stop the wheel and clear it from the work and determine
the amount of material to be removed.
Reposition the wheel into the slot, start up the wheel and
engage the traverse.
Feed in the wheel and grind the whole surface with 0.04mm
Dress the wheel on the faces, clean up and relieve both accuracy.
sides of the wheel if a straight wheel is used.
Keep the wheel clear of the horizontal face.
Mount the workpiece on the magnetic chuck directly if it
is sufficiently large size. Determine the material to be removed on the vertical faces.

If the job is small in nature, take the support of an angle Position the wheel and touch the vertical face of the job
plate. with the wheel. (Fig. 3)

92 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.104


Keep the wheel away from the job and set the depth of
cut.
Down-feed the wheel and grind the vertical face down to
the corner. (Fig. 6)
Stop the job away from the grinding wheel.
Deburr and clear the ground surfaces.
Check the slot for its dimension with a vernier caliper and
depth micrometer.

Keep the wheel away from the job.


Set the depth cut.
Feed the wheel down and grind the vertical face down up
to the corner (recessed). (Fig. 4)
Keep the wheel away from the slot.
Position the wheel and touch the other vertical face of the
job with the wheel. (Fig. 5)

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.104 93


Capital Goods & Manufacturing Exercise 2.4.105
Machinist - Grinding

Perform form grinding


Objectives: At the end of this exercise you shall be able to
• select and set the grinding wheel
• mount the job on magnetic chuck
• grind the concave surface.

Job Sequence
TASK 1
Concave surface grinding • Stop the machine and check the measurement.
• Clean the work piece. • Set the radius attachment on magnetic chuck and
form the wheel in according to radius.
• Check the work piece to determine grinding allowance.
• Remove the attachment after completing the job.
• Select the machine tool and dress the grinding wheel.
• Set the job and align with form wheel.
• Clean the machine table and magnetic chuck.
• Finish the form grinding to required depth.
• Set the magnetic chuck and align by using Dial Test
Indicator. • Stop the machine and check machine by radius
gauge.
• Set and align the work piece.
• Clean the job.
• Start the machine and touch down the wheel and then
finish grind the job.

94
Capital Goods & Manufacturing Exercise 2.4.106
Machinist - Grinding

Make dovetail fitting with an accuracy ± 0.01mm (Male & Female)


Objectives: At the end of this exercise you shall be able to
• select and set the grinding wheel
• mount the job on magnetic chuck.

95
Job Sequence
TASK 1: Grinding male part
• Prepare the job in milling as per drawing leaving the • Fix press the wheel to 30° on the spindle.
grinding allowance.
• Grind the dovetail 60° on both side.
• Fix the vice on table of surface grinder.
• Check the dimension and angles with the use of
• Set the job on vice using parallel block. vernier caliper and vernier bevel protractor.
• Remove the job and deburr.
TASK 2: Female part
• Make the female dovetail on milling machine. • Finish dovetail surface using fine oil stone.
• Match the job with the male part.

Job Sequence
TASK 1: Grinding female part

• Prepare the job in milling as per drawing leaving the • Dress the grinding wheel in required shape.
grinding allowance. • Set the job on vice using parallel block.
• Study the drawing and ascertain the surface to be • Grind the dovetail 60° on both side.
ground.
• Check the depth with a depth micrometer.
• Fix the vice on the table of vertical surface grinder.
• Remove the job deburr all the edges with a fine
abrasive stone.
TASK 2: Male part

• Prepare the job in milling as per drawing leaving the


grinding allowance.
• Study the drawing and as certain the surface to be
ground.
• Fix the vice on the table in vertical surface grinder.
• Dress the grinding wheel in required shape.
• Set the job on vice using parallel block.
• Grind the dovetail 60o on both
• Check the depth with a depth micrometer.
• Remove the job deburr all the edges with a fine
abrasive stone.

96 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.106


Capital Goods & Manufacturing Exercise 2.4.107
Machinist - Grinding

External parallel cylindrical grinding (Both holding in chuck/collet and


inbetween centres)
Objectives: At the end of this exercise you shall be able to
• select and set the grinding wheel
• mount the job
• check the parallelism with dial test indicator.

97
Job Sequence
• Prepare the cylindrical grinding machine for operation. • Take a moderate cut (0.04mm) measure the workpiece
diameter and the work is parallel after the first traverse.
• Study the drawing and measure the grinding allowance
for given job. • Continue traverse and give depth of cut at the end of
each traverse until the job is within 0.05-0.10mm of the
• Dress the grinding wheel make sure that the abrasive
required final size.
particles are removed uniformly.
• Reserve the position of the job in the centres.
• Mount the job in between centres.
Use a soft metal spacer to protect the job.
• Set the length of stroke using reversing dogs.
• Grind the end of the job previously covered by the carrier
Fix the safety guard in proper place.
to the same size as the other end of the job.
• Put on the grinding wheel.
• Dress the grinding wheel.
• Start the work table traverse.
• Grind the work piece to the finished size Ø25mm like
• Bring the grinding wheel forward to engage the roughing cycle.
workpiece by operating the cross feed hand wheel on
• Remove the job from centres.
the machine.
• Remove burrs of the job using fine abrasive stone.
Wear goggles at all times while using a
grinding machine. • Measure the diameter of the job used by 0-25mm
outside micrometer.
• Check the cylindrical of the job.
Skill Sequence
Cylindrical grinding
Objectives: At the end of this exercise you shall be able to
• cylindrical grinding
• checking of parallelism
• measurement by micrometer.

Prepare the cylindrical grinding machine for grinding


Throughly clean the machine with banian cloth.
Don’t use cotton waste for cleaning the
grinding machine.

Check the oil level in the workhead and wheel head (Fig.1)

Start the hydraulic motor by pressing the hydraulic motor


switch (Fig 3)

If it is below the recommended oil level inform to the


instructor. (Fig 2)
Apply oil in all oil points use oil gun.
(IOC SAE 30/40)
Apply grease in all grease points with grease gun (servo
gem No.2)
Ensure that the work head and wheel head are set to zero
position.
Check the wheel guards are in proper position. Check the oil pressure gauge.
Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.107
98
Start the grinding wheel and check the direction of rotation. Check the dial reading at zero so that the work head centre
(Fig 4) by viewing the direction of arrow provided on the and tail stock centre at same line.
wheel guard.
The table at zero degree aligning is correct position.
Set the job in between centres
Select a dog corresponding to the work diameter.
Fit a dog at right angles to the end of the work. (Fig 7)

Workhead
Start the work head spindle by pressing the work head
motor switch. (Fig 5)

Check for the job rotation.


Align the work table perpendicular to the wheel head
Clean the wheel head of front side. Too long bolt on a dog may become loose in the course of
Hold the dial test indicator with magnetic base on wheel grinding.
head slide. (Fig 6) Hold the work securely in both hands and fit the centre
hole carefully to the centre on the work head side. (Fig.8)

Fix the test bar in between centres.


Set the work head wheel head and table at zero degree.
Touch the dial on job and giving light pressure as shown in
figures.
Move the table from work head to tailstock.
Check the dial reading zero.
Incase variation of reading ±10 divisions.
Loose the table top Allen screws and adjust slightly side
screw.
Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.107 99
Hold the work with the left hand as illustrated while holding
the work to prevent the centre hole coming out.
As illustrated support the work with the left hand and fit
the centre to the centre hole by operating the lever of the
tailstock with the right hand. (Fig.9)

So the workpiece mounted in between centres. (Fig 11)


Adjustment of taper
Before support the job in between tailstock When the work has been tapered beyond expectation
centre gap is 5mm should be maintained. loosen the four fasteners. Allen screw of the upper table,
(Fig.9) set the dial gauge at zero and then a mind the swivelling
Where the tailstock centre has a nut for adjusting nut so of the table with the adjusting screw as illustrated. (Fig.12)
as to allow the work to be turned lightly by the fingers. When the diameter at the side of the work head is larger
Where the tailstock centre has a nut for adjusting nut so than the other turn the table clockwise and when the
as to allow the work to be turned lightly pin in accordance diameter at the tailstock side is too large turn in counter
with the dog with the dog leg length. (Fig 10) clockwise.

100 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.107
As for table tilting give the specified conversion value to Move the dial traversely.
the dial gauge according to the length and the difference
Check the reading for variation.
in size of the work. (Fig 12)
Incase of variation on job go for regrinding.
Recheck the job for parallelism.
Rotate the job by hand and check for cylindrical.
If the error is repeated and it is within the permissible limit
then the same may be accepted as finished job.
Holding the micrometer for measurement
The micrometer may be held either in one hand or both
the hands.
Holding in one hand (Fig 14)
Hold the outside micrometer in your right hand, keeping
the graduations on the main scale towards you.
Fix the upper table do trial grinding to repeat adjustments
for obtaining the given taper.
When the given taper has been obtained, do rough grinding
leaving a finish margin of 0.02 -0.05mm in the outer
diameter.
To finish grind
Determine the numbers of work revolution so as to make
the peripheral speed of the work 12-15m/min.
Adjust the table speed so as to be fed at about (1/8-1 10)
of the wheel thickness per work revolution.
If necessary do finish dressing.
Make the depth of cut from 0.0025mm to 0.01mm per
stroke, while measuring from time to time as grinding by
making the depth of cut by graduations. Support the frame on the lower centre of your palm. Use
In the final stages the depth of the cut shall not be made, your little or third finger to hold the frame in the palm.
but reciprocate the table 2-3 times to do spark out. Palm the middle finger behind the frame to support it.
Back the wheel spindle stock and do fine chamfering with Keep the first finger thumb free to adjust the knurled
an oil-stone. thimble.
Measure the size of the work when it stops fully. Holding by both the hands. (Fig 15)
Parallelism checking ref. (Fig 13) Sometimes, it may be more convenient to hold the
Clean the surface plate without any dust and oil. micrometer with both the hands.
Fix the tailstock centres on surface plate.

Hold the dial in magnetic base.


Keep it on the surface plate.
Hold the job in between centres.
Touch the job and give the pressure on the dial and set
zero.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.107 101
Support the frame between the fingers and the thumb of
your left hand .
Use the thumb finger of your right hand to adjust the
thimble.
Set the micrometer on the workpiece for measurements.
High skill is needed for obtaining accurate measurement
with the outside micrometer. A wrong setting of the
micrometer over the workpiece may cause
- inaccurate reading
- excessive strain on the screw thread
- distortion in the frame.
Fig.15 shown the adjustment of the spindle and anvil over
the workpiece. As you adjust the workpiece between the
Read the measurement.
spindle and the anvil you should feel a light pressure or
resistance against the workpiece surface. Use the spring- Method of reading the micrometer 0-25 range.
loaded ratchet stop to ascertain the feel. (Fig 16)
Look at the reading the which has been taken from the
workpiece.
Read on the barrel scale the number of whole millimetres
that are completely visible from the bevel edge of the
thimble.Fig 19a shows 4 divisions = 4mm.
Add any half millimetres that are completely visible from
the bevel edge of the thimble. (Fig 19a)
Fig (19b) shows 1 division =0.5mm.
Add the thimble reading to the main scale reading which
has already been taken. Fig 19c shows the 5 th division of
the thimble scale is coinciding with the index line. So
thimble reading =5x0.01=0.05mm. (Fig 19c)

Measuring outside diameter using outside micrometer


While using only one hand.
Close the anvil and spindle until you feel them just
touching the work.
Move the work slightly between the spindle and the anvil
or pass the micrometer over the workpiece by moving your
wrist. (Fig 17)

Make further adjustments of the thimble as required until


you obtain the right ‘Feel’ (Fig 18)
When satisfied with the feel remove the fingers from the
thimble.
Turn the micrometer towards you.

102 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.107
Capital Goods & Manufacturing Exercise 2.4.108
Machinist - Grinding

Plunge Grinding
Objectives: At the end of this exercise you shall be able to
• mount the grinding wheel on the cylindrical grinding machine
• hold the job between centres in eccentric position
• grind the job to the required dimension and accuracy.

Job Sequence
• Clean the machine completely. • Set the longitudinal position and tighten the
longitudinal traverse.
• Determine the grinding allowance.
• Start the grinding wheel and the job rotation.
• Select the suitable grinding wheel.
• Work rotates in a fixed position as the wheel feeds.
• Balance the grinding wheel.
• Grind the job to an accuracy of 0.01mm.
• Mount the wheel on the cylindrical grinding machine.
• Move the wheel away from the job and stop the
• Dress the grinding wheel. movement of the wheel and the job.
• Hold the job between centres. • Check the dimensions with a micrometer.
• And then follow the above procedure for next plunge
grinding operation.

103
Capital Goods & Manufacturing Exercise 2.4.109
Machinist - Grinding

Perform straight bore grinding


Objectives: At the end of this exercise you shall be able to
• mount the internal grinding attachment
• mount the grinding wheel and dress the wheel by diamond dresser
• set the job in four jaw chuck by using dial test indicator
• grind the plain bore with an accuracy of ± 0.04
• measure the bore diameter by using telescopic gauge.

Job Sequence
• Turn the part as per drawing with required grinding • Fit the spindle and mount spindle.
allowance. • Dress the wheel with a diamond tipped dressing tool.
• Prepare the machine for internal grinding. (Fig.1) • Measure the bore diameter of the workpiece to check
the grinding allowance.
• Determine the work and wheel surface speeds and
set the machine accordingly.
• Mount the workpiece in a chuck.
• True the workpiece used by dial test indicator.
• Set the length of stroke using reversing dogs.
Make sure that the traverse setting do not
cause the wheel to contact any internal
shoulder in the workpiece and that the wheel
does not leave the workpiece surface
completely at the end of the traverse strokes.
• Put on your goggles.
• Start the grinding wheel.

104
• Start the head stock spindle drive. The spindle chosen should be as rigid as possible. Where
a long workpiece is to be ground the spindle will be
• Check that the directions of rotation of the wheel and
correspondingly long and thus subject to flexing under
workpiece are opposed.
load. If care is not taken this flexing will cause chatter of
• Grind the Ø 25 x 35mm bore. the wheel with resultant marking of the bore surface. It will
also produce a bore of uneven diameter.
• Start coolant supply and table traverse if necessary.
• Run the grinding wheel to the workpiece by hand and Warning
advance the wheel against the bore taking a light cut. Due to the nature of the operation a wheel
guard is not used during internal grinding
• When cut is complete measure the bore and reset the operations. The workpiece serves as a guard
feed. during actual grinding, but remember that the
• Make repeated cuts until close to the desired size. unguarded wheel is a definite safety hazard
when not within a workpiece. Keep your hands
• Dress the wheel again for finish grinding.
away from the moving wheel and wear close
• Check the bore size, parallism and make the final cuts. fitting clothing. If a guard is available on the
machine to the wheel when not actually
• Remove burred edges.
grinding, make sure this set in place after the
• Measure the base by using telescopic gauge bore. wheel is retracted from the workpiece.
Mounting the spindle (Fig.2)
Set the job in four jaw chuck using dial test indicator.
(Fig. 4)

For setting up the internal grinding spindle of a universal


grinding machine, the general procedure is as follows:
• Position the internal grinding attachment, including the
spindle on the wheel head and fix securely. Refer to
the operators handbook for the particular machine.
• Mount the drive belt between the internal grinding drive
motor and the pulley on the internal grinding attachment • Hold the job in a four jaw chuck.
and adjust to proper tension. • Mount the dial stand on machine table.
• If a machine motor selector control is provided turn it • Fix the dial and touch on the job.
to the 'internal' position.
• Move the dial and rotate the job.
• Disengage the power operated cross - feed.
• Check the trueness of the job with the indicator at
• Replace any guards removed to set the attachment in zero position.
place.
• Incase of difference in reading adjust the jaw and
The dimensions of the workpiece (Fig.3)
rotate the chuck.
• The dial moving at A and B are the same reading at
zero.
Grinding a parallel bore (Figs 5&6)
• Set up the machine for internal grinding
• Fit the spindle and mount the wheel.
• Dress the wheel with a diamond tipped dressing
tool.
• Measure the diameter of the workpiece to check
the grinding allowance.

Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.109 105
• Determine the work and wheel surface speeds and
set the machine accordingly.
• Mount the workpiece in a chuck or other suitable
support on the machine headstock.
• True the workpiece in the head stock and align the
headstock to the work table.
• If table traverse is necessary, adjust the machine
by setting the table reversing dogs.

Caution
Make sure that the traverse settings do not
cause the wheel to contact any internal
shoulder in the workpiece and that the wheel
does not leave the workpiece surface
completely at the end of the traverse strokes.

• Put on your goggles.


• Start the grinding wheel
• Start the headstock spindle drive
• Check that the directions of rotation of the wheel
and workpiece are opposite.
• Start coolant supply and table traverse if necessary.
• Run the grinding wheel to the workpiece by hand
and advance the wheel against the bore, taking a
light cut.

106 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.109
Capital Goods & Manufacturing Exercise 2.4.110
Machinist - Grinding

Perform step bore grinding


Objectives: At the end of this exercise you shall be able to
• set the machine for grinding internal surfaces
• set workpiece and adjustment of table traverse length
• grind the internal bore maintaining concentricity within close limit.

Job Sequence
• Study the drawing, turn the job as per drawing and • Set stoppers to adjust the table traverse length
maintain the size with grinding allowance. accurately.
• Ascertain the grinding allowance. • Rough and finish grind the bore Ø35 H6.
• Mount the quill head and fix the appropriate • Check the finish part by inside micrometer.
grinding wheel. • Rough and finish grind the bore Ø25 H6.
• Mount the workpiece in the 3 jaw chuck. • Check the finish part by inside micrometer.
• Check the concentricity by DTI. • Check the concentricity using DTI.
• Adjust the coolant.

107
Skill Sequence
Grinding a bore and shoulder
Objective: This shall help you to
• grind the bore and shoulder.

General information 12 Check wheel diameter


For this particular requirement two procedures are adopted. The wheel diameter must be of a size that will grind the
Initially the bore is ground to size as covered in previous face flat. In the example shown, the wheel diameter must
chapter, and then a procedure is used to grind the face of not be greater than bore radius plus the central hole
the shoulder. In work of this nature an undercut may not radius, or less than bore radius minus the central hole
be required in the finished workpiece and the undercut radius.
shown in the following illustrations is used purely as an
13 Dress the front face of wheel
aid to the grinding process. (Fig 1)
• Apply slight angular relief.
• Slightly relieve wheel diameter, leaving approximately
3.2 mm and at front.
14 Grind shoulder face
• Start workhead
• Working to the indeed index, position the wheel to
clear the finished bore diameter by approximately 0.02
mm.
• Hand traverse table, to position the wheel inside the
bore and just clear of shoulder face.
The line previously marked upon the spindle will give
indication of distance between wheel and face.
• Traverse table very slowly until sparks or sound
indicate the wheel is grinding the face.
1 Measure workpiece
• With the left hand holding the traverse wheel to act as
Check diameter and depth of bore. a brake, gently tap the handle with the right hand to
2 Mount workpiece advance the workpiece on to the wheel. (Fig 2)

3 Mount spindle and wheel


Select a recessed type wheel, ensuring that the
head at the securing screw will seat below the face
of the grinding wheel.
4 Dress wheel for roughing out
Apply slight angular relief to the front face of wheel.
5 Set table traverse stops
6 Clean up the bore
7 Measure bore size and parallelism
8 Rough grind bore to within 0.25mm of finished
size.
9 Dress wheel for finish grinding
10 Finish grind bore Very small movement is necessary. Take extreme care in
Note final index reading applying feed, as too heavy cut will tend to make the
spindle whip, causing the wheel to bite into the finished
11 Measure bore
bore.
Safety: Before attempting to measure the bore.
• Clear workpiece from wheel and visually check face
Switch OFF the job rotation and grinding
has fully cleaned up. Take further cuts until a satisfac-
wheel rotation completely.
tory condition is achieved. Allow wheel to “spark out”.

108 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.110
• Re-dress the front face of wheel. • Mount spindle and grinding wheel
• Position wheel in bore. - Select and mount short robust spindle.
• Adjust infeed index to bring the wheel within 0.002mm - Select and mount a recessed wheel of diameter
of the bore diameter. larger than the width of face to be ground. Ensure
the head of the securing screw is below the wheel
• Traverse table until contact is made and apply feed as
face.
in Fig 3.
• Dress the wheel
If a reasonably square corner is required, it
will be necessary to re-dress the wheel face Apply slight angular relief to the front face.
frequently as the corner of the wheel tends to
• Grind the face (Fig 5)
break down.

• Clear workpiece from wheel, stop workhead.


15 Remove sharp corners
16 Check depth - Start workhead.
17 Remove workpiece from machine - Use hand traverse, to position the wheel square to
and just clear of the face to be ground.
Grinding a face (Fig 4)
- Traverse table slowly, until the wheel lightly
contacts the face.
Safety
Safety glasses must be wear.
• With the left hand holding the traverse wheel to act as
a brake, gently tap the handle with the right hand to
advance the workpiece on to the wheel. (Fig 5)
• Very small movement is required. Extreme care should
be taken in applying cuts, as too heavy cut will tend
to make the spindle whip. Allow wheel to spark out.
• Clear workpiece from wheel and visually check face
has fully cleaned up.
• Re-dress face of wheel as necessary.
This type of operation is generally carried out to ensure • Take further cuts as necessary, until a satisfactory
that the face of the workpiece is square to the axis of the condition is achieved.
bore.
• Clear workpiece from wheel, stop workhead.
Basically the procedure is similar to that for grinding a
shoulder, and is a secondary operation following the grinding • Check surface texture and flatness of face.
of the bore. • Remove sharp corners.
• Finish grind bore • Remove workpiece from machine.
Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.110 109
Capital Goods & Manufacturing Exercise 2.4.111
Machinist - Grinding

Internal taper bore grinding


Objectives: At the end of this exercise you shall be able to
• grind the taper bore upto close limit to H6
• check the taper using taper plug gauge.

Job Sequence
• Study the drawing, turn the job as per drawing and • Set the stopper for required stroke length.
maintain the size with grinding allowance. • Rough and finish grind ID taper as shown in Fig 2.
• Ascertain the grinding allowance. • Check the taper using the taper plug gauge.
• Clamp the job in 3 jaw chuck .
• Mount the internal grinding wheel in spindle.
• Dress the wheel.
• Swivel the work head to the MT3 taper angle ()as
shown in Fig 1.

110
Capital Goods & Manufacturing Exercise 2.4.112
Machinist - Grinding

Make male female fitting with an accuracy of ± 0.01mm


Objectives: At the end of this exercise you shall be able to
• set the grinding wheel
• mount the job
• grind the male and female part.

111
Job Sequence
TASK 1

• Prepare the machine for internal grinding and measure • Engage the work head spindle drive.
the grinding allowance. • Take the grinding wheel inside the bore with rotation of
• Fit the internal grinding spindle and mount on wheel job and wheel manually till grinding wheel touches the
head. job make few setting.

• Dress the wheel with a diamond dresser. • Start the coolant supply.

• Measure the existing bore diameter of the job to know • Make repeated cuts until close to the desired size.
the grinding allowance. • Dress the wheel for finish grinding.
• Mount the job in a chuck. • Grind the bore diameter to 30.47mm.
• True the workpiece. • Check the bore size using by telescopic gauge.
• Set the length of stroke. • Remove the job from the chuck.
• Put on your goggles. • Remove burred edges.
• Start the grinding wheel for rotation. • Check the diameter of the job using outside microme-
ter to ascertain the grinding allowance.
TASK 2

• Prepare the machine for external cylindrical grinding. • Finish the surface and maintain the diameter to Ø30g6
• Study the drawing and measure the grinding allowance. on 40 mm long side.

• Set the workhead, wheel head and table at 0o. • Fit the female part.

• Dress the grinding wheel for rough grinding. Use a soft metal spacer if necessary to protect
• Hold the job with suitable dog carrier. the job.

• Mount the job in between centres. • Check the diameter of the workpiece.
• Rough and finish grind the go end surface removing • Remove burred edges.
half of the grinding allowance.
• Remove the workpiece from the centres.

112 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.112
Capital Goods & Manufacturing Exercise 2.4.113
Machinist - Grinding

External step cylindrical grinding with an accuracy of ± 0.01mm


Objectives: At the end of this exercise you shall be able to
• grind by the traverse feed method with an accuracy ±0.01mm
• dress the grinding wheel
• grind steps with shoulder and chamfer
• check and measure the dimension with an outside vernier micrometer
• check the concentricity of the job.

113
Job Sequence
• Study the drawing, turn the job as per drawing and
maintain the size with grinding allowance.
• Ascertain the grinding allowance.
• Check the grinding wheel is rotating in correct
direction.
• Set the work head, wheel head and table at 0º.
• Dress the wheel.
• Mount the workpiece in between centres with carrier.
• Start the machine for grinding wheel rotating.
• Move the grinding wheel back about 50 mm from the
workpiece to allow the wheel to clear the carrier.
This will prevent accidental contact between
the wheel and the carrier.
• Set the length of stroke.
• Move the table automatically in traverse feed. (Fig 1)
• Rough finish to grind the step 50 x 75 mm long.
• Feed the work traversely.
• Grind the step 30 x 45 mm long rough and finish
grinding at both ends one after other. (Fig 2)
• Remove the job from the centres and dog carrier.
• Measure and check the job using by outside
vernier-micrometer (25-50 mm).
• Check the concentricity of job using Dial Test Indica-
tor. Keep your hands away from the revolving
wheel at all times to avoid injuries to
yourself.

Skill Sequence
Checking the concentricity of job (Fig 1)
Objective: This shall help you to
• check the concentricity of the cylindrical job using ‘V’ block and DTI.

• Mount the job in ‘V’ blocks.


• Touch the dial plunger on job.
• Rotate the job for concentricity test.
• See the reading of dial.
• Measure the reading position of Dial Test Indicator for
concentricity.

114 Capital Goods & Manufacturing: Machinist (NSQF Level-5) - Exercise 2.4.113
Capital Goods & Manufacturing Exercise 2.4.114
Machinist - Grinding

External taper cylindrical grinding with an accuracy of ± 0.01mm


Objectives: At the end of this exercise you shall be able to
• hold the job in chuck
• set the table according to taper angle
• set cutting speed, feed and depth of cut
• rough grind & finish grind the workpiece within accuracy
• check the taper by using standard gauge.

Job Sequence
• Determine the grinding allowance. • Start the grinding wheel and the job for rotation.
• Balance the grinding wheel. • Bring the wheel to the job and allow it to touch.
• Mount the wheel on the cylindrical grinding machine. • Grind the job (giving required feed) to an accuracy of
± 5 minutes.
• Dress the grinding wheel.
• Move the wheel away from the job and stop the
• Hold the job in between centres.
movement of the wheel and job.
• Tilt the table of 1o30 to grind.
• Check the taper angle with a vernier bevel
• Set the table traverse dog to grind 130.8 mm length protractor.
on the taper end.

115
 
 
 

You might also like