Service Manual: Multimedia Projector

TopPage
XR-10X-L/XR-10S-L/XG-MB50X-L/XR-11XC-L/XR-HB007X-L
SERVICE MANUAL
No. S06X4XR10XLSL
MULTIMEDIA PROJECTOR
B as ic
XR-10X-L
XR-10S-L
XR-11XC-L
XR-HB007X-L
MODELS XG-MB50X-L
CONTENTS
SAFETY PRECAUTION CHAPTER 5. TROUBLE SHOOTING TABLE
IMPORTANT SERVICE SAFETY NOTES .............i [1] TROUBLE SHOOTING TABLE .....................5-1
Precautions for using lead-free solder ..............vi
CHAPTER 6. BLOCK DIAGRAM/OVERALL WIRING
CHAPTER 1. OPERATION MANUAL DIAGRAM
[1] Specifications ................................................. 1-1 [1] BLOCK DIAGRAM.........................................6-1
[2] Parts Name and Basic Operation................... 1-2 [2] OVERALL WIRING DIAGRAM ......................6-3
[3] DIMENSIONS ................................................ 1-8
[4] Regarding the lamp........................................ 1-9 CHAPTER 7. PRINTED WIRING BOARD
[1] MAIN Unit ......................................................7-1
CHAPTER 2. REMOVING OF MAJOR PARTS [2] DMD Unit .......................................................7-9
[1] Removing the lamp door and the lamp unit ........ 2-1 [3] BALLAST POWER Unit............................... 7-11
[2] Removing the top body .................................. 2-1 [4] BALLAST CONTROL Unit...........................7-17
[3] Removing the main PWB unit ........................ 2-2 [5] PHOTOSENSOR Unit .................................7-19
[4] Removing the speaker, fan, and power [6] R/C Unit .......................................................7-20
supply ballast unit........................................... 2-2
[5] Removing the optical mechanism unit and CHAPTER 8. WAVEFORMS
RC light receiver PWB ................................... 2-3 [1] WAVEFORMS ...............................................8-1
[6] Removing the photosensor PWB unit,
blower fan, DMD PWB, and DMD .................. 2-3 CHAPTER 9. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIA-
CHAPTER 3. THE OPTICAL UNIT OUTLINE GRAM............................................................9-1
[1] THE OPTICAL UNIT OUTLINE...................... 3-1 [2] SCHEMATIC DIAGRAM ................................9-2
CHAPTER 4. ELECTRICAL ADJUSTMENT Parts Guide

[1] ELECTRICAL ADJUSTMENT........................ 4-1
[2] Adjustment mode process menu.................... 4-4
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for

after sales service only.
The contents are subject to change without notice.
Downloaded from www.Manualslib.com manuals search engine
XR-10X-L
SAFETY PRECAUTION Service Manual
IMPORTANT SERVICE SAFETY NOTES
IMPORTANT SERVICE SAFETY NOTES (for USA)

Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and servicing guidelines as follows:
WARNING Use an AC voltmeter with sensitivity of 5000 ohm per
volt., or higher, sensitivity to measure the AC voltage
1. For continued safety, no modification of any circuit drop across the resistor.
should be attempted. All checks must be repeated with the AC plug
2. Disconnect AC power before servicing. connection reversed. (If necessary, a non-polarized
adapter plug must be used only for the purpose of
BEFORE RETURNING THE PROJECTOR: completing these checks.)
(Fire & Shock Hazard) Any reading of 0.4 volts RMS (this corresponds to 0.27
Before returning the projector to the user, perform milliamp. AC.) or more is excessive and indicates a
the following safety checks: potential shock hazard which must be corrected before
1. Inspect lead wires are not pinched between the chassis returning the unit to the owner.
and other metal parts of the projector.
2. Inspect all protective devices such as non-metallic
DVM
control knobs, insulating materials, cabinet backs, AC SCALE
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical 1.5k ohm
10W
insulators, etc.
3. To be sure that no shock hazard exists, check for
current leakage in the following manner:
Plug the AC cord directly into a 120 - volt AC outlet, 0.15 µF
TEST PROBE
(Donot use an isolation transformer for this test).
Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in parallel
between all exposed metal cabinet parts and earth
TO EXPOSED CONNECT TO
ground. METAL PARTS KNOWN EARTH
GROUND
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in DMD™ replacement parts must be identical to those used in
Projector have special safety-related characteristics. the original circuit. The use of a substitute replacement
These characteristics are often not evident from visual parts which do not have the same safety characteristics
inspection, nor can protection afforded by them be as the factory recommended replacement parts shown
necessarily increased by using replacement components in this service manual, may create shock, fire or other
rated for higher voltage, wattage, etc. hazards.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by “ ” WARNING: The bimetallic component has the primary
and shaded areas in the Replacement Parts Lists and conductive side exposed. Be very careful in
handling this component when the power is on.
Schematic Diagrams. For continued protection,
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
PRECAUTIONS A PRENDRE LORS DE LA REPARATION

Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit. Utiliser un voltmètre CA d'une sensibilité d'au moins
C'est dangereux. 5000Ω/V pour mesurer la chute de tension en travers
2. Débrancher le récepteur avant toute réparation. de la résistance.
Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au châssis
VERIFICATIONS CONTRE L'INCEN-DIE ET (antenne, coffret métallique, tête des vis, arbres de
LE CHOC ELECTRIQUE commande et des boutons, écusson, etc.) et mesurer la
chute de tension CA en-travers de la résistance. Toutes
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications doivent être refaites après avoir inversé
les vérifications suivantes.
la fiche du cordon d'alimentation. (Si nécessaire, une
1. Inspecter tous les faisceaux de câbles pour s'assurer
prise d'adpatation non polarisée peut être utilisée dans
que les fils ne soient pas pincés ou qu'un outil ne soit
le but de terminer ces vérifications.)
pas placé entre le châssis et les autres pièces
La tension de pointe mesurèe ne doit pas dépasser 0.4V
métalliques du récepteur.
(correspondante au courant CA de pointe de 0.27mA).
2. Inspecter tous les dispositifs de protection comme les
Dans le cas contraire, il y a une possibilité de choc
boutons de commande non-métalliques, les isolants, le
électrique qui doit être supprimée avant de rendre le
dos du coffret, les couvercles ou blindages de réglage
récepteur au client.
et de compartiment, les réseaux de résistance-capacité,
les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en
vérifiant la fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120 - V. (Ne pas utiliser de
transformateur d'isolation pour cet essai). DVM
A l'aide de deux fils à pinces, brancher une résistance ECHELLE CA
de 1.5 kΩ 10 watts en parallèle avec un condensateur
de 0.15µF en série avec toutes les pièces métalliques 1.5k ohm
10W
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à la
terre.
0.15 µF
SONDE D'ESSAI
AUX PIECES BRANCHER A UNE

METALLIQUES TERRE CONNUE
EXPOSEES
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans liste des pièces de remplacement et les diagrammes
les projecteur à DMD™ présentent des caractéristiques schématiques. Pour assurer la protection, ces pièces
spéciales relatives à la sécurité, qui ne sont souvent pas doivent être identiques à celles utilisées dans le circuit
évidentes à vue. d’origine. L’utilisation de pièces qui n’ont pas les mêmes
Le degré de protection ne peut pas être nécessairement caractéristiques que les pièces recommandées par l’usine,
augmentée en utilisant des pièces de remplacement indiquées dans ce manuel, peut provoquer des
étalonnées pour haute tension, puissance, etc. électrocutions, incendies ou autres accidents.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; AVERTISSEMENT: La composante bimétallique dispose du
les pièces électriques qui présentent ces particularités conducteur primaire dénudé. Faire attention
lors de la manipulation de cette
sont identifiées par la marque “ ” et hachurées dans la composante sous tension.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
NOTE TO SERVICE NOTE POUR LE PERSONNEL

PERSONNEL D’ENTRETIEN
////////////////////////////////////////////////////////////// //////////////////////////////////////////////////////////////
UV-RADIATION PRECAUTION PRECAUTION POUR LES RADIATIONS UV
////////////////////////////////////////////////////////////// //////////////////////////////////////////////////////////////
The light source, lamp, in the projector emits small La source de lumière, la lampe, dans le projecteur émet
amounts of UV-Radiation. de petites quantités de radiation UV.
EVITEZ TOUTE EXPOSITION DIRECTE DES
AVOID DIRECT EYE AND SKIN EXPOSURE. YEUX ET DE LA PEAU.
Pour votre sécurité, nous vous prions de respecter
To ensure safety please adhere to the following: les points suivants:
1. Toujours porter des lunettes de soleil lors d’un entretien

1. Be sure to wear sun-glasses when servicing the du projecteur
projector with the lamp avec la lampe allumée
turned “on” and the top et le haut du coffret retiré.
enclosure removed.
2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier

2. Do not operate the lamp outside of the lamp housing. de lampe.
3. Ne pas faire fonctionner plus de 2 heures avec le coffret

3. Do not operate for more than 2 hours with the enclosure retiré.
removed.
Précautions pour les radiations UV

UV-Radiation and Medium Pressure
et la lampe moyenne pression
Lamp Precautions
1. Toujours débrancher la fiche AC lors du remplacement
1. Be sure to disconnect the AC plug when replacing the de la lampe.
lamp. 2. Laisser l’unité refroidir pendant une heure avant de
2. Allow one hour for the unit to cool down before procéder à l’entretien.
servicing. 3. Ne remplacer qu’avec une lampe du même type. Type
3. Replace only with same type lamp. Type AN-XR10L2 AN-XR10L2, caractéristique 220W-DC.
rated 220W DC. 4. La lampe émet de petites quantités de radiation UV-
4. The lamp emits small amounts of UV-Radiation, avoid éviter tout contact direct avec les yeux.
direct-eye contact. 5. La lampe moyenne pression implique un risque
5. The medium pressure lamp involves a risk of explosion. d’explosion. Toujours suivre les instructions
Be sure to follow installation instructions described d’installation décrites ci-dessous et manipuler la lampe
below and handle the lamp with care. avec soin.
iii
//////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////
UV-RADIATION PRECAUTION (Continued) PRECAUTION POUR LES RADIA TIONS UV (Suite)
//////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////
Lamp Replacement Remplacement de la lampe
Note: Remarque:
Since the lamp reaches a very high temperature during Comme la lampe devient très chaude pendant le
units operation replacement of the lamp should be fonctionnement de l’unité, son remplacement ne doit
done at least one hour after the power has been turned être effectué au moins une heure après avoir coupé
off. (to allow the lamp to cool off.) l’alimentation (pour permettre à la lampe de refroidir).
Installing the new lamp, make sure not to touch the En installant la nouvelle lampe, s’assurer de ne pas
lamp (bulb) replace the lamp by holding its reflector toucher la lampe (ampoule). Remplacer la lampe en
2 . tenant son réflecteur 2 .
[Use original replacement only.] [N’utiliser qu’un remplacement d’origine.]
1 Lamp 1 Lampe
2 Reflector 2 Reflecteur
DANGER ! –– Never turn the power on without the DANGER ! –– Ne jamais mettre sous tension sans la
lamp to avoid electric-shock or damage of the devices lampe pour éviter un choc électrique ou des
since the stabilizer generates high voltages at its start. dommages des appareils car le stabilisateur génère
de hautes tensions à sa mise en route.
Since small amounts of UV-radiation are emitted Comme de petites quantités de radiation UV sont
from an opening between the exhaust fans, it is rec- émises par une ouverture entre les ventilateurs as-
ommended to place the cap of the optional lens on pirants, il est recommandé de placer le capuchon de
the opening during servicing to avoid eye and skin l’optique optionnelle sur l’ouverture pendant l’entretien
exposure. pour éviter une exposition des yeux et la peau.
To illuminate the lamp in the unit with Top Body

removed, attach the above Service Top Body
(DBDYTA132WJZZ). If not, problems may be caused
by UV light emitted from the lamp.
Top Body
Part code:DBDYTA132WJZZ
iv
WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
MOISTURE OR WET LOCATIONS.
CAUTION The lighting flash with arrowhead within a

RISK OF ELECTRIC SHOCK. triangle is intended to tell the user that
DO NOT REMOVE SCREWS parts inside the product are risk of electric
EXCEPT SPECIFIED USER shock to persons.
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

The exclamation point within a triangle is
DO NOT REMOVE CABINET.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. intended to tell the user that important
REFER SERVICING TO QUALIFIED SERVICE operating and servicing instructions are in
PERSONNEL. the manual with the projector.
CAUTION
(POWER Unit)
For continued
protection against a
risk of fire, replace
only with same type
6.3A, AC250V fuse.
6.3A 250V (F701)
AVERTISSEMENT: Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder
directement. Veiller particulièrement à éviter que les enfants ne fixent directement le
faisceau lumineux.
AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER

CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE.
ATTENTION L’éclair terminé d’une flèche à l’intérieur

RISQUE d’un triangle indique à l’utilisateur que les
D’ÉLECTROCUTION. NE pi‘eces se trouvant dans l’appareil sont
PASR ETIRER LES VIS Á susceptibles de provoquer une décharge
L’EXCEPTION DE LA VIS DE
REPARATION UTILISATEUR électrique.
SPECIFIEES
Le point d’exclamation à l’intérieur d’un
ATTENTION: POUR EVITER TOUT RISQUE triangle indique à l’utilisateur que les
D’ELECTROCUTION, NE PAS RETIRER LE CAPOT.
AUCUNE DES PIECES INTERIEURES N’EST REPARABLE instructions de fonctionnement et
PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE d’entretien sont détaillées dans les
LAMPE. POUR TOUTE REPARATION, S’ADRESSER A UN documents fournis avec le projecteur.
TECHNICIEN D’ENTRETIEN QUALIFIE.
PRECAUTION
(Unité de PUTSSANCE)
Pour une protection
continue contre un
risques d’incendie, ne
remplacer qu’avec un
fusible 6.3A,AC250V
6.3A 250V du même type.
(F701)
v
Precautions for using lead-free solder
Employing lead-free solder

• "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
LFa
Indicates lead-free solder of tin, silver and copper.
Using lead-free wire solder

• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No. Description Code
ZHNDAi123250E J φ0.3mm 250g(1roll) BL

ZHNDAi126500E J φ0.6mm 500g(1roll) BK
ZHNDAi12801KE J φ1.0mm 1kg(1roll) BM
vi
CHAPTER 1. OPERATION MANUAL
XR-10X-L
Service Manual
[1] Specifications
Product type Projector

Model XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-10S-L/XR-HB007X-L
Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Display method Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments
DMD panel Panel size: [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-HB007X-L] 0.55" (14 mm), 1chip XGA DMD
[XR-10S-L] 0.55" (14 mm), 1chip SVGA DMD
No. of dots: [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-HB007X-L] 786,432 dots (1,024 [H] x 768 [V])
[XR-10S-L] 480,000 dots (800 [H] x 600 [V])
Lens [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-10S-L/XR-HB007X-L] 1-1.15 zoom lens, F2.4-2.6, f = 19.0-21.9 mm
Projection lamp [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-10S-L/XR-HB007X-L] 220 W DC lamp (AN-XR10L2)
Component input signal 15-pin mini D-sub connector
(INPUT1/2) Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-HB007X-L] 600 TV lines (DTV720P)
[XR-10S-L] 520 TV lines (DTV720P)
Computer RGB input 15-pin mini D-sub connector
(INPUT 1/2)/output RGB separate/sync on green type analog input: 0-0.7 Vp-p, positive, 75 Ω terminated
(OUTPUT) signal HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
S-video input signal 4-pin mini DIN connector
(INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Video input signal RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
(INPUT 4) terminated
Vertical frequency 45-85 Hz
Horizontal frequency 15-70 kHz
Pixel clock 12-108 MHz
RS-232C terminal 9-pin mini DIN connector
Audio input signal φ3.5 mm minijack or RCA terminal: 0.5 Vrms, more than 22 kΩ (stereo)
Audio output signal φ3.5 mm minijack: 0.5 Vrms, less than 2.2 kΩ
(AUDIO OUTPUT 1-4)
Speaker system 4 cm x 2.85 cm oval x 1
Rated voltage AC 100-240 V
Input current [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-10S-L/XR-HB007X-L] 3.0 A
Rated frequency 50/60 Hz
Power consumption XG-MB50X-L/XR-10X-L/XR-HB007X-L 298 W ("Bright" mode)/229 W ("Eco + Quiet" mode) with AC 100 V
XR-11XC-L/XR-10S-L 288 W ("Bright" mode)/223 W ("Eco + Quiet" mode) with AC 240 V
Power consumption 4.7 W (AC 100 V) - 6.1 W (AC 240 V)
(standby)
Heat dissipation XG-MB50X-L/XR-10X-L/XR-HB007X-L 1,120 BTU/hour ("Bright" mode)/860 BTU/hour ("Eco + Quiet" mode) with AC 100 V
XR-11XC-L/XR-10S-L 1,080 BTU/hour ("Bright" mode)/840 BTU/hour ("Eco + Quiet" mode) with AC 240 V
Operating temperature 41 F to 95 F (+5 C to +35 C)
Storage temperature -4 F to 140 F (-20 C to +60 C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 12 13/32"ıx 4 19/64"ıx 11 1/32"ı(315 (W) x 109 (H) x 280 (D) mm) (main body only)
12 13/32"ıx 4 47/64"ıx 11 37/64"ı(315 (W) x 120 (H) x 294 (D) mm) (including adjust-
ment foot and projecting parts)
Weight (approx.) 8.6 lbs. (3.9 kg)
Replacement parts Remote control, Power cord, RGB cable, 3 RCA to 15-pin D-sub cable, DIN-D-
sub RS-232C adaptor, Operation manual, Dust filter
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specifica-
tion figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
1–1
[2] Parts Name and Basic Operation
Part Names and Functions
Projector
Top View
Power Lamp indicator
indicator
Temperature warning
indicator
STANDBY/ON
button
For turning the
power on and Volume buttons
putting the ( / +)
projector into For adjusting the speaker
standby mode. sound level.
INPUT button ( / )
ENTER button For switching input mode
For setting 1, 2, 3 or 4.
items selected
or adjusted on
the menu. MENU/HELP button
For displaying
KEYSTONE adjustment and
button setting screens, and
For entering help screen.
the Keystone
Correction Adjustment buttons
mode. ( / / / )
For selecting menu items.
Front View
Intake vent
Focus ring Zoom ring

For adjusting For enlarging/
the focus. reducing the picture.
Remote control
sensor
HEIGHT
ADJUST
lever
Push both sides of the lens cap
to attach or remove.
1–2
Rear View
Terminals Refer to "INPUT Terminals and Connectable Main Equipment".
AUDIO (INPUT 1, 2) OUTPUT (INPUT 1, 2)
terminal (Shared for terminal
INPUT 1 and 2) (Shared computer RGB and
component signals output
terminal for INPUT 1 and 2)
Terminal for connecting a
monitor.
INPUT 1 and
INPUT 2 terminals
Terminals for INPUT 3 terminal
computer RGB Terminal for connect-
and component ing video equipment
signals. with an S-video
terminal.
RS-232C
terminal
Terminal for
controlling the
projector using
a computer.
AUDIO OUTPUT
terminal AUDIO (INPUT
Audio output 3, 4) terminal
terminal of (Shared for
equipment INPUT 3 and 4)
connected to the
AUDIO INPUT
terminal. INPUT 4 terminal
Terminal for
connecting video
equipment.
Exhaust vent
Speaker
Intake vent
Kensington Security
AC socket Standard connector
Rear adjustment Connect the supplied
foot Power cord.
Using the Kensington Lock

This projector has a Kensington Security Standard connector for use with a Kensington
Micro Saver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
1–3
STANDBY button ON button

For putting the For turning the power on.
projector into the
standby mode.
MENU/HELP button
KEYSTONE button For displaying adjustment
For entering the and setting screens, and
Keystone Correction help screen.
mode.
RETURN button Adjustment buttons
For returning to the ( / / / )
previous menu screen For selecting menu items.
during menu operations. For adjusting the Keystone
FORWARD/BACK Correction when in the
Keystone Correction mode.
buttons
Same function as the ENTER button
[Page Down] and [Page For setting items selected
Up] keys on a computer or adjusted on the menu.
keyboard when using the
optional Remote Receiver FREEZE button
(AN-MR2). For freezing images.
BREAK TIMER
button Volume buttons
For displaying the For adjusting the
break time. speaker sound level.
AV MUTE button AUTO SYNC button

For temporarily For automatically adjusting
displaying a black images when connected
screen and turning to a computer.
off the sound.
RESIZE button
For switching the picture
PICTURE MODE size (NORMAL,
button BORDER, etc.).
For selecting the
appropriate picture. INPUT 1, 2, 3 and 4
buttons
For switching to the
respective input modes.
1–4
Inserting the Batteries

1 Press the mark on the cover and slide it in the
direction of the arrow.
2 Insert the batteries.

Insert the batteries making sure the polarities correctly match
the and marks inside the battery compartment.
3 Attach the cover and slide it until it clicks into place.
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Insert the batteries making sure the polarities correctly match the and marks inside the battery
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove
them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
1–5
Connections
INPUT Terminals and Connectable Main Equipment
COMPUTER-RGB/COMPONENT
INPUT 1, 2 terminal OUTPUT terminal
ı Connecting the computer. Connecting the monitor when you want
ı Connecting video equipment with compo- to simultaneously watch the projection
nent output terminal (DVD player, DTV image on the monitor.
decoder, DVD recorder with hard disc,
etc.).
AUDIO (INPUT 1, 2) terminal AUDIO (INPUT 3, 4) terminal

Connecting an audio cable Connecting an audio cable
(Shared audio input terminal for (Shared audio input terminal
INPUT 1 and 2). for INPUT 3 and 4).
Rear View
RS-232C terminal
Connecting the computer to
control the projector.
INPUT 3 terminal
Connecting video equipment with
S-video output terminal (VCR, DVD
player, etc.).
AUDIO OUTPUT terminal

Connecting to an amplifier or other
audio equipment with an audio cable
(commercially available) (Shared
audio output terminal for INPUT 1, 2,
3 and 4). INPUT 4 terminal
Use an audio cable with φ3.5 mm Connecting video equipment without S-
minijack plug to connect to this video output terminal.
terminal.
1–6
Connecting Pin Assignments
COMPUTER-RGB/COMPONENT INPUT1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals:

15-pin mini D-sub female connector
COMPUTER-RGB Input/Output Component Input/Output
1. Video input (red) 1. PR (CR)
2. Video input (green/sync on green) 2. Y
3. Video input (blue) 3. PB (CB)
11 15 4. Not connected 4. Not connected
5. Not connected 5. Not connected
6. Earth (red) 6. Earth (PR)
7. Earth (green/sync on green) 7. Earth (Y)
8. Earth (blue) 8. Earth (PB)
9. Not connected 9. Not connected
10. GND 10. Not connected
1 5 11. Not connected 11. Not connected
6 10 12. Bi-directional data 12. Not connected
13. Horizontal sync signal: TTL level 13. Not connected
14. Vertical sync signal: TTL level 14. Not connected
15. Data clock 15. Not connected
RS-232C Terminal: 9-pin mini DIN female connector
8 Pin No. Signal Name I/O Reference
9 7 1. Not connected
2. RD Receive Data Input Connected to internal circuit
3. SD Send Data Output Connected to internal circuit
4. Not connected
6 3 5. SG Signal Ground Connected to internal circuit
6. Not connected
7. RS Request to Send Connected to CS in internal circuit
5 4 8. CS Clear to Send Connected to RS in internal circuit
9. Not connected
2 1
RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor* (optional
accessory: AN-A1RS) * This adaptor is only supplied with PG-MB66X/PG-MB56X/XG-MB50X-L.
Pin No. Signal Name I/O Reference
1. Not connected
1 5 2. RD Receive Data Input Connected to internal circuit
3. SD Send Data Output Connected to internal circuit
4. Not connected
5. SG Signal Ground Connected to internal circuit
6. Not connected
7. RS Request to Send Connected to CS in internal circuit
6 9 8. CS Clear to Send Connected to RS in internal circuit
9. Not connected
RS-232C Cable recommended connection: 9-pin D-sub female connector
Pin No. Signal Pin No. Signal
1. CD 1. CD
5 1 2. RD 2. RD
3. SD 3. SD
4. ER 4. ER
5. SG 5. SG
6. DR 6. DR
7. RS 7. RS
9 6 8. CS 8. CS
9. CI 9. CI
Note
• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
Projector Computer
Pin No. Pin No.
4 4
5 5
6 6
1–7
[3] DIMENSIONS
Units: inches (mm)
/ (5)
13 64
11 1/32 (280)
/ (9)
23 64
φ9 7/64 (69.2)
2 7/8 (73) 1 55/64 (47)

/ (11) 4 19/64 (109)
7 16
3 5/32 (80) 3 1/16 (77.5)
12 / (315)
13 32
4 7/64 (104)
1 7/8 (47.5)
/16 (11)
1 11/32 (33.8)
7
2 61/64 1 53/64 2 19/32

(75) (46.2) (65.5)
1–8
[4] Regarding the lamp
Regarding the Lamp

Lamp
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display.
Purchase a replacement lamp of type AN-XR10L2 from your place of purchase, nearest Sharp Authorized
Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited
warranty. All service of this projector under warranty, including lamp replacement,
must be obtained through a Sharp Authorized Projector Dealer or Service Center.
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
www.lamprecycle.org or 1-800-BE-SHARP U.S.A. ONLY
Caution Concerning the Lamp

ı This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
ı When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
ı Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
ı Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case
of exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp

Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burn or injury.
ı Carefully change the lamp by following the instructions described in this section. * If you wish,
you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service
Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
1–9
Removing and Installing the

Lamp Unit
Lamp unit
AN-XR10L2
Warning! (for XG-MB50X-L/
Do not remove the lamp unit from the projec- Optional XR-11XC-L/XR-10X-L/
accessory XR-10S-L/
tor right after use. The lamp and parts around XR-HB007X-L)
the lamp will be very hot and may cause burns
or injury.
Info
Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
STANDBY/ON button
the lamp unit or the inside of the projector.
To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the steps
below.
Do not loosen other screws except for the
lamp unit cover and lamp unit.
1 Press STANDBY/ON on the pro-

jector or STANDBY on the re-
mote control to put the projector
into standby mode.
Wait until the cooling fan stops. AC socket
2 Disconnect the power cord.

Unplug the power cord from the AC
socket.
Leave the lamp until it has fully cooled
down (about 1 hour).
1
3 Remove the lamp unit cover.
Turn the projector over. Loosen the user
2
service screw (ı1 ) that secures the lamp
unit cover. Remove the lamp unit cover User service screw
(ˇ2 ). (for lamp unit cover)
1 – 10
Regarding the Lamp (Continued)

4 Remove the lamp unit.
Loosen the securing screws from the
Handle
lamp unit. Hold the lamp unit by the

handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
5 Insert the new lamp unit.

Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing Securing screws
screws.
6 Replace the lamp unit cover.

Align the tab on the lamp unit cover
(ı 1 )and place it while pressing the tab
(ˇ2 ) to close it. Then tighten the user ser-
vice scr ew ( 3 ) to secure the lamp unit
cover.
2
Info 3
If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con- 1
nected to the projector.
Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer AC socket
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
STANDBY/ON
button
1 Connect the power cord.
Plug the power cord into the AC socket
of the projector. ENTER button
MENU/HELP
2 Reset the lamp timer.
While simultaneously holding down button
MENU/HELP, ENTER and on the
projector, press STANDBY/ON on the button
projector.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
1 – 11
CHAPTER 2. REMOVING OF MAJOR PARTS
XR-10X-L
Service Manual
[1] Removing the lamp door and the lamp unit

1. Loosen the lamp door fixing screw. Lift off the lamp door.
2. Remove 2 lamp unit fixing screws to detach the lamp unit.
1-1
Lamp Door
1-2 1-2
Lamp Unit
[2] Removing the top body

1. Remove 8 top body fixing screws to detach the Top body.
Top Body
Bottom Body
2-1
2-1
2–1
[3] Removing the main PWB unit
1. Remove all connectors from the main PWB unit.
2. Remove 2 terminal fixing screws.
3. Remove 3 main PWB fixing screws to detach the main PWB unit.
3-3
[CW]
[RC] [FA] 3-1
[MO]
[LF] [BB]
MAIN PWB Unit
[FD]
[FC]
[EA]
[FB]
[SO]
3-3
3-2
[4] Removing the speaker, fan, and power supply ballast unit
1. Remove the speaker.
2. Remove 2 fans for the power supply ballast unit and 1 fan for the optical mechanism unit.
3. Remove 2 bimetal fixing screws to detach the bimetal.
4. Remove 2 lamp socket fixing screws to detach the lamp socket.
5. Remove 1 inlet fixing screw.
6. Remove 4 ballast unit fixing screws to detach the power supply ballast unit.
7. Remove 4 ballast shield (upper) fixing screws to detach the ballast shield (upper).
8. Remove 2 ballast PWB fixing screws and 1 clip to detach the power supply PWB unit from the ballast shield (lower).
4-6
4-7 Ballast shield (upper)
POWER SUPPLY BALLAST Unit

Lamp Socket
Fans for power supply 4-4 4-7

ballast unit POWER SUPPLY
BALLAST PWB
Fan for Unit 4-8
optical 4-1
mechanism
unit Speaker
4-5 Ballast
4-2 shield
(lower)
4-3
4-8
Bimetal
2–2
[5] Removing the optical mechanism unit and RC light receiver PWB
1. Remove 4 optical mechanism unit fixing screws to detach the optical mechanism unit.
2. Remove the RC light receiver PWB unit.
5-1
Optical Mechanism Unit
RC Light Receiver PWB
5-2
[6] Removing the photosensor PWB unit, blower fan, DMD PWB, and DMD
1. Remove 1 photosensor PWB fixing screw to detach the photosensor PWB.
2. Remove 2 blower fan fixing screws to detach the blower fan.
3. Remove 4 DMD heatsink fixing screws to detach the DMD PWB unit and the DMD.
DMD
DMD socket
DMD PWB Unit Optical Mechanism Unit

Backer plate
DMD heatsink
DMD spring
6-2 6-3
Photosensor PWB Unit
Blower fan 6-1
2–3
CHAPTER 3. THE OPTICAL UNIT OUTLINE
XR-10X-L
Service Manual
[1] THE OPTICAL UNIT OUTLINE

1. Layout for proper setup of the optical components and parts (top view)
(Schematic diagram)
Projection lens
Illumination lens 2
Illumination lens 1
Reflection
mirror
Plastic Lens
Color wheel
UV Glass Lamp
DMD Rod Integrator
Item Function
Lamp Light source. DC high-pressure mercury lamp.
UV/IR cut filter (UV GLASS) Filters out harmful UV and IR rays from the lamp.
Color wheel Splits light from the light source into R, G, B and W through a color filter.
Rod (ROD INTEGRATOR) Assures uniform light ray.
Illumination lens Focus light from the rod on DMD.
(ILLUMINATION LENS 1, 2)
Reflection mirror Reflects light from the illumination lenses toward DMD.
Condencer Lens Condenses the light from the reflection mirror to the DMD and the pupil of the projection lens.
(PLASTIC LENS)
DMD Turns the internal micromirror ON/OFF at the rate of color component of each dot of the input
source to reflect light.
Projection lens Enlarges light from DMD and projects it on a screen.
3–1
2. When the DMD unit has been replaced
If shading shown in Figure 1 appears on the screen after replacing DMD, turn the adjustment screw of the optical engine to adjust the lighting area of
DMD.
1. Loosen the adjustment lever fixing screw 1 . After adjusting the lighting area with the adjustment lever 2 , tighten the adjustment lever fixing
screw 1 .
Tightening order: → → → Fig. 1

Screw torque: 0.44 ± 0.05 N·m
Shading
When mounting DMD, tighten the 4 screws evenly.
3–2
CHAPTER 4. ELECTRICAL ADJUSTMENTService
XR-10X-L
Manual
[1] ELECTRICAL ADJUSTMENT

No. Adjusting point Adjusting conditions Adjusting procedure
1 EEPROM 1. Turn on the power (with the lamp on) and •Make the following settings.
initialization warm up the set for 15 minutes. Press S2551 to call the process mode and execute
"SS2" on SS menu.
2 Model setting (Process menu) 1. Set as below.
1. Select the following group and subject. 10X-L/10S-L : 2
Group: CONFIRM MB50X-L :3
Subject: MODEL 11XC-L :4
HB007X-L : 5
3 Adjustment of CW index 1. Signal input: Send 256 STEP color bar. 1. Feed the signal to input 1.
XGA series (XGA60HZ), 2. Select the adjustment item and adjust the lamp gra-
SVGA series (SVGA60HZ) dation patterns of RGBW so that smooth patterns
2. Select the following group and subject. without noise appear.
Group: ADJUST CW/Auto KS
Subject: CW-INDEX.
W
R
G
B
4 R/G/B contrast adjustment 1. Select the following group and subjects. 1. Measure chromaticity of the 96% white wind pattern
(manual or automatic) Group : ADJUST using CA100.
AD/DLP 2. On the screen where bit dropouts occur, raise the
Subject : R-CONT values of R/G/B-Contrast. Adjust the values so that
G-CONT bright red, green, and blue bit dropouts appear on a
B-CONT black background; and amounts of change in x value
(Process GAMMA interlock) of R and y values of G/B become 100/1000 or more.
2. Feed white signal with the amplitude level 3. If adjustment is performed manually watching the
of 96% (0.67Vpp). screen, make adjustment so that bright red, green,
XGA series (XGA60HZ), SVGA series and blue bit dropouts appear on more than half of the
(SVGA60HZ) screen.
5 RGB white balance adjustment 1. Feed the 50% gray signal. 1. Raise the values of two of R/G/B-GAIN (default:
XGA series (XGA60HZ), 100) so that the following chromaticity values are
SVGA series (SVGA60HZ) obtained using CL200.
2. Select the following group and subjects. x value: 300 ± 5
Group : ADJUST y value: 320 ± 5
AD/DLP
Subject : R-GAIN
G-GAIN
B-GAIN
6 sRGB white balance adjustment 1. Feed the 50% gray signal. 1. Adjust S-G-OS and S-B-OS so that the following
XGA series (XGA60HZ), chromaticity values are obtained using CL200.
SVGA series (SVGA60HZ) x value: 313 ± 5
2. Select the following group and subjects. y value: 329 ± 5
Group : CONFIRM/DLP
Subject : S-G-OS
S-B-OS
7 Audio output check 1. Select the following group and subjects. 1. Check that the start-up sound is heard from the
Group : ADJUST speaker when the ENTER key is pressed.
CW/Auto KS
Subject : CAL
Check items
1 1 Adjustment of RGB brightness 1. Select the following group and subjects. 1. Check the fixed value.
Group : CONFIRM/AD Fixed value : 127
Subject : R-BRIGHT
G-BRIGHT
B-BRIGHT
(Process GAMMA interlock)
4–1
2 Adjustment of Component offset 1. Feed 10-step signal with 480P component 1. Check the fixed value.
100% amplitude. C-R-OS : 260
2. Select the following group and subjects. C-B-OS : 260
Group : CONFIRM/AD
Subject : C-R-OS
C-B-OS
3 Adjustment of DLP Brightness 1. Select the following group and subject. 1. Check the fixed value.
Group : CONFIRM/DLP Fixed value : 256
Subject :R-BLK
G-BLK
B-BLK
4 Video Contrast adjustment 1. Feed NTSC 100% wind pattern signal. 1. Check the fixed value.
(Signal with burst) Fixed value : 124
2. Select the following group and subjects.
Group : CONIRM/VIDEO
Subject : V-CONT
5 Adjustment of Video Brightness 1. Feed NTSC 100% wind pattern signal. 1. Check the fixed value.
(Signal with burst) Fixed value : 68
2. Select the following group and subject.
Group : CONFIRM/VIDEO
Subject : V-BRIGHT
6 Adjustment of Video Tint 1. Feed split color bar. 1. Check the fixed value.
2. Select the following group and subject. Fixed value : 128
Group : CONFIRM/VIDEO
Subject : V-HUE
7 Adjustment of Video color satura- 1. Select the following group and subject. 1. Check the fixed value.
tion Group : CONFIRM/VIDEO Fixed value : 154
Subject : V-COLOR
8 RGB tone reproduction adjust- 1. Feed the SMPTE pattern signal. 1. Make sure the 100% and 95% white as well as the
ment 0% and 5% black gradations are visible.
9 VIDEO white balance adjustment 1. Feed the 50% gray signal. 1. V-R-OS is 132.
2. Select the following group and subjects. V-B-OS is 132.
Group :CONFIRM/VIDEO
Subject : V-R-OS
V-B-OS
10 White balance checking and 1. RGB Inputt Check that there is no deviation of white balance with
readjustment sRGB Input the monitor.
VIDEO Input
DTV Input
DVD Input
11 Off-timer performance 1. Select the following group and subjects. 1. Select OFF from the process mode.
Group :CONFIRM/CHECK Make sure the off-timer starts with 5 minutes
Subject : TEMP-OFF onscreen and count one minute in one second.
And then indication is 0 minute, the power supply of
the set is cut off.
12 Thermistor performance checking 1. Heat the thermistor with a hair dryer. 1. Make sure that the temperature is indicated.
13 Auto sync performance checking 1. Feed the phase check pattern signal. 1. In the VGA, SVGA, XGA and SXGA modes, make
sure the Clock, Phase, H-Pos and V-Pos settings can
be automatically adjusted.
14 Monitor out check 1. Send signals to INPUT 1 and INPUT 2. 1. Check that the same images as seen on the screen
2. Connect another monitor to the monitor appear on the connected monitor and that the sound
out. from the sound source connected to the audio OUT is
3. Connect the audio OUT. heard.
15 RS232C operation check 1. Connect the unit and a PC with the 1. Send a command from the PC, and check it func-
RS232C cable. tions correctly.
16 Model name and version check 1. Select the following group. 1. The model name appears in the MODEL field, and
Group : INFO/VERSION. the firmware version in the VERSION field. Check that
they are correct.
4–2
17 Delivery settings 1. Make the following settings.
Destination Process Remote control

adjustment adjustment
USA SS4 Factory setting at 4
China SS6 Factory setting at 6
Others SS3 Factory setting at 3
* Writing a software program (before main PWB is mounted)

Use the DLP Composer Lite Ver. 4.2 or higher to download the firmware.
After writing the specified version of firmware to the PWB using the RS232C cable, check the version of the written firmware.
If no software program is written, all three LEDs light up in the chassis inspection process.
Calling and quitting the process mode with the control keys on this model.
* Although it is possible for the process OUT to exit using the process menu, the IN/OUT toggle command is also available considering the existing
specification.
1) Calling and quitting
With the menu not displayed, press the "ENTER", "ENTER", "VOL+", "VOL-", "ENTER", "ENTER" and "MENU" keys on the remote control (one for
C50/45 or P25/20 system is also usable) or on the main unit.
2) Others
Press the S2551 process key (toggle) on the main PWB to call and quit the process menu.
NOTE: When adjusting in the process mode, set a signal with a vertical frequency of 60 Hz or no signal. (May not be properly adjusted with other sig-
nals.)
Resetting the lamp timer for this model

1) Resetting procedure
In Stand-by, run this command to clear the operating time of the lamp to 0 and turn on the power.
Press and hold " ", "ENTER", and "MENU", and then press the "STANDBY/ON" key of the set.
Forced disabling of the System-Lock of this model

1) Disabling procedure
With System-Lock input window onscreen, press the "MENU", "ENTER", "ENTER", "MENU", "ENTER", "ENTER" and "MENU" keys, in this order,
on the remote controller.
4–3
[2] Adjustment mode process menu
1st Layer 2nd Layer Default
ADJUST CW/Auto KS CW-INDEX 20
CAL
K-SENS (0)
AD/DLP R-CONT 110
G-CONT 110
B-CONT 110
R-GAIN 100
G-GAIN 100
B-GAIN 100
SS SS1 —
SS2 —
SS3 —
SS4 —
SS5 —
SS6 —
CONFIRM AD R-BRIGHT 127
G-BRIGHT 127
B-BRIGHT 127
C-R-OS 260
C-B-OS 260
DLP R-BLK 256
G-BLK 256
B-BLK 256
S-R-OS 128
S-G-OS 128
S-B-OS 128
VIDEO V-CONT 124
V-BRIGHT 68
V-COLOR 154
V-HUE 128
V-R-OS 132
V-G-OS 128
V-B-OS 132
OFFSET-MODE 0
OFFSET-CONT 0
OFFSET-BRI 0
MODEL MODEL-SELECT 1
CHECK LED-CHK 0
TEMP-OFF —
INFO VERSION MODEL —
VER. —
PATTERN RGB 1
RGB50 1
CORSS 1
STEP 1
COLOR 1
CHR 1
LAMP CURRENT 0
HISTORY1 0
HISTORY2 0
HISTORY3 0
HISTORY4 0
TOTAL 0
TEMP/FAN TEMP1 —
TEMP2 —
FAN0 3
FAN1 3
FAN2 3
OTHER 232C 232C-MODE 0
EXIT
4–4
1. Adjustment of ballast unit output power (lamp power)
1. List of parts requiring adjustment
When replacing the following parts, adjust the ballast unit output power (lamp power).
Part name Ref No. Part code

1 Cement resistor R905 RR-FZA002WJZZ
2 Ballast Control PWB —— DUNTKD148WEF4
3 Ballast microprocessor IC7707 RH-iXB932WJZZQ
4 5V regulator IC7704 VHITA78L05F-1Y
5 Ballast Unit IC7701 VHIM51995AF-1Y
2. Adjustment jigs
The following jigs are required for adjusting the ballast unit output power (lamp power).
Part name Part code Manufacturer

1 Adjustment jig (resistance load 25 Ω) RUNTZA018WJZZ Asahi Communication
2 Connecting cord (conversion cable) QCNWKA016WJZZ SMK
3. Ballast unit output power (lamp power) adjustment method

Adjust the ballast unit output power (lamp power) in the following method.
[Setting method]
Tester
(Voltage)
XG-MB50X-L Ballast Unit
Lamp Cable
XR-11XC-L
XR-10S-L/X-L
XR-HB007X-L
TP1
Projector Adjustment Jig
(RUNTZA018WJZZ)
Connecting Cord TP2
(QCNWKA016WJZZ)
2. Adjustment method
1) Unplug the ballast unit lamp cable of the projector from the lamp and connect the cable to the connecting cord
(QCNWKA016WJZZ).
2) Connect the connecting cord (QCNWKA016WJZZ) to the adjustment jig (RUNTZA018WJZZ).
3) Connect TP1 of the adjustment jig (RUNTZA018WJZZ) to the negative terminal of the tester and TP2 to the positive terminal.
4) Turn on the projector.
5) Check the Lamp setting to “Bright”.
6) Age the projector for 60 seconds or more.
7) Adjust the volume resistor (R7728) of the ballast control PWB (DUNTKD148WEF4) so that the voltage of the tester reaches 74± 0.5 V.
Adjustment value: 74±0.5 V
CAUTION: (1) Caution for electric shock: Do not touch the test points TP1 and TP2 of the adjustment jig when supplying power since a high voltage
and large current is applied to them.
(2) Caution for heat: Be careful that the resistance load of the adjustment jig produces a high temperature when supplying power.
(3) Connection of the lamp cable: Check that the lamp cable and connecting cord (QCNWKA016WJZZ) are connected securely.
Poor connection may cause smoking or ignition due to arc discharge.
4–5
CHAPTER 5. TROUBLE SHOOTING TABLE
XR-10X-L
Service Manual
[1] TROUBLE SHOOTING TABLE
Checking the basic

operation
Does the power LED light NO Has P1701 come off or is it YES
up or flash in red or green? loose? Fully insert the connector.
YES NO
Does the set function with NO

its keys or the remote Go to "Main PWB check".
controller?
YES
Lamp does not turn on or it YES Go to "Checking the lamp

turns off in a short time. light-up".
NO
Nothing is displayed or YES Go to "DMD system

white vertical line noise check".
appears.
NO
Colors are not displayed YES Check PHOTO SENSOR

normally. Color deviation circuit.
and color fluctuation occur.
NO
Are RGB and component NO Go to "RGB and

input displayed normally? component signal check".
YES
Is VIDEO input displayed NO Go to "VIDEO input

normally? check".
YES
Is S-VIDEO input NO Go to "S-VIDEO input

displayed normally? check".
YES
END
5–1
5–2
DMD system check
Check P2501 for breakage

and solder crack and
peripheral resistance for
solder crack.
Check SC9101 for

breakage and solder crack.
Is there any vertical stripe YES

(block noise) on the
Screen?
NO
NO
Is the screen all black?
The main PWB and DMD
YES
PWB are in poor contact.
Check IC2231, IC2201, Check the contact surface
Is 3.27 V applied to IC2231 NO for dirt and smear.
pin(1) and 1.8 V to TL2231? and their peripheral
circuits. Check the DMD connector
YES for breakage.
Reassemble the DMD,
optical mechanism, and
Is 400 MHz on IC2241 pin NO Check IC2241 and DMD PWB.
(20)? peripheral circuits.
YES
Is approx. 7 V applied to NO
TL9303?
YES
Is approx. 26 V applied to NO Check IC9301 and

TL9301? peripheral circuits.
YES
Is approx. -26 V applied to NO

TL9302?
YES
5–3
Power supply PWB

check
Is 6 V applied to pins (7) NO

and (8) of the connector
P704?
1
YES
Is 13 V applied to pins (3) NO Check peripheral circuits of

and (4) of the connector IC703.
P704?
YES
NO
Does the lamp turn on?
YES
Check the main PWB.
Are connectors P704 and NO Securely insert the

CN901 fully inserted? connectors.
YES
Is DC voltage of 380 V NO Is pin (11) of the connector NO

applied to both ends of P704 at "H"? Check the main PWB.
C704?
YES
YES
Check peripheral circuits
of IC902.
Is LAMP-EN/SYNC signal
NO properly sent to pin (14) of NO
Is R766 in the OPEN
the connector P704? Check the main PWB.
status?
(Refer to the waveform
YES chart .)
YES
Check circuits R766 and Are GATE waveforms of

after or replace R766. Q901 appropriate? NO
(See waveform diagram Check the ballast PWB.
.)
5–4
Are connectorsP701 and NO

Securely insert the connectors.
P702 fully inserted?
YES
Is AC voltage between 100 NO

240 V applied to both Replace F701.
ends of C707?
YES
Is the bimetal broken? NO Press the red button on the

(Connection between 1 and bimetal.
2 of P702)
YES
NO NO Check peripheral circuits of

Is R717 open? Is R705 open?
IC703.
YES YES
Check that P704 connector Replace F705.

pin (11) is at "H". Replace Check that the power
R717. supply FAN FB and FC
are not stopped.
5–5
Checking the lamp

light-up
YES Go to "Check when the

Does the lamp turn on lamp turns off soon after
when the power is turned turning on".
on?
NO
Is the lamp tight in the YES Securely insert the

socket? connectors.
NO
Has the FPC cable to YES Securely insert the

SC3581 come off or is it connectors.
loose?
NO
Check IC3581 and
Is rotating sound of the NO YES
peripheral circuits. (Refer Replace the color wheel.
color wheel heard?
to the waveform chart .)
YES
NO Check IC1701 and

Is approx. 0.7 V applied to peripheral circuits. (Refer
TL1706? to the waveform chart .)
YES
Has the harness connected

to P702 on the power YES Fully insert the connectors
supply unit come off, or is it
or replace the harnesses.
loose? Otherwise, is it
broken?
NO
Dose the lamp turn on after YES Replace the lamp.

the replacement?
NO
Is 340 VDC applied to both NO Go to "Power supply PWB

ends of C914? check".
YES
Is D911 or D913 short- YES Replace both D911 and

circuited? D913.
NO
Is D914or D910 short- YES Replace D914 or D910,

circuited? whichever is short-circuited.
5–6
Check when the lamp turns

off soon after turning on
Have connectors P1703,

P1721, P1722, P1723 and YES Securely insert the
P1724 come off or are they connectors.
loose?
NO
Is each cooling fan NO

Check the cooling fan.
rotating?
YES
Is approx. 3 V applied to NO Check peripheral circuits of

TL1721? Q1721.
YES
NO Check IC1761, IC3581 and

Is 12 V applied to TL1761? Go to "DMD system check".
peripheral circuits.
YES
Is 2.5 V applied to NO YES Check IC1762 and

TL1763? Is 3.3 V applied to TL1762?
YES NO
Check IC1763 and

NO Check IC1791 and

Is 5 V applied to TL1791? peripheral circuits.
YES
Is 5 V applied to TL1712? NO Is 5 V applied to TL1712 NO Check connection of

with P1703 removed? FB1710.
YES YES
Is the signal of 180 Hz NO Check PHOTO SENSOR

sent to TL1716?(When PWB.
vertical frequency of the
input signal is 60 Hz)
YES
Is the signal of 180 Hz NO Check IC1701 and

sent to TL1706? (When peripheral circuits.
vertical frequency of the
input signal is 60 Hz)
YES
Check the power supply

ballast PWB.
5–7
RGB and component

signal check
Send component signal or

RGB signal of 1080i (or
720P) from INPUT 1 or
INPUT 2. Select INPUT 1
or INPUT 2 using keys on
the main unit or the remote
control.
YES
Is image displayed YES

End
normally?
NO
Are picture signals sent to NO Check IC3002 and the

TL3201, TL3204, and peripheral circuits (check
TL3205? IC3052 for INPUT 2).
YES
NO Check IC1792 and

Is 3.3V applied to TL1792?
YES
NO Check IC1763 and

Is 3.3V applied to TL1762?
YES
Check IC3201 and

5–8
S-VIDEO (INPUT 3) VIDEO (INPUT 4) check

check
Send S-Video signal (color

Send VIDEO signal from
signal) from INPUT 3.
INPUT 4. Use buttons on
Select INPUT 3 using keys
the main unit or the remote
on the main unit or the
control to select INPUT 4.
remote control.
Is image displayed YES

End
normally?
NO
YES Check S-VIDEO terminal

Is image displayed in black
and peripheral circuits of
and white?
Q3311.
NO
NO Check S-VIDEO terminal

Is S-VIDEO signal (Y) sent
and peripheral circuits of
to R3306?
Q3301.
YES
YES Is image displayed

End normally?
NO
Check VIDEO terminal and NO Is VIDEO signal sent to

peripheral circuits of C3326?
Q3321.
YES
Is 1.8 V applied to NO Check IC3352 and

YES

YES

YES
Check IC3351 and

5–9
CHAPTER 6. BLOCK DIAGRAM/OVERALL
XR-10X-L
WIRING
Service DIAGRAM
Manual
[1] BLOCK DIAGRAM
BLOCK DIAGRAM
+ T903
Q904
'
&

6–1
TH9102

6–2
[2] OVERALL WIRING DIAGRAM
OVERALL WIRING DIAGRAM
'
&

6–3

6–4
CHAPTER 7. PRINTED WIRING BOARD
XR-10X-L
Service Manual
[1] MAIN Unit
MAIN Unit (Side-A)
P 1703
P1
CW
PG
+ 1 C 1726
4
1
P 2533
R 2509
R 2511
R 2521
R 2522
R 2513
R 2515
R 2517
R 2518
R 2507
R 2525
R 2514
R 2516
R 2512
R 2510
R 2508
F B 1708
F B 1709 R 2019
F B 2241
IC 2001
C 2241
+2.5V
C 2250
17
R 2506
5 4 JT
R 2505
F B 2201
S C 2531
1 3
C 2245
* R 2504 C 2028 VTE R M1.8V
1 24
C 2031
P 1704 IC 2002 C 2223
RC
C 2248
59 30
R 2503
R 2524 12 13
R 2523 IC 2241 R 2212
R 2211
R 2527 C 2205
) IC 2201
IC 2263 44
14
9
1
+1.5V
22
1
C 2208
C 2207
C 2203
( R 2208
R 2207
22
23 C 2204
C 2262
R 2203
1 R 2202
88 C 2210
Q2531 R 2535 R 2554 R 2553

R 3223
R 2002
R 3219
'
F B 3204 S 2551
R 3218 C 3369
102 IC 3201
103
65 S E R VIC E
R 3355
R 3359
R 3360
R 3217
W
R 3356 C 3363
R 3216
S 2001
R 3214
& N
R 3215
D2532
C 3354
C 3215
C 3216
C 3355
39
F B 3203
F B 2532 R 3213
1 38 +3.3VA
F B 2531 R 3209
IC 3152
R 3212
D2531 16 9
P 2532 IC 3102 C 3370
4
US 1
R 3201
% C 3056
16 9
16 9
1 8 5
IC 3051
8 Ver ABCDE FGH
4
IC 3002
1
C 3513 C 3523 C 3524 C 3514 C 3103 D3105
1 8 1 8
D3057
IC 3001 IC 3052
R 3001
R 3053
4 1
R 3002
5 8
R 3003
$ 5 8
F B 3511 F B 3521
F B 3522 F B 3512 F L3103
PG R 3007 F L3102
1 5 1 5 1
6 10 6 1 0 6
11 15 11 15 11
INP UT1 INP UT2 O

#

7–1
TH2
P 1703
P 1702
P 1721 1 4
CW S C 3581 MO LF P 1705 P 3562

FD
D1730
BB F B 1729
L3 40ohm
R 3589
FA R 3588
R 1707 L1723 L1727
R 3591
C 1724
R 1797 R 1798
C 3591 C 3586 C 3588
Q1724 D1725
C 1726
1 4
DUNTKE 004WE QPWBXE 004WJZZ P 1723
R 1762
FC
P 1724 PG
C 1718
R 1728 F B 1732
Q1725
+2.5V
W +12V
D1726 F B 1730
D2573
P OWE R
D2572 D2571
S n-Ag-Cu
a
LAMP TE MP
S 2552 10 20
S X O
+3.3V
S 2555
S TANDBY /ON
P 3561
TH
+1.5V
UP D1701 R 1702
Q1701
R 1701
C 1701 C 1703
14
S 2556
S 2553 E NTE R S 2557 13
P 1701
EA
B +6V
MINUS +5VA P LUS
B +13V 1 2
S 2559 S 2558
S 2554
C 1717
R 1760
P 1722
K E Y S TONE ME NU
DOWN
D1732
.3VA
L5 40ohm
FB
R 3326
C 3324
CPU C 3325
Q3321
C 3323
C 3322
R 3325
R 3324
L3321
C 3326 L3322 D3321 C 3506

R 3323 D3552
C 3305
C 3304
C 3306
C 3103 D3105 D3102

D3104
D3553
C 3301
7 1 R 3306 C 3504 C 3503

P 3551
F B 3552
D2562
L3302
R 2564
IC 3101 L3301 C 3321

Q3301
C 3104
F B 3501
R 3303
R 3301
R 3311
F L3103
F B 3301
D3301
F L3102 F L3101 8 14 V
R 2563
1 5 Y D2564 SO
D2561
D2563
F B 2561
F B 2562
6 10 C
11 15
OUTP UT
S IDE -A

7–2
MAIN Unit (Chip Parts Side-A)
,
P1703
FB1711
R 1704 R 170
S C2531
P2533
R 2528
R 2529
R 2507 R 2509 R 2511 R 2513 R 2515 R 2517 R 2522

C2002
R 2019
FB1708
IC2001
P1704
FB2241
C2241
C2250
FB1709
FB2201
C2028
R 2518
R 2001 C2003
R 2505
* R 2506 R 2508 R 2510 R 2512 R 2514 R 2516 R 2521 R 2525
C2001 C2031
C2253 C2252 C2246 C2242

R 2504
C2245
R 2241
C2248
IC2241
C2223
R 2503
R 2244
C2251
R 2213 C2222
R 2524
R 2212
C2221
R 2523
R 2527 C2220
R 2211
C2205 R 2204 C2206
) C2219
R 2210
C2218
C2217
IC2201
R 2209
IC2002
C2216
R 2206
IC2263
C2209 C2215
R 2205
C2214
R 2208
C2207 C2203 C2208
( C2213
R 2207
C2204 C2212
R 2214 C2211
R 2005
C2262 R 2004
R 2203 R 2202 C2210
R 1779
R 2534
R 2532
Q2531 R 2533
R 2535
R 3223
R 1759
' R 2002 R 2554 R 2553

R 3221
R 3222
R 3218 R 3219 R 3220

FB3204
C3227
C3222 C3223 R 3224
S 2551
C3220
C3369
C3221
R 3217
FB3354
R 3355
R 3359
R 3360
C3371 C3365 R 3365

R 3216
S 2001
FB3353
C3218
C3219
IC3201
R 3356
C3363
R 3214
& FB3351
R 3215
C3217
C3355
FB3352
FB3202
C3354
P3301 R 3366
D2532
R 3213
C3212
C3364
C3362
C3211
P2532
FB2532
FB3355
R 3209
C3210
C3204
FB2531
C3206
R 3204 C3201
C3207
C3208
R 3205 C3202
C3209
C3203
C3215
C3372
R 3211
R 3212
FB3201
C3216
C3370
FB3203
R 3206
D2531
R 3225
R 3203 R 3201
R 3202
R 3025 R 3023 R 3020 R 3069 R 3072 R 3074
% R 3021 R 3022 R 3024 R 3070 R 3071 R 3073 IC3152
IC3102
C3057
C3056
C3055
IC3002 IC3052 D3017

R 3151 R 3152
D3067
C3152
R 3156
C3153
R 3157
R 3158
C3154
C3151 R 3155 IC3051

D3057
C3513
C3523
C3524
C3514
C3051
D3007
C3103
R 3009
IC3001
R 3002
R 3001
R 3053
R 3052
R 3051
R 3055
R 3054
R 3059
R 3057 R 3511 R 3522 R 3521 R 3512

C3001
R 3010 R 3056 R 3102

$ R 3003 C3511 C3522 C3521 C3512
FB3103
R 3103
FL3103
FB3102
D3056
D3051
D3065
D3066
FB3511 FB3522 FB3521 FB3512

FB3003
FB3002
FB3001
FB3053
FB3052
FB3051
FB3056
FB3055
FB3057
D3006
D3001
D3015
D3016
R 3004
R 3005
R 3007
R 3006
FB3054 R 3058

7–3
P1703 P1702 P3562

P1721 S C3581
P1705
FB3566
FB3565
C3572
FB1711
FB1710
FB1707
FB1723
FB1722
FB1721
R 1708
R 1705
C1705
FB3582
FB3583
D1730 FB3584 FB3585
R 1704 R 1706 L1723
R 1707 L1727
R 3591
R 3588
R 3589
D1733
FB1729
P1723
C1724
C1726
FB1728
R 1727
C3591 C3586 C3588 R 1797 R 1798 Q1724 D1725 FB1727
R 3592
R 3593
P2533 R 1762
8 C1718
9 R 1728
FB1732
Q1725
C1725
D1731
P1724
FB1731
D1726 FB1730
D2573 D2572 D2571
S 2552
P3561
S 2555
R 1702
D1701
Q1701
R 1701
C1703
C1701
S 2553 S 2556 S 2557

P1701
S 2559 S 2558
S 2554
R 1760
C1717
D1732
P1722
5
C3322
R 3325
C3324
C3323
R 3324
C3326 R 3326 D3321 R 3323

L3322 L3321 D3552
C3325 Q3321 C3506
R 3322
C3306
C3305
C3304
D3553
D3102 R 3304
C3303
C3302
R 3305
C3321
C3103 D3105 D3104 L3302

R 3306 C3301
Q3301
L3301
D3101
D3103
C3504
C3503
FB3321
FB3301
FB3311
R 3302 FB3552
R 3303
R 3301
R 3321
R 3102 R 3101
R 3311
D3301
D2562
FB3103
R 3103
FL3103
FL3102
FL3101
IC3101
P3551
FB3102
FB3101
FB3551
FB3105
FB3104
C3104
R 2564
FB3501
FB3502
C3502
R 3502
R 3501
C3501
D2561
D2563
D2564
FB2562
FB2561
R 2563

7–4
MAIN Unit (Side-B)

R 3578
LUG 3103 C 3571
D1702
,
TH3561 R 3577
D3584
C 1722
L1721
D3581
D3582
D3583
R 1729
D1722
C 1728 Q1721 C 1704
R 1726
C 3593 D1723
R 3597 Q1722
1 IC 1762
+ C 1761 1
R 1764 12
C 1763
R 3596
PG R 3595
C 2231
C 1770
L1728 L1724
D1765
R 1765 R 3594
13
1 1
IC 3581 R 2232
D1763
* C 1766
5 F B 3581 IC 1763
C 1721
IC 1761 C 3596 D1762
8 5 5
R 1732 Q2571 Q2572 Q2573 Q2574 Q2575
S n-Ag-Cu
R 2231
a 1 4
C 1765
C 1729
R 2571
C 1767
C 1769
R 2572
C 1781
) F B 3563
C 3565 R 3564
C 3566 IC 3562 20 IC 1721
1 L1761
S 3561
IC 1742
R 1777
3 1 3 1 IC 1741
10 11
IC 3561
IC 1743
R 2020 4
C 3570 5
F B 3564 R 3553 4 5
8
C 1753
( Q3537 R 3563
C 1702
IC 1701 R 1748 C 1750

F B 3561
1 14
1 C 1741
4
13
C 1742
14 C 1743
7 8 F B 1741
3 1 C 1793
F B 1701
D1791
L1741
IC 1791
' R 3558 R 3557 4 6
R 3539 1
2 F B 1702
1
C 1791
Q3536
R 1731 D3551
1 R 1795 5
Q3534
C 1727
C 3538
11 10
R 1730
5
& IC 3552 Q3535 IC 3533
9
8
IC 1792
1
16 1
1 C 1795
5
20 C 3552 4
IC 3551
L1726
R 3556 1
LUG 3102
C 3505
5
C 3532 C 3536
C 1798
% C 3535
R 2568
IC 3531
C 3313
4
L3311
3
C 2561
IC 3601
Q3501
R 3507 L3312
F B 2563
C 3515
C 3315 C 3101 C 3102
Q3502
D3512
9
C 3314
C 3601
R 3109
1 8
D3311
$
S IDE -B
S C 3101
J 3301
S C 2561

7–5
140 2
LUG 2502
LUG 2501
R 1729
139 1
PG
C 2231 R 2017 F B 2251

R 2233
D2231 LUG 3104

X2251
IC 2231
1
R 2232
R 2520
D1763
R 2013 8 R 2502
1 R 2519
5 4 5 L2005
C 2247 IC 2251
R 2231 R 2242 R 2248
R 2243 L2004
R 2531
C 1729
R 2247 R 3587 C 2030 R 2501
R 2245
R 2246 C 2032 C 2034
C 2029 R 2016 IC 2262
R 2007 24 1
C 2026
C 2025
C 2027 C 2020
C 2006
IC 1721 C 2023
C 2016
C 2019
C 2022 C 2018
C 2021
C 2264
C 2011
C 2014
C 2012 C 2013
R 2526
R 2018
C 1750
C 2008 C 2010
C 1741 48
4 1
C 1742
C 1743 C 3368
C 2005
C 2015
5 8
L1741
C 3366 F B 2002 F B 2001 IC 2261
IC 3352
1 R 3362 R 3363
60
IC 3351 41
5
61 40 R 3361
R 3358
C 3357
R 3357
R 3351 R 3210
IC 3004
80 21
X3351 20 C 3226 C 3224
1 6 4
8 C 3356 C 3006
1 C 3213
1 3
C 1795
R 3153
4 5
LUG 3101
D3008
C 3505
D3060 D3059 D3058 D3009

Q3101
C 1798
R 3154
D3511
D3521
D3522
R 3523
R 3108
C 3515
R 3524
R 3110
D3512
R 3513
D3053
D3055
D3052
D3054
C 3003 C 3002
IC 3003
3
1
S C 3051
PG
S C 3001
J 3511

7–6
MAIN Unit (Chip Parts Side-B)

R 3578 C3571
,
TH3561 R 3577 D1702
C1722
C1704
L1721
C3594 D3584 D1723
R 1725 D3581 D3582 D3583
R 1729
C3592 Q1722
Q1721
D1722
C1728
R 1722
R 1726
C3593
C3589
R 3590
C3585
C3584
R 1723 R 3597
D1721
C3595 C3583 C1771
R 1724 R 1721
+
R 1773 R 1780 R 1781

R 3596
C1777
R 1764 IC1762
C1761
C1763
R 3595
IC3581
R 1765 C1768
L1728 L1724 R 3594 D1765
D1761 C2231
R 1761 C1762
D1763
C1770
R 1769
C1766
C3590 C3587
C3582
C1764
C2232
FB3581
C1721 IC1761 C3596 R 2232 C2233
R 1732
* C1773
R 1775
C1776
C1775
R 1772
R 2234
C1772 R 2235
C1760
R 1771 R 2231
R 1768 D1762
R 1770
C1778 IC1763
Q2571 Q2572 Q2573 Q2574 Q2575
C1780
C1765
C1729
R 2571
R 2582 R 2584
R 1774
R 2575 R 2577 R 2579 C1779
C1767
R 2576 R 2578 R 2580 R 2581 R 2583 D1764 C1769
FB1761
C1781
C3530
C1774
IC1721
R 2572
)
R 3579
L1761
R 1777
R 1776
R 3561
C3565 R 3564 R 3562
FB3563 C3566
C3567
C3562
R 3572 C3564 IC3562
S 3561
R 3573 R 3571 FB3562 R 1749 R 1750 C1756 R 1747

R 3576 IC3561 C1755
C3561
C3568
C3569
C1752
IC1743 IC1742 C1751 C1745
R 3567
R 2020
R 3570
C3570 FB3564
C1747
R 1746
R 1744
C1744
R 1743
C3563 C1754
R 3553
FB3561
R 3566
R 3580
Q3537
R 3563 R 1741
D1741
R 3541
C1753
R 1742
( C1748 IC1741
C1750
R 1711
R 1710 C1741
C1702
R 1713 R 1748
FB1703
IC1701
R 1703
R 1745 C1746
FB1704 FB1741 C1742
C1749 D1742
FB1705 C1743
R 1791
R 1792
C1794
FB1706 R 1712
C1792
C1793
R 1709
D1791
L1741
IC1791
FB1701
C3367 D33
'
FB1702 C1791
R 3598
R 3599
C3534
R 3371
C3556
R 3558
R 3557
R 3539 R 3372
IC
R 3533
R 3540
R 1718
R 1731 Q3534 Q3536 R 3568
D3551
R 1717
Q3522
Q1703
R 1716
Q1702
C3557 R 3552
R 3559 R 3551
C3526
C3527
R 3560
R 3548
C1727
R 1795
R 3369
R 3370
IC3552
R 3565 R 3574
R 3547 R 3549
C3538 R 1714 Q3331
C3537 R 3545
C3555 R 3555
R 3554
R 3550
&
C3528
C1711 C1
C3529
R 3531
R 3538 R 3535
R 1730
R 3575
R 3544
C3541
R 3606
Q3535 R 3546 Q3523

Q1723
C3533
IC3551
IC3533
D1724 R 3532 IC1792

FB1726 FB1725
C3540
C1795
D1
R 3542
R 3534 R 3601
C3552
R 3525
R 3526
FB1724
R 3543
C3553
C3545
C3544
R 3537
C3539
R 3536
Q3524 Q3521
L1722
C1796
R 3530 R 3529
R 3518
R 3527
C3525
R 3520
R 3528
C1723
R 1794 C1797
C3531
C3535
R 1715
L1726
C3532
C3536
IC3531 R 1793
R 3604 R 3605
R 3556 C3602
Q3601
IC3601
R 3602
C3554
C3515
C1798
R 3603
%
C3505
FB2563
R 2568
C3313
D3512
L3311
L3312
C3315
C2561 R 3506 R 3507

C3601
C3312
R 2566
Q3501
Q3502
C3314
R 3315
R 3314
R 2565
Q3311
R 3312 C3311
IC2561
C3102
D3501 D3502
C3101
R 3313
R 3504
R 3505
R 3503 D3311 R 3109

C2564
C2565
C2563
R 2567
C2562
$

7–7
P2501
R 1729
1722
FB2251
C1768
C2004
R 2017
C2254
C2231
R 2233
D2231
R 2013
X2251
C2232 R 2520
R 2232 C2233
IC2231
C2256
R 2234 IC2251
R 2252
C2255
R 2502
R 2235
R 2231 R 2519 L2005
R 2242
R 2015
C2035
C2247
R 2008
R 2501
R 2243
R 2531
R 2245 R 2248
R 2009
R 2012
R 2247
L2004
R 2246 R 3587 R 2014
C1729
C2033 C2030 C2032 C2034
R 3582
R 2010 C2501
C2029 R 2016
IC1721 R 2007
R 2263
C2027
C2026 C2025
C2006
C2020
C2023
C2016
C2022 C2019
C2018
C2021
C2264
C2017 IC2262
C2201
R 2201
C2202
C2013 C2014 C2011
R 2018
741
D1741
C2012
R 2526
742
C3581
C1750
R 3569
R 2006
C1741 C2008 C2010 C2009 R 3581

R 2561 C2263
R 2562
R 3583
C1742
C1743 R 3584
C2005 IC2261
R 2003
R 3585
R 3586
C3366 C2007
C2555
C2553
C2551
C2558
C2556
C2554
C2552
C3368
C2015 FB2001 FB2261
C2261
FB2002
C2557
R 2551 R 2552 R 1778 R 2261

C3367 D3331
C1785
C1784
C1783
C1782
R 3362 R 3363
R 3371
IC3352
R 1718
C3359 C3360 C3361

R 1716
Q1702 R 3361
C3358
R 3358
R 3369
R 3370
Q3331 C3357
R 3357
R 3354 R 3367
IC3351
R 3353
R 3368
R 3352
X3351
C1711 C1712 R 3351
R 3210 C3205
R 3208
C3010
C1795
D1703 C3356
IC3004
C3351 C3352 C3353

C3226
R 3044
C1796
R 3207
C3224
C3214
IC1764
FB3207
C1710
R 3040
C3006
FB3206
C3225
C3213
R 1715
R 3043
R 3041 R 3042
R 3153
R 3107 Q3101
R 3154
R 3517 R 3516
D3008
C3515
D3060
D3059
D3058
D3010
D3009
R 3108
Q3512
Q3511
C3505
C3005
R 3065
R 3064
R 3068
R 3063
R 3062
R 3067
R 3061
R 3060
R 3066
R 3016
R 3015
R 3019
R 3014
R 3013
R 3018
R 3011
R 3017
R 3515
R 3514
R 3523
R 3524
R 3012
D3512
R 3110
D3511
D3521
D3522
R 3513
R 3027 R 3026
C3054
C3053
C3052
C3004
C3003
C3002
C3008 C3007
R 3034
R 3028
R 3029
R 3033 D3002 FB3005

D3054
D3053
D3052
D3055
R 3030 Q3102 R 3031 R 3032 FB3007

R 3036 D3003
R 3035 R 3037
FB3004
C3009
IC3003 D3004 R 3008

Q3103 D3005 FB3006
R 3038 R 3039

7–8
[2] DMD Unit
DMD Unit (Side-A)

E
TH9102
R9102
C9101 C9102
R9103
D
C9318
C9507
C9513 C9512
C9313
C9315
R9303
FB9302
R9305
C9314
C9311
C C9505
C9503
C9312
C9316
C9510
SC9101
IC9301
C9310 C9511
C9317
R9304
C9309
C9508
C9502
R9301
R9302
C9307
D9303
FB9303
C9504 C9509 C9506

C9301
L9301
D9302
B
C9302
L9302
C9303
D9301
FB9301
C9306
C9304
C9308
C9305
C9514
C9501
A DMD Unit (Chip Parts Side-A)
1 2 3 4 5 6
7–9
E DMD Unit (Side-B)
1 2 3 4 5 6
7 – 10
[3] BALLAST POWER Unit
BALLASUT POWER Unit (Side-A)
+
LUG 702
7
R 765
R 744
R 745
T 705
R 746
C 734
6
C 733
C 728
D718
C 737
D717
D714
*
2
IC 703
C 726
12
R 739
13
14
4
1
C 725 7
T 704
2
D715
C 704
) C 727 R 741
R 714
P 704
C 732
C 731 C 730
R 734
D712
R 716
C 738
C OLD D716
D711
C 721
1
2
D709
HOT
2
10
1
(
T 901
R 922
6
'
D913
J A101
D911 D912 T H901 G D S
S
D908 G D S
C 920
Q901 Q903
& D910 D914
L701
Q905
C 911
R 905
D
R 766
R 937
6
QP WB ND147WJ N2
G
4
D907
C 901
2
9
%
C 916
T 903
C 917
a
2 1 L902
C 914
C 915
C N901 (-)
(+) L901
$
CPU A B C D E F G H
DUNTKD147WE W Ver A B C D E F G H

7 – 11
R 713
R 709
C 735
LUG 701
C 714
N
L
L705 6.3A-250V P 701
F H701
R 701
C 711
C 712
T 6.3AH
C 707
250V
F H702
T 704
L702
C 704
F 701
R 727
C 740
V A701
R 724
R 722 R 720 R 719
F 705 D703 Q704 G S G S

D
127 D Q702 D701
C 715
F B 707
BA
R 717
C 709 C 710 P 702
R Y 701
1
C 720
L703
2
2 1
3
IC 702
D S
C 901

7 – 12
BALLASUT POWER Unit (Side-B)
R 709
R 713
C 714
C 735
N R 762
L R7
R 711 C 703
C 713
R 710
C 705
R7
* R 703 R 704 R 705
D705
F H701
F 701
C 702 C 706 R7
8
1 IC 902
5
R 702
C 712
C 711
4
R 701 R 718
T 6.3AH
L705
R 732
250V
C 708 D704
R 728 R 712
C 707
F H702
) R 715
R 727
T 704
C 740
F B 705
L702
F B 706
V A701
R 724
R 720
( R 719 R 722
R 721
D706 R 725
R 731
R 730 D707
D719 R 764
D701
R 763 D720
S S
G G F 705
D703 C 903
Q702 Q704
' D F B 707
C 715
L703 D
BA
P 702 C 710 C 709
R 717
R Y 701 R 913
C 716
C 717
R 917
C 720
1
1 2
D702
S
IC 702
2
3
&
Q9
C 923
C 92

7 – 13
F B 704
6
7
R 745
R 744
R 765 F B 701
C 734
F B 702
T 705
R 708
D718
R 707 R 746
5 R 759 R 760
R 706
C 733
C 704
D714
C 719
C 728
D717
D713
2
IC 703
8
C 726
R 736
C 737
2
R 739
R 758 R 757
1
R 735
C 718
R 752 R 754
C 724 R 756
C 729
C 732
4
1
7 R 743
14
13
C 723
2
3
C 727
R 749
D710 R 753 R 751
R 714
C 725 D715 R 755

C 736
P 704
IC 704
R 741 Q705 R 738
R 716
R 734
D712
C 722
Q706
R 737
C 721 C 730 C 731
D711 R 750
1
2
D708 R 742
C 701
C 738 R 740
1
D716
D709 R 733 C 739
2
R 748
10
1 2 3 4 5 6 7 8 9 10 23 24 25 26
T 901
11
2
C 921
4
R 922
R 942
R 940
6
C 904 C 905
R 918 C 919
3 R 904
D915 R 911 R 933 R 928
R 912 R 934 R 941
C 924 R 927 R 947
Q907
D906
R 914
R 903 R 908 C 918 R 938

R 902 R 926 C 902
C 925
R 901 R 921 R 923 R 925 R 948
Q904
R 913 R 907 R 932
Q906
R 924 R 931 R 949

R 917 R 909 F B 903 R 939
R 920
F B 904 R 930
C 910 R 929 D911 D913
S D G
T H901 R 936
J A101
D908 D912
S D G C 909
S
Q903 C 920
L701 Q901 C 912 D914
C 911
Q905 D910
D
R 766
R 937
G
R 935 R 950
4
D907
C 901
C 923 R 945 R 944 R 905

T 903
C 913
2
L902
C 922 R 946 R 943
D909
C 916
L901
C 917
1 2
C 914
C 915
C N901
(-) (+)

7 – 14
BALLAST POWER Unit (Chip Parts Side-B)
R 762
R 708
R 711 C703
C713 R 707
C705
C706 R 710
R 703 R 704 R 705 R 706
* C702 D705
IC902
R 702
R 718
D704
R 732 C708
R 728 R 712
D722
R 715
FB705
FB706
( R 721 R 725
R 730 D706 R 731 D707
D719 R 763 D720 R 764
C903
'
C716
R 917
D702
C717
&
C923

7 – 15
FB704
FB701
R 708
FB702
R 707
R 706
R 759 R 760
D713
C719
R 758 R 757
R 736
C724
C718
R 735
R 752 R 754
R 749
C729
C723 R 756
R 743 R 753 C736
R 751 R 755
D710
IC704
R 738
Q705
C722
D708 R 737
R 750
C701 R 733 R 742

Q706
C739 R 740 R 748
C921
R 918 R 940 R 942

C905
C904
R 933 C919 R 941
C903 R 904
C924 R 911 R 912
D915 R 934
R 928 R 947
R 938
C918 R 927
D906
R 914
Q907
Q904 R 902 R 903 R 908

R 901 C925 R 926 C902
R 932 R 925 R 948

R 921 R 923
Q906
R 913 R 907
R 931 R 939
R 949
R 924 R 920 R 929
R 917 FB904 R 909 FB903 R 930
R 936
C910
C909
C912
R 950
R 935
C913
C923 R 945 R 944
C922 R 946 R 943 D909

7 – 16
[4] BALLAST CONTROL Unit
BALLAST CONTROL Unit (Side A)
R7704
P7701 C7701
D7715
C7736
C7733
R7708
D
IC7701
R7787
R7761
C7745
D7714
C7707
R7712
C7746
C7739
X7701
R7725 R7724
IC7707 C7709
R7772
C7741
C7737
R7717
C7727 R7719
C7752
D7713 C7742 R7775 R7776

C7712 C7713
C7728 R7726
R7770
R7769
C7718
R7793 C7710
D7711 R7721
C7715 IC7709 C7719
C7734
R7762
D7712 D7703 R7731

C Q7707
C7717
R7720
C7744
R7723
C7731
R7755
BALLAST CONTROL Unit (Chip Parts Side A)
1 2 3 4 5 6
7 – 17
BALLAST CONTROL Unit (Side B)
E
C7722
C7720
D7706
D7704
R7709
R7715
R7702 R7703
C7721
C7724
C7751
C7735
D7705
IC7704
R7796
R7794
R7795
R7705 C7702 R7739

R7706
Q7702
D C7705 R7710 C7706 Q7701 C7708
C7730
C7750
C7703
D7702
R7748
R7765
R7763
R7771
R7764
R7707
R7781
R7714
R7759
D7701
C7704 R7788 Q7711

R7780
R7713 R7728
R7784
R7718 R7756
R7737
R7711 R7786 R7785 IC7705

C7711 R7701
R7753 R7716
C7749
R7745
R7744
R7735 C7723
R7730 Q7708
R7733
C7738
R7752 Q7704 Q7703 R7779

Q7705 Q7706
R7783
C7740
R7767 R7741 C7725

R7732 R7742 C7726
R7792
R7729 R7736
R7791
R7790
R7789
R7747
R7740
R7727 R7738
R7777
R7773
C7716 R7722
R7760
R7757
R7751
R7766 R7774 R7749 R7746

C R7750
C7743
R7734
R7778
Q7709 R7758 R7754

R7743
BALLAST CONTROL Unit (Chip Parts Side B)
1 2 3 4 5 6
7 – 18
[5] PHOTOSENSOR Unit
PHOTOSENSOR Unit (Side-A)
D
PHOTOSENSOR Unit (Side B)
C
C1101
R1101
IC1101
R1110
P1101
B
R1102
R1103
R1111
R1104
C1102
R1109 R1108
R1107 R1106
PHOTOSENSOR Unit (Chip Parts Side B)

A
1 2 3 4 5 6
7 – 19
[6] R/C Unit
F
R/C RECEIVER Unit (Side-A)
B
R/C RECEIVER Unit (Side B)
1 2 3 4 5 6
7 – 20
CHAPTER 8. WAVEFORMS
XR-10X-L
Service Manual
[1] WAVEFORMS
8–1
CHAPTER 9. SCHEMATIC DIAGRAM
XR-10X-L
Service Manual
[1] DESCRIPTION OF SCHEMATIC DIA-

GRAM
1. VOLTAGE MEASUREMENT CONDITION:
1. Voltages at test points are measured at the supply voltage of AC
100V/CROSS 10V-240. Signals are fed by a color bar signal gener-
ator for servicing purpose and the above voltages are measured
with a 20k ohm/V tester.
2. INDICATION OF RESISTOR & CAPACITOR:

RESISTOR
1. he unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(J=± 5%, F= ± 1%, D= ± 0.5%)
3. All resistors are 1/10W, unless otherwise noted.
4. All resistors are Carbon type, unless otherwise noted.
C : Solid W : Cement
S : Oxide Film T : Special
N : Metal Coating
CAPACITOR
1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2. All capacitors are 50V, unless otherwise noted.
3. All capacitors are Ceramic type, unless otherwise noted.
(ML): Mylar (TA): Tantalum
(PF): Polypro Film (ST): Styrol
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH “ ”( ) ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF THE
SET. BE SURE TO REPLACE THESE PARTS WITH
SPECIFIED ONES FOR MAINTAINING THE SAFETY AND
PERFORMANCE OF THE SET.
9–1
[2] SCHEMATIC DIAGRAM
MAIN Unit-1
'
&

9–2

9–3
MAIN Unit-2
'
&

9–4

9–5
MAIN Unit-3
'
&

9–6

9–7
MAIN Unit-4
'
&

9–8

9–9
MAIN Unit-5
'
&

9 – 10

9 – 11
MAIN Unit-6 (XR-10X-L/11XC-L/HB007X-L/XG-MB50X-L)
'
&

9 – 12

9 – 13
MAIN Unit-6 (XR-10S-L)
'
&

9 – 14

9 – 15
MAIN Unit-7
'
&

9 – 16

9 – 17
MAIN Unit-8
'
&

9 – 18

9 – 19
DMD Unit-1
DMD Unit-1
,,
++
**
))
((
''
&&
%%
$$
##

9 – 20

9 – 21
DMD Unit-2
'
&

9 – 22

9 – 23
DMD Unit-3
'
&

9 – 24

9 – 25
BALLAST POWER Unit
'
&

9 – 26
AND SHADED COMPONENTS=SAFETY RELATED PARTS

9 – 27
BALLAST CONTROL Unit
'
&

9 – 28
AND SHADED COMPONENTS=SAFETY RELATED PARTS
458

9 – 29
PHOTO SENSOR Unit
'
&

9 – 30

9 – 31
R/C RECEIVER Unit
'
&

9 – 32

9 – 33
— MEMO —
9 – 34
PartsGuide
PARTS GUIDE
MULTIMEDIA PROJECTOR
B as ic
XR-10X-L
XR-10S-L
XR-11XC-L
XR-HB007X-L
MODELS XG-MB50X-L
CONTENTS
[1] PRINTED WIRING BOARD [7] DUNTKD164WEF4

ASSEMBLIES (R/C RECEIVER Unit)
[2] DUNTKE004FMF0/1 (MAIN Unit) [8] CABINET AND MECHANICAL

PARTS
[3] DUNTKD140WEF0 (DMD Unit)
[9] OPTICAL MECHANISM PARTS
[4] DUNTKD141WEF4
(PHOTO SENSOR Unit) [10] SUPPLIED ACCESSORIES
[5] DUNTKD147WEF6 [11] PACKING PARTS

(BALLAST POWER Unit) (NOT REPLACEMENT ITEM)
[6] DUNTKD148WEF4 [12] SERVICE JIGS AND EQUIPMENT

(BALLAST CONTROL Unit) (USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used

for after sales service only.
The contents are subject to change without notice.
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[1] PRINTED WIRING BOARD ASSEMBLIES

N DUNTKE004FMF0 CN N J MAIN Unit (10S-L)
N DUNTKE004FMF1 CN N J MAIN Unit (10X-L/11XC-L/MB50X-L/HB007X-L)
N DUNTKD140WEF0 BT N J DMD Unit
N DUNTKD141WEF4 AP N J PHOTO SENSOR Unit
N DSETUD147FMG1 BZ N J BALLAST POWER Ass'y (with Ballast Control Unit)
BALLAST POWER Unit
N Not Available - - Order the BALLAST POWER Ass'y (DSETUD147FMG1) when replacing power ballast
unit (DUNTKD147WEF6).
N DUNTKD148WEF4 BE N J BALLAST CONTROL Unit
N DUNTKD164WEF4 AN N J R/C RECEIVER Unit
[2] DUNTKE004FMF0/1 (MAIN Unit)
C1701 VCKYCY1EF104ZY AA J Capacitor 0.1 25V Ceramic
C1704 VCEAPF1CW106MY AB J Capacitor 10 16V Electrolytic
C1710 VCEAPF0JW226MY AB J Capacitor 22 6.3V Electrolytic
C1712 VCEAPF1CW336MY AD J Capacitor 33 16V Electrolytic
C1717 VCCCCY1HH220JY AA J Capacitor 22p 50V Ceramic
C1721 VCEAPF1EW106MY AC J Capacitor 10 25V Electrolytic
C1722 RC-KZA066WJZZY AB J Capacitor 1 25V Ceramic
C1741 RC-KZA101WJZZY AC J Capacitor 10 6.3V Ceramic
C1743 VCKYCY1AB105KY AB J Capacitor 1 10V Ceramic
C1745 VCKYCY1HB332KY AA J Capacitor 3300p 50V Ceramic
C1746 VCKYCY1HB103KY AA J Capacitor 0.01 50V Ceramic
C1748 VCAAPD1AJ686MY AE J Capacitor 68 10V Electrolytic
C1750 RC-KZA041WJZZY AC J Capacitor 10 10V Ceramic
C1751 VCKYCY1CB104KY AB J Capacitor 0.1 16V Ceramic
C1770 VCEASH0JN476MY AC J Capacitor 47 6.3V Electrolytic
C1778 VCAAPD1AJ686MY AE J Capacitor 68 10V Electrolytic
C2015 VCEAPF0JW107MY AC J Capacitor 100 6.3V Electrolytic
2
RANK MARK DELIVERY

C2204 VCSNDE0GP107MY AF J Capacitor 100 4V (AL)
C2231 VCEASH0JN476MY AC J Capacitor 47 6.3V Electrolytic
C2242 VCKYCY1HF103ZY AA J Capacitor 0.01 50V Ceramic
C2248 VCCCCY1HH4R0CY AA J Capacitor 40p 50V Ceramic
C3101 VCEAPF0JW227MY AD J Capacitor 220 6.3V Electrolytic
3
RANK MARK DELIVERY

C3201 VCKYCY1EB473KY AA J Capacitor 0.047 25V Ceramic
C3303 VCCCCY1HH681JY AB J Capacitor 680p 50V Ceramic
C3503 VCEAPF1HW105MY AB J Capacitor 1 50V Electrolytic
C3535 VCEAPF0JW107MY AC J Capacitor 100 6.3V Electrolytic
C3552 VCEAPF1CW107MY AC J Capacitor 100 16V Electrolytic
4
RANK MARK DELIVERY

D1703 VHDHSU119//-1Y AB J Diode HSU119TRF-E
D1721 VHDDAN202K/-1Y AB J Diode DAN202KT146
D1723 VHDRB551V30-1Y AC J Diode RB551V-30TE-17
D1741 RH-EX1224CEZZY AB J Zener Diode HZU2.0BTRF
D1742 VHDSFPA73//2EY AD J Diode SFPA-73VL
D1762 RH-EX1234CEZZY AE J Zener Diode HZU3.6B2TRF
D1764 VHDSFPA73//2EY AD J Diode SFPA-73VL
D2561 RH-EX1271CEZZY AB J Zener Diode HZU12B2TRF
D2571 RH-PXA097WJZZY AC N J Photo Diode KPH-1608EC
D2572 RH-PXA038WJZZY AC J Photo Diode SML-521MUWT86
D2573 RH-PXA038WJZZY AC J Photo Diode SML-521MUWT86
D3002 RH-EX1247CEZZY AB J Zener Diode HZU5.6B2TRF
D3008 VHDKDS226//-1Y AB J Diode KDS226-RTK/P
D3581 VHDBAT54SWT-1Y AC J Diode BAT54SWT1G
FB1701 RBLN-A213WJZZY AB N J Ferrite Bead BLN-A213WJ
5
RANK MARK DELIVERY

FB3582 RBLN-A191WJZZY AB J Ferrite Bead BLN-A191WJ
IC1701 VHiAHCT08PH-1Y AE J IC 74AHCT08PW,118
IC1721 VHiLV4053AT-1Y AE J IC SN74LV4053APWR
IC1741 VHiMP1580HS-1Y AL N J IC MP1580HS-LF-Z
IC1742 VHiBD5246G+-1Y AE J IC BD5246G-TR
IC1743 VHiBD5246G+-1Y AE J IC BD5246G-TR
IC1761 VHiPQ120DNA-1Y AG J IC PQ120DNA1ZPH
6
RANK MARK DELIVERY

IC1762 VHiPQ070XN1-1Y AG N J IC PQ070XN01ZPH
IC1763 VHiMP1580HS-1Y AL N J IC MP1580HS-LF-Z
IC1764 VHiSi3025LA-1Y AF J IC SI-3025LSA-TL
IC1791 VHiPQ1K503M-1Y AF J IC PQ1K503M2ZPH
IC1792 VHiPQ033DZ1-1Y AE J IC PQ033DZ01ZPH
IC2001 VHiBU4213G+-1Y AD J IC BU4213G-TR
IC2002 RH-iXA806WJN2Q CC J IC 2504504-0007
IC2201 VHiK4R271F8-1Q BG J IC K4R271669F-TCS8
IC2231 VHiPQ018EN5-1Y AG N J IC PQ018EN5MZPH
IC2241 VHiW134MSQC-1Y AP N J IC W134MSQCT(CG6225AAT)
IC2261 VHiBR24L32F-1Y AG J IC BR24L32F-WE2
IC2262 RH-iXB930WJZZQ AT N J IC iXB930WJ (10X-L/11XC-L/HB007X-L/MB50X-L)
IC2262 RH-iXB931WJZZQ AT N J IC iXB931WJ (10S-L)
IC2263 VHiCY62146E-1Y AZ N J IC CY62146EV30LL-45ZSXIT
IC2561 VHiiSL83220-1Y AQ J IC ISL83220ECVZ-T
IC3001 RH-iXB702WJZZS AH J IC iXB702WJ
IC3002 VHiEL8302iU-1Y AT J IC EL8302IUZ-T7
IC3051 RH-iXB702WJZZS AH J IC iXB702WJ
IC3052 VHiEL8302iU-1Y AT J IC EL8302IUZ-T7
IC3101 VHiVHCT125A-1Y AE J IC TC74VHCT125AFT(EL)
IC3102 VHiTC7WH32U-1Y AE J IC TC7WH32FU(TE12L,F)
IC3152 VHiLCX157MT-1Y AE J IC 74LCX157MTCX
IC3201 VHiMST3583+-1Q AZ N J IC MST3583-LF-110
IC3351 VHiTVP5146P-1Q BG J IC TVP5146PFP
IC3352 VHiPQ018EN5-1Y AG N J IC PQ018EN5MZPH
IC3531 VHiLV4053AT-1Y AE J IC SN74LV4053APWR
IC3533 VHiBA3530FS-1Y AM J IC BA3530FS-E1
IC3551 VHiDA7056AT-1Y AM J IC TDA7056AT/N2,118
IC3552 VHiPQ200WNA-1Y AG N J IC PQ200WNA1ZPH
IC3561 VHiMB8346BV-1Y AN J IC MB88346BPFV-G-BND-EFE1
IC3562 RH-iXA966WJZZY AZ J IC PIC16F819-I/SS
IC3581 VHiA8904SLB-1Y BE J IC A8904SLB-T
J3301 QJAKZA026WJZZ AG N J Jack Video/S-Video/Audio In
J3511 QJAKBA002WJZZ AF N J Jack Audio In/Out
L1721 VPCUN330K1R4NY AC N J Peaking 33µH
L1722 VPCUN150KR63NY AC N J Peaking 15µH
L1741 RCiLPA213WJZZY AG J Coil
L1761 RCiLPA214WJZZY AG J Coil
L2004 VPCUN2R2MR16NY AC J Peaking 2.2µH
L2005 VPCUN2R2MR16NY AC J Peaking 2.2µH
L3301 VPD9M1R0JR57NY AB J Peaking 1µH
L3302 VPD9M1R8JR84NY AC J Peaking 1.8µH
LUG2501 QLUGHA002WJZZ AB J Lug
P1701 QPLGNA071WJZZ AC J Plug 14Pin(EA)
P1702 QPLGN0263TAZZY AB J Plug 2Pin(LF)
P1703 QPLGN0363TAZZY AC J Plug 3Pin(CW)
P1704 QPLGN0364TAZZY AC J Plug 3Pin(RC)
P1721 QPLGN0364TAZZY AC J Plug 3Pin(FA)
P1722 QPLGN0364TAZZY AC J Plug 3Pin(FB)
P1723 QPLGN0464TAZZY AC J Plug 4Pin(FD)
P1724 QPLGN0364TAZZY AC J Plug 3Pin(FC)
P2501 QPLGZA018WJZZQ AW N J Plug 142Pin(to DMD PWB)
P3301 QEARBA011WJFMY AE J Plug Ground-Part
P3551 QPLGN0264TAZZY AC J Plug 2Pin(SO)
P3562 QPLGN0363TAZZY AC J Plug 3Pin(TH2)
Q1702 VS2SC3928AR-1Y AB J Transistor 2SC3928A-T112-1R
Q1703 VS2SA1530AR-1Y AB J Transistor 2SA1530A-T112-1R
Q1721 VSDTA114EE/-1Y AB J Transistor DTA114EETL
Q1722 VSMCH3405++-1Y AD J Transistor MCH3405-TL-E
Q2531 VSNDS332P//-1Y AD J Transistor NDS332P
Q3101 VSDTC114EE/-1Y AB J Transistor DTC114EETL
7
RANK MARK DELIVERY

R1702 VRS-CY1JF103JY AA J Resistor 10k 1/16W Metal Oxide
R1703 VRS-CH1JF100JY AA J Resistor 10 1/16W Metal Oxide
R1704 VRS-CY1JF100JY AA J Resistor 10 1/16W Metal Oxide
R1708 VRS-CY1JF152JY AA J Resistor 1.5k 1/16W Metal Oxide
R1709 VRS-TW2ED000JY AB J Resistor 0 1/4W Metal Oxide
R1714 VRS-TX2HF1R0JY AB J Resistor 1 1/2W Metal Oxide
R1726 VRS-CH1JF562JY AB J Resistor 5.6k 1/16W Metal Oxide
R1731 VRS-TX2HF000JY AB J Resistor 0 1/2W Metal Oxide
R1732 VRS-TX2HF000JY AB J Resistor 0 1/2W Metal Oxide
R1741 VRS-CY1JF123FY AA J Resistor 12k 1/16W Metal Oxide
R1742 VRS-CY1JF222FY AA J Resistor 2.2k 1/16W Metal Oxide
R2002 VRS-CJ1JF101JY AA J Resistor 100 1/16W Metal Oxide
R2013 VRS-CH1JF103JY AA J Resistor 10k 1/16W Metal Oxide
R2018 VRS-TV1JD000JY AA J Resistor 0 1/10W Metal Oxide
8
RANK MARK DELIVERY

R2020 VRS-CJ1JF332JY AA J Resistor 3.3k 1/16W Metal Oxide
R2201 VRS-CY1JF111FY AA J Resistor 110 1/16W Metal Oxide
R2207 VRS-CH1JF390FY AA N J Resistor 39 1/16W Metal Oxide
R2501 VRS-CH1JF272JY AA J Resistor 2.7k 1/16W Metal Oxide (XR-10S-L)
R2503 VRS-CH1JF390JY AA J Resistor 39 1/16W Metal Oxide (except XR-10S-L)
R2572 VRS-CH1JF272JY AA J Resistor 2.7k 1/16W Metal Oxide
R3001 VRS-TW2ED750JY AA J Resistor 75 1/4W Metal Oxide
9
RANK MARK DELIVERY

R3041 VRS-TV1JD750FY AA J Resistor 75 1/16W Metal Oxide
R3151 VRS-CJ1JF102JY AA J Resistor 1k 1/16W Metal Oxide
10
RANK MARK DELIVERY

R3538 VRS-CJ1JF473JY AB J Resistor 47k 1/16W Metal Oxide
R3556 VRS-TX2HF8R2JY AB J Resistor 8.2 1/2W Metal Oxide
R3562 VRS-CH1JF182JY AB J Resistor 1.8k 1/16W Metal Oxide
R3577 VRN-CY1JF472DY AA J Resistor 4.7k 1/16W Metal Film
11
RANK MARK DELIVERY

R3588 VRS-TW2HF151JY AA J Resistor 150 1/2W Metal Oxide
S2001 QSW-SA020WJZZY AE N J Slide Switch
S2551 QSW-K0099TAZZY AC J Service Switch
S2552 QSW-KA029WJZZY AD N J Switch (POWER)
S2553 QSW-KA029WJZZY AD N J Switch (-)
S2554 QSW-KA029WJZZY AD N J Switch (DOWN)
S2555 QSW-KA029WJZZY AD N J Switch (UP)
S2556 QSW-KA029WJZZY AD N J Switch (ENTER)
S2557 QSW-KA029WJZZY AD N J Switch (+)
S2558 QSW-KA029WJZZY AD N J Switch (MENU)
S2559 QSW-KA029WJZZY AD N J Switch (KEYSTONE)
SC2561 QSOCDA036WJZZ AF N J DIN Jack Socket
SC3001 QSOCNA230WJZZ AH N J Socket INPUT1
SC3051 QSOCNA230WJZZ AH N J Socket INPUT2
SC3101 QSOCNA229WJZZ AH N J Socket OUTPUT
SC3581 QCNCWA500WJZZY AC N J Connector 4Pin(MO)
X2251 RCRUAA033WJZZY AQ J Crystal
X3351 RCRSC0170TAZZY AG J Crystal
N LX-BZ3100CEF7 AA N J Screw
N PSLDMA722WJFW AL N J Shield
N PSLDMA726WJFW AF N J Shield
N PSPAZA913WJKZ AB N J Spacer

C9301 RC-KZ0046TAZZY AD J Capacitor 4.7 35V Ceramic
C9315 RC-KZ0072TAZZY AC J Capacitor 1 25V Ceramic
D9301 VHDSFPB76//2EY AD J Diode SFPB-76VL
D9302 VHDSFPB76//2EY AD J Diode SFPB-76VL
D9303 RH-EX1008GEZZY AD J Zener Diode PTZTE258.2B
IC9301 RH-iXA384WJN1Q BR J IC 2503253-0004
L9301 RCiLP0325TAZZY AD J Coil
L9302 RCiLP0325TAZZY AD J Coil
12
RANK MARK DELIVERY

SC9101 QSOCZA102WJZZQ AW N J Socket 142Pin(to MAIN PWB)
TH9102 VHH103KT161-1Y AE J Thermistor
[4] DUNTKD141WEF4 (PHOTO SENSOR Unit)

IC1101 VHiLM393A//-1Y AL J IC LM393APSR
IC1102 VHPGP2S40//-1S AK N J IC PHOTODIODE
P1101 QPLGN0363TAZZY AC J Plug 3Pin(CW)
R1101 VRS-TQ2EF121JY AA J Resistor 120 1/4W Metal Oxide
N QCNW-C221WJQZ AF J Connecting Cord
[5] DUNTKD147WEF6 (BALLAST POWER Unit)
C704 RC-EZA572WJZZ AW J Capacitor 330 420V Electrolytic
C705 VCKYTV1EB474KY AC J Capacitor 0.47 25V Ceramic
! C707 RC-FZA026WJZZ AE J Capacitor 0.47 50V Metallized Plastic Film
C709 RC-KZA271WJZZ AC J Capacitor 470 2kV Ceramic
C710 RC-KZA275WJZZ AD J Capacitor 1000p 2kV Ceramic
! C711 RC-KZ0105GEZZ AD J Capacitor 2200p 250V Ceramic
C713 VCKYTQ1HB224KY AC J Capacitor 0.22 50V Ceramic
C714 RC-FZA124WJZZ AG J Capacitor 2.2 450V Metallized Plastic Film
! C715 RC-FZA026WJZZ AE J Capacitor 0.47 50V Metallized Plastic Film
C716 VCKYTV1EB104KY AB J Capacitor 0.1 25V Ceramic
C718 VCKYTV1HB103KY AA J Capacitor 0.01 50V Ceramic
C720 VCEA4A1VN476M+ AC J Capacitor 47 35V Electrolytic
C722 VCKYTV1HB222KY AA J Capacitor 2200p 50V Ceramic
C723 VCKYTV1HB471KY AA J Capacitor 470p 50V Ceramic
C724 VCKYTV1HB103KY AA J Capacitor 0.01 50V Ceramic
C725 VCEA4A1HN105M+ AB J Capacitor 1 50V Electrolytic
C726 RC-KZA050WJZZ AD J Capacitor 450p 50V Ceramic
C728 RC-FZ0010TAZZ AC J Capacitor 0.01 630V Metallized Plastic Film
C732 RC-EZ1208CEZZ AD J Capacitor 2200 25V Electrolytic
C733 RC-KZ0384CEZZ+ AC J Capacitor 1000p 50V Ceramic
C734 RC-KZ0384CEZZ+ AC J Capacitor 1000p 50V Ceramic
C737 RC-EZ1241CEZZ AE J Capacitor 2200 25V Electrolytic
C740 RC-FZA126WJZZ AE J Capacitor 0.1 450V Metallized Plastic Film
C901 RC-FZA215WJZZ AH J Capacitor 1.8 450V Metallized Plastic Film
C902 RC-KZA448WJZZY AD N J Capacitor 220p 1kV Ceramic
C911 RC-FZA123WJZZ AF J Capacitor 1 450V Metallized Plastic Film
C912 RC-KZA437WJZZY AD N J Capacitor 1000p 630V Ceramic
! CN901 QCNW-E997WJQZ AV N J Connecting Cord
! D701 VHDD10XB60H-1 AL N J Diode D10XB60H-7101
D702 VHD1SS355//-1Y AB J Diode 1SS355TE-17
D703 RH-DXA073WJZZ AM N J Diode YG97S6R
D705 VHDLi114+++-1Y AC J Diode LI114
D706 VHDRB160M40-1Y AC J Diode RB160M-40TR
13
RANK MARK DELIVERY

D708 VHDD1FL20U/-1Y AC J Diode D1FL20U
D709 RH-DX0066GEZZY AC J Diode AL01ZV1
D710 RH-EX1294CEZZY AB J Zener Diode HZU27BTRF-E
D713 VHDD1FL20U/-1Y AC J Diode D1FL20U
D714 RH-DXA070WJZZY AE N J Diode SARS01V1
! D715 RH-FXA003WJZZ AD J Diode PC123Y82
! D716 RH-FXA003WJZZ AD J Diode PC123Y82
D717 RH-DX0459CEZZ AE J Diode D5S4M
D718 RH-DX0469CEZZ AF J Diode D3S6M
D907 VHSG1VB22C+-1 AK J Diode SI.Control Rectifier
D908 RH-DXA074WJZZ AH J Diode SF10L60U-7100
D909 VHDU1JU44//-1Y AE J Diode U1JU44(TE12R,Q)
D910 RH-DXA062WJZZY AE J Diode SHV-04V6
D911 VHDFMQG2FLS-1 AN N J Diode FMQ-G2FLS
D913 VHDFMQG2FLS-1 AN N J Diode FMQ-G2FLS
D914 RH-DXA062WJZZY AE J Diode SHV-04V6
E701 LANGQA017WJFW AG J Fixing Metal
! F701 QFS-CA010WJZZ AF J Fuse T6.3AH/AC250V
! F705 QFS-TA005WJZZ AG J Thermal Fuse 127°C
FB701 RBLN-0094CEZZY AC J Ferrite Bead BLN-0094CE
FB702 RBLN-0094CEZZY AC J Ferrite Bead BLN-0094CE
FB704 RBLN-A007WJZZY AC J Ferrite Bead BLN-A007WJ
FB707 RBLN-0020CEZZ+ AB J Ferrite Bead BLN-0020CE
FH701 QFSHD1013CEZZ+ AC J Fuse Holder
FH702 QFSHD1014CEZZ+ AC J Fuse Holder
IC702 VHiTA78M12S-1 AG J IC TA78M12S(Q)
IC703 VHiSTRW67652E AL J IC STR-W6765N
IC704 VHiHA17431U-1Y AE J IC HA17431UA-TL-E
IC902 VHiFA5501AN-1Y AQ N J IC FA55501AN-D1-TE1
L701 RCiLPA137WJZZ AF J Coil
! L702 RCiLFA178WJZZ AK J Coil
! L703 RCiLFA178WJZZ AK J Coil
L705 RCiLPA546WJZZ AH J Coil
L901 RCiLCA126WJZZ AQ N J Coil
L902 RCiLPA475WJZZ AK J Coil
! P701 QPLGAA004WJZZ AH J AC Plug
! P702 QPLGN0269GEZZ AB J Plug 2Pin(BA)
P704 QCNCMA114WJZZ AF J Connector 14Pin
Q702 VS2SK3451++-1 AS N J Transistor 2SK3451-01MR-F119
Q704 VS2SK3451++-1 AS N J Transistor 2SK3451-01MR-F119
Q705 VS2SA1797Q+-1Y AD J Transistor 2SA1797 T100 Q
Q901 VS2SK2699++-1 AR J Transistor 2SK2699(SHARP,F)
Q904 VS2SA2056++-1Y AE J Transistor 2SA2056(TE85L,F)
Q905 VS2SK3525++-1 AM J Transistor 2SK3525-01MR-F119
! R701 RR-HZ0119CEZZY AC J High Voltage High Resistor
R703 VRS-TQ2BD474FY AA J Resistor 470k 1/8W Metal Oxide
R706 VRN-TV1JD684DY AB N J Resistor 680k 1/16W Metal Film
R710 VRN-CY1JF133DY AB J Resistor 13k 1/16W Metal Film
R714 VRD-RM2HD102JY AA J Resistor 1k 1/2W Carbon
R716 VRS-SV2HC100JY AB J Resistor 10 1/2W Metal Oxide
R717 RMPTKA001WJZZ AH J Packaged circuit
R724 RR-WZA012WJZZ AE J Resistor 0.15 5W Resistor Wire
R727 RR-WZA012WJZZ AE J Resistor 0.15 5W Resistor Wire
R730 VRS-TV1JD103JY AA J Resistor 10k 1/16W Metal Oxide
R733 VRS-TQ2BD153JY AA J Resistor 15k 1/8W Metal Oxide
R734 VRD-RM2HD221JY AA J Resistor 220 1/2W Carbon
R735 VRS-TQ2BD101JY AA J Resistor 100 1/8W Metal Oxide
14
RANK MARK DELIVERY

R739 VRN-VV3AB3R9J AA J Resistor 3.9 1W Metal Film
R743 VRS-TQ2BD332FY AA J Resistor 3.3k 1/8W Metal Oxide
R744 VRS-VV3AB273J AA J Resistor 27k 1W Metal Oxide
R745 VRS-VV3AB273J AA J Resistor 27k 1W Metal Oxide
R746 VRS-VV3DB220J AA J Resistor 22 2W Metal Oxide
R751 VRS-TV1JD222FY AA J Resistor 2.2k 1/16W Metal Oxide
R754 VRS-TQ2BD331FY AA J Resistor 330 1/8W Metal Oxide
R755 VRS-TV1JD272FY AA J Resistor 2.7k 1/16W Metal Oxide
R756 VRS-TV1JD681FY AA N J Resistor 680 1/16W Metal Oxide
R757 VRS-TQ2EF221JY AA N J Resistor 220 1/4W Metal Oxide
R766 VRN-VV3ABR22J AA J Resistor 0.22 1W Metal Film
R901 VRS-TV1JD334FY AA J Resistor 330k 1/16W Metal Oxide
R905 RR-FZA002WJZZ AE J Resistor 0.05 3W Metal Plate Resistor
R907 VRS-TQ2BD100FY AA J Resistor 10 1/8W Metal Oxide
R912 VRS-TQ2BD000JY AA J Resistor 0 1/8W Metal Oxide
R920 VRS-TQ2EF100FY AA N J Resistor 10 1/4W Metal Oxide
R937 VRS-VV3DB273J AA J Resistor 27k 2W Metal Oxide
RDA701 PRDARA225WJFW AF N J Heat Sink
RDA901 PRDARA224WJFW AG J Heat Sink
! RY701 RRLYDA008WJZZ AG J Relay
T704 RCiLCA175WJZZ AY N J Coil
! T705 RTRNWA242WJZZ AL J Transformer
T901 RTRNZA102WJZZ AH J Transformer
T903 RTRNWA197WJZZ AL N J Transformer
TH901 RH-HXA020WJZZ AK J Thermister
! VA701 RH-VXA018WJZZ AD J Varistor
N LX-BZ3049GEFN AB J Screw
N LX-BZ3049GEFN AB J Screw
N LX-BZA044WJFU AA J Screw
N PSPAZB157WJZZ AE N J Spacer
15
RANK MARK DELIVERY
[6] DUNTKD148WEF4 (BALLAST CONTROL Unit)

C7706 VCKYCY1EB104KY AB J Capacitor 0.1 25V Ceramic
C7727 VCKYTV1CF105ZY AB J Capacitor 1 16V Ceramic
C7730 VCKYTV1CB105KY AC J Capacitor 1 16V Ceramic
C7734 VCKYTV1CB105KY AC J Capacitor 1 16V Ceramic
C7744 RC-KZA110WJZZY AD J Capacitor 10 25V Ceramic
D7701 RH-EX1398CEZZY AB J Zener Diode UDZSTE-178.2B
D7704 RH-EX1398CEZZY AB J Zener Diode UDZSTE-178.2B
! D7713 RH-FXA005WJZZY AD J Diode PC123ZY8J00F
IC7701 VHiM51995AF-1Y AM J IC M51995AFPCF0J
IC7704 VHiTA78L05F-1Y AE J IC TA78L05F(TE12L,F)
IC7705 VHiBD4742G+-1Y AD J IC BD4742G-TR
IC7707 RH-iXB932WJZZQ AX N J IC iXB932WJ
IC7709 VHiNJM2902V-1Y AD J IC NJM2902V(TE1)
P7701 QPLGN0864TAZZY AE J Plug 8Pin
Q7701 VSDTA114EKA-1Y AB J Transistor DTA114EKAT146
Q7702 VSDTC114EKA-1Y AB J Transistor DTC114EKAT146
Q7703 VS2SC2712Y/-1Y AB J Transistor 2SC2712-Y(TE-85L)
Q7708 VS2SA1162Y/-1Y AB J Transistor 2SA1162-Y(T5L,F,T)
R7702 VRS-TV1JD331JY AB J Resistor 330 1/16W Metal Oxide
16
RANK MARK DELIVERY
[6] DUNTKD148WEF4 (BALLAST CONTROL Unit)

R7715 VRS-TV1JD1R0JY AA J Resistor 1 1/16W Metal Oxide
R7724 VRN-CY1JF153DY AA J Resistor 15k 1/16W Metal Film
R7728 RVR-M4555CEZZY AC J Variable Resistor
R7732 VRN-CY1JF682DY AB J Resistor 6.8k 1/16W Metal Film
R7752 VRS-TQ2BD4R7JY AA J Resistor 4.7 1/8W Metal Oxide
R7753 VRS-TQ2BD4R7JY AA J Resistor 4.7 1/8W Metal Oxide
X7701 RCRMCA019WJZZY AF J Ceramic Vibrator
17
RANK MARK DELIVERY
[7] DUNTKD164WEF4 (R/C RECEIVER Unit)

C1122 VCEAPF1CW107MY AC J Capacitor 100 16V Electrolytic
P1121 QPLGN0364TAZZY AC J Plug 3Pin(RC)
RMC1121 RRMCUA027WJZZ AK J Remote Receiver
N LHLDPA022WJZZ AD N J Holder
N QCNW-D517WJQZ AE J Connecting Cord
18
[8] CABINET AND MECHANICAL PARTS
47
48
17 14
29
1-3
1
24 17
1-2 1-4 23
35
8-2
1-1
8 17
8-1
33
45
11-3
17 11-2
17 17
25
43
30
11 26
11-1
46
31
15
43
13
31
21 39
31
42 21
43
43
2-2-3
43
2-2-4
2-2
2
2-9 41
20
2-2-2
2-11
2-10 2-2-1
36 4
2-8
2-6
47
2-8-1
43 2-1
49 2-8-2
5 2-3
2-1-4
2-1-3
2-7
9
2-5
2-1-1 2-4 2-7-1 2-7-2
44 12
2-1-2
19

RANK MARK DELIVERY
[8] CABINET AND MECHANICAL PARTS

1 DBDYTA194WEF0 BD N J Top Body Ass'y (10X-L)
1 DBDYTA195WEF0 BD N J Top Body Ass'y (MB50X-L)
1 DBDYTA196WEF0 BE N J Top Body Ass'y (11XC-L)
1 DBDYTA197WEF0 BE N J Top Body Ass'y (HB007X-L)
1 DBDYTA198WEF0 BE N J Top Body Ass'y (10S-L)
1-1 Not Available - N - Top Body
1-2 HDECPA027WJSA AD J Led Cover
1-3 HiNDPB309WJSA AH J Operation Cover (10S-L)
1-3 HiNDPB309WJSB AH J Operation Cover (10X-L/11XC-L)
1-3 HiNDPB309WJSC AH J Operation Cover (MB50X-L/HB007X-L)
1-4 JBTN-A463WJSA AF J Power Button
2 Not Available - N - Bottom Body Ass'y
2-1 CDORUA064WEF0 AQ N J Lamp Door Ass'y
2-1-1 Not Available - N - Lamp Door
2-1-2 LX-BZ3274CEFN AE J Screw
2-1-3 XRESJ30-06000 AA J E-Ring
2-1-4 PSLDHA042WJFW AF J Shield
2-2 DBDYUA234WEF0 BM N J Bottom Body Ass'y (10X-L)
2-2 DBDYUA235WEF0 BM N J Bottom Body Ass'y (MB50X-L)
2-2 DBDYUA236WEF0 BM N J Bottom Body Ass'y (11XC-L)
2-2 DBDYUA237WEF0 BM N J Bottom Body Ass'y (HB007X-L)
2-2 DBDYUA238WEF0 BM N J Bottom Body Ass'y (10S-L)
2-2-1 Not Available - N - Bottom Body
2-2-2 LX-NZ3120CEFW AB J Nut, x1
2-2-3 LX-NZ3144CEFW AC J Nut, x5
2-2-4 LHLDWA161WJZZ AD N J Wire Holder
2-3 GLEGPA030WJSA AK J Rear Adjuster
2-4 GLEGPA036WJSA AP J Front Adjuster
2-5 HDECPA028WJSA AE J R/C Cover
2-6 XEBSN30P08000 AA J Screw (Front Adjuster)
2-7 Not Available - - Filter Ass'y (Front)
2-7-1 LHLDZA781WJKA AF J Filter Holder (Front)
2-7-2 PFiLDA025WJZZ AK J Filter
2-8 Not Available - - Filter Ass'y (Rear)
2-8-1 LHLDZA782WJKA AF J Filter Holder (Rear)
2-8-2 PFiLDA025WJZZ AK J Filter
2-9 LX-HZ3105CEFN AB J Screw
2-10 MLEVPA036WJK0 AF N J SW lLever
2-11 QCNW-E821WJQZ AN N J LF Wire
4 ----- - - Refer to Optical Mechanism Parts
5 AN-XR10L2 - J Lamp Unit
8 DSETUD147FMG1 BZ N J BALLAST POWER Ass'y (with Ballast Control Unit)
8-1 Not Available - N - BALLAST POWER Unit
8-2 DUNTKD148WEF4 BE N J BALLAST CONTROL Unit
9 DUNTKD164WEF4 AN N J R/C RECEIVER Unit
11 DUNTKE004FMF0 CN J MAIN Unit (10S-L)
11 DUNTKE004FMF1 CN N J MAIN Unit (10X-L/11XC-L/MB50X-L/HB007X-L)
11-1 PSLDMA722WJFW AL J Shield
11-2 PSLDMA726WJFW AF J MAIN PWB Shield
11-3 PSPAZA913WJKZ AB J Shield Spacer
12 HINDPC073WJZZ AC N J PSB Label (10X-LK)
12 HINDPC074WJZZ AG N J PSB Label (10S-LK)
13 LHLDZA579WJKZ AH J Speaker Holder
14 LHLDZA580WJKZ AD J Suport, x2
15 LHLDZA590WJKZ AD J PWB Suport
17 LX-BZ3100CEF7 AA J Screw, x11
20 NFANRA070WJ00 AY J Exhaust Fan (Lamp)
21 NFANRA069WJ00 AT J Exhaust Fan (Power) , x2
23 PCOVNA008WJZZ AE J Power Unit Duct B
24 PCOVNA009WJZZ AE J Power Unit Duct C
25 PCOVWA004WJKZ AH J Power Insulator (Front)
26 PCOVWA005WJKZ AH J Power Insulator (Rear)
29 PSLDMA720WJFW AM J Ballast Shield (Upper)
30 PSLDMA721WJFW AV J Ballast Shield (Lower)
31 PSPAGA276WJZZ AP J Fan Rubber, X3
33 PZETKA128WJKZ AN J Power Insulator Bottom
35 QCNW-D518WJQZ AM J EA Wire
36 QCNW-D575WJPZ AR J Baimetal Wire
39 RSP-ZA085WJQZ AP J Speaker
41 XBBSN30P08000 AA J Screw, x1
42 XBPS830P08JS0 AB J Screw, x2
43 XEBSN30P12000 AA J Screw, x19
44 TLABZA956WJZZ AB J WEEE Mark Label (10S-LE/K, 10X-LE/K)
45 Not Available - - Shaft
46 RH-HXA025WJPZ AP J Thermistor
47 LHLDW1226CEZZ AC J Wire Holder, x2
48 PSPAZA875WJKZ AC J Spacer, x2
20
4-6
4-2
4-11
4-20
4-21
18 27 16
19 4-29
4-31
32 28 37 4-29
6
38 4-34
18 4-35
4-10
4-29 4-29
4-22 4-1 4-9
19 4-15
4-29
40
4-29
4-31
4-25
4-16 4-27
4-29
4-7 4-18 3
22 4-17 4-31
40
4-24
4-4
4-3
4-29 7 4-19
4-5-4 4-8
4-12 4
4-23
4-26
4-5 4-5-2
4-5-1
4-29 4-5-3
4-30
4-32
40
4-13
21

RANK MARK DELIVERY

3 CCAPHA024WJSA AG J Lens Cap Ass'y
4 CCHSKA019WEFB CG N J Optical Mechanism Unit
4-1 LCHSKA019WJF1 BG J Engine Base
4-2 LHLDZA572WJKZ AH J Mirror Holder
4-3 LHLDZA573WJKZ AK J Rod Holder Base
4-4 LHLDZA574WJKZ AH J Rod Holder Cover
4-5 CFiLWA097WEF0 BU J Colour Wheel Ass'y
4-5-1 PFiLWA097WJZZ BT J Colour Wheel
4-5-2 LHLDZA817WJFW AP J C/W Holder
4-5-3 PSHEGA043WJKZ AF J Sheet
4-5-4 XBBS920P05000 AB J Screw for C/W, x3
4-6 MSPRCA062WJFJ AB J Spring
4-7 MSPRPA061WJFW AE J Plastic Lens Spring
4-8 MSPRPA070WJFW AC J Rod Spring, x2
4-9 PCOVPA028WJSA AN J Focus Ring
4-10 PCOVPA029WJSA AM J Zoom Ring
4-11 PCOVZA056WJFW AF J Engine Cover
4-12 PCOVZA085WJKZ BA N J Lamp House
4-13 PDUC-A064WJKZ AR J Exhaust Duct
4-15 PLNS-A055WJZZ BV J Projection Lens
4-16 PLNS-A056WJZZ AX J Plastic Lens
4-17 PLNS-A057WJZZ AR J Illmi Lens 1
4-18 PLNS-A058WJZZ AS J Illmi Lens 2
4-19 PLNS-A059WJZZ BF J Rod
4-20 PMiR-A071WJZZ AS J Refrect Mirror
4-21 PSLDPA036WJFW AF J Projection Lens Aperture
4-22 PSLDPA061WJFW AG J DMD Aperture
4-23 PSLDPA038WJFW AD J Rod Aperture
4-24 PSLDPA039WJFW AF J Illmi Aperture 1
4-25 PSLDPA057WJFW AG J Illmi Aperture 2
4-26 PSLDPA042WJFW AE J House Shading board
4-27 PSPAZA769WJZZ AF J Dust Proof Spacer
4-29 XBBSN30P06000 AA J Screw M3*6, x13
4-30 XBBSN30P10000 AA J Screw for C/W Holder, x2
4-31 XBPS830P08JS0 AB J Screw, Pj Lns=4, Mir=2
4-32 XEBSN30P08000 AA J Screw for Duct1
4-34 TLABZB026WJZZ AE J MECHA No.LABEL
4-35 TLABZB027WJZZ AB J OPT MODEL LABEL
6 DUNTKD140WEF0 BT N J DMD Unit
7 DUNTKD141WEF4 AP N J PHOTO SENSOR Unit
16 LHLDZA612WJFW AL J Backer Plate
18 LX-BZA110WJF7 AC J DMD Screw, x4
19 MSPRCA062WJFJ AB J Spring For DMD, x4
22 NFANSA019WJZZ BB J Blower Fan Unit
27 PRDARA223WJFW AV J DMD Heat Sink
28 PSHEGA040WJZZ AE J Thermal Pad
32 PSPAZA768WJZZ AD J Backer Plate Sheet
37 QSOCZA105WJZZ AZ J DMD Socket (10X-L/11XC-L/MB50X-L/HB007X-L)
37 QSOCZA106WJZZ AZ J DMD Socket (10S-L)
38 RDMDPA013WJZZQ CY J DMD SVGA (10S-L)
38 RDMDPA027WJZZ CW N J 0.55 DMD XGA (10X-L/11XC-L/MB50X-L/HB007X-L)
22
[10] SUPPLIED ACCESSORIES
X4
X3
X1
X2
X15
X14
X10 X12 X16 X7 X9

X11 X13 X17 X8 X18
X5 X6

RANK MARK DELIVERY
[10] SUPPLIED ACCESSORIES

X1 RRMCGA398WJSA AS J Remote Control unit
! X2 QACCBA036WJPZ AX J AC Cord for U.K and Singapore
! X2 QACCDA007WJPZ AR J AC Cord for USA and Canada
! X2 QACCLA018WJPZ AU J AC Cord for Australia, New Zealand and Oceania
! X2 QACCVA011WJPZ AT J AC Cord for Europe except U.K
X3 QCNWGA045WJPZ AU J RGB Cable
X4 QCNWGA043WJPZ AW J 3 RCA to 15-pin D-sub cable (10X-LU/11XC-L for USA)
X5 TiNS-C689WJZZ AL N J Operation Manual (10X-L/10S-L)
X5 TiNS-C690WJZZ AM N J Operation Manual (11XC-L/MB50X-L)
X5 TiNS-C691WJZZ AH N J Operation Manual (HB007X-L)
X6 UDSKAA083WJZZ AL N J CD-ROM (10X-L/10S-L)
X7 TGAN-A232WJZZ AC N J SEC ER Information (for USA)
X8 TGAN-A233WJZZ AC N J SECL ER Infomation (for Canada)
X9 TGAN-A318WJZZ AD N J SECL Warranty (for Canada)
X10 TGAN-A678WJZZ AB N J SEC Warranty (10X-L/10S-L/11XC-L)
X10 TGAN-A757WJZZ AB N J SEC Warranty (MB50X-L)
X11 TLABZA255WJZZ AE J ER Sticker (for USA and Canada)
X12 SSAKA0160CEZZ AB J Polyethyrene Bag
X13 TCAUZA143WJZZ AA J System lock Caution
X14 QCNWGA015WJPZ AK J DIN-D-sub RS-232C adaptor (MB50X-L)
X15 CCAPHA024WJSA AG J Lens Cap Ass'y
X16 TCAUZA201WJZZ AB N J Caution 3 RCA to 15-pin D-sub cable (10X-LU)
X17 TCAUZA187WJZZ AC J WEEE Caution Sheet (10X-L/10S-L for Europe and HB007X-L)
X18 GCASNA019WJZZ AZ J Strage Case (11XC-L)
23
[11] PACKING PARTS (NOT REPLACEMENT ITEM)
S2
S6
S3
S4
S7
S5
S7 S1
24

RANK MARK DELIVERY
[11] PACKING PARTS (NOT REPLACEMENT ITEM)

S1 SPAKCC964WJZZ - N - Packing Case (10X-LU)
S1 SPAKCC965WJZZ - N - Packing Case (MB50X-L)
S1 SPAKCC966WJZZ - N - Packing Case (11XC-L)
S1 SPAKCC967WJZZ - N - Packing Case (HB007X-L)
S1 SPAKCC968WJZZ - N - Packing Case (10S-LU)
S1 SPAKCD002WJZZ - N - Packing Case (10X-LE/10X-LK)
S1 SPAKCD003WJZZ - N - Packing Case (10S-LE/10S-LK)
S2 SPAKFA792WJZZ - - Accessory Case
S3 SPAKPA360WJZZ - - Wrapping Paper
S4 SPAKXA768WJZZ - - Buffer Material
S5 TLABVA333WJZZ - - Bar Code Label (for USA, Canada, Australia, New Zealand and Oceania)
S6 TLABZA610WJZZ - - Recycle Label (for Europe except U.K)
S7 TLABZA957WJZZ - - C.W.Mark, x2 (for Europe and Singapore)
[12] SERVICE JIGS AND EQUIPMENT(USE FOR SERVICING)
N QCNW-C516WJQZ AG J Extension Cable, 3pins L=200mm, Main to Fan, x2
N QCNWKA006WJZZ AX J Extension Cable, 4pins L=500mm, Main to Fan
N QCNWKA008WJZZ AP J Extension Cable, 14pins, Main to Power
N QCNWKA009WJZZ DA J Extension Cable, 140pins, Main to DMD
N RUNTZA018WJZZ DR J Adjustment Jig, for the Ballast Unit
N QCNWKA016WJZZ AU N J Extension Cable, 3 to 2pins L=600mm, Adjustment Jig to Lamp
N DBDYTA132WJZZ BS J Service Top Body (UV light protection cover)
25
2006 BY SHARP CORPORATION

COPYRIGHT © 2005
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying , recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Dec. 2006 Printed in Japan CS Promotion Center
TQ2072-S YT. DS Yaita,Tochigi 329-2193, Japan

Service Manual: Multimedia Projector

Uploaded by

Copyright:

Available Formats

Service Manual: Multimedia Projector

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Multimedia Projector

Uploaded by

Copyright:

Available Formats

TopPage

CHAPTER 4. ELECTRICAL ADJUSTMENT Parts Guide

This document has been published to be used for

IMPORTANT SERVICE SAFETY NOTES

IMPORTANT SERVICE SAFETY NOTES (for USA)

PRECAUTIONS A PRENDRE LORS DE LA REPARATION

AUX PIECES BRANCHER A UNE

NOTE TO SERVICE NOTE POUR LE PERSONNEL

1. Toujours porter des lunettes de soleil lors d’un entretien

2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier

3. Ne pas faire fonctionner plus de 2 heures avec le coffret

Précautions pour les radiations UV

To illuminate the lamp in the unit with Top Body

CAUTION The lighting flash with arrowhead within a

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER

ATTENTION L’éclair terminé d’une flèche à l’intérieur

Employing lead-free solder

Using lead-free wire solder

ZHNDAi123250E J φ0.3mm 250g(1roll) BL

Product type Projector

Part Names and Functions

Focus ring Zoom ring

Using the Kensington Lock

STANDBY button ON button

AV MUTE button AUTO SYNC button

Inserting the Batteries

2 Insert the batteries.

3 Attach the cover and slide it until it clicks into place.

AUDIO (INPUT 1, 2) terminal AUDIO (INPUT 3, 4) terminal

AUDIO OUTPUT terminal

Connecting Pin Assignments

COMPUTER-RGB/COMPONENT INPUT1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals:

Units: inches (mm)

2 7/8 (73) 1 55/64 (47)

3 5/32 (80) 3 1/16 (77.5)

2 61/64 1 53/64 2 19/32

Regarding the Lamp

IMPORTANT NOTE TO U.S. CUSTOMERS:

Caution Concerning the Lamp

Replacing the Lamp

Removing and Installing the

1 Press STANDBY/ON on the pro-

2 Disconnect the power cord.

Regarding the Lamp (Continued)

lamp unit. Hold the lamp unit by the

5 Insert the new lamp unit.

6 Replace the lamp unit cover.

Resetting the Lamp Timer

[1] Removing the lamp door and the lamp unit

[2] Removing the top body

POWER SUPPLY BALLAST Unit

Fans for power supply 4-4 4-7

Optical Mechanism Unit

RC Light Receiver PWB

DMD PWB Unit Optical Mechanism Unit

[1] THE OPTICAL UNIT OUTLINE

Tightening order: → → → Fig. 1

When mounting DMD, tighten the 4 screws evenly.

Employing lead-free solder

Using lead-free wire solder