Clamp Multimeter: User's Manual

 CLAMP MULTIMETER
F205
EN G L I S H User’s manual
Clamp Multimeter F205 English
CONTENTS
1 PRESENTATION ........................................................................................................ 8
1.1 THE SWITCH .....................................................................................................................9
1.2 THE KEYS OF THE KEYPAD .......................................................................................10
1.3 THE DISPLAY UNIT.......................................................................................................11
1.3.1 The symbols of the display unit .................................................................... 11
1.3.2 Measurement capacity exceeded (O.L) ........................................................ 13
1.4 THE TERMINALS ...........................................................................................................13
2 THE KEYS ................................................................................................................. 13
2.1 KEY ....................................................................................................................................13

2.2 KEY (SECOND FUNCTION) ..................................................................................................14
2.3 KEY ....................................................................................................................................15
2.4 KEY ....................................................................................................................................15
2.4.1 In the normal mode ...................................................................................... 15
2.4.2 The MAX/MIN/PEAK mode + activation of the HOLD mode...................... 16
2.4.3 Access to the True-INRUSH mode ( set to ) ................................. 17
2.5 KEY ....................................................................................................................................17
2.5.1 The Hz function in the normal model ........................................................... 17
2.5.2 The Hz function + activation of the HOLD mode ........................................ 18
2.6 KEY ....................................................................................................................................18
3 USE ............................................................................................................................. 19
3.1 COMMISSIONING ..........................................................................................................19
3.2 STARTING UP THE CLAMP MULTIMETER ............................................................20
3.3 SWITCHING THE CLAMP MULTIMETER................................................................20
3.4 CONFIGURATION..........................................................................................................20
3.4.1 Programming of the maximum resistance allowed for a continuity ............. 21
3.4.2 De-activation of automatic switching off (Auto Power OFF) ...................... 21
3.4.3 Programming of the current threshold for the True INRUSH measurement 21
3.4.4 Default configuration ................................................................................... 22
3.5 VOLTAGE MEASUREMENT (V).................................................................................22
3.6 CONTINUITY TEST .................................................................................................23
3.6.1 Automatic compensation of the resistance of the leads ................................ 24
3.7 RESISTANCE MEASUREMENT Ω..............................................................................24
3.8 DIODE TEST .............................................................................................................25
3.9 CURRENT MEASUREMENT (A) .................................................................................25
3.9.1 AC measurement .......................................................................................... 25
3.9.2 DC or AC+DC measurement ....................................................................... 26
3.10 STARTING CURRENT OR OVERCURRENT (TRUE INRUSH) MEASUREMENT
27
2
English Clamp Multimeter F205
3.11 POWER MEASUREMENTS W, VA, VAR AND PF .....................................................27

3.11.1 Measurement of single-phase power ............................................................ 28
3.11.2 Balanced three-phase power measurement .................................................. 28
3.12 “DIRECTION OF ROTATION OF THE PHASES” OR “ORDER OF THE PHASES”
MODE ..................................................................................................................................29
3.13 FREQUENCY MEASUREMENT (HZ) .........................................................................30
3.13.1 Frequency measurement in voltage.............................................................. 30
3.13.2 Frequency measurement in current.............................................................. 31
3.13.3 Measurement of frequency in power ............................................................ 31
3.14 MEASUREMENT OF THE LEVEL OF HARMONICS (THD) AND OF THE
FREQUENCY OF THE FUNDAMENTAL (NETWORK) .......................................................31
3.14.1 Measurement of the THD and of the frequency of the fundamental in voltage
32
3.14.2 Measurement of the THD and of the frequency of the fundamental in current
32
4 CHARACTERISTICS............................................................................................... 34
4.1 REFERENCE CONDITIONS .........................................................................................34
4.2 CHARACTERISTICS UNDER THE REFERENCE CONDITIONS..........................34
4.2.1 DC voltage measurement ............................................................................. 34
4.2.2 AC voltage measurement ............................................................................. 35
4.2.3 AC+DC voltage measurement ..................................................................... 36
4.2.4 DC current measurement ............................................................................. 36
4.2.5 AC current measurement ............................................................................. 37
4.2.6 AC+DC intensity measurement.................................................................... 37
4.2.7 True-Inrush measurement ............................................................................ 38
4.2.8 Continuity measurement .............................................................................. 38
4.2.9 Resistance measurement .............................................................................. 38
4.2.10 Diode test ..................................................................................................... 39
4.2.11 Active DC power measurements .................................................................. 39
4.2.12 Active AC power measurements ................................................................... 40
4.2.13 Active AC+DC power measurements........................................................... 41
4.2.14 Measurement of apparent AC power ........................................................... 42
4.2.15 Measurement of apparent AC+DC power ................................................... 42
4.2.16 Measurement of reactive AC power ............................................................. 43
4.2.17 Measurement of reactive AC+DC power ..................................................... 43
4.2.18 Calculation of the power factor ................................................................... 44
4.2.19 Frequency measurements............................................................................. 45
4.2.20 Characteristics in THDr .............................................................................. 45
4.2.21 Characteristics in THDf ............................................................................... 45
4.2.22 Indication of order of the phases ................................................................. 46
4.3 ENVIRONMENTAL CONDITIONS .............................................................................46
4.4 CHARACTERISTICS OF CONSTRUCTION ..............................................................47
4.5 POWER SUPPLY .............................................................................................................47
4.6 COMPLIANCE WITH INTERNATIONAL STANDARDS .......................................47
3
4.7 VARIATIONS IN THE DOMAIN OF USE ...................................................................48

5 MAINTENANCE....................................................................................................... 49
5.1 CLEANING .......................................................................................................................49
5.2 REPLACEMENT OF THE BATTERY...........................................................................49
5.3 METROLOGICAL CHECK ............................................................................................49
5.4 REPAIR .............................................................................................................................49
6 WARRANTY ............................................................................................................. 50
7 DELIVERY CONDITION ........................................................................................ 50
4
You have just acquired an F205 clamp multimeter and we thank you.
For best results from your device :

• read this user manual attentively,
• observe the precautions for its use.
Meanings of the s ymbols us ed on the devic e

Danger. The operator agrees to refer to this data sheet whenever this danger
symbol is encountered.
Application or withdrawal authorized on uninsulated or bare conductors at

dangerous voltages.
9 V battery.
The CE marking indicates compliance with European directives.
Double insulation or reinforced insulation.
Selective sorting of wastes for the recycling of electrical and electronic

equipment within the European Union.
In conformity with directive DEEE 2002/96/EC: this equipment must not be
treated as household waste.
AC – Alternating current.
AC and DC – Alternating and direct current.
Earth.
Risk of electric shock.
5
PRECAUTIONS FOR USE
This device complies with safety standards IEC-61010-1 and 61010-2-032 for
voltages of 1000V in category III or 600V in category IV at an altitude OF less than
2000m, indoors, with a degree of pollution not exceeding 2.
These safety instructions are intended to ensure the safety of persons and proper
operation of the device. If the tester is used other than as specified in this data
sheet, the protection provided by the device may be impaired.
 The operator and/or the responsible authority must carefully read and clearly
understand the various precautions to be taken in use.
 If you use this instrument other than as specified, the protection it provides
may be compromised, thereby endangering you.
 Do not use the instrument in an explosive atmosphere or in the presence of
flammable gases or fumes.
 Do not use the instrument on networks of which the voltage or category
exceeds those mentioned.
 Do not exceed the rated maximum voltages and currents between terminals
or with respect to earth.
 Do not use the instrument if it appears to be damaged, incomplete, or not
properly closed.
 Before each use, check the condition of the insulation on the leads, housing,
and accessories. Any element of which the insulation is deteriorated (even
partially) must be set aside for repair or scrapped.
 Use leads and accessories rated for voltages and categories at least equal to
those of the instrument. If not, an accessory of a lower category lowers the
category of the combined Clamp + accessory to that of the accessory.
 Observe the environmental conditions of use.
 Do not modify the instrument and do not replace components with
"equivalents". Repairs and adjustments must be done by approved qualified
personnel.
 Replace the battery as soon as the symbol appears on the display unit.
Disconnect all cords before opening the battery compartment cover.
 Use personal protective equipment when conditions require.
 Keep your hands away from the unused terminals of the instrument.
6
 When handling the test probes, crocodile clips, and clamp ammeters, keep
your fingers behind the physical guard.
 As a safety measure, and to avoid repeated overloads on the inputs of the
device, we recommend performing configuration operations only when the
device is disconnected from all dangerous voltages.
MEASUREMENT CATEGORIES
Definitions of the measurement categories :
CAT II: Circuits directly connected to the low-voltage installation.

Example: power supply to household electrical appliances and portable tools.
CAT III: Power supply circuits in the installation of the building.

Example: distribution panel, circuit-breakers, fixed industrial machines or devices.
CAT IV: Circuits supplying the low-voltage installation of the building.

Example: power lines, meters, and protection devices.
7
1 PRESENTATION
The F205 is a professional electrical measuring instrument that combines the
following functions:
 Current measurement;
 Measurement of inrush current / overcurrent (True-Inrush);
 Voltage measurement;
 Frequency measurement;
 Measurement of level of harmonics (THD)
 Continuity test with buzzer;
 Resistance measurement;
 Diode test;
 Power measurements (W, VA, var and PF);
 Indication of the order of the phases.
1
Item Designation See §
Jaws with centring marks 3.5 to

1
(see connection principles) 3.14
2
2 Physical guard -
3 3 Switch 1.1
7
4 Function keys 2
4 5 Display unit 1.3

6 Terminals 1.4
7 Trigger -
5
Figure 1 : the F205 clamp multimeter
8
1.1 THE SWITCH

The switch has six positions. To access the , , , , , functions,
set the switch to the desired function. Each setting is confirmed by an audible
signal. The functions are described in the table below.
6
Figure 2 : the switch
Item Function See §

1 OFF mode – Switches the clamp multimeter off 3.3
2 AC, DC, AC+DC voltage measurement (V) 3.5
3 Continuity test 3.6
Resistance measurement Ω 3.7
Diode test 3.8
4 AC, DC, AC+DC current measurement (A) 3.9
5 Power measurements (W, var, VA) and calculation of the
3.11
power factor (PF) AC, DC, AC+DC
6 Indicator of the order of the phases 3.12
9
1.2 THE KEYS OF THE KEYPAD

Here are the six keys of the keypad :
1 2 3
4 5 6
Figure 3 : the keys of the keypad

1 Storage of values, disabling of display 2.1
Zero correction ADC/AAC+DC/WDC/WAC+DC 3.9.2
Compensation of the resistance of the leads in the 3.6.1
continuity and ohmmeter function
2 Selection of the type of measurement (AC, DC, AC+DC)
2.2
Selection of single-phase or three-phase measurement
3 Activation or de-activation of the backlighting
2.3
of the display unit
4 Activation or de-activation of the MAX/MIN/PEAK mode
2.4
Activation or de-activation of the INRUSH mode in A
5 Measurements of frequency (Hz), of the level of harmonics
(THD) 2.5
Display of the powers W, VA, var and PF
6 Activation of the ΔREL mode – Display of relative and
2.6
differential values
10
1.3 THE DISPLAY UNIT

Here is the display unit of the clamp multimeter:
7 6
1
3
4
Figure 4 : the display unit

1 Display of the modes selected (keys) 2
2 Display of the measurement value and unit 3.5 to 3.12
3 Display of the MAX/MIN/PEAK modes 2.4
4 Type of measurement (AC or DC) 2.2
5 Total three-phase power measurements 3.11.2
6 Display of the selected modes (switch) 3.5
7 Spent battery indication 5.2
1.3.1 The symbols of the display unit
Symbol Designation
AC Alternating current or voltage
DC Direct current or voltage
AC+DC Alternating and direct current or voltage
∆REL Relative value, with respect to a reference
∆Ref Reference value
11
Storage of the values and hold of the display
Max Maximum RMS value
Min Minimum RMS value
Peak+ Maximum peak value
Peak- Minimum peak value
Balanced total three-phase power measurement
V Volt
Hz Hertz
W Watt
A Ampere
% Percentage
Ω Ohm
m Milli- prefix
k Kilo- prefix
var Reactive power
VA Apparent power
PF Power factor
THDf Total harmonic distortion with respect to the fundamental
Total harmonic distortion with respect to the true RMS

THDr
value of the signal.
Indicator of order to the phases
Compensation of the resistance of the leads
Continuity test
Diode test
Permanent display (automatic switching off de-activated)
Spent battery indicator
The display of “rdy”, for “ready”, indicates that the device is ready (“Indicator of
order of the phases” function).
12
1.3.2 Measurement capacity exceeded (O.L)

The O.L (Over Load) symbol is displayed when the display capacity is exceeded.
1.4 THE TERMINALS

The terminals are used as follows:
Item Function
1 Cold terminal (COM)
2 Hot terminal (+)
1 2
Figure 5 : the terminals
2 THE KEYS
The keys of the keypad respond differently to short, long, and sustained presses.
The , and keys provide new functions and allow the detection and
acquisition of parameters complementary to the usual elementary measurements.
- Each of these keys can be used independently of the others or in perfect
complementarity with them: this makes navigation simple and intuitive for
looking up all measurement results.
- It is possible, for example, to look up in turn the MAX, MIN, etc. values of the
RMS voltage alone, or else look up in turn all of the MAX (or MIN, or PEAK)
values of all power results (W, VA, var, etc.).
In this section, the icon represents the possible positions of the switch for which
the key concerned has some action.
2.1 KEY
This key is used to:
 store and look up the last values acquired specific to each function (V, A, Ω,
T°) according to the specific modes previously activated (MAX/MIN); the
present display is then maintained while the detection and acquisition of new
values continues;
13
 perform automatic compensation of the resistance of the leads (see also §

3.6.1) ;
 perform an automatic zero correction in ADC/AC+DC et W DC/AC+DC (see also §
3.9.2)
Remark : the key is invalid for the “Indication of order of phases” function.
Successive
presses on … serve
short 1. to store the results of the present

measurements
2. to hold the display of the last value displayed
3. to return to normal display mode (the value of
each new measurement is displayed)
Long (>2 sec) ADC to perform automatic compensation of the zero
AAC+DC (see § 3.9.2)
WDC Remark : this mode operates if the MAX/MIN/PEAK or

HOLD modes (short press) are first desactivated
WAC+DC
Sustained to perform automatic compensation of the
resistance of the leads (see 3.6.1)
See also § 2.4.2 and § 2.5.1 for the action key with the action of the key
and with the action of the key.
2.2 KEY (SECOND FUNCTION)

This key is used to select the type of measurement (AC, DC, AC+DC) and the
second functions marked in yellow next to the relevant positions of the switch.
It can also be used, in the configuration mode, to modify the default value (see §3.4)
Remark: the key is invalid in the MAX/MIN/PEAK, HOLD and ΔREL modes.
Successive
… serve
presses on
short -to select AC, DC or AC+DC. Depending on your choice, the
screen displays AC, DC or AC+DC
14
-to cycle through the Ω and diode test modes and to return
to the continuity test
- to reset the measurement process for the “indicator of order
of rotation of the phases” function.
Long (>2 sec) - to display the total three-phase power of a balanced system
( is displayed).
- by pressing again, to return to display of the single-phase
power ( is off)
2.3 KEY
This key is used to backlight the display unit.
Successive
… serve
presses on
-to activate or de-activate the backlighting of the

screen
Remark: the backlighting is switched off automatically at the end of 2 minutes.
2.4 KEY
2.4.1 In the normal mode
This key activates detection of the MAX, MIN, PEAK+ and PEAK- values of the
measurements made.
Max and Min are the extreme mean values in DC and the extreme RMS values in AC.
Peak+ is the maximum instantaneous peak and Peak- the minimum instantaneous
peak.
R emark : in this mode, the "automatic switching off" function of the device is
automatically de-activated. The symbol is displayed on the screen.
15
Successive presses
… serve
on
-to activate detection of the MAX/MIN/PEAK values
-to display the MAX, MIN, PEAK+ or PEAK- value successively
-to return to display of the present measurement without exiting
from the mode (the values already detected are not erased)
R emark: the MAX, MIN, PEAK+, PEAK- symbols are both displayed, but
only the symbol of the quantity selected blinks.
short
Example: If MIN has been selected, MIN blinks and MAX, PEAK+, PEAK-
are lit steadily.
-to activate detection of the MAX/MIN values
-to display the MAX or MIN value successively
-to return to display of the present measurement without exiting
from the mode (the values already detected are not erased)
to exit from the MAX/MIN/PEAK mode. The values previously

recorded are then erased.
long (> 2 sec)
R emark: if the HOLD function is activated, it is not possible to exit from
the MAX/MIN/PEAK mode. The HOLD function must first be de-activated.
Remark : ΔREL function can be used with the functions of the MAX/MIN/PEAK
mode.
2.4.2 The MAX/MIN/PEAK mode + activation of the HOLD mode

Successive presses
… serve
on
to display successively the MAX/MIN/PEAK values

short
detected before the key was pressed.
Note : the HOLD function does not interrupt the acquisition of new MAX, MIN,
PEAK values.
16
2.4.3 Access to the True-INRUSH mode ( set to )
This key allows measurement of the True-Inrush current (starting current, or

overcurrent in steady-state operation) for AC or DC current only (not operational in
AC+DC).
Successive
…serves
presses on
long (>2 sec) to enter the True-INRUSH mode
-"Inrh" is displayed for 3s (the backlighting blinks)
-the triggering threshold is displayed for 5s (the
backlighting is steady);
-"------" is displayed and the "A" symbol flashes
-after detection and acquisition, the inrush
current measurement is displayed, after the
calculations stage "------" (backlighting off)
Remark: the A symbol flashes to indicate "surveillance"

of the signal.
to exit from the True-INRUSH mode (return to

simple current measurement).
short (<2 sec) -to display the PEAK+ value of the current
-to display the PEAK- value of the current
Note: a short press is -to display the RMS true-Inrush current
functional only if an
True-Inrush value has Remark: the A symbol is displayed steadily during this
been detected. sequence.
2.5 KEY
This key is used to display the frequency measurements of a signal, of the power,
and of the level of harmonics.
Remark : this button is not functional in DC.
2.5.1 The Hz function in the normal model
Successive
…serves
presses on
17
short to display:
-the frequency of the signal measured
-the present voltage (V) or current (A)
measurement
to display:
-the apparent power (VA)
- the reactive power (var)
- the power factor (PF)
- the frequency of the signal
- the active power (W)
long - to enter or exit from the level of harmonics
(THD) calculation and display mode
then short - to select THDf, THDr or the frequency of the
fundamental
2.5.2 The Hz function + activation of the HOLD mode
Successive
…serves
presses on
short -to store the frequency
-to display successively the stored frequency,
then the voltage or the current
- to display in turn the stored values of THDf,
then of THDr, then of the frequency of the
fundamental
2.6 KEY
This key is used to display and store the reference value or to display the diferential
and relative value, in the unit of magnitude measured or in %.
Remark : in phasis rotation mode, the key is not operating.
18
Successive
…serve
presses on
- to enter the ΔREL mode, to store then display the reference
value. The ΔRef symbol is displayed.
short - to display the diferential value:
- (current value – reference (∆))
The ΔREL symbol is displayed.
- to display the relative value in %
current value – reference (∆)
reference (∆)
The ΔREL and % symbols are displayed.
- to display the reference. The ΔRef symbol is displayed
- to display the current value. The ΔRef symbol blinks.
long (>2 sec) to exit from the ΔREL mode
Remark : the “Relative mode ΔREL” function can be used with the functions of the
MAX/MIN/PEAK mode.
3 USE
3.1 COMMISSIONING
Insert the battery supplied with the device as follows:
1. Using a screwdriver, unscrew the screw of the battery compartment cover
(item 1) on the back of the housing and open it.
2. Place the battery in the compartment (item 2), taking care to get the
polarities right.
3. Close the battery compartment cover and screw it to the housing.
19
Figure 6 : the battery compartment cover
3.2 STARTING UP THE CLAMP MULTIMETER

The switch is set to OFF. Turn the switch to the function of your choice. The whole
display lights (all symbols) for a few seconds (see §1.3), then the screen of the
function chosen is displayed. The clamp multimeter is then ready to make
measurements.
3.3 SWITCHING THE CLAMP MULTIMETER

The clamp multimeter can be switched off either manually, by setting the switch to
OFF, or automatically, after ten minutes with no action on the switch and/or the
keys. Thirty (30) seconds before the device is switched off, an audible signal
sounds intermittently. To re-activate the device, press any key or turn the switch.
3.4 CONFIGURATION
As a safety measure, and to avoid repeated overloads on the inputs of the device,
we recommend performing configuration operations only when the device is
disconnected from all dangerous voltages.
20
3.4.1 Programming of the maximum resistance allowed for a

continuity
To program the maximum resistance allowed for a continuity
1. From the OFF position, hold the key down while turning the switch to
, until the "full screen" display ends and a beep is emitted, to enter the
configuration mode. The display unit indicates the value below which the
buzzer is activated and the symbol is displayed.
The value stored by default is 40Ω. The possible values lie between 1Ω
and 599Ω.
2. To change the threshold, press the key. The right-hand digit flashes:
each press on the key increments it. To shift to the next digit, apply a
long press (>2s) to the key.
To exit from the programming mode, turn the switch to another setting. The
detection threshold chosen is stored (emission of a double beep).
3.4.2 De-activation of automatic switching off (Auto Power OFF)

To de-activate automatic switching off:
In the OFF position, hold the key down while turning the switch to
configuration mode. The symbol is displayed.
When the key is released, the device is in the voltmeter function in
the normal mode.
The return to Auto Power OFF takes place when the clamp is switched
back on.
3.4.3 Programming of the current threshold for the True INRUSH

measurement
To program the triggering current threshold of the True INRUSH measurement:
1. in the OFF position, hold the key down while turning the switch to
configuration mode. The display unit indicates the percentage overshoot to
apply to the measured current to determine the measurement triggering
threshold.
The value stored by default is 10%, representing 110% of the established
current measured. The possible values are 5%, 10%, 20%, 50%, 70%,
100%, 150%, and 200%.
21
2. To change the threshold, press the key. The value flashes: each
press on the key displays the next value. To record the chosen
threshold, apply a long press (>2s) on the key. A confirmation beep is
emitted.
To exit from the programming mode, turn the switch to another setting. The chosen
threshold is stored (emission of a double beep).
Note: The starting current measurement triggering threshold is fixed at 1% of the
least sensitive range. This threshold is not adjustable.
3.4.4 Default configuration

To reset the clamp to its default parameters (factory configuration):
In the OFF position, hold the key down while turning the switch to
configuration mode. The "rSt" symbol is displayed.
After 2 s, the clamp emits a double beep, then all of the symbols of the
screen are displayed until the key is released. The default parameters
are then restored:
Continuity detection threshold =40Ω
True Inrush triggering threshold =10%
3.5 VOLTAGE MEASUREMENT (V)

To measure a voltage, proceed as follows :
1. Set the switch to ;
2. Connect the black lead to the COM terminal and the red lead to "+".
3. Place the test probes or the crocodile clips on the terminals of the circuit
to be measured. The device selects AC or DC automatically according to
which measured value is larger. The AC or DC symbol lights in blinking
mode.
To select AC, DC or AC+DC manually, press the yellow key to reach the desired
choice. The symbol corresponding to the choice made then lights in fixed mode.
22
The measured value is displayed on the screen.
3.6 CONTINUITY TEST

Warning : Before performing the test, make sure that the circuit is off and any
capacitors have been discharged.
1. Set the switch to ; the symbol is displayed ;
2. Connect the black lead to the COM terminal and the red lead to «+».
3. Place the test probes or the crocodile clips on the terminals of the
circuit or component to be tested.
An audible signal is emitted if there is continuity, and the measured value is

displayed on the screen.
23
3.6.1 Automatic compensation of the resistance of the leads
Warning : before the compensation is executed, the MAX/MIN and HOLD modes
must be de-activated.
To perform automatic compensation of the resistance of the leads, proceed as
follows:
1. Short-circuit the leads connected to the device.
2. Hold the key down until the display unit indicates the lowest
value. The device measures the resistance of the leads.
3. Release the key. The correction and the symbole are
displayed. The value displayed is stored.
Remark : the correction value is stored only if it is
≤ 2 Ω. Above 2 Ω, the value displayed blinks and is not stored.
3.7 RESISTANCE MEASUREMENT Ω

Warning : Before making a resistance measurement, make sure that the circuit is
cold and any capacitors have been discharged.
1. Set the switch to and press the key. The Ω symbol is

displayed;
2. Connect the black lead to the COM terminal and the red lead to « + »;
circuit or component to be measured ;
The measured value is displayed on the screen
Remark : to measure low resistance values, first carry out the compensation of the
resistance of the leads (see § 3.6.1).
24
3.8 DIODE TEST

Warning: Before performing the diode test, make sure that the circuit is cold and
any capacitors have been discharged.
1. Set the switch to and press the key twice. The symbol is
displayed.
2. Connect the black lead to the COM terminal and the red lead to «+».
component to be tested.
3.9 CURRENT MEASUREMENT (A)

The jaws are opened by pressing the trigger on the body of the device. The arrow
on the jaws of the clamp (see the diagram below) must point in the presumed
direction of flow of the current, from the generator to the load. Make sure that the
jaws have closed correctly.
Remark: the measurement results are optimal when the conductor is centred in the
jaws (aligned with the centring marks).
The device automatically selects AC or DC according to which measured value is
larger. The AC or DC symbol blinks.
3.9.1 AC measurement
For an AC current measurement, proceed as follows:
1. Set the switch to and select AC by pressing the key. The AC
symbol is displayed.
2. Encircle only the conductor concerned with the clamp ;
25
3.9.2 DC or AC+DC measurement

To measure the DC or AC+DC current, if the display unit does not indicate "0", first
correct the DC zero as follows:
Step 1 : to correct the DC zero

Important : The clamp must not be closed on the conductor during the DC zero
correction. Hold the clamp in the same position during the whole procedure so that
the correction value will be exact.
Press the key until the device emits a double beep and displays a value near
"0". The correction value is stored until the clamp is powered down.
Remark : the correction is effected only if the value displayed is < ± 6 A, otherwise
the value displayed blinks and is not stored. The clamp must be recalibrated (see
§5.3)
Step 2 : to make a measurement
1. The switch is set to . Select DC or AC+DC by pressing the yellow

key until the desired choice is reached.
2. Apply the clamp to only the conductor concerned.
26
The measurement is displayed on screen.
3.10 STARTING CURRENT OR OVERCURRENT (TRUE INRUSH)

MEASUREMENT
Remark : the measurement can be made only in AC or DC mode (AC+DC mode
disabled)
To measure a starting current or overcurrent, proceed as follows:
1. Set the switch to , correct the DC zero (§ 3.9.2), then apply the
clamp around the single conductor concerned.
2. Effect a long press on the key. The InRh symbol is displayed,
then the triggering threshold. The clamp then awaits detection of the
True-Inrush current.
"------" is displayed and the "A" symbol flashes.
3. After detection and acquisition for 100 ms, the RMS value of the True-
Inrush current is displayed, along with the PEAK+/PEAK- values
subsequently.
4. A long press on the key or a change of function leads to exiting
from the True-Inrush mode.
Remark : the triggering threshold in A is 6A if the initial current is zero (starting of
installation); it is that set in the configuration (see §3.4.3) for an established current
(overload in a installation).
3.11 POWER MEASUREMENTS W, VA, VAR AND PF

This measurement is possible en single-phase or in balanced three-phase.
Reminder : in DC or AC+DC power measurement, first correct the DC zero in
current (see § 3.9.2, step 1)
27
For the power factor (PF) and the powers VA and var, the measurement is possible
only in AC or AC+DC.
3.11.1 Measurement of single-phase power

1. Set the switch to and select VA, var, or PF by pressing the
key until the desired choice is reached;
2. The device automatically displays AC+DC. To select AC, DC, or
AC+DC, press the key until the desired choice is reached.
3. Connect the black lead to the COM terminal and the red lead to "+";
4. Place the test probes or the crocodile clips of the black lead on the
neutral (N), then those of the red lead on the L phase.
5. Clamp only the corresponding conductor, respecting the direction;
3.11.2 Balanced three-phase power measurement

1. Set the switch to and select VA, var, or PF by pressing the
key until the desired choice is reached
2. Press the yellow key until the symbol is displayed.
3. The device automatically displays AC+DC. To select AC, DC, or
AC+DC, press the yellow key until the desired choice is reached.
4. Connect the black lead to the COM terminal and the red lead to "+";
5. Connect the leads and the clamp to the circuit as follows:
…and the black lead is …then the clamp is on

If the red lead is connected…
connected the conductor
To the L1 phase to the L2 phase of the L3 phase
28
Reminder : the arrow on the jaws of the clamp (see the diagram below) must point
in the presumed direction of flow of the current from the source (producer) to the
load (consumer)
Remark : You can also measure the three-phase power on a balanced 4-wire
network by proceeding in the same way, or by proceeding as for the measurement
on a single-phase network, then multiplying the value found by three.
3.12 “DIRECTION OF ROTATION OF THE PHASES” OR “ORDER OF

THE PHASES” MODE
This mode is used to determine the order of the phases of a three-phase network
by the "2-wire" method.
To determine the order of the phases, proceed as follows:
Step 1: determination of a "reference" period:

1. Set the switch to . The rdy symbol is displayed; the device is
ready for the first phase order determination measurement;
2. Connect the black lead with crocodile clip to the COM terminal and
the red lead with test probe to "+";
3. Connect the crocodile clip to the presumed L1 phase and apply the
red test probe to the presumed L2 phase;
4. Press the yellow key. The ref symbol blinks on the screen. The
instrument is ready to determine the reference period. When the
reference period has been determined, an audible signal sounds and
the ref and symbols are displayed.
Remark : if the reference period has not been determined, the device emits a beep
and displays the "Err Hz" or "ErrV" message. The symbol flashes, then the "rdy"
message is displayed on the screen. Repeat the procedure from 4.
29
Step 2: determination of a "measurement" period:

Within the next 10 seconds, apply the test probe to the presumed L3
phase. The "MEAS" indication then blinks on the display unit as soon as
the L2 phase is disconnected; the device is in the calculation phase.
Remark: if the measurement period has not been determined, the device emits a
beep and displays the "Err Hz" or "ErrV" message, then "rdy". Repeat the
procedure from 4.
Result: when the order of the phases has been determined, the device emits a
beep and the indication of order of the phases is displayed on the screen, as
follows:
 0.1.2.3 when the direction of rotation is direct. The "0" symbol blinks and
turns clockwise;
 0.3.2.1 when the direction of rotation is reversed. The "0" symbol blinks
and turns anticlockwise.
Remark: if the order of the phases has not been determined, the device emits a
beep and displays the "Err" message. Repeat the procedure from 4.
3.13 FREQUENCY MEASUREMENT (HZ)

The frequency measurement is available in V, W and A for AC and AC+DC
quantities. The measurement is based on a count of the passages of the signal
through zero (positive-going edges).
3.13.1 Frequency measurement in voltage

To measure the frequency in voltage, proceed as follows:
1. Set the switch to and press the key. The Hz symbol is
displayed.
2. Select AC or AC+DC by pressing the yellow key until the desired
choice is reached.
3. Connect the black lead to the COM terminal and the red lead to “+”.
circuit to be measured.
30
3.13.2 Frequency measurement in current

1. Set the switch to and press the key. The Hz symbol is
displayed.
2. Select AC or AC+DC by pressing the yellow key until the desired
choice is reached.
3. Encircle only the conductor concerned with the clamp.
3.13.3 Measurement of frequency in power

In the single-phase AC or AC+DC Power (W) setting, it is possible to display the
frequency of the voltage of the signal on the terminals.
In the balanced three-phase AC or AC+DC Power (W) setting, it is possible to

display the frequency of the phase-to-phase voltage of the signal on the terminals.
31
3.14 MEASUREMENT OF THE LEVEL OF HARMONICS (THD) AND

OF THE FREQUENCY OF THE FUNDAMENTAL (NETWORK)
The device measures the total harmonic distortion with respect to the fundamental
(THDf) and the total harmonic distortion with respect to the true RMS value of the
signal (THDr) in voltage and in current. Similarly, it determines the frequency of the
fundamental by digital filtering and FFT, for network frequencies of 50, 60, 400, and
800Hz..
3.14.1 Measurement of the THD and of the frequency of the

fundamental in voltage
1. Set the switch to and press and hold (>2s) the key. The
THDf symbol is displayed. To select THDr, press the key again.
The THDr symbol is displayed. To select the frequency of the
fundamental, press the key again. The Hz symbol is displayed.
2. Connect the black lead to the COM terminal and the red lead to «+»;
circuit to be measured;
3.14.2 Measurement of the THD and of the frequency of the

fundamental in current
1. Set the switch to and press and hold (>2s) the key. The
THDf symbol is displayed. To select THDr , press again. The
THDr symbol is displayed. To select the frequency of the fundamental,
press the key again The Hz symbol is displayed.
2. Apply the clamp to only the conductor concerned.
32
33
4 CHARACTERISTICS
4.1 REFERENCE CONDITIONS
Quantities of influence Reference conditions

Temperature: 23°C ±2°C
Relative humidity: 45% to 75%
Supply voltage: 9.0V ±0.5V
Frequency range of the applied signal: 45–65Hz
Sine wave: pure
Peak factor of the applied alternating signal: √2
Position of the conductor in the clamp: centred
Adjacent conductors: none
Alternating magnetic field: none
Electric field: none
4.2 CHARACTERISTICS UNDER THE REFERENCE CONDITIONS

The uncertainties are expressed in ± (x% of the reading (R) + y points (pt)).
4.2.1 DC voltage measurement

0.00 V to 60.0 V to 600 V to 1000 V
Measurement range
59.99 V 599.9 V (1)
Specified
0 to 100% of the measurement range
measurement range
from 0.00V to 5.99V
±(1% R + 10 pt)
Uncertainties ±(1% R +3 pt)
from 6.00V to 59.99V
±(1% R +3 pt)
Resolution 0.01V 0.1V 1V
Input impedance 10MΩ
Note (1) - The display indicates "+OL" above +2000V and "-OL" below – 2000V in
REL mode
34
- Above 1000V, a repetitive beep indicates that the voltage being

measured is greater than the safety voltage for which the device is
guaranteed. The display indicates "OL"
4.2.2 AC voltage measurement
Measurement 0.15 V to 60.0 V to 600 V to 1000V RMS

range 59.99 V 599.9 V 1400V peak (1)
Specified
measurement 0 to 100% of the measurement range
range (2)
from 0.15V to 5.99V
± (1% R + 10 pt)
Uncertainties from 6.00V to ± (1% R +3 pt)
59.99V
± (1% R +3 pt)
Note (1) - The display indicates "OL" above 1000V (1400V in PEAK mode).
- Above 1000V, a repetitive beep indicates that the voltage being
measured is greater than the safety voltage for which the device is
guaranteed. The display indicates "OL".
- Bandwidth in AC = 3 kHz
Note (2) Any value between zero and the min. threshold of the measurement range
(0.15V) is forced to "----" on the display.
35
4.2.3 AC+DC voltage measurement
60.0 V to 600 V to 1000V

0.15 V to
Measurement range (2) 599.9 V RMS (1)
59.99 V
1400V peak
Specified measurement
range
Uncertainties from 0.15V to 5.99V
± (1% R+10 pt)
± (1% R +3 pt)
from 6V to 59.99V
± (1% R +3 pt)
Note (1) - The display indicates "OL" above 1000V (1400V in PEAK mode).
- Above 1000V (DC or RMS), a repetitive beep indicates that the voltage
being measured is greater than the safety voltage for which the device is
guaranteed.
Note (2) - Any value between zero and the min. threshold of the measurement
range (0.15V) is forced to "----" on the display.
Specific characteristics in MAX/MIN mode in voltage (from 10Hz to 1kHz in AC

and AC+DC, and from 0.30V):
• Uncertainties: add 1% R to the values in the tables above.
• Capture time of the extrema: approximately 100ms.
Specific characteristics in PEAK mode in voltage (from 10Hz to 400 Hz in AC

and AC+DC):
• Uncertainties: add 1.5% R to the values in the tables above.
• PEAK capture time: 1ms min. to 1.5ms max.
4.2.4 DC current measurement
Measurement 0.00 A to 60.0 A to

600 A to 900 A (1)
range (2) 59.99 A 599.9 A
Specified
range
Uncertainties (2) ± (1% R+10
± (1% R +3 pt)
(zero corrected) pt)
Resolution 0.01A 0.1A 1A
36
Note (1) -The display indicates “+OL" above 1800A and "-OL" below –1800A in
REL mode. The “-“ and “+” signs are managed (polarity).
Note (2) - The residual current at zero depends on the remanence; It can be
corrected by the “DC zero” function of the HOLD key.
4.2.5 AC current measurement
Measurement range 0.15 A to 60.0 A to

600 A (1)
(2) 59.99 A 599.9 A
Specified
measurement range
Uncertainties ± (1% R + 10 pt) ± (1% R +3 pt)
Note (1) - The display indicates "OL" above 900A in PEAK mode. The "-" and "+"
signs are not managed.
Note (2) - Any value between zero and the min. threshold of the measurement
range (0.15V) is forced to “----“ on the display.
- Residual current at zero <150mA.
4.2.6 AC+DC intensity measurement

AC: 600 A
Measurement range 0.15 A to 60.0 A to
DC or PEAK: 600 A to
(2) 59.99 A 599.9 A
900 A (1)
Specified
measurement range
Uncertainties (2) ± (1% R+10
± (1% R +3 pt)
(zero corrected) pt)
Note (1) - In DC, the display indicates "+OL" above +1800A and "+-OL" above -
1800A in REL mode. The "-" and "+" signs are managed (polarity).
- In AC and AC+DC, the display indicates "+OL" above 900A in
PEAK mode. The "-" and "+" signs are not managed.
Note (2) - In AC, any value between zero and the min. threshold of the
measurement range (0.15A) is forced to "----" on the display.
- Residual current at zero:
37
• In DC: depends on the remanence. Can be corrected by the "DC

zero" function of the HOLD key
• In AC: <150mA
Specific characteristics in MAX/MIN mode in current (from 10Hz to 1kHz in AC

and AC+DC, and from 0.30 A):
• Uncertainties: add ± (1% R) to the values in the tables
above.
Specific characteristics in PEAK mode in current (from 10Hz to 400 Hz in AC

and AC+DC):
• Uncertainties: add ± (1.5% R+0.5A) to the values in the tables above.
4.2.7 True-Inrush measurement
Measurement range 6 A to 600 A AC 6 A to 900 A DC

Specified measurement range 0 to 100% of the measurement range
Uncertainties ± (5% R + 5 pt)
Resolution 1A
Specific characteristics in PEAK mode in True-Inrush (from 10Hz to 400 Hz in

AC):
• Uncertainties: add ± (1.5% R+0.5A) to the values in the tables above.
4.2.8 Continuity measurement
Measurement range 0.0Ω to 599.9 Ω

Open-circuit voltage ≤ 3,6 V
Measurement current 550 µA
Uncertainties ± (1% R +5 pt)
Buzzer triggering threshold Adjustable from 1Ω to 599Ω (40Ω is the default)
4.2.9 Resistance measurement
0.0 Ω to 600 Ω to 6.00 kΩ to

Measurement range (1)
599.9 Ω 5999 Ω 59.99 kΩ
1 to 100% of the
Specified measurement 0 to 100% of the measurement
measurement
range range
range
Uncertainties ± (1% R +5 pt)
38
Resolution 0.1Ω 1Ω 10Ω

Open-circuit voltage ≤ 3,6 V
Measurement current 550µA 100µA 10µA
Note (1) - Above the maximum display value, the display unit indicates "OL".
- The "-" and "+" signs are not managed.
Specific characteristics in MAX/MIN mode:

• Uncertainties: add 1% R to the values of the table above.
4.2.10 Diode test
Measurement range 0.000V to 3.199V DC

Uncertainties ± (1% R + 3 pt)
Resolution 0.001V
Measurement current 0.55 mA
Indication: junction reversed or Display of "OL" when the measured
open-circuit voltage >3.199V
 Note : The "-" sign is disabled for the diode test function.
4.2.11 Active DC power measurements

6.00 kW
Measurement 0 W to 60.0 kW to 600 kW to
to
range (2) 5999 W 599.9 kW 900 kW (1)
59.99 kW
Specified
1 to 100% of the
measurement range
range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3)
Resolution 1W 10W 100W 1,000W
Note (1) - Display of O.L or ± O.L

- Above 900kW in single-phase (1000V x 900A).
- Above ±1800kW, in REL mode.
39
Note (2) - Any applied voltage greater than 1000V causes the emission of an
intermittent alarm beep to report a dangerous overload.
Note (3) - The measurement result may be perturbed by an instability linked to the
current measurement (approximately 0.1A).
Example: for a power measurement made at 10A, the instability of the
measurement will be 0.1A/10A or 1%.
4.2.12 Active AC power measurements
6.00 kW
Measurement 5 W to 60.0 kW to
to 600 kW (1)
range (2) (4) 5999 W 599.9 kW
59.99 kW
Specified 1 to 100% of the
measurement measurement 0 to 100% of the measurement range
range range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3) (7)
Resolution 1W 10W 100W 1000W
Note (1) - Display of O.L

- Bandwidth in AC in voltage = 3 kHz, in current = 3 kHz
Notes (2) and (3) of the previous § apply.
Note (4) - Any power measured less than 5W is regarded as zero and causes the
display of dashes "----"
- If the voltage is less than 0.15V or if the current is less than 0.15A, the
power measured is regarded as zero and causes the display of dashes "----"
Note 5 - The active powers are positive for power consumed and negative for
power generated.
Note 6 - The signs of the active and reactive powers and power factor are defined
by the four-quadrant rule below:
- The diagram below sums up the signs of the power as a function of the
phase angle between U and I:
Quadrant 1 : Active power P sign + (power consumed)
Quadrant 2 : Active power P sign - (power generated)
Quadrant 3 : Active power P sign - (power generated)
Quadrant 4 : Active power P sign + (power consumed)
40
Note (7) - In balanced three-phases, with deformed signals (THD and harmonics),
uncertainties are guaranted since Ф > 30°. Additionals errors are following ,
depending of THD :
Add +1% for 10% < THD < 20%
Add +3% for 20% < THD < 30%
Add +5% for 30% < THD < 40%
4.2.13 Active AC+DC power measurements
6.00 kW
Measurement 5 W to 60.0 kW to 600 kW to
to
range (2) (4) 5999 W 599.9 kW 900 kW (1)
59.99 kW
Specified
1 to 100% of the
measurement range
range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3) (7)
Resolution 1W 10W 100W 1000W

Notes (2), (3), (4), 5, 6 and (7) of the previous § apply.
41
4.2.14 Measurement of apparent AC power
Measurement 5 VA to 6.00 kVA to 60.0 kVA to

600 kVA (1)
range (2) (4) 5999 VA 59.99 kVA 599.9 kVA
Specified 1 to 100% of the
measurement measurement 0 to 100% of the measurement range
range range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3)
Resolution 1VA 10VA 100VA 1000VA

- Above 600 kVA in single-phase (1000 V x 600 A).
Notes (2), (3) and (4) of the previous § apply.
4.2.15 Measurement of apparent AC+DC power
Measurement 5 VA to 6.00 kVA to 60.0 kVA to 600 kVA to

range (2) (4) 5999 VA 59.99 kVA 599.9 kVA 900 kVA (1)
Specified
1 to 100% of the
measurement range
range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3)
Resolution 1VA 10VA 100VA 1000VA

- Above 900 kVA in single-phase (1000 V x 900 A).
42
4.2.16 Measurement of reactive AC power
6.00 kvar
Measurement 5 var to 60.0 kvar to
to 600 kvar (1)
range (2) (4) 5999 var 599.9 kvar
59,99 kvar
Specified
1 to 100% of the
measurement range
range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3) (8)
Resolution 1 var 10 var 100 var 1000 var

- Above 600 kvar in single-phase (1000 V x 600 A).
Note 5 - In single-phase, the sign of the reactive power is determined by the
phase lead or lag between the U and I signs, while in balanced three-
phase, it is determined by the calculation on the samples.
Note 6 - Signs of reactive powers according to the four-quadrant rule (§4.2.12):
Quadrant 1 : Reactive power Q sign +
Quadrant 2 : Reactive power Q sign +
Quadrant 3 : Reactive power Q sign -
Quadrant 4 : Reactive power Q sign –
Note (8) - In single phase, with deformed signals (THD and harmonics),
uncertainties are guaranted since Ф > 30°. Additionals errors are following ,
depending of THD :
Add +1% for 10% < THD < 20%
Add +3% for 20% < THD < 30%
Add +5% for 30% < THD < 40%
4.2.17 Measurement of reactive AC+DC power
6.00 kvar 60.0 kvar
Measurement 5 var to 600 kvar to
to to
range (2) (4) 5999 var 900 kvar (1)
59.99 kvar 599.9 kvar
Specified
1 to 100% of the
measurement range
range
Uncertainties
± (2% R +10 pt) ± (2% R +3 pt)
(3) (8)
Resolution 1 var 10 var 100 var 1000 var
43

- Above 900 kvar in single-phase (1000 V x 900 A).
Notes (2), (3) , (4), 5, 6 and (8) of the previous § apply.
Specific characteristics in MAX/MIN mode in power (from 10Hz to 1kHz):
• Capture time: approximately 100ms
4.2.18 Calculation of the power factor
Measurement range (1) -1.00 to +1.00

Specified measurement range 0 to 50% of the 50 to 100% of the
measurement range measurement range
Uncertainties (7) ± (3% R +3 pt) ± (2% R +3 pt)
Resolution 0.01
Note (1) - If one of the terms in the calculation of the power factor is displayed as
"OL", or forced to zero, the display of the power factor is an indeterminate
value "----".
Note (7) of the previous § apply.

Note 9 - Sign of the power factor according to the four-quadrant rule (§4.2.12):
Quadrant 1 : Power factor PF sign + (inductive system)
Cos Φ sign +
Quadrant 2 : Power factor PF sign - (capacitive system)
Cos Φ sign -
Quadrant 3 : Power factor PF sign + (inductive system)
Cos Φ sign -
Quadrant 4 : Power factor PF sign - (capacitive system)
Cos Φ sign +
Specific characteristics in MAX/MIN mode (from 10Hz to 1kHz):
• Capture time: approximately 100ms.
44
4.2.19 Frequency measurements

4.2.19.1 C harac teris tic s in voltage
5.0 Hz to 600 Hz to 6.00 kHz to
Measurement range (1)
599.9 Hz 5999 Hz 19.99 kHz
1 to 100% of the
Specified measurement 0 to 100% of the measurement
measurement
range range
range
Uncertainties ± (0.4% R + 1 pt)
Resolution 0.1Hz 1Hz 10Hz
4.2.19.2 C harac teris tic s in c urrent

Measurement range (1) 5.0 Hz to 2999 Hz
Uncertainties ± (0.4% R + 1 pt)
Resolution 0.1Hz
Note (1) in MAX/MIN mode, the operating range is limited to 1kHz.

- If the level of the signal is too low (<10% of the range, or U<10V or
I<10A) or if the frequency is less than 5Hz, the device cannot determine
the frequency and displays dashes "----".
Specific characteristics in MAX/MIN mode (from 10Hz to 1kHz):

• Uncertainties: add 1% R to the values of the table above.
4.2.20 Characteristics in THDr
Measurement range 0.0 – 100%

Uncertainties ± (5% R ±2 pts) in voltage
± (5% R ±5 pts) in current
Resolution 0.1%
4.2.21 Characteristics in THDf
Measurement range 0.0 – 1000%

Uncertainties ± (5% R ±2 pts) in voltage
± (5% R ±5 pts) in current
Resolution 0.1%
45
 Note : - The display is "----" if the input signal is too low (U<5V or I<6A) or if the
frequency is less than 5Hz.
Specific characteristics in MAX/MIN mode in THD (from 10Hz to 1kHz):

• Capture time of the extrema: approximately 100ms
4.2.22 Indication of order of the phases
Frequency range 47Hz to 400Hz

Acceptable voltage range 50V to 1,000V
Duration of acquisition of the reference period ≤500ms
Duration of validity of the reference period approximately 10s at 50Hz
information approximately 2s to 400Hz
Duration of acquisition of the measurement period
≤500ms
+ display of the order of the phases
Acceptable phase unbalance ±10
Acceptable amplitude unbalance 20%
Acceptable level of harmonics in voltage 10%
4.3 ENVIRONMENTAL CONDITIONS
Environmental conditions in use in storage

Temperature -20 C to + 55 C -40 °C to + 70°C
Relative humidity (RH): ≤90% at 55°C ≤90% up to 70° C
46
4.4 CHARACTERISTICS OF CONSTRUCTION
Housing: Rigid polycarbonate shell with moulded elastomer covering

Polycarbonate
Jaws: Opening: 34 mm
Clamping diameter: 34 mm
LCD display unit
Screen: Blue backlighting
Dimension: 28 x 43.5 mm
Dimension: H-222 x W-78 x D-42 mm
Weight: 340g (with the battery)
4.5 POWER SUPPLY
Batter: 1 x 9 V LF22
Mean life: >120 hours (without backlighting)
Duration of operation before After 10 minutes without action on the switch
automatic switching off: and/or keys
4.6 COMPLIANCE WITH INTERNATIONAL STANDARDS
Compliant with standards IEC-61010-1, IEC-61010-2-

Electric safety: 30, and IEC-61010-2-32:
1000V CAT-III or 600V CAT IV.
Electromagnetic Compliant with standard EN-61326-1

compatibility: Classification: residential environment
Mechanical
Free fall: 2m (in accordance with standard IEC-68-2-32)
strength:
Level of protection
IP40 (per standard IEC-60529)
of the housing:
47
4.7 VARIATIONS IN THE DOMAIN OF USE

Quantity of Range of Quantity Influence
influence influence influenced Typical MAX
V AC - 0,1%R/10°C
V DC 0,1%R/10°C 0,5%R/10°C + 2pts
A 1%R/10°C 1,5%R/10°C + 2pts
Temperature -20...+55°C
Ω - 0,1%R/10°C + 2 pts
W AC - 0,2%R/10°C + 1°C
W DC 0,15%R/10°C 0,3%R/10°C + 2 pts
V ≤ 1 pt 0,1%R + 1 pt
A - 0,1%R + 2 pts
Humidity 10%...90%HR
Ω 0,2%R 0,3%R + 2 pts
W 0,25%R 0,5%R + 2 pts
10 Hz...1 kHz 1%R + 1 pt 1%R + 1 pt
V
1 kHz...3 kHz 8%R + 1 pt 9%R + 1 pt
Frequency
10 Hz…400 Hz 1%R + 1 pt 1%R + 1 pt
A
400 Hz…3 kHz 4%R + 1 pt 5%R + 1 pt
Position of the Any position on
conductor in the the internal
A-W 2%R 4%R + 1 pt
jaws perimeter of the
(f≤400 Hz) jaws
Adjacent Conductor
conductor touching the
carrying a external A-W 30 dB 20 dB
current of 150 A perimeter of the
DC or RMS jaws
Conductor
0-500 A DC or
enclosed by the V < 1 pt 1 pt
RMS
clamp
Application of a
0-1000 V DC or
voltage of the A-W < 1 pt 1 pt
RMS
clamp
1,4 to 3,5
limited A (AC-AC+DC) 1%R 3%R + 1 pt
Peak factor
to 900 A peak V (AC-AC+DC) 1%R 3%R + 1 pt
1400 V peak
48
5 MAINTENANCE
The instrument has no parts that can be replaced by personnel who are not trained
and approved. Any non-approved repair or other work, or replacement of a part by
an "equivalent", may severely compromise safety.
5.1 CLEANING
• Disconnect everything connected to the device and set the switch to OFF.
• Use a soft cloth moistened with soapy water. Rinse with a damp cloth and
dry quickly using a dry cloth or forced air.
• Dry perfectly before putting back into use.
5.2 REPLACEMENT OF THE BATTERY

The symbol indicates that the battery is spent. When this symbol appears on
the display unit, the battery must be replaced. The measurements and
specifications are no longer guaranteed.
To replace the battery, proceed as follows:
1. Disconnect the measurement leads from the input terminals.

2. Set the switch to OFF.
3. Use a screwdriver to unscrew the screw securing the battery compartment
cover to the back of the housing and open the cover (see §3.1).
4. Replace the battery (see §3.1).
5. Close the cover and screw it to the housing.
5.3 METROLOGICAL CHECK

Like all measuring or testing devices, the instrument must be checked regularly.
This instrument should be checked at least once a year. For checks and
calibrations, contact one of our accredited metrology laboratories (information and
contact details available on request), at our Chauvin Arnoux subsidiary or the
branch in your country.
5.4 REPAIR
For all repairs before or after expiry of warranty, please return the device to your
distributor.
49
6 WARRANTY
Except as otherwise stipulated, our warranty is valid for three years starting from
the date on which the equipment was sold. Extract from our General Conditions of
Sale provided on request.
The warranty does not apply in the following cases:
• Inappropriate use of the equipment or use with incompatible equipment;
• Modifications made to the equipment without the explicit permission of the
manufacturer’s technical staff;
• Work done on the device by a person not approved by the manufacturer;
• Adaptation to a particular application not anticipated in the definition of the
equipment or not indicated in the user’s manual;
• Damage caused by shocks, falls, or floods.
7 DELIVERY CONDITION
The F205 clamp multimeter is delivered in its packaging box with :
• 2 banana-banana leads, one red and one black

• 2 test probes, one red and one black
• 1 black crocodile clip
• 1 9V batteries
• 1 carrying bag
• the multiligual user manual on mini-CD
• the multiligual getting started guide
50
04 - 2013
Code : 692884A02 - Ed. 3
DEUTSCHLAND - Chauvin Arnoux GmbH SCHWEIZ - Chauvin Arnoux AG

Straßburger Str. 34 - 77694 Kehl / Rhein Moosacherstrasse 15 - 8804 AU / ZH
Tel: (07851) 99 26-0 - Fax: (07851) 99 26-60 Tel: +41 44 727 75 55 - Fax: +41 44 727 75 56
ESPAÑA - Chauvin Arnoux Ibérica SA UNITED KINGDOM - Chauvin Arnoux Ltd

C/ Roger de Flor N° 293, Planta 1- 08025 Barcelona Unit 1 Nelson Court – Flagship Square-Shaw Cross Business Park
Tel: 902 20 22 26 - Fax: 934 59 14 43 DEWSBURY – West Yorkshire – WF12 7TH
Tel : 019244 460 494 – Fax : 01924 455 328
ITALIA - Amra SpA MIDDLE EAST - Chauvin Arnoux Middle East

Via Sant’Ambrogio, 23/25 - 20050 Bareggia di Macherio (MI) P.O. BOX 60-154 - 1241 2020 JAL EL DIB (Beirut) – LEBANON
Tel: 039 245 75 45 - Fax: 039 481 561 Tel: (01) 89 04 25 - Fax: (01) 89 04 24
ÖSTERREICH - Chauvin Arnoux Ges.m.b.H CHINA - Shanghai Pu-Jiang - Enerdis Instruments Co. Ltd
Slamastrasse 29/2/4 - 1230 Wien 3 F, 3 rd Building - N° 381 Xiang De Road - 200081 SHANGHAI
Tel: 01 61 61 961-0 - Fax: 01 61 61 961-61 Tel: +86 21 65 21 51 96 - Fax: +86 21 65 21 61 07
SCANDINAVIA - CA Mätsystem AB USA - Chauvin Arnoux Inc - d.b.a AEMC Instruments

Box 4501 - SE 18304 TÄBY 200 Foxborough Blvd. - Foxborough - MA 02035
Tel: +46 8 50 52 68 00 - Fax: +46 8 50 52 68 10 Tel: (508) 698-2115 - Fax: (508) 698-2118
http://www.chauvin-arnoux.com
190, rue Championnet - 75876 PARIS Cedex 18 - FRANCE

Tél. : +33 1 44 85 44 85 - Fax : +33 1 46 27 73 89 - [email protected]
Export : Tél. : +33 1 44 85 44 86 - Fax : +33 1 46 27 95 59 - [email protected]

Clamp Multimeter: User's Manual

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Clamp Multimeter: User's Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Clamp Multimeter: User's Manual

Uploaded by

Copyright:

Available Formats

 CLAMP MULTIMETER

2.1 KEY ....................................................................................................................................13

3.11 POWER MEASUREMENTS W, VA, VAR AND PF .....................................................27

4.7 VARIATIONS IN THE DOMAIN OF USE ...................................................................48

7 DELIVERY CONDITION ........................................................................................ 50

For best results from your device :

Meanings of the s ymbols us ed on the devic e

Application or withdrawal authorized on uninsulated or bare conductors at

The CE marking indicates compliance with European directives.

Double insulation or reinforced insulation.

Selective sorting of wastes for the recycling of electrical and electronic

AC and DC – Alternating and direct current.

Risk of electric shock.

PRECAUTIONS FOR USE

Definitions of the measurement categories :

CAT II: Circuits directly connected to the low-voltage installation.

CAT III: Power supply circuits in the installation of the building.

CAT IV: Circuits supplying the low-voltage installation of the building.

Jaws with centring marks 3.5 to

4 5 Display unit 1.3

Figure 1 : the F205 clamp multimeter

1.1 THE SWITCH

Figure 2 : the switch

Item Function See §

1.2 THE KEYS OF THE KEYPAD

Figure 3 : the keys of the keypad

Item Function See §

1.3 THE DISPLAY UNIT

Figure 4 : the display unit

Item Function See §

1.3.1 The symbols of the display unit

AC Alternating current or voltage

DC Direct current or voltage

AC+DC Alternating and direct current or voltage

∆REL Relative value, with respect to a reference

∆Ref Reference value

Storage of the values and hold of the display

Max Maximum RMS value

Min Minimum RMS value

Peak+ Maximum peak value

Peak- Minimum peak value

Balanced total three-phase power measurement

var Reactive power

THDf Total harmonic distortion with respect to the fundamental

Total harmonic distortion with respect to the true RMS

Indicator of order to the phases

Compensation of the resistance of the leads

Permanent display (automatic switching off de-activated)

Spent battery indicator

1.3.2 Measurement capacity exceeded (O.L)

1.4 THE TERMINALS

 perform automatic compensation of the resistance of the leads (see also §

short 1. to store the results of the present

WDC Remark : this mode operates if the MAX/MIN/PEAK or

2.2 KEY (SECOND FUNCTION)

-to activate or de-activate the backlighting of the

Remark: the backlighting is switched off automatically at the end of 2 minutes.

2.4.1 In the normal mode