K01 Type - 40°C +85°C 15000H: Applications
K01 Type - 40°C +85°C 15000H: Applications
K01 Type - 40°C +85°C 15000H: Applications
APPLICATIONS
Designed for professional power electronics.
Switch mode power supplies, converters, filtering devices.
SCREW SCREW “+” SIGN “+” SIGN
Safety VentSafety Vent
ØD + 1 mm
ØD + 1 mm
P
S S L + 2 mm L + 2 mm
Ød1 Ød1
L1 + 2 mmL1 + 2 mm
Ød Ød
Safety Vent
STUD style
STUD style FLAT
M
side (*)
H H Thread form
M5/M6
Ød
Diagram of dimensions (unit=mm)
Insert and screw threads: Metric (mm), UNF (inches)
STUD INSERT
ØD d d1 P INSERT SCREW L1 -L[-1+3] S[-1+1]
M H STYLE CODE
35 11 7.9 12.7 M8 12 M5 5MA x 9.5 2.5 5 0
51 18.5 13 22.7 M12 16 M5 5MA x 9.5 2.5 5 H
63 18.5 13 28.6 M12 16 M5 5MA x 9.5 2.5 5 H
63 17.3 17.3 28.6 M12 16 UNF 1/4-28 Low Post 1/4-28 x 3 8“ 3 4 W
63 17.3 17.3 28.6 M12 16 UNF 1/4-28 High Post 1/4-28 x 1 2“ 6 7 R
63 7.9 7.9 28.6 M12 16 UNF 10-32 Low Post 10-32 x 1 4“ 2 2.5 Z
63 12 7.9 28.6 M12 16 UNF 10-32 High Post 10-32 x 3 8“ 6 7 U
76 18.5 13 31.8 M12 16 M5 5MA x 9.5 2.5 5 H
76 18.5 13 31.8 M12 16 M5 5MA x 9.5 2.5 7 L
76 23.2 17.7 31.8 M12 16 M6 6MA x 10 4.5 7 6
76 17.3 17.3 31.8 M12 16 UNF 1/4-28 Low Post 1/4-28 x 3 8“ 3 4 W
76 17.3 17.3 31.8 M12 16 UNF 1/4-28 High Post 1/4-28 x 1 2“ 6 7 R
76 7.9 7.9 31.8 M12 16 UNF 10-32 Low Post 10-32 x 1 4“ 2 2.5 Z
76 12 7.9 31.8 M12 16 UNF 10-32 High Post 10-32 x 3 8“ 6 7 U
90 23.2 17.7 31.8 M12 16 M6 6MA x 10 4.5 7 H
51 13 13 (10)* 22.7 M12 16 PARP M5 5MA x 9.5 6 7 K
63 15 15 (13)* 28.6 M12 16 PARP M5 5MA x 9.5 6 7 K
76 19 15 (13)* 31.8 M12 16 PARP M5 5MA x 9.5 6 7 K
76 19 15 (13)* 31.8 M12 16 PARP M6 6MA x 10 6 7 Q
90 19 15 (13)* 31.8 M12 16 PARP M6 6MA x 10 6 7 Q
Note: (*) quote on the PARP deck of the flat side (PARP = Protection Against Reverse Polarity).
23
SPECIFICATIONS
Capacitance Tolerance ±20% at 100 Hz, 20°C [M class IEC-62] on request: -10% +30% at 100 Hz, 20°C [Q class IEC-62]
Leakage Current (IL) max IL= 0.006 Cr Vr + 4 µA Kendeil product limit: IL= 0.003 Cr Vr
(mA, 5 min, 20°C) At 85°C max IL = 0.04 Cr Vr µA
Ripple current (Ir) Refer to table at 85°C and 100Hz. For different temperature and frequency multiplier must be used as follows:
Due to the current load capability of the contact elements, the following limits must not be exceeded:
CAPACITOR DIAMETER 35mm 51mm 63mm 76mm 90mm
Maximum current 20A 30A 40A 50A 70A
Insulation Resistance At 100V DC for 1 min is >100 MΩ across insulating sleeve and terminals.
Life test After 2,000 hours application of rated voltage at 85°C Cap change 10%
capacitors meet characteristics aside tan δ 130%
Leakage current (IL) < initial limit
Impedance (Z) 130%
Shelf life After leaving capacitors under no load for 500 hours at 85°C, Cap change ±15%
when restored at 20°C meet specifications aside tan δ 150%
Leakage current (IL) < initial limit
24
K01 TYPE STANDARD RATINGS
25
K01 TYPE STANDARD RATINGS
26
K01 TYPE STANDARD RATINGS
27
K01 TYPE STANDARD RATINGS
28
K01 TYPE STANDARD RATINGS
29
K01 TYPE STANDARD RATINGS
30
K01 TYPE STANDARD RATINGS
PLEASE TO CONTACT OUR TECHNICAL SERVICE FOR MORE INFORMATION OR SPEC-IN ANALYSIS.
31
USEFUL LIFE K01
3.0
2.5
2.0
Ir ac / Ir ac 85°C
1.5
1.0
0.5
480 ,000h
240,000h
120,000h
60,000h
30,000h
15,000h
35 40 45 50 55 60 65 70 75 80 85 90 95
Temperature °C
The graphs shows a typical trend of the standard capacitor load life.
For a more accurate calculation of the load life for a specific capacitor, please use our
calculator on the website www.kendeil.com or enquiry our technical service.
32
PART NUMBER SYSTEM
for screw type capacitors
New PART-NUMBER CODE in use since Sep 2010. Total length is 17 digits.
Please see examples below and have a reference code from the standard ratings capacitors pages.
DIGIT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
K Ø n n n
TYPE VOLTAGE CAPACITANCE TERM INSERT TOL RES CASE SIZE
EXAMPLES
K 0 1 1 0 0 2 2 3 0 H M 0 H 1 0 5 K01 100V 22000μF, Hi ripple, -20%+20%, 63x105