9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Maintenance Engineering and

Draft saved

2nd MCQ Questions

Q1. The 'bath-tub' curve indicates failure probability. Which stage is NOT 1 point
normally associated with the bathtub curve?

a) 'Infant-mortality' where failures occur early.

'b) Pulling the plug' where production is halted due to unacceptable level of failures.

'c) Normal-life' where few failures occur.

'd) Wear-out' where failure increases due to age.

Clear selection

Q2. Failure mode and effect analysis (FMEA) provide a checklist 1 point

procedure. Which of the following questions is NOT likely to feature on

a) What would be the cost of avoiding failure be?

b) What would the consequences of the failure be?

c) What is the likelihood that failure will occur?

d) How likely is such a failure to be detected before it affects the customer?

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 1/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q3. Which of the following is not counted among safety equipment? 1 point

a) Vacuum reliever

b) Alarms

c) Flashback arresters

d) Temperature reliever

Clear selection

Q4. The Japanese-inspired concept of fail-safeing (poka-yoke) seeks to 1 point

prevent human mistakes. Which of the following are not examples of

a) Digital counters on machines to ensure all parts are completed.

b) Sampling and checking work in a thorough manner.

c) Light beams that activate alarms if errors occur.

d) Gauges through which parts must pass on a machine.

Clear selection

Q5. The reliability of an operation is normally NOT improved by which one 1 point

of the following procedures?

a) Designing out fail points in the operation.

b) Ensuring some activities in the operation are 'fail-safe'.

c) Building redundancy into the operation.

d) Laying off employees who cause faults in the operation.

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 2/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q6. Total productive maintenance (TPM) has five goals. Which of the 1 point

following is NOT a goal of TPM?

a) Improve equipment effectiveness.

b) Train all staff in relevant maintenance.

c) Focus preventative maintenance where failure is most likely to occur.

d) Achieve autonomous maintenance.

Clear selection

Q7. Failure detection normally does NOT include which one of the 1 point

following techniques?

a) Questionnaires

b) Focus surveys

c) Lie detector tests

d) Complaint cards/feedback sheets

Clear selection

Q8. The benefits of maintenance do NOT include: 1 point

a) Higher end value

b) Enhanced safety

c) Increased operating costs

d) Increased reliability

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 3/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q9. Failure occurs due to defective parts during the: 1 point

a) Normal life stage

b) Wear out stage

c) Early-life stage

Clear selection

Q10. Frequency of inspection is decided on the basis of overloading. 1 point

a) True

b) False

Other:

Clear selection

Q11. Analysis of incidents that give customers either particular 1 point

satisfaction or dissatisfaction is:

a) Failure mode and effect analysis

b) Fault tree analysis

c) Product liability

d) Critical incident analysis

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 4/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q12. What are the activities of Program modularization and Source code 1 point

translation

A) Forward engineering

B) Reverse Engineering

C) Reengineering

D) Reverse Engineering and Reengineering

Other:

Clear selection

Q13. An approach that starts with a failure or potential failure and works 1 point
backward is:

a) Fault tree analysis

b) Accident investigation

c) Product liability

d) Failure mode and effect analysis

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 5/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q14. which category of software maintenance is used for the 1 point

modification of software that match changes in the ever-changing

A) Corrective

B) Adaptive

C) Perfective

D) Preventive

Other:

Clear selection

Q15. If a machine operator fails to clean or lubricate his or her machine in 1 point

the prescribed manner and it fails, this is an example of:

a) A misjudgement

b) A mistake

c) An error

d) A violation

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 6/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q16. Seismometer can be used to measure acceleration of any 1 point

instrument only if _____

a. it's natural frequency is high

b. it generates output signal which is proportional to relative acceleration of the

c. both a. and b.

d. none of the above

Other:

Clear selection

Q17. Temperature monitoring technique uses which of the following 1 point

devices to measure temperature of the machining surfaces?

a. Pyrometers

b. Thermocouples

c. Thermometers

d. All of the above

Other:

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 7/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q18. Which of the following statements is true about stroboscope? 1 point

a. Stroboscope is non-contact type frequency instrument

b. Stroboscope can measure frequency upto 5 Hz

c. Stroboscope uses electromagnetic radiations to measure frequency

d. All of the above

Other:

Clear selection

Q19. An approach that aims to identify the product or service feature 1 point

that is critical to various types of failure is:

a) Fault tree analysis

b) Product liability

c) Failure mode and effect analysis

d) Complaint analysis

Clear selection

Q20. Which type of frequency measuring instrument has multiple reeds 1 point

of different natural frequency to measure vibrations?

a. Fullarton tachometer

b. Frahm Tachometer

c. Both a. and b.

d. None of the above

Other:

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 8/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q21. Mean time between failures is calculated as the number of hours 1 point

that the product is working divided by the amount of downtime.

a) True

b) False

Clear selection

Q22. Which of the following instruments measure amplitude of a 1 point

vibrating body?

a. Vibrometers

b. Seismometer

c. Both a. and b.

d. None of the above

Other:

Clear selection

Q23. If a production line is unable to cope with the demands placed on it, 1 point

this is an example of a:

a) Facilities failure

b) Design failure

c) Supplier failure

d) Customer failure

Clear selection

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 9/10
9/25/21, 11:33 AM Maintenance Engineering and Management(PEC-ME-431 )2nd MCQ(25/09/21) Online Exam

Q24. Which of the following vibrometers have frequency ratio (ω/ωn) << 1 point

1?

a. Accelerometers

b. Velometers

c. Both a. and b.

d. None of the above

Other:

Clear selection

Q25. People failures come in two different types: 1 point

a) Violations and interdependence

b) Moderation and confusion

c) Errors and violations

d) Errors and ignorance

Clear selection

Back Submit Clear form

Never submit passwords through Google Forms.

This form was created inside of Aravali College of Engineering & Management. Report Abuse

 Forms

https://docs.google.com/forms/d/e/1FAIpQLScj2juHWi73R_RzjwRXVmdTJeG0cY94BMLuCvrU5lHM1v2SDQ/formResponse 10/10