MB ACC Self-Diagnostics

A/C DIAGNOSTICS
Since we are inside the car, I would like to address the great diagnostic capabilities
available with the modern pushbutton controller. Three different forms of diagnostic
information can be gathered here. I find the "actual value" function most helpful.
Diagnostic trouble codes are also available, along with the ability to activate the
individual door positions (individual flap tests) within the dash. All of these functions,
actual values, fault codes and mode activation, can be done from the various buttons on
the pushbutton assembly.
I really like the actual values, as one can drive the car and watch the activity of important
functions that include evaporator temperature, engine temperature, blower control
voltage, etc. See Chart 1 for the list of actual values for the 210 chassis E320. Other
chassis are similar, but this chart is given as an example.
The procedures for reading Actual Values go like this: Turn on the ignition, press the
"AUTO" button, set the temperature on each side to 72°F (this can be done quickly by
pressing both the red and blue arrows at the same time), then press the "REST" button for
five seconds or until the left-side display says "1."
The right-side display will then display the in-car temperature. Pressing the "AUTO" on
one side makes the positions change up or down (for example, 1, 2, 3, etc). Pressing the
opposite "AUTO" button runs the functions in the other direction (for example, 3, 2, 1).
The test can be ended at any time by tapping the "REST" button.
Figure 1 shows the Actual Value screen. It is value #5, which is evaporator temperature.
The right-side value of 06 is the temperature in Celsius.
I first ran across these tests while trying to solve a C230 problem whereby its compressor
would shut off within one minute of starting. There were some fault codes involved with
communication between the fan control module and the pushbutton module. I came
across the actual value test while trying to make some sense of the code. I tried the actual
values without the engine running. The evaporator temperature showed 155 degrees.
When I discovered that the dealer had two of the sensors in stock, I had a good idea that
the problem had been found.
The new sensor gave me realistic values and the problem was fixed. That model has a
variable displacement compressor and it was interesting to watch the evaporator
temperature while on a road test. It dropped rapidly, then slowed and finally just stopped
at 42 degrees. (It was probably 95 degrees outside at the time). This feature has many
values, as the list of data is comprehensive — engine temperature, engine speed, vehicle
speed, battery voltage — to name a few.
The procedures for pulling Fault Codes go like this (See Chart 3): Turn on the ignition,
and set the left temperature to "HI" and the right temperature to "LO." Then,
simultaneously press buttons "Rest" and "EC" for five or more seconds. All of this must
be done within 20 seconds. The "Recirculate" button will flash its LED. The screen will
then go blank, and the first code can be brought up by pressing the right "AUTO" button.
Subsequent codes are retrieved by additional application of the right "AUTO" button.
Figure 2 shows code B1234. Note that the code starts with "E" for error. Also note that
the B1234 code appears as Eb1 234 on the screen.
The Individual Flap Tests are run by idling the engine, pressing the left and right
"AUTO" buttons, setting temperatures to 72°, manually opening the fascia vents, and
simultaneously pressing the "Rest" and "Recirculate" buttons for more than five seconds.
The first step: Left display "0" and right display "LO" should appear. Pressing the left
"AUTO" button changes the steps. Pressing the right "AUTO" button varies the two
modes "HI" and "LO" for each step.
The functions that are checked are described in Chart 2 and can be verified by the actual air flow
changes enacted. Figure 3 shows the third step (DTC) with "2" indicated on the left side and the
"HI" mode indicated on the right.
All of these tests are so easy to run that they should be done frequently to gain familiarity with
them. They definitely should be run before and after major dash surgery.
A/C Service Diagnostic & Test Procedures:

Pre Evaporator Replacement Steps
1. Before you try to diagnose an A/C complaint on a Mercedes-Benz 140 model, a

complete cooling capacity test, function test and leak test are all musts.
a. A cooling capacity test is performed by evacuating the freon and measuring
the amount removed. This procedure will verify whether the system has lost
freon or is low in capacity.
b. A leak test is performed by adding 2.5 pounds of freon (2.9 with rear A/C)
and running the A/C on full cold at low fan speed. A leak detector can be
used in the vents or the drains under the vehicle located on each side of the
transmission.
c. A full function test should be performed by operating all of the normal
functions of the pushbutton, including auto, manual and REST. Activating
the pushbutton diagnostic mode and checking actual values, codes and
activation of flaps will also save time and embarrassing moments if an
evaporator replacement is justified. Oftentimes, a technician will not
perform these checks only to replace the evaporator. And when the task is
completed, he finds a leaking flap, or a defective sensor or pushbutton
assembly. Now, he must approach the customer for additional repairs that
could have been avoided if the above simple tests had been performed. Most
technicians are paid 1.5 hours for these tests that can accurately be
performed in 30 to 45 minutes.
2. Another option is to evacuate the system, install fluorescent dye, and then recharge
to test for leaks. Some evaporators with larger leaks may only need a few hours of
run time before the light can detect a leak, while others may take a few weeks of
driving. If dye is used, a simple way to see the dye is to remove the blower motor
and insert a smaller detector light in the evaporator housing through the blower area.
The front of the evaporator can easily be seen this way and the dye can be easily
detected. You can also insert a leak detector in the same area for verification.
3. In 1992, a longer evaporator was used. They were replaced on ‘94 models by newer,
updated evaporators that have a better cooling capacity and are about six inches
smaller. If an early-type evaporator is replaced with a newer, shorter-type
evaporator, it is a must that you use a baffle provided by the dealer to block off the
opened area that results from the use of the shorter evaporator. Failure to use a
baffle will cause a difference in air cooling of more than 15°F from the left to the
right side of the center A/C dash vent. The result of air bypassing the evaporator
fins, this temperature difference will also reduce total cooling capacity by roughly
30 percent.
4. Once the dash and supports are removed, the vehicle should never be raised. The
possibility of damaging the windshield, as a result of the chassis twisting while
raising the car without the braces, is great.
5. Base modules play a very important role in the function of the compressor
activation in the 140 model. One of the base module’s functions is to receive the
speed signal from the compressor and match it against a mapped grid that will
calculate the difference from engine speed. If the tolerance is exceeded, the base
module shuts off power to the compressor until the key is recycled. If the belt were
to slip due to water, the module would also shut off the compressor. When
activating the A/C pushbutton, the module will activate the compressor until it
receives its speed signal. If the signal is not received, the base module will quickly
shut off the compressor. This provides a quick self-test procedure seeing that if the
compressor comes on and then shuts off quickly when starting the system, one can
assume a speed signal problem exists.
6. The evaporator temperature sensor has the most control over compressor operation.
If the sensor resistance is shown as being below 2°C, the compressor is turned off.
The pushbutton module is also logically programmed to show an unrealistic value,
such as -40°C or +40°C if an open circuit in the sensor or a short to ground is
detected.
7. The sensors with the least control are the sun and smog sensors. The sun sensor
raises or lowers the speed of the blower by only a few percentages depending on the
direct sunlight, while the smog sensor opens or closes the fresh air flap again
depending on the carbon monoxide concentration in the air.
8. A very common problem in the 140 model equipped with a 119 V8 engine is that
the harness to the compressor connector A9x1 is too short, causing the wires to
break at the connector. Worn motor mounts and engine flex have been blamed for
the breakage. Mercedes-Benz increased the length of the harness in models with
production dates from 08/1994 to prevent this problem.

MB ACC Self-Diagnostics

Uploaded by

Copyright:

Available Formats

MB ACC Self-Diagnostics

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MB ACC Self-Diagnostics

Uploaded by

Copyright:

Available Formats

A/C DIAGNOSTICS

A/C Service Diagnostic & Test Procedures:

1. Before you try to diagnose an A/C complaint on a Mercedes-Benz 140 model, a

You might also like