TE-7R-MD, TE-7K-MD

TE-7S-MD

TE-7R-MD
TE-7K-MD

TE-7S-MD

PUMP CONSTRUCTION & SERVICING:

March “Orbital” Magnetic Drive Pumps eliminate the conventional shaft seals
found in most pumps. Hence, there is no rotating shaft or seal to wear and allow
the liquid being pumped to leak out. The only seal in the pump is a stationary “O”
ring seal between the front and the rear Housings. The only moving part other
than the motor is the Impeller Assembly, which rotates on a stationary shaft and
up against a thrust washer. These are the only parts that might wear and, may
require replacement.
MODEL ABBREVIATIONS:
TE = Totally Enclosed Fan Cooled Motor
TE-7R-MD

TE-7K-MD

TE-7S-MD
R = Polypropylene/Ryton
K = Kynar, S = Stainless Steel
MD = Magnetic Drive

OPERATION: SPECIFICATIONS
Pumps are not self priming, and will not Max Flow 50Hz lpm 180 180 180
produce a suction lift and must be installed 60Hz gpm 53 53 53
with a positive flooded suction. The liquid Max Head 50Hz m 12.3 12.3 12
60Hz ft (psi) 60 (26) 60 (26) 57.5 (25)
being pumped serves as the lubrication for the
Impeller Assembly spinning on the stationary Inlet 1-1/2” FPT 1-1/2” FPT 1-1/2” FPT
Outlet 1” MPT 1” MPT 1” MPT
shaft. If the pump is run dry for longer than 30
Max Internal psi 50 75 200
seconds, the Impeller may “freeze” onto the Pressure bar 3.4 5 13
shaft. A carbon bushing will enable dry running Max Liquid °F 190 200 250
protection. The direction of motor rotation Temperature °C 87 93 121
should be clockwise looking into the inlet of the Packed Weight kg/lbs 17.5/38.5 15/33 17.5/38.5 15/33 22.5/49.5 20/44
pump. A trimmed impeller may be necessary TEFC TEFC TEFC TEFC TEFC TEFC
when pumping a liquid with a specific gravity Motor Type
115/230 230/460 115/230 230/460 115/230 230/460
or viscosity greater than water as well in cases Phase 1 3 1 3 1 3
of high liquid temperature. Volts 115 230 230 460 115 230 230 460 110 220 190 380
Watts 764 764 628 628 764 764 628 628 740 740 730 730
ELECTRICAL: 50Hz Amps 10.4 5.2 2.2 1.1 10.4 5.2 2.2 1.1 12.4 6.2 2.6 1.3
The standard motor is 115/230 volts, 1 phase Kw .497 .497 .559 .559 .497 .497 .559 .559 .745 .745 .559 .559
or 230/460 volts, 3 phase rated as continuous Rpm 2850 2850 2850 2850 2850 2850 2850 2850 2850 2850 2850 2850
Volts 115 230 230 460 115 230 230 460 115 230 230 460
duty. The 7R & 7K have a 3/4 HP Motor. The
Watts 1231 1231 1023 1023 1231 1231 1023 1023 1140 1140 1118 1118
7S has a 1 HP Motor. A junction box is located
60Hz Amps 9.7 4.9 2.2 1.1 9.7 4.9 2.2 1.1 11.8 5.9 3.0 1.5
on the rear of the motor for making the electric Hp 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1 1 1 1
hook up. The wiring instructions are located on Rpm 3450 3450 3450 3450 3450 3450 3450 3450 3450 3450 3450 3450
the motor label or on the junction box cover. Electrical Connection Conduit Box Conduit Box Conduit Box Conduit Box Conduit Box Conduit Box
The motor has U.L. yellow card recognition. Overall Pump Height 8.94 7.38 8.94 7.38 8.94 7.38
Explosion proof and special voltage motors are Dimensions Width 8.96 8.96 8.96 8.96 8.96 8.96
available upon special order. (Inches) Length 17.81 17.31 17.81 17.31 18.29 17.29
Overall Pump Height 22.7 18.7 22.7 18.7 22.7 18.7
Dimensions Width 22.7 22.7 22.7 22.7 22.7 22.7
(cm) Length 45.2 43.9 45.2 43.9 46.4 43.9
TE-7S-MD PUMP ONLY:
The Impeller, shaft, and Thrust washer are packed separately within the carton to prevent damage during shipping. These items need to be assembled
into the pump before installation. Be sure all parts are assembled per the exploded view shown.

NOTE:
When replacing Impeller Bushing in the field: The plastic bushings
must be bored to size after they have been pressed into the
impeller. Bore to .378/.381 I.D. The carbon and ceramic bushings
are to finished size and do not require boring. When attaching drive
magnet (item 16) to the motor shaft, position the face of the drive
magnet 1/16 inch below the face of the motor bracket (item 17).

REPAIR PARTS LIST

TE-7R-MD

TE-7K-MD

TE-7S-MD
ITEM DESCRIPTION MATERIAL QTY PART #
1 Screw 1/4-20 x 2”Lg Stainless 6 0155-0014-1000 S S S
2 Washer 1/4 I.D. x 1/2 O.D. Stainless 6 0155-0021-1000 S S S
3 Front Housing Polypropylene 1 0155-0011-1000 S
4 Front Housing Kynar 1 0155-0125-1000 S
5 Front Housing 316 Stainless 1 0155-0036-0000 S
6A “O” Ring Viton 1 0155-0010-1000 S S S
6B “O” Ring Viton/Teflon 1 0155-0071-1000 O O O
7 Thrust Washer Ceramic 1 0155-0009-1000 S S S
8 Shaft – 4.070” Long Ceramic 1 0155-0039-1000 S S
9 Shaft – 4.257” Long Ceramic 1 0155-0117-1000 S
10A Impeller Assembly w/Teflon/Ryton/Carbon Bushing Polypropylene/Ryton 1 0155-0159-0500 S O
10B Impeller Assembly w/Carbon Bushing Polypropylene/Carbon 1 0155-0159-0200 O O
10C Impeller Assembly w/Mica Teflon Bushing Polypropylene/Teflon 1 0155-0159-0400 O O
11A Impeller Assembly w/Carbon Bushing Kynar/Carbon 1 0155-0160-0200 S O
11B Impeller Assembly w/Mica Teflon Bushing Kynar/Teflon 1 0155-0160-0400 O O
12A Impeller Assembly w/Carbon Bushing 316 Stainless/Carbon 1 0155-0112-0400 S
12B Impeller Assembly w/Mica Teflon Bushing 316 Stainless/Teflon 1 0155-0112-0800 O
12C Impeller Assembly w/Teflon/Ryton/Carbon Bushing 316 Stainless/Ryton 1 0155-0112-0300 O
13 Rear Housing w/Thrust Washer Ryton/Ceramic 1 0155-0067-0100 S
14 Rear Housing w/Thrust Washer Kynar/Ceramic 1 0155-0124-0100 S
15 Rear Housing 316 Stainless 1 0155-0035-0000 S
16 Drive Magnet Assembly 1 0155-0130-0200 S S S
17 Motor Connecting Bracket 1 0155-0092-0100 S S S
18 Screw 3/8-16 x 3/4”Lg Stainless 4 0155-0017-1000 S S S
19 Washer 3/8 I.D. x 5/8 O.D. Stainless 4 0155-0019-1000 S S S
18 Motor, TEFC, 3/4 H.P., 1 Phase, 115/230 Volt 1 0155-0016-1000 S S
19 Motor, TEFC, 3/4 H.P., 3 Phase, 230/460 Volt (Not Shown) 1 0155-0022-1000 S S
20 Motor, TEFC, 1 H.P., 1 Phase, 115/230 Volt (Not Shown) 1 0155-0173-1000 O O S
21 Motor, TEFC, 1 H.P., 3 Phase, 230/460 Volt (Not Shown) 1 0155-0174-1000 O O S
NOTE: Contact Factory for other materials and/or parts not listed. Legend: S = Standard, O = Optional
MATERIALS IN CONTACT WITH SOLUTION:
For TE-7R-MD: Polypropylene, Ryton, Viton, Ceramic, Ryton/Teflon/Carbon
For TE-7K-MD: Kynar/Carbon Filled, Viton, Ceramic, Carbon
For TE-7S-MD: 316 Stainless Steel, Viton, Ceramic, Carbon

NOTES:
All specifications & data are based on pumping water and are intended for use as a guideline only. Ratings & dimensions may vary depending on the
current motor being used.

LIMITED WARRANTY:
March pumps are guaranteed only against defects in workmanship or materials for a period of one year from date of manufacture pumping water. On
all other solutions, contact the factory for application assistance. March Pump Application Worksheet 0750-0130-1000 is available for additional
warranty information.
0155-0046-1000 R15 (Revised 9/22/09)