JOB SAFETY ANALYSIS (JSA)

TANK MODIFICATION AND REPAIR WORK

JSA Number: JSA Title: Coating and Raping activity

Task Description Coating and raping activity in side and out side tank
Uncontrolled Residual Risk
Risk
Step Activity Hazard H M L Control Measures H M L
1. Site preparation  Poor communication M  DESCON employees shall have mandatory training. L
between work parties.  Work permit from the client, with all concurring parties signatures
approval must be obtained prior to start of work and display at
site
 Safety requirements stated on the work permit must be available on
 Inexperience persons / lack site and strictly followed
of safety awareness  Toolbox talk shall be conducted to all personnel on site &
documented before start of work.
 Appropriate PPE shall be worn by all personnel at site.
 Assigned trained dedicated Banks man for job with reflective jacket.
 No water no work policy shall be followed.
 Heat stress  Work Schedule according to heat Index
 Ear protection shall be worn where required.
 Noise  Noise meter will be made available at site.
 Maintenance of equipment on regular basis.
 Vehicles Movement  Use of Approved/Trained license drivers.
 Vehicle movements on site shall be controlled by banks man
 Appropriate signage to be provided.
2. Confined space  Lake of Communication H  All personnel working in confined space must have L
entry. confined space training.
 PRL confined space procedure shall be followed.
 JOB SAFETY ANALYSIS (JSA)
TANK MODIFICATION AND REPAIR WORK

JSA Number: JSA Title: Coating and Raping activity

Task Description Coating and raping activity in side and out side tank
Uncontrolled Residual Risk
Risk
Step Activity Hazard H M L Control Measures H M L
 Hole watcher is attentive all the time during confined
 Ventilation. space activity. Lighting provided in CSE to be 24V.
 Easy communication between hole watcher and supervisor
 Damage material is established all the time.
 Ensure that passage and transport rout is clear during
 Oxygen deficiency confined space activities. Proper access/agrees should be
accumulation of toxic maintained.
gases  Gas test to be done by AGT prior to entering into
the confined space.
 A trained and qualified individual should outside the tank
with the responsibility of ensuring the safety of authorized
entrants (Fabricator, Fitter, Welder e.tc) through the
performance pre‐entry briefing, checking and inspecting
 Physical hazards PPE, equipment and tools and performing regular
monitoring in ensuring person working inside pipe remains
safe for entry and occupation.
 A written rescue plan that has provision for conducting a
timely rescue of individuals working inside the pipe
(Confined Space) should be kept on site. Raising the alarm
in the event of an emergency using the radio/mobile
 JOB SAFETY ANALYSIS (JSA)
TANK MODIFICATION AND REPAIR WORK

JSA Number: JSA Title: Coating and Raping activity

Task Description Coating and raping activity in side and out side tank
Uncontrolled Residual Risk
Risk
Step Activity Hazard H M L Control Measures H M L
phones provided to them.
 Ensure effective communication systems for the entry are
tested.
 Improper stacking of  Proper light should be provided less than 25v.
material  All material stack proper and category wise.
 Rescue arrangement shall be made while working more
than five meter inside large bore size.
 PRL SHE&S Procedure shall be followed.
 Unauthorized entrant  Close supervision required while working inside.
 Execute the work under close supervision and presence of
 Lack of oxygen hole watcher.
/oxygen/ air  Proper air supply to be provided or air mover will
deficiency be provided.
 Proper ventilation shall be there.
 Working crew shell be trained for confined space working.
11. Coating Works  Health hazards. M  Correct PPE should be worn L
 Respiration Hazards.  MSDS should be kept at site for PPE compliances
 Appropriate mask should be worn
JSA Number: JSA Title: Coating and Raping activity
Area: Activity: Coating and raping activity in side and out side tank Date

Task Description Coating and raping activity in side and out side tank
Uncontrolled Residual Risk
Risk
Step Activity Hazard H M L Control Measures H M L
 Manual Handling & storage  Hands should be cleaned with soap solution before eating
paint.  Storage of paint as per MSDS
 Waste Paint tins to be removed from the work site
and dispose to designated area (as per JGC
• Environmental pollution Procedure)
 Provide secondary containment 110% of largest cane.
 Keep proper type of fire extinguisher at site.
 Chemical Spillage  Keep minimum stock level at site.
 Spills to be reported immediately
 Portable Eye wash bottle shall be provided
• Inhalation of toxic fumes  Explain the expected hazards and remedies to the working
Or irritating eyes. crew’s chemicals that they are dealing with. Hazardous
material training to be done.
• Splatter from brush.  Care to be taken by all persons handling chemicals not
to spill, splash nor have contact with the substances.
• Slips, Trips, and Falls.  Safety harness/fall arrestor to be worn for work at height
Fire  100% tie off of safety harness all times
during erection/dismantling
JSA Number: JSA Title: Coating and Raping activity
Area: Activity: Coating and raping activity in side and out side tank Date

Task Description Coating and raping activity in side and out side tank
Uncontrolled Residual Risk
Risk
Step Activity Hazard H M L Control Measures H M L
 Supervisor to be on site at all times during work activity.
13 Extended  Inadequate lighting in and M  Adequate lighting at work area and Access/Egress area. L
hour/night Works around work areas, Emergency route to muster point to be clearly illuminated.
(Actual works will causing shadows or poorly  Proper cable management
be the same as lit work areas that could
 Use clear safety glass for night work for good visibility.
day work) result in unsafe acts and
injuries taking place  Warning Lights and sign boards.
 Trained Flag man for equipment movement provided with
signal torch.
 Close supervision required while working in night shift.
14 Emergency  Poor Communication M  Educate the workforce about Emergency Procedure. L
Procedure /  All safety sign board shall be displayed properly at site.
Response  In case of any Emergency all work will be stopped, Shut
down all running equipment & Machineries and reported to
Muster Point
 Improper Access/ Egress  Proper Access & Egress shall be available.
 All Workforces shall know the Muster Point location.
 PRL Emergency Procedure to be followed.
JSA Number: JSA Title: Coating and Raping activity
Area: Activity: Coating and raping activity in side and out side tank Date

Task Description Coating and raping activity in side and out side tank
Uncontrolled Residual Risk
Risk
Step Activity Hazard H M L Control Measures H M L
 Emergency # 00000000
 PRL Medical # 00000000
15. House keeping  Trips and fall M  All waste generated shall be contained and disposed off in L
designated waste skips.
 Sharp Objects  Do not store materials/equipments inside the plant area.
 Use Proper Personal protective equipment for handling of
 Equipment damage waste.
 All materials shall be removed from the site to a
safe storage location immediately after the work.

Approved
Signature Print Date

Performing Party
Signature Print Date