Scribd Logo
Upload

Welcome to Scribd!

  • 40 views

    Adjust Front Suspension Pos 2 DA 433

    Uploaded by

    kurniarung oceanda
    This JSEA document provides a 3-step job safety analysis for adjusting the front suspension on a DA 433 machine at the Wahana Coal Mine project workshop. The steps are: 1) preparation and isolation of the machine, 2) adjusting the suspension, and 3) finishing work. Hazards identified include slipping, falling, impacts, tool breakage, oil spills, and high-pressure nitrogen. Controls include following PPE standards, using danger tags, ensuring tools are used correctly, having spill containment, and using the service manual for suspension procedures. The JSEA was prepared and approved by safety and operations managers and involves the maintenance crew.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Adjust Front Suspension Pos 2 DA 433

    Uploaded by

    kurniarung oceanda
    40 views4 pages
    This JSEA document provides a 3-step job safety analysis for adjusting the front suspension on a DA 433 machine at the Wahana Coal Mine project workshop. The steps are: 1) preparation and isolation of the machine, 2) adjusting the suspension, and 3) finishing work. Hazards identified include slipping, falling, impacts, tool breakage, oil spills, and high-pressure nitrogen. Controls include following PPE standards, using danger tags, ensuring tools are used correctly, having spill containment, and using the service manual for suspension procedures. The JSEA was prepared and approved by safety and operations managers and involves the maintenance crew.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This JSEA document provides a 3-step job safety analysis for adjusting the front suspension on a DA 433 machine at the Wahana Coal Mine project workshop. The steps are: 1) preparation and isolation of the machine, 2) adjusting the suspension, and 3) finishing work. Hazards identified include slipping, falling, impacts, tool breakage, oil spills, and high-pressure nitrogen. Controls include following PPE standards, using danger tags, ensuring tools are used correctly, having spill containment, and using the service manual for suspension procedures. The JSEA was prepared and approved by safety and operations managers and involves the maintenance crew.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    40 views4 pages

    Adjust Front Suspension Pos 2 DA 433

    Uploaded by

    kurniarung oceanda
    This JSEA document provides a 3-step job safety analysis for adjusting the front suspension on a DA 433 machine at the Wahana Coal Mine project workshop. The steps are: 1) preparation and isolation of the machine, 2) adjusting the suspension, and 3) finishing work. Hazards identified include slipping, falling, impacts, tool breakage, oil spills, and high-pressure nitrogen. Controls include following PPE standards, using danger tags, ensuring tools are used correctly, having spill containment, and using the service manual for suspension procedures. The JSEA was prepared and approved by safety and operations managers and involves the maintenance crew.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 4

    Discipline Document Number

    Mechanical ID205-JSEA-M&E-001(02)

    WAHANA COAL MINE


    Department PROJECT Next Revision Date
    MAINTENANCE
    ID 205 December 2009

    JSEA

    ADJUST FRONT SUSPENSION POS 2 DA 433

    APPLICABLE FOR

    WAHANA COAL MINE PROJECT

    APPROVAL SHEET

    Name Title Date Signature

    Rudy P Purnama HSEQ Manager

    Phil Naughton Operations Manager

    Frans Nugroho Client / KTT

    REVISION DETAILS

    Rev. Date Revision Status Checked by Initial


    01 24-Jan-07 1st Issue Rudi Purnama
    02 05-May-09 2nd Issue Rudi Purnama

    Paper copies are uncontrolled. The controlled version of this document is on the electronic file at HSEQ Department
    PT. Leighton Contractors Indonesia

    JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET

    Division Office / Project: Maintenance / Wahana Coal Mine Project Tools and or Equipment required: JSEA No: ID205-JSEA-M&E-001(02)

    Job Location & Details: Workshop – Adjust Front Suspension Pos 2 DA 433 - PPE Date Prepared:
    - Nitrogen
    JSEA Participants: Maintenance crew - Tool suspensi 24 Januari 2007
    - Spanner
          - ladder Approved by PM:
    - Oil tray
    Responsible Supervisor: Supiansyah - Tyre ckock      
         
          Date:      

    JOB STEP HAZARDS IDENTIFIED CONTROLS REQUIRED (Eg. Remove overhead cable or isolate/sheath ACTION BY/RECORD
    (Eg. Set Up Crane) (Eg. Electrocution from 11Kv Cables) overhead or monitor with spotter) Training PPE Needs (Eg. Supervisor)
    1. Persiapan / Preparation 1.1. Tergelincir (Slip) 1.1.1. Memakai alat pelindung diri sesuai dengan standart dan benar (Wearing All Personal involve in job

    Oct 2009 Page 2 of 4 ID205-HSE-FM-021(01)


    PT. Leighton Contractors Indonesia

    (Isolation of the machine) 1.2. Unit tidak di isolasi (No isolation PPE correctly as standart)
    of unit) 1.2.1. Memasang personal danger tag (Set danger tag)
    1.3. Kejatuhan (falling) 1.3.1. Menjaga kebersihan area kerja (House keeping area)
    1.4. Terjepit (Impacted) 1.5.1. Memastikan pemeriksaan penggunaan peralatan dengan benar (Ensure
    1.5. Peralatan rusak (Tools broken) inspection and using tools correct)
    2. Penyetelan suspensi (Adjust 2.1. Tergelincir (Slip) 2.1.1. Memakai alat pelindung diri sesuai dengan standart dan benar (Wearing
    suspension) PPE correctly as standart) All Personal involve in job
    2.2. Terjatuh dan kejatuhan (Falling)
    2.3. Terjepit (Impacted) 2.1.1. Menjaga kebersihan area kerja (House keeping area)
    2.4. Peralatan rusak (Tools broken) 2.4.1. Memastikan penggunaan alat-alat dengan benar (Ensure that using
    tools correctly)
    2.5. Tumpahan oli (oil spill)
    2.5.1. Menyediakan tempat penampungan oli, dan segera di bersihkan
    2.6. Suspensi cylinder berada di (Provide oil trap and need to clean)
    bawah tekanan (Suspension
    cylinder under high pressure) 2.6.1. Menggunakan buku manual caterpilar untuk prosedur pengecekan atau
    mengisi suspensi cylinder (Use caterpillar service manual for correct
    2.7. Tekanan nitrogen silinder di procedure to check/charge the suspension)
    bawah 2500psi (Nitrogen cylinder
    under 2500psi pressure) 2.7.1 Penanganan yang benar (Correctly handling)
    Memastikan peralatan cylinder (Trolley, clamps,dll)/Restraining of SAS
    cylinder (Trolley,clamps,etc)
    3. Pekerjaan selesai (Finished 3.1. Tanda bahaya tidak di ambil dari 3.1.1. Melepas tanda bahaya (Remove danger tag) All Personal involve in job
    work) unit (Danger tag no taken from 3.1.2. Membersihkan area kerja (Clean work area)
    unit)

    JSEA PARTICIPANTS (included all personnel involved on the jobs e.g., operator, spotter, mechanics, rigger, etc)

    NO NAME (nama) TITLE (jabatan) SIGNATURE (tanda tangan) REMARK (catatan)

    Oct 2009 Page 3 of 4 ID205-HSE-FM-021(01)


    PT. Leighton Contractors Indonesia

    1.

    2.

    3.

    4.

    5.

    6.

    7.

    8.

    9.

    10.

    11.

    12.

    13.

    14.

    15.

    CONDUCTED BY (disosialisasikan oleh) : POSITION (jabatan) :

    Oct 2009 Page 4 of 4 ID205-HSE-FM-021(01)

    You might also like