Scribd Logo
Upload

Welcome to Scribd!

  • 179 views

    Summative Test-Tvl-Ia Smaw 11

    Uploaded by

    isagani abril
    The document appears to be a remedial test from the Division of Negros Oriental Region VII Candugay High School. It contains 10 multiple choice questions testing welding knowledge, including questions about causes of undercut, welding procedure specifications, filler passes, blowholes, weld defects, poor penetration, appropriate amperage ranges for different electrodes and diameters.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Summative Test-Tvl-Ia Smaw 11

    Uploaded by

    isagani abril
    179 views1 page
    The document appears to be a remedial test from the Division of Negros Oriental Region VII Candugay High School. It contains 10 multiple choice questions testing welding knowledge, including questions about causes of undercut, welding procedure specifications, filler passes, blowholes, weld defects, poor penetration, appropriate amperage ranges for different electrodes and diameters.

    Original Description:

    gng

    Original Title

    Summative Test-tvl-ia Smaw 11

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document appears to be a remedial test from the Division of Negros Oriental Region VII Candugay High School. It contains 10 multiple choice questions testing welding knowledge, including questions about causes of undercut, welding procedure specifications, filler passes, blowholes, weld defects, poor penetration, appropriate amperage ranges for different electrodes and diameters.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    179 views1 page

    Summative Test-Tvl-Ia Smaw 11

    Uploaded by

    isagani abril
    The document appears to be a remedial test from the Division of Negros Oriental Region VII Candugay High School. It contains 10 multiple choice questions testing welding knowledge, including questions about causes of undercut, welding procedure specifications, filler passes, blowholes, weld defects, poor penetration, appropriate amperage ranges for different electrodes and diameters.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 1

    DEPARTMENT OF EDUCATION

    DIVISION OF NEGROS ORIENTAL


    REGION VII
    CANDUGAY HIGH SCHOOL
    CANDUGAY, CASALAAN, SIATON, NEGROS ORIENTAL

    TVL-IA SMAW-11
    Remedial test

    Multiple Choice:
    Read each question carefully and choose the best answer. White your answers in
    your paper.

    1. The most common cause of undercut in a weld is too?


    a. High an arc b. High a current c. Short an arc d. Low of current

    2. The welding procedure specifications consist of the ff.


    a. Essential variable b. Non- essential variable
    c. Supplementary essential variable when required d. All of the above

    3. A material that is being added after the root pass is called?


    a. Final capping b. filler pass c. hot pass d. all of these

    4. What is the possible cause of a Blow Hole welding defect?


    a. Improper manipulation b. Over travelling speed.
    c. Improper groove shape. d. Too large weaving width

    5. Which of the following weld defects does not have any tolerance for acceptance? a.
    Under cut b. Crack c. Porosity d. Slug inclusion

    6. Which of the following can cause poor penetration and incomplete fusion in welding?
    a. Temperature is too hot b. Gap between two plates is too small
    c. Improper electrode size and type d. Improper manipulating of electrode

    7. Which of the following is the most common cause of undercut in a weld?


    a. High an arc b. High current c. Short an arc d. Low of current

    8. Which corrective actions should be followed in-order to eliminate distortion?


    a. Use proper bead sequencing
    b. Tack or clamp parts securely
    c. Use low hydrogen type electrode with higher basicity.
    d. Both A and B

    9. Which of the following amperage should be followed using an electrode 6011, with a
    diameter of 3/32?
    a. 30-40 b.100-150 c. 45-90 d. 150-155

    10. Ener is doing the final pass for his workpiece, he is using electrode 7018 having a
    diameter of 3/32. Which amperage range should he follow?
    a. 60-100 b. 30-50 c. 100-125 d. none of the above

    You might also like