Sika - Sikagrout 215

Technical Data Sheet
Edition 6, 2009
Identification no.
02 02 01 01 001 0 000054
Version no. 0010
®
Sikagrout 215 (new)
®
Sikagrout 215 (new)
High Precision, General Purpose, Non-Shrink Cementitious
Grout
Description A non shrink, cementitious premixed grout with extended working time to suit local
ambient temperatures. Flowable grout with high resistance to cement wash-out
Construction
when placed under water.
Complies to Corps of Engineer’s specification CRD C-621 and ASTM C-1107
Use For grouting over a wide range of applications:

Anchor bolts
Machine bedding/base plates
Supporting bridge bearing pads
Pre-cast concrete sections
Dry pack applications
Cavities, gaps and recesses.
For grouting method of concrete repair
Marine structure :
also recommended for repairing structure underwater and in tidal zone grouting.
Application repair of : - Bridge piers.
- Concrete piles.
- Harbour walls.
- Jetty pillars.
Advantages Easy to use, just add water

Good flow characteristic
Adjustable consistency
Rapid strength development
Impact and vibration resistant
Shrinkage compensated
High final strength
Non-Corrosive
Non-Toxic
3
Consumption ~ 1.920 kg/m of mortar.
Instruction for Use

Surface Preparation Remove dirt, oil, grease, loose material and other bond-inhibiting materials.
Anchor bolts to be grouted must be degreased with suitable solvent.
Concrete must be sound and roughened to promote mechanical adhesion.
Prior to pouring, surface must be wetted to saturated surface dry
Forming For flowable grout, construct forms to retain grout without leakage.
Forms should be lined or coated with bond-breaker for easy removal.
Forms should be sufficiently high to accommodate head of grout.
Where grout tight form is difficult to achieve, use Sika Grout 215 (new) in dry pack
consistency.
Mixing Put appropriate quantity of water (depend on the required consistency) into a mixing
vessel. Add slowly the total contents of SikaGrout 215 (new) while mixing. Mix
continuously for 3 minutes to achieve an even consistency. Use a mechanically low
speed drill (400–600 rpm) with mixing paddle or appropriately sized mortar mixer.
Back
Table of Contents
1 Sikagrout® 215 (new) 1/3

Application Within 25 minutes after mixing, place grout into forms from one side to avoid air
entrapment. Do not vibrate. Use a suitable head box of 150–200 mm and maintain
the grout head at all times to ensure a continuous flow. Gentle tapping or pulling
loops of wire from one side may assist the flow of the mortar under difficult working
conditions.
Curing Wet cure for a minimum 3 days with wet hessian, plastic sheet or apply a curing
compound (Antisol)
Limitation Minimum application thickness : 10 mm

Recommended thickness of Sika Grout 215 (new) in one pour is 20 mm to 50 mm.
If the application thickness exceeds 100 mm, special procedure must be taken to
anticipate temperature rise. Iced water, add coarse aggregate to the mix (max.
50% by powder weight), or both of them may be used to eliminate temperature
rise. Keep the materials and substrate temperature lower than 30o C. Variations in
cement could cause shade differences in colour of the mortar. In the case of
addition with coarse aggregate, it is advised to conduct trial mix to check influence
of coarse aggregate addition on grout workability and strength. 8 to 10-mm size
aggregate is found to be the most suitable size for this addition.
Contact Sika Technical Service for under water application.

Technical Data
Form Powder
Color Grey
Flow Condition Flowable
(Mod J cone : 6-12 sec)
Water requirement 4.00
(Litres per 25 kg bag)
Yield 13.00
(Litres per 25 kg bag)
Mix Density Approx. 2.26 kg/ltr
Compressive Strength
(ASTM C-109) 1 days 240 kg/cm2
3 days 410 kg/cm2
7 days 530 kg/cm2
28 days 650 kg/cm2
Flexural Strength
(ASTM C-348) 28 days >60 kg/cm2
Tensile Strength
(ASTM C-496) 28 days >35 kg/cm2
Bond Strength
2
to concrete 28 days >15 kg/cm (concrete failure, over mechanically roughened concrete surface)
2
to grout 28 days >25 kg/cm (over mechanically roughened grout surface)
Expansion (ASTM C-940) 0.30 – 1.40 %
Initial Setting Time 4 – 8 hours

(at 27°C)
Shelf Life 9 months when unopened and stored in dry condition
Packaging 25 kg bag

Handling ■ Avoid contact with skin and eyes
■ Wear protective gloves and eye protection during work
Precautions: ■ If skin contact occurs, wash skin thoroughly
■ If in eyes, hold eyes open, flood with warm water and seek medical attention
without delay.
Legal Notes The information, and, in particular, the recommendations relating to the application and end-use of Sika
products, are given in good faith based on Sika’s current knowledge and experience of the product when
properly stored, handled and applied under normal conditions in accordances with Sika’s
recommendations. In practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising
out of any legal relationship whatsoever, can be inferred either from this information, or from any written
recommendations, or from any other advice offered. The user of the product must test the product’s
suitability for the intended application and purpose. Sika reserves the right to change the properties of its
products. The proprietary rights of third parties must be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which will be supplied on request.
Construction
PT. Sika Indonesia Branches

Jl. Raya Cibinong- Bekasi km. 20 Surabaya :
Limusnunggal- Cileungsi Puri Niaga Blok G No. 29, Jl. Raya Rungkut Menanggal 11, Surabaya
Tel : 031-8690202 ; Fax : 031-8682123
BOGOR 16820 - Indonesia
Medan :
Tel. +62 21 8230025 Jl. Pancing / Jl. Willem Iskandar No.75 & 75 A, Kec. Medan Tembung
Fax +62 21 8230026 Tel : 061- 6619500; Fax : (061) 6619400
Website : www.sika.co. id Batam :
e-mail: [email protected] Jl. Laksamana Bintan, Komp. Bumi Riau Makmur Blok E No.3, Sungai Panas
Tel : (0778) 424928; Fax : (0778) 450189

Sika - Sikagrout 215

Uploaded by

Copyright:

Available Formats

Sika - Sikagrout 215

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sika - Sikagrout 215

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

when placed under water.

Complies to Corps of Engineer’s specification CRD C-621 and ASTM C-1107

Use For grouting over a wide range of applications:

Advantages Easy to use, just add water

Instruction for Use

1 Sikagrout® 215 (new) 1/3

Limitation Minimum application thickness : 10 mm

Contact Sika Technical Service for under water application.

Initial Setting Time 4 – 8 hours

2 Sikagrout® 215 (new) 2/3

PT. Sika Indonesia Branches

3 Sikagrout® 215 (new) 3/3

You might also like