Use of Instructions Customer Support

Warning. Note. ABB Instrumentation provides a comprehensive after sales service via a
An instruction that draws attention Clarification of an instruction or Worldwide Service Organization. Contact one of the following offices for details on
to the risk of injury or death. additional information. your nearest Service and Repair Centre.
Caution. Information. United Kingdom
An instruction that draws attention Further reference for more detailed ABB Instrumentation Limited
to the risk of damage to the product, information or technical details. Tel: +44 (0)1480 475321
process or surroundings. Fax: +44 (0)1480 470787
Although Warning hazards are related to personal injury, and Caution hazards United States of America
are associated with equipment or property damage, it must be understood that ABB Instrumentation Inc.
operation of damaged equipment could, under certain operational conditions, Tel: +1 716 2926050
result in degraded process system performance leading to personal injury or Fax: +1 716 2736207
death. Therefore, comply fully with all Warning and Caution notices.
Information in this manual is intended only to assist our customers in the efficient
operation of our equipment. Use of this manual for any other purpose is
specifically prohibited and its contents are not to be reproduced in full or part
without prior approval of Technical Communications Department, ABB
Instrumentation Ltd.
Client Warranty
Health and Safety
To ensure that our products are safe and without risk to health, the following Prior to installation, the equipment referred to in this manual must be stored
points must be noted: in a clean, dry environment, in accordance with the Company's published
specification. Periodic checks must be made on the equipment's condition.
1. The relevant sections of these instructions must be read carefully before
proceeding. In the event of a failure under warranty, the following documentation must be
provided as substantiation:
2. Warning labels on containers and packages must be observed.
3. Installation, operation, maintenance and servicing must only be carried out 1. A listing evidencing process operation and alarm logs at time of failure.
by suitably trained personnel and in accordance with the information 2. Copies of operating and maintenance records relating to the alleged faulty
given. unit.
4. Normal safety precautions must be taken to avoid the possibility of an
accident occurring when operating in conditions of high pressure and/or
temperature.
5. Chemicals must be stored away from heat, protected from temperature
extremes and powders kept dry. Normal safe handling procedures must be
used.
6. When disposing of chemicals ensure that no two chemicals are mixed.
Safety advice concerning the use of the equipment described in this manual
or any relevant hazard data sheets (where applicable) may be obtained from
the Company address on the back cover, together with servicing and spares
ABB Instrumentation Fax: +39 (0) 344 58278 Fax: +1 716 273 6207 Fax: +44 (0) 1480 217948
Tel: +39 (0) 344 58111 Tel: Tel: +1 716 292 6050 Tel: +44 (0) 1480 475321
Italy USA England, PE19 3EU
Como New York 14602-0550 Cambs.
22016 Lenno PO Box 20550, Rochester St. Neots
ABB Kent-Taylor SpA ABB Instrumentation Inc. ABB Instrumentation Ltd.
Printed in UK (3.99) © ABB 1999
without notice.
to modify the information contained herein
product improvement and the right is reserved
The Company's policy is one of continuous
IM/P871
Issue 4
Pressure Transmitters
User Guide DATUM P871 and P881
1 INTRODUCTION …2 MECHANICAL INSTALLATION

2.4 Mounting – Figs. 2.2

Warning.
Borehole Reservoir Tank
• The pressure range must be compatible with the maximum pressure being
measured.
• The pressure media must be compatible with the transmitter wetted parts
listed in these instructions.
• Liquid must not be allowed to freeze in the pressure port.
P881
• Exposed ends of cables must be free from moisture. P881
• P881: the gasket must be fitted under the electrical connector.
• P871: the sensor breather tube must not be blocked.
P871
• Wetted parts:
P881 17 – 4 PH stainless steel plus Nickle Braze to BS1845 : NK3/HTN2.
P871 17 – 4 PH stainless steel plus Nickle Braze to BS1845 : NK3/HTN2.
316/321 Stainless steel body tube, polyurethane cable. P871 P871
Fig. 2.2 Mounting Options
The DATUM P871 and P881 Pressure Sensors are ideal for applications where a
When mounting the P871, wrap the cable a minimum of two turns around a
conventional transmitter is too expensive and over specified.
structural support (minimum bend radius 50mm (1.97 in.)) and secure using a
The DATUM P881 is a low-cost simple transducer which, when used with the suitable cable clamp. Avoid sharp edges which may damage or deform the cable.
DATUM L150/L160 indicators, gives a complete stand-alone pressure indicator/
transmitter solution. 3 ELECTRICAL INSTALLATION
The DATUM P871 submersible sensor, with its IP68 integrity, is suitable for
pressure measurement in adverse conditions or total immersion for the Information.To reduce the effects of lightning strikes the sensors are
measurement of liquid level/depth. fitted with suppression devices providing surge immunity to IEC 801 Part 5. It
is recommended that the receiving equipment be fitted with a Lightning
Both types can be used as a primary sensor, utilizing one of ABB’s other products, Protection Unit (LPU) at the point of cable entry into the building.
e.g. COMMANDER 300 and 310 Universal Process Controllers.
3.1 Electrical Connections
2 MECHANICAL INSTALLATION
2.1 Pressure Connections Electrical Connections +ve –ve case earth
P871: Gl/8 internal to BS 2779 compatible with ISO 228. Fitted with Nosecone.
P871 Red Blue Green/braided screen
P881: Gl/4 internal, Gl/4 external, 1/4 – 18NPT external, G1/2A pressure gauge,
7
/16 – 20UNF external, G1/4 ERMETO, 1/ 8 – 27NPT external, R1/4 external P881 Pin 1 Pin 2 Pin 4
or G1/8 internal.

2.2 Environmental Limits Electrical Specifications Rated Min./Max. Milliamps

• Temperature limits: P871 –20°C to 55°C. P881 –40 °C to 125 °C.
P871
• P871 rated to IP68 24V d.c. 7 to 35 4 to 20
P881
Caution. In high humidity environments, condensation must be
prevented from entering the sensor vent (breather) tube. Table 3.1 Electrical Connections and Specifications

2.3 Dimensions – Figs. 2.1 3.2 Grounding

All versions should be grounded by the installation pipework. If this is not possible,
Dimensions mm (inches) the sensor should be grounded at the instrumentation end via the appropriate pin
68.2 (2.69) Max. Absolute or green lead. For maximum protection against RFI all versions should be installed
64.1 ( 2.52) Max. Gauge using screened cable with the screen earthed at the instrumentation end.
26 (1.02)
3.3 Resistive Loading
Mini 4-pole Connector The total permissible resistive load in the loop (to include all the cable resistance)
can be from zero to 50 x (supply volts –7) ohms, eg. with a 24V d.c. supply the
31 (1.22) permissible load is from zero up to 850Ω, see Fig. 6.1.
Max.
G 1/4 External thread process connector
shown for example only. + +
Power
For connector dimensions – see 15 (0.59) O.D.
Specification Sheet SS/P881 Supply Transmitter
12 to 36Vdc – –
36 (1.42) Max. Resistive Load

Fig. 6.1 Resistive Load

3.4 Applying Power
Before applying power, ensure the correct polarity and excitation levels are
35 (1.38) applied.

DIN 43650 Connector

3.5 Calibration
Transmitters are calibrated to a fixed range at time of order, identified by the
18 (0.71) O.D. identification code marked on the sensor housing – see specification sheets
P881 Sensor SS/P851 and SS/P881.

27.2 (1.07) 103 (4.06) Max. 62 (2.44) Max.

4 MAINTENANCE
4.1 Routine Inspection
Limited to periodic inspection of the cable and connector to ensure that these are
neither damaged nor softened by incompatible liquid.

81.0 (3.19) Max. 4.2 Repair

P871 Sensor The instruments cannot be repaired locally. If damaged, return to the Company at
the address shown on the back page, or to accredited dealers, if a
Fig. 2.1 Sensor Dimensions replacement/repair is required.
1