FT-757GX “YAESU MUSEN CO., LTD. €.P.0. BOX 1500 TOKYO, JAPANCONTENTS (Page) ERRATA FOR THE FT-757GX OPERATING MANUAL... 2.0... cece eee ee . a 2 SOLDERING AND DESOLDERING TECHNIQUE ees 3 PERFORMANCE IMPROVEMENT MODIFICATIONS 6 CAT SYSTEM INTERFACE DATA MANUAL 9 OUTER COVER REMOVAL AND UNIT ACCESS SERVICE AND ALIGNMENT SEMICONDUCTOR LOCATIONS eee eee ceeeee SIGNAL PATHS ......... eee peepoass5enn 24 COMPONENT APPLICATIONS FP-757GX/HD SCHEMATIC DIAGRAMS. : ae qopso095000q CONNECTION DIAGRAM ........ Peter e ree tee ee 34 PARTS LAYOUTS, SCHEMATICS, SIGNAL LEVELS AND VOLTAGE CHARTS: RF UNIT . LOCAL UNIT LPF UNIT .. DISPLAY UNIT DIALUNIT ........ 100W PA UNIT .. 10W PA UNIT . KEYER UNIT . Beet ceeeeeeee SWITCH UNIT A, SWITCH UNIT B, KEYER CONTROL UNIT FT-757GX/SX PARTS LIST . FP-757GX PARTS LIST ............... FP-7S7HD PARTS LIST ...............4FT-757GX This manual is intended to serve as a technical supplement to the FT-757GX Operating Manual. Detailed information regarding functions, installation, interconnections, and operation has been provided in the Operating Manual, and is not reprinted herein. Therefore, this Technical Supplement is not intended to serve as an independent reference, but to be used in conjunction with the information provided in the Operating Manual. Because there are nearly four hundred and fifty semiconductor devices in the FT-757GX, circuit descrip- tion information is provided in the form of numerous block diagrams and a complete Component Applica- tions list. It is our hope that this manner of providing functional information will prove to be more convenient for the owner and technician than would a lengthy verbal description. Those readers who are not familiar with the basic types of analog and digital circuits that serve as the building blocks of the FT-757GX are encouraged to study instructional material, such as that contained in handbooks on amateur radio and digital circuit design, before attempting to understand the design of the FT-757GX. Each block in the block diagrams represents one such basic circuit, while the Component Applications list provides additional details for each semiconductor. Specific circuit details are provided in the schematic diagrams. ‘The few modifications that have been developed for the FT-757GX since the start of production are all included in this Manual. All of these modifications have been incorporated from Production Lot 5 onwards, while some have been incorporated in some Lot 4 sets. While we believe this technical information is correct and factual, Yaesu assumes no liability for damage that may result from typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated. Yaesu Musen reserves the right to make changes in the circuitry of this transceiver, in the interest of technological improvement, without notification of the owner.ERRATA FOR THE FT-757GX OPERATING MANUAL The following corrections apply to the first and second printings of the Operating Manual, with the code numbers E3890183 and E3890183A, re- spectively, on the back of the rear cover. First Printing Only: KEY plug requirements The KEY jack on the rear panel of the FT-757GX will only accept a 3-conductor phone plug for connection of a CW key, keying paddles or an ae g extemal keyer. If a 2-conductor plug is used, the outer (ground) contact will be shorted to the sleeve ring (dot) contact, and proper CW transmission will not be possible. The information stating otherwise on pages 13 (KEYER switch description), 20 (MANUAL KEY Plug drawing), and 28 (middle of second paragraph under CW Transmission instructions) is in error and should be corrected accordingly, ape ES First and Second Printings: QSK Linear Amplifier Connections ‘The two lower interconnection diagrams on page 19 do not show the connections for the changeover relay closure delay signal (“INH” in the FT- 757GX), which is required in order to protect the QSK amplifier from premature excitation when the transceiver is keyed, until the changeover relay contacts in the linear are properly seated, To correct the diagrams, another connection must be shown to the rear panel of the Linear in the upper diagram, and a third conductor must be shown in the QSK Linear Amplifier Connection Cable drawing at the lower right, one end of which connects to pin 8 of the BAND DATA plug. Later printings of the Operating Manual show screw terminal connections on the Linear, and no RCA plug on the Linear end of the cable (just free wires). The number of the (optional) cable is changed to T9101295A. Schematic Diagram Correction: R269 on the RF UNIT Early printings of the Schematic Diagram of the RF UNIT show the value of R269 (bottom center, near J27) as 470 ohms. This should be 150 ohms.SOLDERING AND DESOLDERING TECHNIQUE The FT-757GX circuit boards are tough, but mis- handling during soldering can cause circuit traces, to “lift.” While this does not cause permanent damage to the board, much servicing trouble can result, because of the tendency for this lifted trace to break. A few simple precautions will keep your circuit boards in A-1 condition. 1. Use only a 12 to 30-watt chisel-tip soldering iron, with the tip grounded or isolated from AC and DC potential. Voltage at the tip can easily destroy CMOS components. 2. Use only the minimum amount of heat neces- sary to remove a component, or to cause the solder to “flow” when installing a new com- ponent. 3. USE ONLY 60/40 ROSIN CORE SOLDER. 4. Use solder removing braid and flux to absorb excess solder before installing a new com- ponent. A solder sucker can also be used, but most be handled with care to avoid lifting traces, 5. Do not attempt to remove DIP ICs without first cutting all of the pins on the component side of the board, unless you have the correct desoldering equipment (springdoaded clamp and all-pin desoldering tip). If you do lift a trace, don't worry! Read on to find out how to repair traces like a pro. NOTES ON USE OF CMOS COMPONENTS: ‘As CMOS devices are extremely sensitive to damage from static electricity, special precautions must be observed. In storage, use only conductive sponge specially designed for CMOS components, When installing a CMOS part in a socket, or on a circuit board, be certain that the power is off. In addition, the technician should rest his hand on the chassis as the component is inserted, so as to place his hand at the same potential as the chassis (better to discharge small amounts of static electricity through your fingers than through a $5 IC !). ‘When soldering a CMOS part onto a circuit board, use a low-wattage iron, and be sure to ground the tip with a clip lead, if the tip is not grounded through a three-wire power cord. INSERTION OF PARTS ON CIRCUIT BOARDS Alll of the below are acceptable ways of inserting components into circuit board mounting holes. = (a) Bend leads slightly RE 0) sirihtin mounting (0) Vertical mounting (d)_ Preformed disc ceramic = capacitor s- (©) Preformed resistor, diode, ete.BASIC SOLDERING PRACTICE solder. The tip of the iron should be thoroughly tinned and wiped clean of excess solder. p (1) Prepare soldering iron and eT + surface to be soldered. Do (2) Apply soldering iron to \ not press the iron into the surface, (3) Apply solder to junction of iron and heated surface, (4) When enough solder is applied, remove solder. Continue to apply heat just until solder flows cleanly. Do not apply more heat + (5) Remove iron from work. aN than necessary for good solder flow. Soldering to terminal posts: (Be certain to apply heat to both post and wire.) ®) ‘i a EXAMPLES OF POOR SOLDERING PRACTICE. Unwanted solder bridge con- necting two tracks (caused by use of too much solder) —S) “Cold joint” (caused by in- sufficient heat to part of work, resulting in poor solder flow) a Unstable joint (caused by in- sufficient heat or solder) Proper solder A smooth fillet of solder surrounds the lead and just covers the foil pad. cai If you have previously lifted a trace, make an etch cut on each side of the lifted trace as shown in the drawing, and install a wire bridge. Coat Gut Area With Eastman 910 Alter Soldering Wire BridgeTYPICAL PART FAILURES, CAUSES AND SYMPTOMS PARTS CAUSE OF TROUBLE ‘SYMPTOMS Semiconductors High supply voltage Short or open circuit (IC, FET, TR) Open circuit Output decreases to 1/2 at 80°C Excessive drive Internal noise High temperature Instability MOS FET Static electricity Total failure MOS IC Short or open circuit Crystal ‘Shock No oscillation Crystal filter High temperature Off frequency Aging Frequency drift Filter bandpass change Shock, forced rotation Resistor Excessive power ‘Component burned High temperature Value changed Open circuit Potentiometer Excessive power Component bumed Shock Open circuit Dust or oil Noise Wear Unsmooth rotation Capacitor Excess voltage Shorted High temperature Leakage Aging Open/decreased capacitance Variable capacitor Ratings exceeded Shorted Trimmer capacitor Dust between plates ‘Leakage Unsmooth rotation Dust or oil on contacts Coils Ratings exceeded ‘Open or short circuit Misadjusted Leakage or shorted tums Core or bobbin broken Detuned Switch Ratings exceeded Poor contact Aging Unsmooth operation Dust or oil Open circuit Relay Ratings exceeded Coil open Humidity Poor or intermittent contact NoisePERFORMANCE IMPROVEMENT MODIFICATIONS Serial numbers are composed of a letter and a number, indicating the date of manufacture, followed by six digits, The first two digits (closest to the date code) are the Production Lot number. So, for example, serial number 0C123456 is from Production Lot 12, set number 3456. Before making any modification, make sure that it applies to the Lot number of the particular transceiver being modified. Also, before making any modification, check to see if it has already been carried out by a Yaesu agent, dealer or previous owner, QSK Keying Stability The following modification may be made to improve the stability of QSK operation, if it is found to be unstable. This modification has already been carried out in some Lot 4 trans. ceivers, and in all transceivers having serial numbers above XX050000 (Lot 5), The diagrams below and on the following pages indicate the changes to be carried out on the PA. Unit and RF Unit during the following steps: ! s2o10/eai 1 Referring to page 11, disconnect the trans- | ceiver from the power source and remove the | covers, i Referring to the 100W PA Unit diagram on the following page, locate Py; and cut the blue wire at pin 5 (INH signal) of this plug. Do not disturb any other connections on this Unit. Now referring to the RF Unit diagram on the following page, solder a S cm extension wire to the end of the blue wire removed from the 100W PA Unit, and then carefully insulate the splice with vinyl tape. Solder the other end of the extension to the end of Ry2s7 exposed on the component side of the RF Unit. Route the blue wire carefully so that it will not be pinched when replacing ihe boards and covers, and then reassemble the parts removed. This completes the modification, 60S? 1OKA Bsv 8003/42 1 100w Pa unit ee ir 1097 oo 096 Ito ese 2.20.Blue [... unit Component side !OOW PA UNIT 1a we Sen) SAE slr 8 ope = From Loca. uN {a © Npnesr zon Ws 2D Cr ery RF UNIT Component side | |W Filter Isolation In some sets prior to Lot 6, IF signal leakage has 3. Now connect the free end of the extended been found to occur around the CW filter during jumper to the cathode of diode Digg (near CW-N reception with the FT-757GX. The cause of VRjoos )- The cathode lead of this diode is the this problem is insufficient isolation within FM upper (exposed) lead. detection subsystem IC Qzo22 (MC3359) on the RF Unit during CW operation. To remedy this 4. Replace the bottom cover and reconnect the Problem the following modification will remove power supply. This completes the modifica- the supply voltage from FM 2nd IF signal buffer tion. Qiorr, except during FM operation. This modification has already been carried out in all sets from the beginning of Lot 6 onwards, as well as in | some of the later sets in Lot 5. ‘(make on “X over 78V) > FM8V 1. Disconnect the power supply, and remove the Ri099 1000. bottom cover of the transceiver to gain access aoe to the component side of the RF Unit. CHISO 100pF 2. Referring to the drawing below, cut jumper Wire R near the end closest to VRioio and VRioi- Splice a 3 to 5 cm length of hookup ci Coe wire to the free end of the jumper, and solder ieclat and carefully tape the splice. mothe $8220 Yee” Bar O OM Ut Pe ae Madd 8 asf ty He YY gage tr mths, fe 3 mas th58o< 8 Bean z eae gare peor ee mee nda cw Ld, Sse io B # nie oe 2 2 ot ah) elit eh x03 3 fy Se e v4 oO; " Jez wat tn Wee ae) el FA teeta) Diy 7 XFOS Be iq) ISOLOER and TAPE |, Pet Oia 2 3 ren J? SL “0 y 091 TE g T na Po | o a Boy Obes Cpe iam, st ane Fu Bd 238 8G gecieacirign & ERG! tt EN@) a Td VRE 8 m0 *y arrives frees RF UNI 8 yee 2) gets beg eves Component side ITCAT SYSTEM SERIAL INTERFACE DATA MANUAL The CAT (Computer-Aided Transceiver) System in the FT-757GX allows use of an external micro- computer to control the memory and operating frequency functions of the transceiver. Control signals are passed to the transceiver on a serial data line, accessible at the EXT CNTL jack on the rear of the transceiver. Yaesu offers a number of different Interface Units for making the neces- EXT CNTL PINOUT EXTERNAL INTERFACE sary data format conversions to connect some of the common brands of microcomputers, Software is provided with some of the Yaesu Interface Units when they are designed for use with one specific microcomputer. The EXT CNTL jack also provides access to the receiver AGC line, for application in user’s programs, Fr-7876x a4 oe PIN NAME DESCRIPTION 1 GND Common ground for signal lines and shielding. 20 st Serial Input: accepts standard TTL-level data, 3 AG Automatic Gain Control: analog signal output ranging from +0.4V DC during strong signal reception, to #2.6V DC when no signal is being received. DATA TIMING FORMAT (4800 bits/second) sunt byte Fomai [a [8H [ [we [os [oe Ts [oe [pr] Sop - | Cos ae nig] bf aos soy Command (“Tap af a aD LH) ssyeerunmeer ———eLt* | Tt Tnetaction 0~100 me max. Shown below are examples of two basic types of commands. Each is five bytes in length. Frequency Enter Command (Example: to set 14.25000 MHz) Frequency Step Command (Example: to step up 500 kHz) CC ET TT T Frequency —__| tticton Parmeter __|inkmstion Faametet —"| (en se) (Gummy day 716000)As illustrated in the Frequency Enter Command example, frequency parameter data is sent least- significant digit first. The Frequency Step Com- mand example shows how dummy data (“99") is required in all other commands, preceding the instruction byte. Once the S-byte command has been sent to the transceiver, it will respond with the appropriate change indicated on the front panel display, If not, an error has occurred either in the data sent or in the interface connection, so these should be inspected before the command is sent to the transceiver again. Note that the controls on the transceiver are not disabled when exercising external control; touching any control on the transceiver that duplicates an externally-controlled function will invalidate function indications on the computer display. The external control program may then have to be reinitialized to clear inva- lidated variables. To avoid problems caused by inadvertent movement of the tuning knob, the D. LOCK command can be programmed to be sent to the transceiver during external control operation PROGRAMMING Gam 7 cv cruf ——xevR COMMAND BYTE CODES va [oom Fa] tuneriow 171| vFoAWFo SPLIT ONena OFF wawvro [x |x |x 5 4] Loe snirg in wo ae [x tes] Egy Mev [x [16 wre memory ea ne opening VFO, s00.uP |x 17 Swoup S00 wt (Band Up) [#8] Sua cow 800 «He (Band Oown) [99] Aswan oot ci cece Data output routines in the external computer may have to be in machine language, as: BASIC and other high-level languages are generally too slow to handle the required routines during data transfer, unless the computer is equipped for 4800-baud output 10 —OUTER COVER REMOVAL ? g CUT oo # LOOSEN ON BOTH SIDES SLIDE FORWARD RF AND LOCAL UNIT ACCESS For access to the solder sides of the RF and Local Units, loosen the screws (marked #) on each side and slid the front panel forward, To remove the RF Unit, the KEY jack nut must be removed using a special wrench (see your Yaesu agent). Disconnect the following plugs from their corresponding jacks on the RF UNIT: Jz;/Pi4, Jau/Pos, Jap/Pos: Jos/Pos. Jou/Po: and J34/Pos Remove the 5 screws in the board and the KEY jack nut. Then note the position of the FWD SET knob, and remove it (it should be replaced in the same position). ieSERVICE AND ALIGNMENT The FT-757GX is carefully designed to allow the knowledgeable operator to make all adjustments required for various station conditions, modes and operator preferences simply from the controls on the front and rear panels, without opening the case of the transceiver. These adjustments are described in the FT-757GX Operating Manual, The following procedures cover the sometimes critical and tedious adjustments that are not normally required once the transceiver has left the factory. We recommend that these adjustments be made only by authorized Yaesu service representa- tives, as many are interdependent and difficult to perform correctly without prior experience with FT-757GX alignment. Without such experience and the proper test equipment, any attempt to make internal adjustments is likely to cause degraded transceiver performance, the correction of which is not covered by the warranty policy when caused by unauthorized internal adjustments. In the unlikely event that a sudden failure occurs during normal operation, do not attempt realign- ment. Such failures are almost always due to the failure of a component, often in an external accessory, or a problem with the antenna system. Once the external connections have all been checked, if the transceiver is still suspect, the Yaesu representative through whom the transceiver was originally purchased should be contacted immediately for instructions regarding repair. Authorized Yaesu service technicians automatically perform complete performance checks and realign- ment of all circuits that may be affected once a faulty component has been replaced, Those who do undertake any of the following alignments are cautioned to proceed only at their own risk, Yaesu must reserve the right to change circuits and alignment procedures in the interest of improved performance, without notifying owners. Under no circumstances should any realignment be attempted unless the normal function and operation of the transceiver are clearly understood, the malfunction has been carefully analyzed and any faulty components replaced, and the need for a specific realignment determined to be absolutely necessary. Procedures not involving adjustments are termed checks, and are included for trouble- shooting purposes. The following test equipment (and thorough familiarity with its use) is required for complete alignment, While most steps do not require all of the equipment listed, the interactions of such adjustments may require that more complex adjustments be performed afterwards. Do not attempt to perform only a single step unless it is clearly isolated electrically from all other steps. Rather, have all test equipment ready before beginning, and follow all of the steps in the order that they are given in each section, During all of the following procedures that call for the transmitter to be activated, a 50-ohm dummy load must be connected to the antenna jack, except where specifically stated otherwise. Also, the WIDTH/SHIFT controls must be set to the 12 o'clock position, the RF gain contro! must be fully clockwise, and the SQL control must be fully counterclockwise, unless stated otherwise. After completing one step, read the following step to determine whether the same test equipment will be required. If not, remove the test equipment (except dummy load and wattmeter) before proceeding. FT-7578X (10 W) Underside of Heatsink 2Alignment Equipment Frequency counter with accuracy of 0.1 ppm to 100 MHz DC voltmeter with at least 10-Megohm input impedance RF voltmeter with at least 5% accuracy to 100 MHz, high impedance, and ranging from 10 mV to 3 Vrms AF millivoltmeter DC milliammeter ranging to $00 mA. XY oscilloscope with 60 MHz bandwidth 100W Pa UNIT FT-7876X RF in-line wattmeter Resistive dummy load, 50 ohms, 15OW; three re- quired for SWR Turndown alignment RF signal generator covering 1-30 MHz, with calibrated output levels from 5 dBu to 100 dBu AF signal generator with calibrated output levels. from I mV to 25 mV FM deviation meter/SINADer and RF sampling coupler (“T") for FM modulator alignment Monitor scope for transmitter output display Linear detector for 1-30 MHz LPF UNIT KEYER UNIT “80S KEVER CONTROL UNIT Underside of Heatsink Chassis Top View LocaL UNIT DIAL UNIT DISPLAY UNIT Sy gi LR unit Chassis Bottom View 3BALIGNMENT LOCAL Unit A. Third LO BPF Remove P,, and connect a 50-ohim load across 3rd LO OUT jack Jzo98, along with the RF voltmeter. Set the transceiver to a CW mode, and while receiving, adjust T2991 and T3993 for maximum deflection on the voltmeter (50 mVrms nominal). B. SSB, AM, CW RX LO Level Connect the RF voltmeter to pin 2 of Qro12 and adjust TCzo92 so that the difference in level be- tween CW transmit and receive is less than 5 mVrms at this point (output level approximately 100 mVrms), C. 45 MHz Bandpass Filter With the transceiver set to the 14 MHz band, connect the RF voltmeter to TPzo9. and adjust Taoo9 and Tapio for maximum voltmeter deflec- tion (more than 80 mVrms). D. 60 MHz Bandpass Filter Set the transceiver to the 21 MHz band, and with the RF voltmeter connected as in the previous step, adjust Tio}: and Tz9)2 for maximum deflection (more than 80 mVrms) E, 45 MHz Tripler Return the transceiver to the 14 MHz band, and connect the RF voltmeter to P2902. Adjust Taoo¢ and To97 for maximum deflection (more than 80 mVrms).. F. 15 MHz Reference Frequency Connect the frequency counter to TPz992 and adjust TC994 for 45 MHz #20 Hz. G. 2nd Local Oscillator Frequency 1. Connect the frequency counter to TP:o97, and tune the transceiver so that the display indicates 14,000.00, Adjust VRaoog so that the counter shows 32.0600 MHz + 20 Hz. Retune the transceiver so that the display shows 13.99.99, and adjust VRjo.a, if necessary, to obtain 32.05901 MHz on the counter. Now retune the transceiver to 14,000.00 and check that the difference in —14 the frequencies shown on the counter are within 990 Hz +5 Hz. H. Carrier Point Connect the frequency counter to Jzoog and adjust the component indicated in the correspond- ing mode for the frequency shown below: MODE ADJUST COUNTER FREQUENCY LSB TCroos 823.400 kHz (£50 Hz) CW TCyoos 825.900 kHz (+10 Hz) USB VRzoos —_8216.600 kHz (£50 Hz) 1. BFO Frequency Set the transceiver to a CW mode, and connect the frequency counter to pin 2 of Qsoi2- Adjust TC2o01 while receiving for 15.000700 MHz (+10 Hz) on the counter. J. FM/AM Carrier Frequency 1, Set the transceiver to the FM mode, and connect the frequency counter to Joo. Adjust VRzo0s while transmitting for 8.215000 MHz (+50 Hz) on the counter. 2. Rotate the AM CAR control (VRz09s) fully clockwise, and set the transceiver to the AM mode. Close the PTT line and check the counter for 8.215000 MHz #300 Hz. K. Carrier Level Set the transceiver to the LSB mode, and connect the RF voltmeter to TPz991- Close the PTT line and adjust TC2o03 for 90 mVrms (#5 mV). L. Carrier Balance With the transceiver set to LSB, connect the RF voltmeter to Jaoo7 and adjust VRao9; for ‘minimum voltage on the meter. M. AM Carrier Level 1. With the RF voltmeter connected to Jyo07, set the mode to CW, key the transmitter, and note the voltage indicated on the meter (approx. 200 mVrms). 2, Return to receive, switch the mode to AM, close the PTT line and adjust AM CAR control VRzo9s for exactly half of the voltage noted in the previous step. {Chassis Top View: LOCAL Unit Adjustment Locations -15-N. 1 PLL Subloop (PLL-1) VCC Connect the hi-Z DC voltmeter to TPzgo3 and tune the transceiver for 14,499.00 on the display. Adjust Tao99 for 5.5 V on the meter. 2. Retune the transceiver for a display of 0. 1 14,500.00, and check for 2 to 3 volts on the meter, 41 and 56 MHz Bandpass Filters Connect the RF voltmeter to TPzooq and tune the transceiver for 14,250.00 on the display. Adjust Ty9;4 through Tzo17 for maximum deflection on the voltmeter (more than 60 mVrms). 2. Retune the transceiver to 21.250 MHz, and P. adjust Tzoig through T3o2, for maximum deflection on the voltmeter (more than 60 mVrms). Main PLL (PLL-2) VCC 1, Connect the hi-Z DC voltmeter to TP3o95 and tune the transceiver to the frequencies shown in the following chart, adjusting the cor- responding transformer for 1.5 V on the meter. Then retune the transceiver to the corresponding “check” frequency, and check for 5 to 6 V on the meter. ADJUSTMENT (for 1.5V) | CHECK (for 5-6V) Freq. (MHz) | Transforme:| Freq. (MHz) 0.500 Tags 7.499 7.500 Thora 14.499 14.500 Troas 21.499 21.500 Troe 29.999 2. Check for proper VCC control by tuning Qa between the adjustment and check frequencies in each of the above four ranges, using the tuning knob or microphone scanning buttons, and watching the DC voltmeter for smooth voltage change. If the voltage changes un- evenly, or jumps, a fault is indicated. 2nd Local Level Connect the RF voltmeter to Jzo09. Adjust T2003 through Tzo95 for maximum RF voltage on the jeter (at least 110 mVrms). R. IF Shift Zero Point Set Connect the frequency counter to Jzo99, and with the Shift and Width controls centered, note the counter frequency while receiving Then key the transmitter and adjust VRzo97, if necessary, so that the frequency shown on the counter is within 50 Hz of that shown while receiving, While receiving, check the total adjustment range of the Shift control in USB, LSB and CW, which should be approximately +1.3 kHz as shown on the counter. If not, adjust L2o11 (not more than 90° in either direction), and then repeat adjustments H, I and J (Carrier Point, BFO Frequency and FM/AM Carrier Frequency), and then this check again. S. VOX Gain Preset Preset VRaoi1 fully clockwise, and set the VOX GAIN control on the rear panel fully clockwise. Connect the AF signal generator to the PATCH jack, and apply a I kHz signal at 1 mV to check to see if the transmitter activates, Now rotate the VOX GAIN control fully counterclockwise, and slowly adjust VRao11 counterclockwise to the point where the transceiver returns to receive, and then a little further counterclockwise from this point. T. SSB Carrier Point Check 1 With the AF generator connected as in the previous step, set the transceiver to the 14 MHz band, USB mode. Close the PTT line and adjust the MIC gain control for 100 watts output (into the dummy load/wattmeter). For the 10-watt model FT-757SX, divide all power outputs by 10. Reduce the frequency of the audio generator while watching the wattmeter, to obtain 25 watts output. Check that the audio frequency is below 350 Hz Now increase the frequency of the AF generator so that the power output rises to full power and then down to 25 watts again above 2 kHz. Check that the audio frequency is now above 2900 Hz.4, Retum to receive, switch to LSB, and repeat the above checks in this mode, If 25 watts output is not obtained outside the specified frequency in any of these checks, repeat the Carrier Point (H) and then the IF Shift Zero Point (R) procedures. U. FM Modulation 1. With the test equipment connected as shown in the following diagram, preset VRzoo2 fully clockwise, and set the AF generator for 10 mV output at | kHz. Set the transceiver to FM. 2. Adjust VRao03 for +5 kHz deviation (+100 Hz), and then reduce the AF generator output level to 1.5 mV, and adjust VRaoo2 for 43.5 KHz deviation (£100 Hz). 3. Recheck deviation with 10 mV audio, and repeat the above steps until deviation is within the specified ranges for both audio levels. ‘Somoling Coupler ANT ar Linear Detector Generator (Deviation Meter Transceiver ar itive f= MIC meter -7- erminated| WattmaterRE Unit: Receiver Circuits A. 3rd Local Buffer Connect the RF voltmeter to the emitter of Qiozs and adjust T,9,9 for maximum RF voltage (0.7 to 0.9 Vrms). B. 2nd Local Buffer Connect the RF voltmeter to the jumper between Tyoos and Tyo23 on the component side of the board, and adjust T922 for maximum RF voltage (0.25 to 0.35 Vrms). C. Width Oscillator (Coarse) 1. Connect the frequency counter through a 0.01 uF capacitor to pin 1 of Qyoza. Set the WIDTH control to the 12 o'clock position, and adjust Lyogq for 8.670 MHz +100 Hz on the counter (coarse adjustment), 2. Connect the RF voltmeter to gate two of Quors and adjust Tyo19 for maximum RF voltage (0.5 to 0.6 Vrms). D, RX IF Transformers Preset VRioo, fully clockwise and adjust VRyo19 to the point where the S-meter just begins to deflect. Apply a 60 dB signal at 14,000 MHz from the RF signal generator to the antenna jack, and adjust Tore through Tyo, and Tyo7 through Troe, in that order, for maximum -meter deflec- tion. Reduce the signal generator level as necessary to keep the meter below full scale. E. Width Oscillator (Fine) With the WIDTH and SHIFT controls both set to the 12 o’clock position, switch the mode back and forth between LSB and USB, adjusting Lioag for the same noise pitch. F. IF Gain and S-Meter Sensitivity 1. Apply a 6 4B signal at 14.000 MHz from the RF signal generator to the antenna jack, and adjust VRjoo: for an S-meter deflection of SI 2. Increase the RF signal level to 100 dB and adjust VR,o11 so that the S-meter indicates just to full scale G. Noise Blanker Connect the DC voltmeter to gate two of Qioi3, and with the RF signal generator connected as above, set the RF level to 40 to 60 dB at 14.000 MHz. With the NB button depressed, adjust T1008 and Tyo95 for minimum DC voltage on the meter. H. FM 3rd Local With the RF signal generator connected to the antenna jack, apply a 40 to 60 GB signal at 14.000 MHz, modulated with a 1 kHz tone at £3. kHz deviation. Connect the AF voltmeter across the speaker terminals; set the SQL control fully counterclockwise, and adjust Tyo17 for-maximum AF voltage on the meter. I. Squelch Threshold Beginning with the transceiver in the AM mode, with no signal applied at the antenna jack, advance the SQL control gradually from the fully counter: clockwise position just to the point where the squelch closes, Then switch to the FM mode, and adjust VRjoo3 to the point where the squelch again just closes. J, FMRX AF Output Level 1. With the AF voltmeter connected across the speaker terminals, apply a 40 dB signal at 14.000 MHz (with no modulation) from the RF generator to the antenna jack. Set the transceiver to the USB mode, tune for a heterodyne, and adjust the AF gain control for 0.1 V on the AF voltmeter. 2. Switch to the FM mode and modulate the RF signal with | kHz at £3.5 kHz deviation, with- out changing the generator output level. Adjust VRio02 for 0.1 V on the AF voltmeter. 1B -F—VRioso Troe Taoor —Jumper(2nd Local check) Qrors soos Too Troe Qrove: Tors Those Throw: Chassis Bottom View: RF Unit RX Adjustment Locations geRF Unit: Transmitter Circuits A. ALC Meter Zero Set With the transceiver tuned to 14 MHz, USB mode, and with no microphone input, key the transmitter and adjust VRyoo3 to the threshold point where ALC just starts to produce meter deflection (METER switch in ALC position), B. TX IF Transformers At 14 MHz, CW mode, with the METER switch set to ALC, preset VRyoog to the center of its range. Press the MOX switch and adjust Tyo29, Tiozs and Trozs through Tyo25 for maximum deflection on the ALC meter. If no deflection is found at first, set the METER switch to PO and the rear panel FWD/REV switch to FWD. Return the METER switch to ALC when the PO indication is maxi- mum. If the ALC indication is overscale, reduce the setting of the DRIVE control. C. TX Power At 14 MHz, CW mode, set the DRIVE control fully clockwise and adjust VRyoos for 100 watts output (10 watts for FT-757SX). ve, D. PO Meter At 14 MHz, CW mode, press the MOX button and adjust the DRIVE control for 100 watts output on the external wattmeter. Set the rear panel FWD/ REV switch to FWD, and with the front panel METER switch set to PO, adjust the FWD SET control for internal PO meter indication of 100 watts, E. SWR Turndown (Automatic Final Protection) At 14 MHz, CW mode, connect 16.6-ohm dummy oad (three 50-ohm loads in parallel) and a thru-type wattmeter to the antenna jack. Rotate the DRIVE control fully clockwise, press the MOX button, and adjust VRyoo7 to the point where power indication on the wattmeter just begins to drop. F. CW Sidetone Level With the AF voltmeter connected across the speaker terminals, in a CW mode with a key connected, close the key and adjust VRioos for 0.3 V sidetone output on the meter. + (OW Sidetone Level) Chassis Bottom View: RF Unit ‘TX Adjustment Locations onLPF Unit: Directional CM Coupler Balance Set the METER switch to PO and the rear panel FWD-REV switch to REV. Set the transceiver to the CW mode, and transmit a 14 MHz carrier into the dummy load. Adjust TC399; for minimum deflection on the meter. Yseer TCsoe1 Javos LPF Unit Qs PA Unit: Idling Current Remove the jumper shown in the following figure, and connect the DC milliammeter (500 mA range) in place of the jumper. With the transceiver set to an SSB mode and with no audio applied to the transmitter, close the PTT line and adjust VReoo: for 250 mA (£100 mA) on the ammeter. Replace the jumper after the adjustment. For the FT-7578X, adjust VRyo91 for 150 mA (£50 mA). 1001 Quoos Quc0s Yu002 Yaooe soos KEYER UnitSEMICONDUCTOR LOCATIONS ainDISPLAY NT Inside Front Panel ~3-a a a a = < < a =z z 9 a — mHSIGNAL PATHS: CW 23 -WEOVIO WOOT] XS7O0SL-15 SIGNAL PATHS: AMPBSVTO SOOT) XS A@LSE=13 oct — fe ot 7 = iz Q z= = a = z 9 aMAIN CHASSIS LOCA- _NOMEN- TION CLATURE 1 uPC7e08H RF UNIT LOCA- NOMEN TION CLATURE 1001 2sc380TMY 1002 Mci4sisBcp 1003 2sK12s 1008 z Q1005-25a733 21006 28K125, qi07 Qos 1009 28A733AQ quo10 2ski073 aio 2 Q101238K73GR Qi013 Q101s -2sc380TMY Quis 1016 38K73GR qo Qi01s Q10192sc380TMY qu020 3 i021 2sK241GR 1022 Mc3359P 2sc3a0TMY 38K73GR 2scaa0TMY AN6552 cts066e 2sc380TMY Mag713 28c380TMY 28A733AQ asks 2519230 2sk1073 2sc380TMY 28A733A0 COMPONENT APPLICATIONS TYPE Regulator IC TPE, NPN SiTR Dual BCD Counter JEET PNP SiTR JET PNP Si TR JFET MosFET NPN SiTR MOSFET NPN SiTR JEET FMRXIC NPN SiTR MOSFET NPNSITR Dual Op amp ‘Quad Analog swiC NPNSiTR AP amp IC NPNSITR PNP SiTR JEET NPN SITR weet NPN SiTR PNP SiTR APPLICATION BV Reg for Local Unit APPLICATION Marker Buffer Amp 130 Divider Marker) RX RE Amplifier Relay Driver RX Ist Mixer RX Ist IF Post-Amp RX Front End Mute (on TX) RX Ind Mixer RX Nolee Amp RX NBAGC Amp RX NB Gate Sw RX 3rd Mixer RX 3rd IF Amp RX AGC Amp RX AGC Bulfer RX 2nd IF Butter M RX rd Mixer, Lim Amp, Discriminator, Noise ‘Amp, Squeleh Sw RX Squelch Sw RX IF Width LO RX Width Local Amp RX Local Butfer Amp RX Carrer Mixer RX Carrer Buffer RX REAGC Amp Auto Sean Diff Amp RX Detector Selector Switeh RX Detector Squelch Switch RX AM, SSB Active LPF RX PM AF Buffer RX CW Active LPF RX AF Preamp, TX Sidetone Ose RX AP Power Amp [TX SSB Drive Sw ‘TX Drive Enable Sw VS) TX Is IF Butter 2nd LO Butfer (BX and TX) TX Ind Mixer ‘TX 10m PO Reduction Sw (for JAS) — 28 1046 1047 104s, i089 1050 10st 1052 Q10s3 1054 ross 1056 1087 toss: 21059 1060 21061 1062 1063 Q1064 1065 1001, 1002 1003 i004 100s 1006 1007 1008 1009 1010 Diol i012 puoi Dioig Diois Dios Dio17 Dios Di019 1020 pioat Dio22 i023 i028 i025 1026 1027 1028 i029 1030 Diost 1032 1033, ANGS52 28C380T™MY 3SK73GR 2sK125 2N4a27 ANG552 28A73340 28K1073, Mci4066B 2sc3soTMy 2SAL193K aPC7808H BSA733AQ MCI4011BCP 28c330TMY 2873340 25C380TMY 2SAT33AQ Maiso Dus! Op amp NPN Si TR MOSFET JET NPNSiTR Dual Op amp PNP SiTR JET Quad Analog sw IC NPN SiTR PNP SITR Regulator IC PNP SiTR Quad NAND NPN SiTR PNP SiTR NPN Si TR PNP SITR Si Diode Schottky Barcier Diode ‘TX ALC Diff Amps TX ALC Butter TX nd IF Amp TX RF Post-amp ‘TX RF Preamp PO Meter Amps RX/TX S/ALC Meter ‘Amp Meter Function Selector Inverter for TXBV Sw 1056 ‘T/R Sw for TXBV on RF Unit ‘TR Sw for RXBV on RF Unit BV Reg for RF Unit PET Switch Burter ‘TR Switching Syne TX Sidetone Switeh (/01064) ‘TX CW Key Enable Sw TXIF T/R Sw TX Sidetone Ose Sw “BV Delay Suite Marker Output Sw Marker Divider Preset ‘Switch BPF to TX RF Preamp ‘Switch (FX BV) TX Switeh BPF Switch OS~25MH2) cal > ” @5~40MHa) Set mae (4.0~75MEe) “¢ ) " (1S~14.SMH2) ie ) " (4.5~21.5MHz) aie ) (@1.s~s0MHe) cn) BC BPF Enable Switch 1L.9MH BPF Enable ‘Switeh BCRF Amp Relay Sw Not Used 24.5/28ME BPF/LPF Diode OR @28MHz) (45M) 18/21MUtz BPE/LPF Diode OR (21MH2) " (SMiz) 10/14MEl: BPE/LPF Diode OR (14Mi2) * GOMHE) ‘Back Pulse Cancellri034 103s i036 1037 i038 1039 i080, i041 Dios i043 Dioss Dioss Dios Dios7 Dioss, Dios i030 Di0si ios ios piosa Dioss, Dios6 1087 ise Dios9 1060, i061 1062 1063, Dios i065: i066. 1067 Dioss. i069 i070 pio71 pio72 1073, pio7 iors pio76 piom? i078 i079 Diogo 1ssi06 MAI90 18897 Mai90 188106 1svs0 Mai90 ND#B7RISR, MAI90 Schottky ‘Barrier Diode Si Diode Sehottky ‘Barrier Diode Si Diode Sehottky Barter Diode Varactor Diode Si Diode ‘Ring Module Si Diode RX IStIF T/R Sw Go XFo1) TX 2nd IF T/R Sw (Gom XFO1) TX 2nd IF T/R Sw (0 XPO1) RX Let IF TIR Sw (from XFOL) NB Nowe Detector Reverse Voltage Isolator NB Gate RX 2nd IF T/R Sw (Go Xtal Filters) ‘TX StF T/R Sw (Grom Xtal Fatess) CW Xtal Filter Sw ‘S8B Xtal Filter Sw AM Attenuator Sw TX Ist T/R Sw (Go Xtal Filters) RX 2nd IF T/R Sw (Grom Xtal Fiters) RX 3rd IF AM Filter Swit RX 3rd IF $8B/CW Ceramio Filter Sw RX 3rd IF SSB/CW iter Selector (SSB) (ww) (cw) RX 3rd IF AM Filter Selector (AM) eM, OWN Xtal Filter Sw FM Demodulator ‘Activator Switch RX AGC Detector Forward Bias for AM Detector RX AM Detector RX FM Noise Detector IF Width Frequency Control BFO Premixer Enable Sw (SSB) CW BFO and AF iter Sw (CW¥) (cway, ‘BFO Premixer Enable Sw (cw) RX SSB, CW Demodulator Reverse Voltage Protector (SCAN Line) RX SSB/AM AF Filter Sw ($SB) aM RX SSB/AM AF Fier Switch RX FM AF Buffer Sw — 29 Dios Dios2 E i083 v2 Varistor 1084 RDIIEB2 Zener Diode 1085 MAI90 Si Diode D108 RDP.AEB2 Zener Diode i087 MAI90, Si Diode D108 RDV.1EB2 Zener Diode 1089 MA190 Si Diode 1090 ND487C2-3R Ring Module i091 MA190 Si Diode 1092 a 1093, a i094 Dio9s a 1096 = - i097 MA190 Si Diode 1098 5 7 i099 viz Vatistor Diode 1100 MA190 Si Diode puoi 7 G pi1o2 c 5 Dit03 a 2 Dito4 HzAB3 Dinos A190 pisos Hz3c1 D107 MA190 pues pig a XFI001 XF-47M-203-01 Crystal Filter XF1002 8.220 " XF1003_XF8.2M601-01 XFI004_XF8.2M-27201 clooL Lees Ceramic Filter CFL002 CI44SKI3, “ C1003. CEGASSEL X1001 HCI8/U Crystal 670K LOCAL UNIT LOCA- NOMEN; TION cLaTURE TYPE 2001 2C8S8BNPNSITR 92002 B 92003 02008 SNI6913P Mixer Ic 2005 25C458BNPNSITR e006 5 e 2007 a 22008, . RX CW AF Filter Sw Not Used ‘Temperature Comp for ALC Rev ALC Latchup Protector Reverse EXT ALC Protector Fwd/Rey ALC Diode OR (Rev) Fed ALC Latchup Protector Frid/Rey ALC Diode OR wd) 1X 31d Mixer Reverse Voltage lolator (Grom Meter Amp 10518) rom 210608) PTT Line Switch CW Keying Line Sw Not Used SMH TX Disabie 24 5MHz TX Disable ‘ALC Preset Fa Bias ‘SSB Xtal Filter Sw cava “_gsB) [AM Squstch Switch RF AGC Threshold Set Non-FM Squeich Hang ‘Timer NB AGC Limiter TX RF OUT Switch Demodulator FM Disable Switeh (Grom TX 8V) RX Ist IF Filter eee RX 3rd IF Filter (AM) "GSB,CW) c mn IF Width Oscillator [APPLICATION TX MIC Amp ‘TX AF Amp ($SB/AM) ‘TX SSB Balanced Modulator (also AM Mod) ‘TX Ist IF Buffer Amp ‘TX SSB PROC AF Limiter Amp TX FM IDC TX FM AF Amp22009 2010 201 2012 2013, 014 2015, 2016 2017 2018, 2019 22020 2021 02022 92023, 22024 02025 92026 92027 2028 92029 02030 2031 2032 02033, 2034 2035 02036 (Q2037 02038, 22039 2040 2041 2082 22083, 2044 nas 2086, 2047 2048 2049 ‘@2050 2051 22052 22053, on0s4 285358 SNIG913P 254588 23358 ascasan SN76514N 2805358 2scasas APCTBLOS 2SATI3AP 2sc4sB D10551P 285358 SN169138 28C535B Mctasias 28K192AGR 2504588 HDLOsS1P 28¢535B SNT6SI4N 285358 SN76514N 285358 MCissi45 2SATI3AP 2scasen 2scs3sB 2SATS3AP 28K192AGR 2scs3sp Mixer IC NPN SiTR Mixer IC NPN Si TR Regulator IC PNP SiTR NPNSiTR Divider IC NPN STR Mixer IC NPN SUTR ‘cmos IC JFET NPNSiTR Divider Ic NPN SiTR Mixer 1c NPN SiTR Mixer IC NON SITR cmos ic PNP SITR NPNSITR PNP SiTR weer NPN Si TR 13M VCXO. (1x FMICW) FM/CW TX Cartier Disable Sw RX and SSB/AM TX, 1SMHz Car LO Butler Carrier Premier RX Carrier LO Butter ‘TX Carrier LO Butter 6-78MHe SSB Car and SHIFT VCXO 32.06Ma 2nd LO and ‘WIDTH Vexo 32.06MHe Bulfer Amp 2nd Local remixer 2nd Local Buller Amp Disable Sw (CW) RX and SSB/AM TX, carer ey) Reg for RX IF Shift Preset on TX, Not Used IF Shit Disable on TX SMH PLL Ref, RX and SSB/AM TX Car Oselator SMH: Burtor Amp 1/20 Ret Divider for Marker 49M Tripler for PLLL LO’ PLLI Mixer PLLLIF Amp PLL Prog Div and Phase Detector 34-39MHe VCO PLL) PLLI VCO Feedback uler PLLI VCO Output Balter 1/20 PLLA Output Divider PLL Ref Triple Quadrup PLL? Local Premixer PLL2 SIMtis Local amp PLL2 S6MHe Local Amp PLL? Mixer PLL2IF Amp PLL2 Prog Divand Phase Detector PLL Unlock Switch ‘TX Inbibie Switch (for Ustock) PLL2 Ist RX, 3d TX ‘Local VCO (S~75MH2) (75~14.SMi) (14.5~21 5Mui2) " @13~30.0Mi) PLL? LO ana VCO Bandewitch (05~75Mt) " (5=14 SMH) “ (4s~21 Miz) ” @15~30MHz) PLL2 VCO Feedback Buller Amp 205s q20s6 2057 2058, Q2059 22060 2061 22082 22063, ‘22064 22065 2066 (92067 22068, 2069 2070 ont 2072 qu073 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 D201 2012 2013, 201g 201s 2016 2017 2018 2019, 2020 2021 2022 2023, 2024 202s Sn 285358 2ne427 254588 ANGSS1 25458 ctsozsacr MCLaS1OBCP McIs0L1BCP sca2o72F PC78LOS Mc1s042BCP SN7SLS14SN 24588 1270 Maigo wvi03 Mai90 FCS3M5 MAI90 RD7SEBS MAi90 Fess 1svs0 MAi90 1ss101 RD9.1EB3 NPNSITR Op amp IC NPN SiTR BCD-Dee Decoder IC BeD UD Counter IC (Quad NANDIC Sit uP LSE Regulator IC Quad Lateh IC BCD-Dee Decoder IC NPN Si TR Ge Diode Si Diode Varistor Diode Si Diode Varactor Diode Si Diode Zener Diode Si Diode ‘Varactor Diode SiDiode Schottky ‘Barrir Diode Zener Diode PLL2 VCO Output Baier Amp Not Used. Ist RX/3rd TX LO Preamp Ist Local Amp VOX Amplifier VOX Comparator VOX Switch Counter Startup Delay ‘Switeh P PLL Div Freq Dats Decoder Tuning Pulse Counter ‘Tuning, Auto Sean Gates Freq Control CPU SV Reg for Local and Dial Unit Logic P Band Data Decoder Latch Band Data BCD-Dec Decoder (CPU Startup Reset Delay Suiteh| TX Inhibit Switch fot MAN and EXT) ‘TX, SSB PROC Limiter ‘TX FM IDC Switeh TX AF Amp Disble Switeh (CW) TX AF Amp Disable ‘Switch (FM) ‘Temp Compensator for FM Modulator TX CW Car Ose Crystal ‘Switch ‘TX FM Car Oxe Crystal Suiteh FM Modulator ‘TX FM Car Ose Bias Sw ‘TX FM/CW Car Ose Disable Sw (RX) RX, SSB/AM TX 1SMHz Car LO Disable (FMCW TX) Enable Sw(") Rev Voltage Islator (SSB/CW RX) SV Reg for Car Sw out [USB Car LO Xtal Sw for USB, CW, AM, FM LSB Cat LO Xtal Sw 6.18MHz VCXO IF ‘SHIFT Contr 32.06MHz 2nd LO IF WIDTH Control Rev Voltage Itolator (CwTX sw) "EMIX Sw) (SHIFT TX Preset) aoe ) Reg for SHIFT Reference2026 2027 2028 2029 2030 2031 2032 2033, 2034 2035 2036 2037 2038 2039 2040 20st 2042 2043, 2044 204s, 2086, 2087 2048 2049 2050 D20s1 D20s2 2053 2nsa p2oss: 206 2057 2058 2059 2060 2061 2062 2063, 206s 206s: 2066 12067 2068 2069 2070 2071 2072, 2073, Mai90 issios sissa RDS.LEB2 FesaMs RDS.1EB2 Mais0 1sv103, Mago Si Diode Schottky Barter Diode Si Dioge Zener Diode Varactor Diode Zener Diode SiDiode Varactor Diode Si Diode Rev Voltage Isolator (SHIFT TX Preset) * (AM Car Preset) (Carrer Premix Vee OR (on LSB) " (on USB) * oncw) Bal Mod Car Bias OR (encw) (on FM) USB Car VCXO Sw OR (oncw) " (on aM, (on FM) SSB/AM TX AF Amp Vee OR (on LSB) (on USB) (on aM) USB Car VCXO Sw OR (on USB) INH Reverse Voltage luolator Back Pulse Canceller Vee Reg for Marker Divider 34-39MH Veo eu) Vee Rep for PLL Output Divider PLL Ref Triple n Sw PLL Ref Quadruple Input Switeh 44SMElz PLL Ref Triple Ousput Switch OME: PLL Ret Quadruple Out Sw 41MHiz PLL? LO BEE Input Switch SMH PLL? LO BPF Input Switch 41M PLL2 LO BPE Output Switch ‘S6MHlz PLL2 LO BPF Output Switch PLL2 VCO A Control (05~75MH2) ” BConteot (7s~14sMti) Contr (14.521 si) a D Controt (@15~30.0MHi2) ‘A Out Sw aa ce ne PLL2 41MHe BPF OR (with VCO A on) i Bon) PLL2 S6MHe BPF OR (with VCO C on) "Co" Den) Dee Band Dat-to-VOO ‘A Decoder OR Dec Band Dateto-VCO ‘A Decoder OR conse -3 2074 2075, 2076, 2077 2078 2079 2080 208i 2082 2083 208s ross 2086 2087 2088 2089 2090 2091 2092 2093 2094 209s 2096 p2097 2098, 2099) 2100 x2001 x2002 2003 x2004 x2005 2006 1N270 Ge Diode Mat90 Si Diode RD6.2EB3—_Zener Diode MAI90 Si Diode 18897 Schottky ‘Barrier Diode MaI90 Si Diode RD9.IEB3 Zener Diode Malg0 Si Diode RDS.2EB3 Zener Diode Mais0 Si Diode 1s.0007MiR —HC-AR/U Crystal 15.0000 ; 6.7834MHs z 6.7865MHz 5 32.060MHz = HO43/U Crystal 15.000MH 5 LPF UNIT Loca- TION 3001, 3002, 3003, 13008 300s 3006: 3007 3008 3009 p3o10. NOMEN. ctature TYPE Isis5s SiDiode on VOX Rectiier ANTI TRIP Rectifier Sidetone Enable, ATRIP Disable Svitch Delay (Q2061) Rev Voltage lolator VOX Camp Sidetone Delay Enable ‘Switch INH Line Rey Voltage Protector (for Q2068) Backup Battery Protector SV Veo Rev Voltage Protector ‘Sean Glock Diode OR ‘Scan Pulse Diode OR PTT Jack Rev Voltage Protection for Q2068 Delayed PTT Diode OR to CPU TX 13 5V Sw Signal Diode OR to CPU Counter Startup ‘Threshold Set ‘Shift Disable (2024) ‘Swetch Bias (CPU Qock Reset Sw PLLI Unlock Diode oR PLL2 Unlock Diode OR (CPU Startup Reset ‘Threshold Set INH Sw Forward Biss FM Shift Diode OR aM (OW BFO Cartier Oseilator FM Cartier Oxcilator USB Carter Oscillator LSB Carrier Osilator 2nd LO and WIDTH VCXO) PLL Ref and AM Car Oscillator APPLICATION ‘Back Pulse Canceler Rev ALCISWR Detector Fwd ALC/SWR Detector Rev ALC/SWR Detector Fwd ALC/SWR Detector301 3012, 013 Isisss DISPLAY UNIT Loca: TION 4001 4002 94003, 4901 4002 4003, soos soos 4006 8007 e008: 4009 péo10 Dal 4012 4013 bios D4ois, Danis soi? Davis 4019 pso20 Déo2t 4022 péo23 sors psoas NOMEN: CLATURE 2sca96y 1Ms2370 2SAT33AQ Isisss 1ssss Hzscl RD3OEB2 1stsss 72483 Isisss LNatoyP 151355 COt001 CSBSOOE DIAL UNIT LOCA- NOMEN: TION CLATURE 95001 Mci401iBcP (95002 MC14s84ncP 95003. Mci4071 BCP 95004 MCI4071 BCP 05008. -MC140138CP s001 181555 Dsoo2 5003 Si Diode Tyre NPN Si TR bin CPU PNP SITR Si Diode Zener Diode SiDiode Zener Diode Si Diode LED Si Diode Ceramic Resonator TPE (Quad NAND IC Hex Schmitt Trig IC Quad oR Ic Dual 4 AND IC Dual “D" FF Si Diode RE Pickup Rectifier RF Pickup Detector Bias Back Pulse Canceller APPLICATION DC-DC Converter Oscilator Display Contzol CPU CPU Reset Switch Display “CH” Diode OR (109) * (gsee) ~30V Rectifier ~25V Bias ~30V Regulator BV Rectifier AV Regulator CLAR, M-VFO, VOM, PB2 Sw VEO=M Sw INH Suiteh UP Switch DWN Suites CLAR Switch D LOCK Switen VFO A/B Switch M=VFO Switeh SPLIT Switch MR Switeh VFOOM Switch (ON AIR Indicator D LOCK, VFO A/B, M-VFO amp VEOZM, INH Camp UP, DWN, CLAR Camp SPLIT, MR, VFO--M ‘Camp INT Camp ‘S00K2 Display CPU ‘Clock Oseillator APPLICATION Beeper Multivibrator Pulse Shapers, Up/Down Logie Up/Down Logic, Buzzer Switeh| Tune Disible 6 Burzer Diode OR Tune Disable by D LOCK Diode OR Buzzes Timer 100W PA UNIT LOcA- NOMEN. TION CLATURE 6001 2sc1974 6002 28c2395 6003 Q6008 2802879 soos 6008 uPC7808H 26007 2sD880.0 (96008. 2a1012¥ Qs009 28C45aD 6010 28D592R 6011 TL770s Q6012 2sa9s21, 6013. MCI401 BCP soo! Hz3C1 600210010 s003 5004 Devos D600 1sisss s007 5008 Dso09 D6010 Deo 5012 2 10W PA, Loca- NOMEN. TION CLATURE 7001 28c2166 7002 252509 7003 97004 uPCTSLOS 7005 2sD882Q 7006 _2sc4s8D Q7007 | 2Sa1012¥ Q7008 | MCI4011BcP 7009 2sD892R D701 Hz3c1 Dmo2 MVII 7003 sisss Dro 7005 7006 1007 7008 7009 TPE NPN SiTR Regulator IC NPNSiTR PNP SiTR NPN Si TR OP Amp 1c PNP SiTR (Quad NAND Ic Zener Diode Si Diode TYPE NPN SiTR Regulator IC NPN SiTR PNP Si TR (Quad NANDIC NPNSUTR Zener Diode Varistor Diode Si Diode APPLICATION TX Preariver TX Driver ‘TX Final Amplifier Final Bias Reg TX 13.5V Sw TK 13 SV Sw Dever Power ON Relay Diver Fan Switching Comparator Fan Driver ‘TXIRX Sw and Delay (for TX 13.89) Predviver Bias Regulator Temp Compeasitor (or Driver Bias) ‘Temp Compensitor (for Final Amp Bias) PIT T/R Delay Trigger PTT Delay Gate OR Reverse Voltage Ttolator PIT 13.5V Diode OR PWR Relay Back Pulte Cenceller RX Mute Diode OR PWR ON Rev Voltage iolator APPLICATION 1X Driver ‘TX Final Amplifier Final Bias Regulator ‘TX 13 SV Sw Dever TX 3.5V Switeh ‘TX/RX Sw and Delay (or TX 13.5V) Relay Driver Driver Bias Regulator Temp Compensator (Gor Final Biss) PTT T/R Delay Trigger PTT Delay Gate OR PIT 13 SV Diode OR Reverse Voltage Itolator PWR Relay Back Pulse Canceller RX Mute Diode OR PWR ON Rev Voltage Isolator