ECE 621

Signaling & Synchronization

Fall 2017

Topic 1
Introduction

Sameh A. Ibrahim
Ain Shams University
ICL
(Courtesy of S. Pamarti, UCLA)
 Course Administration
 Instructor: Dr. Sameh A. Ibrahim IC Lab, Third floor, Room 311

 Office Hours: Sat. 11:00 AM – 1:00 PM

 e-mail address: [email protected]

 Website:
Facebook Group

 Time & Place: Tue. 6:00 – 8:00 PM (Weekly), Rm. 316

 Reference Material:
▪ Lecture Notes
▪ Selected Papers
 Grading:
▪ Design Project (Through Assignments) 50%
▪ Final 50%

Introduction
2
 Course Topics (1)

 Introduction to Signaling and Synchronization

 I/O Channel Characteristics
▪ Frequency-Dependent Loss – ISI
▪ Reflections
▪ Cross-Talk
 TX Building Blocks
▪ Voltage/Current Mode signaling
▪ Line Drivers
▪ Pre-Emphasis
▪ Multiplexers

Introduction
3
 Course Topics (2)
 RX Building Blocks
▪ Equalization techniques and architectures
▪ FFE and DFE circuits
▪ Slicers
▪ Demultiplexers
 Clock and Data Recovery (CDR)
▪ PLL and DLL Basics
▪ Jitter Concepts: generation, transfer and tolerance
▪ Phase Detectors
▪ Charge Pumps
▪ Voltage-Controlled Oscillators (VCO)
▪ Frequency Dividers
 Advanced Signaling Techniques
Introduction
4
 The Road to SOCs
 A typical system-on-chip SOC consists of:
▪ A microcontroller, microprocessor or DSP
core(s)
• Taught in a digital design course.
▪ Memory blocks including a selection of ROM,
RAM, EEPROM and flash memory
• Taught in a digital design course.
▪ Timing sources including oscillators and
phase-locked loops.
• Taught in an analog system design course
• Taught in a serial-link design course.
▪ External interfaces including industry standards such as USB, FireWire,
Ethernet, USART, SPI
• Taught in a serial-links design course.
▪ Analog interfaces including ADCs and DACs
• Taught in an analog system design course.
▪ Voltage regulators and power management circuits
• Taught in a power management course.
Introduction
5
 Core i7 Kaby Lake Architecture

 7th Generation Core Processor Released August 2016 (phase 1/Mobile) and
January 2017 (Phase 2/Desktop) using 14nm Tri-Gate 3D transistors. (14nm+)
 In August 2017 Intel announced a Kaby Lake Refresh marketed as the 8th
generation mobile CPUs. Introduction
6
 Signal Integrity

CPU-GPU

 Signal Integrity refers to all the problems that arise in

high-speed products due to the interconnects.
 Problems fall into one of three categories
▪ Timing
▪ Noise
▪ Electromagnetic Interference (EMI)
Introduction
7
 How Important is SI?
 Pre-1990
▪ 10 MHz Clock, 10 nsec rise and fall times
▪ SI addressed only after failure
 1990-2000
▪ >100 MHz Clock, < 1nsec rise and fall times
▪ SI focused on channel models
▪ SI integrated in high-speed digital system design
 2000-Present
▪ GHz range Clock
▪ Rise and fall times in psec
▪ SI drives architecture choice.
▪ SI models the entire link.
Introduction
8
 Why Now?

 From parallel to serial to multiple-channel serial

 Data rates beyond 10 Gb/s
 Lower voltage swings
 Get it right or it does not work

Introduction
9
 Serial Link Standards – Desktop
• PCIe (PCI Express)
• Computer expansion bus
• 2.5, 5, 8, 16 Gbps
• USB
• Universal Serial Bus
• For computer peripherals
• 0.012, 0.48, 5, 10 Gbps
• SATA
• Mass storage devices
• 1.5, 3, 6, 16 Gbps

• HDMI • DMI
• Audio/Video interface • Connects controllers
• 5, 10, 18 Gbps • 10, 20 Gbps
• Ethernet
• LAN 0.01, 0.1, 1, 10 , 100 Gbps • SPI
• DDR • Short distance, single master
• Memory 0.2, 1.066, 2.133, 3.2 Gbps
Introduction
10
Serial Link Standards – Mobile

• MIPI
• Low power
• Mobile applications
• 1.5, 3, 6, 12 Gbps

Introduction
11
 System Block Diagram

Data Path (Signaling)

D Q
Multiplexer

Pre-
Driver VGA RX EQ D Q
Driver
Clk
D Q Channel Clk Clk

Clk D Q
Clk
Clk
Clock Clock Path CDR Clk
Generation (Synchronization) Clk

Transmitter Receiver

Introduction
12
Topic 2: Channel Characteristics

Main-Cursor Frequency-Dependent Loss

Post-Cursors

Reflections

Pre-Cursor
Cross-Talk
Introduction
13
 Topic 3: TX Circuitry (1)

D Q

Multiplexer
Pre-
Driver
Driver
Clk
D Q

Clk
Clk

 Multiplexing
▪ Circuit design
▪ Clock distribution issues
▪ Power consumption issues

Introduction
14
 Topic 3: TX Circuitry (2)

D Q

Multiplexer
Pre-
Driver
Driver
Clk
D Q

Clk
Clk

 Driver and Pre-Driver

▪ Voltage and current mode drivers
▪ Bandwidth issues
▪ Swing control
▪ Impedance control

Introduction
15
 Topic 3: TX Circuitry (3)

D Q

Multiplexer
Pre-
Driver
Driver
Clk
D Q

Clk
Clk

 Termination Resistors
▪ On-chip or off-chip
▪ PVT variations

Introduction
16
 Topic 3: TX Circuitry (4)

Pre-
Driver
Driver

Pre-
D Q Driver
Driver

Clk
 Pre-Emphasis
▪ Power consumption concerns
▪ Coefficient choice
▪ Pre-emphasis vs. de-emphasis

Introduction
17
 Topic 4: RX Circuitry (1)

VGA RX EQ D Q

Clk Clk
D Q

 Input Termination Clk

▪ On-chip or off-chip
▪ PVT variations

Introduction
18
 Topic 4: RX Circuitry (2)

VGA RX EQ D Q

Clk Clk
D Q

 Variable Gain Amplifier Clk

▪ Large bandwidth required

▪ Offset and noise limitations
▪ Gain profile

Introduction
19
 Topic 4: RX Circuitry (3)

VGA RX EQ D Q

Clk Clk
D Q

 Receiver Equalization Clk

▪ Linear vs. DFE

▪ TX vs. RX equalization
▪ Analog vs. Digital

Introduction
20
 Topic 4: RX Circuitry (4)

VGA RX EQ D Q

Clk Clk
D Q

 Slicer Clk

▪ Offset and noise considerations

▪ High speed requirements
▪ Sensitivity

Introduction
21
 Topic 4: RX Circuitry (5)

VGA RX EQ D Q

Clk Clk
D Q

 De-multiplexing Clk

▪ Clock distribution
▪ Power distribution

Introduction
22
Topic 5: Clock and Data Recovery (CDR)

Phase Detector
Ref/Data Loop VCO/
PFD CP
Filter VDL

Divider

 PLLs and DLLs are used for clock generation and CDR
 PLL and DLL basics
 PLL and DLL Components
 Jitter and Noise analysis
 Linear and Non-linear clock recover systems

Introduction
23
Topic 6: Advanced Signaling Techniques
 Signaling techniques for better channel utilization
▪ 4-PAM signaling
▪ Simultaneous bi-directional signaling
▪ Mutli-tone signaling
▪ Duo-binary signaling

Introduction
24