Asus Zenbook Ux431fl Manual

E14902
First Edition / December 2018
E-Manual
COPYRIGHT INFORMATION
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by
any means, except documentation kept by the purchaser for backup purposes, without the express
written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES
OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION
OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL
USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE
CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY
ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND
SOFTWARE DESCRIBED IN IT.
Copyright © 2018 ASUSTeK COMPUTER INC. All Rights Reserved.
LIMITATION OF LIABILITY
Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to
recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to
claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death)
and damage to real property and tangible personal property; or any other actual and direct damages
resulted from omission or failure of performing legal duties under this Warranty Statement, up to the
listed contract price of each product.
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or
infringement under this Warranty Statement.
This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers,
and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS
AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL,
INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING
LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR
POSSIBILITY.
SERVICE AND SUPPORT
Visit our multi-language website at https://www.asus.com/support/
2 Notebook PC E-Manual
Table of Contents
About this manual......................................................................................................7
Conventions used in this manual.............................................................................. 8
Icons..................................................................................................................................... 8
Typography........................................................................................................................ 8
Safety precautions......................................................................................................9
Using your Notebook PC............................................................................................... 9
Caring for your Notebook PC...................................................................................... 10
Proper disposal................................................................................................................. 11
Chapter 1: Hardware Setup

Getting to know your Notebook PC....................................................................14
Top View.............................................................................................................................. 14
Bottom................................................................................................................................. 18
Right Side........................................................................................................................... 20
Left Side.............................................................................................................................. 21
Chapter 2: Using your Notebook PC

Getting started............................................................................................................26
Charge your Notebook PC............................................................................................ 26
Lift to open the display panel..................................................................................... 28
Press the power button................................................................................................. 28
Using the touchpad...................................................................................................29
Using the keyboard....................................................................................................36
HotKeys............................................................................................................................... 36
Function keys.................................................................................................................... 37
Notebook PC E-Manual 3
Chapter 3: Working with Windows® 10
Starting for the first time..........................................................................................40
Start menu....................................................................................................................41
Windows® apps...........................................................................................................43
Working with Windows® apps.................................................................................... 44
Customizing Windows® apps...................................................................................... 44
Task view........................................................................................................................47
Snap feature.................................................................................................................48
Snap hotspots................................................................................................................... 48
Action Center...............................................................................................................50
Other keyboard shortcuts.......................................................................................51
Connecting to wireless networks.........................................................................53
Wi-Fi...................................................................................................................................... 53
Bluetooth............................................................................................................................ 54
Airplane mode.................................................................................................................. 55
Turning your Notebook PC off...............................................................................56
Putting your Notebook PC to sleep.....................................................................57
Chapter 4: Power-On Self-Test (POST)

The Power-On Self-Test (POST)..............................................................................60
Using POST to access BIOS and Troubleshoot...................................................... 60
BIOS.................................................................................................................................60
Accessing BIOS................................................................................................................. 60
BIOS Settings..................................................................................................................... 61
Recovering your system...........................................................................................68
Performing a recovery option..................................................................................... 69
Tips and FAQs
Useful tips for your Notebook PC.........................................................................72
Hardware FAQs............................................................................................................73
Software FAQs..............................................................................................................76
Appendices
Internal Modem Compliancy...................................................................................... 80
Overview............................................................................................................................. 80
Network Compatibility Declaration.......................................................................... 81
Non-Voice Equipment.................................................................................................... 81
Federal Communications Commission Interference Statement.................... 83
FCC Radio Frequency (RF) Exposure Caution Statement.................................. 84
Wireless Operation Channel for Different Domains............................................ 85
Radio Frequency (RF) Exposure Information......................................................... 85
Informations concernant l’exposition aux fréquences radio (RF).................. 85
Compliance Statement of Innovation, Science and
Economic Development Canada (ISED).................................................................. 86
Déclaration de conformité de Innovation, Sciences et
Développement économique Canada (ISED)....................................................... 86
Caution................................................................................................................................ 87
Avertissement................................................................................................................... 87
UL Safety Notices............................................................................................................. 88
Power Safety Requirement........................................................................................... 89
TV Notices.......................................................................................................................... 89
REACH.................................................................................................................................. 89
Macrovision Corporation Product Notice............................................................... 89
Prevention of Hearing Loss.......................................................................................... 89
Nordic Lithium Cautions (for lithium-ion batteries)............................................ 90
CTR 21 Approval (for Notebook PC with built-in Modem)............................... 91
ENERGY STAR complied product............................................................................... 93
Global Environmental Regulation Compliance and Declaration................... 93
ASUS Recycling/Takeback Services........................................................................... 94
Rechargeable Battery Recycling Service in North America............................. 94
Coating Notice.................................................................................................................. 94
Regional notice for California...................................................................................... 94
Regional notice for Singapore.................................................................................... 95
Regional notice for India............................................................................................... 95
Notices for removable batteries................................................................................. 95
Avis concernant les batteries remplaçables.......................................................... 95
Simplified EU Declaration of Conformity................................................................ 96
About this manual
This manual provides information about the hardware and software
features of your Notebook PC, organized through the following
chapters:
Chapter 1: Hardware Setup

This chapter details the hardware components of your Notebook
PC.
Chapter 2: Using your Notebook PC

This chapter shows you how to use the different parts of your
Notebook PC.
Chapter 3: Working with Windows® 10

This chapter provides an overview of using Windows® 10 in your
Notebook PC.
Chapter 4: Power-On Self-Test (POST)

This chapter shows you how to use POST to change the settings
of your Notebook PC.
Tips and FAQs

This section presents some recommended tips, hardware FAQs,
and software FAQs you can refer to for maintaining and fixing
common issues with your Notebook PC.
Appendices
This section includes notices and safety statements for your
Notebook PC.
Conventions used in this manual
To highlight key information in this manual, some text are presented as
follows:
IMPORTANT! This message contains vital information that must be

followed to complete a task.
NOTE: This message contains additional information and tips that can
help complete tasks.
WARNING! This message contains important information that must be

followed to keep you safe while performing tasks and prevent damage to
your Notebook PC's data and components.
Icons
The icons below indicate the devices you can use for completing a
series of tasks or procedures on your Notebook PC.
= Use the touchpad.
= Use the keyboard.
Typography
Bold = This indicates a menu or an item that must be selected.
Italic = This indicates sections that you can refer to in this manual.
Safety precautions
Using your Notebook PC
This Notebook PC should only be used in
environments with ambient temperatures between
5°C (41°F) and 35°C (95°F).
Refer to the rating label on the bottom of your

Notebook PC and ensure that your power adapter
complies with this rating.
Do not leave your Notebook PC on your lap or near

any part of your body to prevent discomfort or
injury from heat exposure.
Do not use damaged power cords, accessories, and

other peripherals with your Notebook PC.
While powered on, ensure that you do not carry or

cover your Notebook PC with any materials that can
reduce air circulation.
Do not place your Notebook PC on uneven or
unstable work surfaces.
You can send your Notebook PC through x-ray

machines (used on items placed on conveyor belts),
but do not expose them to magnetic detectors and
wands.
Contact your airline provider to learn about related
in-flight services that can be used and restrictions
that must be followed when using your Notebook
PC in-flight.
Caring for your Notebook PC
Disconnect the AC power and remove the battery

pack (if applicable) before cleaning your Notebook
PC. Use a clean cellulose sponge or chamois cloth
dampened with a solution of nonabrasive detergent
and a few drops of warm water. Remove any extra
moisture from your Notebook PC using a dry cloth.
Do not use strong solvents such as thinners,

benzene, or other chemicals on or near your
Notebook PC.
Do not place objects on top of your Notebook PC.
Do not expose your Notebook PC to strong

magnetic or electrical fields.
Do not use or expose your Notebook PC near

liquids, rain, or moisture.
Do not expose your Notebook PC to dusty

environments.
Do not use your Notebook PC near gas leaks.
Proper disposal
Do not throw your Notebook PC in municipal waste.

This product has been designed to enable proper
reuse of parts and recycling. The symbol of the
crossed out wheeled bin indicates that the product
(electrical, electronic equipment and mercury-
containing button cell battery) should not be
placed in municipal waste. Check local regulations
for disposal of electronic products.
Do not throw the battery in municipal waste. The

symbol of the crossed out wheeled bin indicates
that the battery should not be placed in municipal
waste.
Chapter 1:
Hardware Setup
Getting to know your Notebook PC
Top View
NOTE: The keyboard's layout may vary per region or country. The
Notebook view may also vary in appearance depending on the Notebook
PC model.
Array microphones
The array microphones feature echo canceling, noise
suppression, and beam forming functions for better voice
recognition and audio recording.
Camera
The built-in camera allows you to take pictures or record videos
using your Notebook PC.
Camera indicator
The camera indicator lights up when the built-in camera is in
use.
Display panel
This high-definition display panel provides excellent viewing
features for photos, videos, and other multimedia files on your
Notebook PC.
Audio speakers
The built-in audio speakers allow you to hear audio straight from
your Notebook PC. Audio features are software-controlled.
Keyboard
The keyboard provides full-sized QWERTY keys with a
comfortable travel depth for typing. It also enables you to use
the function keys, allows quick access to Windows®, and controls
other multimedia functions.
NOTE: The keyboard layout differs by model or territory.
Capital lock indicator

This indicator lights up when the capital lock function is
activated. Using capital lock allows you to type capitalized letters
(such as A, B, C) using your Notebook PC’s keyboard.
Function key lock indicator

This indicator lights up when the function keys feature is
activated.
NOTE: For more details, refer to the Using the keyboard section in
this manual.
Touchpad
The touchpad allows the use of multi-gestures to navigate
onscreen, providing an intuitive user experience. It also simulates
the functions of a regular mouse.
NOTE: For more details, refer to the Using the touchpad section in
this manual.
Power button
Press the power button to turn your Notebook PC on or off. You
can also use the power button to put your Notebook PC to sleep
or hibernate mode and wake it up from sleep or hibernate mode.
In the event that your Notebook PC becomes unresponsive,
press and hold the power button for at least four (4) seconds
until your Notebook PC shuts down.
Power indicator
The power indicator lights up when the Notebook PC is turned
on and blinks slowly when the Notebook PC is in sleep mode.
Fingerprint sensor (on selected models)

This built-in fingerprint sensor captures your fingerprint and uses
it as biometric authentication for logging on to your Notebook
PC’s system.
Bottom
NOTE: The bottom side may vary in appearance depending on model.
WARNING! The bottom of the Notebook PC can get warm to hot while in
use or while charging the battery pack. When working on your Notebook
PC, do not place it on surfaces that can block the vents.
IMPORTANT!
• Battery time varies by usage and by the specifications for this

Notebook PC. The battery pack cannot be disassembled.
• Purchase components from authorized retailers to ensure maximum

compatibility and reliability. Consult an ASUS service center or
authorized retailers for product service or assistance on proper
disassembly or assembly of the product.
Air vents
The air vents allow cool air to enter and warm air to exit the
Notebook PC.
WARNING! Ensure that paper, books, clothing, cables, or other

objects do not block any of the air vents or else overheating may
occur.
Audio speakers
The built-in audio speakers allow you to hear audio straight from
your Notebook PC. Audio features are software-controlled.
Right Side
Memory card reader

This built-in memory card reader supports SD card formats.
Headphone/Headset/Microphone jack
This port allows you to connect amplified speakers or
headphones. You can also use this port to connect your headset
or an external microphone.
USB 2.0 port

The USB (Universal Serial Bus) port is compatible with USB 2.0 or
USB 1.1 devices such as keyboards, pointing devices, flash disk
drives, external HDDs, speakers, cameras and printers.
Left Side
Power (DC) input port

Insert the bundled power adapter into this port to charge the
battery pack and supply power to your Notebook PC.
WARNING! The adapter may become warm to hot while in use.

Do not cover the adapter and keep it away from your body while
it is connected to a power source.
IMPORTANT! Use only the bundled power adapter to charge the

battery pack and supply power to your Notebook PC.
HDMI port
This port is for the HDMI (High-Definition Multimedia Interface)
connector and is HDCP compliant for HD DVD, Blu-ray, and other
protected content playback.
USB 3.1 Gen 1 port

The USB 3.1 (Universal Serial Bus 3.1) Gen 1 port provides a
transfer rate of up to 5 Gbit/s and is backward compatible to USB
2.0.
USB 3.1 Gen 2 Type-C™ port

The USB 3.1 (Universal Serial Bus 3.1) Gen 2 Type-C™ port
provides a transfer rate of up to 10 Gbit/s and is backward
compatible to USB 2.0.
NOTE: Transfer rate of this port may vary per model.
Status indicators
The status indicators help identify the current hardware status of
your Notebook PC.
Two-color battery charge indicator

The two-color LED provides a visual indication of the
battery’s charge status. Refer to the following table
for details:
Color Status
Solid White The Notebook PC is plugged to
a power source and the battery
power is between 95% and
100%.
Solid Orange The Notebook PC is plugged
to a power source, charging its
battery, and the battery power
is less than 95%.
Blinking Orange The Notebook PC is running on
battery mode and the battery
power is less than 10%.
Lights off The Notebook PC is running on

battery mode and the battery
power is between 10% to 100%.
Power indicator
The power indicator lights up when the Notebook PC
is turned on and blinks slowly when the Notebook
PC is in sleep mode.
Chapter 2:
Using your Notebook PC
Getting started
Charge your Notebook PC
A. Connect the DC power connector into your Notebook PC’s power
(DC) input port.
B. Plug the AC power adapter into a 100V~240V power source.
Charge the Notebook PC for 3 hours before using it in

battery mode for the first time.
NOTE: The power adapter may vary in appearance, depending on models

and your region.
IMPORTANT!
Power adapter information:
• Input voltage: 100-240Vac
• Input frequency: 50-60Hz
• Rating output current: 2.37A (45W) / 3.42A (65W)
• Rating output voltage: 19V
IMPORTANT!
• Locate the input/output rating label on your Notebook PC and

ensure that it matches the input/output rating information on your
power adapter. Some Notebook PC models may have multiple rating
output currents based on the available SKU.
• Ensure that your Notebook PC is connected to the power adapter

before turning it on for the first time. We strongly recommend that
you use a grounded wall socket while using your Notebook PC on
power adapter mode.
• The socket outlet must be easily accessible and near your Notebook
PC.
• To disconnect your Notebook PC from its main power supply, unplug

your Notebook PC from the power socket.
WARNING!
Read the following precautions for your Notebook PC’s battery:
• Only ASUS-authorized technicians should remove the battery inside

the device (for non-removable battery only).
• The battery used in this device may present a risk of fire or chemical
burn if removed or disassembled.
• Follow the warning labels for your personal safety.
• Risk of explosion if battery is replaced by an incorrect type.
• Do not dispose of in fire.
• Never attempt to short-circuit your Notebook PC’s battery.
• Never attempt to disassemble and reassemble the battery

(for non-removable battery only).
• Discontinue usage if leakage is found.
• The battery and its components must be recycled or disposed of

properly.
• Keep the battery and other small components away from children.
Lift to open the display panel
Press the power button
Using the touchpad
Moving the pointer
You can tap anywhere on the touchpad to activate its pointer, then slide
your finger on the touchpad to move the pointer onscreen.
Slide horizontally
Slide vertically
Slide diagonally
One-finger gestures
Tap/Double-tap
• Tap an app to select it.

• Double-tap an app to launch it.
Drag and drop
Double-tap an item, then slide the same finger without lifting it off the
touchpad. To drop the item to its new location, lift your finger from the
touchpad.
Left-click Right-click
• Click an app to select it. Click this button to open the right-
click menu.
• Double-click an app to
launch it.
NOTE: The areas inside the dotted line represent the locations of the left
mouse button and the right mouse button on the touchpad.
Two-finger gestures
Tap
Tap two fingers on the touchpad to simulate the right-click function.
Two-finger scroll (up/down) Two-finger scroll (left/right)
Slide two fingers to scroll up or Slide two fingers to scroll left or

down. right.
Zoom out Zoom in
Bring together your two fingers on Spread apart your two fingers on
the touchpad. the touchpad.
Drag and drop
Select an item then press and hold the left button. Using your other
finger, slide on the touchpad to drag the item, lift your finger off the
button to drop the item.
Three-finger gestures
Tap
Tap three fingers on the touchpad to invoke Cortana.
Swipe left/Swipe right
If you opened multiple apps, swipe three fingers left or right to switch
between these apps.
Swipe up Swipe down
Swipe up to see an overview of all Swipe down to show the desktop.

the apps currently opened.
Four-finger gestures
Tap
Tap four fingers on the touchpad to invoke Action Center.
Customizing your touchpad

1. Launch All settings from the Action Center.
2. Select Devices, then select Mouse & touchpad.
3. Adjust the settings to your preference.
Using the keyboard
HotKeys
The HotKeys on your Notebook PC’s keyboard can trigger the following
commands:
Turns the speaker on or off
Turns the speaker volume down
Turns the speaker volume up
Decreases display brightness
Increases display brightness
Enables or disables the touchpad
Adjusts brightness for the backlit keyboard
Toggles the display mode
NOTE: Ensure that the second display is connected to

your Notebook PC.
Home key
End key
Page up key
Page down key
Function keys
Press to enable or disable the function keys feature.
When the function keys feature is enabled, you can also access HotKeys
by holding down in combination with the top row keys.
Other key combination
Toggles the scroll lock key
Simulates the system request key
Simulates the pause key
Simulates the break key
Displays the drop-down menu
Chapter 3:
Working with Windows® 10
Starting for the first time
When you start your Notebook PC for the first time, a series of screens
appear to guide you in configuring your Windows® 10 operating system.
To start your Notebook PC for the first time:
1. Press the power button on your Notebook PC. Wait for a few
minutes until the setup screen appears.
2. From the setup screen, pick your region and a language to use on
your Notebook PC.
3. Carefully read the License Terms. Select I accept.
4. Follow the onscreen instructions to configure the following basic
items:
• Personalize
• Get online
• Settings
• Your account
5. After configuring the basic items, Windows® 10 proceeds to install

your apps and preferred settings. Ensure that your Notebook PC
is kept powered on during the setup process.
6. Once the setup process is complete, the Desktop appears.
NOTE: The screenshots in this chapter are for reference only.
Start menu
The Start menu is the main gateway to your Notebook PC’s programs,
Windows® apps, folders, and settings.
Change account settings, lock, or sign out from your account
Launch an app from the Start screen
Launch Taskview Launch an app from the taskbar

Launch Search
Launch the Start menu
Launch All apps
Shut down, restart, or put your Notebook PC to sleep
Launch Settings
Launch File Explorer
You can use the Start menu to do these common activities:
• Start programs or Windows® apps

• Open commonly used programs or Windows® apps
• Adjust Notebook PC settings
• Get help with the Windows operating system
• Turn off your Notebook PC
• Log off from Windows or switch to a different user account
Launching the Start menu
Position your mouse pointer over the Start button

in the lower-left corner of your desktop then click it.
Press the Windows logo key on your keyboard.
Opening programs from the Start menu

One of the most common uses of the Start menu is opening programs
installed on your Notebook PC.
Position your mouse pointer over the program then

click to launch it.
Use the arrow keys to browse through the programs.

Press to launch it.
NOTE: Select All apps at the bottom of the left pane to display a full list of
programs and folders on your Notebook PC in alphabetical order.
Windows® apps
These are apps pinned on the right pane of the Start menu and
displayed in tiled-format for easy access.
NOTE: Some Windows® apps require signing in to your Microsoft account

before they are fully launched.
Working with Windows® apps
Use your Notebook PC’s touchpad or keyboard to launch, customize,
and close apps.
Launching Windows® apps from the Start menu
Position your mouse pointer over the app then click to

launch it.
Use the arrow keys to browse through the apps. Press

to launch an app.
Customizing Windows® apps

You can move, resize, unpin, or pin apps to the taskbar from the Start
menu using the following steps:
Moving apps
Position your mouse pointer over the app, then drag and
drop the app to a new location.
Resizing apps
Position your mouse pointer over the app and right-click

it, then click Resize and select an app tile size.
Use the arrow keys to navigate to the app.

Press , then select Resize and select an app
tile size.
Unpinning apps

it, then click Unpin from Start.

Press , then select Unpin from Start.
Pinning apps to the taskbar

it, then click Pin to taskbar.

Press , then select Pin to taskbar.
Pinning more apps to the Start menu
From All apps, position your mouse pointer over the

app you want to add to the Start menu and right-click it,
then click Pin to Start.
From All apps, press on the app that you

want to add to the Start menu, then select Pin to Start.
Task view
Quickly switch between opened apps and programs using the task view
feature, you can also use task view to switch between desktops.
Launching task view
Position your mouse pointer over the icon on the

taskbar and click it.
Press on your keyboard.
Snap feature
The Snap feature displays apps side-by-side, allowing you to work or
switch between apps.
Snap hotspots
You can drag and drop apps to these hotspots to snap them into place.
Using Snap
1. Launch the app you wish to snap.

2. Drag the title bar of your app and drop the app to
the edge of the screen to snap.
3. Launch another app and repeat the above steps to
snap another app.
1. Launch the app you wish to snap.
2. Press and hold the key, then use the arrow

keys to snap the app.
3. Launch another app and repeat the above steps to
snap another app.
Action Center
Action Center consolidates notifications from apps and presents a single
place where you can interact with them. It also has a really useful Quick
Actions section at the bottom.
Launching Action Center
Position your mouse pointer over the icon on the

taskbar and click it.
Press on your keyboard.
Other keyboard shortcuts
Using the keyboard, you can also use the following shortcuts to help
you launch applications and navigate Windows® 10.
Launches Start menu

\
Launches Action Center
Launches the desktop
Launches the File Explorer
Launches Settings
Launches Connect panel
Activates the Lock screen
Minimizes all currently active windows
Launches Search
Launches Project panel
Opens the Run window
Opens Ease of Access Center
Opens the context menu of the Start button
Launches the magnifier icon and zooms in

your screen
Zooms out your screen
Connecting to wireless networks
Wi-Fi
Access emails, surf the Internet, and share applications via social
networking sites using your Notebook PC’s Wi-Fi connection.
IMPORTANT! Airplane mode disables this feature. Ensure that Airplane

mode is turned off before enabling the Wi-Fi connection of your
Notebook PC.
Connecting Wi-Fi
Connect your Notebook PC to a Wi-Fi network by using the following
steps:
1. Select the icon from the taskbar.
2. Select the icon to enable Wi-Fi.
3. Select an access point from the list of available Wi-Fi

connections.
4. Select Connect to start the network connection.
NOTE: You may be prompted to enter a security key to

activate the Wi-Fi connection.
Bluetooth
Use Bluetooth to facilitate wireless data transfers with other Bluetooth-
enabled devices.
IMPORTANT! Airplane mode disables this feature. Ensure that Airplane

mode is turned off before enabling the Bluetooth connection of your
Notebook PC.
Pairing with other Bluetooth-enabled devices

You need to pair your Notebook PC with other Bluetooth-enabled
devices to enable data transfers. Connect your devices by using the
following steps:
1. Launch Settings from the Start menu.

2. Select Devices, then select Bluetooth to search for
Bluetooth-enabled devices.
3. Select a device from the list. Compare the passcode
on your Notebook PC with the passcode sent to
your chosen device. If they are the same, select
Yes to successfully pair your Notebook PC with the
device.
NOTE: For some Bluetooth-enabled devices, you may be

prompted to key in the passcode of your Notebook PC.
Airplane mode
Airplane mode disables wireless communication, allowing you to use
your Notebook PC safely while in-flight.
NOTE: Contact your airline provider to learn about related in-flight

services that can be used and restrictions that must be followed when
using your Notebook PC in-flight.
Turning Airplane mode on
1. Launch Action Center from the taskbar.
2. Select the icon to enable Airplane mode.
Turning Airplane mode off
1. Launch Action Center from the taskbar.
2. Select the icon to disable Airplane mode.
Turning your Notebook PC off
You can turn off your Notebook PC by doing either of the following
procedures:
• Launch the Start menu, then select >

Shut down to do a normal shutdown.
• From the log-in screen, select > Shut down.
• Press to launch Shut down

Windows. Select Shut down from the drop-down
list then select OK.
• If your Notebook PC is unresponsive, press
and hold the power button for at least four (4)
seconds until your Notebook PC turns off.
Putting your Notebook PC to sleep
To put your Notebook PC to Sleep mode:
• Launch the Start menu, then select >

Sleep to put your Notebook PC to sleep.
• From the log-in screen, select > Sleep.
Press to launch Shut down

Windows. Select Sleep from the drop-down list then
select OK.
NOTE: You can also put your Notebook PC to Sleep mode by pressing the
power button once.
Chapter 4:
Power-On Self-Test (POST)
The Power-On Self-Test (POST)
The POST (Power-On Self-Test) is a series of software-controlled
diagnostic tests that run when you turn on or restart your Notebook PC.
The software that controls the POST is installed as a permanent part of
the Notebook PC’s architecture.
Using POST to access BIOS and Troubleshoot

During POST, you can access the BIOS settings or run troubleshooting
options using the function keys of your Notebook PC. You may refer to
the following information for more details.
BIOS
The BIOS (Basic Input and Output System) stores system hardware
settings that are needed for system startup in the Notebook PC.
The default BIOS settings apply to most conditions of your Notebook
PC. Do not change the default BIOS settings except in the following
circumstances:
• An error message appears onscreen during system bootup and

requests you to run the BIOS Setup.
• You have installed a new system component that requires further
BIOS settings or updates.
WARNING! Using inappropriate BIOS settings may result to system

instability or boot failure. We strongly recommend that you change the
BIOS settings only with the help of a trained service personnel.
Accessing BIOS
Enter the BIOS settings by using any of the following methods:
• Restart your Notebook PC then press during POST.
• Launch the Start menu, and choose Settings > Update &
security > Recovery, then select Restart now under Advanced
startup. When you enter the Advanced startup screen, select
Troubleshoot > Advanced options > UEFI Firmware Settings >
Restart.
BIOS Settings
NOTE: The BIOS screens in this section are for reference only. The actual
screens may differ by model and territory.
EZ Mode
This menu appears when you enter the BIOS setup program and
provides you an overview of the basic system information. To access
the Advanced Mode for the advanced BIOS settings, select Advanced
Mode (F7) or press .
Boot
This menu allows you to set your boot option priorities. You may refer to
the following procedures when setting your boot priority.
1. On the Boot screen, select Boot Option #1.
2. Press and select a device as the Boot Option #1.
Security
This menu allows you to set up the administrator and user password
of your Notebook PC. It also allows you to control the access to your
Notebook PC’s hard disk drive, input/output (I/O) interface, and USB
interface.
NOTE:
• If you install a User Password, you will be prompted to input this

before entering the operating system.
• If you install an Administrator Password, you will be prompted to

input this before entering BIOS.
To set the password:
1. On the Security screen, select Setup Administrator Password

or User Password.
2. Type in a password then press .
3. Re-type to confirm the password then select OK.
To clear the password:
1. On the Security screen, select Setup Administrator Password

or User Password.
2. Type in the current password then press .
3. Leave other fields blank then select OK to continue.

4. Select OK to clear the old password.
NOTE: A keyboard is required to type in the password.
Save & Exit
To keep your configuration settings, select Save Changes and Exit
before exiting the BIOS.
To update the BIOS:
1. Verify the Notebook PC’s exact model then download the latest
BIOS file for your model from the ASUS website.
2. Save a copy of the downloaded BIOS file to a flash disk drive.
3. Connect your flash disk drive to your Notebook PC.
4. Restart your Notebook PC then access the BIOS settings.
5. From the BIOS menu, select Advanced > ASUS EZ Flash 3 Utility,
then press .
6. Locate your downloaded BIOS file in the flash disk drive then
press . Follow the onscreen instructions to complete the
update.
7. After the BIOS update process, select Save & Exit > Restore
Defaults to restore the system to its default settings.
Recovering your system
Using recovery options on your Notebook PC allows you to restore the
system to its original state or simply refresh its settings to help improve
performance.
IMPORTANT!
• Backup all your data files before doing any recovery option on your
Notebook PC.
• Note down important customized settings such as network settings,

user names, and passwords to avoid data loss.
• Ensure that your Notebook PC is plugged in to a power source before

resetting your system.
Windows® 10 allows you to do any of the following recovery options:
• Keep my files - This option allows you refresh your Notebook

PC without affecting personal files (photos, music, videos,
documents).
Using this option, you can restore your Notebook PC to its default
settings and delete other installed apps.
• Remove everything - This option resets your Notebook PC to
its factory settings. You must backup your data before doing this
option.
• Go back to an earlier build - This option allows you to go back
to an earlier build. Use this option if this build is not working for
you.
• Advanced startup - Using this option allows you to perform
other advanced recovery options on your Notebook PC such as:
- Using a USB drive, network connection or Windows recovery
DVD to startup your Notebook PC.
- Using Troubleshoot to enable any of these advanced

recovery options: System Restore, System Image Recovery,
Startup Repair, Command Prompt, UEFI Firmware Settings,
and Startup Settings.
Performing a recovery option

Refer to the following steps if you want to access and use any of the
available recovery options for your Notebook PC.
1. Launch Settings and select Update and security.
2. Under the Update and security option, select Recovery then
select the recovery option you would like to perform.
Tips and FAQs
Useful tips for your Notebook PC
To help you maximize the use of your Notebook PC, maintain its system
performance, and ensure all your data are kept secured, here are some
useful tips that you can follow:
• Update Windows® periodically to ensure that your applications

have the latest security settings.
• Use an anti-virus software to protect your data and keep this
updated too.
• Unless absolutely necessary, refrain from using force shutdown to
turn off your Notebook PC.
• Always backup your data and make it a point to create a backup
data in an external storage drive.
• Refrain from using the Notebook PC at extremely high
temperatures. If you are not going to use your Notebook PC for a
long period of time (at least a month), we recommend that you
take out the battery if the battery is removable.
• Disconnect all external devices and ensure you have the following
items prior to resetting your Notebook PC:
- Product key for your operating systems and other installed
applications
- Backup data
- Log in ID and password
- Internet connection information
Hardware FAQs
1. A black dot, or sometimes a colored dot, appears onscreen
when I turn on the Notebook PC. What should I do?
Although these dots normally appear onscreen, they will not
affect your system. If the incident continues and subsequently
affects system performance, consult an authorized ASUS service
center.
2. My display panel has an uneven color and brightness. How

can I fix this?
The color and brightness of your display panel may be affected
by the angle and current position of your Notebook PC. The
brightness and color tone of your Notebook PC may also vary per
model. You may use the function keys or the display settings in
your operating system to adjust the appearance of your display
panel.
3. How can I maximize my Notebook PC‘s battery life?

You can try doing any of the following suggestions:
• Use the function keys to adjust the display brightness.
• If you are not using any Wi-Fi connection, switch your

system into Airplane mode.
• Disconnect unused USB devices.
• Close unused applications, especially those that take up too

much system memory.
4. My battery charge indicator does not light up. What’s wrong?
• Check whether the power adapter or battery pack is
attached correctly. You may also disconnect the power
adapter or battery pack, wait for a minute, then reconnect
them again to the power outlet and Notebook PC.
• If the problem still exists, contact your local ASUS service

center for assistance.
5. Why is my touchpad not working?
Press to enable your touchpad.
6. When I play audio and video files, why can’t I hear any sound
from my Notebook PC’s audio speakers?
• Press to turn up the speaker volume.
• Check if your speakers were set to mute.
• Check if a headphone jack is connected to your Notebook

PC and remove it.
7. What should I do if my Notebook PC’s power adapter gets lost

or my battery stops working?
Contact your local ASUS service center for assistance.
8. My Notebook PC cannot do keystrokes correctly because my
cursor keeps on moving. What should I do?
Make sure that nothing accidentally touches or presses on your
touchpad while you type on the keyboard. You can also disable
your touchpad by pressing .
Software FAQs
1. When I turn on my Notebook PC, the power indicator lights
up but nothing appears on my screen. What can I do to fix
this?
• Force shutdown your Notebook PC by pressing the power

button for at least four (4) seconds. Check if the power
adapter and battery pack are inserted correctly then turn on
your Notebook PC.

2. What should I do when my screen displays this message:

“Remove disks or other media. Press any key to restart.”?
• Remove all connected USB devices then restart your

Notebook PC.
• Remove any optical discs that are left inside the optical drive
then restart.
• If the problem still exists, your Notebook PC might have a

memory storage problem. Contact your local ASUS service
3. My Notebook PC boots slower than usual and my operating

system lags. How can I fix this?
Delete the applications you recently installed or were not
included with your operating system package then restart your
system.
4. My Notebook PC does not boot up. How can I fix this?
• Remove all connected devices to your Notebook PC then

restart your system.

5. Why can’t my Notebook PC wake up from sleep mode?

• You need to press the power button to resume your last
working state.
• Your system might have completely used up its battery

power. Connect the power adapter to your Notebook PC
and connect to a power outlet then press the power button.
Appendices
Internal Modem Compliancy
The Notebook PC with internal modem model complies with JATE (Japan), FCC
(US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved
in accordance with Council Decision 98/482/EC for pan-European single terminal
connection to the public switched telephone network (PSTN). However due
to differences between the individual PSTNs provided in different countries,
the approval does not, of itself, give an unconditional assurance of successful
operation on every PSTN network termination point. In the event of problems you
should contact your equipment supplier in the first instance.
Overview
On 4th August 1998 the European Council Decision regarding the CTR 21 has
been published in the Official Journal of the EC. The CTR 21 applies to all non
voice terminal equipment with DTMF-dialling which is intended to be connected
to the analogue PSTN (Public Switched Telephone Network).
CTR 21 (Common Technical Regulation) for the attachment requirements for

connection to the analogue public switched telephone networks of terminal
equipment (excluding terminal equipment supporting the voice telephony
justified case service) in which network addressing, if provided, is by means of
dual tone multi-frequency signalling.
Network Compatibility Declaration
Statement to be made by the manufacturer to the Notified Body and the vendor:
“This declaration will indicate the networks with which the equipment is designed
to work and any notified networks with which the equipment may have inter-
working difficulties.”
Statement to be made by the manufacturer to the user: “This declaration will

indicate the networks with which the equipment is designed to work and any
notified networks with which the equipment may have inter-working difficulties.
The manufacturer shall also associate a statement to make it clear where network
compatibility is dependent on physical and software switch settings. It will also
advise the user to contact the vendor if it is desired to use the equipment on
another network.”
Up to now the Notified Body of CETECOM issued several pan-European approvals

using CTR 21. The results are Europe’s first modems which do not require
regulatory approvals in each individual European country.
Non-Voice Equipment
Answering machines and loud-speaking telephones can be eligible as well as
modems, fax machines, auto-dialers and alarm systems. Equipment in which the
end-to-end quality of speech is controlled by regulations (e.g. handset telephones
and in some countries also cordless telephones) is excluded.
This table shows the countries currently under the CTR21
standard.
Country Applied More Testing
Austria1 Yes No
Belgium Yes No
Czech Republic No Not Applicable
Denmark1 Yes Yes
Finland Yes No
France Yes No
Germany Yes No
Greece Yes No
Hungary No Not Applicable
Iceland Yes No
Ireland Yes No
Italy Still Pending Still Pending
Israel No No
Lichtenstein Yes No
Luxemburg Yes No
The Netherlands1 Yes Yes
Norway Yes No
Poland No Not Applicable
Portugal No Not Applicable
Spain No Not Applicable
Sweden Yes No
Switzerland Yes No
United Kingdom Yes No
This information was copied from CETECOM and is supplied without liability. For
updates to this table, you may visit
http://www.cetecom.de/technologies/ctr_21.html.
1 National requirements will apply only if the equipment may use pulse dialling
(manufacturers may state in the user guide that the equipment is only intended to
support DTMF signalling, which would make any additional testing superfluous).
In The Netherlands additional testing is required for series connection and caller
ID facilities.
Federal Communications Commission

Interference Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference

that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of a shielded-type power cord is required in order to meet

FCC emission limits and to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used. Use only shielded
cables to connect I/O devices to this equipment. You are cautioned that changes or
modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
(Reprinted from the Code of Federal Regulations #47, part 15.193, 1993.
Washington DC: Office of the Federal Register, National Archives and Records
Administration, U.S. Government Printing Office.)
This device operates within a 5.15-5.25 GHz frequency range and is restricted for
indoor use only. Outdoor operation within 5150-5250 MHz is prohibited.
FCC Radio Frequency (RF) Exposure Caution

Statement
WARNING! Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure
compliance requirements, please avoid direct contact to the transmitting antenna
during transmitting. End users must follow the specific operating instructions for
satisfying RF exposure compliance.
Wireless Operation Channel for Different
Domains
N. America 2.412-2.462 GHz Ch01 through Ch11
Japan 2.412-2.484 GHz Ch01 through Ch14
Europe ETSI 2.412-2.472 GHz Ch01 through Ch13
Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits. The Wireless Device should be used in such
a manner such that the potential for human contact during normal operation is
minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure
limits under portable exposure conditions (antennas are less than 20 cm of a
person’s body).
Informations concernant l’exposition aux

fréquences radio (RF)
La puissance de sortie émise par cet appareil sans fil est inférieure à la limite
d’exposition aux fréquences radio d’Industrie Canada (IC). Utilisez l’appareil sans fil
de façon à minimiser les contacts humains lors d’un fonctionnement normal.
Cet appareil est conforme aux limites d’exposition aux rayonnements IC établies
pour un environnement exposé à des appareils mobiles (les antennes se situant à
une distance inférieure à 20 cm du corps de l’utilisateur).
Compliance Statement of Innovation, Science
and Economic Development Canada (ISED)
This device complies with Innovation, Science and Economic Development
Canada license exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
Operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems
CAN ICES-3(B)/NMB-3(B)
Déclaration de conformité de Innovation,

Sciences et Développement économique Canada
(ISED)
Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
La bande 5150-5250 MHz est réservée uniquement pour une utilisation à l’intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
CAN ICES-3(B)/NMB-3(B)
Caution
(i) the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile satellite
systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz
and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz
shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-
point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary
users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that
these radars could cause interference and/or damage to LE-LAN devices.
Avertissement
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des
instructions précises sur les restrictions susmentionnées, notamment:
(i) Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement à une utilisation en intérieur afin de réduire les risques d’interférence
préjudiciables aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) Le gain maximal d’antenne permis pour les dispositifs utilisant les bandes
5250-5350 MHz et 5470-5725 MHz doit être conforme à la limite de P.I.R.E; et
(iii) Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-
5825 MHz) doit être conforme à la limite de P.I.R.E spécifiée pour l’exploitation
point à point et non point à point, selon le cas.
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de
radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont
la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars
pourraient créer des interférences et/ou des dommages aux dispositifs LAN-EL.
UL Safety Notices
Required for UL 1459 covering telecommunications (telephone) equipment
intended to be electrically connected to a telecommunication network that has an
operating voltage to ground that does not exceed 200V peak, 300V peak-to-peak,
and 105V rms, and installed or used in accordance with the National Electrical
Code (NFPA 70).
When using the Notebook PC modem, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and injury to persons, including
the following:
• DO NOT use the Notebook PC near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
• DO NOT use the Notebook PC during an electrical storm. There may be a

remote risk of electric shock from lightning.
• DO NOT use the Notebook PC in the vicinity of a gas leak.

Required for UL 1642 covering primary (non-rechargeable) and secondary
(rechargeable) lithium batteries for use as power sources in products. These
batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may
consist of a single electrochemical cell or two or more cells connected in series,
parallel, or both, that convert chemical energy into electrical energy by an
irreversible or reversible chemical reaction.
• DO NOT dispose the Notebook PC battery pack in a fire, as they may

explode. Check with local codes for possible special disposal instructions
to reduce the risk of injury to persons due to fire or explosion.
• DO NOT use power adapters or batteries from other devices to reduce

the risk of injury to persons due to fire or explosion. Use only UL certified
power adapters or batteries supplied by the manufacturer or authorized
retailers.
Power Safety Requirement
Products with electrical current ratings up to 6A and weighing more than 3Kg
must use approved power cords greater than or equal to: H05VV-F, 3G, 0.75mm2 or
H05VV-F, 2G, 0.75mm2.
TV Notices
Note to CATV System Installer—Cable distribution system should be grounded
(earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC),
in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial
Cable – installation should include bonding the screen of the coaxial cable to the
earth at the building entrance.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and
Restriction of Chemicals) regulatory framework, we publish the chemical
substances in our products at ASUS REACH website at
http://csr.asus.com/english/REACH.htm.
Macrovision Corporation Product Notice

This product incorporates copyright protection technology that is protected by
method claims of certain U.S.A. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Prevention of Hearing Loss

To prevent possible hearing damage, do not listen at high volume
levels for long periods.
Nordic Lithium Cautions (for lithium-ion
batteries)
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions. (English)
ATTENZIONE! Rischio di esplosione della batteria se sostituita in modo errato.

Sostituire la batteria con un una di tipo uguale o equivalente consigliata dalla
fabbrica. Non disperdere le batterie nell’ambiente. (Italian)
VORSICHT! Explosionsgefahr bei unsachgemäßen Austausch der Batterie. Ersatz

nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers. (German)
ADVARSELI! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri
tilbage til leverandøren. (Danish)
VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller

en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt
batteri enligt fabrikantens instruktion. (Swedish)
VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan sousittelemaan tyyppiin. Hävitä käytetty paristo
valmistagan ohjeiden mukaisesti. (Finnish)
ATTENTION! Danger d’explosion si la batterie n’est pas correctement remplacée.

Remplacer uniquement avec une batterie de type semblable ou équivalent,
recommandée par le fabricant. Jeter les batteries usagées conformément aux
instructions du fabricant. (French)
ADVARSEL! Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme

batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte
batterier kasseres i henhold til fabrikantens instruksjoner. (Norwegian)
(Japanese)
ВНИМАНИЕ! При замене аккумулятора на аккумулятор иного типа возможно

его возгорание. Утилизируйте аккумулятор в соответствии с инструкциями
производителя. (Russian)
CTR 21 Approval (for Notebook PC with built-in
Modem)
Danish
Dutch
English
Finnish
French
German
Greek
Italian
Portuguese
Spanish
Swedish
ENERGY STAR complied product
ENERGY STAR is a joint program of the U.S. Environmental
Protection Agency and the U.S. Department of Energy helping
us all save money and protect the environment through energy
efficient products and practices.
All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR
standard, and the power management feature is enabled by default. The
monitor and computer are automatically set to sleep within 10 and 30 minutes
of user inactivity. To wake your computer, click the mouse or press any key on
the keyboard. Please visit http://www.energystar.gov/powermanagement for
detail information on power management and its benefits to the environment.
In addition, please visit http://www.energystar.gov for detail information on the
ENERGY STAR joint program.
NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating systems.
Global Environmental Regulation Compliance

and Declaration
ASUS follows the green design concept to design and manufacture our products,
and makes sure that each stage of the product life cycle of ASUS product is in line
with global environmental regulations. In addition, ASUS disclose the relevant
information based on regulation requirements.
Please refer to http://csr.asus.com/english/Compliance.htm for information

disclosure based on regulation requirements ASUS is complied with:
Japan JIS-C-0950 Material Declarations
EU REACH SVHC
Korea RoHS
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
you to be able to responsibly recycle our products, batteries, other components as
well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling

information in different regions.
Rechargeable Battery Recycling Service in

North America
For US and Canada customers, you can call 1-800-822-8837

(toll-free) for recycling information of your ASUS products’
rechargeable batteries.
Coating Notice
IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating

is applied to insulate the device except on the areas where the I/O ports are located.
Regional notice for California
WARNING
Cancer and Reproductive Harm -

www.P65Warnings.ca.gov
Regional notice for Singapore
Complies with This ASUS product complies with IMDA Standards.
IMDA Standards
DB103778
Regional notice for India

This product complies with the “India E-Waste (Management) Rules, 2016” and
prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls
(PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding
0.1% by weight in homogenous materials and 0.01% by weight in homogenous
materials for cadmium, except for the exemptions listed in Schedule II of the Rule.
Notices for removable batteries

• Risk of explosion if battery is replaced by an incorrect type.
• The battery and its component must be recycled or disposed of properly.
Avis concernant les batteries remplaçables

• La batterie de l’appareil peut présenter un risque d’incendie ou de brûlure
si celle-ci est retirée ou désassemblée.
• La batterie et ses composants doivent être recyclés de façon appropriée.
Simplified EU Declaration of Conformity
ASUSTek Computer Inc. hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU. Full
text of EU declaration of conformity is available at
https://www.asus.com/support/.
The WiFi operating in the band 5150-5350 MHz shall be restricted to indoor use
for countries listed in the table below:
AT BE BG CZ DK EE FR
DE IS IE IT EL ES CY
LV LI LT LU HU MT NL
NO PL PT RO SI SK TR
FI SE CH UK HR

Asus Zenbook Ux431fl Manual

Uploaded by

Copyright:

Available Formats

Asus Zenbook Ux431fl Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Asus Zenbook Ux431fl Manual

Uploaded by

Copyright:

Available Formats

E14902

First Edition / December 2018

Copyright © 2018 ASUSTeK COMPUTER INC. All Rights Reserved.

SERVICE AND SUPPORT

Visit our multi-language website at https://www.asus.com/support/

Chapter 1: Hardware Setup

Chapter 2: Using your Notebook PC

Chapter 4: Power-On Self-Test (POST)

Chapter 1: Hardware Setup

Chapter 2: Using your Notebook PC

Chapter 3: Working with Windows® 10

Chapter 4: Power-On Self-Test (POST)

Tips and FAQs

IMPORTANT! This message contains vital information that must be

WARNING! This message contains important information that must be

= Use the touchpad.

= Use the keyboard.

Refer to the rating label on the bottom of your

Do not leave your Notebook PC on your lap or near

Do not use damaged power cords, accessories, and

While powered on, ensure that you do not carry or

You can send your Notebook PC through x-ray

Disconnect the AC power and remove the battery

Do not use strong solvents such as thinners,

Do not place objects on top of your Notebook PC.

Do not expose your Notebook PC to strong

Do not use or expose your Notebook PC near

Do not expose your Notebook PC to dusty

Do not use your Notebook PC near gas leaks.

Do not throw your Notebook PC in municipal waste.

Do not throw the battery in municipal waste. The

NOTE: The keyboard layout differs by model or territory.

Capital lock indicator

Function key lock indicator

Fingerprint sensor (on selected models)

NOTE: The bottom side may vary in appearance depending on model.

• Battery time varies by usage and by the specifications for this

• Purchase components from authorized retailers to ensure maximum

WARNING! Ensure that paper, books, clothing, cables, or other

Memory card reader

USB 2.0 port

Power (DC) input port

WARNING! The adapter may become warm to hot while in use.

IMPORTANT! Use only the bundled power adapter to charge the

USB 3.1 Gen 1 port

USB 3.1 Gen 2 Type-C™ port

NOTE: Transfer rate of this port may vary per model.

Two-color battery charge indicator

Lights off The Notebook PC is running on

Charge the Notebook PC for 3 hours before using it in

NOTE: The power adapter may vary in appearance, depending on models

Power adapter information:

• Input voltage: 100-240Vac

• Input frequency: 50-60Hz

• Rating output current: 2.37A (45W) / 3.42A (65W)

• Rating output voltage: 19V

• Locate the input/output rating label on your Notebook PC and

• Ensure that your Notebook PC is connected to the power adapter

• To disconnect your Notebook PC from its main power supply, unplug

Read the following precautions for your Notebook PC’s battery: