0% found this document useful (0 votes)
104 views4 pages

Ntelligent Detection Devices: Data Sheet

Uploaded by

Mazenabs Abs
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
104 views4 pages

Ntelligent Detection Devices: Data Sheet

Uploaded by

Mazenabs Abs
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Data Sheet

s Fire Safety Products

Intelligent Detection Devices


Thermal (Heat) Detector
Model FDT421
ARCHITECT AND ENGINEER SPECIFICATIONS
Provides seven (7) field-selectable settings in the 135° 174°F (57.2° 78.9°C) temperature range
Tri-color detector-status light-emitting diode (LED) with 360° viewing
Compatible with Model DPU (device programmer / loop tester)
Utilizes advanced microprocessor-based signal processing
Polarity insensitive utilizing SureWireTM technology
Provides a low-temperature warning at 40°F (4.4°C)
Each detector is self-testing:
complete diagnostics performed every 10 seconds
Compatible with Model DB-11 series mounting bases
Field programmable as rate-of-rise or fixed temperature
Compatible with Siemens Model ‘H’-series devices on the
same loop (with FireFinder® XLS and Desigo fire systems)
Superior EMI / RFI immunity UL521 Listed and ULC Listed;
Restriction of Hazardous Substances FM (#3230, 3210),
(RoHS) compliant CSFM (#72720067:0258) Approved
Product Overview
The Model FDT421 Intelligent Thermal (Heat) Additionally, Model FDT421 can be configured to provide
Detector provides an advanced method of detection, a low-temperature warning signal at 40°F (4.4°C). With
address programming and supervision combined use of a compatible FACP (FireFinder XLS and Desigo Fire
with sophisticated FACP communication. Model Safety panels), this feature serves as prevention of water
FDT421 uses a state-of-the-art thermistor, freezing in pipes for sprinkler systems, and meets NFPA
microprocessor and advanced signal analysis, 72 code.
providing high reliability and accuracy. Model DPU
Further, Model FDT421 is a cost-effective two-wire / Model FDT421 is compatible with the Siemens field-device
addressable thermal detector that provides a unique, programmer / test unit (Model DPU), which is a compact,
advanced feature: field-selectable temperature portable, menu-driven accessory for electronically
settings specially tailored for application-specific programming and testing detectors, easily and reliably.
detection needs.
Model DPU eliminates the need for cumbersome, unreliable
Model FDT421 provides seven (7) field-selectable mechanical programming methods such as dials or
temperature-range settings: 135°F (57°C) 174°F switches and reduces installation and service costs by
(79°C) with fixed and rate-of-rise programmability. electronically programming and testing the detector prior to
This variance provides the customer with maximum installation. Each detector consists of a solid state, non-
flexibility to program the temperature settings to suit mechanical thermal sensor, and microprocessor-based
multiple application needs and changing electronics with a low-profile plastic housing.
environmental conditions.
Model FDT421 is Underwriters’ Laboratories ( UL521)
Listed as a thermal (heat) detector.

Thermal (Heat) Detector 6151


s Industry, Inc.
Building Technologies Division
Product Overview (continued)
Each Model FDT421 detector base also contains a A quick visual inspection is sufficient to indicate the condition
provision for an optional, concealed locking mechanism of the detector at any time. If more detailed information is
to prevent unauthorized removal of the detector head required, a printed report can be provided from the Model
(Model LK-11.) FC20-series FACPs indicating the status and settings assigned
For proper operation of Model DPU, the technician selects to each individual detector.
the accessory’s program mode, and enters the desired
address. In turn, Model DPU automatically sets and verifies Installation
the address, as well as tests the detector. When in the ‘test’ All Model FDT421 detectors use a surface-mounting base,
mode, Model DPU will perform a series of diagnostic tests Model DB-11 or Model DB-11E, which mounts on a 4-inch
without altering the address or other stored data, allowing octagonal, square or single-gang electrical box. The base
techs to determine if the detector is operating properly. utilizes screw-clamp contacts for electrical connections and
Model DPU operates on AC power or rechargeable batteries, self-wiping contacts for increased reliability.
providing flexibility and convenience in programming and The Model DB-11 base can be used with the optional Model
testing equipment from practically any location. LK-11 detector locking kit, which contains 50 detector locks
and an installation tool to prevent unauthorized removal of
Operation the detector head. Model DB-11 has decorative plugs to
Model FDT421 also utilizes a modern, accurate and shock- cover the outer mounting screw holes.
resistant thermistor to sense temperature changes: Model FDT421 may be installed on the same initiating
circuit with the following Siemens Model ‘H’-series
detectors [when used with FireFinder XLS and Desigo
Fire Safety panels]
• Model HFP-11
• Model ‘HMS’-series manual stations
• Model ‘HTRI’-series interfaces
• Model HCP output-control devices
• Model ‘HZM’-series of addressable,
conventional zone modules

Each Model FDT421 detector provides seven (7) pre- Application Data
programmed, FACP-selectable parameter sets. Installation of Model FDT421 detectors requires a (2) two-
Detector Supervision and Testing wire circuit. In many retrofit cases, existing wiring may be
used. ’T-tapping’ is permitted only for Style 4 (Class B)
Model FDT421, which is listed as a self-testing device,
wiring. Model FDT421 is polarity insensitive, which allows
contains a tri-color light emitting diode (LED) indicator,
a substantial reduction in installation and debugging time.
capable of flashing any one (1) of three (3) distinct colors:
Green, Yellow, or Red. During each flash interval, the Model FDT421 can be applied within the maximum 50-feet
microprocessor-based detector monitors the following: center spacing (2,500 sq. ft. areas), per UL. This application
• Temperatures reaching programmed thresholds guideline is based on ideal conditions specifically, smooth
• Internal sensors and electronics are functional ceiling surfaces, minimal air movement, and no physical
obstructions between potential fire sources and the actual
Based on the monitoring results, the LED indicator flashes detector. Do not mount detectors in close proximity to
the following colors based on the following conditions: ventilation or heating and air conditioning outlets. Exposed
Flash joints or beamed ceilings may also affect safe spacing
Flash
Condition Interval limitations for detectors.
Color
(in seconds)
Should questions arise regarding detector placement,
Normal supervisory operation.
observe NFPA 72 guidelines. Good fire-protection system
Temperature has not reached 10
Green*: engineering and common sense dictate how and when fire
programmed alarm thresholds
or set points. detectors are installed and used. Contact your local
Detector is in trouble and Siemens Fire Safety distributor or sales office whenever
Yellow: 4
needs replacement. you need assistance applying Model FDT421 in unusual
Red: Alarm condition. 1 applications. Be sure to follow NFPA guidelines and UL
Listed / ULC Listed installation instructions included with
No Flash: Detector is not powered.
every Siemens Fire Safety detector and local codes as
* LED can be turned OFF. for all fire protection equipment.
Please follow the corresponding description of the panel used.

s Industry, Inc.
Building Technologies Division
Specifications Technical Data
Model FDT421 is a plug-in, (2) two-wire thermal (heat) Operating
detector, compatible with FireFinder XLS and Desigo Temperature +32°F (0°C) to 100°F (38°C)
Fire Safety panels. Each Model FDT421 detector has Range: [with 135°F (57°C) alarm-threshold setting]
microcomputer-chip technology and highly stable, solid-
Relative Humidity: 0-95%; non-condensing
state electronic circuitry.
The Model FDT421 detector utilizes a modern, accurate Air Pressure: No effect
and shock-resistant thermistor to sense temperature
Input Voltage Range: 16VDC 30VDC
changes.
This electronic-sensing method virtually eliminates thermal Alarm Current (max.): 410 A
lag associated with mechanical temperature-sensing
Standby Current (max.): 250 A, max.
devices, and provides almost instantaneous temperature
(Average )
status to the FACP.
Model FDT421 provides seven (7) field-selectable, pre- Maximum Spacing: 50-foot centers (2,500 sq. ft.),
programmed temperature settings: per NFPA 72 and ULC-S524
• Fixed 135°F (57°C)
• Fixed 145°F (63°C)
Thermal Rating:
• Fixed 155°F (68°C) Model FDT421 provides up to seven (7) field-selectable, pre-
• Fixed 165°F (74°C) programmed temperature settings:
• Fixed 174°F (79°C) Fixed 135°F (57°C)
• Rate-of-Rise: 15°F / min. (8.3°C) at fixed 135°F (57°C) Fixed 145°F (63°C)
• Rate-of-Rise: 15°F / min. (8.3°C) at fixed 174°F (79°C) Fixed 155°F (68°C)
Fixed 165°F (74°C)
Additionally, the Model FDT421 detector has the Fixed 174°F (79°C)
following optional feature:
Rate-of-Rise: 15°F / min. (8.3°C / min) at fixed 135°F (57°C)
• Model FDT421 provides indication of potential freezing Rate-of-Rise: 15°F / min. (8.3°C / min) at fixed 174°F (79°C)
for sprinkler systems, via a configuration for reporting a
low-temperature warning of 40°F (4.4°C). Detector Weight:
This feature is compatible with Models FC2025, FC2050 0.32 Lbs.
and FireFinder XLS. (0.144 Kg.)

s Industry, Inc.
Building Technologies Division
Mounting Diagram Details for Ordering
Dimensions Part
Model Number Description
FDT421 S54320-F5-A1 Thermal (Heat) Detector
DB-11 500-094151 Detector Mounting Base
DB-11E 500-094151E Detector Base {small}
DB2-HR S54320-F12-A1 Relay Base
Remote Alarm Indicator:
RL-HC 500-033230
4” octagon-box mount, red
Remote Alarm Indicator:
RL-HW 500-033310
Compatible FACPs Single-gang box mount, red
LK-11 500-695350 Base Locking Kit
Data
Model Sheet Description STI-9604 STI Mechanical Protection Guard
Number See: www.ST I-USA.com for further details on ordering
6300 FireFinder XLS Model STI-9604.
FC2005 6813 50-point addressable FACP
FC2025 6815 252-point addressable FACP
FC2050 6815 504-point addressable FACP
In Canada, order:
Part
Model Number Description

DB-11C 500-095687 Detector Mounting Base


for Series 11 Detectors ( ULC Listed)

Notice: This marketing data sheet is not intended to be used for system design or installation purposes.
For the most up-to-date information, refer to each product’s installation instructions.

Fire Safety Fire Safety


8 Fernwood Road 1577 North Service Road
s Industry, Inc. Florham Park, NJ 07932 East Oakville, Ontario April 2014
Building Technologies Division Tel: (973) 593-2600 (SII-FS) L6H 0H6 / Canada Supersedes sheet dated 11/13
FAX: (908) 547-6877 Printed in U.S.A. Tel: [905] 465-8000 (Rev. 4)

URL: www.usa.Siemens.com/Fire URL: www.Siemens.C A

You might also like