Scribd
Upload
45 views2 pages

C. ISO/IEC 15693

The document contains questions about RFID/NFC standards, protocols, and functions. It also contains two circuit analysis questions where increasing aspects of the circuit results in longer times to reach a stable 3.3V output. Additionally, it asks questions about temperature differences and power output based on specifications in a thermoelectric generator datasheet.

Uploaded by

Krushnasamy Suramaniyan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
45 views2 pages

C. ISO/IEC 15693

The document contains questions about RFID/NFC standards, protocols, and functions. It also contains two circuit analysis questions where increasing aspects of the circuit results in longer times to reach a stable 3.3V output. Additionally, it asks questions about temperature differences and power output based on specifications in a thermoelectric generator datasheet.

Uploaded by

Krushnasamy Suramaniyan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

1. Which RFID/NFC standard is used in Libre Pro Sensor?

a. Felica
b. ISO/IEC 18000-3
c. ISO/IEC 15693
d. ISO/IEC 14443
2. In RFID, what is the function of the inventory command
a. To know which tags are near by
b. To get the UUID of the targeted device
c. To read the desired device data by using UUID
d. All the above
e. None the above
3. What are the different types of RFID/NFC protocol supported by TRF7970A?
a. Felica
b. ISO/IEC 18000-3
c. ISO/IEC 15693
d. ISO/IEC 14443 A
e. ISO/IEC 14443 B
4. In the above-mentioned circuit, if the amplitude is increased by 1.5 times and output capacitor
is increased by 2 times. What will be the time taken to obtain a stable output of 3.3V?
Solution: Amplitude = 15 * 1.5 = 22.5 V
Output capacitor = 47u * 2 = 94uF

Time taken to get stable output of 3.3 V = 52.47ms or 0.052s


(Range: 51.00ms – 53.00ms) or (Range: 0.051s – 0.053s)
5. In the above-mentioned circuit, if the frequency is increased by 2 times and storage capacitor is
increased by 2.5 times. What will be the time taken to obtain a stable output of 3.3V?
Solution: Frequency = 100 * 2 = 200Hz
Storage capacitor = 22u * 2.5 = 55uF

89.652ms
(Range: 87.00ms – 90.00ms)
6. From the datasheet of Teg1-12611-6, to harvest the maximum amount of energy, what is the
required hot side temperature if cold side temperature is maintained at 30o C.
a. 300o C
b. 250o C
c. 150o C
d. 50o C
7. From the datasheet of Teg1-12611-6 for Th = 225o C and Tc = 30o C, the open circuit voltage
obtained is
a. 4 – 6 V
b. 7 – 8 V
c. 6 – 7 V
d. 3 – 4 V
8. From the datasheet of Teg1-12611-6 for Th = 200o C and Tc = 50o C, the output power obtained
is
a. 5 – 6 W
b. 3 – 4 W
c. 1 – 2 W
d. 6 – 7 W

You might also like