SERVICE MANUAL

HOT COOL & COLD HIDDEN BOTTLE

WATER COOLER

MODEL:
SWD-82EHL-PB

In the interests of user-safety (Required by safety regulations

in some countries) the set should be restored to its original
condition and only parts identical to those specified should
be used.

CONTENTS

WIRING DIAGRAMS ..............................................................1

WIRE CONNECTION DIAGRAM ...........................................2
WATER FLOW & REFRIGERATION DIAGRAMS..................3
OPERATION GUIDE ..............................................................4
ASSEMBLY DRAWING ..........................................................7
EXPLODE DRAWINGS ..........................................................8
TROUBLE SHOOTING ...........................................................11
HOW TO CHANGE PARTS ....................................................12

Parts marked with " " are important for maintaining the safety of the set. Be sure to
replace these parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used for
SHARP CORPORATION after sales service only.
The contents are subject to change without notice.
page 1 Wiring diagrams

1. Wiring diagram
1.1 Wiring diagram for BL (No display)

Electrical Wiring Diagram of SWD-82EHL-SL

14V
AC
Heating

Heating
Cooling
Cooling

Relay

Triac
Pump

Cold water sensor

Main control board
Hot water sensor 1

Compressor
Hot water sensor 2 MCU Dry-burn
thermostat
Magnetic sensor (manual reset )
M
Water level sensor
~ thermostat
Heating switch (autoreset)
Cooling switch
Power change switch
Heater
LED board

N
E
 Wire connection diagram page 2

2. Wire connection diagram

2.1 Wire connection diagram for BL (with fuse,No display, No Ozonator)

Hot tank

Compressor

P13

P3
P4

P6

Fuse Power
change
P8 P17 switch

P10
P18

Float assembly
with electrodes
P9
P15
Power cord

P5 Hot water
sensor 1

P7 P12 P24 P25 P19 P26 P16 P14

Transformer

Ozone
LED
Cold water sensor

Hot water sensor 2

generator
Water pump board

Cooling Door
switch switch

Heating
switch

Number
Item Drawing No/PN Description Color Length (mm) Connector1 Connector2
of wires

Black+brown 2000+20+300 250 female terminal

1 6WP100F41B00 Power cord 3 Black+yellowgreen 2000+20+200 NA (Power cord) Ring terminal

Black+blue 2000+20+300 250 female terminal

2 6WA035F01B Fuse wire 1 Black 350 250 female terminal 187 female terminal

Dry burnt thermostat to heater (with

3 6WA065X11W 1 White 70 250 female terminal 250 female terminal
temperature fuse)

4 6WA075F01W Hot tank wire 1 White 750 250 female terminal 250 female terminal

5 6WA075F01B Hot tank wire 1 Black 750 250 female terminal 250 female terminal

6 6WA065FX1W Compressor wire 1 White 650 250 female terminal 250 flag female terminal

7 6WA065FX1L Compressor wire 1 Blue 650 250 female terminal 250 flag female terminal

8 6WA090BX1R Hot tank sensor 1 Red 900 Interior XHB-2Y

9 6WA090BX1B Hot tank sensor 1 Black 900 Interior XHB-2Y

10 6WA090BX1W Cool water sensor 1 White 900 Interior XHB-2Y

11 6WB000B11B00 Door switch wire 1 Black 1150 Interior XHB-2Y

12 6WA200F41E Compressor ground wire 1 Yellowgreen 200 Ring terminal Ring terminal

13 6WB085C11X00 Water pump wire1 1 Black+red 850 VH-2 42000-02P

14 6WB010C11X00 Water pump wire2 1 Black+red 100 Welding on motor 42000-02R

15 6WB060BX1X Water level wire 1 White+green+yellow 600 250 female terminal XHB-3Y

16 6WB045B02X Power change switch wire 1 White+yellow 450 187 female terminal XHB-2Y

17 6WB045B05X Heating switch wire 1 White+Red 450 187 female terminal XHB-2Y

18 6WB045B04X Cooling switch wire 1 White+Black 450 187 female terminal XHB-2Y

19 6WB000B12X Ozone wire 1 Red+green+Black 250+100+250 Interior XHB-3Y

20 6WA055B01W02 Coennect control board wire 1 White 550 XH-6Y XHB-6Y

page 3 Water flow and Refrigeration diagrams

3. Water flow diagram

water level sensing electrodes

Mechanical valve
with switch
Ozone Hot air return

Baffle
plate Cold water
Reservior

Cold tap

Cook tap
Optional

Hot tap

Hot water
tank

Drain cap

Air filter
Probe pump
assembly

Water
bottle

4. Refrigeration diagram

Condenser

Evaporator

Cold water
sensor

Capillary

Dry Filer

Compressor
 Operation guide page 4

5. Operation guide
CAUTION
This dispenser is intended for water dispensing only. Do NOT use other liquids. Do NOT use for other purposes. Warranty
is void if used for any other liquids including coffee, tea, juices, beer or wine.
This dispenser has been designed to use water bottles with a 3, 5 or 5.2 gallon capacity. Do NOT use alternative bottles.

Initial Set Up
Do NOT plug in until steps 1-3 are completed.

1. Allow unit to sit upright for 4 hours. A

2. Set probe length.
• If using a 5 gallon round bottle, use the probe as it is supplied.
• If using a 5 gallon rectangular bottle, use the probe as it is supplied.
• If using a 3 gallon bottle, remove section B. Save for future use.
3. Install bottle.
• Open door and place fresh bottle in front of tray. B
• Clean fresh bottle with a soft cloth and warm soapy water then inse.
• Remove entire plastic cap from top of bottle.
• Insert probe into bottle.
• Push down on probe until it is seated.
NOTICE: When using a 5 gallon rectangular bottle, slide into place as shown in llustration below.
4. Plug cord into a properly grounded wall outlet.

• Water will be pumped into hot and cold water reservoirs from the bottle.
5. Turn energy saving switches on back of dispenser to ON.
• The red switch controls the heating of water. If you do not want hot water, leave this switch OFF
• The blue switch controls the cooling of water. If you do not want cold water, leave this switch OFF.

Notice:
• It will take up to 3 minutes for the reservoirs to load.
• Diring the use pump will come on to refill the tanks ,This is normal.
page 5 Operation guide

CAUTION
Initial Rinsing of Water Lines
This unit has been tested and sanitized prior to packing and shipping. During transit
dust and odors can accumulate in the tank and lines. fill with water.wait for 30 minutes,Dispense
classes of hot water and 6 glasses of cold water.

Dispense Cold Water

Note: After setup, it will take 1 hour to get water to cold temperature. During this time the compressor may run
continuously. This is normal.
1. Position bottle, glass, pitcher or cooking pot securely below cold water tap.
• The right triangle below the cold water control indicates the location of the cold water tap.
• The circular shapes in the drip plate help align the flow of water. This unit dispenses water at a fast rate. To avoid
splashes, hold cup as close to the tap as possible.
2. Depress right control downward to start flow.
3. Release control once desired fill level is achieved.

Dispense Hot Water

This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with hot water. Keep children
and pets away from unit while dispensing. Never allow children to dispense hot water without proper and direct supervision.
Note: After setup, hot water will be available in 15-20 minutes.
1. Position bottle, glass, pitcher or cooking pot securely below hot water tap.
• The left triangle below the hot water control indicates the location of the hot water tap.
• The circular shapes in the drip plate help align the flow of water. This unit dispenses water at a fast rate. To avoid
splashes, hold cup as close to the tap as possible.
2. Push hot water release button (red) inward and depress control downward to start flow.
3. Release control once desired fill level is achieved.

Replace an Empty Bottle

Notice: When your bottle is empty the dispenser will beep intermittently and the LED light of EMPTY BOTTLE will blink
until a fresh bottle is connected.
You may also hear a sucking sound when the bottle empties. This is normal and is another way to be alerted that your
bottle is empty.
Replace empty bottle as soon as you notice it is empty. If unavailable, leave door ajar or unplug cooler to stop beeping
noise and flashing lights.
There may be a small amount of water left in the bottle. This is normal, if you need assistance please contact customer
service.
1. Open door and slide bottle out.
2. Remove probe from bottle:
• Pull probe straight up until completely out of bottle.
•hang probe on the door.
3. Install fresh bottle:
 Operation guide page 6

• Place fresh bottle in front of tray.

• Clean fresh bottle with a soft cloth and warm soapy water then wepe with clean wet colth.
• Remove entire plastic cap from top of bottle.
• Insert probe into bottle.
• Push down on probe until it is seated.
• Slide bottle onto tray and close door completely.

6. Precautions

To reduce risk of injury and property damage, user must read this entire manual before assembling, installing & operating
dispenser.
Failure to execute the instructions in this manual can cause personal injury or property damage.

7. Assembly drawing and part list

WARNING
This product dispenses water at very high temperatures. Failure to use properly can cause personal injury.
When operating this dispenser, always exercise basic safety precautions, including the following:
• Prior to use, this dispenser must be properly assembled and installed in accordance with this manual.
• This dispenser is intended for water dispensing only. Do NOT use other liquids. Do NOT use for other
purposes. Never use any other liquid in the dispenser other than known and microbiologically safe bottled
water. Warranty is void if used for any other liquids including coffee, tea, juices, beer or wine.
• For indoor use only. Keep water dispenser in a dry place away from direct sunlight. Do NOT use outdoors.
• Install and use only on a hard, flat and level surface.
• Do NOT place dispenser into an enclosed space or cabinet.
• Do NOT operate dispenser in the presence of explosive fumes.
• Position back of dispenser no closer than 4 inches from wall and permit free airflow between wall and
dispenser. There must be at least 4 inches clearance on the sides of the dispenser to permit airflow.
• Use only properly grounded outlets.
• Do not use an extension cord with your water dispenser.
• Always grasp plug and pull straight out from outlet. Never unplug by pulling on power cord.
• Do NOT use dispenser if cord becomes frayed or otherwise damaged.
• To protect against electric shock, do NOT immerse cord, plug, or any other part of cooler in water or other
liquids.
• Ensure dispenser is unplugged prior to cleaning.
• Never allow children to dispense hot water without proper and direct supervision. Unplug unit to prevent
unsupervised use by children.
page 7 Assembly drawing

Front Back

Control: Hot Water 1 Bottle Probe 12

Hot Water Release 2 Pump 13
Control: Cook Water 3 Hot Power Switch ( Energy Saving) 14
Control: Cold Water 4 Cold Power Switch ( Energy Saving) 15
Hot Water Tap 5 Heating Power Management Switch 16
Cook Water Tap 6 Fuse 17
Cold Water Tap 7 Power Cord 18
Drip Tray 8 Carry Handle 19
Door 9 Drain Plug 20
Bottle Tray 10 Condenser 21
Door Switch 11
 Explode drawings page 8

8. Explode drawing(s)
8.1 BL with plastic door panel, No display

SHARP MODEL:SWD-82EHL-PB
NO. appellation PN Explode drawing
Bottle receptacle
Floating baffle PP001B063
Baffle stick PP001B013
Evaporator assembly 10200022XX
Top Cover 4X00335BXB
Plastic cold tank body 4X00103PXN-V01
Hot water button assembly 11100244XX
Warm water button 4X00251BXB
flush button 4X00250BXB
Leading the push rod PB001B239
Push-button holder 4X00341BXB
Leading connecting rod PM001B040
Touch the control display board 6M00004D5X
Front insert panel assembly 11000023XX
T fitting nut PP001B142
Seal pad XS001C926
T connector PM001C061
Water faucet 4X00016BCC
Faucet assembly W2050U026
Top panel 4X00338BXB
Hot bile inlet pipe 4X00295SXN00
Hot tank assembly 10300014XX00
Hot bladder exhaust hose XD001C060
Drip tray grill 3S001161XX
Drip tray 4X00340BXB
Compressor shelf AC001C550-1
Door sticker HS002X206
Right side panel 3S39B00001
D 10900016XX00
Plastic door assembly
Probe assembly 10500010NX00
Door hinge plate assembly 3S000013GX
Base plate assembly 11100043XX00
Blue switch of waterproof cover 4X00001BXL
Red switch of waterproof cover 4X00002BXR
Black switch of waterproof cover 6S001SAPXB
Control box cover plate 3S001305XX
Main Controller 6MT0004D7V
Transformer DEAT02P088
Fuse holder assembly 6F0006SSAA00
Cold tank insulation WF001A216
Rear back panel control box 3S5XX00007
Power cord 6WP200F41B
Temperature sensor cold tank 6WA090BX1W
Hot water outlet pipe 4X00028SXN
Cool water inlet pipe 4X00274SXN00
Hot and cold gallbladder connection pipe 4X00014SXN
Top shelf AC001C561-2
Drain T fitting 4X00107PXN
Drain seal XS001C013
Drain fitting cap PP001C122
Compressor assembly 10200001BX
Dry filter 3M000268XX00
Pump outlet extrusion pipe 4X00140SXX01
Water pump holder 4X00005RX000
Water Pump assembly 10800009XX00
Water pump connecting pipe 4X00136SXN02
Condenser ND001A092
left side plate 3S39B00002
page 9 Explode drawings

9. Specifications

Model SWD-82EHL-PB

Description Bottom bottle, Black cabinet

Cool (Cook) Tap Black-Grey cooking pot lcon
Cold Tap Black-Blue Glass lcon
Hot tap (Toddle safety latch) Black-Red Latch/Red Cup Icon
LCD display NO
Ozone sanitizer NO
Features Hot switch Yes,water proof cover
Cold switch Yes,water proof cover

Heating power management switch Yes,water proof cover

Carry Handle Yes

220V 50Hz (Working range:

Rated voltage and range
160V~240V)
Current <3.5A
Power rating Power plug 250V, 10A, 2 pins Euro plug
Main fuse 250V 4A
Heater power 220V/585W +5% -10%
Compressor Power 70W, Max:<100W
Output/Flow Cold water (<10C) Output:4 L/h, Flow:2.2L/min
Hot water (>80C) Output:6 L/h, Flow:1.8L/min
Cook water Output:NA, Flow:2L/min
Cold temperature range 3~10℃
Temperature Cooling thermostat NTC electronic sensor
Hot temperature range 80~92℃
Heating thermostat NTC electronic sensor
Heater Safety Dry burn thermostat 130℃ bimetal, autorest
High temperature fuse 192℃ OFF
 Sanitizing & cleaning, Specifications page 10

Model SWD-82EHL-PB

Pump motor Motor voltage DC12V

Model QD25H
Starter QPS2-A15MG1
Compressor
Protector BB45-125 12J-1
Refrigerant R134A
Top cover ABS-Black
Front Top panel ABS-Black
Front Middle panel NA
Front Middle Insert panel Stainless Steel 430+ABS
Front Bottom panel or Door ABS-Black
0.45mm Steel powder coat -
Side Panels
Black-wrinkle finish
0.6mm Galvanized or powder
Cold tank shelf
coated steel
Compressor middle shelf 0.6mm Galvanized or powder
coated steel
Construction
Base plate ABS - Black
Logo Silk screen print
Tap Markings Molded on insert panel
Storage cabinet NA
Drip Tray ABS-Black
Drip Tray Grill Stainless 430
Wall strap kit for stability NA
Bottle Receptacle NA
Probe Bottom - Easy on probe-SVN:
Expandable
Float assebly Mechanical float valve with
electrodes
Water Reservoir Natural color PP
Dimensions Width x Depth x Height (mm) 382*320*1028
Weight Net weight (kg) 16.0kg
Gross weight (kg)
Material White corrugated paper-color box
Packaging Protection EPS Foam
Packaging
Cover bag material PE
Color Box (±5mm)Width x
360X390X1148
Depth x Height (mm)
Container 20' container 192
Quantity 40' container 396
40'H container 396
page 11 Trouble shooting

10. Trouble shooting

Problems Reasons How to solve Notice

1. Switch doesn’t work 1. Check switch

2. Fuse(s) burnt 2. Check fuse(s)
Hot water is not hot 3. Control board and NTC sensors don’t work 3. Check heater
4. Heater doesn’t work 4. Check control board and NTC
5. Wires are disconnected 5. Check wiring
1.Switch doesn’t work 1.Check switch
2.Fuse burnt 2.Check fuse
Cold water is not 3.Control board and NTC sensor don’t work 3.Check control board and NTC
cold (<10C) 4.Compressor doesn’t work 4.Check compressor
5.Refrigeration sys leaks 5.Check the temperature of condenser, hot
6.Wires are disconnected means refrigeration sys works
6.Check wiring

1.Bottle probe leaks 1. Check O rings of the stick, reinstall the probe
No water come out 2.Water pump doesn’t work assembly
from the taps 3.Control board doesn’t work 2. Check water pump and it’s wire connection
3. Check control board
4.Level switch and float assembly have problem
4. Check level switch and float assembly
1.Check float assembly, check baffle plate
Tap flow is too slow 1.Water level is too low in the water reservoir
inside the water reservoir
(<1.5L/min) 2.Silicone tube is twisted
2.Check silicone tube

Heating noise 1.60 DbA in 2-3 minutes is normal when water starts boiling 1.Use dbmeter check if it is too high
2.Voltage is too high 2.Check voltage is 220V or not.

1.Voltage and frequency are unstable 1.Check voltage and frequency

Cooling noise 2.Condenser or internal parts are not well installed result 2.Hold the condenser by hand, if the noise
resonance disappear, then put rubber pad between
condenser and side panel
1.Check the installation, especially the soft
1.Installation is not good sleeve
Pump noise
2.Probe assembly results bigger noise sometimes 2.Take apart the probe assembly to see if it is
normal, then change a new one.
1.Change new bottled water and clean the
1.Source water may has taste or out of date cooler.
Water has taste 2.Cooler may not be cleaned when first time use or long time 2.Flush the cooler for a few times with boiling
use treatment according to the taste treatment
instruction.
1.Probe or tube leak 1.Check the probe and O rings, then reinstall
2.Magnetic switch or level switch failure 2.Check magnetic switch and level switch
Pump doesn’t work 3.Transformer or Control board don’t work 3.Check transformer(Check if the LED light
4.Wire connection failure work) and control board
5.Water pump doesn’t work 4.Check wire connection
Water pump work 1.Wrong wire connection 1.Check wire connection
continuously 2.Control board doesn’t work 2.Change control board
Change hinge plate or add washer above the
Door gap is too big Door hinge plate distort
hinge shaft
Door gap is not Rectify the corner diagonally according to the
Diagonal distort
even instruction of “How to fix the door gap”
Door can’t be closed 1.Door distort diagonally or the folding edge distort obtusely 1.Rectify the door by hand
tightly 2.Door folding edge distort 2.Rectify the edge by hand
 How to change parts page 12

How to change parts

CAUTION: UNPLUG POWER BEFOREDOING SERVICE

1. Change fuse
1.1 Screw out the fuse cap
1.2 Take out the fuse
1.3 Change a new one and screw on the cap.

2. Change power switch(es)

2.1 Take off the control box by unscrewing 6 bolts
2.2 Pull off the wires to Switch(es) NOTE: The lock on the female terminal need to be pressed down before pull out the wire
connector.
2.3 Take out the switch(es)
2.4 Change new ones
2.5 Plug the wires back
2.6 Check the wire connection then screw on the control box cover

3. Change transformer NOTE: Make sure the static protection is equipped before
doing service to protect control board.
3.1 Take off the control box cover by unscrewing 2 bolts
3.2 Take off the Control board from the plastic standoffs, then take off 2 wires by using iron.
3.3 Pull off 2 wires with connectors to other wires or control board. NOTE: The lock on the female terminal need to be
pressed down before pull out the wire connector.
3.4 Unscrew 2 bolts then take out the transformer
3.5 Change a new one
3.6 Connect wires
3.7 Install the control box cover back
 page 13 How to change parts

4. Change control boards Inside the control box NOTE: Make sure the static
protection is equipped before doing service to protect control board.
4.1 Take off the control box cover by unscrewing 2 bolts
4.2 Pull off all wires on the board
4.3 Take out the control board and change a new one
4.4 Connect the wires back and double check with the wire connection drawing
4.5 Plug in the water dispenser and test if it work properly.
4.6 Install the control box cover back.

5. Change float cover

5.1 Take off the control box cover by unscrewing 2 bolts
5.2 Pull the wires off from the control board by pressing down the lock.
5.3 Open the top cover by unscrewing 2 bolts on the back.
5.4 Take out the float cover by unscrewing 2 bolts, take away the glue.
5.5 Change a new float cover and glue it after installation.
5.6 Connect the wire and do the test before closing the top cover.
5.7 Install the top cover back
5.8 Install the control box cover back.

6. Change drain seal and cap

6.1 Open the door to Stop pumping water
6.2 Unscrew on bolt then take out the drain cap
6.3 Pull out the seal. CAUTION: Water may be hot!
 How to change parts page 14

6.4 Change new seal and cap.

6.5 Close the door.

7. Change hot tank assembly

7.1 Switch off the hot tank and drain out water from the drain cap.
7.2 Open an angle for the condenser by unscrewing 6 bolts on the back.
7.3 Remove the door hinge plate by unscrewing 3 bolts, remove the door rope then remove the door.
7.4 Unscrew the bolts for front panel from the front and back, then take off the front panel.
7.5 Unscrewing 3 bolts out from the front to remove the hot tank assembly
7.6 Pull out 3 silicone tubes from the hot tank. CAUTION : Do not scratch the silicone tubes.
7.7 Pull off the wires by pressing down the locks.
7.8 Change a new hot tank assembly, and connect the wires, then plug back the silicone tubes with a little water as
lubrication. CAUTION: Do not twist the silicone tubes
7.9 Make sure the the hot tank is switched off by switch or the touch panel on the LCD panel then plug in power and
7.10 Press down the door switch by hand and let dispenser pump water into the hot tank.
7.11 Draw water out from the hot tap to check the water flow. And check if there is water leak by hand light.
7.12 Install the front panel back, then condenser and door.

8. Change pump
8.1 Open the door and Pull out the silicone tube.
8.2 Unscrew 4 bolts.
8.3 Change a new pump into the housing.
8.4 Plug in the silicone tube
8.5 Connect the wires and then plug in power, drain a few cups water from the taps, then press down the door switch to see
if it is works.
 page 15 How to change parts

9. Change probe assembly

9.1 Open the door then take out the bottle with probe assembly.
9.2 Unscrew the nut on the probe assembly then pull up the probe assembly.
9.3 Pull out the silicone tube then remove the PE tubes.
9.4 Change a new probe assembly and plug PE tubes on it .
9.5 Pull on the silicone tube then fix the water pipe
9.6 Close the door and test if it works properly.

10. Change water tap buttons

10.1 Remove 2 bolts on the back then take off the top cover by gentle hitting from the back with hand.
10.2 Remove the tap buttons and place the new buttons on the pushers and align with the holes on the top cover.
10.3 Close the top cover and test the tap button to see how do they work then screw on the bolts.

11. Change water taps

11.1 Remove the top cover by unscrewing 2 bolts at back.
11.2 Remove the door hinge plate by unscrewing 3 bolts, remove the door rope then remove the door.
11.3 Take off the top front panel by unscrewing 2 bolts. NOTE: The top front panel has wires connect with the
dispenser, hang it on the dispenser properly to avoid damage of wires.
11.4 Take out the water tap by tipping over unclockwisely.
11.5 Pull off the silicone tubes.
11.6 Connect the silicone tubes into the new taps with water as lubrication. CAUTION: Do not twist the tubes.
 How to change parts page 16

11.7 Check the tubes make sure no twisting then Press down the new water taps into the grooves firmly.
11.8 Install the top front panel back, then connect the tap pusher and tap stick in place. CAUTION: Do not forget to install
the tap pusher and tap stick!
11.9 Install the door back.

12. Change top cover

12.1 Remove 2 bolts on the back then take off the top cover by gentle hitting from the back with hand (there are 2 hooks at
the front).
12.2 Change a new top cover,.
12.3 Press down the top cover in place, then screw on 2 bolts from the back.

13. Change top front panel assembly

13.1 Remove 2 bolts on the back then take off the top cover by gentle hitting from the back with hand(there are 2 hooks at
the front).
13.2 Remove the door hinge plate by unscrewing 3 bolts, remove the door rope then remove the door.
13.3 FOR MODEL WITHOUT DISPLAY: Unscrewing 2 bolts of the front top panel, then take off the panel gently.
CAUTION: there is wire connect between the top front panel and water dispenser.
13.4 Insert the hooks of the new top front panel assembly into the holes on the side panel, then screw on the bolts on the
top.
13.5 Connect the tap pusher and tap stick in place.
13.6 Install the top cover, front panel and door back.
 page 17 How to change parts

14. Change door assembly

14.1 Take off the door rope by unscrewing one bolt on the door.
14.2 Remove the door hinge plate by unscrewing 3 bolts.
14.3 Take away the door together with the hinge plate.
14.4 Plug the door shaft and hinge plate into the new door.
14.5 Install the new door together with shaft and hinge plate,
then screw on the bolt for door rope.
14.6 Close the door check the gaps and if it works properly.

15. Change LED PCB panel

15.1 Remove the insert panel.
15.2 Pull off the LED wire connector by pressing the lock.
15.3 Unscrew 2 bolts and take out the LED PCB assembly then change a new one.

16. Change insert panel (with LED)

16.1 Remove the insert panel the hooks at the bottom.
16.2 Take the insert panel panel out gently.
16.3 Pull off the LED wire connector by pressing the lock.
16.4 Unscrew 2 bolts and take out the LED PCB assembly .
16.5 To change insert panel: install the control board in place by hooks first with static protection equipments, then plug all
the wire connectors.
16.6 Insert 2 hooks of the insert panel to the Top front panel on the top first, then press down, the lower hooks will be
clicked in at the bottom.

17. Change hot tank silicone tubes

17.1 Open the condenser by unscrewing 6 bolts from the back.
17.2 Drain water out from the drain cap. CAUTION: water maybe hot!
17.3 Take off the silicone tubes from the hot tank and plastic fittings.
17.4 Change new silicone tube and check if they are twisted.
17.5 Plug in power and pump water into hot tank to see if there is leaking.
17.6 Install the condenser with 6 bolts.
 How to change parts page 18

18. Change hot tank temp sensor

18.1 Open the condenser by unscrewing 6 bolts.
18.2 Remove the door together with the hinge plate.
18.3 Remove the middle panel.
18.4 Unplug the wire connectors and silicone tubes from the hot tank.
18.5 Take off the hot tank assembly by unscrewing out 3 bolts.
18.6 Take off the thermostat cover on the side and on the bottom of the hot tank.
18.7 Check the thermostat and change new ones. Use thermostat holder to fix the thermostat when bolting on the new
thermostat on the side.
18.8 Install the thermostat cover(s) back.
18.9 Plug the silicone tube and wires back.
18.10 Install all the panels and condenser back.

19. How to Connect / disconnect the quick connector and tubes

19.1 Take out the fork。
19.2 Press down the collet then pull the tube out。
19.3 Cut a chamfer by pencil sharpener at the end of the PE tube before
page 19 How to change parts