MITER AND BEVEL GEARS

SECTION CONTENTS

CATALOG NUMBER / DIMENSIONS

MITER GEAR ........................................................................................................................... 58 – 60

SPIRAL MITER GEAR ...................................................................................................................... 61

BEVEL GEAR............................................................................................................................ 62 – 65

SPIRAL BEVEL GEAR ..................................................................................................................... 66

SELECTION PROCEDURE .......................................................................................................................67

HORSEPOWER AND TORQUE RATINGS

MITER GEAR ........................................................................................................................... 68 – 69

BEVEL GEAR.................................................................................................................................... 70

SPIRAL MITER GEAR ...................................................................................................................... 71

SPIRAL BEVEL GEAR ..................................................................................................................... 71

STOCK ALTERED / CUSTOM MITER AND BEVEL GEARS .......................................................... 87 – 89

MITER / BEVEL GEAR ENGINEERING INFORMATION............................................................. 145 – 147

Gear Catalog 57
 MITER GEARS
48 THROUGH 20 DIAMETRAL PITCH 1:1 RATIO 20° PRESSURE ANGLE
NYLON, BRASS, STAINLESS STEEL AND STEEL—UNHARDENED

All gears have “Coniflex”® tooth form, except as noted.

MOUNTING
DISTANCE

FACE
PITCH
DIA.

HUB
BORE PROJ.
HUB
DIA.

REFERENCE PAGES STANDARD TOLERANCES*

Alterations — 151 DIMENSION TOLERANCE
Lubrication — 151 BORE All ±.0005
Materials — 152
*Brass and Steel only.

ALL DIMENSIONS IN INCHES

ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item Catalog Item Catalog Item
Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code Number Code Number Code
48 MOLDED STAINLESS STEEL
DIAMETRAL PITCH NYLON BRASS STEEL UNHARDENED
15 .312 .07 .125 .312 .215 .25 .13 GP4815†‡ 54096 G460Y† 12126 GSS460Y† 49984 — —
.33 .19 GP4818Y† 54097 — — — — — —
18 .375 .08 .125 .406 .286 .31 .16 — — G461Y† 12128 GSS461Y† 49985 L94Y† 12140
24 .500 .08 .1875 .531 .375 .38 .25 GP4824Y† 54098 — — — — — —
32
DIAMETRAL PITCH
16 .500 .12 .1875 .500 .349 .41 .19 GP3216Y† 54099 G462Y† 12114 GSS462Y† 49986 L97Y† 12146
.406 .50 .19 GP3224Y† 54100 — — — — — —
24 .750 .14 .1875 .688 .427 .50 .25 — — G463Y† 12116 GSS461Y† 49987 L95Y† 12142
30
DIAMETRAL PITCH
15 .500 .12 .1875 .500 .349 .41 .19 — — — — — — L93Y 12138
24
DIAMETRAL PITCH
.19 GP2424Y† 54101 — — — — — —
24 1.000 .20 .250 .906 .567 .62
.28 — — G464Y 12100 — — L96Y 12144
30 1.250 .23 .250 1.031 .590 .62 .31 GP2430Y† 54102 G465Y 12102 — — — —
36 1.500 .23 .3125 1.188 .620 .69 .31 GP2436Y† 54103 G466Y 12104 — — — —
20
DIAMETRAL PITCH
12 .600 .13 .250 .672 .489 .50 .31 — — — — — — L98Y 12148

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.
†Not “Coniflex” tooth form. Can be furnished with “Coniflex” tooth on special order.
‡Acetal.

58 Gear Catalog
 MITER GEARS
16 THROUGH 10 DIAMETRAL PITCH 1:1 RATIO 20° PRESSURE ANGLE
NYLON AND STEEL—UNHARDENED AND HARDENED

All gears have “Coniflex”® tooth form, except as noted.

All hardened steel gears have teeth only hardened, except as
noted, and are equipped with standard keyways and setscrews

MOUNTING
DISTANCE
KEYWAY
FACE
PITCH
DIA.

D
SETSCREW
HUB
BORE PROJ.
HUB
DIA.
REFERENCE PAGES
Alterations — 151 STANDARD TOLERANCES*
Horsepower Ratings — 68, 69 DIMENSION TOLERANCE
Lubrication — 151 BORE All ±.0005
Materials — 152
Selection Procedure — 67 *Steel only.

ALL DIMENSIONS IN INCHES NO KEYWAY

ORDER BY CATALOG NUMBER OR ITEM CODE OR SETSCREW
No. of Pitch MD Hub Catalog Item Catalog Item Catalog Item
Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code Number Code
16 MOLDED STEEL STEEL
DIAMETRAL PITCH NYLON UNHARDENED HARDENED
12 .750 .16 .3125 .812 .583 .62 .38 — — L99Y 12150 — —
16 1.000 .23 .375 1.062 .755 .75 .44 GP1616Y† 54104 L110Y 12174 HLK110Y** 12326
20 1.250 .28 .4375 1.250 .849 1.00 .50 — — L111Y 12176 — —
24 1.500 .32 .500 1.375 .880 1.00 .50 — — L112Y 12156 — —
32 2.000 .39 .500 1.562 .875 1.25 .38 GP1632Y†‡ 54105 — — — —
14
DIAMETRAL PITCH
.375 — — L124Y 12202 — —
14 1.000 .20 .4375 1.062 .739 .88 .50 — — L100Y 12152 — —
12
DIAMETRAL PITCH
.375 — — L125Y 12204 — —
15 1.250 .29 .4375 1.250 .864 1.00 .50 — — L126Y 12206 — —
.500 — — L101Y 12154 HLK101Y** 12328
.500 — — L127Y 12208 — —
18 1.500 .33 1.500 1.021 1.25 .63
.625 — — L102Y 12158 HLK102Y 12330
.500 — — L119Y 12190 — —
.5625 — — L120Y 12192 — —
21 1.750 .40 1.750 1.192 1.38 .69
.625 — — L121Y 12194 HLK121Y 12334
.750 — — L133Y 12218 — —
24 2.000 .44 .500 1.875 1.224 1.31 .69 — — L113Y 12178 — —
30 2.500 .55 .625 2.312 1.489 1.62 .84 — — L114Y 12180 HLK114Y 12332
10
DIAMETRAL PITCH
.500 — — L128Y 12210 — —
20 2.000 .45 .625 2.000 1.364 1.62 .81 — — L129Y 12212 HLK129Y 12348
.750 — — L103Y 12160 HLK103Y 12344
.750 — — L130Y 12214 HLK130Y 12350
25 2.500 .56 .875 2.438 1.630 2.00 .94 — — L104Y 12162 HLK104Y 12346
1.000 — — L131Y 12216 HLK131Y 12352

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.
†Not “Coniflex” tooth form.
**Hardened all over.
‡Nylon (Mineral Filled).

Gear Catalog 59
 MITER GEARS
8 THROUGH 4 DIAMETRAL PITCH 1:1 RATIO 20° PRESSURE ANGLE
STEEL—UNHARDENED AND HARDENED AND CAST IRON

All gears have “Coniflex”® tooth form, except as noted.

All hardened steel gears have teeth only hardened, except as
noted, and are equipped with standard keyways and setscrews.
All unhardened steel gears have no keyway and no setscrew.

MOUNTING
DISTANCE
KEYWAY
FACE
PITCH
DIA.

D
SETSCREW
HUB
BORE PROJ.
HUB
REFERENCE PAGES DIA.
Alterations — 151
Horsepower Ratings — 68, 69 STANDARD TOLERANCES
Lubrication — 151 DIMENSION TOLERANCE
Materials — 152 BORE All ±.0005
Selection Procedure — 67
ALL DIMENSIONS IN INCHES
ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item Catalog Item
Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code Number Code
8 STEEL STEEL
DIAMETRAL PITCH UNHARDENED HARDENED CAST IRON
.66 .750 2.562 1.583 1.75 .81 L115Y 12182 HLK115Y 12366 — —
24 3.000 .68 1.000 L105Y-A 12164 HLK105YA 12362 — —
1.250 2.750 1.786 2.50 1.00 L116Y 12184 HLK116Y 12368 — —
1.000 L117Y 12186 HLK117Y 12370 — —
.77 1.1875 3.250 2.099 2.50 1.25 L132Y 12196 HLK132Y 12374 — —
28 3.500 1.250 L106Y 12166 HLK106Y 12364 — —
.77 .875 2.875 1.724 2.00 .88 — — — — OA828Y-1 12418
.85 1.000 3.625 2.286 3.00 1.13 L123Y 12200 HLK123Y 12372 — —
32 4.000
.85 .875 3.438 2.098 2.25 1.12 — — — — OA832Y-1 12420
6
DIAMETRAL PITCH
1.250 L118Y 12188 HLK118Y 12386 OA624Y† 12412
24 4.000 .87 3.625 2.317 3.00 1.31
1.500 L107Y 12168 HLK107Y 12384 — —
1.250 L134Y 12220 — — — —
27 4.500 .96 4.125 2.630 3.25 1.50
1.500 L135Y 12222 — — — —
30 5.000 1.16 1.000 4.250 2.640 2.50 1.38 — — — — OA630Y-1 12414
36 6.000 1.28 1.125 4.625 2.605 2.88 1.19 — — — — OA636Y-1 12416
5
DIAMETRAL PITCH
1.375 L122Y 12198 HLK122Y 12398 — —
25 5.000 1.12 1.500 4.625 3.005 3.50 1.75 L136Y 12224 — — OA525Y 12408
1.750 L108Y 12170 HLK108Y 12396 — —
40 8.000 1.50 1.375 5.500 2.660 3.75 1.00 — — — — OA540Y-1 12410
4
DIAMETRAL PITCH
1.500 L137Y 12226 — — — —
24 6.000 1.35 5.500 3.567 4.00 1.94
1.750 L109Y 12172 HLK109Y 12404 OA424Y** 12406
28 7.000 1.43 2.000 6.000 3.630 5.00 1.94 L138Y 12228 — — — —

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.
†Hub Dia. — 2.750"
**Hub Proj. — 2.000"

60 Gear Catalog
 SPIRAL MITER GEARS
18 THROUGH 5 DIAMETRAL PITCH 1:1 RATIO 20° PRESSURE ANGLE
STEEL—UNHARDENED AND HARDENED 35° SPIRAL ANGLE

All hardened steel gears have teeth only hardened, except as

noted, and are equipped with standard keyways and setscrews

MOUNTING
DISTANCE

FACE
PITCH
DIA.

HUB
BORE PROJ.
HUB
DIA.

REFERENCE PAGES STANDARD TOLERANCES

Alterations — 151 DIMENSION TOLERANCE
Horsepower Ratings — 71 BORE All ±.0005
Lubrication — 151
Materials — 152
Selection Procedure — 67
ALL DIMENSIONS IN INCHES
ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item
Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code
18 STEEL STEEL
DIAMETRAL PITCH UNHARDENED HARDENED
LSA110Y-R 12310 HLSK110Y-R† 12322
18 1.000 .22 .375 1.062 .739 .75 .44 LSA110Y-L 12312 HLSK110Y-L† 12324
12
DIAMETRAL PITCH
LSA101Y-R 12282 HLSK101Y-R† 12336
15 1.250 .30 .500 1.250 .864 1.00 .50 LSA101Y-L 12284 HLSK101Y-L† 12338
LSA102Y-R 12286 HLSK102Y-R 12340
18 1.500 .34 .625 1.500 1.021 1.25 .56 LSA102Y-L 12288 HLSK102Y-L 12342
10
DIAMETRAL PITCH
LSA103Y-R 12290 HLSK103Y-R 12354
20 2.000 .47 .750 2.000 1.364 1.62 .78 LSA103Y-L 12292 HLSK103Y-L 12356
LSA104Y-R 12294 HLSK104Y-R 12358
25 2.500 .58 .875 2.438 1.630 2.00 .91 LSA104Y-L 12296 HLSK104Y-L 12360
8
DIAMETRAL PITCH
LSA106Y-R 12302 HLSK106Y-R 12376
28 3.500 .78 1.1875 3.250 2.099 2.50 1.25 LSA106Y-L 12304 HLSK106Y-L 12378
7
DIAMETRAL PITCH
LSA105YA-R 12298 HLSK105YA-R 12380
21 3.000 .69 1.000 2.750 1.786 2.50 .88 LSA105YA-L 12300 HLSK105YA-L 12382
6
DIAMETRAL PITCH
LSA118Y-R 12314 HLSK118Y-R 12392
1.250 LSA118Y-L 12316 HLSK118Y-L 12394
24 4.000 .89 3.625 2.317 3.00 1.31 LSA107Y-R 12306 HLSK107Y-R 12388
1.500 LSA107Y-L 12308 HLSK107Y-L 12390
5
DIAMETRAL PITCH
LSA122Y-R 12318 HLSK122Y-R 12400
25 5.000 1.15 1.375 4.625 3.005 3.50 1.75 LSA122Y-L 12320 HLSK122Y-L 12402

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.
†Hardened all over.

Gear Catalog 61
 BEVEL GEARS
48 THROUGH 20 DIAMETRAL PITCH 20° PRESSURE ANGLE
BRASS AND STAINLESS STEEL AND STEEL —
HARDENED AND UNHARDENED
All gears have “Coniflex”® tooth form, except as noted. All
hardened steel gears have teeth only hardened and are
equipped with standard keyways and setscrews, except as
noted.
MOUNTING
DISTANCE
KEYWAY
D
FACE
PITCH
DIA.
MOUNTING
D DISTANCE

BORE
HUB
SETSCREW DIA. HUB
PITCH PROJ.
DIA.
REFERENCE PAGES
Alterations — 151
Lubrication — 151 STANDARD TOLERANCES
Materials — 152 DIMENSION TOLERANCE
BORE All ±.0005

ALL DIMENSIONS IN INCHES

ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item
Ratio Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code
48 STAINLESS
DIAMETRAL PITCH BRASS STEEL
36 .750 .1875 .438 .257 .44 .19 G479Y-G† 12136 GSS479Y-G† 49991
2:1 .12
18 .375 .125 .594 .335 .28 .19 G479Y-P† 12134 GSS479Y-P† 49990
36 .750 .1875 .375 .257 .44 .19 G478Y-G† 12132 GSS478Y-G† 49989
3:1 .09
12 .250 .125 .562 .285 .22 .17 G478Y-P† 12130 GSS478Y-P† 49988
32
DIAMETRAL PITCH
32 1.000 .594 .382 .56 .25 G481Y-G† 12120 GSS481Y-G† 49993
2:1 .14 .1875
16 .500 .719 .365 .38 .17 G481Y-P† 12118 GSS481Y-P† 49992
64 2.000 .3125 .688 .445 1.00 .31 G486Y-G† 12108 GSS486Y-G† 49995
4:1 .24
16 .500 .1875 1.250 .500 .38 .22 G486Y-P† 12106 GSS486Y-P† 49994
24
DIAMETRAL PITCH
36 1.500 .250 .781 .460 .88 .31 G485Y-G 12124 — —
.24
18 .750 .1875 1.062 .540 .56 .25 G485Y-P 12122 — —
2:1
48 2.000 .3125 .938 .507 1.12 .31 G487Y-G 12112 — —
.26
24 1.000 .250 1.375 .630 .69 .28 G487Y-P 12110 — —
20 STEEL STEEL
DIAMETRAL PITCH UNHARDENED HARDENED
20 1.000 .375 .688 .460 .75 .31 L147Y-G 12234 — —
.18
10 .500 .1875 .750 .425 .41 .25 L147Y-P 12236 — —
2:1
20 1.000 .375 .688 .460 .75 .31 — — HL147Y-G‡ 11854
.18
10 .500 .1875 .750 .425 .41 .25 — — HL147Y-P‡ 11856

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.
†Not “Coniflex” tooth form. Can be furnished with “Coniflex” tooth on special order.
‡These gears have No. 47 (.0785) drilled hole in hub. No keyway or setscrew.

62 Gear Catalog
 BEVEL GEARS
16 THROUGH 12 DIAMETRAL PITCH 20° PRESSURE ANGLE
STEEL—UNHARDENED AND HARDENED
AND CAST IRON
All gears have “Coniflex”® tooth form.
All Hardened steel gears have teeth only hardened and are
equipped with standard keyways and setscrews.
MOUNTING
DISTANCE
D
FACE
PITCH
DIA.
MOUNTING
D DISTANCE

BORE
HUB
DIA. HUB
PITCH PROJ.
DIA.

REFERENCE PAGES
Alterations — 151
Horsepower Ratings — 70 STANDARD TOLERANCES
Lubrication — 151 DIMENSION TOLERANCE
Materials — 152 BORE All ±.0005
Selection Procedure — 67
ALL DIMENSIONS IN INCHES
ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item Catalog Item
Ratio Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code Number Code
16 STEEL STEEL CAST IRON GEARS
DIAMETRAL PITCH UNHARDENED HARDENED STEEL PINIONS
24 1.500 .500 1.188 .760 1.12 .56 L146Y-G 12230 — — — —
16 1.000 .26 .375 1.250 .740 .81 .44 L146Y-P 12232 — — — —
1-1/2:1
24 1.500 .500 1.188 .750 1.12 .56 — — HL146Y-G 11850 — —
.26
16 1.000 .375 1.250 .740 .81 .44 — — HL146Y-P 11852 — —
24 1.500 .20 .500 1.000 .625 1.00 .44 L148Y-G 12238 HL148Y-G 11858 — —
12 .750 .19 .375 1.125 .575 .66 .34 L148Y-P 12240 HL148Y-P 11860 — —
2:1
32 2.000 .500 1.188 .775 1.12 .50 L149Y-G 12242 HL149Y-G 11862 — —
.36
16 1.000 .375 1.500 .845 .81 .44 L149Y-P 12244 HL149Y-P 11864 — —
48 3.000 .625 1.312 .882 1.50 .56 — — — — PA3316Y-G 12484
3:1 16 1.000 .42 .4375 2.000 .920 .88 .47 — — — — PA3316Y-P 12486
64 4.000 .625 1.375 .898 2.25 .56 — — — — PA4416Y-G 12492
4:1 .49
16 1.000 .500 2.500 .990 .81 .47 — — — — PA4416Y-P 12494
96 6.000 .625 1.688 1.257 1.75 .88 — — — — PA6616Y-G 12516
6:1 .62
16 1.000 .500 3.750 1.375 .94 .72 — — — — PA6616Y-P 12518
14
DIAMETRAL PITCH
28 2.000 .36 .500 1.375 .945 1.62 .66 L150Y-G 12246 HL150Y-G 11866 — —
2:1 .375 — — HL150Y-P 11868 — —
14 1.000 .35 1.625 .965 .81 .56
.500 L150Y-P 12248 — — — —
12
DIAMETRAL PITCH
.500 L151Y-G 12250 — — — —
27 2.250 .42 1.750 1.135 1.50 .78
1-1/2:1 .750 — — HL151Y-G 11870 — —
18 1.500 .41 .500 1.875 1.130 1.25 .66 L151Y-P 12254 HL151Y-P 11872 — —
36 3.000 .54 .625 1.875 1.275 2.12 .88 L152BY-G 12260 — — — —
18 1.500 .54 .500 2.375 1.385 1.31 .81 L152BY-P 12262 — — — —
2:1 36 3.000 .54 1.000 1.875 1.275 2.12 .88 L152Y-G 12256 HL152Y-G 11874 — —
.625 — — HL152Y-P 11876 — —
18 1.500 .53 2.375 1.375 1.31 .81
.750 L152Y-P 12258 — — — —

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.

Continued next page

Gear Catalog 63
 BEVEL GEARS
12 AND 10 DIAMETRAL PITCH 20° PRESSURE ANGLE
STEEL—UNHARDENED AND HARDENED
AND CAST IRON
All gears have “Coniflex”® tooth form.
All Hardened steel gears have teeth only hardened and are
equipped with standard keyways and setscrews.
MOUNTING
DISTANCE
D
FACE
PITCH
DIA.
MOUNTING
D DISTANCE

BORE
HUB
DIA. HUB
PITCH PROJ.
DIA.

REFERENCE PAGES
Alterations — 151
Horsepower Ratings — 70 STANDARD TOLERANCES
Lubrication — 151 DIMENSION TOLERANCE
Materials — 152 BORE All ±.0005
Selection Procedure — 67
ALL DIMENSIONS IN INCHES
ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item Catalog Item
Ratio Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code Number Code
12 STEEL STEEL CAST IRON GEARS
DIAMETRAL PITCH UNHARDENED HARDENED STEEL PINIONS
36 3.000 .625 1.500 .882 1.44 .50 — — — — PA3212Y-G 12480
.47
18 1.500 .500 2.250 1.205 1.25 .69 — — — — PA3212Y-P 12482
2:1
48 4.000 .625 2.000 1.180 1.63 — — — — PA4212Y-G 12488
.59 .75
24 2.000 .500 2.875 1.440 1.50 — — — — PA4212Y-P 12490
54 4.500 .625 1.750 1.063 1.75 .75 — — — — PA45312Y-G 12532
3:1 .60
18 1.500 .500 3.000 1.350 1.25 .69 — — — — PA45312Y-P 12534
72 6.000 .750 2.000 1.320 2.00 .95 — — — — PA6412Y-G 12508
4:1 .61
18 1.500 .500 3.750 1.365 1.25 .72 — — — — PA6412Y-P 12510
72 6.000 .750 1.750 1.320 2.00 .95 — — — — PA6612Y-G 12512
6:1 12 1.000 .74 .500 3.750 1.495 .94 .72 — — — — PA6612Y-P 12514
10
DIAMETRAL PITCH
.750 L153Y-G 12264 — — — —
30 3.000 .58 2.250 1.445 2.50 1.00
1 1/2:1 1.000 — — HL153Y-G 11878 — —
20 2.000 .58 .750 2.500 1.525 1.75 .91 L153Y-P 12266 HL153Y-P 11880 — —
40 4.000 .875 2.500 1.695 3.00 1.19 L155Y-G 12268 — — — —
.72
20 2.000 .750 3.125 1.805 1.75 1.06 L155Y-P 12270 — — — —
40 4.000 1.250 2.500 1.695 3.00 1.19 — — HL155Y-G 11882 — —
2:1 .72
20 2.000 .875 3.125 1.805 1.75 1.06 — — HL155Y-P 11884 — —
50 5.000 2.625 1.600 2.00 1.00 — — — — PA5210Y-G 12496
.71 .750
25 2.500 3.375 1.555 2.00 .75 — — — — PA5210Y-P 12498
60 6.000 1.000 2.750 1.865 3.00 1.38 L157Y-G 12274 — — — —
.79
20 2.000 .875 4.375 2.155 1.75 1.31 L157Y-P 12276 — — — —
3:1
60 6.000 .875 2.750 1.913 3.00 1.38 — — — — PA6310Y-G 12500
.79
20 2.000 .750 4.375 2.155 1.75 1.31 — — — — PA6310Y-P 12502
60 6.000 .875 2.250 1.632 2.50 1.13 — — — — PA6410Y-G 12504
4:1 .73
15 1.500 .625 3.875 1.610 1.44 .84 — — — — PA6410Y-P 12506
90 9.000 1.000 2.500 1.820 2.75 1.31 — — — — PA9610Y-G 12524
6:1 .86
15 1.500 .625 5.500 1.870 1.44 .97 — — — — PA9610Y-P 12526

*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.

64 Gear Catalog
 BEVEL GEARS
8 THROUGH 4 DIAMETRAL PITCH 20° PRESSURE ANGLE
STEEL—UNHARDENED AND HARDENED
AND CAST IRON
All gears have “Coniflex”® tooth form.
All Hardened steel gears have teeth only hardened and are
equipped with standard keyways and setscrews.
MOUNTING
DISTANCE
KEYWAY
D
FACE
PITCH
DIA.
MOUNTING
D DISTANCE

BORE
HUB
SETSCREW DIA. HUB
PITCH PROJ.
DIA.

REFERENCE PAGES
Alterations — 151
Horsepower Ratings — 70 STANDARD TOLERANCES
Lubrication — 151 DIMENSION TOLERANCE
Materials — 152
BORE All ±.0005
Selection Procedure — 67
ALL DIMENSIONS IN INCHES
ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item Catalog Item
Ratio Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code Number Code
8 STEEL STEEL CAST IRON GEARS
DIAMETRAL PITCH UNHARDENED HARDENED STEEL PINIONS
1.000 L156Y-G 12252 — — — —
40 5.000 .83 2.875 1.850 3.00 1.25
1.500 — — HL156Y-G 11886 — —
2:1 20 2.500 .83 1.000 4.000 2.290 2.12 1.41 L156Y-P 12272 HL156Y-P 11888 — —
40 5.000 1.000 2.875 1.850 3.00 1.25 — — — — PA528Y-G 12424
.83
20 2.500 .875 4.000 2.290 2.12 1.41 — — — — PA528Y-P 12426
48 6.000 .875 2.375 1.632 2.75 1.00 — — — — PA638Y-G 12436
3:1 16 2.000 .84 .750 4.250 2.085 1.75 1.19 — — — — PA638Y-P 12438
64 8.000 1.000 2.750 1.882 2.75 1.25 — — — — PA848Y-G 12452
.85
16 2.000 .875 5.250 2.105 1.88 1.22 — — — — PA848Y-P 12454
4:1
72 9.000 1.125 3.250 2.320 3.00 1.69 — — — — PA948Y-G 12460
1.23
18 2.250 .875 5.750 2.470 2.13 1.22 — — — — PA948Y-P 12462
6
DIAMETRAL PITCH
36 6.000 1.07 3.500 2.260 3.25 1.50 L158Y-G 12278 — — — —
1.125
18 3.000 1.06 4.750 2.765 2.50 1.59 L158Y-P 12280 — — — —
36 6.000 1.07 1.750 3.500 2.260 3.25 1.50 — — HL158Y-G 11890 — —
18 3.000 1.06 1.125 4.750 2.765 2.50 1.59 — — HL158Y-P 11892 — —
36 6.000 1.125 3.500 2.260 3.25 1.50 — — — — PA626Y-G 12432
2:1 1.07
18 3.000 1.000 4.750 2.765 2.50 1.59 — — — — PA626Y-P 12434
42 7.000 1.125 3.750 2.305 3.50 1.50 — — — — PA726Y-G 12440
1.06
21 3.500 1.000 5.000 2.515 2.50 1.25 — — — — PA726Y-P 12442
48 8.000 1.125 3.438 1.898 3.25 1.00 — — — — PA826Y-G 12448
1.18
24 4.000 1.000 5.438 2.560 2.62 1.25 — — — — PA826-Y-P 12450
45 7.500 1.125 3.000 2.132 3.25 1.25 — — — — PA7536Y-G 12520
3:1 1.08
15 2.500 .875 5.250 2.575 2.12 1.44 — — — — PA7536Y-P 12522
5
DIAMETRAL PITCH
30 6.000 1.125 3.500 2.257 3.25 1.38 — — — — PA625Y-G 12428
2:1 15 3.000 1.05 1.000 4.375 2.390 2.62 1.28 — — — — PA625Y-P 12430
45 9.000 1.250 3.750 2.507 3.75 1.69 — — — — PA935Y-G 12456
3:1 1.32
15 3.000 1.000 5.875 2.685 2.62 1.31 — — — — PA935Y-P 12458
4
DIAMETRAL PITCH
32 8.000 1.125 4.250 2.695 3.75 1.56 — — — — PA824Y-G 12444
2:1 1.40
16 4.000 1.125 6.000 3.350 3.25 1.81 — — — — PA824Y-P 12446
*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.

Gear Catalog 65
 SPIRAL BEVEL GEARS
30 THROUGH 8 DIAMETRAL PITCH 20° PRESSURE ANGLE
STEEL—UNHARDENED AND HARDENED 35° SPIRAL ANGLE

All Hardened steel gears have teeth only hardened and are
equipped with standard keyways and setscrews, except as
noted. All pinions are left hand.
MOUNTING
DISTANCE
D
FACE
PITCH
DIA.
MOUNTING
D DISTANCE

BORE
HUB
DIA. HUB
PITCH PROJ.
DIA.

REFERENCE PAGES
Alterations — 151 STANDARD TOLERANCES
Horsepower Ratings — 71 DIMENSION TOLERANCE
Lubrication — 151
Materials — 152 BORE All ±.0005
Selection Procedure — 67 ALL DIMENSIONS IN INCHES
ORDER BY CATALOG NUMBER OR ITEM CODE
No. of Pitch MD Hub Catalog Item Catalog Item
Ratio Teeth Dia. Face Bore * D Dia. Proj. Number Code Number Code
30 STEEL STEEL
DIAMETRAL PITCH UNHARDENED HARDENED
26 .87 .250 .688 .480 .75 .38 SS302-G 11938 — —
13 .43 .14 .1875 .750 .453 .38 .30 SS302-P 11940 — —
2:1
26 .87 .375 .688 .480 .75 .38 — — SH302-G 11914
.14
13 .43 .1875 .750 .453 .38 .30 — — SH302-P† 11916
19
DIAMETRAL PITCH
26 1.37 .500 1.000 .730 1.12 .42 SS192-G 11934 — —
.25
13 .68 .3125 1.062 .623 .62 .33 SS192-P 11936 — —
2:1
26 1.37 .625 1.000 .730 1.12 .42 — — SH192-G 11910
.25
13 .68 .3125 1.062 .623 .62 .33 — — SH192-P† 11912
14
DIAMETRAL PITCH
26 1.86 .625 1.188 .760 1.38 .50 SS142-G 11926 — —
.31
13 .93 .4375 1.250 .625 .81 .30 SS142-P 11928 — —
26 1.86 .750 1.188 .760 1.38 .50 — — SH142-G 11902
13 .93 .31 .4375 1.250 .625 .81 .30 — — SH142-P 11904
2:1
32 2.29 .750 1.375 .855 1.62 .56 SS142-1G 11930 — —
.38
16 1.14 .500 1.625 .848 1.00 .45 SS142-1P 11932 — —
32 2.29 .875 1.375 .855 1.62 .56 — — SH142-1G 11906
.38
16 1.14 .500 1.625 .848 1.00 .45 — — SH142-1P 11908
10
DIAMETRAL PITCH
34 3.40 1.000 1.875 1.135 2.00 .75 SS102-G 11922 — —
.57
17 1.70 .625 2.375 1.219 1.50 .63 SS102-P 11924 — —
2:1
34 3.40 1.1875 1.875 1.135 2.00 .75 — — SH102-G 11898
.57
17 1.70 .625 2.375 1.219 1.50 .63 — — SH102-P 11900
8
DIAMETRAL PITCH
34 4.250 1.250 2.500 1.575 2.88 1.06 SS82-G 11918 — —
17 2.125 .71 .750 3.125 1.677 1.88 .94 SS82-P 11920 — —
2:1
34 4.250 1.500 2.500 1.575 2.88 1.06 — — SH82-G 11894
.71
17 2.125 .750 3.125 1.677 1.88 .94 — — SH82-P 11896
*Mounting Distance (MD) must not be made less than dimension shown, see Page 146.
†No keyway or setscrew.

66 Gear Catalog
 MITER AND BEVEL GEARS
Boston stock miter and bevel gears are designed for transmission of power
and/or motion between intersecting shafts at a right angle (90°). Miter gears are
a special type of bevel gear designed to operate as pairs being identical in num-
ber of teeth and pitch (1 to 1 ratio only). Other Boston stock bevel gear sets are
available with ratios from 1-1/2:1 to 6:1.
All Boston standard stock bevels and miters are manufactured with a 20° pres-
sure angle. These bevel gears are made in accordance with AGMA specifica-
tions for a long and short addendum system for gears and pinions, which serves
to reduce the amount of pinion tooth undercut and to nearly equalize the strength
and durability of the gear and pinion. Boston straight tooth bevel and miter gears
have generated teeth with “Coniflex”® tooth form, unless otherwise specified.

INTERCHANGE
Stock miter and bevel gears having identical diametral pitch, number of teeth
and mounting distance (and spiral angle for spiral bevels) are interchangeable.

SPIRAL VS. STRAIGHT TOOTH

Boston standard stock straight bevel gears can be used for all applications
requiring transmission of power and motion between intersecting shafts. Boston
standard stock spiral bevel gears have an overlapping tooth action which results
in a smoother gear action, lower noise, and higher load capacity than a straight
bevel of equal size.
®Trademark of the Gleason Works.

SELECTION PROCEDURE
Approximate horsepower ratings for selected sizes (number of 1. Determine service factor.
teeth) at various operating speeds (RPM) are given for Boston a. Using Application Classification Chart I, pages 154–155
standard stock Bevel and Miter gears. determine service factor or
For straight tooth Miter gears, refer to Pages 68, 69. b. With knowledge of operating conditions and load classi-
For straight tooth Bevel gears, refer to Page 70. fication, select service factor from Table 1.
For spiral tooth Miter gears, refer to Page 71. 2. Determine Design Horsepower.
For spiral tooth Bevel gears, refer to Page 71. Design HP = Application Load x Service Factor (Table 1)
All ratings are based on normal operating conditions, that is: 3. Select a gear set with horsepower capacity equal to (or
properly mounted and lubricated, carrying a smooth load for greater than) design horsepower determined in Step 2.
not more than 10 hours (Service Factor = 1.0). Refer to Table 1
for service factors in other service conditions.

TABLE 1
Service
Factor Operating Conditions
.8 Uniform — not more than 15 minutes in 2 hours.
Moderate Shock — not more than 15 minutes in 2 hours.
1.0
Uniform — not more than 10 hours per day.
Moderate Shock — not more than 10 hours per day.
1.25
Uniform — more than 10 hours per day.
Heavy Shock — not more than 15 minutes in 2 hours.
1.50
Moderate Shock — more than 10 hours per day.
1.75 Heavy Shock — not more than 10 hours per day.
2.0 Heavy Shock — more than 10 hours per day.
Heavy shock loads and/or severe wear conditions may require
the use of higher service factors. Consultation with factory is
recommended in these applications.

Gear Catalog 67
 MITER GEARS
STEEL & IRON — STRAIGHT TOOTH L-Series–Unhardened Steel
1:1 RATIO HLK Series–Hardened Steel (Teeth only)
OA Series–Cast Iron

APPROXIMATE HP & TORQUE* RATINGS FOR CLASS I SERVICE (Service Factor = 1.0)
Catalog 50 RPM 100 RPM 200 RPM 300 RPM 600 RPM 900 RPM 1200 RPM 1800 RPM
Number Pitch HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque
L110Y .02 25.2 .03 18.9 .06 18.9 .09 18.9 .15 15.8 .21 14.7 .26 13.7 .33 11.6
16
L111Y .03 37.8 .05 31.5 .10 31.5 .13 27.3 .24 25.2 .32 22.4 .38 20.0 .48 16.8
L101Y
L125Y 12 .03 37.8 .06 37.8 .12 37.8 .17 35.7 .29 30.5 .40 28.0 .47 24.7 .59 20.7
L126Y
HLK110Y .06 37.8 .12 37.8 .18 37.8 .30 31.5 .42 29.4 .52 27.3 .66 23.1
16 .04 50.4
L112Y .07 44.1 .14 44.1 .20 42.0 .30 31.5 .44 30.8 .52 27.3 .64 22.4
L102Y 12 .05 63.0 .09 56.7 .18 56.7 .25 52.5 .42 44.1 .56 39.2 .66 34.7 .81 28.4
L127Y
L119Y
L120Y 12 .07 88.2 .14 88.2 .25 78.7 .35 73.5 .60 63.0 .77 53.9 .90 47.3 1.1 38.5
L121Y
L133Y
HLK101Y .06 75.6 .12 75.6 .24 75.6 .34 71.4 .58 60.9 .96 67.2 1.1 57.8 1.3 45.5
L113Y 12 .09 113 .17 107 .33 104 .45 94.5 .75 78.8 .96 67.2 1.1 57.8 1.3 45.5
HLK102Y .10 126 .18 113 .36 113 .50 105 .84 88.2 1.1 77.0 1.3 68.3 1.6 56.0
L103Y
L128Y 10 .11 139 .20 126 .37 117 .52 109 .87 91.4 1.1 77.0 1.3 68.3 1.5 52.5
L129Y
L114Y .15 189 .29 183 .52 164 .71 149 1.1 116 1.4 98.0 1.6 84.0 1.9 66.5
12
HLK121Y .14 176 .28 176 .50 157 .70 147 1.2 126 1.5 105 1.8 94.5 2.2 77.0
L130Y
L104Y 10 .18 227 .33 208 .61 192 .83 174 1.3 137 1.6 112 1.7 89.3 2.2 77.0
L131Y
HLK103Y 10 .20 252 .40 252 .74 233 1.0 210 1.7 179 2.2 154 2.6 137 3.1 109
HLK129Y
OA828Y-1 8 .28 353 .53 334 .93 293 1.2 252 1.9 200 2.3 161 — — — —
L105Y-A
L115Y 8 .30 378 .56 353 1.0 315 1.4 294 2.1 221 2.6 182 3.0 158 3.4 119
L116Y
HLK114Y 12 .29 366 .58 365 1.0 315 1.4 294 2.3 242 2.8 196 3.2 168 3.9 137
OA832Y-1 8 .37 466 .68 428 1.2 378 1.6 336 2.4 252 2.8 196 — — — —
HLK104Y
HLK130Y 10 .33 416 .66 416 1.2 378 1.7 357 2.6 273 3.3 231 3.8 200 4.5 158
HLK131Y

Ratings are based on strength calculation. Basic Static Strength Rating, or for hand operation of above gears is approximately 3 times the 100 RPM rating.
NOTE: Ratings to right of heavy line are not recommended, as pitch line velocity exceeds 1000 feet per minute. Use for interpolation purposes only.
*Torque Rating (Lb. Ins.)

68 Gear Catalog
 MITER GEARS
STEEL & IRON — STRAIGHT TOOTH L-Series–Unhardened Steel
1:1 RATIO HLK Series–Hardened Steel (Teeth only)
OA Series–Cast Iron

APPROXIMATE HP & TORQUE* RATINGS FOR CLASS I SERVICE (Service Factor = 1.0)
Catalog 50 RPM 100 RPM 200 RPM 300 RPM 600 RPM 900 RPM 1200 RPM 1800 RPM
Number Pitch HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque
L106Y
L117Y 8 .42 529 .79 498 1.4 441 1.9 399 2.8 294 3.4 238 3.8 200 — —
L132Y
OA624Y 6 .46 580 .87 548 1.5 472 2.0 420 3.0 315 3.5 245 — — — —
L123Y 8 .55 693 1.0 630 1.8 567 2.4 504 3.5 368 4.2 294 4.6 242 — —
HLK105YA
HLK115Y 8 .55 693 1.1 693 2.0 630 2.7 567 4.3 452 5.3 371 5.9 310 6.9 242
HLK116Y
L107Y 6 .69 870 1.3 819 2.2 693 3.0 630 4.5 473 5.3 371 5.8 305 — —
L118Y
OA630Y-1 6 .82 1034 1.5 945 2.5 787 3.2 672 4.7 494 — — — — — —
OA525Y 5 .90 1134 1.6 1008 2.7 850 3.5 735 5.1 536 — — — — — —
L134Y 6 .90 1134 1.6 1008 2.8 882 3.7 777 5.4 567 6.4 448 7.0 368 — —
L135Y
HLK106Y
HLK117Y 8 .80 1008 1.6 1108 2.8 882 3.7 777 5.7 599 6.8 476 7.6 399 — —
HLK132Y
OA636Y-1 6 1.1 1387 1.9 1197 3.2 1008 4.1 861 5.8 609 — — — — — —
HLK123Y 8 1.0 1260 2.0 1260 3.6 1134 4.7 987 7.0 735 8.4 588 9.2 483 — —
L108Y
L122Y 5 1.3 1639 2.4 1512 4.1 1291 5.3 1113 7.6 798 9.0 630 — — — —
L136Y
HLK107Y 6 1.3 1639 2.6 1638 4.5 1417 6.0 1260 8.0 840 11.0 770 12.0 630 — —
HLK118Y
OA424Y 4 1.6 2017 2.8 1764 4.6 1449 5.9 1239 8.2 861 — — — — — —
OA540Y-1 5 2.0 2521 3.5 2205 5.6 1764 7.0 1470 — — — — — — — —
L109Y 4 2.3 2899 4.2 2646 7.0 2205 8.7 1827 12.4 1302 14.3 1001 — — — —
L137Y
L138Y 4 3.0 3781 5.3 3339 8.6 2709 10.8 2268 14.6 1533 16.6 1162 — — — —
HLK108Y 5 2.4 3026 4.9 3087 8.2 2583 10.0 2100 15.0 1575 18.0 1260 — — — —
HLK122Y
HLK109Y 4 4.2 5294 8.3 5529 14.0 4410 17.0 3510 25.0 2625 28.0 1960 — — — —

Ratings are based on strength calculation. Basic Static Strength Rating, or for hand operation of above gears is approximately 3 times the 100 RPM rating.
NOTE: Ratings to right of heavy line are not recommended, as pitch line velocity exceeds 1000 feet per minute. Use for interpolation purposes only.
*Torque Rating (Lb. Ins.)

Gear Catalog 69
 BEVEL GEARS
STEEL & IRON — STRAIGHT TOOTH L-Series/PA Series Pinions–Unhardened Steel
PA Series–Cast Iron
HL Series–Hardened Steel (Teeth Only)

APPROXIMATE HP & TORQUE* RATINGS FOR CLASS I SERVICE (Service Factor = 1.0)
Catalog †50 RPM 100 RPM 200 RPM 300 RPM 600 RPM 900 RPM 1200 RPM 1800 RPM
Number Pitch Ratio HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque
L146Y 16 .03 37.9 .06 37.1 .11 35.6 .16 34.2 .29 30.7 .40 27.8 .48 25.4 .62 21.7
HL146Y 16 .04 52.6 .08 51.5 .16 49.4 .23 47.5 .41 42.6 .55 38.6 .67 35.3 .86 30.1
L151Y 12 1-1/2:1 .10 128 .20 124 .37 117 .53 111 .91 95.1 1.19 83.4 1.41 74.2 1.74 60.8
HL151Y 12 .14 178 .27 173 .52 163 .73 154 1.26 132 1.65 116 1.96 103 2.41 84.5
L153Y 10 .24 296 .45 285 .84 263 1.17 245 1.93 203 2.47 173 2.88 151 3.44 120
HL153Y 10 .33 412 .63 395 1.16 366 1.62 341 2.68 282 3.44 241 4.00 210 4.77 167
L148Y 16 .02 20.4 .03 20.1 .06 19.5 .09 18.9 .17 17.3 .23 16.0 .28 14.9 .37 13.1
HL148Y 16 .02 28.3 .04 27.9 .09 27.0 .12 26.2 .23 24.1 .32 22.3 .39 20.7 .52 18.1
L149Y 16 2:1 .04 55.8 .09 54.6 .17 52.4 .24 50.4 .43 45.2 .58 40.9 .71 37.4 .91 31.9
L150Y 14 .05 60.6 .09 59.3 .18 57.0 .26 54.8 .47 49.1 .64 44.5 .77 40.6 .99 34.7
HL150Y 14 .07 84.2 .13 82.4 .25 79.1 .36 76.1 .65 68.2 .88 61.8 1.07 56.5 1.38 48.2
HL149Y 16 .06 77.5 .12 75.9 .23 72.8 .33 70.0 .60 62.7 .81 56.8 .99 52.0 1.27 44.3
PA3212Y 12 .04 50.4 .09 56.7 .16 50.4 .23 48.3 .40 42.0 .52 36.4 .62 32.55 .76 26.6
PA4212Y 12 .08 101 .16 101 .29 91.3 .41 86.1 .68 71.4 .87 60.9 1.00 52.50 1.20 42.0
L152Y 12 2:1 .14 174 .27 169 .50 159 .72 150 1.23 129 1.62 113 1.92 101 2.36 82.5
PA5210Y 10 .15 189 .28 176 .51 161 .70 147 1.10 115 1.40 98.0 1.60 84.00 — —
HL152Y 12 .19 242 .37 234 .70 221 .99 209 1.71 179 2.24 157 2.66 140 3.27 115
L155Y 10 .30 384 .58 369 1.08 341 1.51 318 2.50 263 3.20 224 3.73 196 4.45 156
PA528Y 8 .20 252 .38 239 .70 220 .96 202 1.50 157 1.90 133 2.20 115.50 — —
L156Y 8 .54 686 1.03 652 1.88 594 2.59 545 4.16 437 5.21 365 5.96 313 6.97 244
HL155Y 10 2:1 .42 533 .81 512 1.50 474 2.10 441 3.48 365 4.45 312 5.18 272 6.18 217
PA626Y 6 .40 504 .75 472 1.30 409 1.80 378 2.90 304 3.50 245 4.00 210 — —
PA625Y 5 .43 542 .82 517 1.50 472 2.00 420 3.10 325 3.80 266 4.30 225.75 — —
PA726Y 6 .48 605 .89 561 1.60 504 2.10 441 3.90 409 — — — — — —
L158Y 6 1.07 1350 2.02 1272 3.62 1140 4.92 1033 7.67 806 9.43 660 10.65 559 12.24 429
PA826Y 6 .63 794 1.20 756 2.00 630 2.70 567 4.00 420 4.80 336. — — — —
HL156Y 8 2:1 .76 952 1.44 905 2.62 824 3.60 757 5.78 607 7.24 507 8.28 435 9.68 339
PA824Y 4 .98 1235 1.80 1134 3.20 1008 4.20 882 7.30 1766 7.50 525 — — — —
HL158Y 6 1.49 1875 2.80 1766 5.02 1583 6.83 1434 10.65 1119 13.10 917 14.79 777 17.00 595
PA3316Y 16 .05 68.7 .11 67.2 .20 64.5 .30 62.0 .53 55.6 .72 50.4 .88 46.1 1.12 39.3
PA45312Y 12 .16 203 .31 197 .59 186 .84 176 1.44 151 1.89 132 2.24 118 2.75 96.5
PA6310Y 10 .34 431 .66 414 1.21 383 1.70 356 2.81 295 3.60 252 4.18 220 5.00 175
PA638Y 8 3:1 .43 538 .82 516 1.52 478 2.12 445 3.51 368 4.49 314 5.22 274 6.24 218
L157Y 10 .34 431 .66 414 1.21 383 1.70 356 2.81 295 3.60 252 4.18 220 5.00 175
PA7536Y 6 .88 1103 1.66 1049 3.03 955 4.17 876 6.69 703 8.38 587 9.59 504 11.21 393
PA935Y 5 1.53 1925 2.88 1813 5.16 1625 7.01 1472 10.93 1149 13.44 942 15.19 798 17.45 611
PA4416Y 16 .06 79.7 .12 78.0 .24 74.9 .34 72.0 .61 64.5 .83 58.5 1.02 53.4 1.30 45.6
PA6412Y 12 .17 209 .32 203 .61 191 .86 181 1.48 155 1.94 136 2.31 121 2.83 99.2
PA6410Y 10 4:1 .22 276 .42 268 .80 252 1.13 238 1.95 205 2.56 179 3.04 160 3.74 131
PA848Y 8 .43 546 .83 524 1.54 485 2.15 452 3.56 374 4.56 319 5.30 278 6.33 222
PA948Y 8 .75 943 1.43 901 2.62 827 3.64 764 5.92 622 7.50 525 8.65 454 10.21 357
PA6616Y 16 6:1 .09 112 .17 109 .33 105 .48 101 .86 90.3 1.17 81.9 1.42 74.8 1.82 63.9
PA6612Y 12 .12 147 .23 144 .44 138 .63 133 1.13 119 1.54 108 1.88 98.6 2.40 84.2

Ratings are based on strength calculation. Basic Static Strength Rating, or for hand operation of above gears is approximately 3 times the 100 RPM rating.
*Torque Rating (Lb. Ins.)
†RPM of Pinion

70 Gear Catalog
 STEEL SPIRAL MITER & BEVEL GEARS
STEEL SPIRAL MITER GEARS LSA-Series–Unhardened Steel
1:1 RATIO HLSK Series–Hardened Steel (Teeth Only)

APPROXIMATE HP & TORQUE* RATINGS FOR CLASS I SERVICE (Service Factor = 1.0)
Catalog 50 RPM 100 RPM 200 RPM 300 RPM 600 RPM 900 RPM 1200 RPM 1800 RPM
Number Pitch HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque
LSA110Y 18 .01 12.6 .02 12.6 .04 12.6 .07 14.7 .14 14.7 .20 14.0 .25 13.1 .35 12.2
LSA101Y 12 .02 25.2 .04 25.2 .08 25.2 .13 27.3 .25 26.2 .35 24.5 .45 23.6 .62 21.7
LSA102Y 12 .03 37.8 .07 44.1 .13 40.9 .20 42.0 .38 39.9 .54 37.8 .63 33.1 .95 33.2
HLSK110Y 18 .03 37.8 .07 44.1 .14 44.1 .21 44.1 .42 44.1 .59 41.3 .76 39.9 1.0 35.0
HLSK101Y 12 .06 75.6 .13 81.9 .26 81.9 .39 81.9 .75 78.7 1.0 70.0 1.3 68.2 1.8 63.0
LSA103Y 10 .07 88.2 .15 94.5 .30 94.5 .44 92.4 .80 84.0 1.1 77.0 1.4 73.5 2.0 70.6
HLSK102Y 12 .10 126. .21 132. .41 129. .61 128 1.0 105 1.6 112 2.0 105 2.8 98.0
LSA104Y 10 .15 189. .30 189. .57 180. .83 174 1.5 151 2.0 140 2.6 136 3.6 126
LSA105YA 7 .22 277. .44 277. .84 265. 1.2 252 2.2 231 3.0 210 3.8 199 5.1 178
HLSK103Y 10 .23 290. .46 290. .89 280. 1.3 273 2.4 252 3.4 238 4.3 226 5.9 206
LSA106Y 8 .34 429. .69 435. 1.3 409. 1.8 378 3.3 346 4.5 315 5.7 299 7.8 273
LSA107Y 6 .46 580. .90 567. 1.7 535. 2.4 504 4.3 451 5.9 413 7.4 388 10.0 350
LSA118Y 6
HLSK104Y 10 .45 567. .90 567. 1.7 535. 2.5 525 4.5 472 6.1 427 7.9 415 11.1 388
HLSK105YA 7 .67 845. 1.3 819. 2.5 787. 3.6 756 6.5 682 9.0 630 11.0 577 15.0 525
LSA122Y 5 .83 1046. 1.6 1008. 3.0 945. 4.3 903 7.5 787 10.0 700 12.0 630 17.0 595
HLSK106Y 8 1.0 1260. 2.0 1260. 3.9 1228. 5.6 1176 10.0 1050 13.0 910 17.0 892 23.0 805
HLSK107Y 6 1.3 1639. 2.7 1701. 5.1 1606. 7.3 1533 13.0 1365 17.0 1190 22.0 1155 33.0 1155
HLSK118Y 6
HLSK122Y 5 2.4 3025. 4.9 3087. 9.1 2866. 13.1 2751 23.1 2425 30.0 2100 38.0 1995 51.0 1785

STEEL SPIRAL BEVEL GEARS** SS-Series–Unhardened Steel

2:1 RATIO SH Series–Hardened Steel (Teeth Only)

APPROXIMATE HP & TORQUE* RATINGS FOR CLASS I SERVICE (Service Factor = 1.0)
Catalog 50 RPM† 100 RPM† 200 RPM† 300 RPM† 600 RPM† 900 RPM† 1200 RPM† 1800 RPM†
Number Pitch HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque HP Torque
SS302 30 .002 2.5 .004 2.5 .008 2.5 .013 2.7 .025 2.6 .037 2.6 .05 2.6 .07 2.4
SH302 30 .005 6.3 .01 6.3 .02 6.3 .03 6.3 .06 6.3 .09 6.3 .12 6.3 .18 6.3
SS192 19 .01 12.6 .02 12.6 .04 12.6 .06 12.6 .12 12.6 .18 12.6 .24 12.6 .35 12.2
SS142 14 .02 25.2 .05 31.5 .09 28.3 .14 29.4 .26 27.3 .39 27.3 .51 26.8 .76 26.6
SH192 19 .03 37.8 .05 31.5 .10 31.5 .16 33.6 .31 32.5 .46 32.2 .60 31.5 .88 30.8
SS142-1 14 .04 50.4 .08 50.4 .16 50.4 .23 48.3 .45 47.2 .67 46.9 .88 46.2 1.3 45.5
SH142 14 .06 75.6 .12 75.6 .23 72.4 .34 71.4 .66 69.3 .98 68.6 1.3 68.2 1.9 66.5
SH142-1 14 .10 126 .20 126 .39 123 .58 122 1.1 115 1.7 119 2.2 115 3.2 112
SS102 10 .14 176 .27 170 .52 164 .78 164 1.5 151 2.2 154 2.9 152 4.3 150
SS82 8 .26 328 .50 315 .99 312 1.5 315 2.8 294 4.2 294 5.5 289 8.0 280
SH102 10 .34 429 .67 422 1.3 409 2.0 420 3.8 399 5.6 392 7.3 383 10.7 374
SH82 8 .64 807 1.3 819 2.5 787 3.7 777 7.1 745 10.5 735 13.7 719 20.0 700

Ratings are based on strength calculation. Basic Static Strength Rating, or for hand operation of above gears is approximately 3 times the 100 RPM rating.
*Torque Rating (Lb. Ins.)
**Ratings reflect Gear and Pinion sets.
†Pinion RPM

Gear Catalog 71
 NOTES

72 Gear Catalog