Ballast Dimmer, 0-10V Output

HDL-MRDA0610.432

Parameters Overview
Electrical Parameters:
Buspro Working Voltage DC15~30V

Buspro Power Consumption 30mA/DC24V

Relay Channel Output 6CH/10A

6CH/100mA (Total current is less
0-10V Output
than 300mA)

Environmental Conditions:
Working Temperature -5℃~45℃
Working Relative Humidity Up to 90% HDL－MRDA0610.432 6-channel 10A DC0 －10V output
Storage Temperature -20℃~+60℃ module is a multifunction control module. It has 6-channel
Storage Relative Humidity Up to 93% relay outputs and it is suitable for switch control. It has 6–
channel for 0-10V analog signal outputs (supports input and
Approved
output. It can control the 0-10V Dimmable fluorescent Tube,
CE
0-10V LED light, etc. The module is to be used in lighting ,
RoHS
switch control in the office and building area.
Product Information:
Dimensions 144×90×66 (mm)
Net weight 449.5(g)
Housing Material Nylon, PC Functions
Installation 35mm DIN rail installation ■ Up to 6 separate areas, max 12 scenes in each area
Protection rating IP20 ■ Up to 6 sequence, each sequence has 12 steps，
running time for each step is 60 minutes, the sequence
has 4 running modes: “forward”, “backward”, “forward
Important Notes and backward”, “random”
■ Buspro cable - HDL Buspro/KNX cable, 0.8mm single-core cop- ■ Low, high, max threshold for each channel, suitable for
per cable different load
■ Buspro connection - Series connection (hand-in-hand) ■ Bypass button for manual control available for each
■ Load in each channel – Less than 800w dimmable fluorescent channel
tube ■ You can select specified scene or scene before power
■ 0-10V Load - Output in each channel is 100mA, total in 6 chan- off when device restarts
nels are less than 300mA ■ Easy programming mode is available
■ Extra Power Input -0-10V Output need connect a Exterior 24V DC ■ Supports HDL Buspro Pro online upgrading
Power supply. Power supply from HDL Buspro is not allowed
■ Each channel needs to connect to a breaker or fuse for protection
■ Connection checking – Check all connection after installation
Installation Steps
■ 35mm DIN rail installation, inside DB box.

HDL Buspro Cable Guide ■ Connect Load, 0-10V cable, HDL Buspro cable.
■ Check the HDL Buspro connection, avoid any mis-
HDL Buspro HDL Buspro/KNX
takes.
DC24V Red
■ Check the load connection and 0-10V, make sure the
COM Black
positive and negative poles are connected correctly.
DATA- White
DATA+ Yellow

Do you need help? Contact with us

Professional Home and Building Automation
www.hdlautomation.com(171208) [email protected] 1/ 2
www.hdlchina.com
Ballast Dimmer, 0-10V Output
HDL-MRDA0610.432

Dimensions and Wiring

144 66

HDL

90

Front View Side view

－
+ Tube
Indicator for module and easy programming mode
L Ballast
N Indicator: Flickers when the module is working prop-
AC220v erly. Keep pressing the indicator for 3 seconds, it
turns to red , then user can read and modify the
address of the module in the HDL Buspro Pro set up
software.
Channel Indicator
Steps for easy programming mode：
1 Press the programming button for about 20s，
Bypass Button then all output channels will be turn off automati-
cally the indicator will flicker fast.
Module indicator 2 Press Button 9 and 10 of DLP switch together to
& program button, enter programming mode.
3 Turn on the channel which needs to program by

6 channel 0-10V Extra 24V DC Input HDL Buspro interface using the bypass button
4 Choose a button which is used to control the
Note：Take the connection of channel 1 as an example channel.
5 Press the indicator again, finish the programming.
This function is to be used with the new generation
of DLP.

Safety Precautions
■ Each channel needs to connect breaker or fuse for protection.
■ The screw down strength should not exceed 0.4Nm.
■ HDL Buspro cable: 0.8mm single-core copper cable.
■ Installation-Inside DB box.
■ Do not make wrong connection on Buspro interface, it will damage the Buspro interface of this module.
■ Do not get AC power into Buspro wire , it will damage all devices in the system.
■ Do not let the module come into contact with liquids and corrosive gases.
■ Ensure good ventilation.

Packing List
■ Datasheet ×1
■ Ballast Dimmer (HDL-MRDA0610.432 ) ×1

Do you need help? Contact with us

Professional Home and Building Automation
www.hdlautomation.com(171208) [email protected] 2/ 2