Scribd Logo
Upload

Welcome to Scribd!

  • 64 views

    Maintenance Manual

    Uploaded by

    Douglas de Oliveira
    This document provides instructions for inspecting and replacing the filter in an air conditioning system shutoff valve. The procedure involves removing existing parts, inspecting and cleaning or replacing the filter, testing the new filter, and reinstalling parts. Filters should be replaced at each inspection interval for efficiency. Technicians are warned to ensure the filter is installed with the capped end toward the plug.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Maintenance Manual

    Uploaded by

    Douglas de Oliveira
    64 views4 pages
    This document provides instructions for inspecting and replacing the filter in an air conditioning system shutoff valve. The procedure involves removing existing parts, inspecting and cleaning or replacing the filter, testing the new filter, and reinstalling parts. Filters should be replaced at each inspection interval for efficiency. Technicians are warned to ensure the filter is installed with the capped end toward the plug.

    Original Title

    21-01-00-ic

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for inspecting and replacing the filter in an air conditioning system shutoff valve. The procedure involves removing existing parts, inspecting and cleaning or replacing the filter, testing the new filter, and reinstalling parts. Filters should be replaced at each inspection interval for efficiency. Technicians are warned to ensure the filter is installed with the capped end toward the plug.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    64 views4 pages

    Maintenance Manual

    Uploaded by

    Douglas de Oliveira
    This document provides instructions for inspecting and replacing the filter in an air conditioning system shutoff valve. The procedure involves removing existing parts, inspecting and cleaning or replacing the filter, testing the new filter, and reinstalling parts. Filters should be replaced at each inspection interval for efficiency. Technicians are warned to ensure the filter is installed with the capped end toward the plug.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Title Page Prev Page Next Page TOC

    MAINTENANCE MANUAL

    AIR CONDITIONING SYSTEM SHUTOFF AND FLOW REGULATOR VALVE — INSPECTION / CHECK
    1. Air Conditioning Shutoff Valve Filter — Inspection
    A. Preparation
    REPLACEMENT PARTS
    GSK kit ...................................................................................................... 1159CGSK212077/212078
    Each kit consists of:
    O-ring ............................................................................................................................ S8990-013 (1)
    NOTE: The following part is not included in GSK kit. Order separately as required.
    Filter ................................................................................................................................. 111790-5 (1)
    B. Procedure
    (1) Removal (See Figure 601.)
    (a) Remove plug (1), washer (2), O-ring (3), spring (4), washers (5, 6), filter (7), washer (8)
    and retainer (9).
    (b) Inspect and clean filter or replace with new filter, see Step 1.B.(2).
    NOTE: Comparing low relative cost of filter with cost of manhours involved in cleaning
    and testing, it is suggested that filter is changed at each inspection interval.
    CAUTION: ENSURE THAT FILTER (7) IS INSTALLED WITH CAPPED END TOWARD
    PLUG, OTHERWISE NO CONTROL AIR CAN ENTER VALVE.
    (2) Clean filter in accordance with AlliedSignal Maintenance Manual procedures.
    (3) Filter Testing
    (a) Install filter in test setup similar to that shown in Figure 602 and constructed as follows:
    1 Using ¼ inch metal tubing, install regulator in line with two AN815-4 nipples.
    2 Install two gages with AN824-4 tees.
    3 Make orifice from AN815-4 union plugged to a depth of 1/8 inch and drilled 0.042
    inch through.
    4 Connect filter to line with quick-coupler (Type 637, Superior Valve and Fitting Co.,
    Pittsburgh, Pennsylvania).
    5 Use filtered compressed air at 80°F ±40°F.
    (b) Adjust regulator to apply inlet air pressure of 20 psig at inlet air pressure gage.
    (c) Discard filter if pressure indicated on the downstream air pressure gage exceeds 3.5 psig.
    (4) Filter Installation See Figure 601.
    (a) Ensure that old filter has been cleaned and tested per procedures specified in Steps
    1.B.(2) and 1.B.(3) above or that new filter is to be installed.
    (b) Ensure O-ring (3) is replaced regardless of condition.
    (c) Replace worn washers and spring as required.
    (d) Check plug for galling and cross threading.

    21-01-00
    Page 601
    December 31/02
    Title Page Prev Page Next Page TOC

    MAINTENANCE MANUAL

    CAUTION: ENSURE THAT FILTER (7) IS INSTALLED WITH CAPPED END TOWARD
    PLUG, OTHERWISE NO CONTROL AIR CAN ENTER VALVE.
    (e) Replace retainer (9), washer (8), filter (7), washers (5, 6), spring (4), new O-ring (3),
    washer (2) and plug (1).
    (f) Perform leak check.
    (g) Record all maintenance actions in accordance with current Federal Aviation Regulations.

    21-01-00
    Page 602
    December 31/02
    Title Page Prev Page Next Page TOC

    MAINTENANCE MANUAL

    Filter Removal and Replacement


    Figure 601

    21-01-00
    Page 603
    December 31/02
    Title Page Prev Page Next Page TOC

    MAINTENANCE MANUAL

    Filter Assembly Test Setup


    Figure 602

    21-01-00
    Page 604
    December 31/02

    You might also like