Rectangular Flange Design
Pressione di Design Pd 5 MPa
Sovraspessore di corrosione C.A. 3 mm
Outside lenght of Long side Al 2620 mm
Outside lenght of Short side As 775 mm
Inside lenght of Long side Bl 2373.5 mm
Inside lenght of Short side Bs 528.5 mm
End bolt c/ to c/ long side Cl 2520 mm
OK
Max spacing between bolts on long side Lmax_l 127.9 mm
End bolt c/ to c/ short side Cs 675 mm
OK
Max spacing between bolts on short side Lmax_s 127.9 mm
Altezza codolo g1 0 mm
Gasket OD long side Gol 2440 mm
Gasket ID long side Gil 2370 mm
Gasket OD short side Gos 600 mm
Gasket ID short side Gis 530 mm
Numero bulloni Nb 62
Gasket material EPDM
Gasket factor m 3.75
Design seating stress y 52 MPa
Material of Flanges P355 NH
Yield stress at ambient temperature Sfy 260 MPa
Allowable stress at design temperature Sfd 136 MPa
Allowable stress at ambient temperature Sfa 138 MPa
Youngs Modulus for flange @ Design Ef 185000 MPa
Material of bolt / studs SA-193 Gr. B7
Bolt size M42
Bolt diameter d 42 mm
Bolt hole diameter df 42 mm
Root area per bolt / studs Ra 1018.218 mm2
Yield stress at ambient temperature Sby 695 MPa
Allowable stress at design temperature Sbd 172 MPa
Allowable stress at ambient temperature Sba 172 MPa
Spessore verificato
Selecting flange thickness (excluding RF) tact 125 mm
Width of gasket ( Go - Gi ) / 2 N 35.00 mm
When bo< 6.3 mm ; b = bo else b = 2.5 x root (bo)
Effective width of gasket (N/2) bo 17.50 mm
Effective width of gasket b 10.46 mm
Gasket reaction Long side ( Gol - 2b ) Gl 2419.08 mm
Gasket reaction Short side ( Gos - 2b ) Gs 579.08 mm
Hydrostatic end force ( Pd * Gl * Gs ) H 7004256.69 N
Compression Load on Gasket ( 2b * (2Gl + 2Gs) * m * Pd) HG 2351668.58 N
Hydrostatic end force applied via shell ( Pd * Bl * Bs ) HD 6271973.75 N
Hydrostatic end force due to pressure ( H-HD ) HT 732282.94 N
Min required bolting Loads
Min. bolt Load for Operating Condition ( HG + H ) Wm_1 9355925.27 N
Min. bolt Load for Gasket Seating Condition ( 2 * ( Gl + Gs ) * b * y ) Wm_2 3260980.42 N
Design Flange Load max ( WM1; Wm2 ) Ww 9355925.27
Bolt Area for operating condition Wm_1 / Sbd Am_1 54394.91 mm2
Bolt Area for gasket seating condition Wm_2 / Sba Am_2 18959.19 mm2
Min. Design Bolt Area requirement max.(Am1, Am2) Am 54394.91 mm2
Actual Bolt Area Ab 63129.516 mm2
The no. Of bolts selected is safe
Moment Arms
Radial distance from Bolt circle to I.D. - Long side ( Cl - Bl - g_1) / 2 hD_d 73.25 mm
Radial distance from Bolt circle to G.I.D. - Long side ( Cl - Gl) / 2 hG_g 50.46 mm
Radial distance from Bolt circle to circle at which HT acts ( 2 x Cl - Bl - Gl) / 4 hT_t 61.85 mm
Max Operating Moment ( HD*hd + HG*hg + HT*ht ) Mop 623377879.49581 N mm
Maximum Gasket Seating Moment ( Ww * hG_g ) Matm 472083619.13303 N mm
Flange thickness calculation check
Operating Condition (6 Mop / (Sfd * (2*(Cl+Cs)-n*df)))^0.5 to 85.23 mm
Gasket Seating Condition (6 Matm / (Sfa * (2*(Cl+Cs)-n*df)))^0.5 tg 73.63 mm
Min required thickness ( max. (to, tg ) tmon 85.23 mm
Max permissible spacing Pbmax 257.06 mm
Dimension check for Flange design (Al-Bl)-(As-Bs) = 0 0
The dimensions are acceptable
Dimension check for Flange design (Cl-Bl)-(Cs-Bs) = 0 0
The dimensions are acceptable
Lato a' 1000 mm
Lato b' 1000 mm
Pressione P 0.081 Mpa
Soll. Ammiss. F 150 MPa
Spessore SP 20 mm
c.a. 3 mm
TL 0.4 mm
a'/b' 1
fattore C3 0.66 da Fig. 10.7-2
e 18.73701 mm "<" 20 Spessore SP
