Cisco Packet Tracer Project

FOR THE PURPOSE OF
CERTIFICATION
NAME:RAKTIM MUKHOPADHYAY
COLLEGE:GOVT. COLLEGE OF ENGG. AND
CERAMIC TECHNOLOGY
DEPT: COMPUTER SCIENCE AND ENGG.
DATE OF EXAM:22TH JULY 2016
QUESTION I
CONFIGURE SEVEN 18XX
ROUTERS IN SERIES USING
OSPF.
ROUTER CONNECTIVITY WITH OSPF COMMANDS:

OSPF stands for Open Shortest Path First. OSPF is a
link state open standard based routing protocol.
A topology as demonstrated in the picture is
created using Cisco Packet Tracer Student v6.2.
Eight CISCO 1841 Routers are connected together
across its serial interfaces via Serial DCE and DTE
cables.
Configuring each Router:
1.Double click on each Router
2.Under the Physical tab, we find the back side of
the router where we need to power off the router
and add a Wan Interface Card (WIC) and then turn
the router back on. In this case, we use WIC-2T for
the purpose.
TAKING 7 ROUTERS CONNECTING THEM BY FIRST CONFIGURING THE IP IN
RESPECTIVE PORTS, THEN USING OSPF COMMAND INTERCONNECTING THEM.
SOURCE CODES CONFIGURING CISCO ROUTER 1811
FOR CONFIGURING ROUTER CONNECTIONS
Router 1:
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int s0/0/1
Router(config-if)#ip address 1.1.1.1 255.0.0.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

Router(config-if)#int s0/0/0

Router(config-if)#
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0,

changed state to up
Router 2
Router>en
Router#config t
Router(config-if)#
Router(config-if)#int
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed
state to up
Router(config-if)#
Router 3
Router>en
Router#config t
Router(config-if)#
state to up

Router 4
Router>en
Router#config t

state to up
Router 5
Router>en
Router#config t
Router(config-if)#
Router(config-if)#int
state to up

Router 6
Router>en
Router#config t
state to up
Router 7
Router>en
Router#config t
state to up


Configure OSPF routing protocol:
Enabling OSPF is a two-step process: -
1.Enable OSPF routing protocol from global configuration mode.
2.Tell OSPF which interfaces we want to include.
For these steps following commands are used respectively.
Router(config)# router ospf processID
Router(config-router)# network IPnetwork_[wild card mask] Area
Number area number
This code is same for all the routers. For Router 1 code is shown:
ROUTER 1
Router>en
Router#config t
Router(config)#router ospf 1
Router(config-router)#network 1.0.0.0 0.255.255.255 area 0
CLI SCREEN SHOWING OSPF COMMANDS
Image showing success in dispatching packet data.

QUESTION II
CONFIGURE TELEPHONY
SERVICE USING 2811 ROUTER
STEP 1:
Configure interface FastEthernet 0/0 and DHCP server on
Router (2811 router)
STEP 2:
Configure the Call Manager Express telephony service on
Router
STEP 3:
Configure a voice VLAN on Switch
STEP 4:
Configure the phone directory for IP Phones
Image represents attaching of WIC-2T card to CISCO
ROUTER 2811
SOURCE CODE FOR CONFIGURING CISCO ROUTER 2811
Router>en
Router#config t
Enter configuration commands, one per line. End
with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed
state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#ip dhcp pool test

Router(dhcp-config)#network 12.0.0.0 255.0.0.0
Router(dhcp-config)#default-router 12.12.12.12
Router(dhcp-config)#option 150 ip 12.12.12.12
Router(dhcp-config)#telephony-service
Router(config-telephony)#max-ephones 10
Router(config-telephony)#max-dn 10
Router(config-telephony)#ip source-address
12.12.12.12 port 2000
Router(config-telephony)#auto assign 1 to 10
Router(config-telephony)#auto assign 3 to 8
Router(config-telephony)#exit
Router(config)#ephone-dn 1
Router(config-ephone-dn)#%LINK-3-UPDOWN: Interface
ephone_dsp DN 1.1, changed state to up
Router(config-ephone-dn)#number 8420713512
Router(config-ephone-dn)#ephone-dn 2
Router(config-ephone-dn)#
Router(config-ephone-dn)#
SOURCE CODE FOR CONFIGURING CISCO SWITCH 2960
Switch>en
Switch#config t
Switch(config)#int range fa0/1-24
Switch(config-if range)#switchport mode access
Switch(config-if range)#switchport voice vlan 1
Switch(config-if range)#
Image represents attaching of IP Phone Power
Adapter card to CISCO ROUTER 2811
Image represents GUI of CISCO IP PHONE

Image represents RING OUT
Image represents RING IN
Image represents CONNECTED
Image represents CONNECTED
Image represents BUSY

Cisco Packet Tracer Project

Uploaded by

Copyright:

Available Formats

Cisco Packet Tracer Project

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cisco Packet Tracer Project

Uploaded by

Copyright:

Available Formats

FOR THE PURPOSE OF

ROUTER CONNECTIVITY WITH OSPF COMMANDS:

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0,

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down

Router(config-if)#ip address 3.3.3.1 255.0.0.0

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down

Router(config-if)#ip address 7.7.7.1 255.0.0.0

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

Image showing success in dispatching packet data.

Router(config-if)#ip dhcp pool test

SOURCE CODE FOR CONFIGURING CISCO SWITCH 2960

Image represents GUI of CISCO IP PHONE

You might also like