Scribd
Upload
98 views1 page

GBM Smart Target Instructions: Instruction Part No. 050144A

The document provides instructions for operating and programming the modes of an Akkerman GBM Smart Target. The target has normal, sleep, low battery, and high temperature modes indicated by different LED patterns. It can also be programmed to adjust LED brightness, turn inner ring LEDs on/off, and change steering line animation. Programming involves a series of rotations within time limits to enter mode, then rotations in different directions to select commands.

Uploaded by

Itzhak Schwartzman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
98 views1 page

GBM Smart Target Instructions: Instruction Part No. 050144A

The document provides instructions for operating and programming the modes of an Akkerman GBM Smart Target. The target has normal, sleep, low battery, and high temperature modes indicated by different LED patterns. It can also be programmed to adjust LED brightness, turn inner ring LEDs on/off, and change steering line animation. Programming involves a series of rotations within time limits to enter mode, then rotations in different directions to select commands.

Uploaded by

Itzhak Schwartzman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

GBM

Smart Target
Instructions
Akkerman Inc.
58256 266th Street • Brownsdale, MN USA 55918
Instruction Part No. 050144A

The Akkerman GBM Smart Target is a multi-functional programmable target.


• Normal mode: all LEDs are on (depending on programming mode) with the steering line LEDs flashing
every second.
• Battery Voltage Indicator is visible at power up for one second. The outer ring LEDs are used as the
gauge. One LED is on, then one LED for every 1/10th volt above 2.3 v.
• Sleep mode* (only center LED flashes) will conserve battery power when the target has not been
rotated more than ± 20° for ten minutes. Wake from sleep mode by simply rotating the target.
• Low Battery mode* (center LED on, outer mots LED on steering line flashing)-LED willOffactivate
-LED On
when -LED theFlashing
battery level reaches <2.1V. Sleep mode will activate in one minute to conserve battery power.
• High Temperature mode* (all LEDs flash) activates when theSleep target
Mode temperature
Low Battery Modeis >131°F (55°C).
High Temperature Mode
- only center LED - center LED on, outer most - all active LEDs flash
High temperature mode deactivates when target temperature is <127°FLED
flashes (53°C).
on steer line flashing

* Refer to illustrations below

Sleep Mode Low Battery Mode High Temperature Mode


- only center LED - center LED on, outer most - all above LEDs flash
flashes LED on steering line flashing

• Programming-LED mode:
Off -LED -LED
On Off -LED
-LED OnOff
Flashing
-LED -LED On
-LED Flashing -LED Flashing
This mode allows the operator to increase/decrease the LED brightness and/or allow the inner LED ring
display to be turned on/off. To enter programming mode, a series of target rotations are required within
various time constraints.
Sleep Mode LowMode
Sleep Battery ModeSleep LowHigh Temperature
Battery
Mode Mode Low ModeHigh
BatteryTemperature
Mode Mode
High Temperature Mode
- only center LED center
- only LED LED
center on, outer -most
center
- only - all
LED
center LEDactive LEDs
on, outer flash
most
- center - allon,
LED active
outerLEDs
mostflash
- all active LEDs flash
flashes EnterLEDProgramming
flashes Mode:
on steer line flashing
LED on steer line flashing
flashes LED on steer line flashing
1. Rotate target and stop with the steering line pointing up to 12 o’clock position.
2. Wait 10 seconds for a single flash to appear, and within 10 seconds rotate target CW one complete
rotation and stop in the up (12 o’clock) position.
3. Wait 10 seconds for a double flash to appear, and within 10 seconds rotate target two complete CW
rotations and stop in the up (12 o’clock) position.
4. Wait 10 seconds for a triple flash to appear, and within 10 seconds rotate target three complete CW
rotations and stop in the up (12 o’clock) position.
5. Wait 10 seconds. You are now in programming mode and only the steering line LEDs should be
illuminated with outer most LED flashing rapidly.
6. Within 10 seconds rotate the target to desired command (see below):

Programming Command Modes:


• Increase LED Brightness: rotate target CW one full rotation with the steering line at the 12 o’clock
position. Once brightness level is achieved, rotate target to store the setting.
• Decrease LED Brightness: rotate target CW 1/2 rotation with steering line at 6 o’clock position. Once
brightness level is achieved, rotate target to store the setting.
• Inner Ring On/Off: rotate target CW 1/4 rotation with steering line at 3 o’clock position. The inner ring
will toggle On/Off. Wait for inner ring to set the on/off position before rotating.
• Steering Line Animation On/Off: rotate target CW 3/4 rotation with steering line at 9 o’clock position.
The steering line animation will toggle.
Reset to factory default mode: Using a solid, level surface, place target cap on surface. The outer ring
LEDs will go off one by one until the complete target LEDs are off. Then all LEDS will blink twice. The
target is now reset to the factory default settings.
GBMSmartTargetInstructions_050144a Page 1 of 1 0918

You might also like