MEBS6008 Environmental Services II

http://me.hku.hk/bse/MEBS6008/

Fluid Network Analysis II

Ir. Dr. Sam C. M. Hui
Visiting Assistant Professor
Department of Mechanical Engineering
The University of Hong Kong
E-mail: [email protected] Aug 2016
Contents

• Pipe Systems and Design

• Pipe Network Analysis

• Water Systems in HVAC

Pipe Systems and Design

• Common types of HVAC piping systems

• Chilled water (CHW) system
• Condenser water (CW) system
• Sea water system
• Hot water supply system
• Steam pipes, gas pipes
• Similar systems in other building services
• Water supply & distribution (plumbing)
[Source: Kreider, K. F. (ed.), 2001. Handbook of Heating, Ventilation, and Air Conditioning, CRC Press, Boca Raton, FL.]
Pipe Systems and Design

• Two major concerns:

• Size the pipe (e.g. from charts & tables)
• Determine the flow-pressure relationship
• To analyse the system, e.g. to find out pump pressure
• By using manual or computer-based methods
• Calculations for pipelines or pipe networks
• Can be very complicated for branches & loops
• Basic parameters: pipe diameter, length, friction
factor, roughness, velocity, pressure drop
Pipe Systems and Design

• Pipe network analysis

• Physical features are known
• Solution process try to determine flow & pressure
at every node
• Pipe network design
• Variables are unknown
• Try to solve & select pipe diameters, pumps,
valves, etc.
Pipe Systems and Design

• Basic equations
• Darcy-Weisbach Equation (for fully developed
flows of all Newtonian fluids)
2 2
L
   V  L
   V 
p  f    or h  f   
 D  2 g   D  2 g 
• Colebrook-White Equation (for transition region):
1  9.3 
 1.14  2 log( D /  )  2 log 1  
f  Re( / D ) f 
• * The equation is implicit in f (appears on both sides), so
iterations are required to solve for f.
 Pipe Systems and Design

• Basic equations (cont’d)

• Hazen-Williams Equation (alternative to Darcy-
Weisbach formula; empirical)
1.852 1.167
V   1 
p  6.819 L    ( g)
C   D
• C = roughness factor (typically, C = 150 for plastic or
copper pipe, C = 140 for new steel pipe, C < 100 for
badly corroded or very rough pipe)

(See also: Darcy-Weisbach equation - Wikipedia http://en.wikipedia.org/wiki/Darcy%E2%80%93Weisbach_equation

Hazen-Williams equation - Wikipedia http://en.wikipedia.org/wiki/Hazen%E2%80%93Williams_equation )
Pipe Systems and Design

• Basic equations (cont’d)

• Exponential formula:
• The previous equations (Darcy-Weisbach or Hazen-
Williams) can be expressed by an exponential form to
generalise the theory
n
h  KQ
• Q = volume flow rate; K, n = coefficient & exponential
• Values for the coefficient and n change, depending on
which equation is used
Pipe Systems and Design

• Valve and fitting losses

• May be greater than pipe friction alone
V 2  V 2 
p  K L    or h  K L  
 2   2g 
• KL = loss coefficient (K factor) of pipe fittings
• Geometry and size dependent
• May be expressed as equivalent lengths of straight pipe
• Valve coefficient (Av):
• Volume flow rate Q  A p / 
v
(Source: Larock, Jeppson and Watters, 2000: Hydraulics of Pipeline Systems)
Pipe Systems and Design

• Practical design issues

• Select a pipe size for desired total flow rate and
available or allowable pressure drop, e.g.
• Often assume 2.5 m / 100 m pipe length
• Velocity limit 1.2 m/s for pipe < 50 mm dia., pressure
drop limit 400 Pa/m for pipe > 50 mm dia.
• Rule of thumb for practical design:
• Assume design pipe length is 1.5 to 2.0 times actual to
account for fitting losses; after pipe diameter is selected,
then evaluate the influence of each fitting
• Other considerations: e.g. noise & water hammer
(Source: ASHRAE Handbook Fundamentals 2005, Chp. 36)
(Source: ASHRAE Handbook Fundamentals 2005, Chp. 36)
Pipe Network Analysis

• Often a complex mathematical problem

• Solving entire set of non-linear equations
• Large networks are usually analysed by computers
• Basis of the computer solutions
• Basic principles of fluid mechanics
• Suitable equations that embody them
• Interrelate the pipe discharge & pressure at each
node of the network
 Pipe network analysis
(Source: Larock, Jeppson and Watters, 2000: Hydraulics of Pipeline Systems)
Pipe Network Analysis

• Basic principles of fluid mechanics

• 1) Conservation of mass (continuity principle)
• 2) Work-energy principle (Darcy-Weisbach or
Hazen-Williams)
• 3) Fluid friction & energy dissipation
• The task is to
• Describe the hydraulic system accurately and
efficiently by means of equations
• Solve these simultaneous equations effectively
Energy Line (EL) and Hydraulic Grade Line (HGL)
(Source: Larock, Jeppson and Watters, 2000: Hydraulics of Pipeline Systems)
 Pipe Network Analysis

• Methods to solve steady flow problem in a

pipe network
• Hardy Cross method
• Adapted from structural engg.
• Oldest systematic method; suited for hand computations
• Convergence problems for large systems
• Newton method
• Linear algebra matrix operations
• Perform iterative set of calculations (using computers)

(See also: Hardy Cross method - Wikipedia http://en.wikipedia.org/wiki/Hardy_Cross_method )

Pipe Network Analysis

• Define an appropriate pipe system

• Decide what features are important & to retain
• No hard rules; requires much insight & judgment
• Determine which demands should be specified
• Analysis for a range of system demands
• For large systems, require some “skeletonization”
• Not all pipes or nodes are included in the analysis
• Some may be lumped at a single node
• After studying the entire system, more detailed
analysis may be done within a building or area
Pipe Network Analysis

• Basic relations between network elements

• Junction Continuity Equations
• Summing volume flows at each junction (or node)
• Energy Loop Equations
• Summing initial energy within a network loop with the friction
losses within that loop
• Basic parameters:
• NP = number of pipes
• NJ = number of junctions
• NL = number of loops
• Branched system and looped system
Supply source Pipe
Junction Demand Loop

(Source: Larock, Jeppson and Watters, 2000: Hydraulics of Pipeline Systems)

Pipe Network Analysis

• Equations for steady flow in networks

• Q-equations (pipe charges are the unknowns)
• H-equations (heads are the unknowns)
• ΔQ-equations (corrective discharges are the
unknowns)
• When the equations are established, may use
Newton method to solve them
• Linear algebra matrix operations
• Determine Jacobian matrix
• Iterative procedure to calculate desired discharges
Pipe Network Analysis

• Q-equations (assume flow as unknowns)

• Based on continuity
• Flow into a junction = Flow out of the junction
• QJj = flow out (demand)
•
QJ j   Q i  0 Qi = flow in from pipe i
• Based on work-energy principles
• Sum of the head loss around each loop is zero
• n hfi = head loss
• 
h fi  K i Qi  0
Ki, n = coefficients
Example of Q-equations for a simple network

Node [1]: Q1 + Q3 - 4.45 = 0

Node [2]: -Q1 + Q2+Q4 +1.11 = 0
Node [3]: -Q4 - Q5 + 3.34 = 0

Loop 1-2-3: K1Q1n + K2Q2n – K3Q3n = 0

Loop 4-5-2: K4Q4n – K5Q5n – K2Q2n = 0
Pipe Network Analysis

• H-equations (assume head as unknowns)

• Solve the exponential equation for the flow
1 / nij 1 / nij
Qij  (h f ij / K ij )  [( H i  H j ) / K ij )]
• Subscript ij = for the pipe from node i to node j
• Substitute the above into junction continuity equ.
1 / nij
QJ j   {[( H i  H j ) / K ij )] }in
1 / nij
  {[( H i  H j ) / K ij )] }out  0
 Example of H-equations for a simple network

Continuity equations:
Q12  Q13  QJ1  QJ 2  QJ 3
Q21  Q23  QJ 2 (or  Q12  Q23  QJ 2 )
H-equations (by substituting the Q above):
1 / n12 1 / n13
 H1  H 2   H1  H 3 
     QJ 2  QJ 3
 K12   K13 
1 / n12 1 / n23
 H1  H 2   H2  H3 
     QJ 2
 K12   K 23 
Pipe Network Analysis

• ΔQ-equations (corrective flows as unknowns)

• To obtain these equations, replace the flow in
energy loop equations by an initial Q0i, plus the
sum of all initially unknown corrective flow
Qi  Q0i   Qk
• Energy equation becomes
ni
 K {Q   Q }
i 0i k 0
• Nos. of equations can be reduced, but the
equations are nonlinear & contain many terms
Pipe Network Analysis

• Solving the network equations

• Newton iterative formula:
( m 1) (m) 1 (m)
{x}  {x}  [ D ] {F }
• {x} = entire column vector of unknowns
• {F} = entire column vector of equations
• [D]-1 = inverse of matrix [D], the Jacobian
Pipe Network Analysis

• Solving the network equations (cont’d)

• Newton method solves a system of nonlinear
equations by iteratively solving a system of linear
equations. The iterative formula is:
( m 1) (m)
{x}  {x}  {z}
• {z} = solution vector, solved by [D]{z} = {F}
• The solution is developed by using a multi-
dimensional Taylor series expansion to evaluate
the individual equation
An example of simple pipe network analysis (using MathCAD)
Pipe Network Analysis

• Computer solutions to networks

• Implement using equation solver package e.g.
MathCAD, or computer programs e.g. FORTRAN
• Other pipe analysis software are available, e.g.
EPANet (for water supply & distribution)
• http://www.epa.gov/nrmrl/wswrd/dw/epanet.html
• Simple demon. of piping simulation software:
• http://www.vcity.ou.edu/demoModules/piping/home.ht
m
 EPANET 2.0 interface
(Source: http://www.epa.gov/nrmrl/wswrd/dw/epanet.html)
Pipe Network Analysis

• After the analysis is done, the next step is to

verify by measurements in actual system
(network verification) & identify deficiencies
• Such as for designing water supply systems
• Application to HVAC systems
• At present, large network analysis is not common
in HVAC, except district cooling system (DCS)
• But the technique can be applied to studies of
water systems, air systems and building infiltration
Water Systems in HVAC

• HVAC water systems can be classified by

• Operating temperature
• Flow generation
• Pressurization
• Piping arrangement
• Pumping arrangement
Water Systems in HVAC

• Open water systems, e.g. using cooling tower

• Closed water systems
• Chilled water (CHW) system [4-13 oC, 825 kPa]
• Condenser water (CW) system
• Dual temperature water system
• Low temp. water (LTW) system [Max. 120 oC, < 1100 kPa]
• Medium temp. water (MTW) system [120-125 oC, < 1100
kPa]
• High temp. water (HTW) system [> 175 oC, > 2070 kPa]
• Once-through system, e.g. sea water system
Basic components of water (hydronic) system

(Source: ASHRAE HVAC Systems and Equipment Handbook 2004)

 Series circuit with load pumps
(Source: ASHRAE HVAC Systems and Equipment Handbook 2004)
Multiple chiller variable flow chilled water system

(Source: ASHRAE HVAC Systems and Equipment Handbook 2004)

2-pipe direct return 2-pipe reverse return
(Source: ASHRAE HVAC Systems and Equipment Handbook 2004)
 4-pipe system (dual temperature)

(Source: ASHRAE HVAC Systems and Equipment Handbook 2004)

Water Systems in HVAC

• Heat transfer in water systems

• Terminal units/devices that convey heat
from/to water for heating/cooling
• Common heat exchangers
• Water-to-air finned coil
• Water-to-water
• Heating load devices, e.g. radiators
• Cooling load devices, e.g. fan coil units
(FCU)
Calculate Heat Transferred to or from Water:
Water Systems in HVAC

• Design issues
• Design water temperature
• Flow rate
• Piping layout
• Pump selection
• Terminal unit selection
• Control method
Water Systems in HVAC

• Design principles
• Constant flow? Variable flow? Intermittent flow?
• Direct return piping or reverse return piping
• Direct return riser & reverse zone piping
• Design factors
• Pump speed controls
• Pressure distribution
• System balancing
• Thermal expansion & joints (or loops)
Water Systems in HVAC

• Piping materials
• Chilled water: black & galvanized steel
• Hot water: black steel, hard copper
• Condenser water: black steel, galvanized ductile iron, PVC
• Flow rate measurements
• Venturi, nozzle & orifice flowmeters
• Variable area flowmeters (rotameters)
• Turbine flowmeters
Water Systems in HVAC

• Other design considerations

• Makeup water (from city water or wells)
• Safety relief valves (for pressurised systems)
• Air elimination (e.g. by air separator/vent)
• Drain (at low points) & shutoff (for isolation)
• Balance fittings (allow balancing of sub-circuits)
• Strainers (remove dirt)
• Insulation (reduce heat loss & condensation)
• Condensate drains (to drainage system or recover)
Water Systems in HVAC

• Practical design process (see reference)

• See “Practical Guide to HVAC Building Services
Calculations” - water flow distribution
systems: overview of system design process
• W1 Pipe sizing – general
• W2 Pipe sizing – straight length
• W3 Pipe sizing – pressure drop across fittings
• W4 System resistance for pipework – index run
• W5 Pump sizing
• W6 Water system pressurisation