MAXIMUM RECOMMENDED STRING WIDTH 2.50” (63.

5)
3.500 R .125
(88.9) TYP

1.500
(38.1)
0230-0119rC

PO BOX 4394
SANTA ROSA, CA
95402 USA
3.250
P (707) 525-9941 (82.5)
.125 (3.17) DIA. MOUNTING HOLES
B136rE

F (707) 575-7046
EMGPICKUPS.COM

.750 (19.0)
INSTALLATION INFORMATION .880 (22.3)

EMG MODEL: 707-TW

SPECIFICATIONS: MODEL:
707-TW Single-Coil Dual-Coil EMG-707-TW (SIDE VIEW)
Logo Color Copper
Magnet Type* C/S
Resonant Frequency (KHz) 3.76 1.80 C1 C2
Output Voltage (Finger, Thumb) 1.00 2.00 C3
Output Voltage (Thump) 3.00 4.50
Output Noise (60 Hz) -107 -109
Output Impedance (Kohm) 10 10
Current @9V (Microamps) 160 In Dual-coil mode, coils C1 and C2 are active.
Battery Life (Hours) 1500 In Single-coil mode, coils C2 andC3 are active.
Maximum Supply (Volts DC) 27
* Magnet Type CS (Ceramic and Steel)

Installation notes:
The EMG-707-TW has a variety of ways it can be wired into a guitar. The diagrams included are limited to the most popular because of space.
The additon of the plug-on PC Board on the Push-Pull Pot adds further flexibility as you will see in the diagrams. We suggest you look fully at the
installation diagrams included in this sheet along with the B245 Pickup Buss data sheet included in this package before beginning your installation.
The Push-Pull Pot allows you 2 options as a volume control as well as 2 other options using the pot as a tone control. If you don’t see a diagram that
fits your instrument directly, or you want to do something completely different, contact our technical department and we’ll create a diagram you can
follow for your installation. Certain limitations apply...

Included with each pickup:

1 TONE CONTROL (25K) 1 TW P/P SWITCH
W/POT (25K) 2 PICKUP IN/ OUT
BATTERY BUSS
.235 (6)
TW PICKUP CABLE 15” (38cm)

.390 .310 (8)

(10)
B245

2 CONNECT CABLES 5.5” (14cm)

STEREO OUTPUT
JACK BATTERY OUTPUT CABLE 6” (15cm)
BUSS
ADJUSTMENT SCREWS

BATTERY CABLE 7” (18cm)

- 9V +

Warranty
All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If
upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This
warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.
© 2014 Copyright EMG INC. All Rights Reserved.
 General Notes:
Every attempt has been made to make this a solderless installation.
There are some instances where this is not possible;
1) If your instrument uses the long panel output jack and you had passive pickups
you will need a new stereo output jack, the Switchcraft 152B is recommended. 1
Soldering to the new jack will be required. 2
2) Some instruments may already have a battery holder installed, in that case 3 WIRE ORDER:
soldering may be required. WHITE
3) Instruments with two pickups may need soldering to the selection GREEN
switch in some installations. BLUE
YELLOW
Using the TW Push-Pull Switch Diagram #1 ORANGE
The Push-Pull Switch included with the TW Pickup allows you to choose between HUMBUCKING ON: DOWN POSITION SHIELD
two internal pickups of the EMG-TW, single-coil and dual-coil. The Push-Pull Pot SINGLE COIL ON: UP POSITION
has two seperate sections: The Switch and the pot, described below.
FLIP CONNECTORS 1 AND 2
Refer to Diagrams #1 and #2
AS SHOWN
The Push-Pull Switch section (DPDT) lets you choose between the
single-coil sound and a dual-coil sound by pulling or pushing the pot shaft 1
up or down. You have the option of having the single-coil sound in either 2
the up or down position and vice-versa for the dual-coil sound. WIRE ORDER:
3
Diagrams #1 and #2 show how to connect the TW Pickup cable to choose GREEN
either option. Select the diagram that suits you and push the cable WHITE
connectors onto the single line 6-pin header. YELLOW
Simply turn over cable connectors 1 and 2 to change the wire order Diagram #2 BLUE
and this will choose between the two options. SINGLE-COIL ON: DOWN POSITION ORANGE
Connector 3 remains the same for either choice. HUMBUCKING ON: UP POSITION SHIELD

Diagram #3
PUSH / PULL POT USED AS B136rE
Using the TW Push-Pull Pot Section
THE PICKUP VOLUME CONTROL The Push-Pull Pot side of the EMG-TW allows you 4 different options:
1) Use the pot as a Master Volume for the Instrument
2) Use the pot as a Volume control for the TW Pickup
PICKUP OUTPUT 3) Use the pot as a Master Tone control for the Instrument
(H1 or H2) 4) Use the pot as a Tone control for the TW pickup

INSTALL SHUNT (H4) On the PC Board there is a dual-line header with 6 pairs of pins. They are
listed on the PC Board as H1 through H6. By using the the connections
INSTALL SHUNT (H6) shown in Diagrams #3 through #6, you can choose any of the 4 options.

Using the Pot Section as:

1) The Pickup Volume control, or a Master Volume for the Instrument.
PICKUP OUTPUT: Refer to Diagrams #3 and #4
TO TONE CONTROL OR The pot section (25KA) can be used either as a Volume control
SELECTION SWITCH OR BUSS for the pickup or, it can be used as the Master Volume for the guitar.
FOR 2 OR 3 PICKUP GUITARS Diagrams #3 and #4 show how to connect either option.
Use the dual-line 12-pin header and push the cables on and
install the shunts as needed onto the labeled headers H1 thru H6.
OR TO THE OUTPUT JACK IN SINGLE
PICKUP GUITARS WITH NO TONE Use Diagram #3 if you have a single TW installed in your instrument,
CONTROL or have two or more pickups in your instrument and want to use the
pot as the Volume control for the TW Pickup only.
Diagram #4 Installing the shunts on positions H4 and H6 sends the pickup signal
PUSH / PULL POT USED AS to the wiper of the 25K Pot, and the output of the 25K Pot is at position
MASTER VOLUME H1 or H2.
THE MASTER VOLUME CONTROL
INPUT (H1 OR H2)
MASTER VOLUME Diagram #4 allows you to use the 25K Pot independently of the pickup output.
OUTPUT (H3) By taking the output of the pickup from position H5, the Volume control is now
available to use as a Master Volume with H1 or H2 being the input to the Volume
PICKUP OUTPUT (H5) control. H1 and H2 positions are interchangeable.
Position H5, now the output of the pickup, would typically go to a selection switch
SHUNT ON (H6) or a pan-pot. Don’t forget to install the shunt on H6.

TO SELECTION SWITCH
(VIA B245 BUSS)
OR PAN-POT

707-TW INSTRUCTIONS Page 2

Diagram #5
PP POT USED AS THE PICKUP
Using the Pot Section as:
TONE CONTROL
2) The Pickup Tone control or as a Master Tone control for the instrument.
Refer to Diagrams #5 and #6
The pot section (25KA) can be used either as a Tone control
PICKUP OUTPUT for the pickup or it can be used as a Master Tone control for the guitar.
(H1 or H2) Diagrams #5 and #6 show how to connect either option.
Use the dual-line header, push the cables on and install the shunts
INSTALL SHUNT ON (H4) as needed onto headers H1 thru H6.

Use Diagram #5 if you have a single 707-TW installed in your instrument,

or have two or more pickups in your instrument and want to use the pot as the
PICKUP OUTPUT: Tone control for the 707-TW Pickup only.
TO VOLUME CONTROL Installing the shunt on position H4 connects a tone capacitor on the PC Board
SELECTION SWITCH OR... to the wiper of the 25K Pot and creates a passive Tone control. The output of
pickup can be either position H1 or H2.
Diagram #6
PUSH-PULL POT USED AS A MASTER OUTPUT OF TONE CONTROL Diagram #6 uses the 25K Tone control independently of the pickup output.
TONE CONTROL (H1 or H2) ONLY IF NEEDED By taking the output of the pickup from Position H5, the control is now
available to use as a Tone Control independent of the pickup output.
INPUT TO TONE CONTROL (H3) Position H3 is the input to the Tone Control, with H1 or H2 being the output of
the control, if necessary.
PICKUP OUTPUT Position H5, the output of the pickup, would typically go to a selection switch
(H5)
or output jack.
PICKUP OUTPUT TO
SELECTION SWITCH,
EMG ACCESSORY, OR... Diagram #7
Insert the plug onto the 7 pin header
of the pickup as shown above.
Note the orientation arrow.

RED
- 9V +
RED
BATTERY
Diagram #8 NEG (-)
One TW Pickup BATTERY
Master Volume BUSS

PICKUP
VOLUME
CONTROL OUTPUT
R
FROM PICKUP S

RED
- 9V +
RED
Diagram #9
One TW Pickup BATTERY
Master Volume and Tone Control BUSS
BATTERY
PICKUP MASTER TONE NEG (-)
B124rH
VOLUME
CONTROL

TONE

FROM PICKUP OUTPUT

R
S

707-TW INSTRUCTIONS Page 3 T

 - 9V +
BATTERY
NEG (-)
GROUND

NECK P/U
MASTER
TONE
OUTPUT RED B124rH

RED R
TONE
BRIDGE P/U MASTER S
RED
VOLUME

BRIDGE PICKUP
T
Diagram #10
2 Pickups (1 EMG / 1 EMG-TW)
Toggle Style Select Switch
Push-Pull Pot as Master Volume
with a Master Tone (Passive) OUTPUT CABLE

NECK EMG-TW PICKUP

Refer to Diagram #10 Above: Refer to Diagram #11 Below:

1) Install the Pickups and route the cables to the control cavity keeping 1) Install the 707-TW Pickups and route the cables to the control cavity keeping
any excess cable under the pickup. any excess cable under the pickup.
2) Choose an up/down option from Diagram #1 or #2 and plug the 707-TW 2) Choose an up/down option from Diagram #1 or #2 and plug the 707-TW
Pickup cable onto the push-pull pot. Pickup
3) Route a coax cable from the push/pull pot (H4) to the Pickup buss, Position 1. cables onto the push-pull switch sections.
Plug the pickup cable of the other EMG into Position 2 of the pickup buss. 3) Route a coax cable from each of the Push-Pull Pots (H1) to the Tone controls.
4) Plug a coax cable from Position 3 of the Pickup Buss to the Tone control. 4) Plug a coax cable from the Bridge Tone to the Pickup Buss (Position 1)
Plug a coax cable from the Tone control to the Push-Pull Pot (H1) Plug a coax cable from the Neck Tone to the Pickup Buss (Position 2)
5) Plug the output cable from the Push-Pull Pot (H2) to the output jack and push 5) Plug the output cable from the Pickup Buss (Position 3) to the output jack and
the connectors onto the T, S, and R terminals of the jack as shown. push the connectors onto the T, S, and R terminals of the jack as shown.
6) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud) 6) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
with the RED wire of the battery clip. with the RED wire of the battery clip.
7) Strip the insulation from the switch wires and Insert them into the GREEN 7) Strip the insulation from the switch wires and Insert them into the GREEN
and BLACK Terminal Blocks and tighten the screws with a small screwdriver. and BLACK Terminal Blocks and tighten the screws with a small screwdriver.
Refer to the B157 Pickup buss instructions enclosed. Refer to the B157 Pickup buss instructions enclosed.
8) Put the battery in the insulating foam piece provided and place it securely in 8) Put the battery in the insulating foam piece provided and place it securely in
the control cavity. the control cavity.
We suggest that you plug in the instrument and test it before closing the We suggest that you plug in the instrument and test it before closing the
control cavity. control cavity.

- 9V + BATTERY
NEG (-) R
GROUND S

NECK P/U
T
OUTPUT CABLE
OUTPUT RED OUTPUT

BRIDGE P/U
Diagram #11
2 TW Pickups
2 Push-Pull Pots as Volume controls RED
NECK
(Volumes are independent) VOLUME
2 Tones (Passive) NECK TONE
B124rH
Toggle Style Switch
EMG-TW PICKUP (NECK)
TONE

RED
BRIDGE
VOLUME
BRIDGE TONE
B124rH

EMG-TW PICKUP (BRIDGE)

TONE

707-TW INSTRUCTIONS Page 4