Scribd
Upload
225 views4 pages

INDU 372: Several Sample Questions For Final Exam

The document provides 3 sample questions for a final exam in INDU 372. Question 1 involves calculating control limits for a u-chart using 20 samples of 50 units each. Question 2 calculates the consumer's and producer's risk for a single sampling plan with lots of 300 and a sample of 10. Question 3 involves drawing a reliability block diagram and calculating the reliability for a series-parallel system with 3 subsystems of varying components.

Uploaded by

Youssef Wael
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
225 views4 pages

INDU 372: Several Sample Questions For Final Exam

The document provides 3 sample questions for a final exam in INDU 372. Question 1 involves calculating control limits for a u-chart using 20 samples of 50 units each. Question 2 calculates the consumer's and producer's risk for a single sampling plan with lots of 300 and a sample of 10. Question 3 involves drawing a reliability block diagram and calculating the reliability for a series-parallel system with 3 subsystems of varying components.

Uploaded by

Youssef Wael
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

INDU 372: Several Sample Questions for Final Exam

* There will be more questions in the actual final exam.

Instructions:
 This is a close book exam. The total marks is 45.
 Enter your name and ID number on the answer booklet.
 Answer all the questions on the answer booklet, following the order of question number.
 Show all the intermediate steps of your solution.
 Standard type calculator can be used.
 Exam question sheets are to be returned together with the answer booklet.

Question 1:

Given the following 20 samples with 50 units each. Calculate the control limits for the u-
chart and plot it.

1
Question 2

Consider a single sampling plan. Suppose the products are shipped from the producer to
the buyer in 300-product lots. They agree that a 5% rate of defectives is acceptable and a
15% rate of defectives is unacceptable. For each lot, the following sampling plan is used:
10 products are sampled, if more than 1 are found defective, the lot is rejected.
Calculate the consumer’s risk and the producer’s risk.

Question 3

Suppose we have a series-parallel system (each subsystem is a parallel system) with 3


subsystems. Subsystem A has 3 components (a1, a2, a3), Subsystem B has 2 components
(b1, b2), and Subsystem C has 4 components (c1, c2, c3, c4). Suppose the reliability of a
component in subsystem A is Ra=0.9, the reliability of a component in subsystem B is
Rb=0.7, and the reliability of a component in subsystem C is Rc=0.5.

(1) Draw the RBD for this system.


(2) Calculate the system reliability

2
Solutions
* For some questions, only the key solution information is given. You need to provide the
complete solutions during the actual final exam.

Question 1:

xi
Calculate ui  , shown in the following table:
n

20

u i
1.48
u i 1
  0.0740
20 20
u 0.0740
UCL= u  3  0.0740  3  0.1894
n 50
Center Line = u =0.0740

u 0.0740
LCL= u  3  0.0740  3  0.0414
n 50
3
LCL=0.0

The control chart is:

Question 2:

(1) Producer’s risk: .

(2) Consumer’s risk: .

Question 3:

a1 b1 c1

c2
a2
c3

a3 b2 c4

You might also like