Scribd
Upload
1K views4 pages

Drawing Question Paper

1. The document contains instructions for an engineering drawing exam, including questions on: - Drawing capital letters to specifications - Calculating and drawing a scale for a railway map - Drawing orthographic views from an isometric view - Drawing conventional symbols and view projections 2. It provides details on dimensions, projections, scales, views, symbols and other concepts that will be assessed on the exam. 3. Students are instructed to follow first angle projection, show dimensions in mm, and attempt all questions.

Uploaded by

Hshdv Dev
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views4 pages

Drawing Question Paper

1. The document contains instructions for an engineering drawing exam, including questions on: - Drawing capital letters to specifications - Calculating and drawing a scale for a railway map - Drawing orthographic views from an isometric view - Drawing conventional symbols and view projections 2. It provides details on dimensions, projections, scales, views, symbols and other concepts that will be assessed on the exam. 3. Students are instructed to follow first angle projection, show dimensions in mm, and attempt all questions.

Uploaded by

Hshdv Dev
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

1.

Write the following words in single stroke capital

letters (instrumental) using the ratio 7:4 height


35mm.

“AMERICAN STANDARD CODE” (15)


Roll No.....................
2. The distance between two railway stations
Total No. of Questions—5] [Total No. of Printed Pages—7
Ambala and Delhi is 200 Km. It is represented

ED-17106 on the railway map by a distance of 10 cm. Find

RF of the scale. Draw a diagonal scale to


First Semester Common (N-2017)
measure up to a single Km and indicate on the
(Common to All)
map by a diagonal scale the following distances :
ENGINEERING DRAWING-I
(a) 221 Km
Time : 4 Hrs. M.M. 100
(b) 136 Km
Note :— 1. First angle projection should
be followed. (c) 58 Km (15)

2. All dimensions are in mm. 3. Figure-I shows an isometric view of an object.


Missing data if any, may be Draw the follwing orthographic views in first
assumed proportionally. angle projections using a suitable scale.

3. Attempt all the questions.

293/0720/ED-17106/8/7/630 1 293/0720/ED-17106/8/7/630 2
(a) Elevation looking in the direction of arrow ‘F’ Figure-II shows an isometric view of an object.

Draw the following orthographic views in first


(b) Side View
angle projections using a suitable scale.

(c) Top View (10 + 10 + 10 = 30)


(a) Front view full in section looking in the

direction of arrow ‘F’

(b) Side view looking in the direction of arrow

‘S’

(c) Top view (10 + 10 + 10 = 30)

OR

293/0720/ED-17106/8/7/630 3 293/0720/ED-17106/8/7/630 4
4. (a) Draw the conventional symbols for any two (iii) A point C situated in the HP and 25

lines : mm in front of VP

(i) Dimension line (iv) A point D 20 mm below HP and 30 in

front of VP
(ii) Lines of symmetry
(5 + 5 + 10 = 20)

(iii) Cutting plane line


5. Draw the symbols of following :

(b) Explain with simple sketch, the method of


(a) Urinal corner hung
dimensioning of any one from following :

(b) Ceiling fan


(i) Chamfering on rod

(c) Indian type (WC)


(ii) Counter sunk hole

(d) Generator
(c) Draw the projections of the points situated in

the fourth quadrant :


(e) Safety valve

(i) A point A situated in both the planes


(f) Pump

(ii) A point B in the VP and 30 mm below


(g) Ammeter
HP

293/0720/ED-17106/8/7/630 5 293/0720/ED-17106/8/7/630 6
(h) Immersion water heater

(i) Drain cock

(j) Water meter (20)

293/0720/ED-17106/8/7/630 7

You might also like