Scribd
Upload
573 views6 pages

Etabs Check List

This document contains 27 sections detailing the parameters and considerations for modeling and analyzing a structural building model in ETABS. It includes specifications for the building geometry, materials, loads, soil properties, seismic analysis parameters according to Indian codes, results of static and dynamic analysis like base shear, storey drift, and deflection. Mode shapes, load combinations, and deflection values are to be attached.

Uploaded by

Lokeswar Saha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
573 views6 pages

Etabs Check List

This document contains 27 sections detailing the parameters and considerations for modeling and analyzing a structural building model in ETABS. It includes specifications for the building geometry, materials, loads, soil properties, seismic analysis parameters according to Indian codes, results of static and dynamic analysis like base shear, storey drift, and deflection. Mode shapes, load combinations, and deflection values are to be attached.

Uploaded by

Lokeswar Saha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

M. N. Consultants Pvt. Ltd.

mn
Civil & Structural Engineers

Check print for E-Tab model Date:-


Project Name:
Type of Building:
1. Geometry:

l= w= h=
2. Structural Arrangement :

3. Material Property:
Slab: Beam:
Column: Shear Wall:

4. Member Property:

Slab:
Beam:

Column:

Shear Wall:

Tie Beam :

5. Soft Storey :

(As per Table 5 , Sl No. 1 of IS 1893 (Part 1):2002 )

6. Fire Rating :

7. Fire Tender Load :


8. Diaphragm(Check for Temperature Load) :

9. P-Delta :

10. Type of Meshing :


11.Live load reduction for Eqx & Eqy combo (Attach load combination Sheet)
:

12.Moment release for non-framing beam :


13. Auto Line Constraint :
14.Check model (no error should be shown) :

15.Total Load:
a) Dead Load =
b) Live Load =

c) Super Dead Load =

d) Brick work Load =

Dead Load + Reduced Live Load =

(As per clause 3.2.1 of IS 875 (Part 2):1987 )


Floor Area = Load/Area =

16. Bearing Capacity of Soil :

17.Type of Foundation :

18.Wind analysis (Please write in a detail consideration) :

Location:
Wind speed : (As per APPENDIX A of IS 875 (Part 3):1987 )
Risk Coefficient :
(As per clause 5.3.1 & Table 1 of IS 875 (Part 3):1987 )
Topography Factor :
(As per clause 5.3.3.1 of IS 875 (Part 3):1987 )
Terrain Category :
(As per clause 5.3.2.1 of IS 875 (Part 3):1987 )
Structural Class :
(As per clause 5.3.2.2 of IS 875 (Part 3):1987 )
h/w = l/w =
Cp : (As per clause 6.2.2.1 & Table 4 of IS 875 (Part 3):1987 )

θ=0⁰ windward =
leeward =
θ=90⁰ windward =
leeward =
Gust Factor (If yes attached calculation):

19. Seismic analysis:

Location: Zone:
Zone factor, Z= (As per Table 2 of IS 1893 (Part 1):2002 )

Soil type :

Percentage of total base shear force taken by column :

BASE SHEAR CHART

LOAD CASE COLUMN SHEAR WALL TOTAL

SLX (Ton)

% OF TOTAL BASE
SHEAR IN X-DIR

SLY (Ton)

% OF TOTAL BASE
SHEAR IN Y-DIR

Response Reduction Factor, R =


(As per Table 7 of IS 1893 (Part
1):2002 )

Importance Factor, I =

(As per Table 6 of IS 1893 (Part


1):2002 )

Response Spectrum:
i) Modal combination: CQS
ii) Directional combination :SRSS
iii) Eccentricity Ratio (Accidental): 0.05

Scale Factor = Ig/2R =

20. Mass Source :

(As per Clause 7.3.1 & Table 8 of IS 1893 (Part 1):2002 )

21. No. of modes required to consider 90% of total seismic mass :


(As per Clause 7.8.4.2 of IS 1893 (Part 1):2002 )

22.TIME PERIOD & BASE SHEAR (Hand calculation) :

Design Base Shear , Vb =Ah* W =

(Ah )X= Design horz. Seismic coefficient = ZISa/g2R =


(Ah )Y= Design horz. Seismic coefficient = ZISa/g2R =
W= Seismic Weight of the Building = DL + Reduced LL) =

A) With Brick infill :


Time Period: (As per clause 7.6.2 of IS 1893 (Part 1):2002 )
Tx = 0.09H/L0.5 =
Sa/g =
Ty = 0.09H/B0.5 =
Sa/g =
Base Shear:
SLX =
SLY =

B) Without brick infill :


Time Period: (As per clause 7.6.1 of IS 1893 (Part 1):2002 )

Tx = Ty = 0.075 H0.75 =
Sa/g =
Base Shear:
SLX =
SLY =

C) Average brick infill :


Time Period:
Tx = 0.9H/L0.5 =
Sa/g =
Ty = 0.9H/B0.5 =
Sa/g =
Base Shear:
SLX =
SLY =

23. Design Base Shear as per ETABS :


SLX =
SLY =
SPECX =
SPECY =

24. Enhancement : (As per clause 7.8.2 of IS 1893 (Part 1):2002 )


Enhancement Factor in X-dir = (SLX/SPECX) x (Ig/2R) =

Enhancement Factor in Y-dir = (SLY/SPECY) x (Ig/2R) =

25. Expansion gap between adjacent buildings :


(As per clause 7.8.2 of IS 1893 (Part 1):2002 )
Calculation:

26. Maximum Storey Drift (From ETABS) =


(As per clause 7.11.1 of IS 1893 (Part 1):2002 story drifts shall not exceed
0.004 times the storey height)

27. Maximum Deflection (From ETABS) =

(Lateral deflection should not exceed (H/500) As per clause 20.5 of IS 456:2000)

DEFLECTION CHART
LOAD CASE DEFLECTION (mm) IN TERMS OF 'H'
H/
SEISMIC 'X'
H/
SEISMIC 'Y'
H/
SPEC 'X'

SPEC 'Y' H/

WIND STATIC 'X' H/

WIND STATIC 'Y' H/

WIND DYNAMIC 'X' H/

WIND DYNAMIC 'Y' H/

H= HEIGHT OF THE BUILDING FROM GROUND TO PARAPET = 80.5 M.

NOTE:
i) Mode shapes to be attached.
ii) Load schedule to be attached.
iii) Deflection value to be attached.

21. Dynamic Analysis

a) 1st Mode: Time Period = Sec

b) 2nd Mode: Time Period = Sec

c) 3rd mode: Time Period = Sec

You might also like